Road from BRTF to Siki Putu

Amount

SH: Formation Cutting.

Excavation for roadway in soil using Machanical means for carrying of cut earth to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3

Excavation in ordinary rock using machanical means including loading in a truck and carrying of excavated material to embankment site with a lift upto 1.5 m and lead upto 50 m as per Technical Specification Clause 302.3.5.

Excavation for roadway in hard rock (requiring blasting) by drilling, blasting and breaking, trimming of bottom and side slopes in accordance with requirements of lines, grades and cross-sections, loading and disposal of cut rock with a lift upto 1.5 m and leads upto 1000 m as per Technical Specification Clause 302.3.5

Collecting, sorting and stacking blasted or hand broken hard rock in measurable stack at site of work as directed by engineer- in-charge within a lead of 50m and lift upto 1.5m(payment to be made from stacked measurements after deducting 20% for voids

Deduct for Salvage Materials from Roadway Rock Cutting. (i)Credit for excavated rock found suitable for use(considering 50% of Quantity is retrievable)

SH: SHOULDER PREPARATION

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as

SH: Granular Sub Base

Construction of granular sub base by providing well graded material spreading in uniform , compacting with rollaron OMC to achieve desired dencity complete as per specification and clause 401. For Grading - I material.

SH: WBM-III.

Providing , laying , spreding and compacting stone aggregates of specific size to water bound macadam specification i/c spreding of uniform thickness , hand pcking . rolling with smooth wheel roller 80- 100 KN in stages to proper grade and camber , applying and brooming stone screening / binding materials to fii-up the interstic of coarse agg. watering and compacting to the required density grade -III as per technical clause 405.

SH: Prime Coat.

Providing and applying of prime coat with bitumen emulsion(SS-1) on prepared surface of granular base i/c clearing of base surface and spraying emulsion at the rate of 1.2-1.50 kg per sqm. using mechanical means as per technical specification clause 502 (low porosity).

SH: Tack Coat

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

SH: PMC

Providing, laying and rolling of open graded primix carpet of 20 mm thickness composed od 13.20 mm to 5.60 mm aggrigate either using penetration grade bitumen or emulsion to required line ,gradeand level to serve as wearing course on a previosly prepared base i/c mixing in a suitable plant with 80-100 KN rolling capacity finished to required level and grade to be followed by seal coat.BITUMEN S-65

SH: Seal coat

Providing, laying and rolling of seal coat to sealing voids in a bitumenous surface laid to the specified grade and cross fall using typ-A, typ-B as per tech specf.

SH: Hume pipe culvert 1000 mm dia 12 Nos

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.Ordinary soil Upto 3 m depth

Type A (Concrete Cradle) Bedding Laying concrete cradle bedding with M15 Grade Cement Concrete as per Clause 1105 (i)

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single Row. Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 Coursed Rubble masonry ( 2nd sort ) In 1:5 cement mortar

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Backfilling in Foundation Trenches as per drawing and technical specification Clause 1108

SH: Slab Culvert 4 mtr. span 2 Nos

FOUNDATION

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and back filling in trenches with excavated suitable materials. I. Ordinary soil (i) upto 3 m depth

Providing Concrete for plain/reinforced concrete in open foundations complete as per drawings and techanical specifications Cluse 802,803,1202&1203 (I) PCC grade M 10 (ii) Nominal mix 1:3:6

Stone masonry work in cement mortar in foundations complete as per drawing and techanical specifications Clauses 702,704,1202&1203. I. Course Rubble masonery (2nd Sort) in 1 : 4 CM (1 cement : 4 fine sand)

Stone masonry work in cement mortar for substructure complete as per drawing and techanical specifications Clauses 702,704,1202&1204. I. Course Rubble masonery (2nd Sort) in 1 : 5 CM (1 cement : 5 fine sand)

BackFilling behind abutment, wing wall and return wall complete as per drawing & techanical specification Clause 1204.3.8 (I) (Grannular Meterial)

Providing weepholes in stone masonary RCC work, wing wall etc 100 dia AC pipe extending through the full width of the structures with slope of 1(V) :20(H) towards drawing face complete as per drawing and

Providing & laying reinforced cement concrete in superstructure complete as per drawings and technical specification Clauses 800,1205.4 and 1205.5 (II) RCC M 15

Providing PCC M-20 architectural coping on the top of wing wall, return wall etc. complete as per drawing and technical specification Clauses 615, 710 and 1204.3.11

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Sub-Head : 15 MTR BRIDGE

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.(a) upto water level.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 I. P.C.C grade M 10 Nominal mix 1:3.6

Providing and laying reinforced cement concrete in substructure as per drawing and technical specifications Clauses 802, 804,805,806,807,1202 & 1204 for P.C.C grade M 20 (i) For Nominal mix 1:2:4 (hand mix)

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 With Granular material

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Supplying, fitting and placing with MS bar reinforcment (Fe 415) in substructure as per drawing and techanical specification Clauses 1002,1005,1010&1202

