RCC Road construction and Paver Block Installation and other necessary work as per requirement inside Kankaria Lake at maninagar ward south zone

Providing and laying cement concrete 1:3:6 (1-Cement : 3-

coarse sand : 6- hand broken stone aggregates

mmnominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth (SOR BUILDING

WORKS AHMEDABAD CITY (WITHOUT GST) YEAR:-2023-

Providing and laying cement concrete 1:4:8 (1-Cement : 4-

coarse sand : 8- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth (SOR BUILDING

WORKS AHMEDABAD CITY (WITHOUT GST) YEAR:-2023-

Providing and laying cement concrete 1:5:10 (1- Cement :

5- Coarse sand : 10- hand broken stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth (SOR BUILDING

WORKS AHMEDABAD CITY (WITHOUT GST) YEAR:-2023-

Providing and laying in position Ready Mixed M-

grade concrete for reinforced cement conctere work

using cement content as per approved Design Mix

manufactured in fully automatic batching plant and

transported to site of work in transit mixer for a lead up

to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for

reinforced cement concrete work including pumping of

R.M.C. from transit mixer to site of laying, excluding the

cost of centering shuttering finishing and reinforcement

including cost of admixtures in recommended proportions

as per IS: 9103 to accelerate/ retard setting of concrete,

improve workability without impairing strength and

durability as per direction of the Engineer - in - charge.

Without Fly Ash (Min cement level as per latest IS

shall be maintained)

SOR 23-24 IT CD NO :

Providing, laying, spreading and compacting graded

stone aggregate to wet mix macadam specification

including premixing the Material with water at OMC in

mechanical mix plant carriage of mixed Material by

tipper to site, laying in uniform layers in sub- base /

base course on well prepared surface and compacting

with vibratory roller to achieve the desired density as

per Codal Provision.

a 55 Production & Supply of WMM 1975 Cum

b 55 Laying of WMM 35 Cum

Repairing damaged M.H. and rasing M.H. up to road

level incl. removing damaged brick work and repairing

by brick masonry in C.M. 1:5 and plaster in C.M. 1:3

and fixing C.I. steps and existing MH sheet cover,

removing the debris from MH and carting the same as

a 1 (A) up to 0.15 mt. (@ Two Coarse) 728.82 No.

b 1 (B) up to 0.35mt. (@ Four Coarse) 1,155.44 No.

c 1 (C) up to 0.65 mt. (@ Seven Coarse) 1,786.49 No.

Providing & Supplying ISI Standard RCC pipes (of

sulphate resisting cement) in a standard lengths of

following class & dia meter suitable for socket-spigot

type including all taxes , insurance, transporation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to departmental stores, staking etc

complete (IS 458:1989) Class NP-3, test pressure

0.7/kg/sqcm. Rate also includes supplying RCC collar

for RCC pipes including taxes, carting, loading,

unloading, etc complete. Including labour work for

lowering, laying, jointing, RCC pipes in CM 1:1 1/2

of following diameters in proper position, grade and

alignent at all as directed by engineer in charge.

inlcuding conveyance from store to site of work

labour giving hydraulic testing and all

necessary testing as per IS code (RCC pipe Horizontal cast)

a 1 300 mm internal diameter 888.37 Rmt

b 1 450 mm internal diameter 1539.32 Rmt

c 1 600 mm internal diameter 2212.85 Rmt

Providing, laying and jointing in true line and level UPVC

pipe (SCH-40) of following dia. Including fittings of

standard make as approved by Engineer-in-charge.

a 1 15mm (IT CD NO 23061) 71.93 Rmt

b 1 25 mm (IT CD NO 23062) 90.93 Rmt

c 1 40 mm (IT CD NO 23064) 146.65 Rmt

d 1 50 mm (IT CD NO 23065) 193.73 Rmt

Providing and supplying,and jointing ISI mark only

standard length stoneware pipes of following class

and diameter including excavation for laying of

pipes, insurance, transportation, freight charges,

octroi, inspection charges, loading, unloading,

conveyance to departmental stores, stacking etc.

13 compl. (IS651/1989 or its latest revision) including

labour work for lowering, laying, joiting with cement

mortar (1:1) proportion, proper postion, grade and

alignment and all level as directed by engineer in charge

including store to site of work jointing material etc

a 1 100 mm dia (IT CD NO 24001AA) 211.05 Rmt

b 1 150 mm dia (IT CD NO 24001BA) 288.23 Rmt

c 1 230 mm dia 400.54 Rmt

Providing 15mm thick cement plaster in single coat on

Rough (Similar) side of single or half brickwalls for interior

14 1 plastering upto floor two level and finished even and 174.83 SMT

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) SOR

Leveling or orientation of existing Gully Trap chamber

15 1 incl.nece.masonry in CM (1:6) and plaster in CM (1:3) etc. 71.43 No.

using old GT stone and cover etc.comp.

Constructing Bombay Pattern Type Catch Pit of size

0.60 x 0.60 depth up to 1 mt including excavation,

B.B.C.C. (1:5:10), 23 cms thick brick maso. wall in the

16 1 prop. of CM (1:6) with 40 mm thick IPS flooring in the 3110.80 No.

prop M15 at bottom and 15 mm thick cement plaster

inside the catch pit in the proportion of CM (1:3) with out

jali etc. comp. as directed.

Providing F.R.C. MH seat cover incl. carting to the work

site etc. comp. Directed.

F.R.C. Extra Heavy Duty (EHD-35) Manhole Covers &

Frames Cover :728mm ø & 100 mm thick circular cover,

35.00 MT load design,100x2mm MS flat allround, 16mm ø

plain round bar for lifting the cover

a 1 & should be fitted with plastic cups. Frame : 560 mm ø 2843.00 SET

clear opening,outer size- 888x888x175 mm. On the upper

periphery of frame 25 x 3mm wide MS flat should be well

embed in concrete to protect theedges of frame. FRC

E.H.D.-35 manhole cover & frame described as

F.R.C. Heavy Duty [HD-20] Machinehole Covers - 560 mm

b 1 ø clearopening, The dimension of frame and cover as per 1458.00 SET

mentioned in Amend No.1 to IS 12592 : 2002 table

F.R.C. Medium Duty [MD-10] Machinehole Covers -

560mm ø clear opening, The dimension of frame and

cover as per mentioned in Amend No.1 to IS 12592 :

F.R.C. Medium Duty [MD-10] Chamber Covers & Frame-

600 x 450 mm nclear opening, The dimension of frame

and cover as per mentioned in Amend No.1 to IS 12592 :

CatchPit Jali (Heavy duty) Fixing P/F FRC catch pit jali with

18 1 frame 600mm x 600mm clear opening etc. comp.. As 1167.49 No.

directed by engineer in charge.

Carting and Fixing M.H., Chamber or Catchpite Seat and

Cover in line and level to match exisisting road level in

19 1 C.C. 1:2:4 and finishing smooth, watering and protecting 746.59 No.

for 7 days etc. complete as directed. M.H. seat cover will

be supplied byA.M.C.(from any store)

Grating(Jali): 690x690x70mm square jali, 5:00 MT load

design, 70x2mm MS flat allaround,

Frame: 600x600mm clear opening, outer size-

800x800x120 mm.On the upper periphery of frame

25x3mm wide MS flat should be well embded in concrete

to protect the edges of frame.

FRC Strom Water Grating Cover (Jali) & frame described

as above. Refer Drwing

(SET Cover and frame)F.R.C Heavy Duty (HD-20)

Machinehole covers & Frames – 560 mm clear opening

,The dimension of frame and cover as per mentioned in

Amend No.1 to IS 12592:2002 table

CatchPit Jali (Heavy duty) Fixing P/F FRC catch pit jali with

20 1 frame 600mm x 600mm clear opening etc. comp.. As 1377.64 No.

directed by engineer in charge.

Repairing damaged I.C./ Raising removing damaged

brick work and repairing by brick masonry in C.M. 1:5

21 1 and plaster in C.M. 1:3 and fixing C.I. steps and removing 396.00 No.

existing chamber sheet cover, removing the debris from

chamber and carting the same as directed.

Supplying and fixing of 380 mm H x 300 mm L x 200 mm B

Kerb block for Central Verge in M-20 grade using

mm nominal size black trap aggregate of

Sevaliya/Timba or equivalent quality for pre-cast

blocks, reasonably exposed finish/ formwork, mould

with well equipped with vibratory system for kerb

stones of approved design including curing, etc.

complete, including the cost of formwork etc.

complete. The rate shall also include necessary cutting of

22 1 asphalt, fixing the Kerb stones in line and level on 5 cm 431.96 Rmt

thick sand bedding with necessary equipments and

materials. The rate shall also include the flush pointing

in CM (1:3) for all joints of the kerbstones. Filling of

zari alone the sides of the kerb stone fixed with

Bituminous concrete mixed in proper position as

directed by Engineer in change to form a portable

mixture. In any case Gravel or such type of materials

shall not be allowed for production

a) Laying on 5 cm thick Sand Bedding

Supplying and fixing of 300 mm-L x 150 mm-B x 380 mm-

H Kerb block for Footpath in M-20 grade using 20 mm

nominal size black trap aggregate of Sevaliya/Timba or

equivalent quality for pre-cast blocks, reasonably

exposed finish/ formwork , mould with well equipped

with vibratory system for kerb stones of approved design

including curing, etc. complete, including the cost of

formwork etc. complete. The rate shall also include

necessary cutting of asphalt, fixing the Kerb stones in line

and level on 5 cm thick sand bedding with necessary

equipments and materials. The rate shall also include the

flush pointing in CM (1:3) for all joints of the kerbstones.

Filling of zari alone the sides of the kerb stone fixed with

Bituminous concrete mixed in proper position as directed

by Engineer in change to form a portable mixture. In any

case Gravel or such type of materials shall not be allowed

for production.

a) Laying on 5 cm thick Sand Bedding

Pre cast concrete kerb Providing and fixing M25

Grade of concrete precast exposed / Fair finish /

texture finish kerb stones of approved make as per

approved sample of any size and any type. Kerbs

shall be fixed on the foundation prepared as per

approved design. The rate shall also include for erecting

and fixing the pieces in position for complete kerb system

with chamfered type of kerbs including necessary

24 1 accessories of kerb like radius kerb, angles and 1061.61 RMT

quadrant kerbs, droplet kerbs etc. complete as per

drawing. Kerb shall be fixed as paper joint without any

jointing material. However cement mortar shall be

provided at the backside of kerb stone joint. (Sample

must be approved) Cost of excavation, cutting , base

side filling shall includes as directed engineer - incharge in

above item description as per BOQ (a) 450 hight x 600x

150 mm high median kerb.

Pre cast concrete kerb Providing and fixing M25

Grade of concrete precast exposed / Fair finish /

texture finish kerb stones of approved make as per

approved sample of any size and any type. Kerbs

shall be fixed on the foundation prepared as per

approved design. The rate shall also include for erecting

and fixing the pieces in position for complete kerb system

with chamfered type of kerbs including necessary

25 1 accessories of kerb like radius kerbs, angles and 912.50 RMT

quadrant kerbs, droplet kerbs etc. complete as per

drawing. Kerb shall be fixed as paper joint without any

jointing material. However cement mortar shall be

provided at the backside of kerb stone joint. (Sample

must be approved) Cost of excavation, cutting , base

side filling shall includes as directed engineer - incharge

in above item description as per BOQ (b) 380 x 600 x

150 mm high Footpath kerb.

Providing and fixing pre-cast concrete kerb stone of

gray cement based concrete block 30cm length,30cm

height and 15cm thick of M200 grade concret as per

26 1 approved design and including excavation for fixing 376.43 RMT

in proper line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete. SOR 23-24 IT NO

Supplying and fixing for central verge 230 mm L x

mm Width x 680 mm H Supplying & Fixing in M-20 grade

using 20 mm nominal size black trap aggregate of

sevaliya/timba or equivalent quality for pre-cast

blocks,reasonably exposed finish/formwork,mould with

well equipped with vibratory system for kerb

stones of approved design including

curing,etc.complete,including the cost of

formwork etc.complete.THe rate shall also include

necessary cutting of asphalt,fixing the kerb stones in line

and level on 5 cm thick sand bedding with necessary

equipments and materials.The rate shall also include

the flush pointing in CM(1:3)for all joints of the

kerbstones.Filling of Zari alone the sides of the kerb

stone fixed with bituminous concrete mixed in proper

position as directed by engineer in charge to form a

portable mixture.In any case gravel or such type of

materials shall not be allowed for production.

