Construction of New Boys Hostel Building (100 Cap.) at ITI Tarsali, Vadodara

Name of Work :- Construction of New Boys Hostel Building (100 Cap.) at ITI Tarsali,

BILL OF QUANTITIES

(A)Percentage Rate Tender (Up to INR 50 Cr. )

Item Description of Item Qty. Unit Rate In Amount in Rupees

1 Excavation for foundation up to 1.50mt. Depth including 2341.00 CuM 120.01

sorting out and stacking of useful materials and disposing of

the excavated stuff all lead and lift. (A) loose or soft Soil

2 Excavation for foundation for depth from 1.5 m to 3.0 m 1884.00 CuM 166.44

including sorting out and stacking of useful materials and

disposing off the excavated stuff all lead and lift.(B)

Dense or Hard soil

3 Excavation for foundation for depth from 3.0 m to 5.0 m 1570.00 CuM 180.38

including sorting out and stacking of useful materials and

disposing off the excavated stuff up to All lead and lift

. (B) Dense or Hard soil

4 Excavation for foundation upto 1.50mt. Depth including 446.00 CuM 208.93

sorting out and stacking of useful materials and disposing off

the excavated stuff all lead and lift (A) loose or soft soil

5 Excavation for foundation for depth from 1.50m to 3.00m 372.00 CuM 289.92

including sorting out and stacking of useful materials and

disposing off the excavated stuff all lead and lift. (B) Dense

6 Excavation for foundation for depth from 3.00m to 5.00m 372.00 CuM 311.56

including sorting out and stacking of useful materials and

disposing off the excavated stuff all lead and lift (B) Dense

7 Excavation for foundation upto 1.50mt. Depth including 149.00 CuM 153.41

sorting out and stacking of useful materials and disposing of

the excavated stuff all lead and lift (B) Dense or Hard soil

8 Excavation for foundation upto 1.50mt. Depth including 97.00 CuM 262.52

sorting out and stacking of useful materials and disposing of

the excavated stuff all lead and lift (B) hard Murrum

9 Filling in plinth with sand under floors including 296.00 CuM 471.69

watering ramming, consolidating and dressing complete

10 Providing and laying cement concrete 1:4:8 (1- Cement : 4- 335.00 CuM 2747.21

coarse sand : 8- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

11 Providing and laying controlled cement concrete M 250 948.00 CuM 4434.91

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in. (A) Foundation footing, base of columns & mass

12 Providing and laying controlled cement concrete M 250 56.00 CuM 7758.82

using B.T. stone aggregate and curing complete including

the cost of form work but excluding the cost of reinforcement

for reinforced concrete work in. Columns up to plinth

Item Description of Item Qty. Unit Rate In Amount in Rupees

13 Providing and laying cement concrete 1:3:6 (1- Cement : 3- 327.00 CuM 3080.90

Coarse sand : 6- Graded brick bat aggregate 40mm normal

size) and curing complete excluding cost of formwork in (A)

Foundation and Plinth

14 Providing and Laying controlled cement concrete M-250 & 129.00 CuM 6211.50

curing complete including the cost of form work but

excluding cost of reinforcement concrete work in Beams,

Girders and Cantilever up to floor for PLINTH BEAMS

15 Brick work using common Brunt clay building bricks having 210.00 CuM 4121.55

crushing strength not less than 35 Kg./Sq.cm.. In

foundation and plinth in cement mortar 1:6 (1cement :

fine sand) (b) Conventional

16 Filling in foundation and plinth with murrum or selected 3347.00 CuM 296.29

soil in layers of 20cm. thickness including watering, ramming

and consolidating etc. complete.

17 Applying general insecticide pest control treatment to 1068.00 SqM 51.85

floors, cupboards etc. including labour materials etc.

complete. Using Imidacloprid 30.5 SCas Per IS 6313 part -

II( (0.075% concentration by mass) is recommended 10.5ml

chemical diluted with 5 liters of water application 0.5 liter

chemical /SqM of surface is recommended as per I.S.

18 Providing and Laying controlled cement concrete M-150 143.00 CuM 5175.24

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

19 Providing and Laying controlled cement concrete M-200 44.00 CuM 7693.17

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Column having any cross section area of

Column. For Ground Floor Column.

20 Providing and Laying controlled cement concrete M-200 43.00 CuM 7693.17

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Column having any cross section area of

Column. For First Floor Column.

21 Providing and Laying controlled cement concrete M-200 43.00 CuM 7733.12

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Column having any cross section area of

Column. For Second Floor Column.

22 Providing and Laying controlled cement concrete M-200 16.00 CuM 7773.06

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Column having any cross section area of

Column. For Third Floor Column.

23 Providing and Laying controlled cement concrete M-200 102.00 CuM 6703.37

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in beam having any cross section area of BEAM. for

24 Providing and Laying controlled cement concrete M-200 102.00 CuM 6703.37

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in beam having any cross section area of BEAM. for

Item Description of Item Qty. Unit Rate In Amount in Rupees

25 Providing and Laying controlled cement concrete M-200 102.00 CuM 6743.32

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in beam having any cross section area of BEAM. for

26 Providing and Laying controlled cement concrete M-200 3.00 CuM 6783.26

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in beam having any cross section area of BEAM. for

27 Providing and Laying controlled cement concrete M-200 13.00 CuM 7566.92

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Lintel. For Ground Floor

28 Providing and Laying controlled cement concrete M-200 13.00 CuM 7566.92

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Lintel. For First Floor

29 Providing and Laying controlled cement concrete M-200 13.00 CuM 7606.87

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Lintel. For Second Floor

30 Providing and Laying controlled cement concrete M-200 1.00 CuM 7646.81

and with curing etc. Complete. Including the cost of

formwork but excluding the cost of reinforcement for R.C.C

work in Lintel. For Third Floor

31 Providing and Laying controlled cement concrete M-200 26.00 CuM 6972.49

for reinforced concrete chhajja not exceeding 10cm

thickness up to floor two level including finishing the

exposed surface with cement mortar 1:3 ( 1 cement : 3 fine

sand) to give a smooth surface ,centering and formwork and

curing complete. excluding cost of reinforcement FOR RCC

CHHAJJA ALL Floor.

32 Providing and Laying controlled cement concrete M-200 27.00 CuM 9469.21

and curing etc. comp including the cost of formwork but

excluding the cost of reinforcement for Vertical Fins All

33 Providing and Laying controlled cement concrete M-200 132.00 CuM 7243.72

Finishing smooth with curing etc. comp including the cost of

formwork but excluding the cost of reinforcement for RCC

work in SLAB for Ground Floor

34 Providing and Laying controlled cement concrete M-200 129.00 CuM 7243.72

Finishing smooth with curing etc. comp including the cost of

formwork but excluding the cost of reinforcement for RCC

work in SLAB for First Floor

35 Providing and Laying controlled cement concrete M-200 129.00 CuM 7283.67

Finishing smooth with curing etc. comp including the cost of

formwork but excluding the cost of reinforcement for RCC

work in SLAB for Second Floor

36 Providing and Laying controlled cement concrete M-200 5.00 CuM 7323.61

Finishing smooth with curing etc. comp including the cost of

formwork but excluding the cost of reinforcement for RCC

work in SLAB for Third Floor

37 Providing and laying controlled cement concrete M-200 15.00 CuM 6803.02

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced concrete

work in STAIRCASES FOR ALL FLOOR

Item Description of Item Qty. Unit Rate In Amount in Rupees

38 Providing ISI Mark T.M.T. bar Fe - 500D reinforcement 234345.00 Kg 77.53

for R.C.C work including bending, binding and placing

in position complete up to floor two level For All Floor

39 Brick work using common burnt clay building conventional 534.00 CuM 4403.40

type bricks having crushing strength not less than

Kg./Sqcm. in super structure in cement mortar 1:6 (1

cement : 5 fine sand) for Ground floor,FF including the

cost of all materials and labour charges etc.

complete.(A)Conventional

40 Brick work using common burnt clay building conventional 235.00 CuM 4444.90

type bricks having crushing strength not less than

Kg./Sqcm. in super structure in cement mortar 1:6 (1

cement : 5 fine sand) for Second floor including the cost of

all materials and labour charges etc.

complete.(A)Conventional

41 Brick work using common burnt clay building conventional 66.00 CuM 4486.40

type bricks having crushing strength not less than

Kg./Sqcm. in super structure in cement mortar 1:6 (1

cement : 6 fine sand) for Third floor including the cost of all

materials and labour charges etc. complete. (A)Conventional

42 Half brick masonry in common brunt clay building bricks 496.00 SqM 669.50

having crushing strength not less than 35 Kg./Sq.cm.. In

cement mortar 1:4 (1cement : 3 coarse sand) in super

structure above plinth level For GROUND

FLOOR,FF(A)Conventional

43 Half brick masonry in common brunt clay building bricks 263.00 SqM 675.56

having crushing strength not less than 35 Kg./Sq.cm.. In

cement mortar 1:4 (1cement : 3 coarse sand) in super

structure above plinth level For SF & Third FLOOR

(A)Conventional

44 Providing 20mm thick cement plaster in double coat on 7008.00 SqM 267.90

single or half brick walls for interior plastering up to floor two

level and finished even and smooth in (i) Cement mortar 1:4

(1-cement:4-sand) For Ground Floor,FF

45 Providing 20mm thick cement plaster in double coat on 3648.00 SqM 291.88

single or half brick walls for interior plastering up to floor two

level and finished even and smooth in (i) Cement mortar 1:4

(1-cement:4-sand) For SF

46 Providing 20mm thick cement plaster in single coat on 537.00 SqM 266.45

single or half brick walls for interior plastering up to floor two

level and finished even and smooth in (i) Cement mortar 1:4

(1-cement:4-sand) For Third Floor

47 Providing 10 mm thick cement plaster in single coat on 2957.00 SqM 154.57

fair side brick/concrete walls for interior plastering up to floor

two level and finished even and smooth in cement mortar

1:4 (1 cement : 4 sand) including finishing with a floating

coat of neat cement slurry etc. complete for Ceiling For

Ground Floor,FF,SF,Terrace

48 Providing 20 mm thick waterproof cement plaster of 440.00 SqM 324.94

sunk in single coat on brick/concrete walls for interior

plastering finished even and smooth in cement mortar 1:3 (1

cement : 3 sand) and mixing water proofing materials of

approved brand and manufacture in C.M. in proportion

recommended by the manufacture and finished with a

floating coat of neat cement slurry for all floor.

Item Description of Item Qty. Unit Rate In Amount in Rupees

49 20mm thick sand faced cement plaster on all heights of 2131.00 SqM 337.52

walls above ground level consisting of 12mm thick backing

coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete

For all heights

50 Providing throating or Plaster drip and moulding to RCC 600.00 Rmt 42.70

51 Providing 12mm wide groove/notch in plaster including 1892.00 Rmt 22.22

finishing the same etc. Complete for all height.

