ELECTRIFICATION WORKS OF TRANSFORMER PLANT,KEL, MAMALA

Amount

SWITCH BOARD

SB - 1 (Main Panel)

Supply, installation, testing & commissioning of cubicle type

Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 800

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 32 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate standards and it shall only be

manufactured after getting approval from the Electrical

Inspectorate and the consultant.

Busbar

1 Runs of 100 x 12mm AL.Busbar for each Phase

1 Runs of 63 x 12mm AL.Busbar for Neutral

EB Side

1 Nos - 800A 36kA 4P Microprocessor based MCCB with

ROM and Spreader

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 800/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

DG Side

1 Nos - 400A 36kA 4P Microprocessor based MCCB with

ROM and Spreader

1 Set RYB Indication lamps with Control MCBs

3 Nos - 400/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

Interlock

Castle Key Interlock - 2 Lock with one Key

Surge Protection Device

2 Nos - 8 Module DIN Rail Mounting Type 1 + Type 2 /

Class 1 + class II 100kA SPD on the incoming side of EB

Supply and DG Supply with all necessary accessories etc.

complete as required. The connections to RYB Phases,

Neutral and Earth shall be done using 16 Sq.mm Single Core

Flexible Copper conductor cables with less than 0.45m in

length.

Outgoings

1 Nos - 630A 36kA 4P Microprocessor based MCCB with

ROM, Spreader Digital Multifunction Meter measuring V, A,

F, KWH, KVA, PF with Control MCBs and CTs

3 Nos - 400A 36kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

2 Nos - 320A 36kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

2 Nos - 250A 36kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

SUB SWITCH BOARDS

SSB - 1 (Plant - Right Side)

Supply, installation, testing & commissioning of cubicle type

Sub Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 400

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate standards and it shall only be

manufactured after getting approval from the Electrical

Inspectorate and the consultant.

Busbar

1 Runs of 63 x 10mm AL.Busbar for each Phase

1 Runs of 40 x 10mm AL.Busbar for Neutral

Incomer

1 No - 400A, 36kA 4P Thermal Magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader &

Stunt Release

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 400/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KWH, KVA, PF with Control MCBs

1 Nos - Earth Leakage Relay with CBCT

Outgoings

1 Nos - 200A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM & spreaders

2 Nos - 160A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

2 Nos - 125A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

3 Nos - 100A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

1 Nos - 80A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

SSB - 2 (Plant - Left Side)

Supply, installation, testing & commissioning of cubicle type

Sub Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 400

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate standards and it shall only be

manufactured after getting approval from the Electrical

Inspectorate and the consultant.

Busbar

1 Runs of 63 x 10mm AL.Busbar for each Phase

1 Runs of 40 x 10mm AL.Busbar for Neutral

Incomer

1 No - 400A, 36kA 4P Thermal Magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader &

Stunt Release

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 400/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KW, KVA, PF with Control MCBs

1 Nos - Earth Leakage Relay with CBCT

Outgoings

1 Nos - 200A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM & spreaders

2 Nos - 160A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

2 Nos - 125A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

3 Nos - 100A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

1 Nos - 80A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

SSB - 3 (Testing)

Supply, installation, testing & commissioning of cubicle type

Sub Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 630

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate standards and it shall only be

manufactured after getting approval from the Electrical

Inspectorate and the consultant.

Busbar

1 Runs of 75 x 12mm AL.Busbar for each Phase

1 Runs of 50 x 12mm AL.Busbar for Neutral

Incomer

1 Nos - 630A 36kA 4P Microprocessor based MCCB with

ROM, Spreader & Shunt Release

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 630/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KW, KVA, PF with Control MCBs

1 Nos - Earth Leakage Relay with CBCT

Outgoings

1 Nos - 400A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM & spreaders

1 Nos - 200A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM & spreaders

1 Nos - 160A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

2 Nos - 125A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

3 Nos - 100A 25kA 4P Thermal magnetic type MCCB with

having 70 to 100% setting provision with ROM & spreaders

SSB - 4 (Lighting)