Providing and Laying of Rubber Moulded Paver Block

Grey/Coloured 60 mm thick, M-35 Grade of any size ;

shape (Usually Uni-Paver Blocks) using black trap

good quality aggragate of 20 mm nominal size for

footpath, parking areas, service lanes and other

areas as mentioned in the drawing / instruction of

engineer in charge. Cost includes formworks using

rubber mould, Rate providing and laying paver blocks

as per required grading and specification. The paver

block shall be mechanically compacted. The work of

paving blocks shall be executed in line and level by

skill mason of flooring work only. It should be laid in such

a way that the no cutting of the paver block to be

necessary. if cutting of paver block necessary then it

should be cut by machine only and carting. The finished

surface of the paver block shall have resonably good,

plain finished. Paver blocks shall be compacted and shall

be relaid if necessary. Gravel or such type of materials

shall not be allowed for production.

Laying on 5cms thick sand beddding.

Providing and laying of interlocking grey paver blocks of

high density 80mm thick made from M-40 grade concrete

using 6 mm to 20 mm machine crushed well graded

stone aggregate, sand of approved quality, OPC 53 grade

cement with contractor's own concrete mix design as

approved by AMC, for parking, road. Cost Includes

formwork, using rubber/FRP mould, laying paver

block as per required grading and specification

laid paver block shall be mechanically compacted.

29 1 The work of the paving blocks shall be executed in line 572.00 SMT

and level by skilled mason of flooring work only. It

should be laid in such a way that the no cutting of the

paver block to be necessary. Cutting of paver block by

machine cut only and carting to be done. The

Finished surface of the Paver Block shall have reasonably

good plain finish. Paver blocks shall be compacted and

shall be re-laid if necessary. Gravel or such type of

materials shall not be allowed for production.

Laying on 5 Cms thick sand bedding.

Paver Block Providing and laying shot blasted Non -

interlocking, Paver blocks of specified thickness,

size, grade of concrete and colour machine made and

blasting by automatic shot blasting machine and high

density of as per approved sample of approved make

for footpath, parking areas, service lanes,cross over

and other areas as mentioned in the drawing.

Including providing and laying 50 mm thick averave

bedding layer of coarse sand below paver block as per

required grading and specification. Laid paver block

shall be mechanically compacted. The work of the

paving blocks shall be executed in line and level by

30 1 skilled mason of flooring work only. Small size of 669.65 SMT

paver block with same specification shall be used at

residue or at end. It should be laid in such a way that

the no cutting of the paver block to be necessary. If

cutting of paver block shall be required , than cut by

machine only and laying to be done by skilled flooring

mason. The finished surface of the paver block shall

have coarse sand Texture Finish. Pave blocks shall be

compacted and shall be re-laid if necessary. Actual laid

area shall be measured and paid without any

(A) 60 mm thick M-35 grade Grey Paver block of size

Paver Block Providing and laying shot blasted Non -

interlocking, Paver blocks of specified thickness, size,

grade of concrete and colour machine made and

blasting by automatic shot blasting machine and high

density of as per approved sample of approved make

for footpath, parking areas, service lanes,cross over

and other areas as mentioned in the drawing.

Including providing and laying 50 mm thick averave

bedding layer of coarse sand below paver block as per

required grading and specification. Laid paver block

shall be mechanically compacted. The work of the

paving blocks shall be executed in line and level by

skilled mason of flooring work only. Small size of

paver block with same specification shall be used at

residue or at end. It should be laid in such a way that

the no cutting of the paver block to be necessary. If

cutting of paver block shall be required , than cut by

machine only and laying to be done by skilled flooring

mason. The finished surface of the paver block shall

have coarse sand Texture Finish. Pave blocks shall be

compacted and shall be re-laid if necessary. Actual laid

area shall be measured and paid without any

wastage. (A) 80 mm thick M-35 grade Grey Paver

block of size 200mm x 200mm.

Labour work of fixing kurb any design of central verge,

(both side) footpath kurb, items includes necessary

excavation, asphalt cutting of any thickness, erecting in

32 100 line and position and pointing with cement mortar 136.40 RMT

(1:3), watering, etc complete, filling with zari along the

side of the kurb, the kurb stone fix prepared with

bitumnious top surface, as directed by engineer in charge.

Paver Block Providing and laying, Dished

Channel specified thickness, size, grade of concrete

and colour machine made and blasting by automatic

shot blasting machine and high density of as per

approved sample of approved make for suite drain

besides paking area and other areas as mentioned in

the drawing. Including providing and laying 50 mm

33 1 thick average bedding layer of coarse sand below 907.00 RMT

dished channel as per required grading and

specification. Laid dished channel shall be

mechanically compacted. The work of the dished

channel shall be executed in line and level by skilled

mason. Small size of dished channel with same

specification shall be used at residue or at end. If

cutting of dished channel shall be required , than cut

by machine only and laying to be done by skilled flooring

mason. Actual laid area shall be measured and paid

without any wastage. (A) 600 mm X 300 mm X 100 mm

thick M-25 grade Grey dished curved channel

MakeVYARA or Equivalent

Supply and installation of concrete bollard of size

300mm diameter x 900mm height, constructed using

34 1 M-30 concrete and 4nos 8mm dia MS Fe500 1725.00 No.

reinforcement through the section as directed by EIC

including supply of all

Construction of RCC nosing in central verge using M-200

grade cement concrete. The item includes cost of

centering & shuttering, reinforcement, both side cement

plaster in C:M 1:3 mortar & curing etc. complete. Half

round portion of the nosing shall be made by using mild

Providing, supplying and fixing precast C.C. blocks (M-20)

edge kerb having size of 75 x 300 x 300 mm depth and as

36 1 per design conveying it to the site, jointing into C:M 1:3 195.54 rmt

and racking out the joints incl. necessary excavation of

asphalt, soil etc..completed.

Supplying & Fixing Nimbhada ladi 37 to 50 mm thick for

walk way covering the activity of excavation, ramming,

37 1 laying on sand bedding as per requirement to fix the 236.60 Smt

Nibhada stone in Line & Level with cement pointing in

cement mortar 1:2 etc complete as directed.

Labour work for fixing interlocking blocks / any kind of

pavement on up to 50 mm th sand bedding, levelling,

watering and fixing in line & level as well cleaning the site

etc.comp. as directed. SOR-2016

Bitumen Cutting Labour Charges Of Cutting in bituminous

pavement.Cutting to be done with heavy duty tandom

cutting machine consist of dianond level.Minimum

Cutting Depth Shall be 75 mm From the finished

Level.Cutting Shall be perfectly in line.the width and

depth of the removal of asphalt towards kerb stone shall

be as per the drawing.bitumin Shall be Carefully Removed

39 1 so that the cutting edge towards the road should not be 127.00 Rmt

disturbed.The work of Removal of asphalt will be

considered in this item as running meter of the cutting

done by machine.one cutting line will be considered per

length of the kerb stone.Bitumen and Other Debrise shall

be disposed within 10.0 km.as per the instruction of the

engineer in charge.Surroundings Shall be cleaned to the

satisfaction of engineer in Charge

Supplying, fabricating and placing in position

reinforcement TMT bars Fe- 500, yield stress not less

than 500 N/mm2 bars confirming to IS-

reinforcement for RCC structure / items as per

design including transporting steel to the work site,

handling wastage, decoiling, cutting, bending, cranking,

fabricating to required shape, placing in position,

binding with 18 guage (1.22 mm) GI wires, welding if

necessary by using approved welding rods etc. for all

levels, all place, all height as per drawing etc.

complete as directed by the engineer-in-charge.

The quoted rate should be inclusive the cost of

binding wire, chairs, pins, brackets and the same will

not be measured and paid separately. (Rolling margin's

and wastage shall not be paid.) Measurement shall be

made on the length basis and convert into weight by

using standard co- efficient.

SOR 23-24 IT CD NO :05014C

Providing formwork of ordinary timber planking so as to

give a rough finish including centering shuttering strutting

and propping etc. Height of propping and centering below

supporting floor to ceiling not exceeding 4 M. and

removal of the same for in situ reinforced concrete and

plain concrete work in. (A) Foundations Footings Bases of

Columns etc. and Mass concrete. (SOR BUILDING WORKS

AHMEDABAD CITY (WITHOUT GST) YEAR:-2023-24)

P/A Tremix with dewartering machine and floater

machine on constructed CC work for finishing the surface

42 250 as per requirement. The rate including all machinaries, 48.21 SMT

labor, loading, unloading, transportaion etc complete as

per direction given by engineer in charge.

Making 15 mm. Groove in RCC work on road & filling it

43 83 with polysulfied selant & finished ot good incl. all labour 26.78 Rmt

charges etc. comp.as directed.

Providing & Supplying JCB Machine on rental basis in case

of emergency situation and break down type work & also

during unavoidable condition as per instruction of

engg.incharge , rate includes all nece. shifting, fuel and

operating charges and stacking of useful & non-useful

materials separately up to store. (No payment should be

allowed for non working condition of machinery and for

pipe line excavation and laying work) (SOR - (Jan. 2016)

Rates for work of Drainage / SWD pipe line - Machinery

Item No.4 Page no.7)

Hiring of Tractor with trolley considering 8 Hrs. As

45 1 working Day hours inclu. Driver (GWSSB SOR -22-23 2104.09 Day

Section 2E- Miscellenous Item no. 7)

Supplying, labour for excavation of all types of soil at any

depth including excavation of asphalt pavement of any

46 thickness,demolit ion of brick work in CM of any

proportion including stacking of serviceable materials and

disposal of unserviceable material etc. comp. as directed.

a 1 Mazdoor at day /night 452.00 No

b 1 Makadam/ supervision/Fitter at day / Night 474.00 No

Providing and suppplying Roller for compacting the road

47 1 bhuva with available building waste and Road waste 3571.43 Shift

material as and where directed by engineer in charge..

Rent for Providing Chota Hathi (Light weight vehicle) with

Driver at shown site incl. necessary oil/diesel/petrol for

vehical and all other charges.Work Done as per

Instruction of incharge etc. Complete as Directed.

The Rates are Exclusive of GST. Prevailing GST will be paid separately.

Contractor’s Quoted Rate

IN FIGURE IN WORDS

Net Quoted Tender Amount Rs.

Seal and Signature of the Bidder Additional City Engineer

mobile no. (South Zone)

AHMEDABAD MUNICIPAL CORPORATION

"South Zone Office", Opp. Fire Station, Rambaug, Maninagar, Ahmedabad - 380

Municipal Commissioner invites online Percentage Rate sealed tenders from interested contractors for the

work mentioned below.

RCC Road construction and Paver Block Installation and other

1 Name of work necessary work as per requirement inside Kankaria Lake at

maninagar ward south zone (ARC)

2 Time Limit 12Months

3 Tender Validity Period 120 days from the date of submission of the tender

Register “E2” class in PWD in Govt. R&B/CPWD/AMC or

4 Eligibility Criteria

equivalent registration with any other state Govt. Or institutions.

Estimated Cost put to

Earnest Money Deposit Rs.10,000/- Demand Draft Or Bank Guarantee in favor of Municipal

Commissioner, Ahmedabad to be submitted as prescribed in tender.

5 % of the Tender Amount in form of Bank Guarantee / Demand

7 Security Deposit Draft in favor of Municipal Commissioner, Ahmedabad to be

submitted as prescribed in tender.

Tender fees Rs.900/-Demand Draft in favor of Municipal Commissioner,

(Non refundable) Ahmedabad)

In separate sealed cover each for EMD and Tender Fees along with

Submission of EMD and

Tender as described in the invitation of tender and submitted to

Assistant Manager(South zone), South zone office, Rambaug,

Maninagar Ahmedabad.

Tenders issue date Tenders from the amc.nprocure.com website shall be downloaded

from AS PER TENDER NOTICE INVITED

As per Notice inviting Tender / Addendum / Corrigendum.The

Last date of receiving

11 tenders received after latest schedule date and time will not be

entertained under any circumstances.

As per Notice inviting Tender / Addendum / Corrigendum to

Date of Opening

12 Assistant Manager / Dy.C.E.(S/Z) office, 2nd Floor, South Zone

Office, Opp. Fire Station, Maninagar, Ahmedabad-380008

Document shall be submitted in sealed envelope systems By

Mode of sending the RPAD/Speed post/ Hand Delivery in sealed covers in Duplicate (

Tender Documents One Original & One Duplicate) duly sign & seal by contractor .

