CONSTRUCTION OF SHOPPING CUM OFFICE AT SURENDRANAGAR FOR SURENDRANAGAR MUNICIPAL CORPORATION (SNMC) (2nd Attampt)

SCHEDULE -B ABSTRACT SHEET

Schedule No. Description of Work Amount Put to Tender

Schedule- B1 Civil Work

Schedule- B2 Plumbing

Schedule- B3 Electrical

Schedule- B4 FFTG

TOTAL TENDER COST IN (Rs.)

Estimated Amount

Rs………………………. Sub total amount put to the

Rs………………………. Sub total amount put to the

Sub total amount put to the tender

Sub total amount put to the tender

Deduct…………. % below Rs………………………. Add…………. % above

Net Rs………………………. Net

Note-1 All work shall be carried out as per public works department hand book

and other specifications as per tender or as directed by Engineer in

Note-2 Rates quoted include clearance of site (Prior commencement of work and

at its close) in all respects and hold good for work under all conditions,

site, moisture, weather etc.

Signature of Contractor with Stamp Surendranagar

Municiple Corporation

Bid Documents for Construction of Shopping Complex Cum Office at Surendranagar

Sr. No. Description Total Qty Unit Rate Amount

Excavation for foundation up to 1.5 M Depth including sorting out and stacking of useful materials and

1 disposing of the excavated stuff up to 50 meter lead 4400.00 Cum 117.08

(A) Loose or soft soil >0.00 mt. to 1.50 mt. Depth

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and stacking of useful

2 materials and disposing off the excavated stuff upto 50 Meter lead.(A) Loose or soft soil 3150.00 Cum 129.81

>1.50 mt. to 3.00 mt. Depth

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- hand broken stone

3 aggregates 40 mmnominal size) and curing complete including cost of formwork in (A) Foundation and 300.00 Cum 2956.23

Plinth (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of

4 formwork and including reinforcement for reinforced concrete work in (A) Foundations, footings, Base of 800.00 Cum 4494.61

columns and Mass concrete. (upto 10 ton)

Providing and laying controlled cement concrete M.250 and curing complete including the cost of

5 formwork and including reinforcement for reinforced concrete work in (A) Foundations, footings, Base of 200.00 Cum 7221.20

columns and Mass concrete. (upto 10 ton) Column Up to PL level

Providing and laying controlled cement concrete M.250 and curing complete including the cost of

formwork and reinforcement for reinforced concrete work in (D) Columns, Pillars posts and struts, above

floor two level (upto 10 ton) Column Above PL level

B) Column Above PL level

Providing and laying controlled cement concrete M.250 and curing complete including the cost of

7 formwork and reinforcement for reinforced concrete work in (C) Slabs, landing, shelves, Balconies 1750.00 Cum 6511.41

Providing and laying controlled cement concrete M.250 and curing complete including the cost of

8 formwork and reinforcement for reinforced concrete work in (C) Beams, Girders and Cantilever 1400.00 Cum 6268.87

Providing and laying controlled cement concrete M.250 and curing complete including the cost of

9 formwork and reinforcement for reinforced concrete work in (E) Staircases including landing above GL 300.00 Cum 7677.51

Providing TMT Bar FE 500/500D reinforcement for R.C.C. work including bending, binding and placing in

position complete upto floor two level (upto 10 ton)

Filling availabale excavated earth (including rock) in trenches plinth, sides of foundations etc. in layers

11 not exceeding 20 cm in depth consolidating each deposited layer by ramming and watering. 1950.00 Cum 130.40

Filling in foundation and plinth with murrum or selected soil in layers of 20cm. thickness including

watering, ramming and consolidating etc. complete.

Brick work using common burnt clay building bricks having crushing strength not less than 35 kg./Sq.Cm.

13 in foundation and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B) Conventional (up to 10 ton) 3050.00 cum 4021.03

20 mm. thick sand faced cement plaster on wall upto height 15 metres above ground level consisting

14 of 12mm thick backing coat of c.m. 1 : 3 (1 cement : 3 sand) and 8 mm thick finishing coat of c.m. 1 : 1 4000.00 Sqm 326.11

(1 cement : 1 sand) etc. complete

(A) Extra over items 58 to 67 for providing and mixing water proofing materials in cement mortar in

15 50.00Per Bag of 50 Kg of Cement

proportion recommended by the manufacturer.

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of single or half brick walls for

16 interior plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1- 5750.00 Sqm 186.13

Providing 10mm thick cement plaster (i)Cement mortar 1:3 (1-cement:3-sand) for providing and mixing

17 water proofing materials in cement mortar in proportion recommended by the manufacturer. 4100.00 Sqm 138.72

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall

18 surface to give an even shade including thoroughly brushing the surface free from mortar dropping 9850.00 Sqm 40.60

and other foreign matter and sand papered smooth.

Wall painting (three coats) with plastic emulsion paint of approved brand and manufacture on

undecorated wall surface to give an even shade including throughly brushing the surface free from

mortar droppings and

other foreign matter and sand papered smooth.

Extra over item 57 for painting with plastic emulsion paint of approved brand on ceilings and sloping

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an required

21 shape even shade after thoroughly brushing the surface to remove all dirt, and remains of loose 4000.00 Sqm 114.54

powdered materials.etc complete

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm (Jindal

22 Section :2434, @ Wt. 0.643 Kg/mt) with colour anodized alluminium frame for ventilation with 5 mm thick 50.00 Sqm 1175.56

frosted glass as details etc complete for Ventilation

Providing and fixing 30mm thick FACTORY MADE SOLID PANEL PVC DOOR SHUTTER consisting of frame

made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles and 15mm x 15 mm for

top and bottom rails. M.S. frame shall have a coat of steel primers of approved make and

manufacture, M.S. frame shall be covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 x

50 mm forming stiles, and 5mm thick 75mm wide PVC sheets for top rail, lock rail and bottom rail on

23 either side, and 10mm (5mm x 2) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom 300.00 Sqm 1146.38

rail, Panelling of 5 stiles and rails with 30mm wide x 5mm thick PVC sheet beading on eighter side, and

joined together with solvent cement adhesive,. An additional 5mm thick PVC strip of 20mm width is to

be stculk on the interior side of the ‘c’ channel using PVC solvent cement adhesive etc. complete as

per direction of Engineer in charge, manufacture’s specification and drawing.

