PROVN OF COOK HOUSE AND DINING HALL IN PUNJAB UNDER GE DEHRADUN

Amount

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and directed.

M&L Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete, complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished surfaces of concrete complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality complete all as specified and directed.

-Ditto- all as per item No 4 above, but 6mm to 8mm dia.

-Ditto- all as here-in above 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders ®

M&L for Reinforced cement concrete (nominal mix) type B1 1:2:4 (20mm graded aggregate) in Foundations, incl rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as spefied and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam aunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. flat rough finished surfaces of concrete complete all as specified and directed.

M&L for Reinforced cement concrete (nominal mix) type B1 1:2:4 (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finished surface of concrte

M&L for Reinforced cement concrete (nominal mix) type B0 1:2:4 (12.5mm graded aggregate) in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) (using old size bricks) complete all as specified.

M&L for Brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

M&L for Cement concrete 1:2:4 B-0 (using 12.5 mm graded stone agg) in coping, bed plates and chamfered angles and throating etc complete all as specified and directed.

M&L 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and fair complete all as specified

M&L 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surface, surface finished even and fair Complete all as specified

M&L returing filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed

Removal of excavated soil n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L Hardcore of broken stone gauge exc 40mm but n exc 63mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement complete all as specified

M&L for PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate), 75 mm thick as in sub base complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in leveling course to floors complete all as specified

M&L vitrified ceramic coloured tiles 10 mm thick LIGHT SHADE (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified

M&L heavy duty endura ceramic coloured tiles 10 mm thick dark shade (square/rectangular) polished,area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete.

M&L glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specifeid

M&L for Machine cut kota stone as in skirting 15-18 thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 complete all as specifeid

M&L 18 to 20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified

M&L grinding and polishing to edges and rounding of granite kota or marble slab and smooth finishing complete all as specified and as directed

M&L factory made prepolished rubber moulded vibromatic Chequred cement concrete tiles 30cmx30cmx22-25mm thick, set jointed and pointed in neat cement slurry with grey cement and colour pigment to matc over and including 15mm thick screed bedding layer in CM (1:6) complete all as specified.

S&F Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified (Note: framed filled in cement concrete1:2:4 type B0 ( 12.5 mm stone aggregate)

S&F Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified (Note: framed filled in cement concrete1:2:4 type B0 ( 12.5 mm stone aggregate)

S & F 35mm thick second class hardwood (Golden Teak) glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 75x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-Charge

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified.

S&F stainless steel barrel tower bolts 150 mm long one piece and fixed complete all as specified

S&F stainless steel butt hinges, medium weight 100 mm long one piece and fixed with screws/welded to frame, complete

S&F stainless steel handles 150 mm long one piece and fixed with screws/welded to frame, complete

S&F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay,tower bolt etc. complete with glazing bars, dovetailed or welded complete all as specified

S&F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay, tower bolt etc.complete without glazing bars, dovetailed or welded complete all as specified

S&F factory made steel ventilator with top hung shutters including hinges with steel handle, steel peg stay, tower bolt etc.complete all as specified

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete .all as specified

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete.

S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of denisity 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification.

S&F magnetic catcher and striking plate including letting in and fixed complete.

S&F Continious (PIANO) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors, post, pipes; fixed with angle cleats or other connecting plates Fe-290 (Gde E-165 complete all as specified and directed

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and profile should match with galvalume sheet complete all as specified and as directed..

Providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, including taking down existing ceiling of any type all complete at all heights as per direction of Engineer-in-Charge.

M&L applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete.

M&L applying two coats of Synthetic paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified in SSR Part I and directed by Engr-in-Charge.

M&L for preparation of newly plastered surface of wall and applying two coat of cement base paint over a coat of primer complete all as specified

S&F vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete.

S&F 10 litre capacity PVC low level cistern ‘ white’ with inlet, float valve including brackets with 32 mm dia PVC pipe/bend 600 mm long complete.

S&F vitreous china wash hand basin white, oval type counter top of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe, waste fitting etc. complete.

S&F pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of suitable angle iron,CP brass waste coupling ,superior quality PVC waste pipe and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete.

S&F rotational moulded polyethylene water storage tanks Capacity of tank 1000 litres tripple layer, white colour, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in 15 mm bore Angle cock/stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F 15mm bore Bib taps long body cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F CP grating 100mm to 125 dia round fix on floor/ nahani trap with hole/without fixed with cement mortar, complete all as specified and directed.

S&F looking mirror mounted on decorative type PVC frame fixed to wooden plug with CP brackets screw fixed, complete all as specified .

S&F 20 mm dia brass chromium plated towel rack of 3 sets type 60cm long between flanges including pair of fixing brackets complete all as specified and directed.

S&F PVC connection 15 mm dia 450 mm long with brass fly nut at both ends complete all as specified

S&F 75 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall / laid in trenches complete all as specified and directed.

S&F 110 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall/ laid in trenches complete all as specified and directed.

Cutting into existing manholes for connecting new drains 150mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete al as specified and directed.

M&L for Point wiring with1100 Volts, grade 1.5 Sqmm. (nominal area) ,PVC insulated but unsheathed multistranded copper conductor single core FRLS cable drawn through and including non metallic medium duty rigid PVC concealed conduit (medium duty) 20mm dia or higher size complete with all accessories such as socket, elbow, junction box, bell mouth, bend, reducer etc including pressed iron/steel suction box of thickness1.2mm for mounting of switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet as top cover, and 1.5 Sqmm. (nominal area) single core FRLS,PVC insulated 1100 Volts, grade multi stranded unsheathed copper conductor cable green colour as earth wire upto common earth and connected to earth dolly including cutting chases for conduits and sinking's for boxes and making good to walls,floors etc complete all as specified and directed by Engr.-in-charge of following.

