Construction of Veternary Polyclinic Building at Village Dhandhoda (Ground Floor) Ta. and Dist. Chhotaudepur

Name of work :-

Construction of Veternity Polycleanic Building at Village Dhandhoda (Ground Floor) Ta. and Dist :-

Bill of Quantities

(A) Percentage Rate Tender (Up to INR 50 Cr. )

m Item of work Quantity Unit Amount

1 Excavation for foundation upto 1.50 mt depth including sorting out 929.00 Cumt 125.86

and stacking of useful materials and disposing the excavated stuff

all lead and lift. (A) Loose or soft soil.

2 Excavation for foundation 1.50 mt to 3.00 mt depth including sorting 149.10 Cumt 174.56

out and stacking of useful materials and disposing the excavated stuff

all lead and lift.(B) Dense or hard soil

3 Filling in foundation and plinth with sand in layers of 20 cm. Thickness 272.20 Cumt 489.28

including watering ramming and consolidating etc. comp. with all lead

4 Filling foundation and plinth with murrum or selected soil in layer of 20 425.70 Cumt 304.60

cm in thickness including ramming watering and consolidating etc.

complete with all lead and lift.

5 Filling available excavated Earth (Excluding Rock) in trench plinth side 609.00 Cumt 137.47

of foundation . in layer not excluding 20 cm in depth consolidation

each deposited layer by ramming and watering etc. complete

6 Applying general insecticide pest control treatment to floors, 961.30 Sqm 49.25

cupboards etc including labour materials etc. complete. Using

Imidacloprid 20 EC As Per 6113 pests Consentration Weight

percent is recommended on litre chemical emulsion dilute with 39 liter

of water will give. Total dilute concrentration with will be 40 litre

inclusive of one litre chemical emulsion application 0.5 litre chemical

/Sqm of surface is recommended as per I.S.

7 Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand 219.40 Cumt 3245.91

: 6- Crushed stone aggregates 40 mm nominal size) and curing

complete including cost of formwork in (A) Foundation and Plinth

8 Providing and laying controlled cement concrete M.250 and curing 252.10 Cumt 4882.34

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (A)

Foundations, footings and Mass concrete. Footing

9 Providing and laying controlled cement concrete M-250 and curing 48.90 Cumt 8301.19

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (d)

columns Up to Plinth level.

10 Providing and laying controlled cement concrete M-200 and curing 61.70 Cumt 8215.34

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in

Columns, pillars posts and struts Ground Floor to First floor

11 Providing and laying controlled cement concrete M-250 and curing 122.70 Cumt 5979.20

complete including the cost of form work but with Ply & Cuplock

excluding the cost of reinforcement for reinforced concrete work in

Ground & Plinth BEAMS

12 Providing and laying controlled cement concrete M.150 and curing 132.20 Cumt 4282.40

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (C)

13 Providing and laying controlled cement concrete M.200 and curing 159.50 Cumt 6690.24

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (C)

Ground floor to First floor Slab

14 Providing and laying controlled cement concrete M.200 and curing 130.90 Cumt 6268.06

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (C)

Ground floor to First floor Beams

15 Providing and laying controlled cement concrete M-200 and curing etc. 19.20 Cumt 6062.02

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (c)

Chhajja for Ground floor to First floor

16 Providing and laying controlled cement concrete M-200 and curing etc. 4.80 Cumt 6428.65

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (c)

Lintel for Ground floor to First floor

17 Providing and laying controlled cement concrete M-200 and curing etc. 2.30 Cumt 7219.48

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in (E)

Stair case up to floor two level for Ground floor to First floor

18 Providing and laying controlled cement concrete M-200 and curing etc. 0.30 Cumt 7269.97

complete including the cost of form work with Ply & Cuplock but

excluding the cost of reinforcement for reinforced concrete work in

RCC Vertical and horizontal wall for Ground floor to First floor

19 Providing and laying controlled cement concrete M-200 for RCC work 23.50 Cumt 6762.96

and curing complete including the cost of form work with Ply &

Cuplock but excluding the cost of reinforced concrete work in coping

on Ground Floor to First floor

20 Providing TMT Bar FE 500D reinforcement for R.C.C. work including 102274.00 Kg 77.37

bending, binding and placing in position complete up to All floor Level

21 Brick work using common burnt clay building bricks crushing strength 151.30 Cumt 4279.98

not less than 35 kg/sq.cm. in foundation and plinth in cement mortar

1:6 (1 cement : 6 fine sand) (B) Conventional For below plinth

22 Brick work using common burnt clay building bricks crushing strength 309.40 Cumt 4579.34

not less than 35 Kg/Sq.cm. in super structure above plinth level upto

floor two level in cement mortar 1:6 (1cement : 6 fine sand) (B)

Conventional For Ground Floor to First floor

23 Half brick masonry in common brunt clay building bricks having 318.00 Sqmt 696.90

crushing strength not less than 35Kg/Sm. In C.M 1:4( 1cement :

coarse sand) in super structure.(B) Conventional For Ground Floor to

24 Providing 15mm thick mala cement plaster in single coat on Rough 2650.20 Sqmt 179.78

(Similar)side of single or brick walls for interior plastering upto floor

two level and finished even and smooth in (ii) Cement mortar 1:4 (1-

cement :4-sand) including Mala troveled finish with 5mm Groves at

juction of structure member etc complete For .Ground Floor to First

25 Providing 10 mm. Thick Mala cement plaster in single coat for 1188.80 Sqmt 162.61

plastering on ceiling and soffits of stairs and finished even and

smooth in : (I) Cement mortar 1:4 (1 cement : 4 sand) including Mala

troveled finish with 5mm Groves at juction of structure member etc

complete For .Ground Floor to First floor

26 23 mm Thick sand faced cement plaster with Gutka Finish on walls 2017.20 Sqmt 353.98

upto height 10 meters above ground level consisting of 18 mm Thick

backing coat of c.m. 1:3 (1 cement : 3 sand) and 5 mm Thick finishing

coat of c.m. 1:1 (1 cement : 1 sand) with 10x5mm Groves at juction of

structure member etc. comp.etc. complete.

27 Providing and fixing 150 mm Wide approved quality chicken wire mesh 605.00 Sqmt 52.52

at junction of brick work and RCC work or two dissimilar surfaces, at all

heights fixed by nails, rowal plugs or tag by cement mortar 1:3 before

applying the plaster, including curing, scaffolding all complete as

28 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 289.00 Rmt 44.07

29 Applying two coats of (white cement based) or (acrylic lappy (putty)) 3940.50 Sqmt 40.59

and two coats of primer of approved brand and manufacture on new

wall surface to give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign matter and sand

papered smooth.

30 Wall painting (Three coats) with plastic emulsion paint of approved 2751.70 Sqmt 128.38

brand and manufacture on undecorated wall surface to give an even

shade including one Coat water based Primer and throughly brushing

the surface free from mortar droppings and other foreign matter and

sand papered smooth.