52 Providing & fixing Door having 18mm thick Granite Frame 160.00 SqM 6168.07

and having pivoted Double shutters of factory made and

35 mm thick solid core finished with 1mm thick Lamination

on both side and 12mm TH T.W. Edge beading with S.S.

handle and other S.S. Fixture & fastenings as directed by

Architect etc. complete

53 Providing & fixing Door having 18mm thick Granite Frame 38.00 SqM 7256.85

and having pivoted Single shutter of factory made and

mm thick solid core finished with 1mm thick Lamination on

both side and 12mm TH T.W. Edge beading with S.S.

handle and other S.S. Fixture & fastenings as directed by

Architect etc. complete

54 Providing and fixing FRP frame size 125x65 mm and 48.00 SqM 2615.04

35mm thick FRP depress panel shutter having extra

reinforcement on sides & edges in Gel coat finish. The core

of the shutter & frame is to be filed up with injected fire

retardant grade polyurethane foam done in situ along with

embedded wooden pieces for stiffening & also taking hinges

& fixtures. The whole FRP frame & shutter is to be water

proof weather proof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & aluminum fixtures & fastenings &

fastener sleeve.

55 Providing and fixing standard extruded Colour anodised 20.00 SqM 7234.63

Aluminum Section window Three shutter sliding

window (Three shutters And One shutter For Mosquito net )

section equivalent to Jindal E Series (30mm) sections

numbered, Shutter top and bottom -20993 0.839 kg/Rmt

shutter inter lock -20550, 0.994 shutter side (handle) -

20549 ,0.809 kg/Rmt Frame bottom with weep holes-20928

, 2.032 Kg/Rmt, Frame top and Side 20837 1.197 kg/Rmt

using three Shutter with 5 mm thick transparent bronze

colour tinted float glass and One Shutter with Stainless Steel

Mosquito Wires mesh (jali) Shutter EPDM rubber gasket, air

lock streep,And Finishing Joint with Silicon Sealant, with

powder coated standard Colour Anodized aluminum coated

Fitting and Fixture & Fastening Etc Complete , Colour

(except black) As Directed by Engineer in Charge and

Aluminum Section Shall As Per Is Standard.

Item Description of Item Qty. Unit Rate In Amount in Rupees

56 Providing and fixing standard extruded Colour anodised 220.00 SqM 9119.29

Aluminum Section window Two shutters sliding

window (Two shutters Window And One shutter For

Mosquito net ) section equivalent to Jindal E Series (30mm)

sections numbered, Shutter top and bottom -20993

kg/Rmt shutter Inter Lock-20550 0.994 kg/Rmt, shutter side

(handle)- 20549 ,0.809 kg/Rmt Frame bottom with gutter &

weep holes 20928, 2.032 kg/Rmt Frame top and Bottom

20837, 1.197 kg/Rmt using three Shutter with 5 mm thick

transparent bronze colour tinted float glass and One Shutter

with Stainless Steel Mosquito Wire mesh (jali) Shutter

EPDM rubber gasket, air lock streep,And Finishing Joint with

Silicon Sealant, with powder coated standard Colour

Anodized aluminum coated Fitting and Fixture & Fastening

Etc Complete , Colour (except black) As Directed by

Engineer in Charge and Aluminum Section Shall As Per Is

57 Providing and fixing standard extruded of aluminum 22.00 SqM 1175.56

section of size 63mm x 38.10mm x 1.2mm (of Jindal

Section no:2434@ wt. of 0.643 kg/mt), with colour Powder

coated aluminum frame ventilation with 5mm thick frosted

glass as details etc. complete for Ventilation.

58 Providing and laying 18 mm thick mirror polished black 888.00 SqM 2493.69

granite stone machine cut in single piece (Max. available) in

sill and jambs laid over 10 mm thick cement mortar 1 : 3 (1

cement : 3 coarse sand) and jointed with grey cement slurry

with matching pigment incl. rubbing and polishing half

rounding edge etc. complete colour and shed as approved

by architect engineer in charge.

59 Providing and fixing safety grills of Required pattern for 24806.20 Kg 111.47

Windows, Door using required size of MS polished bars at

specified spacing inserted and welded from inside to

rectangular box type frame CRC Pipes of Required Size at

required spacing as per design and hold fasting with coach

bolts including one coat of primer and two coats of Matt

finished oil painting etc. complete.

60 Providing and laying Machine Cut free edges, Machine 112.00 SqM 2344.21

polished Granite Stone slab 18 mm thick single piece

For Stair,Steps,landing as per design incl. full moulded

round front edge and 1cm nosing and necessary groove on

trade of steps laid on 20 mm thick cement mortar 1:6 (1 -

cement : 6 coarse sand ) jointed with grey cement slurry

including rubbing, polishing & Finishing etc. complete

61 Providing and laying machine cut Mirror Polished 60x60 cm 1925.00 SqM 1001.14

size Blue Kota stone slab 25mm thick flooring over 20mm

(Average) thick base of cement mortar 1:6 (1-cement : 6-

coarse sand) or L.M. 1:1.5 and laid over and jointed with

grey cement slurry including rubbing and Mirror polishing

with emery stone No 600 etc. complete.(A) 25mm thick

62 Providing and laying machine cut Mirror Polished Blue Kota 149.00 SqM 1149.52

stone slab 25mm thick Risers of Steps. dedo and

pillars laid on 10mm thick Cement Mortar 1: 3 (1-cement

: 3-coarse sand) and jointed with grey cement slurry

including rubbing and semi mirror polishing with emery stone

No.600. complete.(A) 25mm thick

Item Description of Item Qty. Unit Rate In Amount in Rupees

63 Providing and laying 60x60 cm size (for general space in 239.00 SqM 1022.12

toilet ) and 30x30 cm size ( for W.C., Bath and attached

toilets) 10mm thick antiskid ceramic Tiles in flooring

treads of steps and landing laid over 20mm (Average) thick

base of cement mortar 1:3 (1-cement : 3-coarse sand) laid

over and jointed with white cement slurry including finishing

with flush pointing and cleaning the surface etc. Complete.

64 Providing and laying 30x60 cm white (any colour as 903.00 SqM 970.17

approved by engineer) glazed tiles 6mm thick in skirting

risers of steps and dedo on 10mm thick cement plaster 1:3

(1-cement : 3-coarse sand) and jointed with white cement

65 Providing and laying water proofing treatment with China 986.00 SqM 1057.84

mosaic tiles flooring over avg 40 mm C.C. 1:2:4 {1 Cement :

2 sand : 4 Kapachi / Gritt 6 to 12 mm size} bedding for

maintaining slope for plain and curve surface & 12 mm to

mm of broken piece of ceramic / glazed tiles ( one for more

color as directed ) to be laid over cement mortar bedding of

C M 1:3 (1 cement : 3 sand ) containg one Kg of water

proofing materials per bag of O P C at plain or / and slops

and to be tempered to bring mortar ceramic up to surface

with using white cement and colour pigment including

rounding of junctions and extending them up to 15 cm along

the wall and curing with bends any pattens or design as per

drawing and cleaning by using oxalic acid etc. complete.

66 Providing and laying Both Side machine Double Side 17.00 SqM 1997.78

Polished Granite Stone slab 18 mm thick average thick

of approved quality incl. full moulded round front edge fixed

in wall for Partition and jointed with white cement slurry

including rubbing, polishing & Finishing etc. complete

67 Wall painting (Two coats) with plastic emulsion paint of 11193.00 SqM 121.46

approved brand and manufacture on undecorated wall

surface to give an even shade including thoroughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth. including Applying two

coats of Birla or Asian acrylic lapy ( putty) & two coats of

primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly brushing

the surface free from mortar dropping and other foreign

matter and sand papered smooth.

68 Wall painting (Two coats) with plastic emulsion paint of 2957.00 SqM 127.01

approved brand and manufacture on undecorated wall

surface to give an even shade including thoroughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth. including Applying two

coats of Birla or Asian acrylic lapy ( putty) & two coats of

primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly brushing

the surface free from mortar dropping and other foreign

matter and sand papered smooth. on ceiling and Soffits s of

Item Description of Item Qty. Unit Rate In Amount in Rupees

69 Wall painting two coats with weather proof acrylic 2985.00 SqM 117.40

emulsion APEX type paint of approved brand &

manufacture and of required shade on exterior wall surface

to give an even shade over and including a primary coat

with alkali resistance primer of approved brand after

thoroughly brushing surface to remove all dirt and remains

of loose powdered materials etc. comp. for all height.

70 Providing and fixing 90 cm high Stainless steel railing 55.00 Rmt 3871.33

316 Grade made from anticorrosive S S pipe of 50 mm dia

(16Gauge) as hand rail with S S 32 mm dia (16Gauge) as a

vertical support fixed in RCC slab at 1.2m c/c including

three horizontal S S pipes of 16 mm dia (16Gauge) at

equal distance fixed by 18.75 mm dia (16Gauge) S S pipe

including accessories as per detailed drawing as directed

71 Providing laying and jointing in true line and level 40mm dia. 600.00 Rmt 148.12

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two meter C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

72 Providing laying and jointing in true line and level 25mm dia. 300.00 Rmt 91.84

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two meter C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

73 Providing laying and jointing in true line and level 15mm dia. 200.00 Rmt 72.65

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two meter C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

74 Providing and fixing PVC SWR Nahni trap IS 14735 for 45.00 No 572.32

drain - 75 mm diameter with jali of the following nominal

diameter of self cleansing design with C.I scread down or

hinged grating including the cost of cutting and making good

75 Providing and fixing S.W. gully trap with C.I. grating brick 10.00 No 1246.92

masonary chamber and water tight C.I. cover with frames of

300mm x 300mm size (Indian) with standard weight (i)

square mouth traps (ii) 150mm x 100mm size 'P' or R type.

76 Providing and fixing screw down bib taps of following 90.00 No 186.83

size.(A) Brass screw down bib tap polished bright. (i)

77 Providing and fixing chromium plated brass half turn type 60.00 No 263.77

Flush cock of approved quality including fixing in pipe line

.(ii) 25mm dia.

Item Description of Item Qty. Unit Rate In Amount in Rupees

78 Providing and fixing Flat back wash basin Colour glazed 20.00 No 1965.46

630 x 510 size (Brand Varmora or equivalent) with C.P.

brass waste for washbasin or sink. & 32mm pillar tap, Bottle

trap capstan head, screw down high pressure with screws,

shanks and back nuts. (i) 32mm dia. Providing and fixing

brass screw down stop tap. (A) 32mm dia..