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in skrting risers of steps and dedo on 10mm

24 thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 4200.00 sqmt 1141.46

Providing and laying Vitrified tiles 8 to 10 mm thick , in skrting risers of steps and dedo on 10mm thick

25 cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement slurry 2550.00 sqmt 1538.85

Constructing a cooking platform 60 cm. width and 70 cm high resting on B.B.Masonry walls 23 cm.thick

26 in C.M.(1:6) with (ii) Fixing black kadappa stone 30mm thick laid on precast R.C.C. (1:2:4) slab with 200.00 Rmt 2656.06

plastering on exposed faces of wall in C.M. (1:4) etc complete.

Steel work, welded in built up sections framed work including cutting, hoisting, fixing in position and

applying a priming coat of red lead paint. (A)In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross beams. Hip and jack rafters, purlins conneted to

common rafters and the like

Providing and fixing rolling shutters of approved make made of 80 mm wide M.S. laths inter-locked

together through their entire length and jointed together at the ends by end locks mounted on specially

designed pipe shaft with bracket plates, guide channels and arragements for inside and outside

push-pull operation including the cost of hood cover and spring etc. complete.(A) Shutters having

width below 3.5 M.

Applying general insecticide pest control treatment to floors, cupboards etc including labour materials

etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075% concentration by mass) is

recommended 10.5ml chemical diluted with 5 liters of water application 0.5 litre chemical /Sqm of

surface is recommended as per I.S.

Providing and laying broken chine mosaic flooring for terrace using 12 mm to 20 mm broken

pieces of glazed tiles to be laid over cement mortar 1:3 to plain or slope and to be tempered to

30 bring mortar creme out upto surface using white cement including rounding off junctions and 2150.00 sqmt 747.29

extending them upto 15 cm along the wall,clearing with water and oxalic acid etc. as directed.

Providing and fixing window having extruded aluminum Colour anodized section frame main outer size

63.50 x 38.10 x 1.95 mm,@ Wt 1.094 Kg / Rmt, horizontal two track member size 61.85 mm x 31.75 mm x

1.20mm @ wt.of 0.695 Kg/mt, vertical member of size 61.85 mm x 31.75mm x 1.30 mm @ wt.of

Kg/mt with sliding shutters of horizontal member size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt,

vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with 5 mm thick

transparent bronze colour tinted float glass with powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details etc complete for window.

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved design

32 Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with sand in 4500.00 Sqm 683.89

proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm

length,30cm height and 15cm thick of M250 grade concret as per approved design and including

excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Supplying and planting of shade, ornamental, fruit, flowering trees, small, medium and large specimens

suitable for region, adaptable to low water, as per under noted varieties, with ht. as specified in

drawings including excavation of pit of size 0.9 m x 0.9 m x 0.9 m filling the pit with soil mixture etc. as per

specifications and as directed complete in all respect including, Sweet Soil, watering and nurturing for

month. The trees may be planted individually in rows or in cluster as per direction in drg. and all plant

material and its sizes and height/girth and crown should be shown to the landscape architect/ Project

Manager & written approval to be sought before planting.

300 mm polybag size; 3000 mm height; c/c distance as per drawing

Providing, planting and developing plants/ flower bed with under noted varieties of plants (both shade

& sun loving), including excavating the soil to a depth of 450mm of required area as per plant species,

removal of excavated earth to directed location, filling the excavated bed with approved soil mixture,

planting the approved variety plants, providing strong stack etc. as per specification and as directed

complete in all respect, including watering and nurturing the plants.

250 mm polybag size; 1500 mm height; 1.2 m c/c distance

Providing, and laying of good Garden earth and manure (composition of 50% ORGANIC MANURE +

50% LOCAL SOIL ) (AS PER SPECIFICATIONS), all of good quality, and laying in slope/ mound as per site

condition & as directed. Soil shall be provided by the contractor from an approved location. The

contractor has to insure that the soil should be fine in texture, free from stones, gravels, plant roots,

branches and any other unwanted material, if any. Transportation of soil upto the desired location/

locations at site shall be under contractor’s scope. Other required tools & tackles to be arranged by

contractor. Spreading shall be done as desired level as per the drawing given. Consider an even fill of

depth as per specification/Drawing.

Providing, and laying of good Garden earth and manure (composition of 50% ORGANIC MANURE +

50% LOCAL SOIL ) (AS PER SPECIFICATIONS), all of good quality, and laying in slope/ mound as per site

condition & as directed. Soil shall be provided by the contractor from an approved location. The

contractor has to insure that the soil should be fine in texture, free from stones, gravels, plant roots,

branches and any other unwanted material, if any. Transportation of soil upto the desired location/

locations at site shall be under contractor’s scope. Other required tools & tackles to be arranged by

contractor. Spreading shall be done as desired level as per the drawing given. Consider an even fill of

depth as per specification/Drawing.

SWEET GARDEN SOIL

Providing, and laying of good Garden earth and manure (composition of 50% ORGANIC MANURE +

50% LOCAL SOIL ) (AS PER SPECIFICATIONS), all of good quality, and laying in slope/ mound as per site

condition & as directed. Soil shall be provided by the contractor from an approved location. The

contractor has to insure that the soil should be fine in texture, free from stones, gravels, plant roots,

branches and any other unwanted material, if any. Transportation of soil upto the desired location/

locations at site shall be under contractor’s scope. Other required tools & tackles to be arranged by

contractor. Spreading shall be done as desired level as per the drawing given. Consider an even fill of

depth as per specification/Drawing.

