Construction of Ayurvedic Dispensary 1st floor (Doctor Residence) at Kosri in Tehsil Jaisinghpur Distt. Kangra (HP)

Amount

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) or any other mixed variety of soil including shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) up to any heights / depths or any quantum of water including slush which may arise during de-watering, removal of slush and stacking the serviceable and un-serviceable material clear from the edges of excavation and then returning the stacked soil in 15cm (fifteen centimetre) layers where required into plinth and side of foundation etcetera, consolidating each deposited layer by ramming & watering and then disposing of all surplus un-serviceable excavated earth as directed within all leads and lifts, by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and disposed of material to be neatly dressed and leveled as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Foundation, footings basis of columns etcetera and mass concrete as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimeter) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimeter) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetera upto any thickness as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls up to all width and heights as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etcetera with wooden battens and ballies, in all heights of propping and centering below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing, as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement is to four sand is to eight graded crushed stone aggregate 40 mm (forty millimetre) nominal size) and curing complete excluding the cost of form work in foundation and plinth as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 (M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimetre) with cement contents not less than 330 kgs (three hundred thirty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in Foundation footings, bases of columns and the like and mass concrete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kgs (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in columns ,pillars, post, struts and the like and mass concrete up to all floor level, as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum compressive strength of 20N /mm2 (Twenty newton per square millimetre) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in suspended floor ,roofs , landings , shelves and their supports balconies, beams ,girders , bressumers and cantilevers up to all floor level as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying cement concrete work of grade M-20 ( M-twenty) design mix to obtained the minimum Compressive strength of 20N /mm2 (Twenty Newton per square millimetre) with cement contents not less than 320 kg (three hundred twenty kilogram) per cubic metre to give an even smooth surface mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work in stair case (except spiral stair cases) including landings etcetera up to floor all levels as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing Tor steel reinforcement of TATA/TISCO/SAIL for RCC work including bending, binding and placing in position complete up to all floor levels with cost of binding wire including carriage of material within all leads, lifts and other incidental and as per the direction of the Engineer-In-Charge .The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Second class brick work using common burnt clay building bricks in superstructure above plinth level to floor all levels in cement mortar 1:6 (one cement is to six sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Half brick masonry using second class common brunt clay building bricks in super structure above plinth level to floor all levels in cement mortar 1:4 (one cement is to four sand) as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing angle iron door frame (Single rebate) manufactured from M.S. angle iron section of 35x35x4mm(thirty five into thirty five into four milimetre) and M.S flat 50x4mm ( Fifty into four milimetre) as per drawing and design including hinges jamb, lock jamb, beed and if required angle threshold of mild steel angle 50x25 mm (Fifty into twenty five milimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5 mm (Two decimal five milimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals . The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing factory made PVC door frame single rebate of any clours of size 50x47mm (fifty into forty seven )with a wall thickness of 5mm made out of extruded 5mm (five millimetre) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. of 150mm (one hundred fifty millimetre) long brackets of 15mmx15mm (fifteen into fifteen millimetre) M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm (nineteen into nineteen millimetre) M.S. square tube of 19 (nineteen) gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100mm(hundred millimetre) long with wooden or rawl plugs emedded in masonry complete as per manufactures specification & direction of Engineer-in-Charge.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing to existing door frames 30mm (thirty millimetre) thick factory made wire mesh solid PVC door shutters consisting of frame made out of (Mild Steel) tube of 19 (Nineteen) gauge thickness of size 19mmx19mm (Nineteen into nineteen millimetre) for style and 15mmx15mm ( Fifteen into fifteen millimetre ) (Mild Steel) square tube for top, bottom & Lock rail (Mild Steel) frame shall have a coat of steel primer and covered with 5mm (five millimetre) thick PVC solid sheet heat moulded "C" channel of size 75mmx30mmx60mm (seventy five into thirty into sixty millimetre) out of which 10mm (ten millimetre) shall be bent at 90 (ninety) degree towards inner side on front face of the door (Mild Steel) frame at lock rail shall be covered with 100mm (one hundred millimetre))wide PVC sheet out of which 10mm (ten millimetre) on both the edges shall be bent at 90 (ninety) degree on front face of the door and 85mm (eighty five millimetre) wide PVC sheet shall cover the (Mild Steel) frame at top, bottom & lock rail of 70mm (seventy millimetre) on back side of door 5mm (five millimetre) thick 20mm (twenty millimetre) wide cross PVC sheet as gap insert for top and bottom rail, PVC sheet beading of 10mm thick, 15mm wide PVC sheet beading is to be stick internally in the back side of style and rails of door with solvent cement adhesive including fixing of G.I. wire mesh 85G or 0.56 mm (Zero point fifty six millimetres) dia wire fixed between PVC sheet of style and rail bent at 90 (ninety) degree on front face using 15mmx15mm ( fifteen into fifteen millimetre) L-shape PVC beading nailed on style a rails including fixing shutter to existing door frame with M.S. butt hinges 100x58x1.90mm (one hundred into fifty eight into one point ninety millimetre) with necessary screws etcetra complete as per specification, approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing angle iron door frame (Double rebate) manufactured from M.S. angle iron section of 40x40x4mm(forty into forty into four milimetre) and M.S flat 50x4mm ( Fifty into four milimetre) as per drawing and design including hinges jamb, lock jamb, beed and if required angle threshold of mild steel angle 50x25 mm (Fifty into twenty five milimetre) welded or rigidly fixed by mechanical means, lugs with split end tails to each jamb including steel but hinges 2.5 mm (Two decimal five milimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals . The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S. channels frames 75x40x4mm (Seventy five into Forty into four Millimetre) door/ windows/ ventilator frame and M.S. flat 75x4mm (Seventy five into Four Millimetre) combination welded together to make a one frame as per design, drawing including hinges, jambs, beads if required, threshold of M.S. angles 50x25 (fifty into twenty five millimetre) welders rigidity fixed by mechanical means, hinges with split end tails to each jambs with a provision of locking arrangements, shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of surfaces as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 25mm (twenty five millimetres) thick water proof termite resistant commercial board of Uniply / Green ply in shelves/box for cupboard with butt joints & fixing with nails & screws etc complete) as per specifications, approved drawing, design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 6 mm ( six millimetre) thick commercial ply wood lining/partition lining / partition of approved quality with butt jointing and nails including providing and fixing bottom frame 40x40(forty into forty millimetre) in 2nd class deodar wood and cover filets beading 60x12mm (sixty into twelve millimetre) section of 1st class indian teak wood in joints of partition and to be painted with white synthetic enamel paint complete as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen Millimetres) thick commercial board cupboard shutter and all cut portion of shutter shall be finished with 6/12mm (Six/twelve millimetres) thick hard wood edging including nickel plated bright finished piano hinges with screws complete, as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 40mm (forty millimeter) thick second class Deodar Wood paneled glazed or paneled and glazed shutters for doors, windows and clearstory windows including black enameled iron butt hinges, with necessary screws etcetera complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, GST, toll tax, Sale Tax or other taxes imposed by the government.