Supply, installation, testing & commissioning of cubicle type

Sub Switch Board Panel suitable for 415 V, 3 Phase, 4 wire,

50 Hz AC supply system having sufficient front surface area

fabricated in compartmentalised design from CRCA sheet

steel of 2mm thick for frame work and covers, 3mm thick

for gland, plates cleaning & finishing complete with 7 tank

process for powder coating in approved shade, having 250

Amps capacity extensible type TPN Aluminum alloy bus

bars of high conductivity, DMC / SMC / FRP bus bar

supports, with short circuit withstand capacity of 31 MVA

for 1 Sec., bottom base channel of MS section not less than

100 mm x 50 mm x 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common

copper earth bar of size 25 mm x 6 mm at the rear with

2 Nos. earth stud, solid connections from main bus bar to

switch gears with required size of AL. bus bars and control

wiring with 1.5 sq. mm. PVC insulated FRLSH copper

conductor cables, cable alleys etc. The panel shall conform

to Electrical Inspectorate standards and it shall only be

manufactured after getting approval from the Electrical

Inspectorate and the consultant.

Metering

4 Nos - Busbar Provision for fixing CTs

1 Nos - Provision for fixing Three Phase Energy Meter

Fuse & Neutral Link

3 Nos - 250A Bakelite/Open Type Fuse with HRC Fuse of

Suitable Rating

1 Nos - 250A Neutral Link

Busbar

1 Runs of 50 x 10mm AL.Busbar for each Phase

1 Runs of 32 x 10mm AL.Busbar for Neutral

Incomer

1 Nos - 250A 25kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader &

Shunt Release

1 Set - RYB Indication lamps with Control MCBs

3 Nos - 250/5A CL:1, 10VA CT

1 Nos - Digital Multifunction Meter measuring V, A, F,

KW, KVA, PF with Control MCBs

1 Nos - Earth Leakage Relay with CBCT

Outgoings

1 Nos - 125A 36kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

3 Nos - 100A 36kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

3 Nos - 80A 36kA 4P Thermal magnetic type MCCB

having 70 to 100% setting provision with ROM, Spreader,

Digital Multifunction Meter measuring V, A, F, KWH,

KVA, PF with Control MCBs and CTs

2 Nos - Street Light Cubicle with 40A 30mA 4P RCCB,

40A 4P MCB, 40A 3P Contactor, 24Hour Timer Switch,

Push buttons, ON (Green) - OFF (Red) Indication lamps

with Control MCBs, etc.complete as required with Digital

Multifunction Meter measuring V, A, F, KWH, KVA, PF

with Control MCBs and CTs

DISTRIBUTION BOARD

Supply and fixing of following ways surface / recess

mounting, vertical type, 415 V, TPN MCCB distribution

board of sheet steel, dust protected, duly powder coated,

inclusive of 200A tinned copper bus bar, common neutral

link, earth bar, din bar for mounting MCBs (But without

MCBs (But without MCBs and incomer) as required.

8 Way , Double Door

6 Way , Double Door

Supply and fixing of following ways surface / recess

mounting, vertical type, 415 V, TPN MCB distribution board

of sheet steel, dust protected, duly powder coated, inclusive

of 200A tinned copper bus bar, common neutral link,

earth bar, din bar for mounting MCBs (But without MCBs

and incomer) as required.

8 Way (8 + 24), Double Door

6 Way (8 + 18), Double Door

4 Way (8 + 12), Double Door

Supply and fixing of following way, horizontal type three

pole and neutral, sheet steel, MCB distribution board, 415V,

on surface/recess, complete with tinned copper bus bar,

neutral bus bar, earth bar, din bar, interconnections, powder

coated including earthing as required. (But without MCB/

RCCB/Isolator)

8 Way (8 + 24), Double Door

6 Way (8 + 18), Double Door

4 Way (8 + 12), Double Door

Supply and fixing of following way, single pole and neutral,

sheet steel, MCB distribution board, 240V, on surface /

recess, complete with tinned copper bus bar, neutral bus

bar, earth bar, din bar, interconnections, powder coated

including earthing etc. as required. (But without MCB/RCCB

/Isolator)

16 Way, Double Door

Supply and fixing following rating and breaking capacity and

pole MCCB with thermal magnetic release having 70 to 100%

setting provision and terminal spreaders in the distribution

board including making connections, etc. complete as

required.

