Harnessing of Bore Wells by way of providing various electro-mechanical works at various spots in Asham of District Bandipora.

Amount

Providing, installation, testing and commissioning of Three phase submersible pumping units and allied works for installation in various wells of following specifications: Pump: Dia. of Well Casing = 125mm Discharge of the Pump = 210 LPM Dynamic Head Range = 55-60 Meter Speed = 2850 RPM Mat. Of the impeller = Noyrl/cast steel Efficiency = Not less than 45 % Shaft Material = Stainless Steel Fluid to be handled = Clear water Motor: Rating = corresponding to head & discharge Frequency = 50Hz Working Voltage = 415 Votls - 15% +6% Efficiency = Not less than 45 % The job also includes: 1. Fabrication, providing & fitting of suitable dia. GI nipple cum reducer as per outlet of above submersible pump duly threaded up to suitable length and other end for membering with column pipe as per site requirement. 2. Fab. of mild steel crate belt around the pump motor including all allied works at site. 3. Providing & fitting of 50 mm dia. long elbow duly threaded and socketed at top of well casing. 4. The job also includes extraction of existing 01 no single phase pumping unit from well along with all pipes, cables, valves etc up to tank and re installation of same material at new site to be provided by concerned DDC or kept as standby, which shall be the discretion of DDC.

Providing, installation, testing and commissioning of Three phase submersible pumping units and allied works for installation in various wells of following specifications: Pump: Dia. of Well Casing = 125 mm Discharge of the Pump = 140 LPM Dynamic Head Range = 55-60 Meter Speed = 2850 RPM Mat. Of the impeller = Noyrl/cast steel Efficiency = Not less than 45 % Shaft Material = Stainless Steel Fluid to be handled = Clear water Motor: Rating = corresponding to head & discharge Frequency = 50Hz Working Voltage = 415 Votls - 15% +6% Efficiency = Not less than 45 % The job also includes: 1. Fabrication, providing & fitting of suitable dia. GI nipple cum reducer as per outlet of above submersible pump duly threaded up to suitable length and other end for membering with column pipe as per site requirement. 2. Fab. of mild steel crate belt around the pump motor including all allied works at site. 3. Providing & fitting of 50 mm dia. long elbow duly threaded and socketed at top of well casing.

Fabrication, providing and fitting of 50 mm split type MS clamps of required size. The job includes the cost of required size of nuts and bolts.

Fabrication, providing & fitting of 50 mm Dia. medium class socketed GI column pipe pieces. The job includes the cost of cutting/threading of each column on both sides. Each length of column pipe is to be of 3 Meter long included is cost on account of providing, fitting of desired size heavy duty GI socket to each joint after 10 feet length up to ground level. Pipe material shall be with all BIS codes.Make Jindal, Surya Prakash make. (for various sites) (to be installed in three wells)

Providing & fitting of 8 mm sq. multi stranded steel wire to be fastened with well top up to pumping unit in well to avoid detachment of pumping unit in case of failer of threaded joint. (to be installed in 03no of wells)

Providing and Fitting of 12 N0. D-clips for holding/ gripping/fastening of above steel wire. (to be installed in Two no wells)

Fabrication, providing & fitting of 125 mm dia. MS/Steel Well cap. The job includes flushing of 50 mm dia. Hole in the center of cap for column pipe.

Design, manufacturing, providing, erection, testing and commissioning of 1 MT capacity overhead tripod systems made out of 65 mm dia. MS/GI class B pipe 20 feet long each leg. The job includes providing and fitting of top and bottom plates, MS rod of required dia., machine holes to be drilled on the top for holding of pipes at one end including shelling wire to be fitted in to the rod for holding of chain pulley block. Providing and finishing by buffing, primary coat of red oxide fallowed by enamel steel paint in case of MS to whole tripod with approved shade.

Providing, fitting and testing of 1 MT capacity chain pulley block with 6 mtr lift of in duf Make.

Providing and Fitting of 1 MT capacity Polyester flat double ply webbing sling.

Providing and Fitting of 25 sq. mm, 3.5 Core, XLPE Armored Aluminum Cable conforming to IS: 7098 part 1st as service line from LT feeder to Main MCCB including necessary thimbling, crimping, taping etc. Make Havells, National,Polycab. (to be installed at three wells)

Providing and fitting of 3-Core flat 6 mm Square submersible copper cable conforming to IS:694 (Part 1st) – 1964 & IS: 694 (Part 2nd) - 1964 for connecting Submersible Pumping Unit with starter. The cable connection terminals shall be fittedwith copper thimbles and taping of required size. (to be installed in three wells)