79 Providing & Fixing stainless steel sink Glossy ASIS 304 6.00 No 2207.86

Grade and 1 mm thick with with over all size 610x460 mm &

bowl size 560x410x200 of Nirali brand or Equivalent with all

fitting C I Or M.S Brackets painted white /or fixing on stone

base including cutting holes and making good the same

brass wastw and M I fisher union fitting including all

necessary fitting.

80 Providing and fixing water closet squatting pan ( Indian type 10.00 No 1350.73

W.C. Pan of Hindustan, Cera, Parrywareor, hindware,)

or equivalent size 580 mm including 100mm size P or S

trap for water closet squatting pan including jointing the trap

with the pan and soil pipe in cement mortar 1:1 etc.

81 Providing and fixing wash down water closet European 10.00 No 3536.01

W.C. Pan with integral P or S trap and Suitable flush tank

with complete fittings including cutting holes in walls and

making good the same connecting the flush bend with

cistern and closet etc. complete including plastic seat cover

and including jointing trap with Waste pipe overall size as

per the selection of the Model by E.I.C. or as approved}

82 Providing and fixing Urinal of approved quality including 9.00 No 1597.91

connection with trap and with integral longitudinal flush

pipe.(A) Squatting plate pattern white earthenware 550mm x

83 Providing erecting and fixing double coated Syntex or 34000.00 Ltr 3.95

equivalent PVC(ISI) mark water tank of required capacity

each with all necessary fittings and connection etc.

Complete on terrace.

84 Providing and fixing 600 mm x 450 mm beveled edge 20.00 No 854.58

mirror of superior glass mounted on 6 mm thick A.C sheet

or plywood sheet or PVC framing and fixed to wooden plugs

with C.P. brass screw and washers.

85 Providing and fixing C.P. brass towel rail complete with 36.00 No 616.42

C.P. brass brackets fixed to wooden plugs with C.P. brass

screws (B) 600 mm X 20mm size..

86 Providing and fixing 600mm x 120mm glass shelves with C 36.00 No 534.82

P Brass brackets and guard rail complete fixed to wooden

plug with CP Brass screw etc. complete.

87 Providing and fixing Gun metal check or non-return full way 18.00 No 420.63

wheel valve.(E) 25 mm dia.

88 Providing and fixing Gun metal check or non-return full way 18.00 No 663.43

wheel valve.(E) 40mm dia.

Item Description of Item Qty. Unit Rate In Amount in Rupees

89 Providing laying and jointing in true line and level UPVC 225.00 Rmt 834.38

SWR pipe Type B pipe confirming to IS 13592 -1992 with

one end plain and other end socketed with rubbering &

fitting confirming to ISI 14735-1999 of approved make for

drainage system pipe line, pipe shall be jointed with each

other with rubber lubricant, pipe shall be fixed on wall using

of PVC clamp of the size 160mm diameter x 210mm length

x 196mm high at every 2000mm center to center or shall be

concealed in wall as directed including necessary fitting such

as bends, shoes etc. including testing of pipe and joints and

jointed with adhesive solvent cement including cost of all

materials.75 mm Dia

90 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 435.00 Rmt 339.05

working pressure poluthene pipes of the following outside

Dia. Low density, complete with special flange compression

type fittings, wall clipsetc. including making good the wall

ceiling and floor.(G)110 mm

91 Providing and Fixing in position cowel vent to pipe 75mm 9.00 No 393.04

dia as directed.

92 Providing and Fixing in position cowel vent to pipe 100mm 6.00 No 505.17

dia as directed.

93 Providing and filling with good quality cinder (steam coal) 128.00 CuM 778.71

as directed by engineer in charge in sunk in layers of 15 cm

thk, including watering, placing, ramming well etc. as

94 Providing, laying and filling 50mm thick expansion joint by 79.00 SqM 1491.03

hydro cell semi rigid UV resistance with high performance

laminated closed cell polythene foam joint filler in sheet

foam as directed etc. Complete.

95 Providing, laying and filling the expansion joint by Thiol flex 113.00 Rmt 515.39

600 polymer or equivalent confirm to BS 4254-1983 as per

required shade and manufacture specification by making

groove of 50mm x 12.5mm lather by cutting or any other

foreign material including applying primer and filling required

size ( over of joint PU foam )as directed etc. Complete.

96 Providing and fixing 25cm wide and 3mm thick exterior 156.00 SqM 1054.34

composite panel on existing expansion horizontally and

vertically with all material, hardware, accessories and fitting

97 Providing and fixing in position 300mm high,150mm wide 75.00 No 707.00

English/Gujrati letters made from 1.0mm thick stainless

steel sheet as directed by Engineer in charge with all

material, hardware, accessories and fitting etc. Complete.

98 Providing and fixing in position 150mm high, 60.00 No 404.00

English/Gujrati letters made from 1.0mm thick stainless

steel sheet as directed by Engineer in charge with all

material, hardware, accessories and fitting etc. Complete.

Item Description of Item Qty. Unit Rate In Amount in Rupees

99 Constructing Sandwich Platform of 18 mm thick Polished 36.00 SqM 3744.07

Black or selected Granite at top and 25 mm thick Kota stone

slab With 75CM height with necessary Support using 20mm

thick cement mortar 1:3 for sandwich and fitting at bottom &

edges with waterproof rigid adhesives including making

necessary grooves in walls with Vertical support of double

Kota stone sandwich every 60 cm center to center including

all labour material of approved quality including full

moulded round front edge fixed in wall for partition and

jointed with grey cement slurry including rubbing and

polishing etc. complete

100 Providing and fixing railing of M.S. square pipe as per 134.00 SqM 2168.47

pattern suggested by Engineer in Charge including providing

outlet vertical top and middle square pipes of 40mm and

intermediate horizontal and vertical square pipe of 20mm

size including cutting, bending, welding, jointing and fixing

on site including painting two coats etc. complete.

101 Providing and fixing ceramic board of required colour with 19.00 SqM 7575.00

25mm x 19mm aluminum frame and BBS Plastic orner

hanging clamps tray for chalk with duster including fixing on

9mm particle board with 060mm galvanised steel surface on

back side and 060mm ceramic surface on front side as per

IS with necessary fixtures and fastening etc. Complete.

102 Providing and fixing pre-cast Rubber Dye / steel Dye inter 392.00 SqM 704.07

locking concrete block 60mm thick with grade of concrete

M300 pneumatic compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the joint

with sand in proper line and level as per guidelines of IRC :

SP 63-2018 etc. Complete.

103 Providing & Fixing Colour anodized Aluminum Partition 108.00 SqM 2927.99

PARTLY PANNELED, PARTLY GLAZED using aluminum

section of Frame size 63.50x38.10x1.95 mm (of Jindal

Section no.4605 @ Wt.1.094 Kg/Rmt) Partly Glazed 5mmt

thick Modi Guard and Partly Fixed with 12mm thick exterior

grade both side prelaminated sheet including rubber gasket

and beading clips for Glazing/ panneling and cleat angle,

with expansion hold fasteners including necessary filling up

of gaps at Junction including all required materials labour

and equipment as per detailed drawing As Directed by

Engineer in Charge.

104 Providing and fixing eco-friendly light weight calcium 264.00 SqM 1674.15

silicate false ceiling tiles having Tegular edge & 15 mm

Thick Densified edges on the Tile Periphery for Extra

Strength The Light weight calcium silicate ceiling tiles shall

have , light reflection 85% non-combustible as per B.S.

part IV, 100% humidity resistance and also having thermal

conductivity0.043° w/m KC.for the best thermal Insulation .

The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/ Spintone/Cosmos having NRC value

of 0.5 & Globe having NRC value of 0.75 NRC or equivalent

of size 595 X 595 mm to be laid on true horizontal level

suspended inter locking metal grid of hot dipped galvanized

Item Description of Item Qty. Unit Rate In Amount in Rupees

(galvanizing @120 grams per SqM including both side) consisting

of main ‘T’ runner suitably spaced at joints to get required length

and size of 24X38mm made from 0.30 mm thick (minimum)

sheet, 1200mm center to center, and cross ‘T’ of size 24X28mm

made out of 0.33mm (Minimum) sheet spaced 1200mm along

spaced between main ‘T’ at 600mm center to center to form agrid

of 1200X600mm andsecondary cross ’T’ of length 600mm and

size 24x28mm made of 0.30 mm thick (Minimum) sheet to be

interlocked at middle of the 1200X600mm panel to form grid of

size 600X600mm resting on periphery walls/partitions on a

perimeter wall angle pre-coated steel of size (24X24X3000mm

made of 0.40mm thick (minimum) sheet with the help of rawl

plugs at 450mm center to center with 25mm long dry wall screws

@ 230mm interval and laying 15mm thick Densified edges light

weight calcium silicate ceiling tiles of approved texture (Fine

Fissured/Cosmos/Spintone) in the grid including, cutting /making

opening for services like diffusers, grills, light fittings, fixtures,

smoke detectors etc.

, wherever required, Main ‘T’ runners to be suspended from

ceiling using G.I. slotted cleats of size 25X35X1.6mm fixed to

ceiling with 12.5mm dia and 50mm long dash fasteners, 4mm G.I.

adjustable rods with galvanized steel level clips of size

85X30X0.8mm, spaced at 1200mm center to center long main ‘T’

bottom exposed with 24mm of all T-sections shall be pre-painted

with polyester baked paint, for all heights, as per specifications,

drawings and as directed by engineer-in-charge. Note:- Only

calcium silicate false ceiling area will be measured from wall to

wall. No deduction shall be made for exposed frames/opening

(cut outs) having area less than 0.30 SqM. The calcium silicate

ceiling tiles shall have NRC. Value of 0.50 (Minimum) for Fine

fissured/Spintone/Cosmos and 0.75 NRC for Globe, light

reflection 85% non-combustible as per B.S. 476 part IV, 100%

humidity resistance and also having thermal conductivity. 0.043°

w/m KC.for the best thermal Insulation

105 Providing and Fixing U shape 600mm x 100mm hand rail 2.00 No 8585.00

(Cera) made from SS Bars with AntiSlip Coating for

handicap toilet as per engineer in charge instruction

106 Providing and Fixing vertical grab bar 600mm long (Cera) 2.00 No 5555.00

for handicap toilet (as per engineer in charge instruction

107 Providing and fixing 50mm Dia "Z" Clamp as per direction. 220.00 No 141.40

108 Providing and fixing Chemical Anchor boult of Hilti 900.00 No 252.50

equivalent With nut bolts wiser plate completed including

chemical Drilling 12 mm Dia With all fixer

109 SIGNAGES ON WALL 150.00 No 1010.00

Providing, Fabricating & Fixing wall signage's using

grade Stainless steel brushed steel finish plate of 1.5 mm

thick fixed on a wall using s.s studs including punched (laser

cut) lettering carried out on s.s plate of required size and text

as directed by Engineer over the S.S plate etc. complete.

