Construction of Drug De-Addiction Centre at GMC Baramulla.

Demolishing R.C.C. work manually/by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge.

Earth work in excavation in all kinds of soil by Manual/mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed by site Engineer incld.cutting of trees, removal of tree stumps and dewatering of trenches during execution of work..

Boring, providing and installing bored cast-in-situ reinforced cement concrete pile of specified grade concrete mix, diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embeded in the pile cap etc. all complete including removal of excavated earth with all lifts and leads(Length of pile for payment Shall be measured from top of shoe to the bottom of pile cap) 600 mm dia piles in M30 Grade By percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete,

Breaking of existing heads of Piles to remove the bad concrete exposing of steel for laying of pilecap using mechanical breaker or manually, finished work to be measured. Complete Job.

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor pile method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer-in Charge. Single pile upto 50 tonne safe capacity. Initial test 1 no (Test Load 2.5 times the safe capacity)

Routine test 1 no (Test Load 1.5 times the safe capacity)

Supply and filling of dry stone soling in foundation trenches/under floors tightly hand packed with hand ramming, dressing ,watering incld. carriage of material from source to site of work complete

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) mix complete job

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. M25 Concrete.

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) complete job

Reinforcment for R.C.C. work incl. straightening, cutting, bending, placing in position & binding all complete.Thermo Mechnically treated Bars.

Providing and filling of GSB in underfloors of Rooms inluding hand ramming complete job.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20mm nominal size stone aggregate.

Centering and shuttering including strutting propping etc. and removal of form for foundation, footings basses of columns etc . For mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platforms

Centering and shuttering including strutting, propping etc. and removal of form for stairs (excluding landings) except spiral staircases

Centering and shuttering including strutting, propping etc. and removal of form for Columns, piers, abutments, pillars, posts and struts

Dry random rubble masonry with hard stone in foundation & plinth using Quarry stone with bond stone.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Tile brick masonry work 5cm thick with common burnt clay non modular tile bricks of class designation 10 in cement mortar 1:3 (1 cement : 3 coarse sand) and curing complete in superstructure above plinth level upto floor five level.

P/F of wood work in frames of doors & windows, clestory windows & other frames, wrought framed & fixed in position with hold fast lugs or with dash fasteners of required dia & length of KD Imported wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. 30 mm shutters KD imported wood complete job

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws KD imported wood 30 mm shutters complete job

Providing and fixing 30 mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both direction with wire of dia. 0.63mm for doors, windows and clerestory windows with hinges and necessary screws : lSI marked M.S. pressed bright finished butthinges with necessary screws of required size. Ist Class Kail Wood.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete. : 200x10mm

Providing and fixing bright finished brass handles with screws etc. complete : 125mm

Providing and fixing bright finished brass. sliding door bolts with nuts and screws etc. complete :

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 200x10mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125mm

Providing and fixing of M.S rod locks with inbuilt sliding bolt, screws ,nuts of heavy duty complete of approved quality (Godrej, Link or equivalent make

Providing and fixing aluminum Cat Eye hooks/Wind Hooks ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 100mm

15mm Cement plaster on the rough side of single or half brick wall of mix: complete job

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand): complete job

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete 2 mm thick complete job

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound) content less than 50 grams/ liter of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two coats

Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. of size 300mmx450 mm digital type

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm

Providing & laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen & the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. Per sqm of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (18mm Granite of any colour or Shade)

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests including all carriages

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid , 10 liter low level white vitreous china flushing cistern and CP flush bend with fittings and C.I. brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing of Plumbing Fixtures of quality make ISI Marked like Jaquar, Essel, Hindware, cera etc Bibcock C. P Brass

