TN No.19_04

Amount

Road Works: Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (i) By Manual Means (A) In area of non thorny jungle

Construction of embankment with material obtained from Borrow Pits with a lift upto 1.5m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000m as per technical specification clause 301.5 (i) Private Land

Furnishing and laying of live sods of perennial turf forming grass on embankment slope, verges or other locations shown on the drawing or as directed by the Engineer including preparation of ground, fetching of roads and watering

(A) Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (ii) For Grading II Material

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for three year.

(B) Semi Reflective Traffic Signs I. Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 iv) 800mm x 600 mm rectangular

(B) Semi Reflective Traffic Signs I. Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 ii. 60 cm equilateral triangle

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC :8 fixing in position including painting and printing, etc. as per drawing and technical specification clause 1703. ii) Ordinary kilometre stone (Precast)

Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC :8 fixing in position including painting and printing, etc. as per drawing and technical specification clause 1703. iii) 200m stone (Precast)

CD Works 2cell x 2m x 2m: Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. I. Ordinary Soil

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 I. Sand filling

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 B. With natural Gravel I. P.C.C Grade M10 Nominal mix (1:3:6)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 B. With natural Gravel IV. R.C.C Grade M20

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 B. With natural Gravel III. P.C.C Grade M20

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 B. With Natural Gravel IV. RCC Grade M 25 i) For height upto 5 m

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in substructrue complete as per drawings and technical specification Clauses 1000 & 1202

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From (Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX or equivalent) in foundation complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 I. Granular material

Plain/reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 800, 1205.4 and 1205.5 B. With Natural Gravel II. RCC Grade M 25 i) For height upto 5 m

Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From (Other ISI approved TMT reinforcement bar (SAI/BISCON/THERMAX or equivalent) in foundation complete as per drawings and technical specification Clauses 1002, 1010 & 1202

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 A. With crushed stone

Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900 and 1208.3

Providing and laying curtain walls complete as per drawing and technical specification Clause 1304 iii. Cement concrete grade M 10

Drainage spouts complete as per drawing and technical specifications Clause 1209

Construction of flexible apron 1 m thick comprising of loose stone boulders weighing not less then 40 kg beyond curtain wall

CD Works HPC: Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. I. Ordinary Soil

Plain cement concrete M10 (1:3:6 nominal mix) in levelling course to below open foundation of head walls as per drawing & Technical Specification Clause 1109.

Brick masonry work in cement mortar in foundation of head walls complete excluding II. Brick masonry in 1:4 cement mortar

Providing and laying reinforcement cement concrete pipe NP3 for culverts on first class B. 1000 mm dia

Plastering with cement mortar (1:4) 15mm thick on brick work in sub-structure as per

CD Works 1cell x 1m x 1m: Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. I. Ordinary Soil

Fillling in foundation trenches as per drawing and technical specification Clause 305.3.9 I. Sand filling

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 B. With natural Gravel III. P.C.C Grade M20 Nominal mix (1:2:4)

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 B. With Natural Gravel IV. RCC Grade M 25 i) For height upto 5 m

Supplying, fitting and placing TMT reinforcement (Fe-415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 B. With Natural Gravel

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 A. Granular material

SPT Bridge No.1/1: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

SPT Bridge No.1/2: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

SPT Bridge No.2/1: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

SPT Bridge No.3/1: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

SPT Bridge No.3/2: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

SPT Bridge No.10/1: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

SPT Bridge No.11/1: Labour for dismantling all members of the timber bridge (except piles) and stacking them at suitable places as directed (all members will be under the custody of the contractor till taken over by the Deptt.).

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile actually driven under ground

Supplying and driving sal pipes 25cm to 30cm dia. Dressed to heart wood including marking length in every 30cm interval, coal tarring two (2) coats with best tar applied hot (Rate inclusive of the cost of the required quantity of tar) With pile engine Portion of pile remaining above ground

Supplying, fitting and fixing timber beam and bearing beam rectangular in size fitted with M.S. etc. supplying spikes etc. as necy. and coal tarring two (2) coats with best tar applied hot as directed (Rate is inclusive of the cost of the required quantity of tar.) Using Sal Timber

Supplying, fitting and fixing "U" shaped flat iron strap making 0.5mx0.3m size from 50mm x 12mm size MS flat including providing 10 bolts holes and fitting with 0.35m long 20mm dia MS bolts including fitting tightly with bearing beam pile and RSJ beams etc. as directed by the department.

Labour for fitting and fixing RSJ beam, old CI saddle etc. in position includig necy scaffolding and fixing necy bolts and nuts, painting two (2) coats complete (Tar- Steel paints to be supplied by the contractor as his own cost.)

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) i) Undressed in floor planks, collars, bracing, standards, wheel guards struts and railing, runner belts, rails, posts etc.

Sal work including supplying, fitting and fixing complete with necy M.S. bolts, nuts, nails, screws etc. and coal tarring two (2) coats with best tar applied hot (Rate is inclusive of the cost of the required quantity of tar.) ii) In track way planks (alternate nailing to be done with decking in a staggered way)

Making 120 cm wide bamboo foot bridge with 100m Bhboluka or Barua bamboo post driven 120cm to 180cm underground 3 nos in each row and rows being 3m apart bholuka or barua bamboo dham placed over the post tied with cane or wire bholuka bamboo struts long gorhs closely packed and tied with dham single layer of mat placed over 75mm thick brush wood and tied with Bholuka or Barua bamboo rails stand fixed in one side of the bridge etc. complete.

GAUTAM BRAHMA

SAKENDRA BASUMATARY