80A to 100A 25kA 4P MCCB

Supply and fixing following rating, four pole, (three phase

and neutral), 415V, Residual Current Circuit Breaker

(RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Supply and fixing following rating, double pole, (single

phase and neutral),240V, Residual Current Circuit Breaker

(RCCB), having a sensitivity current 30 mA in the existing

MCB DB complete with connections, testing and

commissioning etc. as required.

Supply and fixing 5A to 32A rating, 240/415V, 10kA, "C "

Curve, miniature circuit breaker suitable for inductive load

of following poles in the existing MCB DB complete with

connections, testing and commissioning etc as required.

Single Pole

Double Pole

Triple Pole

40A to 63A Triple Pole

MCB DUMMY

Supply and fixing single pole blanking plate in the existing

MCB DB complete etc. as required.

ISOLATOR

Supply and fixing following rating, four pole, 415V,

isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

100A 4P Isolator

63A 4P Isolator

40A 4P Isolator

25A 4P Isolator

Supply and fixing following rating, double pole, 240V,

isolator in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

63A 2P Isolator

40A 2P Isolator

METAL ENCLOSURE

Supply and fixing Sheet Steel enclosure on surface / recess

having provision to fix MCB/Isolator complete with

connections, testing and commmissioning etc. as required.

INDUSTRIAL SOCKET

Supply and fixing 32A, 415V, TPN Industrial type socket

outlet, with 4 pole and earth, metal enclosed plug top along

with 30A/32A, 'C Curve', TP MCB, in sheet steel enclosure,

on surface or in recess, with chained metal cover for the

socket outlet and complete with connections, testing and

commissioning etc. as required.

Supply and fixing 20A, 240V, SPN Industrial type socket

outlet, with 2 pole and earth, metal enclosed plug top along

with 20A, 'C Curve', SP MCB, in metal sheet enclosure, on

surface or in recess, with chained metal cover for the

socket outlet and complete with connections, testing and

commissioning etc. as required.

DOL STARTER

Supplying, installation, testing & commissioning of DOL

Starter Switch Panel enclosure suitable for 5HP to 10HP

compressor complete with all accessories including 4P

Power Contactor, Overload Relay, ON-OFF Push Buttons,

etc. complete with wiring in duly powder coated sheet steel

enclosure.

LT CABLES

Supply, laying, testing and commissioning of PVC 1.1 KV

grade XLPE insulated armoured Aluminium cables of the

following sizes and laying in earth excavated trenches,

clamping in built up trenches, trays, racks, risers, trusses,

walls etc using heavy duty Aluminium Flat or heavy duty GI

spacer saddles of which spacing of clamps not exceeding

40cm and pulling through pipes including all minor civil

works.

3.5C x 400 Sq.mm Al. cable

3.5C x 300 Sq.mm Al. cable

3.5C x 240 Sq.mm Al. cable

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

2C x 10 Sq.mm Al. cable

2C x 6 Sq.mm Al. cable

4C x 2.5sq.mm Copper Armoured cable

2C x 2.5sq.mm Copper Armoured cable

4C x 1.5sq.mm Copper Armoured cable

2C x 1.5sq.mm Copper Armoured cable

GLANDING AND TERMINATION

Supply and making end termination with brass compression

gland and alluminium lugs for following size of PVC

insulated and PVC sheathed/ XLPE Aluminium conductor

cable of 1.1 KV grade as required.

3.5C x 400 Sq.mm Al. cable

3.5C x 300 Sq.mm Al. cable

3.5C x 240 Sq.mm Al. cable

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

2C x 10 Sq.mm Al. cable

2C x 6 Sq.mm Al. cable

4C x 2.5sq.mm Copper Armoured cable

2C x 2.5sq.mm Copper Armoured cable

4C x 1.5sq.mm Copper Armoured cable

2C x 1.5sq.mm Copper Armoured cable

GLAND EARTHING

Supply and providing gland earthing using Aluminium or

Copper strip / shim / wire using copper sockets etc.

complete as required conforming to Electrical Inspectorate

Standards.