Providing and fixing retro Reflective Engineering grade Board using C.R.C. (M.S.) Sheet 2mm, angle iron

75 x 75 x 6mm. Descaling and degreasing the board as per requirement using epoxyprimer epoxy paint

39 and carrying retro reflactive process by screen painting as directed etc. complete including 221.00 Sqm 11321.38

transporting and fixing in C.C. 1:4:8 with necessary excavation curing etc. complete as per I.R.C type

design.(A) Engineer Grade

Providing and fixing retro Reflective Hi Intensity Micro Prismatic Grade Board using 2mm Aluminum /

4mm ACP, angle iron 75 x 75 x 6mm. Descaling and degreasing the board as per requirement using

epoxy reflactive process by screen painting as directed etc. complete including transporting and fixing

in C.C. 1:2:4 with necessary excavation curing etc. complete as per I.R.C. 67-2012 design. A warranty for

7 years for the Retro reflective sheeting from original manufacturer & a certified copy of 3 year outdoor

exposure test report from third party test lab for the product offered shall be submitted by contractor.

(B)Class B Type-4(MDR/ODR) retro reflective sheeting

Supplying, erecting and commissioning of 6 passengers lift having following specifications

1) Size of lift well:- 1500 mm X 1650 mm ; Depth of the lift pit:- 1800mm

2) Type of lift:- 6 passenger elevator of 408 kg. capacity, suitable for G + 2 floors ,G = 3.0 m, 1 = 3.0m &

2 = 3.0m) & Total drive will be 15.0 m

3) Type of Drive system:- Variable Voltage variable Frequency Controlled

4) Rated speed:- 1.0 meter / sec .

5) Type of controller:- Full Collective Control- Simplex.

6) Car:- As per IS: 14665 - Part I / V minimum 950mm x 1200 mm x 2200mm or best fit as per shaft size

with MS Girders, bracings of adequate size and Strength at the bottom and top with angle iron frame

and all sides panels of stainless steel sheet of 1.5 mm Matt - hairline finish with safety factor more than

with PVC antiskid flooring & standard ceiling in SS hairline finish. SS Handrail in all three sides.

7) Signals:- Hail position indicator in car and Car position indicator at all landing with up / down

direction indicators with call registration facility.

8) Car & landing doors:- As per IS code clear opening 800 mm wide x 2100mm high; with automatic

Telescopic side opening doors made from stainless steel (1.5 mm)-Hairline finish @ G.F. and Powder

Coated @ Remaining Floors.

9) Car & Landing operating panel face plate in SS hairline finish and digital LED display.

10) Emergency light with 30 minutes back up & alarm bell.

11) Pre-announcing arrows for collective controls & position indicator.

12) False ceiling in car with LED lights; CCTV camera; concealed blower for ventilation & ventilation slits

41 at car panel bottom level. 2.00 Nos. 1010000.00

13) Screened infra red curtain protection on doors.

14) Audio and visual overload warning indicator.

15) Automatic rescue device.

16) Visual & acoustic confirmation of call.

17) Fireman control, intercom system & auto car light off system to be provided in car. BMS integration is

to be considered over RS485 modbus RTU. Lift doors should have fire rating of 2 hrs.

18) Overload by pass Complete with control panel duly wired with proper size and strength of copper

wire, control panel box of M.S. sheet, electric motor of suitable capacity, with class F insulation gearless

with machine room, driving/ traction pulley, diverter pulley if required, over speed governor,

electromagnetic brakes, suspension wire rope, "T" section adequate size guide rails for car and counter

weight, buffers and door frame etc. erected with necessary steel work, allied minor builders work such

as door frames for erecting doors and scaffolding for erecting guide rails etc. complete with testing with

obtaining all necessary permissions from Lift Inspector.

19) Civil work such as leveling of separator channel, plaster work, removing of projected steel bars and

beams etc to satisfcation of Engineer in charge

20)Fully comprenssive AMC for the period of two years from date of completion of companies

Warrantee period of one year after commissioning of lifts. (One + Two years of AMC)

21) BMS compatible feature is to be installed

Sculpture made of “Stainless Steel SS 304/316”

Designing, manufacturing and installation of Sculpture approx. 2 mt length in Movable made of

42 Stainless Steel SS304/316 mix of virgin and scrap material as per approved design by EIC/Architect. 2.00 Nos. 505000.00

Lifting, Placement & Fixing with all required civil work, welding DG set, tools, crane and scaffolding etc

at the site as per requirement directed by EIC.

Total Tender Cost in (Rs)

Contractor's Signature With Stamp Surendranagar Municiple Corporation

Bid Documents for Construction of Shopping Complex Cum Office at Surendranagar

Sr. No. Description Total Qty Unit Rate Rates in Words Amount

Providing, laying and jointing in true line and level U.P.V.C. pipe (SCH-40) line including fitting of PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent or as approved by Engineer-in-charge. Pipe shall be fixed on the

Rupees Seventy Two and

1 wall with help of clamp at every two meter c/c or shall be concealed as directed including necessary fittings etc. 240.00 Rmt. 72.65

Sixty Five Paise Only

including testing of pipe and joints and fixing the same with adhesive solvent, including cost of all materials.

Rupees Ninety One and

Eighty Four Paise Only

Rupees Ninety One and

Eighty Four Paise Only

Rupees One Hundred

4 (D) 32 MM 624.00 Rmt. 119.15 Nineteen and Fifteen Paise

Rupees One Hundred Forty

5 (E) 40 MM 225.00 Rmt. 148.12 Eight and Twelve Paise

Rupees One Hundred

6 (F) 50 MM 865.00 Rmt. 195.67 Ninety Five and Sixty Seven

Providing, laying and jointing in true line and level U.P.V.C. SWR Type B-pipe conforming to IS 13592-1992

with one end plain and other end socketed with rubbering & fitting conforming to IS : 14735-1999 of approved

make for drainage system pipe line; pipe shall be jointed with each other with rubber lubricant, pipe shall be fixed Rupees Eight Hundred

7 on wall using of PVC clamp of the size 160mm diameter x 210mm length x 196mm high at every 2000mm center 1440.00 Rmt. 836.74 Thirty Six and Seventy Four

or shall be concealed in walls as directed including necessary fittings such as bends, shoes etc. including testing of Paise Only

pipes and joints and jointed with adhesive solvent cement including cost of all materials.

