Balance work for Construction of Additional Accommodation at CHC Thannamandi (3rd call)

Amount

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work upto plinth level in 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).(including all lead lift carriages etc complete job)

Brick work with common burnt clay (non modular) bricks of class designation 7.5 in cement mortar 1:6 (1 cement : 6 fine sand).(including all lead lift carriages etc complete job)

Extra for brick work in super structure above plinth level upto floor V-level.(including all lead lift carriages etc complete job)

Half brick masonry with bricks of class designation 75 in foundation, plinth and superstructure upto floor V-level in cement mortar 1:4 (1 cement : 4 coarse sand). (including all lead lift carriages etc complete job)

Extra for half brick work in super structure above plinth level upto floor V-level.(including all lead lift carriages etc complete job)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars. (including all lead lift carriages etc complete job)

12mm thick cement plaster finished with a floating coat of neat cement of mix 1:3 (1 cement : 3 fine sand).(including all lead lift carriages etc complete job)

12mm cement plaster of mix 1:6 (1 cement : 6 fine sand).(including all lead lift carriages etc complete job)

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement : 6 fine sand).(including all lead lift carriages etc complete job)

15mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement : 6 fine sand).(including all lead lift carriages etc complete job)

Extra for plastering exterior walls of the height more than 10 Mtrs from ground level for every additional height of 3 Mtrs or part thereof. (including all lead lift carriages etc complete job)

Making of grove 12mm x 10mm between brick and RCC. (including all lead lift carriages etc complete job)

Add or deduct for plaster drip coarse / groove in plastered surface of moulding to RCC projections. (including all lead lift carriages etc complete job)

Making plinth protection 50mm thick cement concrete 1:3:6 (1 cement : 3 course sand : 6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth crushed. (including all lead lift carriages etc complete job)

Centering and shuttering including strutting, propping etc. and removal of form work for

Columns, pillars, piers. (including all lead lift carriages etc complete job)

Lintels, beams, plinth beams.(including all lead lift carriages etc complete job)

Suspended floors, roofs, landings and access platforms.(including all lead lift carriages etc complete job)

Stairs (excluding landings) except spiral stair cases. (including all lead lift carriages etc complete job)

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5m, for every additional height of 1 mtr. of part thereof (Plan area to be measured). Suspended floors, roofs landing, beams and balconies (Plan area to be measured). (including all lead lift carriages etc complete job)

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. (Make Armocreate of SWC Chryso France) consisting of (a) applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks / brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining was upto 300mm height including rounding of junction of walls and slaps. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg / sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. (iv) Finishing the surface with 20mm thick joint less cement mortar of mix 1: 4 admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying glass fiber cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300mm / sq 3mm deep. (e) The whole terrace so finished shall be flooded with water far a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurras as 65mm (including all lead lift carriages etc complete job)

Providing and laying water proofing treatment (Make Armocreate of SWC Chryso France) to vertical and horizontal surface of depressed portions of W.C., kitchen and the consisting of (i) Ist course of applying cement slurry @ 4.4 kg /sqm mixed with water proofing compound conforming to IS : 2645 in recommended proportions including rounding of junctions of vertical and horizontal surface. (ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportions including rounding of junctions of vertical and horizontal surface. (iii) III course of applying blown or / residual bitumen applied hot at 1.7 kg per sqm of area. (iv) Ivth course of 400 micron thick PVC sheet (Overlaps at joints of PVC sheet should be 100mm wide and pasted to each other with bitumen @ 1.7 kg/sqm.(including all lead lift carriages etc complete job)

Providing and laying glossy finished full-body vitrified premium quality floor tiles of 60x60cm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make of Somany, Kajaria, NITCO and Orient make in colours and shade Ethnic-Berlinetta White, Crown White, Dacia White, Dacia Green, Dacia Pink, Dacia Ivory, Dacia Grey, Dacia Brown, Dacia Pearl, Dezzling White, Evalia, S&P Grey, S&P Brown, Ultra White, Haze Grey and Border of Royale- Crown Mint, Crown Pink, Crown Snow, Micra Brown and Radiant- Lawrence Gold, Lawrence Bianco, Lawrence Grigio, Lawernce Moka, Lawrence Jaisalmer, Nuvro Brown, Nuvaro Mocha, Nuvaro Grey, Nauvaro Nero, Nuvaro Crema, Nuvaro Bianco, Nuvaro Beige laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with matching Epoxy etc. complete.(including all lead lift carriages etc complete job)

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut flamed (pre moulded and pre polished), machine cut for stairs steps and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. (including all lead lift carriages etc complete job)