C.P Brass basin Mixer

Wall mixer

Sink Mixer

Stainless steel sink

C.P Brass Angle Value

C.P Brass Grating 100mm dia

C.P Brass Health faucet chain type 1.5 mtr

2in1Angle value

C.P Brass Towel Rail 600mm x7.8mm

C.P Brass Soap case

Toilet paper Holder

Spray Fusset

Glass Shelf

Fency Type Glass

15mm dia PPR Pipes including fittings

20mm dia PPR Pipes including fittings

25mm dia G.I Pipes including fittings

32mm dia G.I Pipes including fittings

Union 20mm

Union 25mm G.I

Union 32mm G.I

6" PVC pipes to leach pit

4" PVC pipes to Drain sullage

3" PVC pipes to Drain sullage

Collar different dia

Bend different dia

PVC Tee different dia

PVC Reducer different dia

Floor Trap

Vitrous wash basin with padestal

Gate valve 25mm

Ball valve 15mm

Providing and fixing of water heating geysers of approved brand & quality (Venus/ Jaguar/ Racold or Heavells eqviuallent) with all necessary fittings and fixtures complete Job. 50 Ltr capacity including all costs and cariages complete

Construction of Man holes / inspection chambers (600 x 600 x 600)mm in brick masonary 1:6 mix including earthwork in excavation, P/L of stone solling, Base concrete 1:4:8 mix internal plaster 1:3 mix, cc flooring in 1:2:4 mix, top slab in 1:2:4 mix with M.S Manhole cover & frame all complete as directed by Engineer in charge.

Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete, including all carriages

Providing & fixing corrugated high Rib type G. S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, nuts bolts in horizontal/ vertical or curved surface)excluding the cost ofpurlins, rafters bolts and nuts 8mm diameter with bitumen and G. I limpet washers including ridges, hips valleys all complete. .50 mm thick complete job

Carraige of materials by mechanical transport from source to site of work incl loading and unloading complete Stone aggregates upto 40-20mm for an average lead of 10 km

Sand for an average lead of 10 km

Bricks from Budgam for an average lead of 60 Km

Stones From Quarry for an Average lead 5 km

Carriage of un-serviceable materials average lead 10Kms 70% only

ELECTRIFICATION. Wiring for Light point/Fan point/Exhaust fan/Bell point with (P+N+E) 3x1.5 sq.mm FRLS-H PVC insulated Multi strand Copper conductor single core cable, (Havells/Anchor/Eq Make) in surface/recessed Conduits laid in slabs (Including Cost of Conduit 25mm) with 01 No.of 6 Amp Modular Switch, Modular Plate, Cover in front & suitable GI box etc ISO/IEC Certified/Schneider/Havells/Legrand/Anchor roma plus/ABB/Eq.Make & along with 2.5 Sqmm (P+N+E) Circuit Wire of same make as mentinoned above & items shall be approved before execution of work by SDO.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required, ISO/IEC Certified of Havells/Legrand/Anchor/Schneider/ABB/Eq Make & shall be approved before execution of work by SDO.

Wiring for Power Plug with (P+N+E) 3 x 4 sq.mm FRLS-H PVC Insulated Multi strand Copper Conductor single core cable in surface/Recessed Conduit (Havells/Anchor/Eq Make)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required, ISO/IEC Certified/Legran/Anchor roma plus/Schneider/ABB/Eq Make & shall be approved before execution of work by SDO.

Wiring for 6Amp Plug (Computer Point) with (P+N+E) 3 x 2.5 sq.mm FRLS-H PVC Insulated Multi strand Copper Conductor single core cable in surface/Recessed Conduit (Havells/Anchor/Eq. Make)

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including proving and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings), ISO/IEC Certified Havells/Legrand/Anchor roma plus/Schneider/ABB/Eq.Make & shall be approved before execution of work.

