PROVN OF TOILET BLOCK NEAR P-45 SECURITY GATE WITH LOW SECURITY WALL, SENSOR DOORS AND GARBAGE BIN UNDER GE

Amount

Surface excavation n.exc 30 cm deep & averaging 15 cm deep getting out in Hard/dence soil as specified and directed

Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes, etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

M&L PCC 1:4:8 type D2 (40 mm graded aggregate) in foundation filling and mass concreteetc complete etc.all as specified and as directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work fair finish surfaces complete all as specified and as directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions (Square, rectangular or polygonal) etc. ; fair finish surfaces complete all as specified and as directed.

M&L for providing RCC 1:1-1/2:3 type A1 (using 20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc.; complete all as specified and as directed.

M&L for providing RCC 1:1-1/2:3 type A1 (using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts, etc.; complete all as specified and as directed.

M&L for squared rubble walling jodhpur type, brought upto course,well bonded bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

Extra over for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm and dressing face beds and joints as specified to squared rubble walling,Jodhpur type, brought upto courses all as specified and as directed.

M&L for Pre-cast cement concrete block type C1, 1:3:6 (20mm graded aggregate) as in masonry with solid blocks, exc. 10 cm in width and setting in cement Mortar 1:6 complete all as specified and as directed.

M&L for Form work to sides and soffits of floor or roof RCC beam sides of lintel beam flat fair finish surfaces complete all as specified and as directed.

M&L for Formwork for chullah hoods, chajjas through and similar items including edges, surface fair finished complete all as specified and as directed.

M&L for Reinforcement 10mm dia and over TMT bars cut to length, bent to shape required and binding with MS wire not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for Reinforcement 8 to 10mm dia TMT bars cut to length, bent to shape required and binding with MS wire not less than 0.9mm dia in stirrups complete all as specified and as directed.

M&L Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in lintels upto 1.50 m clear span, cills , steps, seismic and other similar bands, copings, kneelars, apex stones, bed plates, bed blocks of hold fasts etc including necessary form work complete all as specified

M&L Plain Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in copings of parapet walls including necessary form work complete all as specified

S&F mild steel rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, fencing post etc; Confirming to Fe 410 -W (Gde E- 250) complete all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed.

MS framed work as in doors or gates of flat, angle, rolled or other section partly ornamental/ intricate design , incl gusset plates, braces etc; but without coverings incl all necessary welding and / or rivetting etc including pintle or any other type of hinges Fe - 290 ( Gde E - 165 ), complete all as directed.

S&F Mild steel wire fabric any type and size weight not exceeding 4.00kg per square metre fixed with steel members including required welding and other fixing arrangements etc; complete all as specified and directed.

M&L for providing RCC 1:1-1/2:3 type A1 (using 20mm graded stone aggregate) as in beams, lintel up to 1.5m clear span, lintel bands etc; complete all as specified and as directed.

M&L for Jodhpur stone roof slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, hoisted and set, jointed and grouted cement mortar 1:3 complete complete all as specified and as directed.

M&L for carrying out water proofing treatment for roofs in the following stages - (i) Rendering 10mm thick in 1:4 mixed with integral water proofing liquid all as per manufacturer's instructions over concrete surfaces finished even and smooth with out using extra cement. (ii) First coat of bitumen primer confirming to IS 3384 @0.300 Kg/ Sqm over plastered surafces (iii) Second layer of 3.0 mm thick APP modified polymeric membrane with centre core of Single non woven polyster reinforcement and having weight 3.60 Kg/ Sqm with mineral gravel finish on top complete laid with blown type bitumen grade 85/25 @ 1.20 Kg/ Sqm complete all as specified and as directed. (iv) Finally applying two protective coats of bituminous aluminium based reflective paint to safeguard against UV, including preparing of surfaces of roof, remove all corrosion products brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots incl washing , rubbing down and stopping of painted surfaces (second coat apply after 24 hrs or as per manufacturing instructions).

Supply only integral water proofing liquid ISI marked Make: Pidiproof LW

Returning,filling in,including spreading,levelling,watering and well ramming in layers not exc 25 cm each layer in hard/dense soil all as specified and directed.

Removing excavated soil n exc 50 m and depositing where directed at a level n exc 1.5 m above the starting point all as specified and directed.

M&L for Jodhpur stone slab patti 40 to 50mm thick set in over and including 15mm thick cm 1:4 and jointed & pointed in neat cement slurry as in floors, plinth protection, steps etc; complete all as specified and directed.

M&L for keyed pointing in CM (1:3 ) to Jodhpur type regular coursed masonry complete all as specified and as directed.