14 Terms, Condition, & All general condition of contract mentioned in tender shall be

Specification applicable.

The contractor shall be responsible to make good and remedy at this

own expenses any defect which may developed or may be noticed

before the period mentioned here under from the certified date of

15 Defect &Liability Period completion, The within 15 days of receipts of the notice. In the case

of failure on the part of the contractor, the Engineer in charge may

rectify or remove or re-execute the work at the risk & cost of the

contractor. The Engineer in charge shall be entitled to appropriate

the whole or any part of the amount of security deposit towards they

expenses, If any, incurred by him in rectification, removal or re-

execution. The defect liability period shall be as under (a) for all

works costing up to Rs. 50,000 (amount put to tender), the period

shall be three months from the certified date of completion. (b) for

all works costing more than Rs. 50,000 and up to Rs. 1 crore

(Amount put to tender) ,the period shall be six (6) month from the

certified date of completion or one monsoon , which ever letter.(c)

the major project costing more than Rs. 1 crore , the period shall be

12 months from the certified date of completion which should

include one monsoon.(d) For building works , the period specified in

(a) ,(b) & (c) above or elapse of monsoon period following certified

date of completion, whichever is letter . For the purpose of deciding

the monsoon period, the 30 September may be treated as the last

0.1% per day delay of remaining work after the completion date but

16 Compensation for Delay

not more than 10% of cost of remaining works.

Water, Electricity Contractor shall have to make his own arrangements for water and

electricity for the purpose of work at site at his own expense

Terms, Condition, & All general condition of contract of Form B1 condition of contract

Specification shall be applicable.

Deduction of Retention Retention @ 2% of the value of work done will be deducted from

19 Money from each RA each RA bill. It will be released along with release of payment of

Bill Final Bill.

Addendum/Corrigendum If any Shall be Published 48 Hrs. Price To

the Final Submission Time And Date. The Same Shall From a part

20 Addendum/Corrigendum

Of Tender And The Same As to be Attached Along With The

Tender Document.

As per Account department circular no.37, date-09/08/2018 &

21 For ESIC & EPFO Act.

Circular no.27, date-07/01/2026

As per AMC Finance Department Circular No. 38 dated 21-11-2022.

22 GST The Rates are Exclusive of GST. Prevailing GST will be paid

Conditional tenders will not be accepted. Municipal Commissioner reserves the rights to

reject any or all the tenders without assigning any reasons thereof.

Seal and Signature of the Bidder Add. City Engineer

AHMEDABAD MUNICIPAL CORPORATION

ENGINEER DEPARTMENT

TECHNICAL SPECIFICATION

Name of Work : RCC Road construction and Paver Block Installation and other necessary

work as per requirement inside Kankaria Lake at maninagar ward south

Dismantling the following including loading, unloading and disposal of unserviceable material for all

lead or as directed by Engineer-In-Charge and stacking the serviceable material and backfilling the

resulting trenches and pits complete.

a. central verge -kerb stone.

b. Dismantling tiled or stone floors laid in mortar including stacking of serviceable material

and disposal of unserviceable material with all lead and lifts.

c. Demolition & disposal of unserviceable material with all lead and lift for unreinforced

d. Demolition of brick work & stone masonry including stacking of serviceable materials and

disposal of unserviceable materials with all lead and lift (1) In cement mortar.

e. Demolition including stacking of serviceable materials and disposal of unserviceable

materials with all lead and lift. (I) R.C.C work.

The demolition shall consist of demolition of one or more parts of the structure as specified or shown in

the drawings. Demolition implies taking up or down or breaking up. This shall consist of demolishing

whole or part of work including all relevant item as specified or shown in the drawings.

The demolition shall always be planned before hand and shall be done in reverse order of the one in

which the structure was constructed. Contractor is fully responsible for proper and safe demolition.

Necessary dropping, shoring and under pinning shall be provided for the safety of the adjoining work or

property, which is to be left intact, before dismantling and demolishing is taken up and the work shall

be carried out in such a way that no damages is caused to the adjoining property.

Wherever required, temporary enclosures or partitions shall also be provide 1. Necessary precautions

shall be taken to keep the dust nuisance down as and where necessary.

Dismantling shall be commenced in a systematic manner. All materials which are likely to be damaged

by dropping from a height or demolishing roof, masonry etc. shall be carefully dismantled first. The

dismantled articles shall be properly stacked as directed.

All materials obtained from demolition shall be the property of Government unless otherwise d shall be

kept in safe custody until handed over to the Engineer-in-charge.

Any serviceable materials, obtained during dismantling or demolition shall be separated out and

stacked properly as directed, with all lead and lift. All unserviceable materials, rubbish etc. shall b

stacked as directed by the Engineer-in-charge.

On completion of work, the site shall be cleared of all debris rubbish and cleaned as directed.

Mode of measurements & payment :

Measurements of all work except hidden work shall be taken before demolition dismantling and no

allowance for increase in bulk shall be allowed. The demolition of lime concrete shall be measured

under this item. Specification for deduction for voids, openings etc. shall be on same basis as that

employed for construction of work.

All work shall be measured in decimal system as fixed in its place subject to the following limits, unless

otherwise stated hereinafter : (a) Dimensions shall be measured to the nearest 0.01 mt. (b) Area shall

be worked out to the nearest 0.01 sq. mt. (c,d,e) Cubical connection shall be worked out to the nearest

The rate shall include cost of all labour involved and tools used in demolishing and dismantling including

scaffolding. The rate shall also include the charges for separating out and stacking the serviceable

materials properly and disposing the unserviceable materials with all lead and lift. The rate also includes

for temporary storing for the safety of the portion not required to be pulled down or of adjoining

property and providing temporary enclosures or partitions where considered necessary.

The rate shall be for a unit of one cubic metre.

For Dismantling of Tiled Floor:

The relevant specifications shall be followed except the dismantling of tiled or stone floors laid on

mortars shall be done Dismantling implies carefully taking up or down or these are fixed by nail screws

bolts etc. the shall be taken out with proper tools.

Mode of measurement & Payment :

The supporting materials such as joints beams if any etc. shall be measured separately. The rate shall

include stacking the unserviceable materials as directed will lead and lift.

The rate shall be for a unit of (a) RMT (b) one sq. Meter (C) CMT(d)Cu.m(e)Cu.m

Extra rate over item of excavation of earth for excavation of asphalt pavement / RCC of thickness up

to 0.20 meter including demolishing the asphalt carpet, metal, soiling/cutting Reinforcement etc.

comp. with stacking the material as directed. (a) up to 0.20 meter thickness (By Manual)(b) 0.20 to

0.30 meter (By any type of Breaker Machine or R.C.C.Cutter machine including cost of operator, fuel,

& transportation etc complete.(c) 0.30 meter & above (By any type of Breaker Machine or

R.C.C.Cutter machine including cost of operator, fuel, & transportation etc complete.

The Item shall be carried out as per Item description and as per instruction of Engineer-in-Charge

and/or his authorized representative.

The rate includes the cost of excavation of bituminous macadam i.e. bituminous layers only like DBM,

BC etc including the labours, tools, equipment and all other incidental expenses. Non Bituminous Sub-

layer/Sub base are not considered in this item.

Work shall be carried out manually or by Machinery as per site requirements.

The mode of payment for this item shall be on Smt. Basis.

Box cutting the road surface to proper slope and camber for making a base for road work including

removing the excavated stuff and depositing on the road side slope as directed upto 200Mt.lead.

Any soil which generally yields to the application of ackaxes and shoves, phawaras rakes or any such

ordinary excavating implement or organic soil, gravel silt, sand turfloam, clay, peat etc., fall under this

Clearing the site :

The site on which the structure is to be built shall be cleared and all obstructions, loose stone, materials

and rubbish of all kind, bush, wood and trees shall be removed as directed. The materials so obtained

shall be property of the Government and be conveyed and stacked as directed. within 200 M. lead. The

roots of the trees coming in the sides shall be cut and coated with a hot asphalt.

The rate of site clearance is deemed to be included in the rate of earth work for which no extra will be

After clearing the site, the center lines will be given by the Engineer-in-charge. The contractor shall

assume full responsibility for alignment, elevation and dimension of each and all parts of the work.

Contractor shall supply laborers, materials, etc. required for setting out the reference marks and bench

marks and shall maintain them as long as required and directed.

The excavation in foundation shall be carried out in true line and level and shall have the width and

depth as shown in the drawings or as directed. The contractor shall do the necessary shoring and

shutting or providing necessary slopes to a safe angle, at his own-cost. The payment for such

precautionary measures shall be paid separately if not specified. The bottom of the excavated area

shall be 1 evened both longitudinally and transversely. as directed by removing and watering as

required. No earth filling will be allowed for bringing it to level, if mistake or any other reason

excavation is made. deeper or wider that shown on the plan or directed. The extra depth or width shall

be made up with concrete of same proportion as specified for the foundation concrete at the cost of

the contractor. The excavation up to 1.5 m. depth shall be measured under this item.

Disposal of the excavated stud :

The excavated stuff of the selected type shall be used in filling the trenches and plinth or leveling the

ground in layer including ramming and watering etc. The balance of the excavated quantity shall be

removed by the contractor from the site of work to a place as directed with lead upto 200 M. and all lift.

Mode of measurement and payment :

The measurement of excavation in trenches for foundation shall be made according to the sections of

trenches shown on the drawing or as per sections given by the Engineer-in-charge. No payment shall be

made for surplus excavation made in excess of above requirements or due to slopping and sloping back

as found necessary on account of conditions of soil , and requirements of safety.

The rate shall be for a unit of one cubic meter.

Conveyance charge of earth, lime, murrum, building rubbish, manure, garbage, sludge, excavated

rock, fly ash, aggregates of any kind Including spreading & levelling etc. complete.

• (a)Lead Upto 1 Km.

• (b)Lead From 1 Km to 2 Km.

• (c)Lead From 2 Km to 3 Km

• (d)Lead From 3 Km to 4 Km

• (e)Lead From 4 Km to 5 Km

• (f)Lead From 5 Km to 10 Km

• (g)Lead From 10 Km to 15 Km

Disposal of earth, lime, murrum, building rubbish, manure, garbage, sludge, excavated rock, fly

ash, aggregates of any kind is subject to the following :

Unsuitable materials obtained from clearing site and excavation shall be disposed off within a lead of

200 meters or as per instruction given by Engineer in charge. Useful materials obtained from clearing

site and excavation shall be stacked and used within the work site. Internal conveyance above

mt within the work site i.e. From starting chainage to End chainage of a given road WILL NOT BE

PAYABLE. Materials suitable for construction of Embankment, earthen shoulder and subgrade shall

be stacked at convenient places within a work site for reuse. No extra payment will be paid to the

contractor for stacking of earth within the work site and reused for the construction of Embankment

layer, sub grade and earthen shoulder purpose. Only surplus earth shall be disposed off outside the

work site as per instruction given by Engineer-In-charge. Useful stones from rock excavation shall be

stacked nearly within a lead of 50 M. and will be allowed to be used by the contractor on payment

at rates laid down in the contract or if not so aid down, at schedule of rates of the Division or at a

mutually agreed rates if there are no such rates in the Schedule of rates.

If surplus materials are required to be conveyed outside the work site i.e. Outside conveyance from a

particular stretch of given road will be paid in this item as per instruction of Engineer in charge. No

bulkage of disposed earth will be considered for the payment.

The rate shall be for a unit of one cubic metre.

Providing and laying cement concrete 1:3:6 (1-Cement : 3- coarse sand : 6- hand broken stone

aggregates 40 mmnominal size) and curing complete excluding cost of formwork in (A) Foundation

Before starting the concrete the bed of the foundations trenches shall be cleared of all loose materials

and watered and rammed as directed. The proportion of cement, sand and hand broken stone

aggregates shall be one part of cement, 3 parts of coarse sand, 6 parts of hand broken stone aggregates

and shall so measured by volume. The concrete shall be mixed in a mechanical mixer at the site of work.

Hand mixing may however be allowed for smaller quantity of work if approved by the Engineer-

incharge. When hand mixing is permitted by the Engineer-in charge in case of breakdown of

machinery’s and in the interest of the work. it shall be carried out on a water tight platform and care

shall be taken to ensure that mixing is continued until the mass is uniform in colour and consistency.