Size:(45 cm x15 cm)

110 Place Identification Sign :-Providing and fixing sign boards 1.00 No 12341.52

made out of 2mm aluminum sheet / 4mm ACP (Aluminum

composite Panel); size 150x90 cms. rectangular as per

design of IRC-67-2012. Pre treated with phosphating

process & acid etching; coated with one coat of epoxy

primer and two coats of best quality epoxy paint ;

reflectorized with High Intensity Prismatic Grade retro

refiective sheeting of Type-4 as per ASTM D-4956 and latest

M.O.S.T. Specifications; 4.0mtr (2 Nos.) long stand post of

Iron Angle 75 x 75 x 6mm / 65NB Circular MS Pipe as

Item Description of Item Qty. Unit Rate In Amount in Rupees

frame fabricated from suitable size iron angle of 35 x 35 x

3mm; painted with best quality epoxy coatings in black and

white bends. The details of symbol for each board shall be

as per the instruction of engineer in charge. The fixing at site

shall be in 1:2:4 CC block of size 45 x 45 x 60 Cms. for each

leg including excavation, curing etc. Complete under the

supervision of engineer in charge. A warranty for 7 years for

the Retro reflective sheeting from original manufacturer & a

certified copy of 3 year outdoor exposure test report from

third party test lab for the product offered shall be submitted

by contractor. (B) Class-B Type-4 Retro Reflective sheeting

111 Providing and fixing pillar tap, capstan head, screw down 20.00 Each 308.73

high pressure with screws, shanks and back nuts. (i)15mm

112 Providing and fixing in position collapsible steel shutters 6.00 Quintal 5941.61

with vertical channels 20 x 10 x 2 mm braced with flat iron

diagonals 20 x 5 mm size with top and bottom rails of T_rin

40x 40 x 6 mm with 38mm dia, steel pulleys complete with

bolts, nuts, locking arrangements, stoppers handles

including applying a priming coat of red lead paint

113 Supplying Handicap steel wheel chair with fixed arm rest 2.00 No 7575.00

and leg rest with 8" PVC Castor and 24" Solid Mag Wheel

with as per instruction of engineering In charge.

114 2mm Aluminum / 4mmACP sheeting fixed with Type-4 210.00 SqM 4713.67

Class-B High Intensity Grade Sheeting as per IRC 67 :

reflective sheeting of size including lettering and signs as

115 Providing and fixing machine cut Double polished kota 148.00 SqM 616.10

stone in single piece (Max 150 cm long and width up to

cm with both side polished) for horizontal Shelves

including making grooves & Fixing the Same finished with

flush pointing, round open edge etc. complete

116 Providing and fixing 120 cm high Stainless steel railing 241.00 Rmt 4079.39

316 Grade made from anticorrosive S S pipe of 50 mm dia

(16Gauge) as hand rail with S S 32 mm dia (16Gauge) as a

vertical support fixed in RCC slab at 1.2m c/c including

three horizontal S S pipes of 16 mm dia (16Gauge) at

equal distance fixed by 18.75 mm dia (16Gauge) S S pipe

including accessories as per detailed drawing as directed

117 Providing and filling rubbles including hand packing and 191.00 CuM 1086.50

filling interstices with quarry spalls behind abutments and

between returns as directed in foundation and plinth

including ramming, consolidating, dressing etc. comp. as

directed by engineer in charge.

118 P & F BRAILE INDICATOR OF SIZE 170 MM X 35MM 75.00 Rmt 732.25

FOR HANDRAILS OF THE APPROVED DESIGN AND

MAKE HAVE BRAILE DOTS RAISED 0.5 MM ABOVE

BASE PLATE TO BE INSTALLED AT SPECIFIC

LOCATIONS AS PER DIRECTION OF ENGINEER IN

Item Description of Item Qty. Unit Rate In Amount in Rupees

119 Earthwork for embankment including breaking clods, 3125.00 CuM 173.67

dressing with all lead and lift and including watering rolling

and consolidation of subgrade in layers at O.M.C.to required

dry density including filling the depression which occur

during the process using power roller 8T to 10T.(E) From

Borrow area within all lead and lift

120 Clearing and grubbing road land including uprooting rank 0.25 Hect. 28455.09

vegetation grass bushes, shrubs, sapling and trees girth up

to 300 mm removal of stumps of trees cut earlier and

disposal of unserviceable materials within all lead and lift (C)

By mechanical means in area of light jungle

121 Providing, laying and jointing in true line and level 160 mm 30.00 Rmt 1106.96

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring,

& fittings conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 160 mm diameter x 149 mm

length x 145 mm heigh at every 2000 mm center to center or

shall be concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of pipes

and joints and jointed with adhesive solvent cement

including cost of all materials.

122 Providing junction for rainwater Junction chamber of clear 15.00 No 3880.42

size 0.60 x 0.60 x 0.75 m with excavation of size 1.04 x

m and 0.15 mt thick C.C 1:2:4 bed concrete including half

brick masonry wall in c.m 1:4 of 0.75 m height with 15mm

thick cement Plaster with floating coat of neat cement slurry

inside and 0.10 mt thick 0.84 X 0.84 size R.C.C (1:2:4 )

slab with TMT steel and 0.60 m x 0.45 m cast iron manhole

cover with frame with weight not less than 35 kg as per

detailed drawing as directed

123 Providing filter chamber of brick work in C.M. 1:5 of clear 2.00 No 14491.48

size 2.06 m x 1.21 m x 1.20 m and excavation dimension

of 2.36 x 1.51 x 1.35 m including C.C 1:2:4 bed concrete of

0.15 m thick including brick work in c.m 1:5 for 23 cm thick

wall including 15mm thick cement plaster inside with

floating coat of neat cement slurry and 10 cm thick RCC

1:2:4 top cover with TMT steel and manhole cover with

frame of minimum weight of 35 kg and filing filter material

Kapchi and sand as per detailed drawing

124 Providing Rainwater Harvesting 2m x 2m x 4m Pit for 2.00 SqM 119904.17

water logging with excavation in any strata upto4m depth

filling the pit with brick bat in 0.6 in depth 0.30m depth with

10mm to 20mm Kapchi 0.40m depth with 6x 10mm grade

and 2.00mt Depth with course sand in layers including

making 100 mm dia PVC Line for water inlet etc. as directed

250mm dia bore up to 50mt depth and 150 mm dia plain of

perforated PVC pipe casing 48mt Depth and making

concoction etc. complete as directed for recharge well for

rain water harvesting

125 Box cutting the road surface to proper slope and camber 337.00 CuM 212.58

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed including all lead and lift

Item Description of Item Qty. Unit Rate In Amount in Rupees

126 Construction of granular sub-base 150 mm thick by 123.00 CuM 3685.01

providing coarse graded machine crushed B.T. material

satisfying MOST specification of grading II (B.T. stone

aggregate 26.5 to 4.75 mm - 75 % and 2.36 mm below -

% ) including spreading in uniform layer with motor grader

on prepared surface, mixing by mix in place method with

rotavator at OMC and compacting with vibratory roller to

achieve the desired density etc. complete.

127 Providing and laying in foundation cement concrete 1:3:6 (1 81.00 CuM 3357.24

cement : 3 coarse sand :6 20mm B.T. Stone aggregate) and

curing complete excluding cost of form work in :(a)

Foundation plinth.

128 Providing and laying controlled cement concrete M. 200 for 114.00 CuM 5187.36

Trimix Cement Concrete Road and curing complete

including cost of formwork but excluding cost of

reinforcement for RCC road by using floater, vacuum,

dewatering process incl. making groove for joint ct. 5 m c/c

& at full depth of the thickness and 5 to 10 mm wide by

diamond cutter and filling the joints with polysyphide etc.

129 Providing and fixing pre-cast Rubber Dye / steel Dye inter 800.00 SqM 704.07

locking concrete block 60mm thick with grade of concrete

M300 pneumatic compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the joint

with sand in proper line and level as per guidelines of IRC :

SP 63-2018 etc. Complete.

130 Providing and fixing pre-cast concrete kerb stone of gray 126.00 Rmt 394.59

cement based concrete block 30cm length,30cm height and

15cm thick of M200 grade concrete as per approved design

and including excavation for fixing in proper line and level,

filling the joint with C:M 1:3 (1cement:3fine sand) etc.

131 Providing ISI Mark T.M.T. bar Fe 500D reinforcement for 11150.00 Kg. 77.29

R.C.C work including bending, binding and placing in

position complete up to floor two level For All Floor

132 Supplying promoulded bituminous joint filler.(i) 12mm thick 10.00 CuM 553.79

133 Direction sign (Junction board):-Providing and fixing sing 4.00 No 14831.71

boards made out of 2mm aluminum sheet; size 244 x

122cms. rectangle as as per the design of IRC-67-1977 pre

treated with phosphating process & acid etching; coated with

one coat of epoxy primer and two coats of best quality epoxy

paint; reflectorized with retro reflective sheeting as per latest

M.O.S.T. Specifications; Letters and numerals should be as

per IRC-30-1968, 3.1m long (2 nos) stand post and frame

fabricated from suitable size iron angle of 50 x 50 x 5mm

75x75x6mm as required; painted with best quality epoxy

coatings in black and white bends. the details of symbol or

inscription / numerals for each board shall be as per the

instruction of engineer in charge. The fixing at site shall be in

1:2:4 CC block of size 45 x 45 x 60cms. for each leg.

including excavation curing etc. complete under the

supervision of engineer in charge.(A) Engineer Grade

134 Providing and Fixing Signages (Acrylic Name Plates) having 15.00 No 656.50

size of 315 x 200 x 5 mm thick displaying Names of Offices,

Room, Toilet, Passage etc. having fonts, colour as directed

by the Engineer in Charge.

Item Description of Item Qty. Unit Rate In Amount in Rupees

135 Supplying & erecting carbon dioxide ( CO2 ) fire 34.00 No 6591.26

extinguisher user of following capacity with necessary

clamps made from 50 x 6 mm M.S. flat with nut & bolts

grouted in wall complete ( A) For 4.5 kg capacity

136 Supplying & erecting ABC powder type 'ceasefire' type 34.00 No 5090.40

fire extinguisher as per IS 13489 or 1 kg capacity with

necessary clamp for erection on wall

137 Pressure booster pump of 450 lmp capacity 1.00 No 75000.00

Item Description of Item Qty. Unit Rate In Amount in Rupees

138 Providing laying (to level or slopes) and jointing reinforced 350.00 Rmt 678.01

concrete Light duty non-pressure pipes I.S. class NP2 of the

following internal diameter with collars and butt ends

prepared for collar joints including testing of joints

complete.(D) 300mm

139 Constructing brick masonry chamber for under ground C.I. 16.00 No 3660.76

Inspection chamber and bends with bricks having crushing

strength not less than 35 Kg/cm2 in cm. 1:5 C.I. Cover with

frame (light duty) 455 mm. X 610 mm. Internal dimensions,

total weight of cover with frame to be not less than 38 Kgs.

weight of cover 23 Kg. and wt. of frame 15 Kg) R.C.C. top

slab with 1:2:4 mix(1 cement : 2 coarse sand : 4 graded

stone aggregate 20 mm. size ) foundation concrete 1:5:10

inside plaster 15 mm. thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls & abed

concrete etc. complete.(ii) Inside dimensions, 500 mm. X

700 mm. And 450 mm. Deep for pipe line with one or two

140 Constructing brick masonry chamber for underground C.I. 32.00 No 2932.93

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of

cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe

with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(i) Inside dimensions 455mmx

610mm and 450mm deep for single pipe line.