Wiring for Sub main Wiring along with earth Wire with the following Sizes of FRLS-H PVC insulated copper conductor, single core Cable in surface/Recessed medium class PVC conduit (Havells/Anchor/ Eq.Make) & shall be approved before execution of work (Including Cost of Conduit/Channel) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supply/Fixing Testing and Commissioning of 6Amp to 32Amp Rating SP,240v,C Curve 10K, Miniature Circuit Breaker suitable for inductive load of following poles in existing MCB. DB Complete with connections.(L&T/Siemens/Legrand/Havells/ABB/Eq. Make)

Supply/Fixing/Testing and Commissioning of following rating, Double pole, (P+N) 240 V, C* Curve 10K, Miniature Circuit Breaker (MCB) in the existing MCB DB complete with connections. (L&T/Siemens /Legrand/Havells/ABB/Eq Make) 63Amp

Supplying and Fixing of MCB way 8 way (4+2), horizontal typed, sheet steel, Double Door Distribution Board, TPN 240V/415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, Interconnections, powder painted including earthing etc, as required. (L&T/Siemens/Legrand/Schneider/ABB/Eq Make)

Spplying and Fixing of MCB way 4 way (4+24), Horizontal typed, sheet steel, Double Door Distribution Board, TPN 240V/415 V, on surface/ recess, complete with 8 tinned copper bus bar, neutral bus bar, carth bar, din bar, interconnections, powder painted including earthing etc, as required. (L&T/Siemens/Legrand/Schneider/ABB/Eq Make)

Supply/Installation/Testing and Commissioning of 18W + LED Conceal/Surface (Commerical Type) light luminary fitting round shape with minimum system lumen efficacy of 100 lm/W with Pressure Die cast Aluminium Heat Sink and P.F.>0.95,THD<10%, CCT 5700K, CRI 80.The LED with Useful life of 50000 Hrs at L70.. The Input voltage range shall be 150V to 270V. The Fixture should have In-built Surge Protection of 2kV.Certification:- LM79 & LM80 test report should be from govt approved In-house NABL lab/government of India authorised lab. The job includes AMC (reckoned from date of successful commissioning) of lighting fixtures for a period of Two years, which includes replacement of fixtures of Philips/Havell's/Wipro/Halonix/Eq Make.

Providing & Fixing of IK08 IP-66 protected high power LED 50 Watt flood ght system with single piece Pressure diecast aluminium housing. toughened glass diffuser with suitable lenses on LED to achieve various beam angles, of high power LED of 3 to 5 watt each. Integrated potted driver as a unique BIS R number having efficiency more than 85% and in compliance to BIS certified and Trade mark certificate. The System level Luminaire efficacy >=125 Im/wt. LED driver Input Voltage AC 120 10 270 V AC with High voltage Cutoff @>>300 V AC and Auto resetting Safety Power Factor >0.95, THD(1) <10%, driver current 750mA, driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector, Surge Protection Min 4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hours with 70% of Initial Lumens maintained, CRI>70 and CCT 5700K 355K. Manufactures 11 Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/work, refer Annexure "A" attached with this BSR:-High Power LED Flood Light Minimum lumen output 6200 Im of Havells/Crompton/Philips Make as approved and to be installed on outsido block including S/F of suitable size of Gyser bolt. The job further includes replacement warranty of fixture (if damaged/burnt out what so ever reason) for a period of two years reckoned from date of successful commissioning /handing over of site to intending department.

Supply, Installation, Testing and Commissioning of decorative 1200 mm sweep, ceiling fan with 3 No, Aluminium blades, 30 cm long down rod, 2nos. canopies, shackle kit, Power Factor not less than 0.9, Service Value including safety pin, nut bolts, washers, temperature rise 75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, and including iron hook complete. USHA Striker/Havells Oyster matalic/CromptonAura/equivalent make as directed by engineer incharge.