One light point controlled by one way switch.

One Cieling fan point , controlled by one way switch through Regulaor

One three pin 5 Amp socket on same board with other switches

One three pin 5 Amp socket on independent board

All as per Item No 75 mentioned here-in- before but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

S & Fix for Switch piano flush type single pole one way 230 Volts 6 Amp complete all as directed.

S & Fix for Socket outlet 3 pin , 230 Volts 5/6 Amps flush type multipurpose 5 pin complete.

Supply and fix for Socket outlet multipurpose having provision for 3 pin, 230 Volts 15/16 Amp and 3 pin, 5/6 Amp, piano flush type IS: 1239-1988 marked with valid CML No complete all as specified.

Supply and fix for Switch piano; flush type, single pole, one way, 230 Volts 15/16 Amps IS: 3854 marked with valid CML No. complete all as specified

Supply and fix for Ceiling rose, Three terminal ISI marked surface bakelite suitable for batten fitting complete all as specified

S & Fix for Lamp holder polycarbonate insulated body, with back plate suitable for batton fitting.

S & Fix for step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts, 6 Amps 120 watts .

S&F wall mounted LED tube light fitting 1x20 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed.

S&F of energy saving ,surface mounted, LED 10 watt Bulk head luminaire with decorative oval diffuser comprrising of high brightness LEDs complete all as specified and directed by Engr-in-charge.

S&F Ceiling fans complete with blades ,down rods, and accessories, 230V,1200mm sweep,340 RPM,200CMM,50Watt copper wound with suitable size of fixing arrngement to MS channel or Angle iron arms as all specified & directed directed

S&F exhaust fan,steel body AC single phase ,230 V of size 300mm sweep ,1400 RPM,1300CMM,70 watt ,Copper wound with , blades, and frame and louvers

S&F Water Storage Electric geyser ,2 KW ,230 volt AC ,25 Ltr, steel tank and all accessories with safety devices ,ISI mark, 5 Star rating

Supply and fixing in replacement for Distribution board SPN 8 Way double door, for mounting MCBs isolator, ELCBs etc factory made, IS: 13032 marked with valid CM/L No fabricated out of CRCA sheet not less than 1.2 mm thick fitted with DIN channel, neutral and earthing link and bus bar. DBs shall be semi glossy finished with epoxy polyester based powder paint sprayed and baked at high temperature, painted in seven tank process. The DBs shall be of IP 43 protection.Note:- DB and MCCB/MCB shall be of same make

Supply and fixing in replacement for Distribution Box MCB Protected Socket with sheet steel enclosure 20 A MCB DBOXX Combo DP including PLUG TOP all as specified & directed

S&Fix MCB single pole 240 volt, 10 KA, 5-32 Amp, 'C' series confirming to IS complete all as specified and directed.

S&Fix MCB SPN 240 Volt 10 KA 20- 32 Amp 'C' series conforming to IS complete all as specified & directed.

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sqmm (nominal area) drawing in and including 25 mm dia or higher medium duty PVC concealed conduit/flexible conduit where reqd and conduit accessories and fittings. Including one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 6 Sq mm as earth wire upto common earth and connected to earth dolly complete all as specified & directed.

Material and labour for earthing complete with galvanized steel plate electrodes of size 600mm x 600mm x 6mm thick buried directly in ground with earth pit not less than 2.25m deep below normal ground level with top edge of plate not less than 1.5 m below normal ground level connected to galvanized wire 4 mm earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanized iron pipe 15 mm bore (light grade) including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm dia MS bar funnel wire mesh 20 mm bore galvanized iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil complete all as shown in electrical plate No 5 of SSR part 1 including testing on completion all as specified and directed. incl demolition to existing one complete.

Supply & Laying XLPE insulated armoured heavy duty electric cable , with multi stranded aluminium conductor served with an inner sheathing of PVC type armoured with galvanized steel wire or tape and PVC sheathed 1100 volt grade,nominal cross sectional area 10 Sqmm 2 core inclu lugs and heat shrinkable PVC Sleeves on exposed surfaces & teflon tape duly insulated complete laid in trenches, ducts, drawn through pipe across the road/path/alongpoles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-charge.

Excavation in trenches not exceeding 1.5m and not exceeding 1.5 m in depth for laying of electric cableand getting out in soft/loose soil, complete all as specified and directed by Engr -in-charge

Returning, filling in excavated soil , including leveling,watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed by Engr -in-charge

Removing excavated material(soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above & starting point complete all as specified and directed by Engr-in-charge.

M&L for sand cushioning in trenches for protection of UG cable with river based sand laid dry in trenches before and after laying of cable, incl well ramming complete all as specified and directed

M&L for providing of new sub class 'B' bricks, old size, well burnt laid flat dry for protection of under ground cable complete all as specified & directed.

Supply & Laying in replacement of GI Steel tubing light grade 40 mm(2") dia including all fitting laying in trenches across road or grouting /fixing on wall for protection of cable complete all as specified and directed by Engr-in-charge.

M/s Yashwant Singh (BID ID -3129466)

MOHAN LAL GUPTA (BID ID -3106527)

IMPERIAL ENGINEERS (BID ID -3116607)

V S ENTERPRISES (BID ID -3128009)

M.K Engineers (BID ID -3119482)