The quantity of water shall be sufficient to produce a dense concrete of required workability for the

purpose. The concrete shall be handled from the place of mixing to the final position in not more than

15 minutes by the method as directed and shall be placed into its final position, compacted and finished

within 30 minutes of mixing with water i.e. before the setting commences. The concrete shall be laid in

layers of 15 cms. to 20 cms. The concrete shall be rammed with heavy iron rammers and rapidly to get

the required compaction and to allow all the gaps to be filled with mortar. After the final set, the

concrete shall be kept continuously wet, if required by pounding for a period of not less than 7 days

from the date of placement The concrete shall be measured for its length breadth and depth, limiting

dimensions to those specified on plan or as directed.

Mode of measurements shall be on CMT basis

Providing and laying cement concrete 1:4:8 (1-Cement : 4- coarse sand : 8- hand broken stone

aggregates 40 mm nominal size) and curing complete excluding cost of formwork in (A) Foundation

Before starting the concrete the bed of the foundations trenches shall be cleared of all loose materials

and watered and rammed as directed. The proportion of cement, sand and hand broken stone

aggregates shall be one part of cement, 4 parts of coarse sand, 8 parts of hand broken stone aggregates

and shall so measured by volume. The concrete shall be mixed in a mechanical mixer at the site of work.

Hand mixing may however be allowed for smaller quantity of work if approved by the Engineer-

incharge. When hand mixing is permitted by the Engineer-in charge in case of breakdown of

machinery’s and in the interest of the work. it shall be carried out on a water tight platform and care

shall be taken to ensure that mixing is continued until the mass is uniform in colour and consistency.

The quantity of water shall be sufficient to produce a dense concrete of required workability for the

purpose. The concrete shall be handled from the place of mixing to the final position in not more than

15 minutes by the method as directed and shall be placed into its final position, compacted and finished

within 30 minutes of mixing with water i.e. before the setting commences. The concrete shall be laid in

layers of 15 cms. to 20 cms. The concrete shall be rammed with heavy iron rammers and rapidly to get

the required compaction and to allow all the gaps to be filled with mortar. After the final set, the

concrete shall be kept continuously wet, if required by pounding for a period of not less than 7 days

from the date of placement The concrete shall be measured for its length breadth and depth, limiting

dimensions to those specified on plan or as directed.

Mode of measurements shall be on CMT basis

Providing and laying cement concrete 1:5:10 (1- Cement : 5- Coarse sand : 10- hand broken stone

aggregates 40 mm nominal size) and curing complete excluding cost of formwork in (A) Foundation

Before starting the concrete the bed of the foundations trenches shall be cleared of all loose materials

and watered and rammed as directed. The proportion of cement, sand and hand broken stone

aggregates shall be one part of cement, 5 parts of coarse sand, 10 parts of hand broken stone

aggregates and shall so measured by volume. The concrete shall be mixed in a mechanical mixer at the

site of work. Hand mixing may however be allowed for smaller quantity of work if approved by the

Engineer-incharge. When hand mixing is permitted by the Engineer-in charge in case of breakdown of

machinery’s and in the interest of the work. it shall be carried out on a water tight platform and care

shall be taken to ensure that mixing is continued until the mass is uniform in colour and consistency.

The quantity of water shall be sufficient to produce a dense concrete of required workability for the

purpose. The concrete shall be handled from the place of mixing to the final position in not more than

15 minutes by the method as directed and shall be placed into its final position, compacted and finished

within 30 minutes of mixing with water i.e. before the setting commences. The concrete shall be laid in

layers of 15 cms. to 20 cms. The concrete shall be rammed with heavy iron rammers and rapidly to get

the required compaction and to allow all the gaps to be filled with mortar. After the final set, the

concrete shall be kept continuously wet, if required by pounding for a period of not less than 7 days

from the date of placement The concrete shall be measured for its length breadth and depth, limiting

dimensions to those specified on plan or as directed.

Mode of measurements shall be on CMT basis

Providing and laying in position Ready Mixed M-200 grade concrete for reinforced

cement conctere work, using cement content as per approved Design Mix manufactured

in fully automatic batching plant and transported to site of work intransit mixer for a lead

up to 10 kms having continuous agitated mixer, manufactured as per mix design of specified

grade for reinforced cement concrete work including pumping of R.M.C. from transit mixer

to site of laying, excluding the cost of centering shuttering finishing and reinforcement

including cost of admixtures in recommended proportions as per IS:9103 to accelerate/

retard setting of concrete, improve work ability without impairing strength and durability as

per direction of theEngineer-in-charge. Without Fly Ash (Min cement level as per latest IS456 shall

be maintained) (Cement level 400 kg ) (R&B SOR 21-22 Item code 5055)

Water shall conform to M-1.

Cement shall conform to M-3.

Sand shall conform to M-6.

Coarse Aggregate

Coarse Aggregate shall conform to M-12.

CPWD specifications of item no. 5.4.1, 5.4.2, 5.4.3, 5.4.4, 5.4.5, 5.4.6 shall be followed. The relevant

specifications of item no. 2.08 and 2.01 shall be followed.

Before quoting the rate, contractor shall confirm the exposure condition for the design of concrete.

Mix design shall be carried out for environmental exposure condition as given in IS 456:2000 page 18 table

All concrete work shall have fair finish concrete surface unless otherwise specified.

For exposed concrete element specified in the drawing fair finish steel shuttering made out of MS

sheet not less than 14 gauge/ laminated plywood and supporting frame work shall be of steel. Proper

care shall be taken in MS shuttering at the time of concreting during monsoon to achieve rust free

concrete surface. The concrete surface shall be rendered if required to give fair finish.

For other concrete shuttering material shall be as follows:

 Columns: Moulds from marine ply with wooden battens or MS steel plates

 Straight walls / Curved wall in plan: Marine plywood with wooden battens of Acro make or

equivalent make plates and soldiers.

 Beam: Bottom - timber / steel plates, Sides - Steel plates / marine ply with battens

The concrete shall be designed as per relevant IS code- IS 10262 and SP 23, with or without chemical

admixture to provide the grade of concrete having required workability and characteristicstrength as per

IS 456:2000. The proportion of cement, sand and coarse aggregates shall be determined by weight. The

weight batch machine shall be used for maintaining proper control over the proportion of aggregates as

per mix design. The design mix shall be got approved by Engineer in-charge before starting the concrete

work. The minimum cement content shall depend on the exposure condition of the concrete. The

minimum cement content given in table (IS 456:2000, table 5) shall be adopted irrespective of whether

the contractor achieves the desired strength with less quantity of cement. The strength requirements of

different grades of concrete shall be as under :

Grade of Compressive strength of 15 cm. cubes in N/mm

Concrete at 7 and 28 days conducted in accordance with IS : 516-1959.

At 7 days At 28 days Max size of agg. In mm

In cases, the 28 compressive strength specified in above table be the

all days criteria for

acceptance or rejection of the concrete.

Where the strength of a concrete mix as indicated by tests, lies in between the strength of any two

grades specified in the above table, such concrete shall be classified in for all purposes as concrete

belonging to the lower of the two grades between which its strength lies.

The Contractor shall take necessary care to avoid sand streaks, air holes, honey combining etc., on

finished concrete surface.

The proportions for ingredients chosen shall be such that concrete has adequate workability for

conditions prevailing on the work and the supply of properly graded aggregate of uniform quality can be

maintained till the completion of work. Grading of aggregate shall be controlled by obtaining the coarse

aggregate, in different sizes and blending them in the right proportions as required. Aggregate of

different sizes shall be stocked in separate stock piles. The required quantity of material shall be stock

piled several hours, preferably a day before use. The grading of coarse and fine aggregate shall be

checked as frequently as possible, the frequency for a given job being determined by the Engineer-in-

charge to ensure that the suppliers are maintaining the uniform grading, as approved for samples used

in the preliminary tests.

In proportioning concrete, the quantity of both cement and aggregate shall be determined by

weight. Where the weight of cement is determined by accepting the maker's weight per bag a

reasonable number of bags shall be weighed separately, to check the net weight, where cement is

weighed from bulk stocks at site and not by bags. It shall be weighed separately from the aggregates.

Water shall either be measured by volume in calibrated tanks or weighed. All measuring equipment

shall be maintained in clean and serviceable condition. Their accuracy shall be periodically checked and

calibrated in standard laboratory.It is most important to keep the specified water cement ratio constant

and at its correct value. Moisture content in both fine and coarse aggregates shall be determined by the

engineer-in- charge according to the weather conditions. The amount of mixing water shall then be

adjusted tocompensate for variations in the moisture content. For the determination of moisture content

in the aggregates IS : 2386 (Part III) shall be referred. Suitable adjustments shall also be made in the

weights of aggregates due to variation in their moisture content.

The minimum cement content for the various mixes shall be as per IS: 456-2000.

All RCC works shall be carried out as per the detailed drawings and direction of Architects and

Engineer-in-charge. The concrete shall be placed at all heights, levels and for all shapes.

Mode of Measurement and Payment

The relevant specifications of item no. 5.4.11.1, 5.4.11.4, 5.4.11.5, 5.4.12, 5.4.13 shall be followed.The

rate shall be included or exclude the cost of centering and shuttering will be as specified in theitem.

The rate shall be inclusive of chemical admixture like plasticizer etc. as directed by the engineer-in-

charge. No extra payment shall be paid for.

The rate shall be for a unit of one cum. The cost of formwork shall be included as excluded as per

the item description.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam

specification including premixing the Material with water at OMC in mechanical mix plant carriage of

mixed Material by tipper to site, laying in uniform layers in sub- base / base course on well prepared

surface and compacting with vibratory roller to achieve the desired density as per Codal Provision.

Production & Supply of WMM

This work shall consist of laying and compacting clean, crushed, graded aggregate and granular

material, premixed with water, to a dense mass on a prepared sub-grade/sub- base/ base or existing

pavement as the case may be in accordance with the requirements of these Specifications. The material

shall be laid in one or more layers as necessary to lines, grades and cross-sections shown on the

approved drawings or as directed by the Engineer.

The thickness of a single compacted Wet Mix Macadam layer shall not be less than 75 mm. When

vibrating or other approved types of compacting equipment are used, the compacted depth of a single

layer of the sub-base course may be upto 200 mm with the approval of the Engineer.

Materials Aggregates

Physical Requirements

Coarse aggregates shall be crushed stone. If crushed gravel/shingle is used, not less than 90 percent by

weight of the gravel/shingle pieces retained on 4.75 mm sieve shall have at least two fractured faces.

The aggregates shall conform to the physical requirements set forth in Table.

If the water absorption value of the coarse aggregate is greater than 2 percent, the soundness test shall

be carried out on the material delivered to site as per IS:2386 (Part-5).

Table : Physical Requirements of Coarse Aggregates for Wet Mix Macadam for Sub-base/Base Courses

S.NO Test Test Method Requirements

Los Angeles Abrasion valueor IS:2386 (Part-4) IS:2386 40 percent (Max.)

(Part-4) orIS:5640

1) Aggregate Impact value 30 percent (Max.)

2) Combined Flakiness and IS:2386(Part-1) 35 percent (Max.)*

Elongationindices (Total)

* To determine this combined proportion, the flaky stone from a representative sample should

first be separated out. Flakiness index is weight of flaky stone metal divided by weight of stone sample.

Only the elongated particles be separated out from the remaining (non-flaky) stone metal. Elongation

index is weight of elongated particles divided by total non-flaky particles. The values of flakiness index

and elongation index so found are added up.

9.1.2 Grading Requirements

The aggregates shall conform to the grading given in Table.

Table: Grading Requirements of Aggregates for Wet Mix Macadam

IS Sieve Designation Percent by weight passing the IS Sieve

600.00 micron 8-22

75.00 micron 0-5

Material finer than 425 micron shall have Plasticity Index (PI) not exceeding

The final gradation approved within these limits shall be graded from coarse to fine and shall not

varyfrom the low limit on one sieve to the high limit on the adjacent sieve or vice versa.

Construction OperationsPreparation of Base

Clause 404.3.1 shall apply.

Provision of Lateral Confinement of Aggregates

While constructing wet mix macadam, arrangement shall be made for the lateral confinement of wet

mix. This shall be done by laying materials in adjoining shoulders along with that of wet mix macadam

layer and following the sequence of operations described in Clause 404.3.3.