RETURN WALL

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side

Providing concrete for plain/reinforeced concreete in open foundation complete as per drawings and techanical specification clause 802,803,1202,1203 (PCC grade M 10 1:3:6)

Providing and laying reinforced cement concrete in substructure as per drawing and technical specifications Clauses 802, 804,805,806,807,1202 & 1204 for P.C.C grade M 20 (i) For Nominal mix 1:2:4 (hand mix)

Providing weepholes in stone masonary RCC work, wing wall etc 100 dia AC pipe extending through the full width of the structures with slope of 1(V) :20(H) towards drawing face complete as per drawing and techanical specification Clauses 614,709.1204.3.7

Supplying, fitting and placing with MS bar reinforcment (Fe 415) in substructure as per drawing and techanical specification Clauses 1002,1005,1010&1202

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification clause 305.3.9 (I) Granular material

DECK SLAB

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5. R.C.C grade M 20 (i) For Nominal mix 1:2:4 (hand mix)

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying cement concrete wearing course M30 grade including reinforcement complete as per drawing and techniical specifications Clause 800 & 1206-3

Drainage spouts complete as per drawing and technical specification clause 1209.

Providing and laying of a buried expansion joint, covered with 12mm thick,200mm widw galvanise weldable structural steel plate as per IS: 2062, placed symmetrical to center line of the joint,resting freely over the top surface of the deck concrete,welding of 8mm dia, 100 mm long galvanised nails spaced 300mm c/c along the centervline of the plate,as per technical specifications clauses 1207.2.3

Construction of RCC railing of M 25 grade in cast-in-situ with 20mm nominal size aggregate, true to the line and grade,tolerance of vertical railing post not to exceed 1 in 500. Center to center spacing between vertical post not to exceed 2000mm as per drawing and technical specification clauses 800,900 and 1208.3

Retaining wall

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side and bottom and back filling in trenches with excaveted suitable material. (I) Ordinary Soil (i) upto 3 m depth.

Providing concrete for plain/renforced concrete in open foundations complete as per drawing and technical specification clouse 802, 803, 1202 & 1203. I. PCC Grade M10 (ii) Normal mixed 1:3:6 (hand mixing)

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 (I) Coursed Rubble masonry ( 2nd sort ) (ii) In 1:4 cement mortar

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204 (I) Coursed Rubble masonry ( 2nd sort ) (iii) In 1:5cement mortar

Back filling behind abutment, wing wall and return wall complete as per drawing and technical specification, clouse 1204.3.8.i. Granular material

Gabion Structure

Earth work in excavation in foundation and trenches etc. in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into sides of plinth, sides of foundation etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 30 m.

Providing and laying wire created boulder structures boulder size 22.5 cm to 45 cm having 25 kg average weight for each i/c dumping/laying in S.W.G. Wire mesh of 10 cm x 10 cm (woven diagonally) 4mm dia i/c packing with small size stone spalls and carrying of boulders from a lead of 50 mtr and lift up to 1.5 mtr i/c lying properly the mesh by cutting the mouth and hoisting of wire where felt necessary as per direction of Engineer-inCharge technical specifications Clause 1301. ( Based on SDB Rural Road Chapter-14, Item No.14.2)

Earthen Drain

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side

SH: C.C. DRAIN.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of side. Clause 1604

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 a) Nominal mix 1:3:6

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. (I) Random Rubble masonry (i) In 1:3 cement mortar

Cement Plaster 15 mm thick 1:4 on stone masonry

Neat cement punning

SH: TRAFFIC SIGNS, MARKINGS AND OTHER ROAD APPURTENANCES

Kilometre Stone. Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703

i)5th Kilometer Stone (Precast)

ii)Ordinary Kilometer Stone (Precast)

iii)200 m stone (precast)

Providing and Fixing 'Logo' of PMGSY Project. Providing and fixing of typical PMGSY Citizen informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Providing and fixing of typical PMGSY Citizen information sign board as per MORD specifications and drawing of cast-in-situ RCC,(Size of RCC post 25cmx25cmx90cm below G.L. & 15cmx15cmx245cm above G.L.),(Size of board 2x 90cmx80cmx7.5cm, ) incl.earth work, finishing with 15mm pluster 1:4 and neat cement punning, applying priming coat, painting and lettering with appropiate colour with required shade of approved quality ready mix paint.

Retro-reflectorised Traffic Signs. Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801.

Provision and fixing of traffic signs for limited period at suitable locations in construction zone comprising of warning zone,approch transition zone,working zone and terminal transition zone with a minimum distance of 2-3 from the edge of the carriage way. the bottom edge of the lowest sign plate to be not less than 2m above the road level,fixed on600mmx699mmx6mm angle iron post, founded and installed as per approved design and drawings,removed and disposed of after completion of construction work,all as per IRC:SP:55-2001.

Men at work.

Do not enter.

Speed limit

Road closed

Traffic sign ahead

SH: Routine Maintenance

First Year

Second Year

Third Year

Fouth Year

Fifth Year

Add GST @ 12%

M/S H.B ENTERPRISES

K.K. Enterprises

M/s.Nima Enterprises