31 Wall painting (Three coats) with plastic emulsion paint of approved 1188.80 Sqmt 134.04

brand and manufacture on undecorated ceiling surface to give an even

shade including including one Coat water based Primer and throughly

brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

32 Providing One Coat of Alkali Resistant Primer on exterior wall surface 2017.20 Sqmt 40.40

of approved brand after thoroughly brushing surface to remove all

dust and remains of loose powdered material etc. copm. for all height

33 Wall Painting (Two coats) with weather proof acraylic emulsion paint 4031.20 Sqmt 122.14

of approved brand and manufacture and of required shade on exterior

wall surface to give an even shade over of approved brand after

thoroughly brushing surface to remove all dust and remains of loose

powdered material etc. copm. for all height

34 Providing and laying water proofing treatment by conventional 944.00 Sqmt 922.13

method including cleaning the slab surface by wire brush as directed

including provding first layer of C.M. 1:4 of 40 mm thickness mixed

with water proofing compound at rate prescribed by manufacturer,

including putting of brick bats of average thickness 40 mm Well

immerssed in water laid uniformly on first layer of mortar including

applying cement slurry @ rate of 0.08 bag/sqm. on fixed layer of brick

bats including maintaining necessary slope, in second layer 40 mm

thick C.M 1:4 mixed with water proofing compound as directed,

including finishing smooth with cement slurry as directed complete.

35 Providing and fixing window having extruded aluminum Colour 38.60 Sqmt 1821.03

anodized section Horizontal Three Track member size 95mmx

24.10mm x 1.17mm,@ Wt.0.738 Kg/mt and Vertical member of size

92mm x 31.75mm x 1.50mm @Wt. 1.06 Kg/mt, with Three Glass

shutters of horizontal member size 40mm x 18mm x 1.29mm (@ wt.of

0.456Kg/mt), vertical member of size 40mm x 18mm x 1.29mm (@

wt.of 0.456Kg/mt) with 5 mm thick Transparent Float glass with

powder coated aluminum fittings & fixtures and Lock Strip

transparent silicon sealant glass fixing to frame as per details etc

36 complete for window.

Providing and W1,W2

fixing window having extruded aluminum Colour 21.60 Sqmt 1966.47

anodized section Horizontal Two Track member size 95mmx 24.10mm

x 1.17mm,@ Wt.0.738 Kg/mt and Vertical member of size 92mm x

31.75mm x 1.50mm @Wt. 1.06 Kg/mt, with Two Glass shutters of

horizontal member size 40mm x 18mm x 1.29mm (@ wt.of

0.456Kg/mt), vertical member of size 40mm x 18mm x 1.29mm (@

wt.of 0.456Kg/mt) with 5 mm thick Transparent Float glass with

powder coated aluminum fittings & fixtures and Lock Strip

transparent silicon sealant glass fixing to frame as per details etc

complete for window. W3

37 Providing & Fixing in position standard extruded approved colour 4.40 Sqmt 2050.30

anodised Aluminum Ventilator with outer frame 65 x 25 mm Stander

Box Frame(of Jindal Section No.4605,@ Wt 1.094 kg/Rmt ) with 3mm

thick bajari Figured Glass fixed to alluminium strip blade fixed or

louvers adjestable ventilation including all required materials, fixtures,

fastenning, labours and equipments as per detailed drawing as

directed. For V1

38 Providing & Fixing in position standard extruded approved colour 8.10 Sqmt 1811.94

anodised Aluminum Ventilator with outer frame 65 x 25 mm Stander

Box Frame(of Jindal Section No.4605,@ Wt 1.094 kg/Rmt ) with Wire

Mesh Jali ventilation including all required materials, fixtures,

fastenning, labours and equipments as per detailed drawing as

directed. For V

39 Providing and fixing rolling shutters of approved make made of 80 mm 42.80 Sqmt 3554.40

wide M.S. laths 1.25mm thick inter-locked together through their

entire length and jointed together at the ends by end locks mounted

on specially designed pipe shaft with bracket plates, guide channels

and arragements for inside and outside locking with push-pull

operation including the cost of hood cover and spring etc. complete.

(B) Shutters having width below 3.5 Mt

40 Providing and fixing in position collapsible steel shutters with vertical 342.00 Kg 67.67

channel 20 x 10x 2 mm braced with flat iron diagonals 20 x 5 mm size

with top and bottom rails of T_rin 40 x 40 x 6 mm with 38 mm dia,steel

pulleys complete with bolts,nuts,locking arrangements,

stoppers,handles including applying priming coat with two coats of

enamel paints etc. Complete.

41 Providing and fixing M S angle openable Double Shutter grilled Door 723.00 Kg 105.04

having 65 MM. x 65 MM x 6 MM size M.S. angled welded togather to

make a box frame and 20mm dia M.S. bars to be fixed with it by

drilling hole in the angle section and welded at 10 cm C/C approx

including anodized iron fixtures & fastenings including primer coat of

approved quality and two coats of oil paint etc., complet as per detail

drawing as directed.

42 Providing and fixing Glass Door of 3.00 x 2.85m of Double shutter 9.00 Sqmt 4098.58

16mm toughen glass with Floor Spring and Pivot with fixed side panels

and Fixtures and Required Fitting material and labour etc. complete as

per the drawing, detail specification or instruction of engineer in

charge. Door shall be providing with Floor spring Heavy duty and 60cm

long stainless steel handle and necessary Locking system of Godrej, S.S

fixtures & fastenings etc. directed by engineer in charge D

43 Providing and fixing 38 mm thick flush door Double shutter, solid core 20.20 Sqmt 4270.28

with Flushed Door Having Decorative 1mm thick laminates on both

sides & 12 mm T.W.Beading Around the Door and stainless steel

handle, S.S. Aldrop ,S.S. Handle ,S.S. Stopper and necessary Locking

system or S.S hinges ,S.S fixtures & fastenings etc directed by engineer

in charge D1,D2

44 Providing and fixing 38 mm thick flush door Single shutter, solid core 42.00 Sqmt 3748.11

with Flushed Door Having Decorative 1mm thick laminates on both

sides & 12 mm T.W.Beading Around the Door and stainless steel

handle, S.S. Aldrop ,S.S. Handle ,S.S. Stopper and necessary Locking

system or S.S hinges ,S.S fixtures & fastenings etc directed by engineer

45 Providing and fixing 35 mm thick water proof flush door Single shutter, 14.10 Sqmt 2955.26

solid core with Flushed Door Having Decorative 1mm thick laminates

on both sides & 12 mm T.W.Beading Around the Door and stainless

steel handle, S.S. Aldrop ,S.S. Handle ,S.S. Stopper and necessary

Locking system or S.S hinges ,S.S fixtures & fastenings etc directed by

engineer in charge D4 & D5

46 Providing and fixing 90 cm & 105 cm high Stainless steel railing made 80.60 Sqmt 3886.48

from anticorrocive 304 grade S S pipe of 50 mm dia (16Gauge) as hand

rail with S S 304 grade Baluster of 38 mm dia (16Gauge) as a vertical

support fixed in RCC slab at 0.30m c/c including Four horizontal S S

pipes of 16 mm dia (16Gauge) at eqal distance fixed including The

Provisions in Nation Building Code 2016, part,Annex:B-6.2 with

baluster ,accesies as per detailed drawing as directed etc. complete.

47 Providing and fixing 316 grade S S hollow pipe Hand railing into 10cm 25.70 Kg 563.58

thick & 100cm Hight RCC wall @ on top 50 mm dia (16Gauge)

horizontal pipe and vertical support railing with all material , laboure

charges and accessories requirement as directed by Engineer-in-

charge etc. complete.