Providing and laying 16mm thick Granite of any colour and shape (area of slab upto 0.5 Sqm) gang saw cut mirror polished (pre moulded and pre polished), machine cut for kitchen platform, vanity counters window sills facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to give high gloss finish etc. complete at all levels. (including all lead lift carriages etc complete job)

Extra for providing edge moulding to 18mm thick Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge.(including all lead lift carriages etc complete job)

Extra for providing opening of required size and shape for wash basins/kitchen sink in kitchen platform, vanity counters and similar location in marble / stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing and fixing ceramic glazed floor tiles (non-skidding) 300x300mm (thickness to be specified by the manufactures) of Ist quality conforming to IS : 13755 of NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour such as white, Ivory, Grey, Fume Red, Brown laid on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc. complete(including all lead lift carriages etc complete job) .

Providing and fixing Ist quality ceramic glazed tiles conforming to IS : 13753 of minimum thickness 9mm of approved for wall cladding make like NITCO, ORIENT, SOMANY, KAJARIA or equivalent make in colour and shades Somany, Kajaria, NITCO and Orient make in colours and shade Super Deluxe, Slip Shield, Aegis Beige, Brown, Aegis Grey, Aegis Nero, Armor Blue, Armor Brown, Armor Verde, Champion Beige, Champion Crema, Champion Grey, Champion Nero, Fence Brown, Fence Crema, Fence Grey, Fence Nero, Foster, Ridge Bianco, Ridge Moka, Vigor of size 60x60cm as approved by Engineer in charge in skirting, risers of steps and dodos over 12mm thick bed of cement mortar 1:3 (1cement : 3coarse sand) and jointing with grey cement slurry @ 3.3Kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (including all lead lift carriages etc complete job)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately) sal wood(including all lead lift carriages etc complete job)

Providing & fixing glazed shutters 35mm thick for doors, windows and clear story windows using 10Kg/Sqm (4mm thick) glass panes including stainless steel but hinges of size 75mm x 62mm x 2mm of make Kitch, Arch, Blum with necessary stainless screws in second class deodar wood. (including all lead lift carriages etc complete job)

Providing and fixing 35mm thick wire gauze shutters using galvanized M.S. wire gauge of average width for aperture 1.4mm in both direction with wire of dia 0.63mm for doors, windows and clerestory windows with hinges and necessary screws in second class deodar wood. (including all lead lift carriages etc complete job)

Providing and fixing of glass panes weighing 13.75 kg/sqm (5.5mm thick) with deodar wood fillets. (including all lead lift carriages etc complete job)

Providing and fixing ISI marked 35mm flush door shutters conforming ti IS: 2202 (Part 1) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both face of shutters including ISI marked M.S pressed bright finished butt hinges with necessary screws of required size(including all lead lift carriages etc complete job)

Providing and fixing aluminium tower bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. (including all lead lift carriages etc complete job)

150x10mm. (including all lead lift carriages etc complete job)

200x10mm. (including all lead lift carriages etc complete job)

Providing and fixing aluminium handles ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. (including all lead lift carriages etc complete job)

125mm. (including all lead lift carriages etc complete job)

100mm. (including all lead lift carriages etc complete job)

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion. Single socketed pipes of 110mm diameter.(including all lead lift carriages etc complete job)

Providing and fixing on wall face unplasticised-PVC moulded fitting / accessories for unplasticised- rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap for thermal expansion (including all lead lift carriages etc complete job)

Coupler 110mm. (including all lead lift carriages etc complete job)

Single tee with door 110 x 110 x 110mm.(including all lead lift carriages etc complete job)

Bend 87.5* 110mm. (including all lead lift carriages etc complete job)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC / neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge (glazing and paneling to be paid for separately) (3.15mm or 10 gauge).(including all lead lift carriages etc complete job)

For fixed portion using Powder coated aluminium (minimum thickness of powder coated 50 microns).(including all lead lift carriages etc complete job)

For shutters of doors, windows and ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coated 50 microns).(including all lead lift carriages etc complete job)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item). With glass panes of 5.50 mm thickness (weight not less than 12.50 kg/sqm). (including all lead lift carriages etc complete job)

Providing and fixing 12mm thick prelaminated three layer medium density (exterior grade) particle board Grade-I, Type-II conforming to IS : 12823 bonded with phenol formaldehyde synthetic resin, of approved brand and manufacture in paneling fixed in aluminium doors, windows shutters and partition frames with C.P brass / stainless screws etc. compete as per architectural drawings and directions of Engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides. (including all lead lift carriages etc complete job)

