SPECIAL REPAIR/ REPLACEMENT OF LT DISTRIBUTION PANELS AND CONNECTED ITEMS AT VARIOUS LOCATION OF HQ SWAC, VSN CHILODA UNDER GE (AF) CHILODA

Amount

Supply, installation, commisioning and testing factory made and tested, CPRI approved, LT feeder pillar box (KISOK), indoor type, mounted on rigid angle iron frame, suitable size, having independent compartment for insulated aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 2.00 mm thick CRCA sheet suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with aluminium bus bar of 2000 Amp rating for 3 phase and neutal 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, Cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coating in siemens grey colour front & rear opening type with double door shutter and locking arrangement including provision of 65 mm Godrej (freedom) lock with 2 keys, suitable aprons for cable entry/ exist, including taking down and refixing of exisiting cable properly with lugs and thimable, rate including for removal and taking out existing old/ rusted LT panel board of any type any size complete all as approved and comprising as under:-

(d) MCCB 4 pole, current rating 250 Amp, with thermal magnetic release, breaking capacity 35 kA at 415 V, 50 Hz - 04 Nos. (e) MCCB 4 pole, current rating 160 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 02 Nos. (f) MCCB 4 pole, current rating 100 Amp, with thermal magnetic release, breaking capacity 16 kA at 415 V, 50 Hz - 03 Nos. (g) MCB SPN current rating 32 Amp, breaking capacity 10 kA at 230 V, 50 Hz - 02 No. (h) Angle iron base frame as reqd size as per above panel, total leg height 600mm and grouting in side PCC 150 mm legs and made out of ISA 5050, 75 x 75 x 10 mm thick angle iron duly painted - 01 No. (j) M&L for necessary excavation and as reqd PCC (1:3:6) type C2 (using 40mm graded stone aggregates) for foundation of angle iron legs frame work complete - 01 Job.

Supply, installation, commisioning and testing factory made and tested, CPRI approved, LT feeder pillar box (KISOK), indoor type, mounted on rigid angle iron frame, suitable size, having independent compartment for insulated aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 2.00 mm thick CRCA sheet suitable for 3 phase 415 Volts, 50 Hz, AC supply, bus bar chamber with aluminium bus bar of 1200 Amp rating for 3 phase and neutal 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coating in siemens grey colour front & rear opening type with double door shutter and locking arrangement including provision of 65 mm Godrej (freedom) lock with 2 keys, suitable aprons for cable entry/ exist, including taking down and refixing of exisiting cable properly with lug and thimable, rate including for removal and taking out existing old/ rusted LT Panel board of any type any size complete all as approved and comprising as under:-

(d) MCCB 4 pole, current rating 160 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 04 Nos. (e) MCCB 4 pole, current rating 100 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 02 Nos. (f) MCCB 4 pole, current rating 63 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 01 Nos. (g) MCB SPN current rating 32 Amp, breaking capacity 10 kA at 230 V, 50 Hz - 02 No. (h) Angle iron base frame as reqd size as per above panel, total leg height 600mm and grouting in side PCC 150 mm legs and made out of ISA 5050, 75 x 75 x 10 mm thick angle iron duly painted - 01 No. (j) M&L for necessary excavation and as reqd PCC (1:3:6) type C2 (using 40mm graded stone aggregates) for foundation of angle iron legs frame work complete - 01 Job.

Supply, installation, commisioning and testing factory made and tested, CPRI approved, LT feeder pillar box (KISOK), outdoor type, mounted on rigid angle iron frame, suitable size, having independent compartment for insulated aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 3.00 mm thick CRCA sheet suitable for 3 Phase 415 Volts, 50 Hz, AC supply, bus bar chamber with aluminium bus bar of 500 Amp rating for 3 phase and neutal 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, common earth bus bar of GI Strip 32 x 6 mm at bottom with panel board at two earth terminals, cable glands with independent plates at bottom for each outgoing and in coming cables in cable alley and complete board painted with powder coating in siemens grey colour front & rear opening type with double door shutter and locking arrangement including provision of 65 mm Godrej (freedom) lock with 2 keys, suitable aprons for cable entry/ exist including taking down and refixing of exisiting cable properly with lug and thimable, rate including for removal and taking out existing old/ rusted LT Panel board of any type any size complete all as approved and comprising as under:-

(d) MCCB 4 pole, current rating 63 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 02 Nos. (e) MCB SPN current rating 32 Amp, breaking capacity 10 kA at 230 V, 50 Hz - 03 Nos. (f) Angle iron base frame as reqd size as per above panel, total leg height 600mm and grouting in side PCC 150 mm legs and made out of ISA 5050, 50 x 50 x 6 mm thick angle iron duly painted - 01 No. (g) M&L for necessary excavation and as reqd PCC (1:3:6) Type C2 (using 40mm graded stone aggregates) for foundation of angle iron legs frame work complete - 01 Job.