Preparation of Mix

Wet Mix Macadam shall be prepared in an approved mixing plant of suitable capacity having provision

for controlled addition of water and forced/ positive mixing arrangement like pugmill or pan type mixer

of concrete batching plant. The plant shall have following features:

i) For feeding aggregates- three/ four bin feeders with variable speed motor

ii) Vibrating screen for removal of oversize aggregates

iii) Conveyor Belt

iv) Controlled system for addition of water

v) Forced/positive mixing arrangement like pug-mill or pan type mixer

vi) Centralized control panel for sequential operation of various devices and precise process control

vii) Safety devices

Optimum moisture for mixing shall be determined in accordance with IS:2720 (Part-8) after replacing

the aggregate fraction retained on 22.4 mm sieve with material of 4.75 mm to 22.4 mm size. While

adding water, due allowance should be made for evaporation losses. However, at the time of

compaction, water in the wet mix should not vary from the optimum value by more than agreed limits.

The mixed material should be uniformly wet and no segregation should be permitted.

Spreading of Mix

Immediately after mixing, the aggregates shall be spread uniformly and evenly upon the prepared sub-

grade/sub-base/base in required quantities. In no case shall these be dumped in heaps directly on the

area where these are to be laid nor shall their hauling over a partly completed stretch be permitted.

The mix may be spread by a paver finisher. The paver finisher shall be self-propelled of adequate

capacity with following features:

i) Loading hoppers and suitable distribution system, so as to provide a smooth uninterrupted

material flow for different layer thicknesses from the tipper to the screed.

ii) Hydraulically operated telescopic screed for paving width up to to 8.5 mand fixed screed beyond

this. The screed shall have tamping and vibrating arrangement for initial compaction of the

layer.Automatic levelling control system with electronic sensing device to maintain mat thickness and

cross slope of mat during laying procedure.

In exceptional cases where it is not possible for the paver to be utilized, mechanical means like motor

grader may be used with the prior approval of the Engineer. The motor grader shall be capable of

spreading the material uniformly all over the surface.

The surface of the aggregate shall be carefully checked with templates and all high or low spots

remedied by removing or adding aggregate as may be required. The layer may be tested by depth

blocks during construction. No segregation of larger and fine particles should be allowed. The

aggregates as spread should be of uniform gradation with no pockets of fine materials.

The Engineer may permit manual mixing and /or laying of wet mix macadam where small quantity of

wet mix macadam is to be executed. Manual mixing/laying in inaccessible/ remote locations and in

situations where use of machinery is not feasible can also be permitted. Where manual mixing/laying is

intended tobe used, the same shall be done with the approval of the Engineer.

After the mix has been laid to the required thickness, grade and cross fall/camber the same shall be

uniformly compacted to the full depth with suitable roller. If the thickness of single compacted layer

does not exceed 100 mm, a smooth wheel roller of 80 to 100kN weight may be used. For a compacted

single layer up to 200 mm, the compaction shall be done with the help of vibratory roller of minimum

static weight of 80 to 100 kN with an arrangement for adjusting the frequency and amplitude. An

appropriate frequency and amplitude may be selected. The speed of the roller shall not exceed 5 km/h.

In portions having unidirectional cross fall/super elevation, rolling shall commence from the lower edge

and progress gradually towards the upper edge. Thereafter, roller should progress parallel to the center

line of the road, uniformly over-lapping each preceding track by at least one-third width until the entire

surface has been rolled. Alternate trips of the roller shall be terminated in stops at least 1 m away from

any preceding stop.

In portions in camber, rolling should begin at the edge with the roller running forward and backward

until the edges have been firmly compacted. The roller shall then progress gradually towards the centre

parallel to the centre line of the road uniformly overlapping each of the preceding track by at least one-

third width until the entire surface has been rolled.

Any displacement occurring as a result of reversing of the direction of a roller or from any other cause

shall be corrected at once as specified and/or removed and made good.

Along forms, kerbs, walls or other places not accessible to the roller, the mixture shall be thoroughly

compacted with mechanical tampers or a plate compactor. Skin patching of an area without

scarifyingthe surface to permit proper bonding of the added material shall not be permitted.

Rolling should not be done when the sub-grade is soft or yielding or when it causes a wavelike motion in

the sub-base/base course or sub-grade. If irregularities develop during rolling which exceed 12 mm

when tested with a 3 m straight edge, the surface should be loosened and premixed material added or

removed as required before rolling again so as to achieve a uniform surface conforming to the desired

grade and cross fall. In no case shall the use of unmixed material be permitted to make up the

Rolling shall be continued till the density achieved is at least 98 percent of the maximum dry density for

the material as determined by the method outlined in IS:2720 (Part-8).

After completion, the surface of any finished layer shall be well-closed, free from movement under

compaction equipment or any compaction planes, ridges, cracks and loose material. All loose,

segregated or otherwise defective areas shall be made good to the full thickness of the layer and re

Setting and Drying

After final compaction of wet mix macadam course, the road shall be allowed to dry for 24 hours.

Opening to Traffic

No vehicular traffic shall be allowed on the finished wet mix macadam surface. Construction equipment

may be allowed with the approval of the Engineer.

Surface Finish and Quality Control of WorkSurface Evenness

The surface finish of construction shall conform to the requirements of Clause

Quality Control

Control on the quality of materials and works shall be exercised by the Engineer in accordance with

Rectification of Surface Irregularity

Where the surface irregularity of the wet mix macadam course exceeds the permissible tolerances or

where the course is otherwise defective due to sub-grade soil getting mixed with the aggregates, the

full thickness of the layer shall be scarified over the affected area, re-shaped with added premixed

material or removed and replaced with fresh premixed material as applicable and re compacted in

accordance with Clause 406.3. The area treated in the aforesaid manner shall not be less than 5 m long

and 2 m wide. In no case shall depressions be filled up with unmixed and ungraded material or fines.

Arrangement for Traffic

During the period of construction, arrangements for traffic shall be done as per Clause

Measurements for Payment

Wet mix macadam shall be measured as finished work in position in cubic metres.

The Contract unit rate for wet mix macadam shall be payment in full for carrying out the required

operations including full compensation for all components listed in Clause 401.7.

The Measurement of the item shall be in Cum basis.

Repairing damaged M.H. and raising M.H. up to road level incl. removing damaged brick work and

repairing by brick masonry in C.M. 1:5 and plaster in C.M. 1:3 and fixing C.I. steps and existing MH

sheet cover, removing the debris from MH and carting the same as directed.(a)upto 0.15mt.(@Two

coarse)(b)upto to 0.35mt.(@Four coarse (c)upto 0.65 mt.(@seven Coarse) (d)upto 0.90mt.(@Ten

This item relates to repairing work of above item of machine hole with fixing existing seat at top & fixing

pre-cast FRC cover (medium duty) repairing up to 2.00 mt. depth. This item relates to repairing existing

machine hole of 1.40 x 1.00 or 1.00 x 0.75 mt. size with removing first existing seat & cover including

demolishing existing loose masonry work up to from GF level to depth if specified & up to same height

brick work in CM 1:5 shall be completed & after of that work plastering work in CM 1:3 shall also be

done. Rate including fixing existing or new (if not there) C.I. steps shall fixed at time of masonary work.

After completion of brick work & plastering same machine hole seat & cover fixing at top & casted it in

C.C. 1:2:4 etc. Measurements shall be given on no. of basis up to 2.00 mt. depth work.

For detailed specification refer R & B Department booklet for General Technical Specification

for building works.

Items also includes:

1. Proper Barricading to avoid accidents.

2. Removal of debris from site.

3. Compaction of Bitumen by Roller.

4. Applying tack coat before laying of Hotmix material.

The mode of payment for this item shall be on No. Basis.

Providing & Supplying ISI Standard RCC pipes (of sulphate resisting cement) in a standard lengths of

following class &dia meter suitable for socket-spigot type including all taxes , insurance,

transporation, freight charges, octroi, inspection charges, loading, unloading, conveyance to

departmental stores, staking etc complete (IS 458:1989) Class NP-3, test pressure 0.7/kg/sqcm. Rate

also includes supplying RCC collar for RCC pipes including taxes, carting, loading, unloading, etc

complete. Including labour work for lowering, laying, jointing, RCC pipes in CM 1:1 1/2 of following

diameters in proper position, grade and alignent at all as directed by engineer in charge. inlcuding

conveyance from store to site of work labour giving hydraulic testing and all necessary testing as per

IS code .(GWSSB SOR-2022-23, page no:15, Item no:10.2.A & 10.3 & section part 1&2 B labour section,

item no:11.B) (RCC pipe Horizontal cast) (a)300 mm internal diameter (b) 450 mm internal diameter

(c)600 mm internal diameter.

For relevant Specification of Item as per item description & instruction of Engineer-in-Charge and/or his

authorized representative.

The mode of payment for this item shall be on RMT. Basis.

Providing, laying and jointing in true line and level UPVC pipe (SCH-40) of following dia. Including

fittings of standard make as approved by Engineer-in-charge.

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of work is applicable.

The measurements shall be on RMT basis.

Providing and supplying, lowering, laying and jointing ISI mark only standard length stoneware pipes

of following class and diameter including all taxes (excluding GST), insurance, transportation, freight

charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking

etc. compl. (IS651/1989 or its latest revision) Class AA (a) 100 mm dia (b) 150 mm dia (c) 250 mm dia.

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of work is applicable.

The measurements shall be on RMT basis.

Providing15mm thick cement plaster in single coat on Rough (Similar) side of single or half brickwalls

for interior plastering upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1-

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of making plastering is applicable.

The measurements shall be on SMT basis.

Leveling or orientation of existing gully trap chamber incl.nece. masonry in CM (1:6) and plaster in CM

(1:3) etc. using old GT stone and cover etc.comp..

Leveling or orientation of existing gully trap chamber incl.nece. masonry in CM (1:6) and plaster in CM

(1:3) etc. using old GT stone and cover etc.comp.

Constructing Bombay Pattern Type Catch Pit of size 600 mm x 600 mm & depth up to 1000 mm

including excavation, B.B.C.C. (1:5:10), 23 cms thick brick masonry wall in the prop. of CM (1:6) with

40 mm thick IPS flooring in the prop M15 at bottom and 15 mm thick cement plaster inside the catch

pit in the proportion of CM (1:3) without jali etc. comp. as directed by E.I.C.

600mm x 600mm x 1000mm Depth

For detailed specification refer clause No. 24.44.1 of R & B Department booklet for General Technical

Specification for building works

• Extra Depth of Catch pit size 600mm x 600mm for every additional depth of 100 mm or

Part thereof beyond 1000mm depth upto 1500 mm depth

For detailed specification refer clause No.24.46 of R & B Department booklet for General Technical

Specification for building works.

Mode of measurement and payment

The contractor shall be responsible for any loss or damage to the catch pit up to the end of work. He

shall also be responsible for the cleaning all bituminous material from the catch pit.

The rate shall be for a unit of one No.

Providing F.R.C. MH seat cover incl. carting to the work site etc. comp. Directed.

A- F.R.C. Extra Heavy Duty (EHD-35) Manhole Covers & Frames Cover :728mm ø & 100 mm thick

circular cover, 35.00 MT load design,100x2mm MS flat allround, 16mm ø plain round bar for

lifting the cover & should be fitted with plastic cups. Frame : 560 mm ø clear opening,outer

size- 888x888x175 mm. On the upper periphery of frame 25 x 3mm wide MS flat should be

well embed in concrete to protect theedges of frame. FRC E.H.D.-35 manhole cover & frame

B- F.R.C. Heavy Duty [HD-20] Machinehole Covers - 560 mm ø clearopening, The dimension of

frame and cover as per mentioned in Amend No.1 to IS 12592 : 2002 table

C- F.R.C. Medium Duty [MD-10] Machinehole Covers - 560mm ø clear opening, The dimension of

frame and cover as per mentioned in Amend No.1 to IS 12592 : 2002 table 1..

D- F.R.C. Medium Duty [MD-10] Chamber Covers & Frame- 600 x 450 mm nclear opening, The

dimension of frame and cover as per mentioned in Amend No.1 to IS 12592 : 2002 table

The rate shall be for a unit No.

Catch Pit Jali Fixing P/F FRC catch pit jali with frame 600mm x 600mm clear opening etc. comp.. As

directed by Engineer-in-Charge and/or his authorized representative.

For detailed specification refer clause No. 24.35 of R & B Department booklet forGeneral Technical

Specification for building works.

The contractor shall be responsible for any loss or damage to the catch pit up to the end of work. He

shall also be responsible for the cleaning all bituminous material from the catch pit.

The rate shall be for a unit of one No.

Carting and Fixing M.H., Chamber or Catchpite Seat and Cover in line and level to match exisisting

road level in C.C. 1:2:4 and finishing smooth, watering and protecting for 7 days etc. complete as

directed. M.H. seat cover will be supplied byA.M.C.(from any store)

A- Grating(Jali): 690x690x70mm square jali, 5:00 MT load design, 70x2mm MS flat allaround,

B- Frame: 600x600mm clear opening, outer size-800x800x120 mm.On the upper periphery of frame

25x3mm wide MS flat should be well embded in concrete to protect the edges of frame.