141 Extra over items for every additional depth of 0.1 m or 10.00 No 264.86

part there of beyond 450 mm depth for brick masonry

chamber (i) for 500 mm x 700 mm

142 Extra over items for every additional depth of 0.1 m or 15.00 No 242.39

part there of beyond 450 mm depth for brick masonry

chamber (i) for 450 mm x 610 mm

143 Providing, laying and jointing in true line and level 160 mm 220.00 Rmt 834.38

diameter U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber ring,

& fittings conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 160 mm diameter x

mm length x 196 mm heigh at every 2000 mm center to

center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

Item Description of Item Qty. Unit Rate In Amount in Rupees

144 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- 12.00 No 23470.48

cement :2-coarse sand : 4-graded stone aggregate 20mm

nominal size) foundation concrete 1:3:6 mix (1-cement : 3-

coarse sand :6-Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:5 (1-Cement : 5-coarse

sand) finished with a floating coat of neat cement and

making channels in cement concrete 1:2:4 mix (1-Cement :2-

Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i)

Inside size 900mm x 1200mm and 1.5M. deep including C.I.

cover with frame size 560mm diameter total weight of cover

and frame to be not less than 128 kgs. (Wt. of cover 64 Kg.

and Wt. of frame 64 Kg.)(A) With 230mm thick walls of brick

masonry using brick having crushing strength not less than

35Kg. / Sq.cm. in Cement Mortar 1:5 (1- Cement: 5-Coarse

sand) (2) C type depth 2.25 Meter for 150mm diameter

145 Providing and Construction 2.28 mt. inner dia and 6.50 mt. 4.00 No 53205.79

deep sock pit including excavation BBCC. Brick masonry

work at bottom and top including RCC Slab at top in honey

combica masonry in mud goober as directed.

146 Providing Septic tank of size 4.95x1.98x2.50 mt. depth 2.00 No 93806.78

including necessary excavation and 23 cm thick RCC wall

and horizontal portion with bottom concrete 1:5:10 and

mm thick IPS and 15 mm thick inside plaster 12 cm thick cc

1:2:4 slab with two manhole cover including connection with

sock pit and other sanitary items

147 Drilling of 250/300 mm dia bore in over burden strata in 320.00 Rmt 576.71

hard and rock information by DTH rig including lowering of

pipes and vertically and testing etc. including testing with

148 Reaming of 250 mm dia pilot bore hole to 550 mm dia 320.00 Rmt 351.48

bore hole including assembling, jointing, lowering housing

casing, strainer pipe, Gravell packing, clay packing etc.

comp from 250/300mm dia to 550mmm dia bore hole rom

0.00 mts to 330.00mts

149 Supply of clay balls having size of 15mm to 25mm made 12.00 CuM 758.51

from sticky clay on site

150 Supply of ERW blank pipe of approved quality at site of 320.00 Rmt 2431.07

work confirming to IS 1239-1964 200 mm dia (Min 6.00 mm

151 Supply of gravel having size 4mm to 6mm as directed on 12.00 CuM 2049.29

152 Reducer made from 6 mm thick plate (MS.) for 1865.61 1.00 No 1884.27

1884.27 No ERW pipes of size as below(ii) 200mm dia X

250 mm dia. X 600 mm length

153 Supplying 3 Phase Borewell Submersible Pump Set 1.00 No 67501.33

suitable for bore of 100 mm dia or more having three phase

motor capacity Electric motor driven borewell submersible

pump set confirming to IS 8034 and motor confirming to IS

9283 working at 3 phase 400 / 440 volt 50 Hz AC supply &

2900 RPM cat 8.5-60 HP, 198 mt head, 800 Ipm discharge

Item Description of Item Qty. Unit Rate In Amount in Rupees

154 Supplying & erecting approved make 3 phase motor 2.00 No 23821.86

control cubical panel (Star Delta) made from 16 G CRCA

sheet duly painted with epoxy powder painted inside and

outside with hinged doors and locking arrangement.

consisting of suitable size of ON-OFF isolator (AC 3/23 duty)

main fuses, single phasing preventer cum water level Guard

(Complete unit). Toggle switch to by pass Single phase

preventer cum WLG, indicating lamps for R-Y- B phases,

over load relay, Automatic water level controller, Ammeter &

Voltmeter each with two way selector switch incoming wires

duly socket Crimped, Panel to be erected on angle iron

frame grouted on wall as directed Star Delta & main

contactor, overload relay, thermal Electronic Star delta cutoff

timer, start stop push buttons. The isolator overload relay &

contactors of L& T, Siemens or Cuttler Hamer make only.

Panel to be erected on angle iron frame ground on wall. (f)

S/D up to 30 H.P (L&T, Lubi, BCH make only

155 Lowering of submersible motor pump set complete with 1.00 No 2996.67

required. Nos, and size of casing pipes erected by means of

proper chain pulley block & pipe wrenches after checking of

threads of each pipe with coupling to take the load of the

pump set and pipe assembly filled up with water. (c)

(c)Above 120 mtr.

156 Providing and erecting ISI marked PVC insulated PVC 640.00 Rmt 146.45

shethed Flat flexible Submersible copper cable approved

make of following size. (c) 3 Core x 4 Sq.mm.

157 Providing water proof straight joint in PVC insulated flat 3.00 No 189.88

flexible copper cable by using insulating material, water

proofing material, & making the joint complete (A) Up to

158 Supplying ISI marked (Embossed) following size of Heavy 300.00 Rmt 538.33

duty "C" Class GI pipe & erecting as directed by Engineer

in Charge with necessary plumbing as desired (D) 80mm

dia. (Jindal, Asian, Tata make or equivalent make only)

159 Supplying and erecting with leak proof materials M.S. Heavy 40.00 No 151.50

duty ISI marked coupling having threads of 8 TPI/11 TPI

suitable for "C" class pipe to take load of pump and pipe

assembly of following size (A) 80mm. (G) 80mm (3") dia

160 Add cost of teak proof complete welding surrounding pipe 40.00 No 89.89

and coupling for use as column pipe for following size (A)

161 Cutting the heavy duty pipe and threading one end of pipe 40.00 No 140.39

with 8 TPI 11 TPI as per requirement and including to and

for charges (B) 80mm (3") dia Pipe (D) 80mm (3") dia pipe

162 Heavy duty clamp made from 4" x 1.5" iron strip suitable for 2.00 No 221.19

column pipe 15" to 2 length (D) 80mm (3) dia pipe

163 Supplying and erecting GI bend for pipe connections 1.00 No 273.71

suitable for (F) 80mm (3")

164 Charges for development of bore by giving air with 1.00 Job 22427.05

compressor for requirement as per site situation (600

CFM/150 PSI up to the depth, minimum 6 hours

165 Providing and laying in trenches galvanised mild steel 20.00 Rmt 921.68

tubes (medium grade) of the following nominal bore, and

tube fittings and black paint (H) 80 mm dia

Item Description of Item Qty. Unit Rate In Amount in Rupees

166 Slotting of MS ERW blank pipe of following size having slot 5000.00 Per Slot 0.40

size as 6. 75 cm x 6 35 cm x 3 12 mm (including unloading

of blank pipes from truck & reloading slotted pipes into truck)

2A (C) 300 mm dia

167 Providing and laying controlled cement concrete M.250 and 44.00 CuM 4526.87

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in Slabs,

landing, shelves, Balconies, Lintels, Beams, Girders and

Cantilever up to floor two level.

168 Providing and laying controlled cement concrete M.250 and 31.00 CuM 4551.51

curing complete including the cost of formwork and

excluding the cost of reinforcement for reinforced concrete

work in (B) Walls, from top of foundation level up to floor two

169 Providing and laying controlled cement concrete M.250 and 4.00 CuM 4628.14

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (D) Columns,

Pillars posts and struts, up to floor two level

170 Providing formwork of ordinary timber planking so as to give 299.00 SqM 239.69

a rough finish including centering shuttering strutting and

propping etc. height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of

the same for in situ reinforced concrete and plain concrete

work in. (C) Vertical surface such as walls (any thickness)

partitions and the like including attached buttresses & string

course & the like.

171 Providing formwork of ordinary timber planking so as to 71.00 SqM 260.88

give a rough finish including centering shuttering strutting

and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and removal of

the same for in situ reinforced concrete and plain concrete

work in. (B) Flat surfaces such as soffits of upspened floors

slabs Landings and the like. (1) Floors etc. up to 200 mm in

172 Filling available excavated earth (excluding rock) in 31.00 CuM 133.65

trenches, plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each deposited

layer by ramming and watering etc. complete

173 Providing and laying controlled cement concrete M.200 and 1.00 CuM 4460.86

curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in Slabs, landing,

shelves, Balconies Lintels, Beams, Girders and Cantilever

up to floor two level.

174 Providing and laying cement concrete 1:2:4 (1- Cement : 2- 1.00 CuM 6544.13

Coarse sand : 4- graded stone aggregates 20 mm nominal

size) for reinforced concrete Chhajja not exceeding 10cm.

thickness up to floor two level including finishing the

exposed surfaces with cement mortar 1:3 (1-cement, 3 Fine

sand) to give a smooth and even surface centering and

formwork and curing complete excluding cost of

Item Description of Item Qty. Unit Rate In Amount in Rupees

175 Providing and fixing mild steel door with 40 x 40 x 6 mm 214.00 Kg 111.50

angle for frame and for shutter frame 30 x 30 x 3 angle. For

windows frame of angle 35 x 35 x 5 & for shutter windows

25 x25 x 3 mm size angle and 18 gauge sheet for panels &

10 mm dia bars at 10 cm c/c for grill and 40 x 6 mm flats on

edge of shutter, & 20 x 6 mm binding patti, including one

coat of primer and two coats of oil painting etc. comp. as per

detail / as directed by Engineer in charge.

