Improvement of WSS to SC village Khadanal Malghota Nagan in Tehsil Baijnath Distt Kangra

Amount

Excavation in foundation trenches etc. in all kinds of soil such as pick jumper work blasting soft or hard rock or by chiselling where blasting is prohibited soft/hard rock in all lifts stacking the excavated soil as directed by the Engineer-in-charge clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-charge in all leads and lifts.

Providing and laying cement concrete 1:6:12(1cement:6sand:12 graded stone aggregate 40mm nominal size and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:4:8(1cement:4sand:8 graded stone aggregate 40mm nominal size and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:3:6(1cement:3sand:6 graded stone aggregate 40mm nominal size and curing complete excluding the cost of form work in foundation and plinth in all leads and lifts.

Providing and laying cement concrete 1:2:4(1cement:2sand:4 graded stone aggregate 20mm nominal size)and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

Suspended floors, roofs, landings and shelves and their supports, balconies,beams, girders, bressumers and cantilevers upto all floor level complete involving acomplete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Providing and laying cement concrete 1:1.5:3(1cement:1.5sand:3 graded stone aggregate 20mm nominal size)and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

In foundation, footings, basis of columns and the like and mass concrete in all leads and lifts as per direction and to the entire satisfaction of the Engineer-in-charge.

Walls (any thickness but not less than 0.10m thickness) attached pillaster, buttresses, plinth & string courses etc from top of foundaation level upto floor two level as per the direction & to the entire satisfaction of the Engineer-in-Charge.

Suspended floors, roofs, landings and shelves and their supports, balconies,beams, girders, bressumers and cantilevers upto all floor level complete involving acomplete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Prov.form work with steel plates 3.15mm thick welded with angle iron frame 30 x 30 x 5mm so as to give a fair finish including centring, shuttering,strutting & propping etc. with wooden battens and ballies, height of propping & centering below supporting floor to ceiling not exceeding 4mtr.& removal of same for insitu rainforced concrete and plain concrete work complete in all leads and lifrs and as per the directioin and to the entire satisfaction of the Engineer-in-Charge :-

Flat surfaces such as soffits & suspended floors, roofs, landing and the like. Floor etc. upto 200mm in thickness.

Vertical surfaces such as walls ( any thickness ) partition and the like including attached pillasters buttresses, plinth and string courses and the like.

Providing, Laying mild or tor steel reinforcement for RCC. Work including bending binding and placing in position complete upto floor two level Tor steel complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Steel work welded in built up section , trusses and framed work including cutting,hoisting , fixing in postion and applying a priming coat of red lead paint,In gratings framed guard bars,ladders, railling,brackets and similar work. & as per direction & to the entire satisfaction of the Engineer-in-Charge.

Providing in RCC work smooth finishing of the exposed surface with Cement mortar 1:3 (1 Cement : 3 Sand) & as per direction & to the entire satisfaction of the Engineer-in-Charge.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats)to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials with in all leads and lifts and as per the direction and to the entire satisfaction of the Engineer-in-Charge..

Providing & Fixing of SFRC manhole cover with frame having frames size of 500 mm internal dia (Medium duty). The weight of cover and frame should not less than 100 Kg. complete in all respect within all leads and lifts as per the direction of Engineer-in-Charge.

Laying, jointing and testing GMS tube light class of following diameter including to be fitting complete(earth work to be measured and paid for separately including testing of joints, within all leads and lifts as per the entire satisfaction of the Engineer-in-charge

100 mm dia

Providing and fixing C.I. Sluice valves of following diameter Kirloskar/Leader make with hand wheel as per IS:780-1984 Class-I upto 300mm dia (incluidng brass spindle as per 2906-1984 Class-II for dia >300mm dia complete with bolts nuts, rubber insertion etc. (The tail piece if required shall be mesured and paid for separately) as per diection and to the entire satisfaction of the Engineer-in-charge.

100mm dia

Brick work using common burnt clay building brick in super structure in cement mortar 1:6 (1cement:6sand) Ist class brick complete all leads and lifts to the entire satisfaction of Engineer-in-charge.

Half brick masonary Ist class common burnt clay building bricks in super structure in cement mortar 1:4(1cement:4sand) in all leads and lifts as per direction of Engineer-in-charge.

Boulder/stone filling behind retaining wall/ dry hand packed tightly compelete under lean concrete to prevent the entry of surface water with in all leads and lifts complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

Random rubble masonary/polygonal rubble masoanry (uncoused/brought to courses) with hard stone of approved qualtiy in P/F including levelling up with cement concrete 1:6:12(1cement:6sand) 12 grded stone aggregate 40mm nominal size) plinth in level in cement Mortar 1:6(1cement:6sand) in all leads and lifts.

