REPAIR/REPLACEMENT OF TILING, PLASTERING, JOINERY, SANITARY FITTING, CHAJJAS AND ALLIED WORKS IN ZONE II AND IV UNDER GE (WEST) BAREILLY.

M & L for non- skid ceremic light/coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile 300mm x 300 mm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and M & L for screed bed or bedding layer of mortar 15mm thick in cement mortar (1:6) for laying floor finishes including dismantling of tiles and bedding complete all as specified and directed.

M & L for non- skid ceremic light/coloured tiles 7 to 8 mm thick (Square / rectangular) area of each tile 400 mm x 400 mm as in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and M & L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6) for laying floor finishes including dismantling of tiles and bedding complete all as specified and directed.

M&L for glazed (coloured) ceramic tiles wall 200mm x 300 mm x 7mm thick on vertical faces of walls over and including M & L for 10mm thick rendering in CM (1:4) set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting and bedding complete all as specified and directed.

M&L for glazed (coloured) ceramic tiles wall 300 mm x 450 mm x 7mm thick on vertical faces of walls over and including M & L for 10mm thick rendering in CM (1:4) set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting and bedding complete all as specified and directed.

M&L for glazed (coloured) ceramic tiles wall 300 mm x 600 mm x 7mm thick on vertical faces of walls over and including 10mm thick rendering in CM (1:4) set jointed in neat cement slurry and pointed in coloured cement to match including taking down old dado/skirting and bedding complete all as specified and directed.

M&L for vitrified ceramic tiles light shade 8 -10 mm thick (square/rectangular) polished, area of each tiles 600 mm x 600 mm as in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement over and including M& L for 15mm thick screed bed 1:6 cement motar including dismantling of floor tiles and screed bed / rendering and hearthing complete all as specified and directed.

All as per serial item no 6 as above but as in vertical surfaces including dismantling of tiles and screed bed / rendering M & L for rendering 10 mm thick in cement mortar (1:4), as in backing layer complete all as specified and directed.

S&F 18 mm thick granite stone slabs mirror polished of colour and shade as approved by GE, machine cut bedded & jointed with grey cement slurry and pointed in white cement with admixture of pigment to match the shade of granite stone fixed as in steps, jambs, pillars window cills, cooking platforms & the like over and including M & L for screed bed of 15mm thick CM 1:6 etc incl dismantling of existing tiles complete all as specified and directed

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M & L for 20-25 mm thick machine cut pre polished kota stone slab flooring laid under stairs soffit area and jointed with grey cement slurry fixed with pigment to match to shade of the slab including rubbing and mirror polishing over and including M & L for 20 mm thick bedding layer of cement mortar (1:6) for laying floor finishes even and rough with and including dismantling floor, hearth or wall kota stone slab including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for 20-25 mm thick machine cut pre polished kota stone slab in riser of steps skirting, dado and pillar,landing in single piece with round nosing with three numbers of serration using as front door steps, laid over cement screed and jointed with grey cement slurry mixed with pigment to match including rubbing & mirror polishing and inclucding M & L for 10mm thick cement plaster on brick surfaces or concrete surface in cm (1:4) finished even and rough as screed dismantling of wall tile including cement mortar bedding complete all as specified and directed.

M & L for 25 mm thick providing cement concrete type B0, 1:2:4 (using 12.5 mm graded stone aggregate) as in floors, finished rough to receive floor tiles complete all as specified and as directed.

M&L for chequered cement concrete rubber moulded coloured tiles 30cm x 30cm x 25mm thick with grey cement and no pigment, set, jointed and pointed in neat cement slurry in floors over and including M & L for 15 mm thick screed bed in CM 1:6 including dismantling of existing tiles complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 , Type C1 (Using 20 mm graded stone aggregate) as in sub base, sub floors complete all as specified and directed.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment of approved design and pattern laid over a layer of M & L for 25 mm thick sand cushion including filling the joint with sand and dismantling of existing tiles complete all as specified.