Providing, installation , testing and commissioning of three phase fully Automatic Star Delta Starter pump controller in sheet steel enclosure / switch gear protection equipment for submersible pumping unit having following accessories to be fitted: 1. MCB-----16 Ampere 3 pole 2. AC Power contactor---380-415 V---18 A 3. Over load relay----6-9 A/as required 4. Meters with CT coils----VAF/MFM 5. Single phase preventer 6. Indicators----3 No 7. Terminal block/connector---asrequired 8. Push button-------2 No 9. Including necessary interconnections, Thimbles etc. as required and is to be fitted on the wall with nut bolts. (for three sites)

Design , Supply , installation and Testing of 7 KVA ,Three phase voltage stabilizer with fallowing salient feature : Voltage Range…….. ( 90 Volts---420 Volts ) copper wound with adequate insulation , core is of cold rolled high silicon steel laminations held together by steel clamps, its material should have minimum core losses but maximum strength , hysteresis losses are minimum and temperature not to exceed 70 degree centigrade , Regulator to be of Bakelite sheet plate type with copper contacts with 5 boosting steps capable to with stand double the rated current for a considerable period of time, the container be of M S sheet strong enough to hold the entire weight and shall accommodate complete core , windings ,regulator and T-oil which shall be filled up to required level , 07 no 0f brass poles be fitted at the top for input , output and neutral. The top of the tank shall have a display panel fitted with voltmeters 0-500v --- 02 no for input & output, steel wheels be fitted to the bottom for easy positioning on floor. The job includes testing of unit on full load to be installed at three sites.

Design , Supply , installation and Testing of 5 KVA ,Single phase voltage stabilizer with fallowing salient feature : Range---- ( 90 v---240 v ) copper wound with adequate insulation , core should be of cold rolled high silicon steel laminations held together by steel clamps, its material should have minimum core losses but maximum strength , hysteresis losses be minimum and temperature not to exceed 70 degree centigrade , Regulator to be of plate type Bakelite sheet with copper contacts with 5 boosting steps capable to with stand double the rated current for a considerable period of time, the container be of M S sheet strong enough to hold the entire weight and shall accommodate complete core , windings ,regulator and T-oil which shall be filled up to required level , 04 no 0f brass poles be fitted at the top for input , output. The top of the tank shall have a display panel fitted with voltmeters 0-500v --- 02 no for input & output, steel wheels be fitted to the bottom for easy positioning on floor. The job includes testing of unit on full load at the discretion of site in charge. Make approved ISI.(for existing site)

Earth work excavation by manual means in trenches for foundation (not exceeding 1.5 m in width ) and not exceeding 10 Sqm. on plan , including dressing of sides and reaming of bottom lift up to 1.5 m , including getting out excavated earth and disposal of surplus excavated earth as directed.(for three sites)

Cost-in-situ Providing and laying (1:3:6) grade cement concrete 20 mm nominal stone aggregate including carriage of material up to site as per requirement including curing but excluding the cost of centering, shuttering and finishing with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size.(for three sites)

Fabrication, Providing, Erection and Fitting of 10’ including 3‘ underground height and 5.5’x5.5’ size steel structure shed out of following steel sections as per site requirement: Fabrication of above steel structural involves execution of trench, bottoming to vertical posts, including MS bottom plates, diagonals. crosses etc as per site requirement. 1. Vertical posts 4 No made out of 80 mm MS sq tubes 4mm thick 10 feet long.=12.19x3 Meter 2. ISA 40x40x5 steel for belting, crosses etc 3. ISA 35x35x4mm for door 2.5’x6’ 4. Flat MS strip 25x3 mm for door. 5. Any other steel section if required at site shall be used. (The top of the shed shall be fixed with MS plate 16 SWG for flooring for PVC tank over the channels.=2.32x3 Sqm. If required at the time of work execution and is on the discretion of DDC concerned, other wise sample tress is to be fabricated) The job includes fabrication of doors with providing and fitting of heavy duty MS hinges, lock handle etc required at site. The work is to carried out at site by shifting of material, oxyacetylene gas plant, welding DG set and allied tools as per site requirement, the work shall be carried out by highly skilled welder. (for three sites) (Quantity of steel may vary at the time of execution)

Providing and fixing of SMP coated sheets of Blue colour comprising 0.50 mm thick class 3 sheets fixed to the above structure as covering including door area with hooks, GI limpet and bitimunous washers, nuts or Nails etc. (for three sites). (Quantity of steel may vary at the time of execution).

Providing and applying of Painting. as per departmental colour coding prevalent with primary coat of red oxide to above steel structure and fallowed by paint.

Providing, Laying and Fitting of 50 mm dia. GI medium class pipes from well top elbow up to near by disposal point provided by DDC concern as per requirement including trench excavation work and back filling. The job includes the cost on account of providing and fitting of GI elbows, unions, sockets, Tee & reducer, Nipple required for laying and fitting of pipe including cutting and threading of pipes as per site requirement. Make Jindal, Surya Prakash or any approved make. (for three sites)

M/S EURO LIGHT ENTERPRISES (BID ID -2167037)

M/s Sopore Engineering Works (BID ID -2167437)