48 Providing and laying machine cut Mirror polished Granite stone 188.70 Sqmt 2188.67

18mm thick finished treads , risers and Skirting in full length with

Polished Edges & Anti Skid Groove with 1cm projecting, nozing in

tread laid over 20 mm (av.) thick bases of cement mortar 1:6 (1-

cement : 6-coarse sand) jointed with grey or colour cement slurry

including rubbing and polishing etc. complete

49 Providing and laying Soluble Salt Vitrified Tiles of 8 & 10mm thick, 60 x 314.30 Sqmt 1531.82

60 cm in flooring, treads of steps and landing laid on a bed of 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

new surface or fixing on existing flooring by adhesive material and

jointed with color cement slurry including finised with flush pointing &

cleaning the surface etc. complete for Colour and Shade approved by

Engineer-In-Charge

50 Providing and laying Soluble Salt Vitrified Tiles Tiles of 8 & 10mm thick, 27.70 Sqmt 1592.40

60 x 60 cm in Dado, Skirting, treads of steps and landing laid on a bed

of 12 mm (average) base of cement mortar 1:3 ( 1 cement: 3 coarse

sand) on new surface or fixing on existing flooring by adhesive material

and jointed with color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for Colour and Shade

approved by Engineer-In-Charge

51 P & L 60x60 cm Hand Dressed Rough Kota Stone slab 30 mm thick 694.80 Sqmt 1121.80

flooring over 20 mm (average)thick base of cement mortar 1:6 (1-

cement 6-coarse sand) or L.M 1:1.5 (1 Lime putty : 1.5 coarse sand laid

over and jointed with grey cement slurry mixed with pigment to match

the shade of slab including rubbing and polishing etc.complete

52 P & L 60x60 cm Hand Dressed Rough Kota Stone slab 25 mm thick in 41.10 Sqmt 1205.60

riser of steps,skirting dedo and pillars laid on 10 mm thick cement

mortar 1:3 (1-cement 3-coarse sand) and jointed with grey cement

slurry mixed with pigment to match the shade of slab including

rubbing and polishing etc.complete

53 P & L 30x30 cm. Coloured Ceramic Anti-Skid Textured Tiles 6 mm thick 29.90 Sqmt 1070.50

in flooring treads of steps and landing laid on a bed of 12 mm thick

cement mortar 1:3(1-cement:3-coarse sand)finishing with flush

pointing in colour cement slurry etc. complete. Colour and Shade

approved by Engineer-In-Charge

54 P & L 30x45 cm. Coloured Glazed Tiles 6 mm thick in skirting risers of 251.90 Sqmt 1523.67

steps and dedo on 10 mm thick cement plaster 1:3 (1-cement:3coarse

sand) and jointed with colour cement slurry

55 Providing and laying water proofing treatment with broken china 944.00 Sqmt 779.70

mosaic flooring for terrace using 12mm to 20mm of broken piece of

ceramic glazed tiles (or more colour directed ) to be laied over cement

mortar bedding of cm 1 : 3 (1 cement 3 sand ) to blain or slope and to

be tempered to bring mortar ceramic up to surface with using white

cement and colour pigment including rounding of junction extending

them up to 15cm along the wall and caring with bends any patten or

design on per drawing and clennig by using oxalic acid etc. Completed

56 Providing and fixing pre-cast Rubber Dye inter locking concrete block 196.90 Sqmt 707.55

60mm thick with grade of concrete M300 Pg.Noumatic

compressed/Vibrated mechanically and as per approved design

confieming to IS 15658: 2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and level as per guidelines

of IRC : SP 63-2018 etc complete.

57 Providing and fixing Mirrar polished 18 mm thick Granite stone in 185.30 Sqmt 2298.76

Single piece with edge finished and polished of approved quality in

clading on Cill & Jambs and around the doors/ windows/ ventilation

with 12 mm thick cement motor CM (1:4) and fixing with cement slurry

& adhesive including moulding of exposed edges as directed by

engineering in charge etc. complete.

58 Providinfg and fixing Safty grills of required pattern for windows/ Door 1360.80 Kg 116.15

using necessary 12mm M.S Round/ Square bar /M.S angle/ M.S pipe,

M.S flats and other structural steel at required spacing including

cutting, welding and fabriction etc. including one coat of primer of

approved quality and two coats of oil painting as per detail drawing etc

59 Providing erecting and fixing double coated Syntex PVC. (ISI) water 10000.00 Litre 3.95

tank of required capacity each with all necessary fittings and

connection etc. complete on terrace.

60 Providing laying and jointing in true line and level 50mm dia. U.P.V.C. 60.00 Rmt 195.67

Pipe ( SCH- 40) for cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

61 Providing laying and jointing in true line and level 40mm dia. U.P.V.C. 50.00 Rmt 148.12

Pipe ( SCH- 40) for cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

62 Providing laying and jointing in true line and level 25mm dia. U.P.V.C. 70.00 Rmt 91.84

Pipe ( SCH- 40) for cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

63 Providing laying and jointing in true line and level 15mm dia. U.P.V.C. 70.00 Rmt 72.65

Pipe ( SCH- 40) for cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing of pipe and joints and

fixing the same with adhesive solvent, including cost of all materials.

64 Providing, laying and jointing in true line and level 160 diametre 345.00 Rmt 834.38

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on

wall using of PVC clamp of the size 160 mm diametre x 210 mm length

x 196 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

65 Providing laying (to level or slopes) and jointing reinforced concrete 80.00 Rmt 678.03

Light duty non-pressure pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for collar joints including

testing of joints complete.(D) 300mm

66 Providing, laying and jointing in true line and level 110 diametre 25.00 Rmt 897.79

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain and

other end socketed with rubber ring, & fittings conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on

wall using of PVC clamp of the size 110 mm diametre x 149 mm length

x 145 mm heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

67 Providing, laying and jointing in true line and level 75 mm dia. UPVC 25.00 Rmt 765.58

SWRType B pipe conforming to IS 13592-1992 with one end plain and

other end socketed with rubbering and fitting conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on

wall using of PVC clamp at every 2000 mm c/c or shall be conceled in

walss as directed including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

68 Providing and fixing in PVC SWR cowel went 75mm dia to pipes.(B) 5.00 No 15.15

69 Providing and fixing in PVC SWR cowel went 110mm dia to pipes.(B) 5.00 No 27.27

70 Providing and fixing MS Z clamp on Wall or celling for Pipe Fitting 173.00 No 70.70

including all type necessary fittings and accessory etc. completed as

per directed engineer in charge.

71 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 20.00 No 600.23

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of

cutting and making good the walls.

72 Providing and fixing wash down water closet dual flushing system type 5.00 No 4141.00

(European type W C pan) with integral P and S trap including jointing

the trap with soil pipe in cement mortar 1:1 (1 cement five sand)

including providing and fixing plastic seat cover for wash down WC

with CP brass hinges and rubber buffers back plastic seat and 60 cm

long Heavy Duty Jet Spray including half turn flush cock dual flushing

system including cutting holes in walls and making good the same

connection the flush bend with cistern and closet vitreous china.

73 Providing and fixing ball cock of approved. quality as directed.(A) 2.00 No 189.84

Copper Metal (ii) 50mm dia.

74 Providing and fixing washbasin with single hole for pillar tap with C.I. 5.00 No 1486.04

or M.S. brackets painted white including sutting holes and making

good the same but excluding fittings.(A) Vitreous China:(ii) Flat Back

washbasin 550 mm x v 400mm size. (i) In white colour.

75 Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mm 17.00 No 67.91

76 Providing and fixing M.I. fisher union for washbasin or sink. (A) 32mm 17.00 No 78.75

77 Providing and fixing 600mm x 450mm bevelled edge mirrror of 5.00 No 859.41

superior glass mounted on 6mm thick A.C. sheet or plywood sheet and

fixing to wooden pluge with C.P. brass screws and washers.

78 Providing and fixing C.P. brass towel rail comlete with C.P. brass 5.00 No 616.42

brackets fixed to wooden plugs with C.P. brass scews (B) 600mm x

79 Providing and fixing screw down bib taps of following size.(A) Brass 22.00 No 186.83

screw down bib tap polished bright. (i) 15mm dia.