M & L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and pigment of approved design and patterm laid over a layer of M & L for 25 mm thick sand cushion including filling the joint with sand and dismantling of existing tiles complete all as specified.

Demolition of un-reinforced cement concrete in ground floors and paving n.exc 15 cm thickness (below & above ground level) complete all as specified and as directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

Demolition of brick/stone masonry work built in cement mortar including all quions, arches, pillars etc complete.

M & L for brick work with old size fly ash brick, using straight or curved on plan in CM (1:6) all as specified and directed.

M & L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed.

M&L for 15 mm thick cement plaster on newly plastered bricks or concrete surfaces in CM (1:4) finishing the surface even and fair and necessary scaffolding as per requirement complete all as specified and directed.

M&L for 12 mm thick cement plaster on bricks or concrete surfaces in CM (1:6) including taking down old plaster including raking out joints, hacking for key, scrubbing down with water etc., finishing the surface even and fair and necessary scaffolding as per requirement complete all as specified and directed.

M&L for 15 mm thick cement plaster on bricks or concrete surfaces in CM (1:4) including taking down old plaster including raking out joints, hacking for key, scrubbing down with water etc., finishing the surface even and fair and necessary scaffolding as per requirement complete all as specified and directed.

M & L for rendering 5mm thick on concrete surfaces of ceiling in CM (1:3) finished including taking down old plaster, finished even and fair without using extra cement and necessary scaffolding complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coat of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer of any description complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of weather proof paint over paint over a coat of 2 mm thick putty as per manufacturer instructions of any description complete all as specified and directed.

Complete removal of existing treatment from wall surfaces and rubbing down with sand paper to have even and smooth surfaces complete all as specified and directed.

M&L for applying layer of 2 mm thick wall care putty on wall surfaces including rubbing down the surfaces with sand paper after getting dried to obtained a smooth & even surface complete all as specified and directed.

M&L for preparation of old distempered surface of walls by brushing, scrapping down smoke soot moulds by steel wire brush. and applying one coat of distemper oil emulsion distemper. Complete all as specified.

M&L for preparation of old decorated surfaces of walls by brushing, scrapping down smoke soot mouldsby steel wire brush and applying one coat of cement base paint complete all as specified and directed.

M&L for preparation of old wall surfaces brushing, scrapping down smoke soot mouldsby steel wire brush and applying one coat of exterior emulsion paint all as spd and directed.

M&L for applying one coate of exterior emulsion paint on AC sheet/Allahabad tiles in roofing including interlocking / chequred tiles and preparation of surfaces by brooming or steel wire brushing scrapping down smoke soot,moulds, moss and effloroscent salts treating oily and greasy spots including cornices etc complete all as spd and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm each and not exc. 4.00 Sqm including making good disturbed portions of wall with new or old bricks, lintel,cills, etc in CM 1:4 complete all as specified and directed.

Taking down of shutters any description exc 1.00 sqm and n. exc 2.00 Sqm each incl removing from th epremises complete all as specified and directed.

S & F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, S & F in opening as per manufacturers instructions and as directed by Engineer-in-Charge.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style)consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame as per manufacturers instructions and as directed.

S&F for 105mm x 60 mm x 1.25mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1 necessary fixing lugs, SS hinges,lock strike plate, 02 x MS bar/flat at bottom of the frameetc, including wooden texture finished paint on the frame surfacecomplete all as spd and directed.

S&F for 125mm x 60mm x 1.25 mm thick pressed steel, frames for door with one or more rebates including filing and inner surface of the frame shall be treated with a coat of bituminous paint & compaction with PCC 1:3:6 Type C1, necessary fixing lugs, SS hinges, lock strike plate, 02 x MS bar/flat at bottom of the frame etc, complete including wooden texture finished paint on the frame surface all as specified and directed.

