Installation of Happiness Park Open Gym Fitness Centre at 10 Various locations in valanchery municipality, Malapppuram Dist . Project No. 97/26.

Amount

Civil Work

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD165191/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170793/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of purepolyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170796/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174958/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron

OD174959/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180555/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

MOORKAMBATT

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD165233/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170819/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170820/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174961/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174962/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180556/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe handle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron

PANIKKARPADI

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD165239/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170827/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170828/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174964/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174965/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180557/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

VADAKKEKULAMB

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170114/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170829/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170830/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174972/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.N

OD174973/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180559/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap.B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

NEAR KMAUP SCHOOL KARTHALA

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc.complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170188/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170835/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170836/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174975/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174976/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180560/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

PARANAKKULAM

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170258/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170837/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170838/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174978/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174979/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180562/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

KIZHAKKEKARA

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170353/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170842/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170843/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174981/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174982/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180563/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

MANAKKALKULAM

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170434/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170845/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170846/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174984/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174985/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180564/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

THANIYAPPANKUNNU

15.7.1 Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In mud mortar

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170532/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170850/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170851/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174987/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded. Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174988/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8”*1.5”. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer – Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron. N

OD180565/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

PAALACHUVAD

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

50.6.7.2 Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor two level including all cost of materials, labour charges etc.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

51.2.3 Filling with Quarry Muck <br> Filling up low lying and water logged areas with local material/ quarry muck, spreading in layers, leveling the top at site and consolidation by ramming, etc complete for improving the CBR value of subgrade

13.1.1 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

16.68 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

13.52.2 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On concrete work

OD170888/2025-2026 Fabrication supply conveyance and installation of Granite name board indicating the cost involved, commencement date, completion date and inaguration date etc.

OD170890/2025-2026 Supply and installation of Shoulder Twirl double Product Area : 2?10? x 1?2? Safe Area : 8?10? x 6?2? Age Group : 13 Years and above Age Group : 13 Years and above M ain frame: 100 NB G.I pipe w heel frame: 25 NB & 20 NB G.I pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD170891/2025-2026 Supply and installation of SKY TRAINER DOUBLE Of Product Area : 4.8'Ft x 4.1'Ft , Safe Area : 8.8'Ft x 8.1'Ft for Age Group : 13 Years and above .Users at a Time : 2 Nos , Main frame: 100 NB G.I B-Class pipes. -Jindal make Foot Rest pipe: 40 NB G.I B- Class pipe -Jindal make Foot Rest: LLDP Roto moulded with inbuilt bolts 3/8" x 1.5" Handle: 25 NB G.I B- Class pipe. Rubber: High quality rubber is used for handle grips. Clamps: Nylon 66 injection moulded casing Handle cover: Nylon 66 injection moulded. Bearings: Reputed make (FAG/SKF) Pipe Cap: Nylon 66 injection moulded. Nut bolts: Galvanised nut bolts Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80

OD174990/2025-2026 Supply and installation of SINGLE SURF BOARD Product area:3.7?ft*2.6?ft Safe area:7.7?ft*6.6?ft Age group:13 years and above Function:Strengthens Leg Muscles,Improves cardio vascular Endurance Main frame: 100 NB G.I B-Class pipe-Jindal make Leg frame: 40 NB G.I B-Class pipe Jindal make Handle frame: 25 NB G.I B-Class pipe Jindal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Pipe Cap: Galvanised cap. Bearing Cap: Nylon 66 injection moulded.Bearing housing and pin: Seamless pipe & Round bar Nut bolts cap: Nylon 66 injection moulded with SS M6 fasteners. Bearings: Permanant sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD174991/2025-2026 Supply and installation of CHEST PRESS CUM AIR WALKER CUM STANDING TWISTER Age group:13 years and above Users at Time:3 Nos Center frame:100 NB G.I c-class pipe-jindal make Top frame:40 NB&32 NB G.I b-class pipe-jdal make Handle frame: 32 /NB& 25 NB G.I b-class pipe-jindal make Connecting pipe:32 NB & 25NB & 40NB G.I b-class pipe-jdal make Seat& back rest: IIdp rotomoulded seat with inbuilt bolts 3/8?*1.5?. Stopper:Pu rod.50 mm dia Main frame:100 NB G.I c-ss pipe-jinke Leg frame:32 NB G.I b-class pipe-jindal make Handle frame:25 NB G.I b-class pipe jndal make Clamps: Nylon 66 injection moulded casing Foot Rest: LLDP roto moulded seat with inbuilt bolts 3/8" x 1.5" Seat frame:32 Seat frame:32 b-class pipe Handle frame:20 NB G.I b-class pipe Twister disc: lldp rotomoulded seat with inbuilt bolts 3/8" x 1.5" Pipe cap: galvanised cap. Bearing cap: cap for 100 NB- Nylon 66 injection moulded. Bearing housing and pin:seamless pipe&round bar Bearings: Permanent sealed of reputed make (FAG/SKF) Nut bolts: Galvanised nut bolts Nut bolts cap: nylon 66 injection moulded with ss m6 fasners. Powder coat: Done by first coat of Primer ? Jotun Brand 40-50 micron thickness and top coat of pure Polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

OD180566/2025-2026 Supply and installation of FUN CYCLE of Safe Area : 6?8? x 7?8? Product Area : 1?8? x 2?8? for an Age Group : 13 Years and above Users at a Time : 1 Nos M ain frame: 25 NB & 40 NB G.I b-class pipe s eat frame: 32 NB G.I b-class pipe h andle frame: 25 NB G.I b-class pipe p ipe cap: galvanised cap. B earing cap: nylon 66 injection moulded. B earing housing and pin: seamless pipe & round bar n ut bolts: galvanised nut bolts n ut bolts cap: nylon 66 injection moulded with ss m6 fastners. B earings: permanent sealed of reputed make (fag/skf) powder coat: done by first coat of primer ? jotun brand 40-50 micron thickness and top coat of pure polyester powder with 70- 80 micron thickness. Total thickness is 110-120 micron.

meconconstructions (BID ID -2391430)

Shyja Suresh K (BID ID -2392895)