M&L for 15 mm thick rendering/Plastering on stone masonary wall or other than fair face of brick/ stone work surfaces in CM 1:4 finished fair and even all as specified and as directed.

M&L for rendering 15 mm thick in CM 1:6 finished even without using extra cement over stone wall surfaces all as specified and as directed.

M&L for 10mm thick rendering in CM 1:3 on ceiling surfaces finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparing new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for prepraing new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

Preparing new steel surfaces and M&L for applying two coats of synthetic enamel paint over one coat of red oxide primer.

M&L Preparing newely untreated surfaces of steel and iron work, of any description and girth, not otherwise described, and treated with tar or coal tar black paint etc., complete all as specified and as directed.

Preparing new plastered/ pointed surfaces and material & labour for applying two coats of cement base paint on walls including one base coat of white wash etc., complete all as specified and as directed.

M&L for PCC 1:2:4 type B0 25 mm thick using 12.5mm graded stone aggregates as in sub floors/base floors under tiles as in levelling course etc all as specified and directed.

M&L for PCC 1:2:4 type B-1 40 mm thick using 20 mm mm graded stone aggregates as in sub floors/base floors under tiles as in levelling course etc all as specified and directed.

M&L for PCC 1:2:4 type B1 50 mm thick using 20 mm mm graded stone aggregates as in Plinth protection including Provision of construction joints complete all as specified and directed.

M&L for Non - skid Coloured Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer in CM1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed.

M&L for glazed ceramic coloured tiles of size 300X200X7 mm thick in dado/skirting etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:3 as in backing coat of tiles complete all as specified and as directed.

M&L for 16 -18mm thick granite (black colour) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

S&F Solid PVC door frames factory made of size 50x47 mm made out of 5 mm plain coloured PVC sheet reinforced with MS square tube complete all as specified and as directed from approved manufacturer.

S&F for factory made solid panel PVC door shulter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with neat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the M.S frame welded /sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement suppling & fixing in the frame at site as per specification of drawing complete all as specified and as directed.

M&L for fabrication of aluminium powder coated ventilators fixed type (with/ without louver) fabricated with anodized aluminium rectangular section in frame & with deco grill of approved design & stainless steel wire cloth on the outer side of frame & trade pattern louvers with suitable mechanism for tilting /opening closing etc all as per sample kept in GE office & fixed in position complete all as directed. (Note : Glass pane in louvers & stainless steel wire cloth shall be measured & paid separately)

S&F for figured glass, pin head type ordinary quality, 4mm thick, area of each pane not exceeding 0.5Sqm and glazing with aluminium beading in aluminium frame all as specified and as directed.

S&F butt hinges, medium weight ,stainless steel of 100mm long size and fixed complete all as specified and as directed.

S&F aluminium, anodised, barrel tower bolt of extruded section, 150mm long all as specified and as directed

S&F extruded aluminium alloy handles, 150mm long size, fabricated type, anodised all as specified and as directed.

Supply and laying 15 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and as directed.

Supply and laying 25 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and as directed.

Supply and fix Bib tap,15mm bore, fancy type, brass chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified and as directed.

Supply and fix Angle valve,15mm bore, fancy type, brass chromium plated, concealed type, with long shank and cup, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

S&F for cast copper alloy chromium plated 2 in 1 Angle Cock Complete all as per sample and all as specified and as directed.

Supply and fixing for Pillar tap/ Aria Chrome Single Concealed Stop Cocks with Basin Spout Kit, 15mm dia, brass chromium plated, fancy type screwed down, high pressure, with long shank, screwed shanks and fly nuts, screwed for iron pipes or for wash hand basin all as specified and as directed. (Make: Jaquar Cat No.ARI-CHR-39441K) or equivalent in Kohler/Crabtree

S&F PVC connection, 15mm size, with PTMT nuts, of length 450 mm long including taking down of existing old pipe all as specified and as directed.

S&F Vitreous china squatting pan, Orissa pattern, size 580x440mm white/ coloured with integral foot rests including flus pipe and connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete all as specified.

S&F Vitreous China wash down water closet pan (Pedestal Pattern), white including white plastic seat cover with mild steel CP hinging device, suitable brass CP wash jet with 1.00 to 1.50m long tube (Make of Jet 'Praayag' Cat Part No 5211 or Equivalent) incl making connection to inlet flush pipe, & to 'P' or 'S' drain trap, incl supply of long special 'P' or 'S' trap fixed complete and making good the disturbed portion etc. all as specified and directed.