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections joints mitred and welded with 16 x3.15 mm (Sixteen into three decimal one five millimetre) iron lugs 10 cm (Ten centimetre) long embedded in cement - concrete blocks 15cm x 10cm x 10 cm (fifteen into ten into ten centimetres) size of 1:3:6 (one cement : three sand: 6 crushed stone aggregate ) 20mm (twenty millimetre) nominal size or with wooden plugs and screws rawl plugs and screws or with fixing clips or bolts and nuts as required and iron fitting including providing and fixing of glass panes with glazing clips and special metal sash putty of approved make complete including applying a priming coat of red lead paints as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

fixed steel window

Top Hung ventilater

Side hung window

Providing and fixing factory made double steel shutter windows side hinge (one glazed and other wire gauge ) of standard rolled steel section jointing mitered welded with manufactured to relevant ISI standard specification with steel plugs and screws or row/ screws or with clips or with bolts and nuts as required and iron fitting , including providing and fixing of glass pans with glazing clips and special putty of glazed side of shutter and wire gauge of ISI designation 85G with metal beading on other side complete including priming coat of red lead paint as per specification approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing anodized aluminum sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts screws etcetera complete as per specifications approved drawing, design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

300 X 16 mm (three hundred into sixteen millimetre)

250 X 16 mm (two hundred fifty into sixteen millimetres) size

Providing and fixing aluminum tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetera complete as per specifications approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

250 x 10 mm (two hundred fifty into ten millimetres) size

100 x 10 mm (one hundred into ten millimetres) size

Providing and fixing aluminum handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