80 Providing and fixing pillar tap, capstan head, screw down high pressure 17.00 No 308.73

with screws, shanks and back nuts. (i) 15mm dia.

81 Providing and fixing brass screw down stop tap.(A) 15mm dia. 20.00 No 205.83

82 Providing and fixing brass screw down stop tap.(C) 25mm dia. 5.00 No 220.82

83 Providing and fixing Gun metal check or non-return fullway wheel 5.00 No 663.43

valve.(E) 40mm dia.

84 Providing and fixing S.W. gully trap with C.I. grating brick masonry 6.00 No 1246.92

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight (i) Square mouth traps (B) 150mm x

100mm size P or R type

85 Constructing brick masonry chamber for underground C.I. Inspection 5.00 No 3196.65

chamber and bends with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 precast RCC cover 455mm x 610mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size) foundation

concrete 1:5:10 inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on walls and bed

concrete etc. complete (i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

86 Constructing brick masonry chamber for underground C.I. Inspection 5.00 No 3905.67

chamber and bends with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc. complete.(i) Inside

dimensions 500mmx 700mm and 450mm deep for single pipe line.

87 Extra over items for every additional depth of 0.1M. of part thereof 3.00 No 242.39

beyond 450mm depth for Brick masonry chamber.(i) for 455mm x

88 Extra over items for every additional depth of 0.1M. of part thereof 3.00 No 264.86

beyond 450mm depth for Brick masonry chamber.(i) for 500mm x

89 Providing cement vata (10cm x 10cm size) quarter round in cement 168.40 Rmt 24.28

mortar 1:1 including neat cement finishing watering etc. Complete

90 Providing and fixing Urinal or approved quality including conecting the 3.00 No 1074.86

Urinal with waste pipe , tap etc. complete.(A) White earthenware flat

back or corner type size 430mm x 260mm x 350mm.

91 Providing and fixing MS Ladder of required pattern with MS 100.00 Kg 115.14

flats(30x3mm) or round or square bars (12mm) at required spacing &

with round headed bolts and nuts or screws or welding including

primer coat of approved quality and two coats of oil paintas as

directed by engineer in charge

92 Providing and fixing polished 18 mm thick black granite with Edges 1.40 Sqmt 2061.41

finished and double side polished of approved quality in between

urinal and fixing with cement slurry & adhesive including moulding of

both exposed edges as directed by engineering in charge etc.

93 Providing and fixing 0.45 meter wide sand which type wash counter 0.60 Sqmt 3287.55

platform including supplying and fixing granite stone of 18 mm thick

mirror polished on top and side posiition and vertical strip at front

with cement slurry & adhesive including moulding of both exposed

edges over 25 mm thick kotah stone platform fixing in top and sides

and itermediates supports fixing with cement mortar and adhesive and

finishing with C.P. brass waste , M.I. fisher union,pillar tap,Rubber plug

all material and labour and assessories complete etc.

94 Constructing Sandwitch Platform of 18 mm thick Polished Black 21.00 Sqmt 2740.13

Granite at top and 25 mm thick Kota stone slab one side polished at

bottom with cementing Materials / adhsives including makeing

necessary grooves in walls with Vertical sandwich two Kotastone

mm support every 60 cm centre to centre or as required including all

labour material of approved quality incl. full moulded round front

edge granite strip of one side polished and jointed with grey cement

slurry including rubbing and polishing etc. complete for all floors

95 Providing and fixing in position 300 mm high, 150 mm wide 150.00 No 707.00

English/Gujrati letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools & plants etc.

96 Providing and fixing of Ridge flashing for roof panel shall be made out 133.70 Sqmt 867.39

of 0.5 mm thick pre coated GI sheet . The Precoated sheet shall be of

minimum 240 mpa steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet and polyester top coat

15-18 micron. The PPGI Sheet shall have plastic protective guard film

of minimum 25 microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by pop rivet or self

drilling/self stitching fastners @ maximum 450 mm c/c along length of

capping/flashing etc complete.

97 Steel work, welded in built up sections framed work including cutting, 2673.00 Kg 91.08

hoisting, fixing in position and applying a priming coat of read lead

paint & two coat oil paint. (A)In beams and joists, channels angles

Tees, flats, with connecting plates or angle cleats as in main and cross

beams. Hip and jack rafters, purlins conneted to common rafters and

98 Providing and Fixing 15 mm thick 300 mm x 300 mm Tactile Warning 7.20 Sqmt 1228.16

Tiles (Attention Tiles i.e. Tactile Warning Surface Indicator {TWSI}) of

Johnsan Endura Tac Button Yellow Plus or equvqlent make in flooring

laid on 20 mm thick cement mortar 1:6 (1 cement : 6 coarse sand) on

new surface and jointed with cement slurry including finished with

flush pointing & cleaning the surface for all floors as per detailed

drawing etc. complete as directed by Architect or Engineer in charge.

Thse tiles shall be Anti Skid, Chemical Resistant, Fade Proof, Frost -

Heat & Weather Proof, High Flexural Strength, Highly Durable, Stain

Resistance . All Tactile Warning Tiles meet the specific size and

dimension standards as required by ISO/FDIS

99 Providing and Fixing a set of wall mounted 38 mm dia U shaped 1.00 Per 2555.30

horizontal stainless steel collapsible grab bar , 38mm vertical stainless Set

steel fixed grab rail of grade SS 304 from round pipe supported and

mm dia 8 mm thick SS 304 base flange on wall including anchor

fasteners, nuts, accessories as per detailed drawing etc. complete as

directed by Architect or Engineer in charge.

100 Providing upto floor two level precast cement concrete jali or grill 1:2:4 101.50 Sqmt 759.59

mix (1- Cement : 2- coarse sand : 4-graded stone aggregate 6mm

nominal size) reinforced with 1.6 mm dia. Mild steel wire including

roughening,cleaning, fixing and finishing in cement mortar 1:3 and

curing complete. (C) 25mm thick

101 Providing and laying and fixing 50 mm thick expansion joint by hydro 19.10 Sqmt 1491.03

cell semi rigid UV resistance with high performance laminated closed

cell polythene foam joint filler in sheet foam as directed, etc.

102 Applying and providing Expansion joint sealing System on 100 mm vide 19.10 Sqmt 4772.00

joint including cleaning of exansion joint by mechanical means

provision of adhesive and flexible membrane with required bond

length as per menufracturer specification and 4mm thick alluminium

strip covering with one side sloted and bolted with suitable system,

inclusive of all manpower, machinery and material as per specification

and as directed.

103 Providing and filling the expansion joint by Thioflex 600 polymer or 19.10 Sqmt 515.39

equivalent confirm to BS 4254-1983 as per required shade and

manufactured specifi-cation by making groove of 50 mm x 12.5 mm

lather by cutting or by repairing groove and removing mortar drop or

any other foreign materials including applying primer and filling

required size (oversize of joint PU foam etc. complete.

104 Providing and fixing 25 cm Wide & 3mm thick exterior composite panel 19.10 Sqmt 1054.34

on existing expansion joint horizontally & vertically with all material,

hardware, acessories & fittings etc completed.