Providing and fixing aluminium sliding door bolts ISI marked (anodized anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 300x16mm. (including all lead lift carriages etc complete job)

Providing 40x5mm flat iron hold fast 40cm long including fixing to frame with 10mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). (including all lead lift carriages etc complete job)

Providing and fixing aluminium hanging floor door stopper ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper. (including all lead lift carriages etc complete job)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS:6315 marked for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge with brass cover plate. (including all lead lift carriages etc complete job)

Providing and fixing fly proof stainless steel grade 304 wire gauze with 0.5mm dia wire and 1.4mm wide aperture in aluminium door, window, ventilator shutters and partition etc. with PVC / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item).(including all lead lift carriages etc complete job)

Providing and fixing false ceiling (ceiling tiles mineral fibre and ceiling 8821 of diamond make) at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25mm widex 1.6mm thick with flanges of 27mm and 37mm at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastner 12.5mm dia x 40mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts and bolts of required size and other end of angle hanger fixed with G.I channels 45x15x0.9mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick buttom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall / partition with the help of rawl plugs at 450mm centre to centre, with 25mm long drive all screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5x25mm at 230mm C/C, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufactures specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of Engineer-in-charge.

Applying priming coat with ready mixed pink or grey of primer of approved brand and manufacture on wood work (hard and soft wood). (including all lead lift carriages etc complete job)

Painting with synthetic enamel paint of approved brand and manufacture to give and even shade two or more coats on new work (Wood work).(including all lead lift carriages etc complete job)

Painting with ready mixed synthetic enamel paint of approved brand and manufacture in all shades to give an even shade (two or more coats) on new steel work. (including all lead lift carriages etc complete job)

P/F stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, including welded, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered including fixing accessories such as nuts, bolts, fasteners etc.(including all lead lift carriages etc complete job)

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approve steel primer all complete (fixed to openings/wooden frames with rawl plugs, screws etc.). (including all lead lift carriages etc complete job)

Providing and fixing of 12mm thick GRC wall Cladding (Tiles) of pattern stone castle (size 4” x 10”) on exterior wall / surface. Unistone make as per the approved sample. All complete as per architectural drawings and the directions of Engineer-in-Charge. (including all lead lift carriages etc complete job)

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacture,over the plasterted wall surface to prepare the surface even and smooth complete

White washing with lime to give an even shade. New work (three or more coats)(including all lead lift carriages etc complete job)

Finishing wall with acrylic smooth exterior paint of required shade on New work (two or more coats applied @ 1.67 litre/10 sqm over and including base coat of water proofing cement paint applied @ 2.20kg/10sqm)(including all lead lift carriages etc complete job)

Distampering with first quality acrylic washable distemper (ready made) of approved manufacture and of required shade/colour complete as per manufacturer's specification (two or more coats on new work)(including all lead lift carriages etc complete job)

Providing and fixing water closet squatting pan (Indian Type W.C Pan) with 100mm sand cost iron P or S trap, 10 ltrs low lewel PVC flushing cistern including flush pipe (Hindware make Cat No. 20070/ Kerovit make Cat No. 606) Manually controlled device (Handle lever) conforming to IS : 7231, with all fitting and fixture complete including cutting and making good the wall and floows wherever required. Orissa Pan white viterous china pan of size 580x440mm with integral type footrests.(including all lead lift carriages etc complete job)

Providing & fixing of white vitreous China pedestal type water closet (European Type) with cistern (A/PHAS-100 +Cat No. 201100 + Cat No. 21054) with CP bolts, nuts, CI chair hanging arrangements, bakelite seat & cover with CP hinges & rubber buffers, CP brass screw, washer with all accessories with WC connector with Rubber Lip / Buffer and side gap filled with silicon sealant wherever required. Including brass / SS screws and washer complete including cutting, making good the walls, floors, slab wherever required as per direction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing & fixing of white vitreous China under counter oval wash basin / circular basin (Hindware 10080) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B + Parko1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing and fixing of white vitreous china wash basin with pedestal (Hindware Cat No. 1008 + Pedestal Cat No. 11003) with CP brass waste assembly, CP cast brass bottle trap with extension piece (Jaquar Cat No. 769B+Parko 1535 or approved equivalent), 450mm long CP copper connections pipes (Jaquar Cat No. 803B or Parko 1535 or approved equivalent), wall flanges and rubber adapters for waste connection complete including CI/MS brackets duly painted, nuts, washers, cutting and making good the walls floors wherever required as per direction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing and fixing CP single liver extended basin mixer (height 85mm) without Popup waste system with 450mm long Braided Hoses and brass nuts with all fittings and accessories as per direction of Engineer-in-charge (Jaquar FUS 290238).(including all lead lift carriages etc complete job)