C- FRC Strom Water Grating Cover (Jali) & frame described as above. Refer Drwing

C- (SET Cover and frame)F.R.C Heavy Duty (HD-20) Machinehole covers & Frames – 560 mm clear

opening ,The dimension of frame and cover as per mentioned in Amend No.1 to IS 12592:2002

The mode of measurnment shall be on No basis.

Catch Pit Jali Fixing P/F FRC catch pit jali with frame 600mm x 600mm clear opening etc. comp.. As

directed by Engineer-in-Charge and/or his authorized representative.

For detailed specification refer clause No. 24.35 of R & B Department booklet forGeneral Technical

Specification for building works.

The contractor shall be responsible for any loss or damage to the catch pit up to the end of work. He

shall also be responsible for the cleaning all bituminous material from the catch pit.

The rate shall be for a unit of one No.

Repairing damaged I.C./ Raising removing damaged brick work and repairing by brick masonry in C.M.

1:5 and plaster in C.M. 1:3 and fixing C.I. steps and removing existing chamber sheet cover, removing

the debris from chamber and carting the same as directed.

Relevant specification shall be followed as per item description : Repairing damaged I.C./ Raising

removing damaged brick work and repairing by brick masonry in C.M. 1:5 and plaster in C.M. 1:3 and

fixing C.I. steps and existing chamber sheet cover, removing the debris from chamber and carting the

same as directed.

The measurement shall be in Nos. basis of I.C.

Supplying and fixing of 380 mm H x 300 mm L x 200 mm B Kerb block for Central Verge in M-20 grade

using 20 mm nominal size black trap aggregate of Sevaliya/Timba/Ankodiya/Othwad or equivalent

quality for pre-cast blocks, reasonably exposed finish/ formwork, mould with well equipped with

vibratory system for kerb stones of approved design including curing, etc. complete, including the

cost of formwork etc. complete. The rate shall also include necessary cutting of asphalt, fixing the

Kerb stones in line and level on 5 cm thick sand bedding with necessary equipments and materials.

The rate shall also include the flush pointing in CM (1:3) for all joints of the kerb stones. Filling of zari

alone the sides of the kerb stone fixed with Bituminous concrete mixed in proper position as directed

by Engineer in change to form a portable mixture. In any case Gravel or such type of materials shall

not be allowed for production.

The specifiction of following materials shall be conforming with specification mentioned for relavent

material / items in General technical specification for building work of R&B Department of Gujarat.

Water shall conform to M-1

Graded stone aggregate 20 mm. nominal size to M-10

Contractor shall have to manufacture the blocks as per the dimensions given in the drawing. Specific

machineries shall be used to manufacture the precast blocks. These machineries should be compatible

to produce blocks of required strength and dimensions. The machine shall contain hydraulic Press or

advanced equipment to generate required compaction & Grade and finish. Moulds/ Steel Plates/ Dies of

the machine shall be dimensionally checked & to be got approved before commencing the production.

Contractor shall prepare proper Drying Yard for keeping the blocks before curing. The drying yard shall

be levelled and covered so that no shrinkage cracks are formed. Contractor shall prepare adequate size

curing pond to cure the blocks for not less than 21 Days. No other means of curing shall be allowed.

The technical specification of concrete shall confirm to IS 456-2000. The concrete mix is not required to

be designed and only nominal mix as per IS: 456-2000 shall be followed. The proportion of the concrete

mix shall be 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm. nominal size) by

volume. Concrete work shall have fairly exposed concrete surface or as specified in the item. The

designation ordinary M-10, M-15, M-20, M-25 specified as per I.S. corresponds approximately to 1:3:6,

1:2:4, 1:1.5:3 and 1:1:2 nominal mix of ordinary concrete, by volume respectively. The ingredients

required for ordinary concrete containing one bag of cement of 50 Kg. by weight (0.0342 m3.) for

different proportions of mix shall be as per IS 456-2000. The proportion of the aggregate for the kerb

stone shall be modified as per the approval of the engineer-in-charge. The water cement ratios shall not

be more than those specified as per IS. The cement of the mix shall be increased, if the quantity of

water in a mix has to be increased to overcome the difficulties of placement and compaction so that the

water cement ratio specified in the table is not exceeded. The maximum size of coarse aggregate shall

be as large as possible within the limits specified but in no case greater than 1/4th of the minimum

thickness of the member, provided that the concrete can be placed without difficulty so as to surround

all reinforcement thoroughly and to fill the corners of the form. For reinforced concrete work, coarse

aggregates having a nominal size of 20 mm. are generally considered satisfactory. Admixture shall be

used in concrete only with approval of the Engineer-in-charge based upon the evidence that with the

passage of time, neither the compressive strength of concrete is reduced nor are other requisite

qualities of concrete impaired by the use of such admixtures.

Proportioning shall be done by volume, except cement which shall be measured in terms of bags of

kg weight. The volume of one such bag can be taken as 0.0342 m3. Boxes of suitable sizes shall be used

for measuring sand and aggregate. The size of the boxes (internal) shall be 30cm. x 30 cm. and 38 cm.

deep. While measuring the aggregate and sand, the box shall be filled without shaking ramming or

hammering. The proportioning of sand shall be on the basis of its dry volume and in case of damp sand;

allowances for bulk age shall be made.

For all work, concrete shall be mixed in a mechanical mixer which along with other accessories shall be

kept in first class working condition and maintained throughout the construction. Measured quantity of

aggregate, sand, and cement required for each batch shall be poured into the drum of the mechanical

mixer while it is continuously running. After about half a minute of dry-mixing, measured quantity of

water required for each batch of concrete mix shall be added gradually and mixing continued for

another one and a half minute. Mixing shall be continued till materials are uniformly distributed and

uniform colour of the entire mass is obtained and each individual particle of the coarse aggregate shows

complete coating of mortar containing its proportionate amount of cement. In no case shall the mixing

be done for less than 2 minutes after all ingredients have been put into the mixer. Mixers which have

been out of use for more than 30 minutes shall be thoroughly cleaned before putting in a new batch.

Unless otherwise agreed to by the Engineer-in-charge, the first batch of concrete from the mixture shall

contain only 2/3rds of normal quantity of coarse aggregate. Mixing plant shall be thoroughly cleaned

before changing from one type of cement to another.

The degree of consistency which shall depend upon the nature of the work and methods of vibration of

concrete shall be determined by regular slump tests in accordance with IS: 1199-1959. The slump of

mm. to 25 mm. shall be adopted when vibrators are used.

All Moulds shall be cleaned and made free from standing water, dust, snow, or ice immediately before

placing of concrete.

Formwork/Metal Mould for exposed concrete surface (If indicated):

All the moulds shall be checked for exact dimensions of the precast blocks. All the edges of the precast

blocks shall confirm the profile of the final drawing & edges/ curvatures of the moulds shall be checked

accordingly. Moulds shall be regularly checked for correctness of dimensions of Blocks, twists, bends

due to handling, etc. Before starting every days work.

Care shall be taken to set all form work/Mould in perfect line, level (or in required camber or slope as

specified) and plumb. Form work/Mould propping shall be strong, rigid, and sturdy. The form

work/Mould shall be as per pattern & design shown in drawings. Form work/Mould shall be done

accurately and precisely so as to achieve neat, clean and smooth concrete surface, in line, level and

plumb. Clinks, twists, offsets, warps, riveting etc. in plates or forms shall not be allowed. Before placing

concrete, forms shall be thoroughly cleaned off of all rust, dust, and loose materials. Colourless oil or

grease of approved quality shall be applied before placing steel. Also the form work material will be of

wood/plywood/steel or any sort of such material, as approved by the Engineer-in-Charge and/or his

authorized representative; so that all exposed concrete surfaces have uniform colour.

For all kind of exposed concrete work only one brand (to be approved by the Engineer-in charge) of

cement shall be used.

Removal of Moulds:

Specific time shall be identified for removal of moulds, such that the concrete of the precast blocks shall

gain strength to withstand the stresses generated due to self weight and handling to drying yards

without any deformation to shape/ dimensions/ edges.

Sufficient time shall be given to the block after it is removed from the mould so that it can gain strength

and dry in shade to prevent any cracks due to shrinkage. This shall be done in drying yards.

Curing of block shall be done only in curing pond and curing shall be done for minimum 14 days.

Drying period after removing from pond & before delivery to site: Water should be drained of from the

block before it is actually sent to the site. Time should be provided for proper draining of water which

may be present in the block kept for curing in the pond.

Precaution shall be taken while transporting of the blocks to site.

The blocks should be loaded and unloaded with due care so as to avoid generation of stresses leading to

breaking of block. Care should be taken to prevent the block from breaking during transporting.

The pits of the size 150mm in width and required depth shall first be excavated, true to line and level.

The relevant specifications of item A- 1 shall be followed for excavation work. The pits shall be filled

with a layer of 50mm. thick sand bedding. The curbs then shall be placed in position of which 50mm.

shall be below road. Care should be taken to maintain proper line and level. The joints between the

kerbs shall be pointed with C.M. 1:2 and cured for minimum seven days.

Sampling and testing of concrete:

Samples from fresh concrete shall be taken as per IS : 1199-1959 and cubes shall be made, cured and

tested at 7 days or 28 days as per requirements in accordance with IS : 516-1959. A random sampling

procedure shall be adopted to ensure that each concrete batch shall have a reasonable chance of being

tested i.e. the sampling should be spread over the entire period of concreting and cover all mixing units.

At least 1 sample shall be taken from each shift. Ten test specimens shall be made from each sample,

for testing at 7 days, and the remaining 5 at 28 days. The samples of concrete shall be taken on each

day of the concreting as per above frequency. The number of specimens may be suitably increased as

deemed necessary by the Engineer-in-charge when procedure of tests given above reveals a poor

quality of concrete and in other special cases. The average strength of the group of cubes cast for each

day shall not be less than the specified cube strength of 200 Kg/cm2 at 28 days. 20% of the cubes cast

for each day may have value less than the specified strength provided the lowest value is not less than

85% of the specified strength. If the concrete made in accordance with the proportions given for a

particular grade, does not yield the specified strength, such concrete shall be classified as belonging to

the appropriate lower grade. Concrete made in accordance with the proportions given for a particular

grade shall not, however, be placed in a higher grade on the ground that the test strength are higher

than the minimum specified. If rock pockets/honeycombs in the opinion of Engineer-in-charge are of

such an extent or character so as to affect the strength of the structure, materially or to endanger the

life of the steel reinforcement, he may declare the concrete defective and require the removal and

replacement of the portion of the structure affected.

Precast Kerb Stones:

The relevant specifications of concreting as per item above shall be followed except that work shall be

carried out for precast concrete kerb stones as specified in the item. All Precast members shall be cast

at workshop. Sufficient curing shall be done before placement of the same the method of transporting

and placing the precast members shall be as approved by the Engineer-in-charge. Members shall be so

transported that no breakage or undue stresses are induced in them. If required, all members shall have

a key provided on both the faces i.e top and bottom surfaces, of adequate size so as to fill the same

with concrete while laying. The function of this key is to avoid the leakage through the joint between

the precast member and the member on which it is laid.

Mode of Measurements and Payment :

The rate shall include cost of formwork and cost of reinforcement. The volume occupied by

reinforcement shall not be deducted from R.C.C. work.

The rate shall be for a unit of Rmt.

Supplying and fixing of 300 mm-L x 150 mm-B x 380 mm-H Kerb block for Footpath in M-20 grade

using 20 mm nominal size black trap aggregate of Sevaliya/Timba/Ankodiya/Othwad or equivalent

quality for pre-cast blocks, reasonably exposed finish/ formwork , mould with well equipped with

vibratory system for kerb stones of approved design including curing, etc. complete, including the

cost of formwork etc. complete. The rate shall also include necessary cutting of asphalt, fixing the

Kerb stones in line and level on 5 cm thick sand bedding with necessary equipments and materials.

The rate shall also include the flush pointing in CM (1:3) for all joints of the kerbstones. Filling of zari

alone the sides of the kerb stone fixed with Bituminous concrete mixed in proper position as directed

by Engineer in change to form a portable mixture. In any case Gravel or such type of materials shall

not be allowed for production.

Specification as per Item No. 42 only size of kerb as mentioned in Abstract.