Supply only PVC flushing cistern, low level,10 litres capacity , valveless, syphonic action type, white, with inlet, ball valve, float, handle, flush pipe of polythlene of low or high density or PVC, 32 mm dia all as specified and as directed

Vitreous china under/over counter wash basin, white colour, oval shape, size 560x470mm including CP waste fittings PVC waste pipe of suitable size/ bore and fixed over marble/granite or RCC plateform including necessery cutting accourding wash basin shape/ size etc; and making good disturbed surfaces to match with the existing complete all as specified. (Make: CERA Cat No. S2030104)/ Kohler /Parryware

S&F for Vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement , suitable PVC waste pipe with brass unions, including making all connections to existing connections,complete all as specified and as directed.

S&F CP towel rail 450mm long fixed with and including CP brass screws and wooden/ plastic cleats complete all as specified.

S&F CP greating doom 100mm dia complete all as specified.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top) in white colour, hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 142 gms.) all as specified and as directed.

M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified.

M&L for 60mm thick factory made pre cast cement concrete rubber moulded laquer finish using chemical and admixure inter locking tiles having compressive strength not less than 350 kg/Sqcm, of shape and colour as approved by GE , laid over and including 25mm thick compacted approved sand cushioned surface, joints filled by fine sand and compacting the top surfaces of paver blocks after laid etc of approved make all as specified and as directed.

M&L for factory made precast cement concrete solid blocks M-30 Grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size (with plain or interlocking joints as directed) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish/ surplus soil etc., complete all as specified and directed by Engineer-in-Charge.

M&L for cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in kerbs or benching etc including necessary form work complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 100mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, laid in trenches or in floor etc; complete all as specified.

S&F 75mm bore cast iron soil, waste and vent pipes (sand cast pipes) in any length with or without ears, fixed to walls etc; complete all as specified.

S&F 100mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 75mm bore pipe cast iron 'P' or 'S' trap, complete all as specified.

S&F 100mm bore pipe cast iron cowls, complete all as specified.

S&F 75mm bore pipe cast iron cowls, complete all as specified.

M&L cast iron up to 150mm bore fittings of Bends (any type, radious and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces, single branch, 'Y' junctions, double branch, cross (all sockets or socket and spigot) collars, caps and plugs etc; complete all as specified.

M&L 100mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

M&L 75mm bore cast iron pipes and fittings joints or connections are filled/ sealed properly by epoxy sealant of ISI mark or M-Seal (Make:- Dr Fixit) apply as per manufacturing instructions, complete all as specified.

S&F for 100mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

S&F for 75mm bore pipes stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall etc; complete all as specified.

M&L for bedding to drain pipes 150mm dia including packing under, and haunching against the sides in PCC 1:3:6 type C2 using 40 mm graded stone aggregate against the side of SWG after they are laid and tested all as specified and as directed.

M&L for 150 mm bore SWG drain pipe, of grade 'A' laid in trenches and jointed in CM 1:1, complete all as specified and directed, including testing etc complete all as specified and as directed.

M & L for PCC (1:3:6) type C2 using 40 mm graded stone aggregate as in surfaces channel and drain of man holes finishing surfaces even and smooth complete all as specified and as directed.

M&L for Jodhpur stone patti slabs, self faced 7.5cm to 10cm thick, 25cm to 35cm wide, laid dry as in manhole coveres, sizes as directed by Engineer incharge complete all as specified and as directed.

Cutting into existing manholes, for insertion of 150mm dia of pipe for connecting new drains making good to pipe and rendering cutting out existing benching for and forming branch channel (1/2 round or 3/4 round section) in cement concrete 1:2:4 type B1, smooth finished and reforming benching all as directed and specified as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but not exc 4.00 sqm each and removing from site or to store as directed by Engineer incharge.

Provn of automatic opening glass doors complete with automatic sliding operator . Easy operator 2.40 Mtr long and comprising of track profile 2.40 mm, single phase 230 volt 50/60 Hz motor with SMPS of capacity 180 wat IP-20 light barriers, microprocessor controller programmer data with funtional programmer switch, (1) Off, (2) Automatic, (3) Permanent open, (4) Partial open, (5) Exit only , (6) Night bank switch , (7) Emergency off, Self learning, automatic reversing , connection for light barriers, setting for basic parmeters, via integrated disply and push button, 24 volt out put for external consumption , read out error store with error code floor guide and clamping rail including motion sensor for automatic opening with opening speed 10 to 50 cm/sec and closing speed 10 to 40 cm/sec , holding open time 0.5 to 30 sec including built in of AC 230 volt 630 VA UPS of 'V' Guard make and fixed with frameless (by parting) glass panels of 12 mm thickness toughened with polis, grinded of 'ridhi sidhi' tuft make in double panels as fixed panels of suitable size mm (02 Nos) and sliding panels 1000 x 2400 mm (02 Nos) in other opening fixed panels both side fixwd by SS 'L' connector fitting with silicon sealant bounding. Make Dorma/Technocrets Security System/Avians/Enox /assa abloycomplete all as directed by Engineer-In -Charge

