PROVISION OF EXTERNAL WATER PIPLINE FROM EXISTING BOREWELL TO UG SUMP , SPORTS FACILITIES, GALVALUME SHEET FENCING ABOVE BOUNDARY WALL CG LAND, SPL REPAIR FOR REPLACEMENT OF AREA LIGHTS AND CONNECTED WORKS AT ICGAE PBR UNDER GE I CG PORBANDAR

Amount

SCHEDULE 'A'

Surface dressing n.exc 15 cm deep and getting out in hard/dense soil complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/disintegrated rock complete all as specified

Excavation in trenches not exc. 1.5 m wide and not exc 1.5 m in depth and getting out in any type of soil, complete all as specified and directed.

Excavation in post holes (or similar holes) in soft/disintegrated rock each n.exc 0.5 cu.m ,getting out, returning, filling in and ramming each or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 mtr and making good surface complete all as specified and directed.

M&L Plain cement concrete, type D2, (1:4:8, using 40mm graded stone aggregates) as in foundation, filling and mass concrete etc all as specified and as as directed by engineer-in-charge. Note: The proportioning of cement and aggregate for mixing by weight shall be as directed by the Engineer-in-charge.

M&L Porbandar stone masonary, block in course, well bonded and bedded, built in CM 1:6 all as specified and as directed by engineer-in-charge.

M&L PCC,, 1:2:4, type B0(using 12.5 mm graded stone aggregates) as in coping, bed blocks for hold fasts and similar works complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified

Removing excavated soils to a distance exc 500m but n exc 1.5 km and depositing where directed.

Removing excavated material not exc. 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified.

M&L Hardcore of guage n.exc. 63mm, deposited spread & levelled in layers n.exc.15CM thick, watered & rolled/ rammed to a true surface using broken stone or boulders all as specified and as directed by engineer-in-charge.

M&L 75mm thick, Plain Cement concrete, type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base of floors even and rough finished to receive topping layer complete all as specified and as directed by Engr-in-Charge.

M & L for 15mm thick Rendering on brick ,concrete surfaces in cement mortar (1:4) on fair faces of stone masonry walls or finished even and smooth without using extra cement etc complete all as specified & directed.

M&L Preparing of newly plastered surfaces and applying two coats of cement base paint (of approved tint) over a coat of primer complete all as specified

M&L for laying of Multi-sport Turf (curly) 15 mm thickness,levelling, compecting complete all as specified and directed.

M&L for 50mm wide line marking for Volley ball/Kabaddi court complete all as specified and directed.

S&F Mild steel work as in posts/struts in fencing including cutting, tops to shape as directed, drilling holes notching for wire etc, complete conforming toFe-290 Grade E-165 complete all as specified.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screw ,complete all as specified and directed.

S&F Plates (plain or chequered) channels,square cut or notched (ordinary and counter sunk) forming holes,without any attachment conforming to Fe-290 (Grade E-165 ) complete all as specified

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end andscrewed the other, or screwed both end to be fitted with washer and one one hexagonal or square nut,length of bolt exc 22.5 cm and n.exc 30 cm long, complete all as specified and directed.

M&L preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of epoxy paint over a coat of red oxide primer complete all as specified and as directed.

Supply and laying in trenches centrifugally cast (spun) ductile iron pipes of 100mm dia suitable for pressurized water delivery with spigot & socket end, class `K-9' confirming to IS : 8329/2000 (latest version) - blast furnace slag cement with portland cement properties suitable for (push on) rubber gasket jointing with inside cement mortar lining and black bitumen external coating, duly ISI marked in any length including testing and commissioning all as specified and directed. Make: Jindal / Electro steel / Electro therm

Supply and fix in replacement of 100mm bore cast iron sluice valve with flanged ends of type PN-1.6 confirming to IS : 14846:2000 with cast iron wheel and brass spindle complete all as specified and directed.

M&L for construction of valve chambers size 1050 mm x 750 mm x 1000 mm depth, incl earth work, with PCC foundation in the ratio 1:4:8 stone work in cement mortar in the ratio 1:4, plastering 15 mm thick in the ratio of 1:4 incl MS sheet cover 3mm thick with angle iron frame 25 x 25 x 4 mm size, locking arrangement complete with painting on steel surfaces with two coats of synthetic enamel paint over a coat of red oxide and all as specified and as directed by EIC.

Material and labour for ISI marked ductile iron socketed fittings supplied as per IS:9523/2000 of class K-12, PN-10 for pressurized water delivery with inside Cement Mortar lining and outside zinc followed by black bitumen coating for size 100 mm dia to 250mm dia such as bends, Tapers tale pieces, Tee pieces (single branch) Y junction doubled branch, cross collars, caps and plug set including rubber ring push on joints complete as specified and directed.