S & F 2nd class hardwood plain, solid straight chowkhats and frames, wrought, framedrebated on the solid,rounded or chamfered, puttogether with glue pinned at joints, complete including treating theback of chowkats with coal tar black paint.

S&F for 30 mm thick Factory made flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specsified & directed.

M & L for 35mm thick glazed and skeleton shutter open rebated & prepared to receive glass, gauge etc, with sash bar edges of framing plain chamfered or rounded fitted with cut and mitered beads for securing glass including campsule mesh tightly fixed with the glazed and skelton door shutter etc, of 2nd class hard wood, members of shutters as specified in SSR Part - I Section 8 clause 8.24 (a) fitted to chowkats all as specified and directed. Note:- Campsule Mess will be measured and paid separately.

S&F for 100mm long stainless steel butt hinges complete all as specified and directed.

S&F for 150mm long aluminum anodised, barrel tower bolts of extruded section and fixed.

S&F for 200mm long aluminum anodised, barrel tower bolts of extruded section and fixed.

S&F for 150mm long Extruded aluminium alloy handles, fabricated type, anodised

S&F 150 mm long floor door stopper of aluminium alloy body and tongue, brass body and tongue with hard drawn steel spring fixed in floor complete all as specified and directed.

S&F in repairs 300mm long mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as spd and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded aggregate as in cills, coping steps, tank staging, sesmic and other similar courses, lacing courses parapet and railing upto 60cm height kneeler kerb and alike including weathering, slightly rounded or chamfered angle and throating complete all as specified and directed.

M&L painting to wood and wood based surfaces of any description exc 10cm with or girth with two coats of synthetic enamel paint over a coat of pink primer including preparation of newly or previously untreated surface all as spd and directed

S & F in repairs 4mm thick sheet glass ordinary quality fixing with putty in square n.exc 0.5 sqm in each pane all as specified and directed.

All as per item No. 53 above but figured glass, pin head type all as specified and directed.

S & F for Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete ass as specified and directed.

S&F in repairs powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality) for each shutter on three tracks or two track as reuired with stainless steel mosquito proofing and glazing shutter and including 4mm thick glass & stainless steel wire mesh 0.36mm dia & average width of aperture 1.40mm fixed with neoprene rubber gasket with aluminium beading, clips, frame made with aluminium section as appended below- (i) Window frame of minimum size : 92 mm x 38 mm x 1.5 mm thick for three tracks. (ii) 63 mm x 38 mm x 1.15 mm thick for two tracks. Note : The rate for glass & wire mesh shall not be paid separately.

M&L for in repair Aluminium grill of size of grid 75 mm x 75 mm x 5 mm thick and fixed with machine screw and all as specified and directed.

S&F for in repair Anodised aluminium window, ventilator shutters and kitchen cupboards, side hung type/ slidding type without sash bars, alumimium section weighing 0.55 kg/m including necessary joining cleats glazing clips, ruber packing, anodised aluminium snap beading screws anodised aluminium fittings such as ped stays 150mm long (1 No) hinges type B-21 100mm long (2 No) suitable handle (1 No) complete all as specified for add powder coating (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F in repair Anodised aluminium frame for doors, windows, ventilators and kitchen cupboards frame with one or more rebates including joining cleat for fixing etc. complete all as specified add for powder coating (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F in repair Anodised aluminium door shutters aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified add for powder coating (minimum thickness of powder coating 50 micron)

Repair of aluminium door/window/ ventilator/ partition wall etc of any size / any number of panels including taking down (if required) & refixing for easy closing/ opening/ tightening of hinges or changing the position of hinges, adjustment of floor door spring of hydraulic door closure, adjustment of tower bolts, sliding bolts etc changing of mortice lock complete all as specified and directed.

S&F PVC boards 18/19 mm thick any colour/ prelaminated as in cabinets incl shelves and shutters, fixed with screws and adhessive as per direction of Engr-in-Charge and, manufacturer's instructions including piano hinges, magnet catcher, handles etc. complete all as specified and directed.