3.5C x 400 Sq.mm Al. cable

3.5C x 300 Sq.mm Al. cable

3.5C x 240 Sq.mm Al. cable

3.5C x 185 Sq.mm Al. cable

3.5C x 150 Sq.mm Al. cable

3.5C x 120 Sq.mm Al. cable

3.5C x 95 Sq.mm Al. cable

3.5C x 70 Sq.mm Al. cable

3.5C x 50 Sq.mm Al. cable

3.5C x 35 Sq.mm Al. cable

4C x 25 Sq.mm Al. cable

4C x 16 Sq.mm Al. cable

4C x 10 Sq.mm Al. cable

4C x 6 Sq.mm Al. cable

2C x 10 Sq.mm Al. cable

2C x 6 Sq.mm Al. cable

4C x 2.5sq.mm Copper Armoured cable

2C x 2.5sq.mm Copper Armoured cable

4C x 1.5sq.mm Copper Armoured cable

2C x 1.5sq.mm Copper Armoured cable

LT CABLE JOINT

Supplying and making straight through joint with heat

shrinkable kit including ferrules and other jointing materials

for the following size of PVC insulated and PVC sheathed /

XLPE aluminium conductor cable of 1.1KV grade as

required.

3.5C x 400 Sq.mm

3.5C x 95 Sq.mm

EARTHING

Supply and providing earthing with CI earth plate 1200mm x

1200mm x 12.6mm thick electrode including accessories,

and providing masonary enclosure with cover plate having

locking arrangement and watering pipe of 2.7 meter long

etc. with charcoal/coke and salt as required conforming to

relevant IS and Electrical Inspectorate standards etc.

Supply and providing earthing with CI earth plate 600mm x

600mm x 6mm thick electrode including accessories,

and providing masonary enclosure with cover plate having

locking arrangement and watering pipe of 2.7 meter long

etc. with charcoal/coke and salt as required conforming to

relevant IS and Electrical Inspectorate standards etc.

EARTHING CONDUCTORS

Supply and providing the earth conductors of the following

sizes and laying in earth excavated trenches, clamping in

built up trenches , walls, trays, racks, risers, trusses, etc

using heavy duty Aluminium Flat or heavy duty GI spacer

saddles of which spacing of clamps not exceeding 90cm

without making holes in the earthing conductor and pulling

through pipes including all minor civil works. All the joints

should be properly tinned and connections should only be

done using SS Nut and Bolts with double washers etc as

required.

25 x 6 mm Copper Strip

25 x 3 mm Copper Strip

8 SWG Copper Wire

10 SWG Copper Wire

MS STRUCTURALS

Supply, fabrication and installation of cable tray and supports

using M.S angles and plates of adequate size painted with

one coat of Zinc chromate primer and two coats of black

enamel paint.

Supply, fabrication and installation of Panel Board mounting

supports using C Channels of adequate size painted with two

two coat of Zinc chromate primer and two coats of black

enamel paint.

Supply, fabrication and installation of checkered plates of

6mm thickness to use above the cable trenches duly

supported with channels and duly painted with two coat of

Zinc chromate primer and two coats of black enamel paint.

and as required.

PIPES FOR CABLE PROTECTION

Supply and laying of the following size medium class GI

pipe in ground/wall/ceiling complete with fittings.

50mm dia

80mm dia

100mm dia

150mm dia

Supply and laying of the following size DWC HDPE pipe

ISI marked along with all accessories like socket, bend,

couplers etc. conforming to IS 14930, Part II complete

with fitting and cutting, jointing etc. in the existing trench,

complete as required.

63mm dia

90mm dia

120mm dia

160mm dia

200mm dia

POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell

point with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium

class PVC conduit, with modular switch, modular plate,

suitable GI box / surface box and earthing the point with

1.5 sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required.

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable in surface

/recessed medium class PVC conduit, 2 way modular

switch, modular plate, suitable GI box / PVC surface box

and earthing point with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point / fan point /

exhaust fan point / call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper

conductor single core cable in surface / recessed medium

PVC conduit, and earthing the point with 1.5 sq.mm FRLS

PVC insulated copper conductor single core cable etc. as

required.

Group C

Supply and fixing two module stepped type electronic fan

regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

Supply and fixing suitable size GI box /PVC surface box

with modular plate and cover in front on surface or in

recess including providing and fixing 3 pin 5/6 A modular

socket outlet and 5/6 A modular switch, connections etc. as

required.

Supply and fixing suitable size GI box /PVC surface box

with modular plate and cover in front on surface or in

recess including providing and fixing 2 Nos. 3 pin 5/6 A

modular socket outlet and 2 Nos of 5/6 A modular switch,

connections etc. as required. (For light plugs to be used in

non residential buildings).