Providing & fixing white vitreous china flat back urinal with automatic flushing systems (Hindware 60021) comprising of all plumbing, electronic and electrical items, CP brass flush pipe with CP brass elbow, CP brass spreader, CP wall flange, infrared photo cells, eyes, electrically operated solenoid valve, step down transformer, equipment and any other item required to provide satisfactory functioning including necessary wall cutting/ chasing and making good, as required for urinal flushing complete as mentioned above as per direction of Engineer-Incharge. (including all lead lift carriages etc complete job)

Providing and fixng C.P hand spray with lever control (health faucet) (Jaquar Cat No. ALDCHR-565) and flexible hose 1 Mtr long connection with C.P holder for hand spray complete in all respects as per direction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing and fixing C.P brass angle valve for basin mixer and geyser points of approved quality conforming to IS : 8931 a) 15mm nominal bore (Make Jaquar FUS 29053). (including all lead lift carriages etc complete job)

Providing and fixing C.P brass robe hook (Jaquar Cat No. CAN 1191N) or approved equivalent) fixed to wall / door with plastic rawl plugs and C.P brass screws including cutting and making good the walls wherever required as per direction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing and fixing recessed liquid soap dispenser with glass bottle (Jaquar Cat No. ACN 1135 N) as per direction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing and fixing of Soap Dish Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat No. ACN 113 N).(including all lead lift carriages etc complete job)

Providing and fixing of Tumbler Holder with all fittings as per direction of Engineer-in-charge (Jaquar Cat ACN 114 N).(including all lead lift carriages etc complete job)

Providing and fixing Bottle Trap (Jaquar Cat No. ALD. 769L) and other ancillary fittings. Cutting and making good the walls wherever required compete as per directions of Engineer-Incharge.(including all lead lift carriages etc complete job)

Providing and fixing complete set of sanitary fixtures for handicapped toilets, Hindware Cat. No. 70002) comprising of EWC –P, Cistern, Seat Cover, Twin Flush Fittings Wash Basin 450X300, Half pedestal, 1 faucet with spatula lever, 1 hinged rail and 2 grab bars, including cutting and making good the walls and floors wherever required complete as per directions of Engineer in charge.(including all lead lift carriages etc complete job)

Providing and fixing 6mm copper backed float glass mirror MODI / SAINT-GOBAIN including 6mm thick BWR type ply board, 40mm stainless steel channel plugged to wall, hard wood treated with two coats of wood preservative etc. all complete as specified and shown in drawing complete to the satisfaction of Engineer-in-charge.(including all lead lift carriages etc complete job)

Providing and fixing brass towel Ring Round with Round Flenge of approved make complete with all fittings (Jaquar Cat No. ACN 11021 BN).(including all lead lift carriages etc complete job)

Providing and fixing of glass shelf 600m long with all C.P fittings of approved quality complete item (Jaquar Cat No. ACN 11071 N).(including all lead lift carriages etc complete job)

Providing and fixing 15mm dia C.P brass bib cock with wall flange of approved quality conforming to IS standard (Jaquar Cat No. 29037).(including all lead lift carriages etc complete job)

Internal work:- Exposed on wall Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps, including cutting and making good the walls etc.(including all lead lift carriages etc complete job)

32mm dia. Nominal bore(including all lead lift carriages etc complete job)

40mm dia. Nominal bore(including all lead lift carriages etc complete job)

25mm dia. Nominal bore (Hot water supply)(including all lead lift carriages etc complete job)

Conceal Inside the walls:- Providing and fixing Conceled pipe including painting with anti corrosive bitumastic paint, cutting chases and making good the wall.(including all lead lift carriages etc complete job)

20mm dia. Nominal bore(including all lead lift carriages etc complete job)

20mm dia. Nominal bore (Hot water supply)(including all lead lift carriages etc complete job)

External work Providing and fixing G.I. Pipes complete with G.I. Fittings and clamps, including cutting and making good the walls etc.(including all lead lift carriages etc complete job)

20mm dia. Nominal bore(including all lead lift carriages etc complete job)

25mm dia. Nominal bore (including all lead lift carriages etc complete job)

32mm dia. Nominal bore (including all lead lift carriages etc complete job)

40mm dia. Nominal bore (including all lead lift carriages etc complete job)