105 10mm Rebar, excluding bar. It should minimum 100mm embedded in 80.00 Nos 114.13

concrete, drill dia. Should be minimum 18mm for rebar, material

should be used Will Fischer FISV 360 or equievalent. (Pull out strength

check should be given by contractor as per technical specifications)

106 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working 280.00 Rmt 339.05

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(G)110 mm

107 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working 50.00 Rmt 689.83

pressure poluthene pipes of the following outside Dia. Low densidy,

complete with special falnge compression type fittings, wall clipsetc.

including making good the wall ceiling and floor.(G)160 mm

108 Providing junction for rain water juncton chamber of size 4.00 No 6613.48

0.60x0.60x0.75m with excavation of size 1.96x1.96 m & 0.15m thick

c.c.1:2:4 bed concrete including brick masonary wall in CM 1:6 of

0.75m height & 0.23m thick with 15mm thick cement plaster inside &

outside & 1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS steel

and 0.60mx0.45m cast iron manhole cover with frame weight not less

than 35 kg as per directed by Engineer-in-charge

109 Providing Filter chamber of Brick work in C:M 1:6 of size 2.06mx1.20m 1.00 No 19572.79

x1.20m & excavation dimension of 2.82mx 1.96x1.35m including C.C

1:2:4 bed concrete of 0.15m thick including brick work in c.m 1:6 for

23cm thick wall including 15mm thick cement plaster inside & outside

with cement slurry & 10cm thick RCC 1:2:4 top cover with frame of

minimum weight of 35 kg & filling filter material kapchi in layers (25-

40mm & 10-20mm) & BT metal 40mm & sand as per directed by

Engineer-in-charge.

110 Drilling in soil with lowering of pipes concrete sealing including gravel 30.00 Rmt 545.40

packing clay breaking and development of bore with air compressor by

required capacity vertical test etc. complete including the cost of

benimeter 250mm dia.

111 Supplying slotted PVC pipes of approved quality at site of work 30.00 Rmt 555.50

confirming to IS. 1239/1974 180mm dia.

112 Constructing brick masonry chamber for underground C.I. Inspection 1.00 No 7180.44

chamber and bends with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions, total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of

neat cement on walls and bed concrete etc. complete.(iii) Inside

dimensions 600mm x 850 mm and 450mm deep for pipe lines with

three or more inlets.

113 Box cutting the road surface to proper slope and camber for making a 164.00 Cumt 112.02

base for road work including removing the excavated stuff and

depositing on the road side slope as directed upto 50Mt.lead.

114 Construction of granular sub-base 150 mm thick by providing coarse 55.00 Cumt 1282.70

graded machine crushed B.T. material satisfying MOST specification of

grading I (B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to

mm - 45 % and 2.36 mm below - 20 % )including spreading in uniform

layer with motor grader on prepared surface, mixing by mix in place

method with rotavator at OMC and compacting with vibratory roller to

achieve the desired density etc. complete.

115 Providing and laying wet mix macadam base course 200 mm thick 73.00 Cumt 1335.22

using machine crushed B.T. chips as per required gradation mixing with

required optimum quantity of water, conveying the mix to site of

work, spreading in to grade and camber with mechanical paver and

consolidation each layer with vibratory roller including cost of material

labour plant and equipment etc. complete.

116 Providing and laying controlled cement concrete M.150 and curing 44.00 Cumt 3898.54

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in (A) Foundations and

117 Providing &laying ave. 200 mm thick M-250 grade of controlled 73.00 Cumt 5826.69

cement concrete including dressing sub base providing and laying

micron thick LDPE memberance over prepared sub base providing and

mixing recron 3s fiber at 875 gm/cmt. of concrete placing the concrete

and leveling with surface vibrator finishing the surface with power

floater and trowel light brooming on the surface as directed including

Providing and filling exparsion joint having size 20 mm x 115 mm &

filling the expansion joint having size 20 mm x 20mm by using cloper -

200 as per manufacturer's specification and making construction joint

having size 10 mm x 10mm by using concrete cutter machine etc.

Providing and fixing pre-cast concrete kerb stone of gray cement based 140.00 Rmt 374.92

concrete block 30cm length,30cm height and 15cm thick of M250

grade concret as per approved design and including excavation for

fixing in proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

119 Providing, laying (to level or slopes) and jointing reinforced concrete 47.00 Rmt 659.99

Light duty non-pressure pipes I.S. class NP3 of the following internal

diameter with collars and butt ends prepared for collar joints including

testing of joints complete. (i) 300mm

120 Clearing and grubbing road land including uprooting rank vegetation 0.62 Hrct 28455.10

grass bushes, shrubs, sapling and trees girth up to 300 mm removal of

stumps of trees cut earlier and disposal of unserviceable materials (C)

By mechanical means in area of light jungle

121 Earthwork for embankment including breaking clods, dressing with all 6655.00 Cumt 173.31

lead and lift (excluding watering and consolidation)(E) From Borrow

area within 3.0 Km. lead

122 Rolling of earthwork in layers with power roller including filling in 6655.00 Cumt 23.18

depressions which occur during the process and Watering of earth

work as directed.

123 Excavation for foundation up to 1.50 Mt. Depth including sorting out 108.00 Cumt 160.89

and stacking of useful materials and dispossing on the excavated stuff

upto 50 M. lead ( B ) Dense Or Hard soil

124 Providing and laying cement concrete 1 : 4: 8) (1 cement : 4 coarse 36.00 Cumt 2781.12

sand : 8 stone aggregate 40 mm nominal size ) and curing complete

excluding cost of formwork in foundation and plinth.

125 Providing and laying weep hole in Aburtments, and returns by using 47.00 Nos 88.76

A.C. pipe of 100mm including laying in proper grede and jointing the

completed as per detailed specification.

126 Providing and fixing decorative entrance gate made out of cast iron 480.00 Kg 124.23

and various mild steel tabular section combination , the Ornamental

entrance gate should be fixed at compound wall including pattern and

die making , cutting , welding , grinding, fabrication , fixing in position

at compound wall with necessary pedestal, bearing block and other

locking arrangement. The entrance gate should be painted with two

coats of priming coat of paint, and two coat of oil paint etc complete.

As per detail design and instruction of architect.

127 Providing and fixing concertina coil fencing with punched tape 60.00 Rmt 349.46

concertina coil 600 mm dia 10 mt openable length having 50 no

rounds per 6 mt length, upto 3mt height of wall with angle iron (50mm

x50mm x5mm) requird shaped As per Directed Engeenier in charge.

placed 2.4mt or 3.00mt apart and with 4 horizontal R.B.T. reinforced

barbed wire(3 mm) , stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or G.I.barbed wire tied to angle

iron, all complete as per direction of Engineer-in-charge, with

reinforced barbed tape (R.B.T.)/Spring core (2.5 mm thick) and weight

43.478 gm/meter at compound wall for ESR M4/ intakewell.

128 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 213.00 Pt. 485.81

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push & accessories and

earth continuity of following type, erected on PVC / Metallic/Wooden

box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat. III

129 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 57.00 Pt. 674.68

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step type electronic

fan regulator mounted and accessories with earth continuity of

following type erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured/metallic/white front

plate modules erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed. (f) with medium

class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat. III

130 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) 26.00 Pt. 510.05

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules

erected on / in wall / ceiling as per pipe erected with following type of

accessories. [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire

from nearby switchboard/mcb db board (f) with medium class Rigid

PVC pipe and accessories erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) 19.00 Pt. 745.38

both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected

complete with Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate modules

erected on / in wall / ceiling as per pipe erected with following type of

accessories. [II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.