Supply and fixing suitable size GI box /PVC surface box

with modular plate and cover in front on surface or in

recess including providing and fixing 3 Nos. 3 pin 5/6 A

modular socket outlet and 2 Nos of 5/6 A modular switch,

connections etc. as required. (For light plugs to be used in

non residential buildings).

Supply and fixing suitable size GI box / PVC surface

box with modular plate and cover in front on surface or in

recess, including providing and fixing 6 pin 5/6 & 15/16 A

modular socket outlet and 15/16 A modular switch,

connections etc. as required

Supply and fixing suitable size GI box / PVC surface

box with modular plate and cover in front on surface or in

recess, including providing and fixing 2 Nos of 6 pin 5/6 &

15/16 A modular socket outlet and 15/16 A modular switch,

connections etc. as required

Supply and fixing following size/ modules, GI box / PVC

surface box along with modular base and cover plate for

modular switches in surface or in recess etc. as required.

1 or 2 Module

3 Module

4 Module

6 Module

8 Module

12 Module

Supply and fixing following modular switch/socket on the

existing modular plate and switch box including connections

etc. as required.

Telephone socket outlet

TV antenna socket outlet

Data socket outlet

Supply and fixing 3 pin, 5A ceiling rose on the existing

junction box/wooden block including connections etc. as

required

Supply and fixing modular blanking plate on the existing

modular plate & switch box excluding modular plate as

required.

CIRCUIT WIRING

Wiring for circuit / submain wiring along with earth wire

with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface / recessed medium

class PVC conduit as required.

2 x 1.5 sqmm + 1 x 1.5 sq.mm earth wire

2 x 2.5 sqmm + 1 x 2.5 sq.mm earth wire

2 x 4.0 sqmm + 1 x 4.0 sq.mm earth wire

2 x 6.0 sqmm + 1 x 6.0 sq.mm earth wire

4 x 6.0 sqmm + 2 x 6.0 sq.mm earth wire

4 x 10.0 sqmm + 2 x 6.0 sq.mm earth wire

TELEPHONE, TV & DATA WIRING

Supply and drawing following pair 0.5mm dia FRLS PVC

insulated annealed copper conductor, unarmoured telephone

cable in the existing surface/recessed PVC conduit as

required.

Supply and drawing co-axial TV cable RG-6 grade, 0.7mm

solid copper conductor PE insulated, shielded with fine

tinned copper braid and protected with PVC sheath in the

existing surface/recessed PVC conduit as required.

Supply and drawing of UTP 4 pair CAT 6 LAN Cable in the

existing surafce/recessed PVC conduit as required.

1 run of cable

SUPPLY AND LAYING OF CONDUITS

Supply and fixing of following sizes of medium class PVC

conduit along with accessories in surface/recess including

cutting the wall and making good the same in case of

recessed conduit as required.

STREET LIGHTING

Supply, installation, testing & commissioning of 9 meter high

hot dip galvanised Octagonal poles with double arm bracket,

155mm bottom dia and 70mm top dia made up of 3mm thick

sheet along with base plate of size 250 x 250 x 16mm.

Supply, installation, testing & commissioning of 8 meter high

hot dip galvanised Octagonal poles with double arm bracket,

130mm bottom dia and 70mm top dia made up of 3mm thick

sheet along with base plate of size 200 x 200 x 16mm.

Supply, installation, testing & commissioning of 7 meter high

hot dip galvanised Octagonal poles with double arm bracket,

130mm bottom dia and 70mm top dia made up of 3mm thick

sheet along with base plate of size 200 x 200 x 12mm.

Supply, installation, testing & commissioning of the following

Watts Graphite grey powder coated pressure die-cast

aluminium housing with weatherproof gasket for LEDs and

control gear compartments, pressure die-cast aluminium

frame with heat resistant toughened clear glass fixed with

SS screws. LEDs shall provided with secondary lens optics

to get optimum optical performance. The drivers used shall

be specially designed to have built-in surge voltage, open /

short circuit protections.Internal surge of 5 KV and External

surge protection of 10 KV provided for additional safety.