Rupees Eight Hundred

8 (B) 160mm 897.50 Rmt. 831.22 Thirty One and Twenty

Providing and fixing cast iron (Spun) Nahni trap of the following nominal diameter of self cleaning design with Rupees Six Hundred

9 C.I. Screwed down or higher grating including cost of cutting and making good the walls and floors 100mm inlet 140.00 Each 614.03 Fourteen and Three Paise

and 50 mm outlet Only

Providing and fixing wsh down water closet (European type, W.C. Pan) with integral P or S trap including jointing

Rupees One Thousand

the trap with soil pipe in Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be measured and paid for

10 85.00 Each 1303.71 Three Hundred Three and

separately)(A) vitreous China Pattern :(i) in white colour

Seventy One Paise Only

(A) Vitreous China.

(A) Providing and fixing chromium plated brass half turn conceal cock of approved quality including fixing in pipe Rupees Two Hundred Fifty

11 line etc. complete. 85.00 Each 254.79 Four and Seventy Nine

(i) 20 mm dia conceal cock for shower Paise Only

(B) Providing and fixing chromium plated brass half turn flush cock of approved quality including fixing in pipe Rupees Two Hundred Sixty

12 line etc. complete. 85.00 Each 263.78 Three and Seventy Eight

(ii) 25 mm dia for w.c. pan Paise Only

Providing and fixing washbasin with single hole for pillar tap with C.I. or M.S. brackets painted white including Rupees One Thousand Four

13 sutting holes and making good the same .(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size. (i) 40.00 Each 1420.55 Hundred Twenty and Fifty

In white colour. Five Paise Only

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white including cutting holes in walls and Rupees Two Thousand Two

14 making good the same but excluding fittings. (C) Vitreous China Sink.(i) 600mm x 40.00 Each 2280.27 Hundred Eighty and Twenty

450mm x 150mm size Seven Paise Only

Rupees One Hundred

Providing and fixing screw down bib taps of following size :(A) Brass screw down bib tap polished bright

15 85.00 Each 186.83 Eighty Six and Eighty Three

Rupees Three Hundred

Providing and fixing pillar tap, capstan head, screw down high pressure with screws, shanks and back nuts.

16 170.00 Each 308.73 Eight and Seventy Three

Rupees Two Hundred

Providing and fixing C. P. brass shower rose with 15 mm or 20 mm inlet

17 85.00 Each 282.17 Eighty Two and Seventeen

(A) 100 mm. Dia.

Rupees Two Hundred Five

Providing and fixing brass screw down stop tap (angle cock)

18 340.00 Each 205.83 and Eighty Three Paise

(i) 15 mm dia. (4 taps per units)

Rupees One Hundred

19 Providing and fixing ball cock or approved quality as directed (A) Copper Metal (i) 50 mm dia. (overhead tank) 5.00 Each 189.84 Eighty Nine and Eighty

Four Paise Only

Rupees Nine Hundred Fifty

20 Providing and fixing C.I. Manhole cover 0.60m x 45m size having weight not less than 35Kg. (overhead tank) 8.00 Each 958.17 Eight and Seventeen Paise

Rupees One Hundred One

21 Providing and fixing G.I. rain water spout of 50mm dia and 30cm length 32.00 Each 101.91

and Ninety One Paise Only

Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber and water tight C.I. cover with Rupees One Thousand Two

22 frame of 300mm x 300mm size (inside) with standard weight (I) Square mouth traps (A) 100mm x 100mm size 'P' 32.00 Each 1292.20 Hundred Ninety Two and

type. Twenty Paise Only

Providing erecting and fixing double coated ISI water tank of required capacity each with all necessary fittings and Rupees Three and Ninety

connection etc. complete on terrace Five Paise Only

Total Tender Cost in (Rs)

Contractor's Signature With Stamp City Engineer

Surendranagar Municiple Corporation

Bid Documents for Construction of Shopping Complex Cum Office at Surendranagar

Sr. No. Description Total Qty Unit Rate Rates in Words Amount

Part-3 Internal Electrical

Providing & erecting Weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel

board having IP-64 protection made from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S. sheet for internal partitions with necessary supporting angles, flats including cutting, bending, drilling,

welding, riveting with internal partitions & instruction of engineer-in-charge with erection of Supplied switch

gears, BUSBARS, with suitable size of inter connecting PVC copper wire / copper-aliminium strips, rubber

grommets, rib, Bakelite control fuses for measuring instruments, earth bus & earth bolts, sufficient nos. of hinged

Rupees Seventeen Thousand

doors, handles with locking arrangement and rubber gasket complete. The Panel shall be painted with epoxy

1 18.00 Sq.mt 17584.10 Five Hundred Eighty Four

powder coating.

and Ten Paise Only

( The rates excludes the cost of switchgears , bus bars, inter connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding base beams) The panel shall be supplied with following

approved manufacturers with following size.

The standard companies switchgear shall be used and only manufactures at CPRI approved factory and shall be

certified by used after fabrication for beneficial use

With 350 mm depth ,0.8 x 0.8 mtr

DISTRIBUTION BOARD

Rupees Eight and Eight

2 Note :- Enclosure should be used of same company of MCB or MCBDP or ELCB Half / One Module Blanking 54.00 Nos 8.08

Plate of Standerd Size.

Supplying & erecting Sheet Steel powder coated Cable and termination Box to be mounted on Trip or Bottom of

Rupees Two Hundred Forty

3 the MCB Distribution Box for housing / covering Extra wires & Cables, suitable for following size of MCB DB 93.00 Nos 242.40

Two and Forty Paise Only

Providing and erecting Sheet Steel powder coated MCB distribution board - Flush / surface mounted fitted with

Rupees One Thousand

busbar, neutral link, earth bar and DIN rail, confirming to IS:13032 and BS-5486-1986 without MCB to house

4 3.00 Nos 1822.04 Eight Hundred Twenty Two

appropriate nos. of MCB's (The DBs should be used of same company of MCB to be used)

and Four Paise Only

Three Phase 6 way Single door for single phase outgoing horizontal box.