Supply/Installation/Testing and Commissioning of 225-250mm Shutter Typed, 320 Cu.m/Hr.AC 220-240 Volts, 50 Hz Exhaust fan made out of ABS Plastic Material with inbuilt thermo cut-off Protection and Noise Level not exceeding 37dB of Following Sizes including connection etc USHA/Havells/Crompton/Eq. Make.(Min 1-Star)

Supply/Laying/Connecting and Commissioning of 70 sq.mm 3.5-Core XLPE/PVC insulated and steel armored 1.1 KV grade Aluminum Cable of Havells/Polycab/Eq. Make with required size of thimbles dully crimped with hydraulic crimping tool including Providing/Fixing of saddles/clips with making of connection and partially to be laid underground through DWC High Density Poly ethylene Pipe having Corrugation on Outer wall and Plain surface inner wall Conforming to IS: 14930 Part-1 and 2 Complete with accessories for Protection of 1.1 KV Grade under Ground cable Directly in Ground at a Depth of 50 CM including excavation and Refilling the Trench (Material to be approved before execution)

ENVIRONMENTALLY SAFE MAINTENANCE FREE COPPER Rod EARTHING SYSTEM Necessary soil treatment is to be made by the contractor in order to improve the Pit resistance Value Supplying, Installation and Testing of 75 mm copper Pipe Filled with Crystallineconductive Mixture with Eco friendly GEM Backfill Compound 2No. Bags also having Earth pit chamber (300mm x 300mm) with man- hole cover for the above. Including cost of 20MM Wide copper strip as required in one run fitted with of brass nut bolt & spring washer from EARTHING ROD up to MAIN Control PANEL through DWC High Density Poly ethylene Pipe having Corrugation complete job

Supply Installation Testing & Commissioning of 3 Star rating 1.5 TON inverter type split Air Conditioning system suitable for operation on AC supply single phase 220 V The indoor unit fitted on wall by employing suntable clamps and the outdoor unit fitted on the wall by using suitable angle iron stand fitted with nuts/bolts outside the room to avoid noise, including standard length of suitable size copper tubing covered with nitrilic foam, topping up with refrigerant for additional length of piping if required, PVC flexible drain pipe, suitable capacity 3 core sheathed/pvc insulated coper cable and a battery operated wireless remote unit, the job also includes repairs to walls wherever the same are cut and the AMC of AC for a period of one and a half year from date of successful commissioning, <O-General make) including cost of 5 KVA Digital Auto control VOLTAGE Stabilizer for ACs of Approved brand for smooth functioning/ constant voltage supply having etc Input voltage 90-220 volts & output voltage-220 volt & stand Copper piping ete & all other allied accessories, installation charges. GST, income tax, Carnage ete Complete job The job includes CMC (reckoned from date of successful commissioning) for a period of Two years.

Supply & fixing of Modular AC box with 32 AMP Single pole MCB of Havells/Legrand/Schneider/L&T make

Supply, installation testing, &commissioning of 50 KVA 3-Phase ERVO controlled VOLTAGE Stabilizer of Approved brand with following SPECIFICATIONS: (1). INPUT VOLTAGE: 156 Volt-450 Volts P-P (90V-260V N-P) (2) OUT PUT VOLTAGE: 400Volts+ 1%(230VAC) (3) Winding Material Insulation: 99.97% PURE COPPER WOUND FIBER GLASS (4). IN DOOR TYPE (5). COOLING:OIL IS 335 (6).MICRO CONTROLLED TRUE RMS Based LCD display (7). Protections are Over Load COPPER wound of Electric Field/Alba/AE/Cosco/Eq.make etc ISI/ISO certified for smooth functioning/constant voltage supply having Technical Specifications: Input voltage-90-260 volts & output voltage 220 volts+-2% Buck Boost Transformer Copper wound 99.9%,OIL Immersed COOLING OIL, High cut/Low Cut/Time delay/Over Cut through Micro Control and Spike Protection including, Carriages installation charges, testing & taxes complete job alongwith servo bypass switch of adequate rating.

Supply/Installation/Testing and Commissioning of 125 Amp Four Pole manual bypass changeover switch of Havells / Siemens/ ABB /Schinder/L&T/Eq make

Please Enable Macros to View BoQ information