DP KKD 2025-26 Proj.1109/26 Kanjikkavu khadi Renovation Balussery pt

BUILDING WORK

11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

OD265175/2025-2026:DRY RUBBLE MASONRY-Dry rubble without concrete leveeling course masonrywith good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour cjharges etc complete as per direction of departmental officers at site

50.6.7.2:Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

10.16.1:Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

OD265256/2025-2026:Supplying and fixing half split PVC gutter 200 mm size with MS flat 200x5 mm size @60 cm c/c fixing on roof members ,bolts ,nuts and washers including makingnecessary connections with rain water pipes complete

OD329884/2025-2026:Providing and fixing precoated galvanised iron profile sheets(size,shape pitch of corrugation as provided by engineer in charge 0.35mm (+0.05%)total coated thickness with Zinc coating 120gms per sqm as per IS -277 in 240 mpa steel grade 5-7 microns epoxy primer on both sides of the sheet and polyster top coat 15-18 microns.sheet should have protective guard filim of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12m or as desired by engineer in charge.The sheet shall be fixed using self drilling /self tapping screws of size (5.5x55mm) with EPDM seat, complete upto any pitch in horizontal /verticalor curved surface ,excluding the cost of purlins,rafters,and trusses and including cutting to size and shape wherever required

OD265268/2025-2026:Providing and laying factory made coloured and polished Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of 6mm, compacting and proper embedding/laying of inter locking paver blocks into the 6 mm bedding layer through vibratory compaction by using plate vibrator, cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer’s specifications & direction of Engineer in-Charge. 60mm thick C.C. paver block with approved colour, design & pattern. modified 16.91

15.9.1:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In Lime Mortar

Please Enable Macros to View BoQ information