125 mm (one hundred twenty five millimetre) size

100 mm (one hundred millimetre) size

Providing and fixing aluminium anodized transparent or dyed to required shade and colour hooks and eyes with necessary screws etcetera complete 150 mm (one hundred fifty millimetre) size as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 65x35mm. ((Sixty five into thirty five millimeter special quality bright finished brass cup board locks or wardrobe locks with six levers includingnecessary screwsetc. Complete including entire carriage of materials within all leads and lifts and other incidentals as per approved drawing, design and as directed by the Engineer- in-charge. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying double charge/Ultra Charge viterified tiles 600x600x10mm (six hundred into six hundred into ten) millimeter in grey / coloured of Kajaria / Asian / Johnson & Johnson manufactured approved shade in flooring treads of steps and landing on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying double charge/Ultra Charge viterified tiles 600x600x10mm (six hundred into six hundred into ten) millimeter in grey / coloured of Kajaria / Asian / Johnson & Johnson manufactured approved shade in skirting riser of steps and dados on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying acid resitant viterified tiles 300x300x10mm (three hundred into three hundred into ten) millimeter in grey / coloured of Kajaria / Asian / Johnson & Johnson manufactured approved shade in flooring treads of steps and landing on a bed of 12mm (twelve millimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

White glazed tiles 6 mm (six milimetre) thick in skirting of IS quality 30x30cm (Thirty into Thirty centimetres) of NITCO/Somany tiles or its equivalent in risers of steps and dado 12 mm( twelve millimetre) thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry to all floor level as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying 20 mm (twenty milimetre).thick Pink makrana marble work (table rubbed and polished) in flooring 10mm (Ten milimetre)thick base in cement mortar 1:3(1cement:3sand) including jointing with cement mortar 1:2(1 white cement:2 marble dust)with an admixure of pigment to match the shade of the marble complete as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing prepainted steel sheet roofing of Tata/ Dura shine/Reliance/ Jindal over steel trusses of 0.60 mm thickness (ISI marked Z-120) over steel truss prepainted galvanized steel and hot diffed metallic zinc coat sheet with top coat of regular modified polystar (RMP) organic coating of 20 micron over 5 (Five) micron and back coating of polystar 5 (five) micron over 5 (five) micron primer coating including fixing with prepainted iron jrw hooks, bolts , nuts 6 mm (six millimetre) dia with prepained limpat and rubber washers complete with all accessories as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing ridges or hips 60 cm (Sixty centimetres) over all with 0.60mm (Zero decimal Six zero millimeters) thick pre-painted Tata / Shakti sheet steel ( Factory made) shall be having proper Gola / shape with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating to back coat of polyester of 5 (Five) microns over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts 6mm (Six millimeters) diameters with pre-painted G.I. limpet and bitumen washers complete with all accessories as required as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing valley 90cm (Ninety centimetre) over all of Tata Dura shine with 0.60mm (Zero decimal Six zero millimeters) thick pre-painted steel sheet of Tata / Shakti having proper gola with hot dipped metallic Zinc coated sheet with top coat of regular modified polyester (RMP) organic coating of 20 (twenty) microns over 5 (Five) microns primer coating to back coat back coat of polyester of 5 (Five) microrns over 5 (Five) microns primer coating including fixing with pre-painted iron J or L hooks, bolts and nuts with EDPM seal. the metal sapply will be accompanied by test by certificate & 20 years warrenty from company against the corrosion fading of colour & manufacture defect as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S. ( Mild Steel) B.P. sheet 2.00 mm (two millimeter) thick in eaves boards/facia/soffits /ceiling including cutting, fixing, jointing with gas/electric welding to steel roof members and applying a coat of red lead primer complete (Base members of steel work shall be measured and laid for separately) as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 300mm. (Three hundred millimeter) wide 300mm. (Three hundred millimeter) deep clear plain G.I. Sheet gutter of Tata with brackets 40x3mm (Forty into three millimeter) size, bolts nuts and washers etc. including dome shape gratins and making necessary connections with rain water pipe complete as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 110mm (one Hundred ten milimtres) diameters on wall face P.V.C. (D-plast) rain water pipes 2.2mm ( Two decimal Two millimeter) thick of supreme/Finolex/Kisan working pressure not less than 4.50 kgs(Four decimal five zero kilograms) per square centimetre including filling the joints with approved adhesive complete as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing on wall face P.V.C. (D-plast) acessories of Supreme/Kisan/Astral for rain water pipes including filling the joints with approved adhesive complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