Luminaire shall have CCT of 5700, CRI >70, IP 66

protection, IK 07, PF>.95, THD <10%,operating voltage

range of 150 - 300v AC, and 120 Lumesn/watt efficiency

with a lumen package of 12000

Foundation

Providing required RCC foundation for Street Light Pole

after excavating of the soil to the required depth. The

concrete mix for PCC shall be in M:15 Grade (1:2:4) and

that of RCC shall be in M:20 Grade (1:1.5:3). The contractor

shall submit the drawings of the foundation to the Engineer/

Manager in charge and Consultant for getting approval

before the commencement of work or the work shall be

executed as per the drawings given to the contractor.

SUPPLY OF LIGHT & OTHER FITTINGS

Supply and providing the following fittings and items at site

Battern/Angle Holder

LED Bulb (up to 12W)

Industrial type LED Tube Set of 1 x 20W with Tube

Industrial type LED Tube Set of 2 x 20W with Tube

2 x 2 (2 Feet x 2 Feet) LED Light

120W LED Highbay Light

100W LED Flood Light

50W LED Flood Light

26W/28W BLDC Ceiling Fan of Sweep 1200mm with

Remote

High Speed Metal Type Exhaust Fan of Sweep 225mm

High Speed Shutter Type Exhaust Fan of Sweep 200mm

High Speed Shutter Type Exhaust Fan of Sweep 150mm

INSTALLATION OF LIGHT & OTHER FITTINGS

Installation, testing and commissioning of PVC battern /

angle holder fitting complete with all accessories directly on

ceiling/wall, including giving connections etc. as required.

Installation, testing and commissioning of pre-wired,

flourescent fitting/compact flourescent fitting of all types

complete with all accessories and tube/lamp etc. directly on

ceiling/wall, including connections with 1.5 sq.mm FRLS

PVC insulated, copper conductor, single core cable and

earthing etc. as required.

Installation, testing and commissioning of 2 x 2 (2 Feet x

2 Feet) LED Ceiling light fittings complete with all

accessories directly on the ceiling by cutting the ceiling

including giving connections etc. as required.

Installation, testing and commissioning of 120W LED

Highbay light fittings complete with all accessories directly

on ceiling, including giving connections etc. as required.

Installation, testing and commissioning of 100W LED Flood

light fittings complete with all accessories directly on wall/

piller/ceiling, including giving connections etc. as required.

Installation, testing and commissioning of 50W LED Flood

light fittings complete with all accessories directly on wall/

piller/ceiling, including giving connections etc. as required.

Installation, testing and commissioning of ceiling fan,

including wiring the down rods of standard length (up to

30cm) with 1.5 sq.mm FRLS PVC insulated, copper .

conductor, single core cable etc. as required

Installation of exhaust fan in the existing opening, including

making good the damage, connection, testing,

commissioning etc. as required.

up to 450mm sweep

FAN ROD

Supply and fixing extra down rod of 10cm legnth G.I pipe

15mm dia, heavy guage including painting etc. as required.

(Note: More than 5cm length shall be rounded to the

nearest 10cm and 5cm or less shall be ignored).

Supply and fixing extra down rod of 20cm legnth G.I pipe

15mm dia, heavy guage including painting etc. as required.

(Note: More than 5cm length shall be rounded to the

nearest 10cm and 5cm or less shall be ignored).

DISMANTLING

Labour charges for the dismantling of existing Main Panel

Board (MSB), tracing the existing cables, disconnecting and

dismantling the existing cables and connections, providing

temporary connection arrangements to existing cables if

necessary etc. complete as required.

Labour charges for the dismantling of existing 105KVAR

APFCR Panel Board, tracing the existing cables,

disconnecting and dismantling the existing cables and

connections, providing temporary connection arrangements

to existing cables if necessary etc. complete as required.

Labour charges for the dismantling of existing Lighting Panel

Board, tracing the existing cables, disconnecting and

dismantling the existing cables and connections, providing

temporary connection arrangements to existing cables if

necessary etc. complete as required.

Labour charges for the dismantling of existing any other

Switch Board/Sub Switch Board Panel, tracing the existing

cables, disconnecting and dismantling the existing cables and

connections, providing temporary connection arrangements

to existing cables if necessary etc. complete as required.