MOULDED CASE CIRCUIT BREAKERS

Approved make Four Pole moulded case circuit breaker having breaking capacity ICU of 35 K.A. at 415V, having Rupees Thirteen Thousand

5 normal current & rating up to 200A., with veriable thermal & magnetic release suitable to work on A.C. supply 50 3.00 Nos 13635.00 Six Hundred Thirty Five

cys. With all internal connections & complete erected in 16 G.M.S. Housing on angle frame. ICS= 100% of ICS Only

MINIATURE CIRCUIT BREAKERS.

Rupees One Hundred

Miniature circuit breaker Single Pole 6 A to 32 A suitable to operate on 240 V A. C. system and having overload

6 378.00 Nos 116.15 Sixteen and Fifteen Paise

and short circuit tripping elements and breaking capacity 10 KA to be erected in existing M. S. Box confirming to

IS 8828/1996 with ISI mark. Cat-III

Providing & erecting 230 V. MCB Two Pole switch for Motor & inductive Load ( C Curve) having 10 KA

Rupees Three Hundred

7 breaking capacity & confirms to IS: 8828 in existing box having following capacity 183.00 Nos 308.05

Eight and Five Paise Only

A) 6 to 32 Amp. Cat-II ( For Incomer of DB of Individual Home & Outgoing of Floor LDB)

Providing & erecting 415 V. MCB Four Pole switch for Motor & inductive Load ( C Curve) having 10 KA

Rupees Six Hundred

8 breaking capacity & confirms to IS: 8828 in existing box having following capacity 75.00 Nos 616.10

Sixteen and Ten Paise Only

A) 6 to 32 Amp. Cat-II

1. For Point wiring above 10 mtr of length, additional length will be added at rate of mains.

2. For point wiring in bathroom ,W/C and Wash basin area in residential quarters reduce overall rate by 50% of

point wiring for light.

Point wiring in Copper

Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multistrand copper wires, in existing pipe duly erected complete with earth

continuity and necessary connection with primary light with accessories erected on polished wooden block/Metal/

Rupees Four Hundred Four

9 PVC box covered with 3 mm thick laminated sheet for open / concealed wiring. 3600.00 Nos 404.00

Note:- Maximum up to 6 mtrs length, excess will be considered as Mains for Secondary Point.

Point wiring in Copper (Modular)

Point wiring for Light / Bell with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multistrand copper wires, in existing pipe duly erected complete with 6A Modular type

switch / bell push & accessories and earth continuity of following type, erected on PVC / Metallic box covered

with appropriate front plate modules erected on / in wall / ceiling as per pipe erected

(a) with medium class Rigid PVC pipe and accessories Cat-II

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multistrand copper wires, in existing pipe duly erected complete with 6A Modular type

Rupees Five Hundred

switch and hum free EME four or more step type electronic fan regulator with separately mounted and accessories

10 270.00 Nos 585.80 Eighty Five and Eighty

with earth continuity of following type erected on PVC / Metallic box covered with appropriate front plate modules

erected on / in wall / ceiling as per pipe erected.

(a) with medium class Rigid PVC pipe and accessories Cat-II

Point wiring for Individual Plug with & earthwire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multistrand copper wires, in existing pipe duly erected complete with Modular type switch &

Rupees Seven Hundred

5 pin Plug erected on PVC / Metallic box covered with appropriate front plate modules erected on / in wall /

11 5400.00 Nos 737.30 Thirty Seven and Thirty

ceiling as per pipe erected with following type of accessories.-CAT II

[I] For 6A Plug with 2-1.5 sq.mm Cu. Wire

(a) with medium class Rigid PVC pipe and accessories Cat-II

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC / Metallic box covered Rupees Two Hundred

12 with appropriate front plate modules erected on / in wall / ceiling with following type accssories 720.00 Nss 222.20 Twenty Two and Twenty

B) Single mounting

Providing followingbase-frame & Textured

type of Modular Type /Accessories

Metallic front plates. withCat-II

mounted pvc / metallic box covered with appropriate Paise Only

front plate modules erected with necessary connection. As desired by Engineer Incharge

Rupees One Hundred Thirty

13 (3) Two Pin / RJ-11 Telephone Socket with Top Cat-II 720.00 Nos 131.30

One and Thirty Paise Only

[A] For One Gang

Rupees One Hundred Forty

14 (4) TV Co-axial Socket outlet Cat-II 630.00 Nos 141.40

One and Forty Paise Only

Rupees One Hundred

15 (11) Bell Push Cat-II 630.00 Nos 111.10

Eleven and Ten Paise Only

Conduits & Pipes

Providing and erecting 1.5 mm thick FIA approved and ISI mark ( embossed) RIGID PVC PIPES of following size

complete erected with necessary PVC fittings and Junction boxes fixed with adhesive solution and Clamps with

Rupees Thirty Two and

16 following type of erection. 4500.00 Mtr 32.32

Thirty Two Paise Only

(2) For erection concealed in wall / slab along with continuous fish wire to draw mains, laid in approved manner

with Plastering by cement mortar & finishing the surface to match the wall / ceiling.

Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts

Rupees Twenty Five and

17 etc. complete of following sizes. 3600.00 Mtr 25.25

Twenty Five Paise Only

Supplying & erecting PVC trunking (PVC Casing-n-Caping) having double-locking arrangement with grooves,

trunking of size not below 12.5 mm in height as per IS with accessories of PVC/Resin polypropylene not below 1.8 Rupees Thirty and Thirty

mm thick duly sealed in joint & erected on wall / ceiling of following size . Paise Only

Rupees Thirty Five and

Thirty Five Paise Only

Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated Rupees Sixty and Sixty

stranded wire of green colour for earth continuity of following size Paise Only

(a) with medium class Rigid PVC pipe and accessories

(a) 2 wire 1.5 sq. mm

Rupees Eighty and Eighty

Rupees Thirty and Thirty

22 (a) 1 wire 1.5 sq. mm for Earthing ( Qty as per above ) 6300.00 Mtr 30.30

Rupees One Hundred Forty

23 Approved Make CFL Non-Retrofit Light 13/15/18 watt erected if required cat ll 270.00 Nos 141.40

One and Forty Paise Only

Approved Make Energy Meter 230 V,50 c/s, AC Up to 20A erected as directed with three year replacement

24 guarantee 42.00 Nos 1060.50

TELEPHONE WIRING

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable

for telephone wiring & confirming to C-DOT erected in existing pipe.of following size of conductors & nos.of

pairs. With necessary connections. Conductor Size 0.5 mm

Providing and erecting Sheet Steel powder coated MCB distribution board - Flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, confirming to IS:13032 and BS-5486-1986 without MCB to house

appropriate No.s. of MCB's (The DBs should be used of same company of MCB to be used) Three Phase 4 way

Single door for single phase outgoing horizontal box.