Pre cast concrete kerb Providing and fixing M25 Grade of concrete precast exposed / Fair finish /

texture finish kerb stones of approved make as per approved sample of any size and any type. Kerbs

shall be fixed on the foundation prepared as per approved design. The rate shall also include for

erecting and fixing the pieces in position for complete kerb system with chamfered type of kerbs

including necessary accessories of kerb like radius kerb, angles and quadrant kerbs, droplet kerbs etc.

complete as per drawing. Kerb shall be fixed as paper joint without any jointing material. However

cement mortar shall be provided at the backside of kerb stone joint. (Sample must be approved) Cost

of excavation, cutting , base , side filling shall includes as directed engineer - incharge in above item

description as per BOQ (a) 450 mm high median kerb*600*150mm

Specification as per Item No.

Pre cast concrete kerb Providing and fixing M25 Grade of concrete precast exposed / Fair finish /

texture finish kerb stones of approved make as per approved sample of any size and any type. Kerbs

shall be fixed on the foundation prepared as per approved design. The rate shall also include for

erecting and fixing the pieces in position for complete kerb system with chamfered type of kerbs

including necessary accessories of kerb like radius kerbs, angles and quadrant kerbs, droplet kerbs

etc. complete as per drawing. Kerb shall be fixed as paper joint without any jointing material.

However cement mortar shall be provided at the backside of kerb stone joint. (Sample must be

approved) Cost of excavation, cutting , base , side filling shall includes as directed engineer - incharge

in above item description as per BOQ (b) 380 mm high Footpath kerb*600*150mm

Material: (1) Water shall conform to M-1. (2) Cement shall conform to M-3. (3) Sand shall

conform to M-6. (4) Stone aggregate shall conform to M-12 (5) Pre cast kerb shall be of

approved make and as per approved sample.

1.0 Workmanship :

2.1 All Precast exposed/ fare finish/ texture finish kerb stones shall be of approved make.Sufficient

curing shall be done before placement of the same.

2.2 The method of transporting and placing the precast members shall be as approved by theArchitect

and Engineer-in-charge. Members shall be so transported that no breakage orundue stresses are

induced in them.

2.3 The pits of the size 0.15 M in width and 0.23 M. in depth or as per site condition shall first be

excavated, true to line and level. The specifications for excavation shall be followed as per relevant

2.4 The pits shall be filled with a layer of 0.15 M. thick lean concrete M15. The kerbs shall be laid on

existing PCC base in true line and plumb. The specifications for PCC work shall be followed as per

2.5 The rate shall also include for erecting and fixing the pieces in position for complete Kerb systems

with Chamfered type of kerbs including all type of necessary accessories of kerb like Radius Kerbs,

Angles and Quadrant Kerbs, inlet kerbetc complete as per drawing.

The rate shall also include the flush pointing in CM (1:2) for all joints of the kerb stones.

3.0 Mode of Measurement & Payment:

3.1 The rate shall include the cost of material and labour for fixing the kerb system including laying,

jointing and finishing but excluding the cost of excavation, bitumen cutting, base PCC, zari filling with

bitumen material

3.2 The Measurement of the item shall be in Rmt basis.

Providing and fixing pre-cast concrete kerb stone of gray cement based concrete block 30cm

length,30cm height and 15cm thick of M200 grade concret as per approved design and including

excavation for fixing in proper line and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of work is applicable.

Measurements for Payment:

The rate shall be for a unit of one Running meter.

Supplying and fixing for central verge 230 mm L x 235 mm Width x 680 mm H Supplying & Fixing in

M-20 grade using 20 mm nominal size black trap aggregate of Sevaliya/Timba/Ankodiya/Othwad or

equivalent quality for pre-cast blocks,reasonably exposed finish/formwork,mould with well equipped

with vibratory system for kerb stones of approved design including curing,etc.complete,including the

cost of formwork etc.complete.THe rate shall also include necessary cutting of asphalt,fixing the kerb

stones in line and level on 5 cm thick sand bedding with necessary equipments and materials.The rate

shall also include the flush pointing in CM(1:3)for all joints of the kerbstones.Filling of Zari alone the

sides of the kerb stone fixed with bituminous concrete mixed in proper position as directed by

engineer in charge to form a portable mixture.In any case gravel or such type of materials shall not be

allowed for production.

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of work is applicable.

The measurements shall be on Rmt basis.

Providing and Laying of Rubber Moulded Paver Block Grey/Coloured 60 mm thick, M-35 Grade of any

size ; shape (Usually Uni-Paver Blocks) using black trap good quality aggragate of 20 mm nominal size

for footpath, parking areas, service lanes and other areas as mentioned in the drawing / instruction of

Engineer-in-Charge and/or his authorized representative. Cost includes formworks using rubber

mould, Rate providing and laying paver blocks as per required grading and specification. The paver

block shall be mechanically compacted. The work of paving blocks shall be executed in line and level

by skill mason of flooring work only. It should be laid in such a way that the no cutting of the paver

block to be necessary. if cutting of paver block necessary then it should be cut by machine only and

carting. The finished surface of the paver block shall have resonably good, plain finished. Paver blocks

shall be compacted and shall be relaid if necessary. Gravel or such type of materials shall not be

allowed for production. Laying on 50 mm thick sand bedding.

• Laying on 50 mm thick sand bedding.

28.1 Scope of work :

Excavation and compaction up to 300 mm in height for footpath paving in all sorts of soil

murrumincluding sorting outs and stacking of useful materials stuff up to 50mt.

The scope of work includes manufacturing, supplying, and lying of precast paver blocks at various Retail

outlets. The work includes: Verification of the existing site condition and advising our project in charge

to lay suitable base course if required. Contractors are required to satisfy themselves with quality of sub

grade, sub-base course before the paver blocks are laid and suggest strengthening if required.

Clearing the site by removing all obstacles such as stones, debris etc. for laying of paver blocks.

Manufacturing of paver blocks in your plant as per requirements in technical specification enclosed.

Supplying of paver blocks at site, including handling at both ends.

Laying of paver blocks at site as per requirement in technical specification on 50 mm thick sand

bedding, within shortest possible time the site is public place hence care should be taken to ensure that

the routine activities should not be disturbed. The job of laying may required to be carried out during

Testing of paver blocks shall through reputed Govt. /Non Govt. Test house only and submission of test

results as per requirements in Technical Specifications. AMC reserves the right to carryout test at

random. Cost for such tests to be borne by party. The contractor shall guarantee that all material and

components designed, fabricated, supplied, and laid by him shall be free from any type of defect due to

faulty material and/or workmanship/erection for a period of One year from the date of completion of

work. However, the contractor one year's shall render free maintenance.

TECHNICAL SPECIFICATIONS:

28.2 Paver Block Manufacturing Facilities:

The Paver Block shall be made in factory with following minimum facilities:

28.2.1 Concrete Block making Machines:

The machine should be capable of producing high quality Paver Blocks by obtaining high level of

compaction by application of hydraulic compaction and also by high intensity vibration to the

moulds. The machine should have automatic control panel

for uniformity in strength.

28.2.2 Concrete Batching & Mixing Plant: (Not essential)

The concrete Mix Design should be followed for each batch of materials. The concrete ingredient

should be mixed in concrete Batching & Mixing plant with minimum capacity of 30 cum/hour.

The plant should equipped with automatic control panel for maintaining water cement ratio

from batch to batch to obtain concrete of uniform quality and strength. The plant should be

equipped with adequate mechanism for mechanized loading of raw materials into mixer and

conveyor belt for transportation of concrete from mixer to concrete block making machine to

maintain quality of wet cement.

28.2.3 The factory should have well designed curing area to ensure adequate curing of paver blocks.

28.2.4 Laboratory (Desirable but not essential) :

The testing equipment should have required in the Laboratory as per the following:

A Compression testing machine of adequate capacity.

Other tools and equipment for testing raw materials and paver blocks.

Systematic record of test results of various paver blocks manufactured in the factory.

Concrete Mix Design for various grade of concrete used for making of paver blocks.

28.3 Specifications For Coloured Paver Blocks:

Coloured concrete paver blocks shall be manufactured as per attached specifications using or

equivalent approved colour Pigment of “BAYER” Make “BAYFERROX IRONOXIDE PIGMENTS”

with minimum colour pigment of 3% by weight of cement. The colour shade shall be “RED” as

selected by AMC before commencement of the work. White cement shall be used for colored

pavers to obtain the desired colour shade. The job also includes providing 50 mm thick sand

bedding to match the shade of the paver block.

The colour of the paver block shall be guaranteed against fading of colour for period of

months from the date of laying of the same at site.

All other technical specifications & Procedure for testing, laying & sampling of coloured pavers

will be as per attachment.

28.4 Pavers Block Characteristics:

The concrete pavers should have perpendicularities after release from the mould and the same

should be retained until the laying. The surface should be reasonably smooth and of anti skid

and anti glare type. The paver should have uniform chamfers to facilitate easy drainage surface

run off. The pavers should have uniform interlocking space of 2mm to 3mm to ensure

compacted sand filling after vibration on the paver Surface. The concrete mix design should be

followed for each batch of materials separately and automatic batching plant is to be used to

achieve uniformity in strength and quality. The pavers shall be manufactured in single layer

only. Skilled labour should be employed for laying blocks to ensure line and level of laying,

desired shape of the surface and adequate compaction of the sand in the joints. The pavers shall

be of cement gray colour without any pigment & for coloured pavers refer “specifications for

coloured pave`” The pavers are to be skirted all round with kerbing using solid concrete blocks of

size 150mm X 250mm X 380mm. The kerbing should be embedded for 100mm depth. The

concrete used for kerbing shall be cured properly for 7 days minimum.

28.5 Paver Block Dimensions:

Thickness 60 mm

Shape Unipaver, I shape or directed by Addl.C.E.

Chamfer 4mm to 6mm along top edges

Colour Natural cement grey colour without use of any

For coloured pavers refer “specifications for coloured

Dimensional (+/-) 2mm for length & width,

Tolerance (+/-) 3mm for Height (Thickness)

28.6 Testing of Paver Blocks :

* TEST Average Values Frequency

1. Compressive Min. 35 N/Sq mm for 250 Smt / 1 Test

Strength 60mm thick

Minimum 4.5 N/Sq

2. Flexural Strength

3. Abrasion Resistance Maximum

4. Water Absorption Maximum 5.80%

* Sampling and testing procedure as per enclosed specifications

28.7 Sampling and Testing Procedure for Paver Blocks

INTERNAL – Average of minimum 3 samples per 5000 Blocks.

28.7.1 Sampling for Testing

Sampling of Paver blocks.

Method of sampling :

Before laying paver blocks, each designated section comprising not more than 50000 blocks,

shall be divided into ten approximately equal groups. Three blocks shall be drawn from each

Marking and identification :

All samples shall be clearly marked at the time of sampling in such a way that the designated

section of part thereof, and the consignment represented by the sample, are clearly defined.

The sample shall be dispatched to the approved test laboratory taking precaution to avoid

damage to the paving in transit. Protect the paving from damage and contamination until they

have been tested. The testing shall be carried as soon as possible, after the sample has been

taken. As soon as practicable after sampling. The samples shall be stored in water at 20 degree C

 5 degree C for 24 hours prior to testing.

The item is to be executed as per instructions and to the entire satisfaction of Engineer-in-

Charge and/or his authorized representative using Rubber mould and Table vibrator for Kerb

instead of mechanical press system.

Extra rate for excavation of asphalt payment of any thickness including demolishing the asphalt

carpet, metal, soling etc. complete with stacking the materials as directed. The road surface of

asphalt shall carefully be opened to full width as directed by the Engineer-in-Charge and/or his

authorized representative.

Excavation area shall be properly identified and marked in rectangular shape. The road crust

shall be opened up to entire depth i.e. including soling. All the materials shall be separately

deposited in such a way and in places as may be determined by the Engineer-in-Charge and/or

his authorized representative. In case rubble not being so deposited or being mixed up with the

excavated materials will not be allowed for refilling. The cost of materials shall be charged from

the contractor. The decision of the C.E. shall be final and binding to the contract

For detailed specification for Laying of Paver Block on sand bedding, refer R & B Department

booklet for General Technical Specification for building works.