S & F repair wall panelling of plastic vinyl composite of size 3050 x 254 x 8 mm thick with wooden/plane surface waterproof , termite proof, chemical resistant of light weight fixed with wooden screw with rawl wall plug complete all as specified and directed.

M&L for E-board false ceiling consisting of powder coated GI wall angle, main T and cross T of 25mmX 25 mm X 1.40 mm thick grid frame work, joist, angle/ Tee as directed and mild steel wire hook not less than 6 mm dia with arrangement for adjusting height of ceiling and including provn of 4 mm thick E- Classic board in pannel of size 600X600mm with necessary off cut including dismantling of existing false ceiling and taking down and refixing of Electric fitting carefully complete all as specified and directed.

S&F rotational moulded polythene water storage tanks tripple layer white in colour (cylindrical vertical with closed top) hoisted and fixed in position capacity 500 ltrs including dismantling of existing unserviceable water tank capacity exceeding 250 ltr and not exceeding 500 ltr complete all as specified in SSR Part I and directed

S&F rotational moulded polythene water storage tanks tripple layer white in colour(cylindrical vertical with closed top) hoisted and fixed in position capacity 1000 ltrs including dismantling of existing unserviceable water tank capacity exceeding 500 ltr and not exceeding 1000 ltr complete all as specified in SSR Part I and directed

S&F 20mm Ball valves high pressure of PTMT with epoxy coated aluminium rod and high dessity plastic ball screwed for iron pipe and fixed ( minimum weight 455 gms) all as specified and as directed.

S&F in repairs for 15 mm bore ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed (Minimum weight 210 gms complete all as specified or as directed.

S&F in repairs of 20mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed

Taking up or down 15 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for refixing or removal to store complete all as specified or as directed.

Refixing 15mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.)

Refixing 20mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.)

S&F for 15mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors incl cutting chases for concealed water tubing and making good, cutting exceeding 20cm girth where requiired complete all as specified or as directed.

S&F for 20mm bore galvanised steel water tubing with all fittings 'medium grade' and fixed complete to wall and ceiling or laid in floors incl cutting chases for concealed water tubing and making good, cutting exceeding 20cm girth where requiired complete all as specified or as directed.

S & F in repairs vetrious china wash down water closet (pedestal pattern) white compete, including connectiong drain pipe and to flush pipe anti syphonage pipe etc complete all as specified and directed.

S & F in repairs plastic water closet cover closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinges device complete all as specified and directed.

S & F in repairs vitreous china squatting pan 'Orissa pattern' size 580 x 440mm white with integral foot rest including replacement of 'P' or 'S' trap lime concrete bedding and making good floors complete all as specified and directed. Make : cera act part No S3020105 /parryware cat part No C0117CS1C /hindware cat part No 20042

S & F in repairs for PVC low level flushing cistern 10 litres capacity, syphonic action type, white, as approved including ball valve float valve and handle, flush pipe as in repair complete all as specified and directed.

S & F in repairs for vitreous china, wash hand basin white size 550 x 400 mm including brackets, chromium plated waste coupling & PVC waste pipe of 32mm dia complete all as specified and directed.

S & F for 15 mm bore pillar taps standard of PTMT fancy type any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair fancy type chromium plated brass stop valve/ angle valve type suitable for 15mm bore pipe with cast copper alloy screw down, high pressure, screwed both ends for iron pipe or for unions 15 mm bore pipe complete all as specified and directed. Make-Hindware Model No F320006, CERA Cat No :- F1017201, Kerovit Cat part No :- KA910007 & Asian Paints Cat Part No MAAC101N.

S&F in repair 15 mm bore bib tap fancy type chromium plated with flange quarter turn incl all necessary fittings complete all as specified and directed. Model : Cera model No F1014151, Hindware cat part No F440003CP Kerovit Cat Part No KB 2111004, Asian Paints Cat Part No MABC101.