Wire from mcb db board. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Ca-III

132 Point wiring for on board Looped Plug with 6A Modular type switch & 33.00 Pt. 257.55

5 pin socket erected on PVC / Metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following type accessories

133 Providing following type of Modular Type Accessories mounted with 16.00 Nos 160.59

PVC / metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.(3)

Two Pin/RJ-11 Telephone Socket[A] For One GangCat.III

134 Providing following type of Modular Type Accessories mounted with 10.00 Nos 25.25

PVC / metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.(7)

Blank Plate Single.Cat-III

135 Providing following type of Modular Type Accessories mounted with 20.00 Nos 160.59

PVC / metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.(8)

Computer RJ-45 socket Cat.III

136 Providing following type of Modular Type Accessories mounted with 10.00 Nos 410.06

PVC / metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge.(14)

6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch Ca-III

137 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 1110.00 Mtr. 24.24

following size complete to be erected on/in wall or ceiling erected

with necessary PVC fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in approved manner as

directed (a)20 mm

138 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 795.00 Mtr. 82.82

marked stranded Copper conductor wire in following type of pipe to

be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size(A) With medium class Rigid PVC pipe

and accessories(b) 2 wire 2.5 sq. mm

139 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 40.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to

be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of

following size(A) with medium class Rigid PVC pipe and accessories (a)

2 wire 4 sq. mm

140 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 140.00 Mtr. 260.58

marked stranded Copper conductor wire in following type of pipe to

be erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS

PVC insulated stranded wire of green colour for earth continuity of

following size(A) with medium class Rigid PVC pipe and accessories(h)

4 wire 6 sq. mm

141 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte 60.00 Mtr. 91.91

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears,

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required.(f) One wire 10.00 sq. mm

142 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte 30.00 Mtr. 236.34

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears,

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required.(h) One wire 25.00 sq. mm

143 Supplying and erecting Flexible PVC insulated multi strand multi core 60.00 Mtr. 46.46

1.1 kv grade ISI marked copper wires of following size to be erected as

directed.(e) 1.50 Sq.mm 3 core round PVC sheathed

144 Supplying & erecting approved make Telephone Cable electrolytic 560.00 Mtr. 20.20

copper conductor PE insulation twisted in two pairs, & wrapped with

FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable

for telephone wiring & confirming to C-DOT erected in existing pipe. of

following size of conductors & nos.of pairs. With necessary

connections.[A] Conductor Size 0.5 mm (a) Unarmoured(2) Two Pairs

145 Supplying & erecting approved make LAN cable of following size in 750.00 Mtr. 47.47

existing pipe as per direction[C] CAT -

146 Providing & erecting main Distribution (MDF) indoor type, back 1.00 Nos. 994.85

mounted frame as per DoT standard approved with krone strips(a)

Suitable for 10 pair

147 Providing & erecting Switch board for Computer or electric apparatus 20.00 Nos. 1133.22

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered

with textured/metallic /white front plate,modules erected with

necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories

148 Decorative call bell Ting-tong box type 250 volts complete erected 8.00 Nos. 71.71

149 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 195.00 Nos. 535.30

Watt to 0.5 Watt assembled on single MCPCB, with housing used as a

heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt, LED driver efficiency > 85 % (

fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges

shown.)(A) Tube Light with integral driver(v) 36-40 Watts, Surge-2 KV,

IP-20, conventional 4 feet Cat-III

150 Supplying and erecting led lamps with following wattage capacity of 4.00 Nos. 112.11

220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-

surge protection,Polycarbonate diffuser, mounting suitable for E14 /

E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (ii) 5 to 8 watts Cat-III

151 Replacing old & u/s led streetlights by Supplying and erecting LED 12.00 Nos. 3345.12

street light / Flood light fittings with High power White LEDs wattage

of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80 certificates)(old -50 ,new -

20(NOTE: Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)(A) Street Light (IP-65), Surge protection -

4KV integral and ,Light must have 440VAC line supply with over-

voltage protection. (i) above 36 to 48 watts Cat-III

152 Replacing old & u/s led streetlights by Supplying and erecting LED 4.00 Nos. 7266.95

street light / Flood light fittings with High power White LEDs wattage

of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80 certificates)(old -50 ,new -

20(NOTE: Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)(B) Flood Light (IP-65), Surge protection -

4KV integral and ,Light must have 440VAC line supply with over-

voltage protection. (iv) above 90 to 120 watts Cat-III

153 Replacing old & u/s led streetlights by Supplying and erecting LED 4.00 Nos. 4819.72

street light / Flood light fittings with High power White LEDs wattage

of 3 Watt and above assembled on single MCPCB, efficiency more than

130 lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium

with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80 certificates)(old -50 ,new -

20(NOTE: Below description have shown ranges of Wattage capacity of

LED fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)(C) Post Top Lantern LED fitting comprises

of finish cast aluminum spigot and spun aluminum canopy fixed with

opal polycarbonate, pipe arrangement for vertical mounting driver and

accessories wired upto terminal block.IP 65(ii)32-40W Cat-lll

154 Providing and erecting Approved make Four pole moulded case circuit 1.00 Nos. 8055.76

breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

155 Providing and erecting Approved make Four pole moulded case circuit 1.00 Nos. 8861.34

breaker having breaking capacity ICU of 35 KA. at 415 V. having normal

current rating 125A. with Fixed thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in with 16 G.M.S. housing.

ICS=100% of ICU only Cat III

156 Providing and erecting Approved make Four pole moulded case circuit 9.00 Nos. 6173.12

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected in existing

G.M.S. housing.

157 Providing and erecting Approved make Earth fault Relay suitable to 1.00 Nos. 4983.34

mount with inter connection suitable to following size of moulded

case circuit breaker having CT ratio & MCCB rating as following along

with shunt trip 220V AC. with all internal connections & complete

erected in existing M.S.housing.. (2) 125 A -200 A , CT Ratio 1/200

158 Supplying and erecting triple pole & neutral 440V / 500V panel 1.00 Rmt 1961.42

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current

/ cross section area) duly wrapped with colour insulating tape for

phase sequence of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary connections.(A)

Suitable for 100 Amp. Capacity

159 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A 20.00 Nos. 270.68

system and having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat.III

160 Providing and erecting Miniature circuit breaker single pole 6A to 25A 72.00 Nos. 112.11

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

161 Providing & erecting 240 V MCB double pole switch for motor & 4.00 Nos. 330.27

inductive load (C Curve) having 10 KA breaking capacity & confirms

to IS : 8828 in existing box having following capacity (B) 40 Amp.

162 Providing and erecting Sheet Steel powder coated MCB distribution 4.00 Nos. 2913.85

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for(B) three phase

incoming and single phase horizontal type outgoing Per phase

isolation type (PPI)(b) sheet steel double door(ii)6 way

163 Providing and erecting Approved make RCCBs conforming to IS: 12640 13.00 Nos. 2235.13

and having sensitivity of 30 mA and Short Circuit withstand capacity of

10 KA and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do

not incorporate any electronic component. for following Max. rating

erected as directed(ii) 40Amps. DP Cat. III

164 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 30.00 Kg. 77.77

165 Providing and erecting Pipe type earthing having 150 cms.long and 2.5 3.00 Nos. 368.65

cms. dia. galvanised iron pipe with coupling and buch buried in

specially prepared earth pit complete with necessary 8 SWG earth

166 For using salt and charcoal / coke as required for pipe type earthing. 3.00 Nos. 171.70

167 Supplying & erecting earth pit of minimum bore dia.150mm size 2.00 Nos. 4591.46

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the

value of earthing resistane mentioned in test Certificate) & having back

filling compound of (a) For Electrical Installation up to 440V in normal

Length of pipe - 1 Mtr

168 Back filling&compound

Providing - 1 Nos proof,

erecting weather Bag of dust

& vermin proof, floor 2.00 Sqmt. 10468.65

mounted front operated indoor type cubical panel board necessary IP-

42 and above protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body & doors,

SWG thick CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal partitions & cable alley

as per requirements & instruction of engineer-in-charge with erection

of supplied switch gears, BUSBARS, suitable size of inter connecting

PVC copper wire / copper-aluminium strips, rubber grommets, rib,

bakelite control fuses/MCB for measuring instruments, earth bus &

earth bolts, foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and rubber

gasket,heavy duty end terminal connection,danger notice

board,necessary ventilation,earthing strip complete. The Panel shall

be painted with epoxy powder coating. (The rates excludes the cost of

switchgears, bus bars, inter connecting mains & Copper Aluminium

169 Providing , erecting , fabricating the M.S. structure as per requirement 25.00 Kg. 77.77

on site incorporating proper size of M.S. angles,square,round, flats,

bars, channels, sections complete with cutting, welding, grinding &

finishing duly painted with one coat of red oxide with erection on site

as per direction of engineer in charge with necessary grouting,

cementing, plastering & finishing complete.