MINIATURE CIRCUIT BREAKERS.

Providing & erecting 415 V. MCB Four Pole switch for Motor & inductive Load ( C Curve) having 10 KA

breaking capacity & confirms to IS: 8828 in existing box having following capacity

A) 6 to 32 Amp. Cat-II

Approved make energy meter 3 phase 4 wire unbalanced load 500 V,10 A to 60 A complete erected as directed

28 with necessary earth wire, 3.00 Nos 3120.90

UNARMOURED COPPER CABLES.

Supplying and erecting XLPE(IS:7098)(I)-88 ISI marked unarmoured Copper cable for 1.1 KV grade to be erected

29 as directed of following size. 900.00 Mtr. 199.98

F) 3 Core 4 Sq.mm.

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile,

Front Cover : High Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power

tolerance Pmax: 0/+5, Module Efficiency should be approx. 19.5%-22%, Normal operating temperature 45'C,

Junction Box with Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules, Thep. temp. co-efficient of the PV module shall equal or

better than -0.45%/degree C. Solar PV modules of minimum fill factor 75% to be used. Unit Production:- More

than 4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year Product warranty and 25 year Linear Power Warranty

includes all mechanical and electrical parameters of the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is 5:6 for the Installation capacity which are given

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency: 97.5% - 98.9%, O/p Frequency:

50/60Hz, Operating Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -

25~60°C, Integrated protection of Inverter are Anti-islanding Protection, Input Reverse Polarity Protection,

Insulation Resistor Detection, Ground fault protection, Residual Current Monitoring Unit, Output Over Current

Protection, Output Short Circuit Protection, Output Over Voltage Protection, PV array string fault Protection.

Protection Degree: IP65, User Interface LCD & APP, Datalogger & Communication: GPRS / Wi-Fi.

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual Current

Monitoring Unit Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection Integrated,

Output Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD & APP,Datalogger &

Communication: GPRS / Wi-Fi, Module Mounting Structure: The mounting (Rectangular pipe / square pipe /

circular pipe) with requisite cross bars, nuts and bolts, etc. shall be Hot deep galvanized with minimum 80micron

coating. The Rectangular / square /circular hollow pipe section used for the structure should have a minimum

thickness of 2.0 mm. other than above, the material thickness should be minimum 2.5 mm. A certificate of a

structural engineer certifying the strength and stability of the mounting structure to withstand the weight and wind

speed of 150 km/hour throughout the life span of 25 years of the system, shall be submitted by the vendors. Hot

Dipped Galvanized steel coils. suitable arrangement for base plate for foundation , solar panel mounting, the

structure should be suitable for carry the load of solar panel,wiring, sprinkler system etc. with necessary foundation

work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be (SS 304)

quality.The ground clearance of the bottom most edge of solar panel shall not be less than 300 mm to 1200 mm or

as per site’s technical/feasibility requirement.

a. Column –The minimum section (thickness) should be 60MM*40MM

b. Rafter - The minimum section (thickness) should be 60MM*40MM

c. Purlin - The minimum section (thickness) should be 40MM * 40MM Balane of System with necessary

Swichgears (Suitabel size and protection of ACDB & DCDB), inter connecting wiring, earthing system as per the

CEIG drawing approval, lightining arrester system as per the CEIG drawing approval, all liasoning work with

various gov. dipartment like state nodal agency,DISCOM & CEIG is included in agency scope

(D) Grid Tied Solar Power System: 26 - 50 kW (3 - phase)

Total Tender Cost in (Rs)

Contractor's Signature With Stamp City Engineer

Surendranagar Municiple Corporation

Bid Documents for Construction of Shopping Complex Cum Office at Surendranagar

Sr. No. Description Total Qty Unit Rate Rates in Words Amount

Supplying, Installation, Testing and commissioning of electric driven main fire pump suitable for automatic

operation and consisting of following: Horizontal type, centrifugal End Suction pump of cast iron body & bronze

Rupees Three Hundred Ten

impeller , mechanical seal to ensure a minimum pressure of 3.5 kg / sq.cm. at highest and farthest outlet at

1 1.00 Nos. 310500.00 Thousand Five Hundred

specified flow of 137m3/Hour@70Mtr. head conforming to IS 1520. The pump shall be coupled to TEFC motor

of suitable HP & speed and complete set shall mounted on common base frame with, coupling, coupling guard,

foundation bolts etc. as required.

Supplying, Installation, Testing and commissioning of Diesel engine driven fire pump suitable for automatic

operation and consisting of following: Horizontal type, centrifugal End Suction pump of cast iron body & bronze Rupees Six Hundred Sixty

2 impeller , mechanical seal to ensure a minimum pressure of 3.5 kg / sq.cm. at highest and farthest outlet at 1.00 Nos. 660840.00 Thousand Eight Hundred

specified flow of 137m3/Hour@ 70M. head conforming to IS 1520. with M.S.fabricated common base plate, Forty Only

coupling, coupling guard, foundation bolts etc. as required

Supplying, Installation, Testing and commissioning of Electric Driven Jockey Fire pump suitable for automatic Rupees One Hundred

3 operation and consisting of following: Horizontal type, centrifugal End Suction pump of cast iron body & bronze 1.00 Nos. 119800.00 Nineteen Thousand Eight

impeller and dynamically balanced ,SS shaft mechanical seal and specified flow of 10.8m3/Hour@70M head. Hundred Only

Fabricating & Supply, installing, testing and commissioning of sheet steel clad floor mounting Fire Pump control

panel having suitable size for control of 1 no. main for Hydrant, 1 no standby fire Diesel Pump, 1 no. jockey

Rupees Two Hundred

pumps having suitable incoming MCCB, incoming voltmeter with selector switch and fuses. Auto-DOLstarters

4 1.00 No. 200800.00 Thousand Eight Hundred

with hand reset overload cum single phase preventor type relay, OFF/AUTO/MANUAL selector switches,

Ammeters to read current in all 3 phases with selector switch, alarm with reset push button which will

automatically reset for the next cycle.

