RequiredExperience with Government
RequiredOEM Authorization Certificate
RequiredOEM Annual Turnover Bid to RA enabled No Track Suits - Sports ( 635 pieces ) ( Under PAC ) Make benetton Model unitedcolourofbenettontracksuit Technical Specifications * As per GeM Category Specification Specification Specification Name Values Bid Requirement (Allowed Values) UTILITY UTILITY Unisex * COMPONENTS Components Complete Set consisting of Upper and Lower * 1/8 MATERIAL Fabric ( Composition ) Polyester Polyester Percentage of Blending ( in case of Blended Fabric ) Not Applicable Not Applicable Mass ( gram per square mtrs ) 80 80.0 Fabric Construction Knitted Knitted Weave ( In case of Woven Fabric ) Not Applicable Not Applicable Any other weave as per buyer's requirements ( in case weave is other than already mentioned above ) ANY APPLICABLE * Knitting ( In case of knitted Fabric ) Not Applicable Not Applicable Ends per dm Any applicable * Picks per dm Any applicable * Courses per dm Any applicable * Wales per dm Any applicable * Count of knitting yarn Any applicable * Raising at inner side of Main Fabric No No Upper Lining No No Lower Lining No No Lining Material 100% Polyester Mesh 100% Polyester Mesh Mass of Lining (Gram per Square Meter) 55 * Netting mesh No of holes on base & bias within 625 Square millimeter 155 * Technical Requirements of Slide Fastener for Upper Closing Medium special duty Open End as per IS 14181 Latest Medium special duty Open End as per IS 14181 Latest Technical Requirements of Slide Fastener for Pocket Closing ( For Pockets with Slide Fastner for closing ) Medium special duty Open End as per IS 14181 Latest Medium special duty Open End as per IS 14181 Latest Slide Fastners are BIS Marked Yes Yes Width of Tape Elastic at 3.5 cm * 2/8 Waist of Trouser Width of Tape Elastic at Bottom of Upper 3.5 cm * Technical Requirements of Waist Band Waist band as per IS 9686- 1980 latest Waist band as per IS 9686- 1980 latest Waist Draw Cord Polypropylene Cord of 4mm dia * Draw Cord Ends Fused * Breaking Strength of Draw Cord 340 N minimum * Sleeve Ends ( Cuff ) Elastic Tape * Upper provided with Piping No No Lower provided with Piping No No Piping Fabric- Composition 100 percent Polyester * Piping Fabric- Any other material as per buyer's requirements ( Other than mentioned above ) Any applicable * Piping Fabric Mass ( gram per square mtrs ) Not Applicable Not Applicable Embroidery Thread Polyester Polyester SIZE Size Large (L) Large (L) DIMENSIONS OF UPPER Width Across Chest 25 mm below under arm 55.0 cm ( Large ) * Width Across Bottom Opening (relaxed) 48 cm ( Large ) * Length at front from top of collar to bottom 68 cm ( Large ) * Sleeve length (from center of back to bottom of sleeve 87 cm ( Large ) * Sleeve opening relaxed ( Cuff ) Width 10 * Front Neck Drop 10 * Back Neck Drop 2 * Length of Slide Fastener 66 cm( Large ) * DIMENSIONS OF LOWER Side Seam Length 107 cm ( Large ) * Waist relaxed ( Width 45.5 cm ( Large ) * 3/8 Across ) Waist stretched (Width Across ) 55 cm ( Large ) * Seat/Hip ( 15 cm below waist band) 55 cm ( Large ) * Thigh (at Crotch) ( Width Across ) 37 cm ( Large ) * Bottom Opening ( Width Across ) 24 * Front rise including waist band 29 cm ( Large ) * Back rise including waist band 39 cm ( Large ) * Length of Waist Tying Cord 160 * Bottom Fold (Hem) with full turn in(cm) 1.5 * POCKETS Number of Pockets (Upper) 2 Side Pockets 2 Side Pockets Size of Side Pockets- Upper ( Length X Width ) ( cm ) 17 cm X 18 cm * Size of Inside Pocket at Chest- Upper Not Applicable * Side Pocket opening - Upper 15.0 cm * Side Pocket Closure with Slide Fastener -Upper Yes Yes Number of Pockets (Lower) 2 Side Pockets 2 Side Pockets Size of Side Pockets - Lower ( Length X Width ) ( cm ) 17 cm X 18 cm * Side Pocket Opening- Lower 17.5 * Pocket Closure with Slide Fastener - Lower All Pockets with Slide Fastener All Pockets with Slide Fastener Material of Pockets Main Basic Fabric * COLLAR Collar Type Stand and Fall Type