Supply, installation/Lowering Submersible pumpset, discharge 240 LPM and head 50 m,Electric driven, 415 V, stainless steel body, water filled,fitted with Non return Valve to prevent backflow,with submersible cable of rating as per manufacturer (from panel to submersible motor, length of cable as per site requirement) all as spd and directed by Engineer-in-Charge. Make: Crompton Greaves/ KSB/ Kirloskar brothers/ texmo

Supply and fix Cast Iron Air Valves , conforming to IS 14845 of size 50 mm dia bore and fixing up in Cast Iron Water supply mains all as specified and as directed.

Supply and fix Non return valve PN 1.6 confirming to IS 5312 Part -I & II of size 100 bore complete all as specified and as directed.

Supply and fixing 4Mtr hight decorative pole of Cast Iron-Cast Aluminium(CICA) MS Pole embellishments. Ornamental EDGAR with designer bracket is made of round tube conforming to IS 1161 with The pole with bracket is given pre-treatment and finished with Polyurethane Paint(PU) giving it a pleasing appearance and antique finish. The pole is provided with 4 nos. of hot dip galvanized type anchor bolts. A door is provided with anchorage and wiring accessories in the base section.The pole shall be provided polyurethane paint.The pole will be supplied Decorative Double arm and luminaire combinations . Make BAJAJ/UTKARSH/SURYA

Supply and fixing of GLORIOSA Decorative street light fitting, made of - Aluminium Housing .Heat Management with High Pressure Die Cast Al. Diffuser Optical grade Opal PMMA with IP 65 protection for optical compartment with System Efficiency > 85% ,Surge Protection : 4kVA, Ambient Temprature : -10C to +40C, System wattage : 36W LED system having CCT complete all as specified and as directed

Supply, laying, Jointing and testing 16 Sq mm 4 core XLPE insulated, Extruded PVC outer sheath and inner sheath, galvanised steel armoured cable with aluminium conductor suitable for rated voltage of 1100 Volts grade and laid in trenches/pipe / ducts or on pole complete all as specified and directed Make: Havells/RR Cables/Polycab

Supply and lay 50 mm outer dia double wall corrugated (DWC) high density polythene pipes having corrugation on the outer wall and plain surface on the inner wall confirming to IS 16205 & IS14930 ( Part I and II) for protection of underground cables with all fittings. laid in trenches / road/ nallah or fixed along wall. poles or laid under floor (including cutting floor/Road and making good to match with existing adjoining surface etc for cable protection all as specified (excavation and earth work shall be measured and paid separately) Make: Rex/Poly/Geminii

S&F LED Bollard light Cool white 6500 K of wattage 11 watt with integrated mounting base plate and driver complete with housing dark grey RAL 7043 with long life time of 50,000 hours (70% lumen maintenance @ Tc = 35ºC), IP65 protection and IK10 impact resistance including PCC (1:2:4) foundation of suitable size for mounting of light fitting including mounting pole with accessories not less than 1.2m height complete all as specified and directed. Make Wipro cat Ref No LB14-131-XXX-65-05 or equivalent to Philips. Note: The Contractor should submit LM 79 & LM 80 certificates for the batch of fittings procured before incorporating fittings in the work.

M&L Earthing complete with excavation and earth work in any type of soil with galvanized steel earth plate electrode size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs below ground level) with top edge of the earth plate not less than 1.5 mtr below normal ground level connected to GI earth strip 32 x 6 mm by means of bolts nuts check nuts and washers of galvanized iron, all as shown in electrical plate No.3 of MES SSR Part-1 connected to main switch board or main control board all as specified and testing on completion including provision of earth strip protected by galvanised iron 40 mm dia bore light grade pipe and watering pipe shall be 20 mm bore medium grade, PCC pit with pre cast RCC cover, charcoal / salt funnel etc. complete all as directed. NOTE : (1) The conctrete pit shall be PCC 1:3:6 tye C -1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 8 mm TMT bars with suitable cast iron handle shall be provided (ii) Item includes the cost of 7.5 m GI pipe for protection of earth strip (iii) Item includes the cost of 7.5 mtr length earth strip 32 x 6 mm (iv) Result of earthing is not less than 2 Ohm

badri glass and construction

Bharat Enterprise

roxy enterprise

jitendra c joisar

fakhrie apostrical

KRISHNA ENGINEERING

JAMNAGAR ELECTRIC AND MACHINERY CO