Supply, laying, testing and commissioning of LT UG cable, XLPE insulated, PVC sheathed, galvanized steel strip armoured electric power cable with stranded aluminium conductor, 1100 volts grade of size 16 sqmm 4.0 core confirming to IS:7098 (Part-I), suitable for earthed system, laid in duct/trench/along pole/wall etc including nuts, bolts, washers, saddles & screws etc and making connection, complete all as directed. Make : Havells / Finolex / KEI / RR Kabel / Polycab Note : 1. The cost of Al thimbles/lugs and cable gland etc is included in quoted rate and no extra payment will be made for it. 2. Excavation, earth work, sand cushioning and brick protection will be measured and paid separately under respective items.

All as per srl item no. 91 here-in-before but with 16 Sqmm 2.0 Core

Supply and fixing of LED Post top Lanten Decorative gate light (MUSHROOM (PRISMATIC)) made up of high grade unbreakable polycarbonate material suitable for retrofit LED Bulb 20 W B22 base, Mounting Pole Dia - 60 mm (max) and all required connection necessary PCC work required for fixing etc., complete all as specified and directed by Engineer-in-Charge. Make : Havells Cat Part NoLHFXAMN1TN6F035 Model : MUSHROOM (PRISMATIC) / Philips / Crompton

S&F of LED street light luminaire of 35 Watt capacity, made of single piece pressure die-cast aluminium housing with high power LED with lens for proper light distribution luminiaries, IP 66, with toughned glass cover and incl control gear etc, with and incl making all electric connection alongwith bracket, clamps, nut bolts etc., complete all as specified and directed by Engineer in charge. Make : Philips / Havells / CG / Wipro

S&F of street light fitting bracket, 1.5 mtr long made out of galvanized iron pipe of 40 mm dia size light grade complete with and incl 02 nos MS clamp made of MS flate iron of 50 x 6 mm size with nut, bolts, washer etc with and incl two coats of aluminum paint over a coat of red oxide primer, complete all as directed.

S&F in security light termination box, weather proof, alongwith connector for 3 phases and MCB SP 6Amps incl aluminium strip bus bar mounted on insulator of size 200 x 250 x 150mm, complete all as specified and directed by Engineer-in-Charge. Make : Sintex /Asian

Supply and erection in vertical position steel tubular swaged pole type 410 SP- 31 (8.5 mtr long ) with Mild Steel base plate of size 30cmx30cmx6 mm thick continuously welded to pole , final taper plug ,bolts ,nuts and screws all as specified including factory painted with two coats of black bituminious paint internally throughout and externally for embedded position and two coats of aluminium paint over a coat of red oxide primer over the ground and making 30cm wide strip (total 4 Nos ) with black and yellow paint including numbering, complete all as specified and directed by Engr-in-Charge.

M&L for PCC (1:3:6) type D2, using stone aggregate 40mm graded, with and incl necessary form work where required, fair finish to the exposed surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for PCC (1:2:4) type D-2, using stone aggregate 20mm graded, with and incl necessary form work where required and fair finish to the exposed surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for PCC (1:4:8) type D-2, using stone aggregate 12.5mm graded, with and incl necessary form work where required and fair finish to the exposed surfaces, complete all as specified and directed by Engr-in-Charge.

M&L for sub main wiring with 2 run of 2.5 Sqmm FR, PVC insulated, unsheathed and stranded copper conductor cable with and incl 1.5 Sqmm (nominal area) FRLS, PVC insulated, unsheathed and stranded copper conductor cable as earth wire connected with thimble from main DB to sub main DB, drawn in to separate concealed medium grade, ISI marked, non metallic PVC conduit 15 mm dia size incl all conduit accessories & fittings / junction boxes / inspection covers etc, with and incl cutting chasing and making good of disturbed surface of wall / floor/ ceiling etc as original by brick work, plastering, white washing, OBD etc as required, complete all as directed. Note : 1. The cost of concealed conduit & accessories is deemed to be included in quoted rates. 2. The two run of 2.5 Sqmm wire and one run of 1.5 Sqmm wire will be measured as one unit. 3. Make of Wire : Havells / Standard / KEI / C&S / RR Kabel

Excavation in trenches in hard / dense soil not exceeding 1.5 meter depth and not exceeding 1.5 meter wide and getting out including trimming of sides, complete all as directed.