RequiredMade of two layers of self material * Collar Reinforcement With Canvas Reinforcement * SLEEVE Sleeve Type Reglan Sleeve * 4/8 PIPING Position and Dimensions of Piping on Upper NA * Position and Dimensions of Piping on Lower NA * STITCHING Sewing Thread 125 d tex X 3
RequiredPolyester * Raw edges
Requiredif any shall be bound by overlock stitching Yes * Waist band stitching of Upper Stitched in single rows with chain stitch on the elastic * Sleeve Bottom (Cuff ) Stitching Stitched in single rows with chain stitch on the elastic * Waist band stitching of Lower Stitched in single rows with chain stitch on the elastic * Lining seams Not Applicable * Bartack Stitching ( Reinforcement Stitching ) at stress bearing areas No * Tunnel at Waist Band for Lower Two holes stitched to allow the draw cord with insertion free movement * Stitches per dm ( min ) 36 * COLOUR/PRINT Colour Multicolour Contrasting Pannels Any other colour as per buyer's requirements * Multicolour Contrasting Pannels Any other colour as per buyer's requirements APLICABLE * Sublimation Printing (for 100 % polyester only) Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements Sublimation Print as per buyer's requirements APLICABLE * Colourfastness to Light ( IS 2454 ) 5 * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3)) Change in Colour- 4; Staining of Adjacent Fabric- 3-4 * 5/8 Colourfastness to Rubbing ( IS 766 ) Dry- 4/Wet- 3 * Colourfastness to perspiration ( IS 971 ) 4 * Colour of Mesh Lining Any other colour as per buyer's requirements Any other colour as per buyer's requirements Any other colour of Mesh Lining as per buyer's requirements APLICABLE * Colourfastness to Washing ( IS/ISO 105-C10
RequiredTest- C (3))- Mesh Lining Not Applicable * Colourfastness to perspiration ( IS 971 )- Mesh Lining Not Applicable * Colour of Piping Material Any other colour as per buyer's requirements * Any other colour as per buyer's requirements Applicable * OTHER REQUIREMENTS Pilling Resistant [after 5 hours Test as per IS 10971 (Part 1)]
Requiredmin 4 * Dimensional stability to washing
RequiredShrinkage or Elongation Percentage
Requiredmax ( IS 2977 latest)
Requiredin lengthwise and widthwise direction 1 1 LOGO AND MARKING Logo/Totem Marking As per buyer's requirements As per buyer's requirements Type of Logo Printed Printed Number of Logos on Upper 1 1 Number of Logos on Lower 1 1 Size
RequiredDesign and Location of Logo as per buyer's requirement Applicable * TEST REPORT Availability of Test Report from designated AHSP NABL/ILAC accredited or Central Government Lab to prove conformity of products to the No Yes
RequiredNo 6/8 specification Test Report No NA * Test Report Date NA * Name of the Lab NA * Address of the Lab NA * Test reports to be furnished to buyer on demand
Requiredif claimed to be available Not applicable * ADVANCE SAMPLE Agree to provide Advance Sample(s) for buyer's approval before commencement of supply Yes Yes * Specifications highlighted in bold are the Golden Parameters. * Bidders may note that In respect of non-golden Parameters
Requiredthe specifications 'Values' chosen by Buyer will generally be preferred over 'Bid requirement ( allowed Values) by the Buyer. Additional Specification Documents