Supplying, laying, testing & commissioning of XLPE, PVC outer sheathe, steel armoured, copper conductor,

5 1100v grade power cables with glands etc.The cables shall be laid in tray. as required..The size of the cables shall Rupees Only

as mentioned below,

6 3.5 C X 35 Sqmm Aluminium Armoured Cable 75.00 Mtr 200.00 Rupees Two Hundred Only

7 3 C X 6 Sqmm Aluminium Armoured Cable 45.00 Mtr 25.00 Rupees Twenty Five Only

8 2 C X 1.5 Sqmm Aluminium Armoured Cable 225.00 Mtr 45.00 Rupees Forty Five Only

Supplying & laying, Ladder Type Hot dip G.I. cable tray of 14G of specific dimensions. The cable tray shall be

9 hung from ceiling / fixed to wall with necessary ceiling suspensors, tee, nots, nuts etc, together with tees, bends etc Rupees Only

including cost for necessary supports as required.

Rupees Four Hundred

10 Cable Tray 300X50 mm. 25.00 Mtr 480.00

Rupees Two Hundred Ten

11 Cable Tray 150X50 mm. 25.00 Mtr 210.00

Supplying & laying of G.I. Earthing strips of 50mm x 6mm thick, strip shall be run on floor / ceiling / walls, from

12 the equipment to the nearest Earth pit with neccessory accessories as required. ( Earth pit shall be executed by 75.00 Mtr 60.00 Rupees Sixty Only

other agencies).

Providing, fixing, testing & commissioning of Glicerin Filled 150mm dia dial type Pressure Gauge and range of 0- Rupees One Thousand Six

15 Kg/cm2. Hundred Only

Rupees One Thousand

14 Providing, fixing, testing and commissioning of Pressure switches. 5.00 Nos. 1700.00

Seven Hundred Only

Supply, installation, testing and commissioning of C.I.Butterfly valve PN16 conforming to IS:13095/BS :5155

with Flanges,GI Nut bolts, Gaskets completed as required.

16 200mm dia (Lever operated) 25.00 Nos. 10000.00 Rupees Ten Thousand Only

Rupees Five Thousand Five

17 150mm dia. (Lever operated) 25.00 Nos. 5500.00

Rupees Four Thousand

18 100mm dia. (Lever operated) 75.00 Nos. 4000.00

Rupees Three Thousand

19 80mm dia. (Lever operated) 6.00 Nos. 3000.00

Rupees Two Thousand Five

20 50mm dia. (Lever operated) 5.00 Nos. 2500.00

21 Supplying, installing, testing and commissioning of Forged Brass Ball valves with fittings of screwed end type. Rupees Only

22 25mm dia 6.00 Nos. 10000.00 Rupees Ten Thousand Only

23 15mm dia 10.00 Nos. 600.00 Rupees Six Hundred Only

Providing, fixing, testing and commissioning of C.I. Dual plate type Non-Return Valve class PN 16 rating with

fittings, flanges, nutbolts, washers, gaskets etc.of sizes:

Rupees Eight Thousand

Rupees Four Thousand

Supplying, Installation, Testing and commissioning of Above Ground G.I Black C Class Heavy duty pipes as per

IS: 1239 (upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting, screwing, welding

etc. and providing all fittings like flanges, bends,elbows, reducers, clamps, hangers etc. with painting of one coat

of primer and 2 or more coats of synthetic enamel paint of approved make / shade complete as per specification.

Rupees Three Thousand

28 200mm dia 27.00 Meter 3300.00

Three Hundred Only

Rupees Three Thousand

29 150mm dia 27.00 Meter 3000.00

Rupees Two Thousand

30 100mm dia 18.00 Meter 2000.00

Rupees One Thousand

31 80mm dia. 9.00 Meter 1000.00

32 25mm dia 9.00 Meter 400.00 Rupees Four Hundred Only

33 Providing and fixing, testing and commissioning of Y Type Strainer. Rupees Only

Rupees Thirty Two

Rupees Seven Thousand

Five Hundred Only

Supplying, Installation, Testing and commissioning of Above Ground G.I Black C Class Heavy duty pipes as per

IS: 1239 (upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting, screwing, welding

etc. and providing all fittings like flanges, bends,elbows, reducers, clamps, hangers etc. with painting of one coat

of primer and 2 or more coats of synthetic enamel paint of approved make / shade complete as per specification.

Rupees Three Thousand

37 150mm dia. 0.00 Meter 3300.00

Three Hundred Only

Rupees Two Thousand One

38 100mm dia. 0.00 Meter 2100.00

Rupees One Thousand Five

39 80mm dia. 18.00 Meter 1500.00

Supplying, Installation, Testing and commissioning of Under Ground G.I Black C Class Heavyduty pipes as per

IS: 1239 (upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) with IWL/pypecoat, 4mm thickness

wrapping and coating and providing all fittings like flanges, elbow,reducer with all required.(The rates area

exclusive of Excavation & Back Filling)

Rupees Three Thousand

Five Hundred Only

Rupees Two Thousand Five

42 100mm dia. 9.00 Meter 2500.00

Rupees Two Thousand

43 80mm dia. 108.00 Meter 2000.00

Supply, installation, testing and commissioning of C.I.Butterfly valve PN16 conforming to IS:13095/BS :5155

with Flanges,GI Nut bolts, Gaskets completed as required.