176 Providing 15mm thick cement plaster (Mala Trowel 38.00 SqM 171.21

finish) in single coat on brick/concrete walls for interior

plastering up to floor two level and finished even and smooth

in (i) Cement mortar 1:4 (1-cement:4- sand) for Ground Floor

177 Providing 10mm thick cement plaster in single coat on 16.00 SqM 145.12

Ceiling for interior plastering up to floor two level and

finished even and smooth with a floating coat of neat

cement slurry in (i) Cement mortar 1:3 (1-cement:3-sand)

178 20mm thick sand faced cement plaster on walls up to 52.00 SqM 246.22

height 10 meters above ground level consisting of 12mm

thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm

thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc.

179 Providing 20 mm thick Water proof cement plaster for 128.00 SqM 306.96

sunk in single coat on bricks/ concrete wall for interior

plastering up to floor two level finished even and smooth (ii)

Cement mortar 1:3 (1-cement: 3-sand) and mixing

waterproofing materials of approved brand and manufacture

in cement mortar in proportion recommended by the

manufacturer for All Floors.

180 Providing and laying white glazed tiles 6mm thick in 96.00 SqM 939.18

flooring, treads of steps and landing laid on a bed of 12mm

thick cement mortar 1:3 (1-cement : 3-coarse sand )

finishing with flush pointing in white cement.

181 Distempering with dry distemper of approved brand and 54.00 SqM 48.27

manufacture (two coats) and of required shade on wall

surfaces of given an even shade, over and including a

priming coat of whiting after thoroughly brooming the surface

free from mortar dropping and other foreign matter.

182 Providing cement vata (10cm. x 10 cm. size) quarter round 76.00 Rmt 24.28

in cement mortar 1:1 including neat cement finishing,

watering etc. complete.

183 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 2.00 No 958.17

size having weight not less than 35Kg.

184 Providing laying and jointing in true line and level 50mm dia. 270.00 Rmt 195.67

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre C/C or shall

be concealed as directed including necessary fittings etc.

including testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Item Description of Item Qty. Unit Rate In Amount in Rupees

185 Providing, supplying and fixing ISI mark CI DF butterfly 4.00 No 1977.58

valve as per IS 13095 (latest edition) of following class and

diameter including all taxes, insurance, transportation,

freight charges, octroi, inspection charges, loading.

unloading. conveyance to departmental stores. stacking etc.

complete as per direction of engineer in charge Butterfly

valve IS 13095 with ISI mark PN 1.0 and 50mm dia

186 Providing and fixing PVC SWR Vent Cowl 110 mm dia 60.00 Kg 58.58

187 Providing, supplying and fixing monoset sub. Pump 3 2.00 No 15707.52

phase 400/440 vott, 50c/s. A.C. supply & 2900 RPM, as per

IS 14220 MOC Casing: CI- FG260, Impeller: Bronze & shaft

ELECTRICAL ITEMS

188 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire 309.00 Pt. 449.45

of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to 10 mtr

length , in below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic/Wooden box,

single mounting base frame covered with

textured/metallic/white front plate modules erected on / in

wall / ceiling as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as directed with medium

class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete.Cat-III

189 Point wiring for Two Way Controlled Light Point with 2-1.5 3.00 Pt. 560.55

sq.mm & earth wire of 1.5 sq.mm (green) both are of .ISI

marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires erected in below type of pipe with 6A Modular

type switches and following type of accessories erected on

PVC / Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected. with

necessary batten/angle holder or ceiling rose or

H.D.Connector as directed.with medium class Rigid PVC

pipe and accessories erected concealed in wall/ceiling

complete.Cat-III

190 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 191.00 Pt. 629.23

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular type switch

and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following

type erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete.Cat-III

191 Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr length,

in below type of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC / Metallic/Wooden box

covered with appropriate front plate modules erected on / in

wall / ceiling as per pipe erected with following type of

Item Description of Item Qty. Unit Rate In Amount in Rupees

(b) For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. 141.00 Pt. 697.91

Wire from mcb db board with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling

complete.Cat-III

192 Point wiring for on board Looped Plug with 6A Modular type 217.00 Pt. 241.39

switch & 5 pin socket erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall /

ceiling with following type accessories. Cat-III

193 Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front plate

, modules erected with necessary connections as per site

situation directed by Engineer In charge..

(b) 6/16Amp. Universal socket Cat-III 11.00 Ea. 190.89

(c) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB 11.00 Ea. 390.87

194 Providing and erecting ISI mark Medium class RIGID PVC 300.00 Mtr. 32.32

PIPES of following size complete to be erected on/in wall or

ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with following

25 mm dia of pipes, in approved manner as directed.

195 Providing and erecting Mains with 1.1 KV grade FRLS PVC 4654.00 Mtr. 78.78

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected concealed in /flushed on

wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of

following size. with medium class Rigid PVC pipe and

accessories. (b) 2 wire 2.5 sq. mm

196 Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling with

2.5 sq. mm copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of following size with

medium class Rigid PVC pipe and accessories.

(a) 2 wire 4 sq. mm 800.00 Mtr. 107.06

(b) 2 wire 6 sq. mm 160.00 Mtr. 140.39

(c) 4 wire 6 sq. mm 960.00 Mtr. 248.46

197 Providing & erecting Switch board for Computer or electric 13.00 Ea. 1081.71

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with

single mounting base frame covered with textured/metallic

/white front plate,modules erected with necessary

connections as directed 1 no. 6A/16A universal plug-switch

3 nos. 6A Switch 3 nos. 6A 5 pin Plug.For Modular Type

Accessories.Cat-III

198 Decorative call bell Ting-tong box type 250 volts complete 1.00 Ea. 68.68

Item Description of Item Qty. Unit Rate In Amount in Rupees

199 Supplying and erecting LED indoor fittings with LEDs of 238.00 Ea. 535.30

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED LED driver

efficiency > 85 %( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

Tube Light with integral driver , 36-40 Watts, Surge-2 KV, IP-

20, conventional 4 feet Cat-III

200 Supplying and erecting led lamps with following wattage 51.00 Ea. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp holders,

pf >= 0.5 LED Lamps integral type, with PC diffuser suitable

LAMP holder , 5 to 8 watts Cat-III

201 Providing & erecting Approved make Power Saving 50 Watt 191.00 Ea. 1948.29

Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete

having 3blades with aluminium blades with , canopy &

cm. down rod erected with earthing.(Make shall be approved

by Engineer in charge)

202 Supplying and erecting 19 / 20 mm. nominal bore Medium 194.00 Mtr. 108.07

Class M.S. Pipe down rod erected duly painted for fan

complete with proper insulation without leakage and earthing.

203 Supplying & erecting fan hook box of 10 mm M.S. round 194.00 Ea. 108.07

bar bounded to the RCC bars up to 50mm length each side

and pierced through a 16 Gauge M.S. box / Heavy Duty

PVC box complete erected concealed in Ceiling with

necessary finishing.

204 Supplying & erecting single phase approved make industrial 19.00 Ea. 2054.34

exhaust fan suitable for medium duty ring mounted low

noise operation suitable for medium duty having following

dia size and maximum speed in RPM , 305 mm dia

205 Providing suitable M.S. louver shutter of the Exhaust fan. 19.00 Ea. 368.65

206 Providing recess in wall or window frame suitable for 19.00 Ea. 189.88

erection of Exhaust fan complete with plastering and colour

washing to match the colour of the wall or window complete

with expanded metal in order to render the fitting in

accessible and the room water-proof.

207 Providing & erecting water cooler having storage capacity 3.00 Ea. 46648.87

150 Ltr. & cooling capacity 150 Ltr.per hour @ an ambient

temp of 45˚ C. The outlet temp. of the water should drop by

15˚C within a hour, The water cooler should be comprising

of hermetically sealed compressor, fan motor, condensing

unit, water tank surrounded by evaporating, coil,

thermostats, relay etc.complete with necessary inlet & outlet

connection. The body of water cooler will be made from

Stainless Steel..

Item Description of Item Qty. Unit Rate In Amount in Rupees

208 Supplying & erecting 5 stage single reverse osmosis water 3.00 Ea. 24394.53

purification system with M.S. powder coated frame, prefilter

housing with 'O' ring presediment filter GAC filter, carbon

filter suitable buster DC pump capacity 80 psi, mention with

40 psi inline type post carbon filter auto low & high pressure

switches with following size of storage tank & LPH capacity

& erected as directed.50 Ltr / Hr with 150 psi 2 nos booster

209 Supplying & erecting 20 Amp 10 KA ‘C Curve’ single pole 3.00 Ea. 527.22

MCB with 20 Amp. Plug socket, company fabricated powder

coated sheet steel enclosure erected as directed with

connection.[A] Metal Clad Socket with metal clad top Cat.III

210 Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for

(C) single phase incoming and horizontal single phase 3.00 Ea. 1492.78

outgoing.sheet steel double door (IP-43) 12 way

(F)three phase incoming and single phase horizontal type 18.00 Ea. 3412.79

outgoing Per phase isolation type (PPI) sheet steel double

211 Providing & erecting 415V MCB Four Pole Switch for

Lighting Load (B curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following capacity

212 Providing & erecting 240 V MCB double pole switch for 12.00 Ea. 278.76

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

capacity 6 to 32 Amp. .Cat-III

213 providing and erecting Miniature circuit breaker single pole 460.00 Ea. 112.11

6A to 25A suitable to operate on 240 V A.C. system and

having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat-III

214 providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max.

rating erected as directed

(i) 25Amp DP , Cat-iii 58.00 Ea. 1969.50

Item Description of Item Qty. Unit Rate In Amount in Rupees

215 Providing & erecting weather proof, dust & vermin proof, 5.00 Sq.Mtr 10468.65

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions & cable alley

as per requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size

of inter connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts, foundation

flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket,heavy

duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates excludes the

cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams) The panel shall

be supplied with following approved manufacturers with

following size.(A) locally fabricated panel board (i) with

216 (ii) With 550 mm. Depth 2.00 Sq.Mtr 13576.42

217 Providing and erecting Approved make Four pole moulded 11.00 Ea. 6173.12

case circuit breaker having breaking capacity ICU of 25 KA.

at 415 V,having normal current rating up to 25 A to 100A.

with Fixed thermal & magnetic release suitable to work on

A.C. supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

218 Providing and erecting Approved make Four pole moulded 4.00 Ea. 20946.39

case circuit breaker having breaking capacity ICU of 35 KA.

and above at 415 V . having normal current rating 250A.

with variable thermal & magnetic release suitable to work on

A.C.supply 50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing 16 G.M.S.

housing. ICS=100% of ICU only Cat III

219 Supplying and erecting triple pole & neutral 440V / 500V

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary

bus bar supports /insulators, main cable socket to each bar,

erected in existing cubical panel with necessary connections.