Removing excavated material to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point, complete all as specified.

Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick, complete all as specified

Supply and laying Jodhpur stone quarry faced stone slab cover 40 to 50mm thick, 25cm to 30cm wide, 60cm long, laid dry and abutting each other with gap between adjacent slab not exceeding 10mm over under ground cables for protection

M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 10cm after laying of cable in trenches complete all as directed and sand cover to under ground cable complete all as directed.

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.

M&L pipe galvanised iron light grade complete with all fittings laid in road crossing, and on pole, buildings complete all as specified and directed ISI marked of 40mm bore

M & L for Concealed point wiring for One light point controlled by one switch using 1.5 Sqmm (nominal sectional area) multi stranded copper conductor, single core, FRLS PVC insulated & unsheathed cable, 1100 volts grade with PVC conduit with sunken pressed steel terminal boxes in wall but including 3.00 mm thick plastic laminated sheet top cover fixed with brass screw and washer with all accessories including single core multi-stranded copper conductor 1.5 sqmm size cable as earth wire ( Green Colour) and connected to earth dolly drawn in same conduit complete . MAKE Of Cable-Finolex/Polycab/Havells

Ditto as per item no 110 but One Fan point controlled by one switch

Ditto as per item no 110 but One 3 Pin 5 Amps socket outlet on same board

Ditto as per item no 110 but One 3 Pin 5 Amps socket outlet on independent board.

Ditto as per item no 110 but using 2.5 Sqmm PVC insulatd, unsheathed cable for one 3 Pin socket outlet 15 Amps on independent board.

M&L for Sub main wiring with PVC insulated but unsheathed 2x4 sqmm multi stranded copper conductor cable passing through and in and incl PVC conduit concealing in wall (by means of chasing incl making good existing ) ISI marked and conduit accessries fixed on surface of wall, ceiling etc, making good the disturbed surface with and incl 1x4 sqmm single core copper conductor cable PVC insulated and unsheathed as earth wire. Note:- Two run of 4 Sq.mm. and one run of 4 Sq.mm. cable incuding one run of PVC conduit will be measured as one length

Supply and fixing switch piano, flush type ,single pole one way 5/6 Amps 240 Volts complete all as specified and directed.

S/F switch socket combination 2 in 1, 3 Pin, and 5 Amp flush type universal complete all as specified and directed.

S&F switch socket combination 2 in 1,5 Pin 5 and 15/16 Amp flush shuttered type ISI mark complete all as specified and directed. Make: Cona/Anchor

S&F ceiling rose surface bakelite three terminal 65 x 50 mm three terminal 250/230 volts ISI marked complete all as specified and directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single MCB SP 32 Amps. Make : Legrand/ABB/L&T

S & F for exhaust fan, metal body, heavy duty 300 mm size with louvers and 3 core PVC insulated copper flexible cable size 23/.0076 including cutting chases on brick wall and groundting with nut bolts on aluminum frame complete all as specified and as directed by Engineer-in-Charge. Make : BAJAJ/ HAVELL'S /CG/ KHAITAN

S&F of LED light fitting 1 X 20/22 watt (4 feet), decorative ultra slim type, with inegral driver, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed. Make : Havells / Wipro / Philips/CG

S&F of LED light fitting 1 X 10 watt (2 feet), decorative ultra slim type, with inegral driver, complete with all accessories and making necessary electric connection from ceiling rose to fitting terminal, complete all as specified and directed. Make : Havells / CG / Wipro / Philips

Supply, fixing, connecting & testing sheet metal enclosures double door, single pole and neutral, 08 way DBs for using MCBs / MCB isolators with having aluminium bus bars suitable for 200 Amps rating with IP-42 protection complete including taking down existing all as specified and directed.. Note : Rates are deemed to be included for flushing in wall concealed complete making good and matching existing surface.

S&F MCB SPN 6-32 Amps,240 Volts `C` Curve complete all as specified and directed.

Supply and fixing MCB SP 6-30 Amp 240 volts complete all as specified and directed. Make:- Legrand /C&S /L&T /INDOASIAN

M/S gayatri construction company

M/s R K Enterprises

JANGID BUILDERS

HINDUSTAN TRADING COMPANY

M/S MAJISA CONSTRUCTIONS

AB Constructions