Supply, installation, commisioning and testing factory made and tested, CPRI approved, LT feeder pillar box (KISOK), outdoor type, mounted on rigid angle iron frame, suitable size, having independent compartment for insulated aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 3.00 mm thick CRCA sheet suitable for 3 phase, 415 Volts, 50 Hz, AC supply, bus bar chamber with aluminium bus bar of 800 Amp rating for 3 phase and neutal 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, common earth bus bar of GI strip 32 x 6 mm at bottom with panel board at two earth terminals, cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coating in siemens grey colour front & rear opening type with double door shutter and locking arrangement including provision of 65mm Godrej (freedom) lock with 2 keys, suitable aprons for cable entry/ exist including taking down and refixing of exisiting cable properly with lug and thimable, rate including for removal and taking out existing old/ rusted LT panel board of any type any size complete all as approved and comprising as under:-

(d) MCCB 4 pole, current rating 63 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 04 Nos. (e) MCCB 4 pole, current rating 40 Amp, with thermal magnetic release, breaking capacity 25 kA at 415 V, 50 Hz - 03 Nos. (f) MCB SPN current rating 32 Amp, breaking capacity 10 kA at 230 V, 50 Hz - 03 Nos. (g) Angle iron base frame as reqd size as per above panel, total leg height 600mm and grouting in side PCC 150mm legs and made out of ISA 5050, 50 x 50 x 6 mm thick angle iron duly painted - 01 No. (h) M&L for necessary excavation and as reqd PCC (1:3:6) type C2 (using 40mm graded stone aggregates) for foundation of angle iron legs frame work complete - 01 Job.

Supply, installation, commisioning and testing factory made and tested, CPRI approved, LT feeder pillar box (KISOK), outdoor type, mounted on rigid angle iron frame, suitable size, having independent compartment for insulated aluminium bus bar, incoming feeder and each out going feeder, dust and vermin proof, factory made, fabricated out of not less than 3.00 mm thick CRCA sheet suitable for 3 phase 415 Volts 50 Hz, AC supply, bus bar chamber with aluminium bus bar of 400 Amp rating for 3 phase and neutal 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators - 01 Set, cable glands with independent plates at bottom for each out going and in coming cables in cable alley and complete board painted with powder coating in siemens grey colour front & rear opening type with double door shutter and locking arrangement including provision of 65 mm Godrej (freedom) lock with 2 keys, suitable aprons for cable entry/ exist including taking down and refixing of exisiting cable properly with lug and thimable, rate including for removal and taking out existing old/ rusted LT panel board of any type any size complete all as approved and comprising as under:-

M&L for earthing complete in repairs with galvanised steel earth electrode 60 cm x 60 cm x 6 mm burried directly in ground vertically to a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below ground level connected to and including galvanised earth lead as GI strip of 32X6mm dia by means of bolts, nuts, check nuts and washer etc. made of galvanised iron and connected to earthing test point all as shown in electrical plate No. 3 of SSR Part I 2009 and as specified or indicated and testing on completion including excavation/ earth work in any type of strata, PCC (1:3:6) type C1 earthing chamber, precast RCC slab 50 mm thick in reinforced cement concrete (1:2:4) type B1 reinforced with welded steel wire fabric (XPM jali weight not less than 4 Kg/ Sqm), cast iron frame, funnel with wire mesh, 40mm bore medium grade, GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc. complete all as specified and as directed. Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. Any addition in length shall be adjusted through deviation order. (ii) Necessary excavation work is included in this item.

Taking down/ out underground cable of aluminium conductor of 10 to 35 Sqmm of any core after disconnecting from sheet metal encloser/ panel board or from OH line and taking out from trenches including taking out brick cable cover complete all as specified and as directed. Note:- Excavation, earthwork, will be measured and paid separately under respective items of this schedule.

Taking down/ out underground cable of aluminium conductor of 50 to 95 Sqmm of any core after disconnecting from sheet metal encloser/ panel board or from OH line and taking out from trenches including taking out brick cable cover complete all as specified and as directed. Note:- Excavation, earthwork, will be measured and paid separately under respective items of this schedule.

Taking down/ out underground cable of aluminium conductor of 120 Sqmm of any core after disconnecting from sheet metal encloser/ panel board or from OH line and taking out from trenches including taking out brick cable cover complete all as specified and as directed. Note:- Excavation, earthwork, will be measured and paid separately under respective items of this schedule.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm, 4 Core complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm, 4 Core complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm, 3.5 Core complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 Sqmm, 3.5 Core complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 70 Sqmm, 3.5 Core complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 Sqmm, 3.5 Core complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 120 Sqmm, 3.5 Core including taking down of old cable complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

Supply and laying of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 11000 Volts grade with stranded aluminium conductor of size 95 Sqmm, 3 Core including taking down of old cable complete all as specified and as directed. Note:- Excavation/ earth work will be measured and paid separately.