170 Providing and erecting XLPE(IS:7098) (I)-88 ISI armoured cable 50.00 Mtr. 378.75

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core)

171 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 450.00 Mtr. 126.25

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size of

cables(B) 4 core 6 Sq. mm

172 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 50.00 Mtr. 140.39

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of

cables(C) 4 core 10 Sq. mm

173 Making trench in soft soil of suitable width of 90 cm deep for laying 450.00 Mtr. 55.55

cable or locating the fault all over the run and back filling the same

and making the surface as normal ground.

174 Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm. below 40.00 Mtr. 226.24

ground across the road crossing or on floor with necessary material in

an approved manner and making the ground as per original.(F)

175 Providing & laying approved make Double walled corrugated pipes 410.00 Mtr. 62.62

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

connecting accessories of same material at required depth in existing

trench for laying of cable. below ground / road surface for enclosing

cable (A)50 mm outer dia

176 Providing and, fixing heavy duty flange type brass cable gland with 18.00 Nos. 38.38

rubber ring for PVC insulated armoured cable complete with out going

tails, insulating tape etc for following size of cables.(B) 2 to 4 core 6 Sq.

177 Providing and, fixing heavy duty flange type brass double compression 2.00 Nos. 75.75

type cable gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for following size of

cables.(B) 3 & 1/2 core 35/50 Sq. mm

178 Providing and, fixing heavy duty flange type brass double compression 6.00 Nos. 103.02

type cable gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for following size of

cables.(C) 3 & 1/2 core 70 Sq. mm

179 Solder less crimping type Aluminium lugs conforming to IS suitable for 36.00 Nos. 6.06

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

180 Solder less crimping type Aluminium lugs conforming to IS suitable for 2.00 Nos. 20.20

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (D) 35/50 Sq.mm.

181 Solder less crimping type Aluminium lugs conforming to IS suitable for 6.00 Nos. 25.25

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (E) 70 Sq.mm..

182 Providing & erecting Approved make Ceiling Fan with double ball 57.00 Nos. 1738.21

bearing ISI mark with condenser A.C.230V 50c/s. 1400 mm. sweep

complete, canopy erected on existing hook or clamp with earthing [

Make shall be approved by Engineer in Charge]

183 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. 57.00 Mtr. 108.07

Pipe down rod erected duly painted for fan complete with proper

insulation without leakage and earthing.

184 Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in 57.00 Nos. 43.43

RCC slab with Making the site as original.

185 Supplying & erecting approved make low noise decorative exhaust fan 6.00 Nos. 1703.87

having square frame ABS body with inbuilt lowers & square

frame.200mm with 1350RPM Cat.II

186 Supplying and erecting approved make Octagonal pole made from HR 9.00 Nos. 6874.06

sheet steel. The pole should be made as per IS. and shall be coated

with hot dip galvanizing as per IS 2629/2633/4759, suitable suspend

local wind speed with integral Junction box consist of terminal plate of

min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for cable

termination to be erected With Suitable foundation (Included) as per

details given by manufacturer considering site requirement.(D) 5 Mtr.

Long 70 mm Top X 135 mm bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts and 600mm long with

necessary G.I. J Bolts .Approx Pole weight 59 kg

187 Supplying & erecting approved make SMC press moulded composite 8.00 Nos. 476.72

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.(C)150mm x 125mm x

188 Supplying and erecting Street light pole bracket comprising main B 10.00 Nos. 476.72

Class GI pipe of 4.2 cm/require outside dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts for fixing

the brackets and having spread of 0.5 mtr. Length with 110 deg.with

vertical plane and suitable welded stiffener reducer and nipple with

check nut complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint with following

nos of arms.[A] Single Arm bracket 0.5 Mt

189 Supplying and erecting Street light pole bracket comprising main B 3.00 Nos. 622.16

Class GI pipe of 4.2 cm/require outside dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and bolts for fixing

the brackets and having spread of 0.5 mtr. Length with 110 deg.with

vertical plane and suitable welded stiffener reducer and nipple with

check nut complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint with following

nos of arms.[B] Double Arm Bracket 0.5 Mtr

190 Supplying & erecting IP 55 grade following size section pillar fabricated 1.00 Nos. 3595.60

from joint less M.S. Sheet with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground to have appropriate

erection to work uniform until erected with cement concrete

foundation and 45 cm high bricks work finishing with plaster etc.

hinged double door internally supported on both side, with internal

and outside looking arrangement with look and keys in duplicate 35 x

35 x 5 mm M.S. Angle of Two Nos. one is welded and other with nut

and bolt for erecting Bakelite sheet. Painting the Section Pillar inside

and out side with three tank powder coated paint. section pillar roof

should be without joint with water leakage proof & tested as per IP

test & followed by IS 2147 of 1962(B) 75 X 60 X 45 cm section pillar

fabricated from 16 Gauge MS Sheet with angle iron legs 45 cm long

made from 35 X 35 X 5 mm thick MS angle.

191 Supplying & erecting approved make Digital time switch having lithium 1.00 Nos. 3168.37

cell 6 years operative and operate battery backup 1 channel day clock

with 14 memory programme, suitable to operate on 240V + 5%, 16A

with, floating contacts Minimum switching setup time 1 minimum &

LCD display. Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof thermoplastic enclosure

& transparent cover erected as required with necessary connection

erected as directed.

192 Supplying & erecting power contactor ,AC3 duty for time switch 1.00 Nos. 2782.55

complete erected as per direction Cat III (D) 4 pole 440V 40 Amp.