(A) Suitable for 100 Amp. Capacity 4.00 Ea. 1961.42

(C) Suitable for 300 Amp. Capacit 1.00 Rn 4909.61

220 Supplying and erecting approved make panel mounting type 5.00 Ea. 1275.63

Digital Voltmeter having 3 digits LED display, 0 to 750 AC

Volts range erected on existing panel board with all

connection, wiring etc .with manufacturers calibration

Item Description of Item Qty. Unit Rate In Amount in Rupees

221 Supplying and erecting approved make panel mounting type 5.00 Ea. 1558.43

Digital Ammeter having 3 digits LED display, external CT

operated, calibrated for 0 to 1000 Amps suitable to operate

on 500 Volt AC , erected on existing panel board with all

connection, wiring etc .with manufacturers calibration

222 Supplying and erecting Ammeter / Voltmeter selector switch 10.00 Ea. 317.14

for 3 phase AC Supply 500 V on existing panel board with

necessary connections.

223 Supplying and erecting approved make suitable panel 15.00 Ea. 43.43

indicator LED type lamp, lens cover, complete erected with

necessary connections.[9-2-9]

224 Providing & erecting L.T. Current Transformer with bar 15.00 Ea. 274.72

primary 50/5 to 1000/5 ratio 15 VA burden erected in

existing CRCA box duly secured with insulating materials

connected to the meter

225 Providing and erecting Approved make Earth fault Relay

suitable to mount with inter connection suitable to following

size of moulded case circuit breaker having CT ratio &

MCCB rating as following along with shunt trip 220V AC.

with all internal connections & complete erected in existing

226 providing and erecting Mains with ISI marked, 1.5KV grade

electrolyte multi stranded, annealed copper conductor with

heat resistant PVC insulated conforms to IS 694, IEC -

erected in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor starters &

control wiring) with required size of copper lugs, nuts and

bolts if required.

(b) One wire 1.50 sq. mm 32.00 Mtr 16.16

(f) One wire 10.00 sq. mm 456.00 Mtr 87.87

(h) One wire 25.00 sq. mm 16.00 Mtr 225.23

227 Cable Terminal ( ‘Plain" Type)Set of Four for

228 Solder less crimping type Copper lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

229 Solder less crimping type Aluminium lugs conforming to IS

suitable for cable of following size evenly crimped with high

pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner.

230 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand / Solid Aluminium conductor for 1.1 KV. to

be laid on wall with necessary clamps or in existing trench /

pipe of following size of cables

(B) 4 core 6 Sq. mm 630.00 Ea 124.23

231 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables

Item Description of Item Qty. Unit Rate In Amount in Rupees

232 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables

(C) 3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) 170.00 Ea 281.79

(G) 3 1/2 core 185Sq. mm ( 70 Sq. mm 1/2 core)(double 450.00 Ea 899.91

233 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 150.00 mtr 418.14

cable multistrand Aluminium conductor for 1.1 KV. to be laid

on wall with necessary clamps or in existing trench / pipe of

following size of cables. (J) 3 core 95 Sq. mm (Double Run)

234 Providing and erecting 18 G. M.S. termination box outdoor 1.00 ea 676.70

type suitable for- 1.1 KV PVC insulated armoured cable

complete erected with clamp, bolts, nuts etc. suitable of

following size of cables.(A) 3 core 70 / 95 Sq. mm

234 Providing and erecting Epoxy Outdoor / Indoor end 1.00 ea 536.31

termination Kit suitable for LT PVC insulated armoured

cable1.1 KV grade complete with ferrule bushing and

accessories and suitable clamps duly erected and

connected to the supply for all cores cables of following size.

234 Providing and, fixing heavy duty flange type brass cable

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for following

size of cables.

(E) 2 to 4 core 25 Sq. mm 2.00 Ea 51.51

235 Providing and, fixing heavy duty flange type brass double

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables.

236 Providing and erecting Pipe type earthing having 150 12.00 Ea. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

237 For using salt and charcoal / coke as required for pipe type 12.00 Ea. 171.70

Item Description of Item Qty. Unit Rate In Amount in Rupees

237 Supplying & erecting in earthpit of minimum bore dia. 5.00 Ea. 5842.85

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 80 mm having 80-200 Micron galvanising, Inner

pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications

with chamber and heavy duty cover (A)(approved make

OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing

resistane mentioned in test Certificate) & having back filling

compound of, Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar

content:- <2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time

Necessary test report must be submitted by Agency.[A] For

electrical installation up to 440 V Length of Pipe - 1 Mtr Back

filling compound - 1 Nos. of Bag of 15 Kgs..

238 [B] For Electrical installation up to 11 KV located in other 5.00 Ea. 7095.25

than normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg.

238 Providing and erecting required size HOT deep Galvanised 75.00 Ea. 77.77

iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT

panel board, Motors etc. using proper clamp.

239 Providing and erecting required size Copper strip for 75.00 Ea. 794.87

earthing of H.T. OCB / ACB/ Transformer, LT panel board,

Motors etc. using copper clamp

239 Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved

or embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and 12.00 Ea. 3345.12

,Light must have 440VAC line supply with over-voltage

protection.(above 36 to 48 watts Cat-III

(B) Flood Light (IP-65), Surge protection -4KV integral and 9.00 Ea. 8453.70

,Light must have 440VAC line supply with over-voltage

protection.above 120 to 160 watts Cat-III

Item Description of Item Qty. Unit Rate In Amount in Rupees

240 Supplying & erecting approved make SMC press moulded 9.00 Ea. 515.10

composite FRP. loop-in, loop-out approx. 2mm thick box

complete with Bakelite connector strip 5way(3P+N+E),DIN

rail for mounting mob & hinged doors as per requirement

having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable

clamps& earth bolt of (B) 250mm x 200mm x 100mm

[deep]size of box.

241 Supplying and erecting approved make Octagonal pole 12.00 Ea. 11411.99

made from HR sheet steel. The pole should be made as per

IS. and shall be coated with hot dip galvanizing as per IS

2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mmX7.5mm Din-Rail for

MCB Mounting, stud type terminal and arrangement for

cable termination to be erected With Suitable foundation

(Included) as per details given by manufacturer considering

site requirement.(E) 7 Mtr. Long 70 mm Top X 135 mm

bottom dia, 3 mm thickness with 225mmX225mmX16mm

base plate, 4-M20 Bolts and 600mm long with necessary

G.I. J Bolts .Approx Pole weight 67 kg

242 Providing and erecting street light pole bracket comprising

main B Class GI pipe of 4.2 cm/require outside dia.

complete with suitable B Class G.I sleeve tubing of approx.

45cms.length and suitable for 76.5 mm / 80mm. / require

size pole top having sufficient fasteners for fixing the

brackets and having spread of 1 mtr. length with suitable

rise as per site condition & suitable welded stiffener reducer

and nipple with check nut complete painted with one coat of

Red oxide / PU base primer and two coats of Aluminium /

PU paint. paint with following nos of arms.

[A] Single Arm bracket 1Mtr 12.00 Ea. 614.08

Item Description of Item Qty. Unit Rate In Amount in Rupees

243 Providing and erecting Three Phase IoT GSM/GPRS Central Control 1.00 Ea. 59916.23

& Monitoring System (CCMS) Panel for Streetlights Smart Feeder

Panel with 3 Phase GSM/GPRS CCMS Streetlight Controller with

LCD Display (1 Nos.). Streetlight Controller with Individual each

Phase Control (Energy Saving feature) and Spare relay facility.

Streetlight Controller having 10 years of reserved battery for RTC.

With 50 programmable schedule, month-wise offset settable facility,

Astronomic sunrise/sunset time programming in-built for year long

schedule. Operating Voltage @ 440 V AC with Over Voltage & Short

Circuit protection. 2 hour Battery Back-up for Streetlight Controller.

Panel to have 1 Nos. of 3 Phase – Class 1 Energy Meter for Energy &

Fault monitoring on CCMS Web Dashboard. Panel consisting of

Nos. of 3 Pole Contactors (3 x 18 A), 7 Nos. of 1 Pole Miniature

Circuit Breakers (32 Amp.) for Bypass, Input / Output supply

functionalities, 1 Nos. of 4 Pole Earth leakage circuit breaker for

safety protection. Standard lock & key facility for Panel security. Door

Switch for unauthorized access & tamper detection. Accelerometer for

panel movement detection & tamper alerts. Suitable amount of Wires,

Connectors, Terminal Blocks included in Panel. 16/18 gauge M S with

industrial exterior powder coated PP with seven tank process RAL

7035 All weather-proof Enclosure Panel having IP65 rating.

Waterproof Glands & Grounding Stand included. Dedicated IoT

communication GSM/GPRS SIM Card (with minimum 5 years of

recharge) for Wireless Communication with CCMS Web Dashboard.

5 Years Data Hosting & Server Charges to be included with CCMS

Web Dashboard. Load status, Live analytics, Energy Meter

monitoring (Parameters such as kW, kWH, PF, I, V), comparative

analytics, reports generation facility. Fault detection on web

dashboard. GIS Mapping of CCMS Panel on Web Dashboard.

Secured MQTT Communication for Cloud. Includes Android & iOS

Mobile Application. Local communication facility via Mobile

Application in case of GPRS connectivity failure.

244 providing and erecting Miniature circuit breaker single pole 21.00 Ea. 270.68

0.5A to 2A system and having breaking capacity 10 KA to

be erected in existing box. confirming to IS 8828/1996 with

ISI Mark Cat-III

245 Providing & erecting open well horizontal mono block pump 1.00 Ea. 18746.61

set with cast iron body, complete for three phase

submersible motor having. For 5 HP 3 phase open well

horizontal mono block pump set suitable for 1350 LPM to

310 LPM @ 10 to 42 Mtr head suitable for 50/65 mm dia

delivery pipe .Cat-III

246 Supplying & erecting approved make motor control cubical 1.00 Ea. 7722.46

panel (Direct - on - line) made from 16 G. CRCA sheet duly

epoxy powder painted inside and outside with hinged doors

and locking, arrangement consisting of suitable size of ON-

OFF isolator (AC - 3/23duty) main fuses, single phasing

preventer, indicating lamps for R- Y - B phases, overload

relay, Automatic water level controller, Ammeter, Voltmeter

each with two way selector switch incoming, wires duly

socket crimped, main contactor & overload relay, start - stop

push buttons, to be erected on angle iron frame grouted on

wall as directed. The isolator, overload relay & contactors

will be of L & T, Siemens or BCH make only.(A) DOL up to

247 Lowering of submersible motor pump set at the depth of 1.00 Job 856.48

following ,complete with required. Nos. and size of casing

pipes erected by means of proper chain pulley block & pipe

wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe assembly

filled up with water For Open well Horizontal submersible

pump set for sump well (i) 1 HP to 5 HP

Item Description of Item Qty. Unit Rate In Amount in Rupees

248 S.I.T.C. submersible pump set suitable for bore of 150 mm 1.00 Ea. 39659.67

dia or more having 3 phase motor capacity not less than

HP with following capacity. Lifting and Lowering taken

extra.[A] 10 stage 575 to 480 LPM discharge at 60 to 70 mtr

head for 65 mm dia delivery pipe.Cat.III [9-6-6]

249 Providing and fixing approved make Perforated C type cable

tray. Made from sheet steel. The cable tray should be

single or double bended as per required and as per IS

2062/1079 and shall be coated with hot dip galvanizing as

per IS 2629/4759. with max 17.5% perforation with coupler

plate / Fish plate and GI hardware like nut - bolt and

washers etc. erection with necessary support( included) as

per Specification and as per instruction of engineer in

250 Providing and fixing approved make '90° Elbow' for

Perforated C type cable tray. Made from sheet steel. The

Junction should be bended as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS 2629/4759. with

coupler plate / Fish plate and GI hardware like nut - bolt and

washers etc. erected on existing support as per

Specification and as per instruction of engineer in charge..