Supplying thermal insulation over hot pipes with 6mm thick "Kaiflex" or Careflex or approved equivalent thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber having density of 60-90 kg/m3 over pipes of following sizes including all required accessories complete as per manufacture's specifications and finishing it as per site requirement with cement plaster of 1:3 (1 cement: 3 coarse sand).(including all lead lift carriages etc complete job)

20mm dia 9mm thickness(including all lead lift carriages etc complete job)

25mm dia 9mm thickness(including all lead lift carriages etc complete job)

Earthwork in all kinds of soil excavation by manual means in trenches for foundations, drains, pipes, cable etc. (not exceeding 1.5 in width) and for shafts, wells, cesspits and the like not exceeding 10 Sqm on plan, depth upto 1.5 Mtr including disposal of excavated earth upto 1 Mtr from cutting edge, disposed earth is to be levelled and neatly dressed. (including all lead lift carriages etc complete job)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level in 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate) 40mm nominal size crushed. (including all lead lift carriages etc complete job)

Providing and laying in position of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size) excluding the form work cost.(including all lead lift carriages etc complete job)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in foundation and plinth in cement mortar 1:4 (1 cement : 4 fine sand).(including all lead lift carriages etc complete job)

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete TMT bars.(including all lead lift carriages etc complete job)

Providing and fixing un-plasticised PVC pipe clips of approved design to un-plasticised un-plasticised rain water pipes by mean of 50X50X50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.(including all lead lift carriages etc complete job)

75MM pipe (including all lead lift carriages etc complete job)

110MM pipe (including all lead lift carriages etc complete job)

160MM pipe(including all lead lift carriages etc complete job)

Construction brick measonery man hole in cement motor 1:4 (1 cement: 4 Coarse Sand) R.C.C top slab with 1:2:4 mix (1 cement: 2 Coarse Sand: 4 graded stone aggrigate 20 mm nominal size) foundation concrete aggrigate 40 mm Nominal Size, in side palstering 12mm thick with cement mortor 1:3 (1 cement:3 Coarse sand) finshed with floating coat near cement and making channels in cement concrete 1:2:4 (1 cement:2 Coarse snad:4 graded stone aggirgate 20mm nominal size) finished with floating coat of neat cement complete as per standard design. inside size 90cmx80cm and 45cm deep including cast iron cover with frame (light duty) 455x610mm internal dimensionals. total wt. of cover and frame to be not less than 38kg (wt. of cover 33kg and wt.of frame 15kg) with F.P.S bricks of class designation 75 (crush stone aggrigate) (including all lead lift carriages etc complete job)

Constructing masonry Chamber 60 x 60 x 75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 fine sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chain lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. (With F.P.S. bricks) (including all lead lift carriages etc complete job)

Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of approved design including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge. (Size 100 mm dia) (ISI Marked)(including all lead lift carriages etc complete job)

Providing and fixing heavy class SS grating plane including setting in floor with cement motor to match with floor finish as per direction of Engineer-Incharge (Size 100 mm dia) (ISI Marked) (including all lead lift carriages etc complete job)

Centering and shuttering including strutting, propping etc. and removal of form work for (including all lead lift carriages etc complete job)

Slab (including all lead lift carriages etc complete job)

Wall (any thickness) including attached plaster etc. (including all lead lift carriages etc complete job)

15mm cement plaster on the rough side of single or half brick wall of mix in 1:4 (1 cement : 4 fine sand). (including all lead lift carriages etc complete job)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank (Sintex, Electroplast, star, Lotous or equivalent having valid ISI license) (1000 ltr. Capacity 15 No.). (including all lead lift carriages etc complete job)

Making soak pit 2.5m diameter 3.0 M deep with 45x45cm dry brick honey comb shaft with bricks of class designation 75mm and S.W. drain pipe 100mm diameter 1.8 m long complete as per standard design with FPS bricks. (including all lead lift carriages etc complete job)

Supply, assembly, erection, testing and commissioning of pumping system comprising the following: Vertical/Horizontal centrifugal pumps (1 Working + 1 Stand-by) with mechanical seal, SS Volute casing and SS impeller connected to suitable capacity TEFC induction motor suitable for 415 ± 10 % volts, 3 phase, 50 cycles A.C. supply with 100 mm dia. pressure gauges including MS skid and mounting of the pumps on the skid. (Motor to be of the same make as the pump) Pump Capacity 180 lpm, at 30 m head (1 working + 1 standby) (Domestic water relift pump).(including all lead lift carriages etc complete job)

M/S QAZI MUSHTAQ SON