Rupees Five Thousand

Three Hundred Only

46 Supplying, installing, testing and commissioning of Forged Brass Ball valves with fittings of screwed end type. Rupees Only

Rupees One Thousand

47 25mm dia (Drain pipe ) 2.00 Nos. 1000.00

Supplying, Installation, Testing and commissioning of SS Single Headed Oblique Pattern Hydrant Landing Rupees Five Thousand

Valves as per IS: 5290 with 80 mm dia flanged inlet & 63 mm dia female outlet complete with cap and chain etc. Three Hundred Only

Supplying, Installation, Testing and commissioning of SS Branch Pipe with nozzle of 20 mm nominal bore outlet Rupees One Thousand

suitable to fit with standard instanteneous type 63 mm dia coupling. As per IS:903. Three Hundred Only

Supplying, Installation, Testing and commissioning of 63 mm dia 15m long RRL Hose Pipe with 63 mm dia.Type

Rupees Four Thousand

50 A Male and female Stainless Steel couplings duly binded with GI wire, rivets etc. conforming to IS 636 as 39.00 Nos. 4200.00

Two Hundred Only

Supplying, Installation, Testing and commissioning of weather proof Fire Hose cabinet size 600x 750x250mm

to house fire hydrant & hose, including all other related accessories fabricated from M.S. sheet (16 Gauge) Rupees Two Thousand

of fully welded construction having front door with locking arrangement, partially glazed with 4 mm thick glass. Three Hundred Only

Cabinet shall be powder coated & painted with post office red colour

Supplying, Installation, Testing and commissioning of Wall mounting swing type First aid Fire Hose Reel with

Rupees Six Thousand Three

52 drum, hanging bracket,30 M x 25 mm dia high pressure hose reel tubing as per IS:884 with shut nozzle and ball 39.00 Nos. 6300.00

valve and all required accessories.

Supplying, Installation, Testing and commissioning of 25 mm dia Air Release Valve and Ball Valve assembly on Rupees Eighteen Thousand

top of each riser for Air release system. Only

Supplying, Installation, Testing and commissioning of CI Four way Fire Brigade Inlet as per IS: 904 having 63 Rupees Seven Thousand

mm dia inlet with 150 mm dia Butterfly valve blank cap and chain with necessary fittings, flanges, nutbolts etc. Four Hundred Only

Supplying, Installation, Testing and commissioning of CI Two way Fire Brigade Inlet as per IS: 904 having

Rupees Four Thousand

55 mm dia inlet with blank cap and chain with 100 mm dia Butterfly valve necessary fittings, flanges, nutbolts, 2.00 Nos. 4200.00

Two Hundred Only

gasket and all required accessories.

Providing & fixing of 6 Kg Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type,

Rupees Two Thousand Five

56 Pressure Gauge, Controllable discharge mechanism Class A Rating 3A & Class B rating 21B as per IS 15683 ISI 27.00 Nos. 2500.00

MARK (ABC Dry Chemical Powder - MAP 50%).

Providing & fixing of CO2 type Fire Extinguisher of capacity 4.5 kg filled with Co2 Gas as per IS 15222 with

Rupees Five Thousand Two

57 controll discharge mechanis, fitted with Hose & Horn applicable on Class B fire rating 21B confirms to IS 15683 27.00 Nos. 5200.00

bearing ISI mark. Co2 cylinder as per IS7285

Providing and fixing of 6Kg K- type, Kitchen fire extinguishers as per ISI Marked complete with first filling and

all standard accessories etc as required. Operating temp -20 degree C to + 45 degree C, Min jet length 2 to 4 Mtr, Rupees Fourteen Thousand

Discharge percentage 90%, Discharge time 45 to 55 sec., Charge pressure 15 kg/ cm2, Test pressure- 35 kg/ cm2, Only

Extinguisher media- Potassium Acetate, Cylinder material - SS.

Supplying, Installation, Testing and commissioning of Above Ground G.I Black C Class Heavy duty pipes as per

IS: 1239 (upto 150 mm dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting, screwing, welding

etc. and providing all fittings like flanges, bends,elbows, reducers, clamps, hangers etc. with painting of one coat

of primer and 2 or more coats of synthetic enamel paint of approved make / shade complete as per specification.

Rupees One Thousand

60 80mm dia. 18.00 Meter 1300.00

Three Hundred Only

Rupees One Thousand

61 65mm dia. 9.00 Meter 1300.00

Three Hundred Only

Rupees Eight Hundred

62 50mm dia. 9.00 Meter 800.00

Rupees Seven Hundred

63 40mm dia. 18.00 Meter 700.00

Rupees Four Hundred Fifty

64 25mm dia 81.00 Meter 450.00

Providing and fixing, testing and commissioning of K 5.6 Pendent type Standard Response Sprinkler rating of 68 Rupees Three Hundred

deg.C. with required accessories. Only

Supplying, Installation, Testing and commissioning of SS Flexible drops 1200mm Long.Unbraided , Maximumm

Service pressure 175PSI,.Sprinkler Flexible Drop system is a ready to use assembly to fit sprinkler heads in Rupees One Thousand Two

desired location in a suspended ceiling. It easily positions the sprinkler in center of the ceiling tile at a correct Hundred Only

Supply, installation, testing and commissioning of C.I.Butterfly valve PN16 conforming to IS:13095/BS :5155

with Flanges,GI Nut bolts, Gaskets completed as required.

Rupees Three Thousand

Three Hundred Only

69 Total of Sprinkler System. Rupees Only

70 Signages, Steel Structure and NOC Rupees Only

Rupees One Hundred Sixty

71 Providing, fixing, testing and commissioning of below Auto Glow Signages. Exit .4” X 12” 25.00 Nos. 165.00

Rupees One Hundred Sixty

72 Providing, fixing, testing and commissioning of below Auto Glow Signages. " Fire Extinguishers" 4"x 12" 27.00 Nos. 165.00

Rupees One Hundred

73 Supply, Installaton of Structure Steel Support. 1225.00 Mtr. 190.00

Total Tender Cost in (Rs)

Contractor's Signature With Stamp City Engineer

Surendranagar Municiple Corporation