(3)150 X 50 X 1.6 mm Thick 90° Elbow 5.00 ea 163.62

251 Supplying & erecting approved make motor control cubical 1.00 Ea. 13794.58

panel [Star delta] made from 16G CRCA sheet duly epoxy

powder painted inside and outside with hinged doors and

locking with suitable size of ON - OFF isolator (AC 3 /

duty) main fuses. Digital volt and current meter (in a single

unit) with micro controller based control unit and current

sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and

under voltage (Programmable) protection, prod less dry run

protection programming facility for setting of all parameter

like overload current, high voltage limit, low voltage limit, dry

run limit with digital indication on seven segment LED

display for any fault like over load, high voltage, low voltage,

dry running single crimped, electronic star delta timer,

feather touch start / stop push buttons to be erected on

angle iron frame. Grouted on wall the contactors will be of

L& T, Siemens , BCH make only). S/D up to 10 H.P.

252 Lowering of submersible motor pump set at the depth of 1.00 Job 2568.43

following ,complete with required. Nos. and size of casing

pipes erected by means of proper chain pulley block & pipe

wrenches after checking of threads of each pipe with

coupling to take the load of the pump set and pipe assembly

filled up with water .Above 60 mtrs. and Up to 120 mtrs.

253 Providing and erecting ISI marked PVC insulated PVC

Sheathed Flat flexible Submersible copper cable approved

make of following Size.

(A) 3 Core x 2.5 Sq. mm. 100.00 Mtr. 104.03

(B) 3 Core x 4 Sq. mm 30.00 Mtr. 146.45

254 Making trench in soft soil of suitable width of 90 cm deep for 900.00 Mtr. 46.46

laying cable or locating the fault all over the run and back

filling the same and making the surface as normal ground.

Item Description of Item Qty. Unit Rate In Amount in Rupees

255 Providing & laying approved make Double walled

corrugated pipes (DWC) of polyethylene(conforming to IS

14930 II )with necessary connecting accessories of same

material at required depth in existing trench for laying of

cable. below ground / road surface for enclosing cable.

(A)50 mm outer dia 580.00 Mtr. 62.62

(D)120 mm outer dia. 130.00 Mtr. 137.36

256 Providing & laying. Half R.C.C. Hume pipe for cable to be 410.00 Mtr. 263.61

laid 90 cm. below ground across the road crossing or on

floor with necessary material in an approved manner and

making the ground as per original.(E)150 mm dia

257 Supply of 250 KVA Outdoor type Compact Substation 1.00 Ea 1079011.28

consisting of Transformer,HT switchgear and LT Switchgear

and confirming to IEC-62227. a) Transformer: 250 KVA

Copper wound 11KV /433 V DYn11, Dry Cast resin type

Transformer with tapping range +10 to -10% @ 2.5% ( with

tolerance), class F , with surge restorers, Digital WTI,

IS1171 as per b) HT Compartment: 11KV, 21kA for 3 Sec .

630 A 50 Hz, gas insulated VCB in SS tank in sheet

enclosure having provision for one no. direct connection of

Incoming supply cable upto 300sq mm and one no. VCB(

Manually charging & closing) in series with LBS between

VCB and Transformer, Self Powered Relay 3 O/C +1 E/F

Relay type CSPR-V5, mechanical ON/OFF indicator, trip

coil , Manual Close & Trip PB, live cable indicator,

mechanical interlocks, pad locking facility, SF6 gas

manometer, cable boots, 3 nos. CTs with Ratio -/1A, Cl:

5P10, 2.5 VA for protection c) LV side compartment : one

no. MCCB of 400A, 36kA, 4Pole, Microprocessor based

release with arrangement for bottom cable termination

[9000 rs added in SOR Rate for 03 Nos extra outgoing

258 (A) GENERAL DESCRIPTION OF LIFTS.

[1] GEAR LESS LIFT DRIVE (MRL) comprising of High

Starting torque Lift 3 phase 440 V A. C. Permanent Magnet

Synchronous motor of proper rating with high efficiency shall

be used.[2] Micro processor based / PLC, ACVVVF, vector

control drive with encoder feedback closed loop system shall

be used for lift car and door operation which shall be full

collective selective operation hall call demand response,

UP/DOWN hall stops, Main, Up/ Down Contactor with

overload and phase reversal relay and safety controls.

[3] Car with M S platform with bracings of adequate size and

to sustain the impact load cabin + passenger with safety

factor of fire for steel and side panels of Stainless steel of

sheet of grade 304 duty. Car ceiling will be S.S. finishes with

aesthetic appearance with LED ceiling lights. Car flooring

shall be of anti skid PVC with choice of colour of engineer in

charge. Car doors shall be of stainless steel grade

hairline finish with centre opening / telescopic automatic

doors. Car panel will also be S.S. 304 finished with

emergency stop device, mechanical door safety device,

facility of auto/ attended mode. All car panel buttons and all

floor switches must be with brail language as per lift act.

Item Description of Item Qty. Unit Rate In Amount in Rupees

[4] All landing doors must be fire rated for 2 hour shall be

fully automatic centre opening/ telescopic opening made of

hairline finish steel grade of 304 with key holes and infrared

curtains with Unlocking facility from outside

[5] Appropriate battery operated emergency light in the car

along with alarm switch shall be provided. Also, Emergency

Light & Fan should start immediately without any Time Delay

as soon as power fails.

[6] Digital scrolling indicator system for up-down arrow along

with floor position indicator shall be provided inside the car

and at all floors.

[7] Full height infra red curtain with multiple cross / crossing

light beams shall be provided.[8] Automatic Rescue Device

(ARD) shall be provided accordingly of passenger capacity

with Manual Rescue Operation ( Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over loading

shall be provided such that doors kept open till excess load

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic sleep

timer shall be provided.

[12] Voice annunciator with suitable music shall be provided

[13] Self diagnostics system for operational and safety

parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and submission of

calibration certificate submission, door key holes in the floor

doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift machine

room and monkey ladder for lift pit should be provided by the

lift agency, along with the other steel structure works,

foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided without

any extra cost, where ever required as / if directed by

engineer in charge.

[17] Permanent wiring with necessary safety devices like

RCCB in all circuit, Over Voltage Under Voltage protection

and THD eliminator in circuit for lift machine room and lift

well with proper numbers of light points, with fixtures,

exhaust fan and plug points shall be provided by the agency.

Only 3 phase Power Supply shall be made available by

department in lift machine room. Necessary Earthing as per

Lift Act/Rules shall be arranged by Lift Agency.

[18] Any civil/ electrical works for additional and alteration in

lift shaft and machine room related to erection of lift shall be

made by lift agency without any extra cost. (granite/marble

fixing around all landing door openings are not in lift

agency’s scope.)

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all necessary

permission from lift inspector and other authorities. [20]

acrylic transparent licence/display A4 size holder in lift car

Item Description of Item Qty. Unit Rate In Amount in Rupees

[20A] As per statutory requirement of Govt. Of Gujarat lift &

escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection

during/after lift erection and provide report by third party

authorized by concern licensing authority 5.agency has to

provide third party insurance upto completion of free

maintenance period and submit the document for the same.

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly visible

when view from inside cabin.

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should be

provided at appropriate height on the Rear & Side Wall

Panels in Lift Car.

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for

PREMIUM category

1.Advanced control system dual 64 bit embedded

microprocessor with CANBUS Serial Communication mode

including Regenerative power efficient operation,on site

programming facility, Anti nuisance, Pte-opening, BMS/RMS

with necessary online real time monitoring system having

necessary connectivity for remote monitoring & other

suitable supporting hardware & software devices to fulfil the

2.Floor Indication LCD Display with call registration & brail

mark with arrival gong and hall lantern & TFT Screen in the

car with MP3 Voice Announcer.

3. CAR Panel should be Scratch resistive SS Moonrock

finish / Hair Line / Honeycomb for car and all Doors, All

landing doors must have fire rating up to 2 hours and car

door must have multi-level crisscross beam door protection.

8 / 10 Passengers, Ground plus 2 upper floor with Rated 1.00 ea 1474779.78

Speed of 1.0 m/sec., (C) With General PLUS ADDITIONAL

SPECIAL FEATURES attached herewith. Prem. Cat.

259 Supplying and erecting horizontal / vertical mounting type 11.00 ea 9605.10

storage water heater with copper container housed in

M.S./S.S./ABS body insulated with glass wool/puff complete

with heating elements,adjustable thermostats 300C to

850C, indicating lamp, safety valve, fusible plug,

etc.complete erected with coach bolts, nuts. washers &

cementation (C)25 Ltr. with 2 KW. heating element

Premium Category

Rupees Eight Crore Eight Lakhs Ninety-Six Thousand Five Hundred Thirty-Seven and One Paisa Ninety-Eight Only.

I/We am/are willing to carry out the work @ ______________ % ______________

percent (should be written in figures and words) below / above, the estimated rates

mentioned above, amount of my/our tender works out as under :

*Estimated amount *Estimated amount

put to tender Rs._____________________ put to tender Rs. ________________

Item Description of Item Qty. Unit Rate In Amount in Rupees

In words Rupees ____________________ In words Rupees ___________________

Signature of Contractor

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge

for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017

Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per

actual mix design the cost of difference of cement consumption have been deducted from the rate of original item at the

rate of input rate mentioned in all the tender.

5. The Contractor will have to submit the all required mix design at his own cost before execution as directed and

to be approved from the Engineer in charge.

6. Credit for dismantalled materials of amount of Rs.0.00 must be recovered from 1st R.A. bill of Contractor's.

7. Contractor has to carried out dewatering work at his own expense. If water found at any stage during

constrution, no any payment shall be given by department for dewatering work.

Above all items of "Schedule-B" with Item Description, Unit, Qty, Rate & Amount have verified by me and

Dy. Executive Engineer Executive Engineer

City Police Bldg. Sub Division City (R&B) Division

Vadodara Vadodara