S & F in repair fancy type 100mm size brass CP shower rose for fixing 15 mm pipe with or without swivel joints with 45 degree bend with flange complete all as specified and as directed. Model : Parryware Cat No T9850A1 , Cera Cat Part No :- F7020111AB, Jaguar OHS-CHR-1667

S & F in repairs 15 mm dia chromium plated wall mixture with connection for shower arrangement complete all as specified and directed. Model : Hindware Cat No F390020 , Cera Cat Part No :- F1020411, Kerovit Cat Part No KB411019 & Asian Paints Cat Part No THWM103.

S & F in repairs for cetre hole basin mixer 15 mm bore chromium plated complete all as specified and directed, Model : Hindware Cat No F200014 , Cera Cat Part No :- F2002461, Kerovit Cat Part No KB1211026

S & F in repairs PVC connections 15 mm dia & 450 mm long with PTMT nuts complete all as specified and directed.

S & F in repairs for 15 mm bore fancy type bib tap of PTMT standard any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.

S & F in repairs for PVC waste pipe of 32 mm bore for WHB and Kitchen sink etc complete all as specified and directed.

S&F for in repairs kitchen sink with drainage board made of stainless steel 1 mm thick with plugs washers and waste pipe and coupling including bedding in cement mortar on dwarf walls including brackets and connecting union to pipe overall size of sink 915 mm x 460 mm and bowl size 410mm x 330mm x 160 mm complete all as specified and directed. Model :- Parryware cat No-C853199 Cera Cat No B4711507SF, Prayag Cat No 939D.

S&F in repairs sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 590 mm x 460 mm bowl size 540 mm x 410 mm x 230 mm complete all as specified and directed. Model :- Cera Cat No B 4711501- satin finish series alma, Kaff Cat No KS610SB (R10) Marco series, Hindware Cat Part No 512451, Asian Paints Cat Part No SG24188.

S&F in repairs 32 mm dia waste coupling for wash basin and kitchen sink as specified and directed.

Demolition/ dismantling of breaking up drain pipes , AC or reinforced concrete and set in cement mortarfor 110 mm dia of pipe complete all as specified and directed.

S&F P V C (SWR) pipes of 110 mm bore single socketed in any length fixed to wall all as specified and directed.

S&F P V C (SWR) pipes of 75 mm bore single socketed in any length fixed to wall all as specified and directed.

S&F 75mm PVC (SWR) floor trap plain with grating incl jointing with solvent cement all as specified and directed.

S&F 110mm PVC (SWR) WC connector with lip ring all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore provided with or without access door all as specified and directed.

All as per item no 98 above but 110 mm bore all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or un equal 110 mm bore of any radius with access door all as specified and directed.

Demolition of reinforced cement concrete, (other than ground floors), shelves, chajjas, slabs, beams and stair case similar work carefully and matching to adjoining disturbed surfaces all as directed.

M & L for Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, beams etc complete all as specified and directed.

M & L formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete complete all as specified.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in slab, shelves and stair case, beams etc.all as specified and directed.

M&L RCC 1:2:4 type B1 using 20 mm graded aggregate as in chajjas and like all as specified and directed.

S&F in repairs 20 mm dia Stainless Steel fancy type drapery curtain rod with brackets and lattu & other connected accessories etc complete all as specified and directed.

Notes:- (a) Materials not included in sch of credit and debris from the dismantling having lowest value/Nil value shall be the property of department. The same shall be removed/ disposed or deposited by the contractor in MES stores yard of GE (West) Bareilly as directed for which no additional payment shall be made. The contracotor shall be fully responsible to safe guard these materials against losses/theft/deterioration etc till the same are deposited by him in MES Store yard (b) Tenderers may note that amount as given in schedule of credit will be deducted from the total amount to worked out the net contract sum at the time of Acceptance of tender.

Please Enable Macros to View BoQ information