Labour charges for the dismantling of all existing DB's,

Wiring Switch Boards, Ceiling Fans, Wall Fans, Exhaust

Fans, Tube & other Light Fittings, Conduits, Wires, Ceiling

Roses etc. tracing of existing wirings, providing temporary

connection arrangements if necessary etc. complete as

required.

SAFETY EQUIPMENTS

Supply and fixing MV danger notice plate of 200 mm x

150mm, made of mild stee,l at least 2mm thick and vitreous

enameled white on both sides and with inscriptions in signal

red colour on front side as required.

Supply and fixing 2Kg Dry Chemical Powder (DCP) type

fire extinguisher complete with Gun Metal cap, hose with

squeeze grip nozzle, wall fixing brackets conforming to

BIS: 2171 and with ISI mark

Supply and fixing safety instruction chart in word duly

framed in good frame work as required.

Supply and providing a set of 2 Nos. 9.5 Litre capacity GI

bucket painted in post office red colour with prior coat of

red oxide paint and written with white paint "FIRE" and

mounted on MS angle iron frame with bracket of

appropriate size and capacity including filling sand etc.

Supply and providing First Aid Box as approved by St.John

Ambulance Brigade / Indian Red Cross conforming to

Supply and fixing laminated shock treatment chart duly

mounted on a good frame work

Supply and providing electrical grade rubber mat of size

2m x 1m having 12mm thickness in front of panels and

DBs conforming to IS 15652 : 2006 standard.

Supply and providing electrical grade rubber mat of size

2m x 1m having 6mm thickness in front of panels and

DBs conforming to IS 15652 : 2006 standard.

Supply and providing tested industrial safety helmet

conforming to IS 2925 : 1984

NAMING FOR IDENTIFICATION

Painting letters or figures of 2.5cm/4.5cm sizes with enamel

paint as identification mark to Panel boards, DBs etc as

required.

EARTH EXCAVATION AND BACK FILLING

Excavation of all types of soils for the laying of XLPE

insulated power cable, GI / HDPE / RCC Pipes, Earthing

Copper conductors to the required width and depth up to

1.2m and back filling after providing sand cushioning and

protective covering by laying bricks breadth wise above the

cable. The supply of sand and bricks will come within this

scope. The trench dimensions and specifications shall be as

per the Electrical Inspectorate, KSEB & CPWD standards.

Excavation and Back Filling

Supply and laying of Bricks

Supply and filling of sand

DOCUMENTATION

Preparation of drawings and getting approval from Electrical

Inspectorate. (*All Statutory fees shall be remitted by the

Client / Consumer or it shall be reimbursed on the

submission of supporting documents).

Submission of completion report, arranging Inpsection and

obtaining Sanction Order from Electrical Inspectorate .(All

Statutory fees shall be remitted by the Client / Consumer

or it shall be reimbursed on the submission of supporting

documents.).

Excluding GST

Note :1 All materials, Items, Equipment shall be best branded items with IS and approved by client/KEL

2:Rate should be inclusive of installation, testing and commissioning cost for all items

3.Rate should be Exclusive of GST.

4.Work should be executed as per DSR/PWD/Irrigation Dept. specification and direction of Engineer at site.

Make of Electrical equipments/materials

All electrical materials/equipments shall be of best branded items with ISI, strictly as per schedule specification

Panel Boards: CPRI certified reputed manufacturers make

MCB/ELCB/DB - L&T/LEGRAND/SCHNEIRDER or equivalent

Cables & wires - Finolex/KEI/POLYCAB/RPG/V-GUARD

Switches/Sockets/Regulators - SCHEIDER/ABB/HAVELS/LEGRAND or equivalent

Rigid PVCPipes/Casing & Capping - A-ONE/REPUTED MAKE with ISI , Precession, Balco, GEO

Cable Glands & Sockets - REPUTED MAKE , Cosmos

Indicating Lamps - TEKINIC/RISHUB/STC, L&T, Schneider or equivalent

Ceiling/Exhaust fan: Havells, Orient, Usha, Crompton Greaves, Bajaj

Push Button- L&T, Schneider, Rishabh

Detailed list of brand/make of Electrical items enclosed.

Detailed list of brand/make of Electrical items enclosed.

JOSPOWER CONROLS

YOOSAF K A

BPE BHARATH POWER ENGINEERS PVT LTD

ZEUS ELECTRIC CONTROLS

Shine Electricals