S&F in repair cable jointing kit for 11000 Volts grade cable for outdoor termination joints, heat shrinkable type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm, 3 Core complete all as specified and as directed.

S&F in repair cable jointing kit for 11000 Volts grade cable for Indoor termination joints, heat shrinkable type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm, 3 Core complete all as specified and as directed.

S&F in repair cable jointing kit for 11000 Volts grade cable for straight through joints, heat shrinkable type joint complete with jointing material and accessories suitable for XLPE armoured aluminium conductor cable of size 50 Sqmm to 95 Sqmm, 3 core complete all as specified and as directed.

M&L for laying in trenches in road cross/ floors tube galvanished iron light grade pipe of 40mm bore with all fittings for protection of cable complete all as specified and as directed.

All as per Item No. 21 above but 50mm bore pipe.

All as per Item No. 21 above but 80mm bore pipe.

Labour only for boring under road/ drain by manual method for inserting the light grade pipe GI tubing upto 80mm dia for cable protection complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m width and not exceeding 1.5 m in depth and getting out in soft/ loose soil for taking up/ laying cable/ pipe etc. complete all as specified and as directed.

Returning, filling in trenches, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose soil complete all as specified and as directed.

Removal of excavated material at a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point in soft/ loose soil complete all as specified and as directed.

Supply and laying dry sand cushioning to underground cable with screened, washed river sand, including punning gently complete all as specified and as directed. Note:- Thickness after punning will be measured for payment.

Supply and laying for burnt brick old size sub class 'B' laid in trenches abutting each other with a gap not exceeding 10mm, vertically over the cable for cable protection complete all as specified and as directed.

Supply and laying reinforced precast concrete cable cover, class LV cover, type 1 with peak, size 250mm x 150mm x 40mm complete all as specified and as directed.

Supply and laying reinforced precast concrete cable cover, class HV cover, type 1 with peak, size 300mm x 180mm x 40mm complete all as specified and as directed.

S&F in replacement MCCB 400 Amps, 4 pole, 415 Volt grade, AC 400 Amp 36 KA and Ics = 100% of Icu with adjustable thermal release including taking down old unserviceable MCCBs complete all as specified and as directed.

All as per Item No. 32 above but MCCB FP 250 Amp, adjustable type, 36 KA.

All as per Item No. 32 above but MCCB FP 200 Amp, adjustable type, 36 KA .

All as per Item No. 32 above but MCCB FP 100 Amp, fixed type, 25 KA.

All as per Item No. 32 above but MCCB FP 63 Amp, fixed type, 16 KA.

Dismantling and taking down unserviceable flood lights fitting of any type, any description and any capacity from any height of wall, roof and pole complete all as specified and as directed.

S&F 200 Watt LED flood light (cool white/ warm white) with pressure die cast aluminium housing, complete with all accessories, energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP 66 flood light with high power LEDs as light source, suitable for highlighting architectural facade highmast and general purposelighting W Turo Floodlight luminaires with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion and IP 66 Protection fixed in existing clamp and connecting with existing cable, including nuts, bolts and washer etc. complete all as specified and as directed by Engr-in-Charge.

S&F150 Watt LED flood light (cool white/ warm white) with pressure die cast aluminium housing, complete with all accessories, energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP 65 flood light with high power LEDs as light source, suitable for highlighting architectural facade highmast and general purposelighting W Turo Floodlight luminaires with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion and IP 66 Protection fixed in existing clamp and connecting with existing cable, including nuts, bolts and washer etc. complete all as specified and as directed by Engr-in-Charge.

S&F 100 Watt LED flood light (cool white/ warm white) with pressure die-cast aluminium housing, complete with all accessories, energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP 65 flood light with high power LEDs as light source, suitable for highlighting architectural facade highmast and general purposelighting W Turo Floodlight luminaires with secondary optics made in pressure die cast housing and heat sink in aluminium extrusion and IP 66 Protection fixed in existing clamp and connecting with existing cable, including nuts, bolts and washer etc. complete all as specified and as directed by Engr-in-Charge.

S&F cable jointing kit, heat shrink type for 1100 Volts grade cable for straight through joints with jointing material and accessories suitable for LT armoured aluminium conductor cable of size 185 to 300 Sqmm, 3.5 Core complete all as specified and as directed

S&F cable jointing kit, heat shrink type for 1100 Volts grade cable for straight through joints with jointing material and accessories suitable for LT armoured aluminium conductor cable of size 70 to 150 Sqmm, 3.5 Core complete all as specified and as directed

S&F cable jointing kit heat shrink type for 1100 Volts grade cable for straight through joints with jointing material and accessories suitable for LT armoured aluminium conductor cable of size up to 50 Sqmm, 3.5 Core complete all as specified and as directed.

TECH SERVE SOLUTIONS

Abhishek Enterprises

ALBA AC AND REF SERVICES

SATISH ELECTRICALS