110mm (One hundred ten millimtres) diameteres PVC Plain bend

110mm (One hundred ten millimtres)diameteres PVC shoe

Providing and fixing 110mm (one hundred ten millimetre) diametre M. S. holder bat clamps of approved design to PVC pipes embedded in cement concrete block 10cmx10cmx10cm (Ten centimetre into Ten centimetre into Ten centimetre) of 1:2:4 (One cement is to Two Sand is to Four graded crushed stone aggregate 20mm (Twenty millimetre) nominal size including cost of cutting holes and making good the wall etcetera as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Steel work of TATA/TISCO/SAIL welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint in beams, joist, channels, angle, tee, flat with connecting plates or angle, cleats as in main and beams, hip and jack rafter fixing in rafter, purlin connects to common rafter in trusses complete as per H.P.P.W.D specification, approved drawing , design, as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint of Asian/ Nerolac brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters with enamel paint of approval shade as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

6mm (Six millimetre) thick cement plasters in ceiling with cement mortar 1:3 (One cement: Three sand) for all height above plinth level to floor two level as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimetre) thick cement plaster in single coat on rough side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (One cement is to six sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimetre) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for interior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (1 cement : 6 sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

15 mm (Fifteen millimetre) thick cement plaster in single coat on fair side of brick/concretes/ stone walls for exterior plastering up to all floor levels including arises, internal angles, chamfers and rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:5 (1 cement : 5 sand) as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering and knotting as required with ready mixed primer as per specifications, approved drawing , design or as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Finishing wall with weather proof exterior emulsion of Ultrateck/ Spetrum Nerolac/ Asian paint of approved brand and manufacture on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete as per PWD specification. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar dropping, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete. as per specifications, approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Wall painting two or more coats with acrylic emulsion paint of approved brand and manufacture (Narolac/Asian paints) and of approved shade for interior grade on undecorated concrete/ stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty as required for making the surface complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, GST, toll tax, Sale Tax or other taxes imposed by the government.