20mm thick cement plaster in single coat on rough side of stone /brick masonry walls for interior plastering upto floor two level including arrises, internal rounded angles, in all girth chamfers and / or rounded angles and finished even and smooth in cement mortar 1:6(1cement:6sand) complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

15mm thick cement plaster in single coat on rough side of stone /brick masonry walls for interior plastering upto floor two level including arrises, internal rounded angles, in all girth chamfers and / or rounded angles and finished even and smooth in cement mortar 1:6(1cement:6sand) complete in all respect as per direction and to the entire satisfaction of the Engineer-in-charge.

6mm cement plaster to ceiling in cement mortar 1:3 (1 cement : 3 sand) finished with a floating coat of neat cement and thick coat of link wash on top of wall when dry for bearing of RCC slab and bend in all leads and lifts

Providing and fixing pressed steel doors frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges jumb lock jamb,beed and if reuired angle threshold of mild steel angle of section 50X25 mm or base ties of 1.25 mm pressed mild steel welded or regidly fixed together by mechanical means,adjustable lugs with split and tails to each jamb including steel butt hinges 2.5 mm thick with guards,lock strike plate and shock absorber as specified and applying a coat of approved steel primer after pretretment of the surface as directed by Engineer-in-Charge.

Providing second class deodar wood paneled glazed or paneled and glazed shutters for doors, windows and clerestory windows including bright finished black enameled iron butt hinges with necessary screws with second class deodar wood 40mm thick in all leads and lifts.

Providing and Fixing wire gauge shutters using GMS wire guage of IS gauge designation 85 G with wire of dia 0.56 mm for doors, windows & clerestory windows including bright finished black enamelled iron hinges with necessary screws.2nd class deodar wood.

Providing and fixing of M.S. grill of required pattern in wooden frames of windows etc with M.S. Flat square or round wire with round heads bolts and nuts or by screw plain grill as per direction and to the entire satisfaction of Engineer-in-charge.

Flush Pointing on brick work with cement mortar 1:3 (1cement 3 sand) with in all leads and lifts

Proviidng and laying brick tiles over mumty roots grouted with cement mortar 1:3 (1 cement 3 sand) over 12mm layer of cement morter 1:3 (1 cement 3 sand) and finishd neat in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6graded stone aggregate 20mm nominal size) including finishing of the top surface of concrete smooth in all leads and lifts.

Constructing course rubble hammer dressede 'U' shape open surface drain with side wall 15x22 cm in cement mortar 1:6 (1cement:6sand) and inside plastering with cement plaster 1:3 (1cement:3sand) including earth work and laying 10 cmcement concrete in 1:5:10 (1cement:5sand:10 graded stone aggregate) of 40mm nominal size and 7.5 cmcement concrete 1:2:4 (1cement:2sand:4 graded stone aggregate 20mm nominal size) and finished withfloating coat to neat cement complete as per standard design.

Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dia meters bolts and nuts and wooden plug and embedding in cement concrete block 30x10x15cm 1:3:6(1cement:3sand:6 graded stone aggregate 20mm nominal size).

Providing and fixing M.S.fan clamp (Type-I)of 16mm dia M.S. including bend upto shape with broken end in RCC. Slab door painting the exposed position of trap all as per standard design complete in all leads and lifts.

White washing with lime on undecorated walls surface (two coats)to give an even shade including throughly brooming the surface dirt dust mortar dirt and other foreign matter in all leads and lifts.

Distempering (Two coat) with oil bound washable distemper of approved brand and manufacture and of required shade on decorated wall surfaces to give an even shade , after thoroughly brushing the surface cleaning of the grease, dirt loos pieces of scales and also including preparing the surface even and sand prepared smooth.

Providing and fixing anodized alminium sliding door bolts anodized transparent for type required and bright shade with necessary screw etc. complete. 250x16mm

Providing and fixing aluminium tower bolts (Barrel type) anodized transparent or dyed to rquired shade and colour with necessary screw etc. complete in all leads and lifts. 200x10mm

Providing and fixing Aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc. complete 100mm

Painting two coats(excluding priming coat)on new wood and wood based surface with ready mixed paint brushing the give and even shade including cleaning of all dirt dust and other foreign matter and sand papering and stopping with ready mixed paint other than white in all leads and lifts.

Precast terrazzo tiles 20mm thick with marble chips of specified size) laid in floors, treads of steps and landings on a bad of 25mm average thickness of cement mortar 1:6 (1cement:6sand) jointed with neatcement slurry mixed with pigment to match the shade of tiles (wherever required ) including rubbing and polishing complete with tiles of following shades silver grey in all leads and lifts.

Ramesh Rana Govt Contractor

AMIT KATOCH

SURESH KUMARGOVT CONTRACTOR

RISHI KESH

GOKUL RAM