193 SITC of Digital / PCM / TDM EPABX System having SMT design, system 1.00 Nos. 51440.31

with flexible universal slots. Inbuilt Auto attendant facility, Minimum

15 Nos. conference, Analog extension line, Calling GSM, E&M line, PRI

/ EI & VOIP program me through Analog telephone digital key from

Ethernet, public address cord, shall have unrestricted simultaneous

dialing facility, QSIG protocol on PRI, 95 / STD / ISD / Local-Locking,

Class of Service, Quick Dial-Single Digit dialing of any two external

number, Once only ring device, Chairman / Secretary - Do not disturb

Facility, Power Down Mode, Hot Line, Hot Outward Dialing, Day Night

Mode, Auto Call Back, Barge-in, Call Pick Up & Call Transfer, Call

transfer while Ringing with Voice Guide System, (DISA), Caller ID (CLI),

CLI Base ECF, CLI Base routing Internet Ready Port, External Music Port,

Call Budgeting, Call Most Calculation (ASMDR), DID Direct Inverse

Dialing, External Music Input, Fax Homing, Global Directory Printing

with following capacities [[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ][B] No of Extension 24, No of

Junctions 9, 8 Port IP Resource in-built, 4 Port Web base Video

194 Supplying & erecting push button type telephone instrument having 13.00 Nos. 898.90

speaker phone Caller ID & speaker phone with one touch memory

(min.6 nos.)& 99 memories with display system Single line [[Approved

by Competent Authority i.e. not Below the rank of Executive Engineer ]

195 Providing and erecting Inverter based approved make split air- 5.00 Nos. 56353.96

conditioning unit consisting of condensing unit with variable speed fan

motor, inverter type hermetically sealed rotary compressor with

accessories etc. duly connected separately erected evaporating unit

196 Supplying and erecting insulated pair of soft copper tubing open or 35.00 Rmt. 746.39

concealed including power and control cable,necessary PVC drain

pipes for Split AC machine up to 4 TR capacity

197 Supply and Erecting of Static Stabilizer suitable for following capacity 5.00 Nos. 4029.90

of A.C Machine the Stabilizer Must have Minimum Technical

Specification are Input working Single Phase Voltage Range Up to 150V-

280V.50Hz, Output Voltage Range Up to 200V-240V,50Hz,Autoreset

198 Providing & erecting water cooler having storage capacity 150 Ltr. & 1.00 Nos. 55893.40

cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The

outlet temp. of the water should drop by 15˚C within a hour, The

water cooler should be comprising of hermetically sealed compressor,

fan motor, condensing unit, water tank surrounded by evaporating,

coil, thermostats, relay etc.complete with necessary inlet & outlet

connection. The body of water cooler will be made from Stainless

199 Supplying & erecting reverse osmosis (RO) water purification system 2.00 Nos. 55893.40

with M.S. powder coated pedestal frame, prefilter housing carbon

filter suitable buster DC pump, auto low & high pressure switches with

following size of LPH capacity & erected as directed [C] 50 Ltr / Hr with

150 psi 2 nos booster pump

200 Supplying and erecting horizontal / vertical mounting type storage 1.00 Nos. 11455.42

water heater with copper container housed in M.S./S.S./ABS body

insulated with glass wool/puff complete with heating

elements,adjustable thermostats 300C to 850C, indicating lamp,

safety valve, fusible plug, etc.complete erected with coach bolts, nuts.

washers & cementation (C)25 Ltr. with 2 KW. heating element

Premium Category

201 Supplying and erecting approved make panel mounting type Digital 1.00 Nos. 1275.63

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

202 Supplying and erecting approved make panel mounting type Digital 1.00 Nos. 1558.43

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

203 Supplying and erecting Ammeter / Voltmeter selector switch for 3 1.00 Nos. 317.14

phase AC Supply 500 V on existing panel board with necessary

204 Providing & erecting L.T. Current Transformer with bar primary 50/5 1.00 Nos. 274.72

to 1000/5 ratio 15 VA burden erected in existing CRCA box duly

secured with insulating materials connected to the meter

205 Supplying and erecting approved make suitable panel indicator LED 3.00 Nos. 43.43

type lamp, lens cover, complete erected with necessary connections.

206 Providing & erecting open well horizontal mono block pump set with 1.00 Nos. 18746.61

cast iron body, complete for three phase submersible motor

having.[D] For 5 HP 3 phase open well horizontal mono block pump set

suitable for 1350 LPM to 310 LPM @ 10 to 42 Mtr head suitable for

50/65 mm dia delivery pipe.Cat.II

207 Supplying and erecting Direct-on-line, Starter with 15A.rating 1.00 Nos. 2046.26

contractor and with 4-14A. range, directly operated thermal overload

relay in sheet steel enclosure for 3phase 415V.50 c/s. A.C. motor up to

7.5 H.P.complete erected on P.W. Block with necessary connection.

208 Lowering of submersible motor pump set at the depth of following 1.00 Nos. 856.48

,complete with required. Nos. and size of casing pipes erected by

means of proper chain pulley block & pipe wrenches after checking of

threads of each pipe with coupling to take the load of the pump set

and pipe assembly filled up with water (D)For Open well Horizontal

submersible pump set for sump well (i) 1 HP to 5 HP

209 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat 10.00 Mtr. 104.03

flexible Submersible copper cable approved make of following Size.(B)

3 Core x 2.5 Sq. mm.

210 Supplying, & erecting C.I. swing, check type non-return (Reflux) Valve - 1.00 Nos. 1020.10

ISI marked suitable for following size.(A) 50 mm dia.

211 Supplying of following size of HEAVY UPVC column pipe with coupler 10.00 Mtr. 359.56

and wire lock.[B] 50 mm dia

Rupees Three Crore Ten Lakh(s) Thirty Thousand Four Hundred Forty Seven And Paise Forty Only

put to Tender Rs. 31030447.40 put to Tender Rs.

Deduction …………….. % below………………… Add ………… % above Rs. …………….

1 The Contractor shall be exhibit board as per government circular No.BDG/3277/1657 N dated 26/01/1997 S (M.GUJ) with

detailed specification and details of work and amount Involved at site without any payment as directed by Engineer-In-

2 All work shall be carried out as per public work department hand book and other specifications of Division or as directed.

3 All columns in the Schedule should be filled in ink & the total of the entries in the last column should be struck by

Contractor under his sign.

4 Rates quoted include clearance of site (Prior commencement of work and its close) in all respects and hold good for work

under all condition, site, moisture/ weather etc.

5 The Boards stating the detailed specification & detailes of Work shal be provided by the contractor as per Government

Resolution T.No.1890-240- Dtd.18/11/1990 and directed by contractor at his own cost immediately on recommanding the

6 Testing of Material Shall be done as per the statement attached with specification,The material IS Tested in GERI by

Executive Engineer Surat and Bill for the testing charges shall be paid by Executive Engineer,1% of the Amount put to

7 1% of the Construction Cost Shall be deducted from the bill Amount of the contract as per the Buildig and other

Construction works walfare cess at 1996(Labour and Employment Department Letter No CWA-2004-1831-M(3)Dated

9/12/2005 notification Of Labour & Employment department dt.03/01/2005 & Labou & Employment Department Letter

8 In Case of RCC items Where there is a change in Grade of Mix or Change as per Actual Mix design the cost of difference of

Cement Difference shall be deducted from the rate of original item at the rate of star rate mentioned in the tender.

9 Contractor are advised to visit site before loading tender rate.

10 Necessary wiring point and drainage point are installed at Site however any modification in electrical installation and

11 The Rates are inclusive of all the taxes (Excluding GST),Transport Charges,Octroi duty and storage Charges up to date.

12 The materials Covered for wiring should be got approved from the Engineer Incharge of the work.

13 GST and Income tax TDS will be deducted at a source while making payments of bills.

14 GST will be paid extra as per Govt. amendment.

15 The Materials on the work shall have to be used and carried out as specified in technical note.

I/We hereby Declare that I/we have Visited the site and fully Exquisite myself/ourselves with the local situation regarding

materials,Labour and other factors pertaininfg to work before submitting tender.

I/We hereby Declare that I/we have carefully Studied the condition of Contracts,Detailed Specification and other tender

Document of this work and agree to execute the same accordingly.

Signature of Bidder Deputy Executive Engineer

Dist ( R & B ) Sub-Division

Executive Engineer Executive Engineer

Vadodara Elect.(R&B) Divison Chhotaudepur ( R & B ) Division

Vadodara Chhotaudepur