Providing and fixing of 50 mm dia (fifty millimetre) M.S. hollow pipe hand rail slip resistance with round ended at two level at 75 cm to 90 cm (seventy five centimetre to ninety centimetre) in height. It shall be 30cm (thirty centimetre) beyond the top and bottom 25mm (twenty five millimetre) dia M.S. baluster to be welded with M.S. hollow pipe and emended in cement concrete 600 mm c/c (six hundred millimetre centre to centre) with applying a coat of red lead paint as per approved drawing , design or as per the entire satsifaction and direction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing M.S.( Mild Steel) plain grills of required pattern in window frames etcetera with M.S.Flats,20x5mm ( twenty into five millimetre) and 8 x 8 mm ( eight into eight millimetre) solid square or round bars, fixing to frames with round headed bolts and nuts or by screws or welding as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying four courses water proofing treatment with bitumen felt over roofs consisting of first and third courses of blown or / and residual bitumen applied hot at 1.45 kg per sq .m of area for each course second course of roofing felt type 3 grade 1 (hessian base self finished bitumen felt) and fourth and final course of stone grit 6 mm and down size or pea sized gravel spread at 6 cu.dm or 0.006 cu.m) per sq.m. including preperation of surface excluding grading completeas per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing European sheet No 20041 of Cera / Hindware / ESSESS/Jaguar vitreous china water closet (European type with integral P or S trap including jointing the trap with soil pipe in cement motar of approved adhesive (sheet cover and jet spray to be measured and paid for separately) as per approved specification and entire satisfaction of Engineer in charge. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 100mm size sand cast iron 'P ' or ' S ' trap for water closet (squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1 (1 cement 1 sand) The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing Solid Type white plastic sheet (Solid type) and cover for washed on water closet with CP brass hinges and rubber buffers including carriage of materials within all leads, lifts and other incidental charges complete in all respect.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing PTMT low level dual flushing cistern of 10 litre capacity of Hindustan/Commander/Hindware with a pair of PVC / C.I. or M.S.bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling for connections with inlet, outlet and over flow pipes including cutting holes and making good the same ( over flow pipe to be measured and paid for separately The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing vitreous china wash basin 630mm x 450mm size Cira / Hindware / Hindustan/ Neycar No N-102012 with single hole for pillar tap with C.I. Or M.S brackets painted white including cutting holes and making good the same but excluding fittings The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameters P.V.C. waste pipe Supreme/finolex/prince waste pipe for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm nominal size diameter rubber plug for wash basin (Heavy duty ). The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 32mm diameters M.I. union for wash basin or sink Jal/Jaguar/ESSESS including necessary fittings. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing P.V.C. waste pipe Supreme/finolex/prince waste pipe for wash basin or sink including brass check nut The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 100mm diametres C.P. Grating of Jal/Jaguar /Kingsten/ Gem/Pasko (Heavy duty makes ISI marked ) for gully / floor or Nahni trap including fitting in all respect The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing of jet pressure of ESS-ESS for Europen seat with one meter tube of approved brand and manufacture, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing flat back 600x450mm beveled edge mirror or superior glass of Atul/Modi Gaurd/Golden fish mounted on 6mm thick A.C. sheet or ply wood sheet and fixed to wooden plugs with C.P. brass screws and washers etcetra complete. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing C.P.(chromium plated) brass towel rail having size 600x20 mm of Jal/Jaguar ESSESS complete withC.P. brass brackets fixed to wooden plugs with C.P. brass screws etcetra complete. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing chromium plated brass soap dish of ESS-ESS with C.P. brass brackets fixed to wooden cleats with C.P. brass screws, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) diameters C.P. brass bib tap of ESS-ESS with capstan head, within all leads, lifts of materials and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm diameter C.P.(Chromium plated) brass stop cock of Jal/Jaguar / ESSESS with fitting complete. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm dia C.P. brass pillar tap with capstan head of Jal/Jaguar / ESS ESS with fitting complete in all respect .The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 15mm nominal bore PVC connection pipe with brass union 45cm length, with necessary fittings. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing heavy quality stainless steel kitchen sink with C.I. or M.S. brackets painted white i/c cutting holes and making good the same including fitting 600 x 450 X 150mm (six hundred into four hundred fifty into one hundred fifty millimetre) including entire carriage of materials within all leads and lifts and other incidentals, as per the direction and entire satisfaction of Engineer-In-Charge.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing PVC water Storage tank (Sintex) three layer 1000 litres net capacity ISI marked with G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto any height above ground level including carriage of material with in all leads , lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing 1216 (16 mm O.D.) pipe polythene aluminum polythene (P.E.) A.E P.E composite pressure pipe U.V. stabilized with carbon block confirming to I.S. 15450-2004 Flow guard/ Kitec for water supply including clamps at one metre spacing, cutting, fixing and making good the walls etcetera; but excluding the cost of fittings (Internal work) pipes exposed on wall including filling the joints with approved adhesive complete and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and laying in trenches galvanized mild steel tubes (medium grade) tube fittings (Earth work in trenches to be measured and paid for separately) 20 mm (twenty millimeter) nominal bore as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals as per specifications approved drawing , design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Providing and fixing in trenches P.V.C. pipe of Supreme/ Finolex /Prince class “A” soil waste and ventilating pipe fixing with approved adhesive mixure complete 4.6mm (four point six millimetre) thick shall be conform to IS No. 13592-92, It should be fire resistance, chemical resistance and should be able with stand temp upto 60⁰ c all junction fitting shall conform to IS No. 14735-99 and shall be jointed to each other by a rubber ring/ push fit jointing system with a sealing ring and a rubber lubricant adhesive for PVC pipe / ventilation pipe type A within all leads, lifts and other incidentals as per approved specifications drawing, design and as directed by the Engineer- in-charge.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

75mm nominal bore/diameter

110mm nominal bore/diameter.

Providing and fixing PVC single equal branch with oval access door, insertion rubber washer 3 mm thick bolts and nuts complete including fixing with approved adhesive etc. complete.The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

75mm nominal bore/diameter

110mm nominal bore/diameter.

Testing and fitting complete including cutting and making good the wall etcetera and entire carriage of material with in all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Equal tees (1216)

Female Elbow (1216x15 mm thread)

Male thread Connector 1216x15 mm thread

Female thread Connector 1216x15 mm thread

Providing and fixing 100mm (One hundred millimeter) nominal size/diameter P.V.C. floor trap of Supreme/ prince/ Finolex ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetra complete including within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge The rate is inclusive of octroi, royality, malkana, GST and all type of other taxes imposed by the Government.

Kapil Chand