The rate shall be for a unit of SMT

Providing and laying of interlocking grey paver blocks of high density 80mm thick made from M-40

grade concrete using 6 mm to 20 mm machine crushed well graded stone aggregate, sand of

approved quality, OPC 53 grade cement with contractor's own concrete mix design as approved by

AMC, for parking, road. Cost Includes formwork, using rubber/FRP mould, laying paver block as per

required grading and specification laid paver block shall be mechanically compacted. The work of the

paving blocks shall be executed in line and level by skilled mason of flooring work only. It should be

laid in such a way that the no cutting of the paver block to be necessary. Cutting of paver block by

machine cut only and carting to be done. The Finished surface of the Paver Block shall have

reasonably good plain finish. Paver blocks shall be compacted and shall be re-laid if necessary. Gravel

or such type of materials shall not be allowed for production. Laying on 5 Cms thick sand

bedding.(AMC approved Rate )

For relevant Specification of Item as per item description & instruction of Engineer-in-Charge and/or his

authorized representative.

The mode of payment for this item shall be on RMT. Basis.

Providing and laying shot blasted Non - interlocking, Paver blocks of specified thickness, size, grade of

concrete and colour machine made and blasting by automatic shot blasting machine and high density

of as per approved sample of approved make for footpath, parking areas, service lanes,cross over and

other areas as mentioned in the drawing. Including providing and laying 50 mm thick averave bedding

layer of coarse sand below paver block as per required grading and specification. Laid paver block

shall be mechanically compacted. The work of the paving blocks shall be executed in line and level by

skilled mason of flooring work only. Small size of paver block with same specification shall be used at

residue or at end. It should be laid in such a way that the no cutting of the paver block to be

necessary. If cutting of paver block shall be required , than cut by machine only and laying to be done

by skilled flooring mason. The finished surface of the paver block shall have coarse sand Texture

Finish. Pave blocks shall be compacted and shall be re-laid if necessary. Actual laid area shall be

measured and paid without any wastage. (A) 60 mm thick M-35 grade Grey Paver block of size

Specification as per Item No.

Providing and laying shot blasted Non - interlocking, Paver blocks of specified thickness, size, grade of

concrete and colour machine made and blasting by automatic shot blasting machine and high density

of as per approved sample of approved make for footpath, parking areas, service lanes,cross over and

other areas as mentioned in the drawing. Including providing and laying 50 mm thick averave bedding

layer of coarse sand below paver block as per required grading and specification. Laid paver block

shall be mechanically compacted. The work of the paving blocks shall be executed in line and level by

skilled mason of flooring work only. Small size of paver block with same specification shall be used at

residue or at end. It should be laid in such a way that the no cutting of the paver block to be

necessary. If cutting of paver block shall be required , than cut by machine only and laying to be done

by skilled flooring mason. The finished surface of the paver block shall have coarse sand Texture

Finish. Pave blocks shall be compacted and shall be re-laid if necessary. Actual laid area shall be

measured and paid without any wastage. (A) 80 mm thick M-35 grade Grey Paver block of size

1.0 The scope of work: It includes supplying and laying of Precast shot blasted by automatic shot

blasting machine in factory (not on site) paver blocks at footpath, parking area, service lane and other

The work includes:

1.1 Paver block should be laid over prepared sub grade.

1.2 Clearing the site by removing all obstacles such as stones, debris etc. for laying of paver blocks.

1.3 Manufacturing of paver blocks by one of the approved suppliers as per requirements intechnical

specification enclosed.

1.4 Supplying of paver blocks at site, including handling at both ends. The type of paver block may be

interlocking or non-interlocking.

1.5 Providing and laying average 50 mm coarse sand bedding for laying blocks.

1.6 Laying of paver blocks at site as per requirement in technical specification, within shortest possible

1.7 Testing of paver blocks through reputed Govt. /Non Govt. Test house and submission of test results

as per requirements in Technical Specifications. Client reserves the right to carryout test at random.

Cost for such tests to be borne by contractor.

1.8 The contractor shall guarantee that all material and components designed, fabricated, supplied and

laid by him shall be free from any type of defect due to faulty material and/or workmanship/erection

for a period of five year from the date of completion of work at individual sites. However, the

contractor for five years shall render free maintenance.

2.0 Technical Specifications:

2.1 Paver Block Manufacturing Facilities:

The Paver Block shall be made in factory with following minimum facilities:

Concrete Block making Machines:

The machine should be capable of producing high quality Paver Blocks by obtaining high level of

compaction by application of hydraulic compaction and also by high intensity vibration to the moulds.

The machine should have automatic control panel for uniformity in strength.

Concrete Batching & Mixing Plant: (Not essential) The concrete Mix Design should be followed for each

batch of materials. The concrete ingredient should be mixed in concrete Batching & Mixing plant with

minimum capacity of 30 cum/hour. The plant should be equipped with automatic control panel for

maintaining water cement ratio from batch to batch to obtain concrete of uniform quality and strength.

The plant should be equipped with adequate mechanism for mechanized loading of raw materials into

mixer and conveyor belt for transportation of concrete from mixer to concrete block making machine

to maintain quality of wet cement.

The factory should have well designed curing area to ensure adequate curing of paver blocks. Steam

curing facility of the paver blocks is preferable.

Laboratory (Desirable but not essential) :

The factory should have the following:

Compression testing machine of adequate capacity.

Other tools and equipment for testing raw materials and paver blocks.

(1) Systematic record of test results of various paver blocks manufactured in the factory.

(2) Concrete Mix Design for various grade of concrete used for making of paver blocks.

2.2 Specifications for Coloured Paver Blocks:

Colour concrete paver blocks shall be manufactured as per attached specifications using approved

colour Pigment of iron oxide of approved brand like Bayer, Tata etc. with minimum colour pigment of

3% by weight of cement. The colour shade shall be as selected by Architect before commencement of

the work. The job also includes providing 50 mm thick sand bedding to match the shade of the paver

The colour of the paver block shall be guaranteed against fading of colour for period of 12 months from

the date of laying of the same at site.

All other technical specifications & Procedure for testing, laying & sampling of Color pavers will be as

per attachment.

2.3 Paver Block Characteristics:

The concrete pavers should have perpendicularities after release from the mould and the same should

be retained until the laying.

The surface should be reasonably smooth and of anti skid and anti glare type. The paver should have

uniform chamfers to facilitate easy drainage surface run off.

The pavers should have uniform interlocking space of 2mm to 3mm to ensure compacted sand filling

after vibration on the paver Surface.

The concrete mix design should be followed for each batch of materials separately and automatic

batching plant is to be used to achieve uniformity in strength and quality.

The pavers shall be manufactured in Double layer only.

Skilled labour should be employed for laying blocks to ensure line and level of laying, desired shape of

the surface and adequate compaction of the sand in the joints.

2.4 Paver Block Dimensions:

Layers Double layered, top layer minimum 8 to 10 mm

Shape Irregular (Uniform Shape with no Hollow Or Cracks) / as per drawing

Chamfer 4mm to 6mm along top edges

Colour Natural cement grey Colour without use of any pigment.

For Colour pavers refer “specifications for Colour pavers”

Dimensional (+/-) 2mm for length & width,

Tolerance (+/-) 3mm for Height (Thickness)

2.5 Testing of Paver Blocks:

* Sampling and testing procedure as per enclosed specifications

3.0 Sampling & Testing Procedures for Paver Blocks:

3.1 Sample Size:

INTERNAL – Average of minimum 3 samples per 10000 Blocks for compressive strength and water

EXTERNAL – Minimum 2 Blocks per 10000 blocks for abrasion and flexure.

3.2 Sampling For Testing: Sampling for testing of paver blocks shall be done in accordance with

Compressive Strength: Testing for compressive strength shall be undertaken in accordance with

Appendix-B. The average compressive strength of the blocks tested shall be 30/40 N/Sq.mm as per

Abrasion Resistance: Testing for abrasion shall be in accordance with IS 1237 (Specifications for Cement

Concrete Floor Tiles).

Flexural Strength: Testing for flexural shall be in accordance with IS 1237 (Specifications for Cement

Concrete Floor Tiles).

Water Absorption: Testing for water absorption shall be in accordance with IS 2185:1979: Part I

(Specifications for Concrete Masonry Units).

Method of sampling: Before laying paver blocks, each designated section comprising not more than

10000 blocks, shall be divided into five approximately equal groups. One block shall be drawn from each

group i.e. 3 for internal testing and 2 for external testing.

Marking and identification: All samples shall be clearly marked at the time of sampling in such a way

that the designated sections of part thereof, and the consignment represented by the sample, are

clearly defined.The sample shall be dispatched to the approved test laboratory taking precaution to

avoid damage to the paving in transit. Protect the paving from damage and contamination until they

have been tested. The testing shall be carried as soon as possible, after the sample has been taken. As

soon as practicable after sampling. The samples shall be stored in water at 20 degree oC for 24 hours

prior to testing.

SR.NO. * TEST SPECIFICATION Average Values

(Average of Minimum Five Samples/Site)

1. Compressive Strength Min. 30 N/Sq.mm for 60mm thick and Min. 40 N/Sq.mm

2. Flexural Strength Minimum 3.80 N/Sq.mm and 4.5 N/ Sq. mm for 60 and

mm thick paver block respectively.

3. Abrasion Resistance Maximum

4. Water Absorption Maximum 5.80%

5. Minimum Cement Content 380 Kg/Cum for M 30 concrete and 430 Kg/Cum for M 40 concrete

3.0 Sampling & Testing Procedures for Paver Blocks:

3.1 Sample Size:

INTERNAL – Average of minimum 3 samples per 10000 Blocks for compressive strength and water

EXTERNAL – Minimum 2 Blocks per 10000 blocks for abrasion and flexure.

3.2 Sampling For Testing: Sampling for testing of paver blocks shall be done in accordance with

Compressive Strength: Testing for compressive strength shall be undertaken in accordance with

Appendix-B. The average compressive strength of the blocks tested shall be 30/40 N/Sq.mm as per

Abrasion Resistance: Testing for abrasion shall be in accordance with IS 1237 (Specifications for Cement

Concrete Floor Tiles).

Flexural Strength: Testing for flexural shall be in accordance with IS 1237 (Specifications for Cement

Concrete Floor Tiles).

Water Absorption: Testing for water absorption shall be in accordance with IS 2185:1979: Part I

(Specifications for Concrete Masonry Units).

Method of sampling: Before laying paver blocks, each designated section comprising not more than

10000 blocks, shall be divided into five approximately equal groups. One block shall be drawn from each

group i.e. 3 for internal testing and 2 for external testing.

Marking and identification: All samples shall be clearly marked at the time of sampling in such a way

that the designated sections of part thereof, and the consignment represented by the sample, are

clearly defined.

The sample shall be dispatched to the approved test laboratory taking precaution to avoid damage to

the paving in transit. Protect the paving from damage and contamination until they have been tested.

The testing shall be carried as soon as possible, after the sample has been taken. As soon as practicable

after sampling. The samples shall be stored in water at 20 degree C 5 degree C for 24 hours prior to

Test For Compressive Strength:

Testing Machine: The testing machine shall be of suitable capacity for the test and capable of applying

the load of the rate specified. It shall comply, as regards repeatability and accuracy, with the

requirements of clause 2.1 of BS: 1881-Part

Procedure: The sample specimen shall be tested in a wet condition after being stored for at least

hours in water maintained at a temperature of 20 oC + or – 5 oC. Before thespecimens are submerged in

water, the necessary area shall be determined.

The plates for testing machines shall be wiped clean and any loose grit or other material removed from

the contact faces of the specimen. Plywood, nominally 4 mm thick shall be used as packing between the

upper and lower faces of the specimen and the machine plates and these boards shall be larger than

the specimen by the margin of at least 5 mm

at all points. Fresh Packing shall be used for every specimen tested.

The specimen shall be placed in the machine with the wearing surface in the horizontal plane and in

such a way that the axes of the specimen are aligned with those of the machine plates.

The load shall be applied without shock and increased continuously at the rate of approximately 15 N/

Sq.mm per minute until no greater load can be sustained. The maximum load applied to the specimen

shall be recorded.

Calculation of corrected strength for individual Blocks: The compressive strength of each block

specimen shall be calculated by dividing the maximum load by full cross section area of the block and

multiplying with an appropriate factor of:-

a) For 100 mm thick blocks –

b) For 80 mm thick blocks –

c) For 60 mm thick blocks –

Compressive Strength Calculation: The average corrected compressive strength for the designed block

section shall be calculated.

4.0 Method of laying:

Blocks shall be placed on the sand bedding etc. which were well rammed so as to act as firm bed. Blocks

shall be laid in such manner that no gap shall be left in between. Blocks so laid shall be compacted by

means of mechanical compactor or equivalent compacting method so as to obtain required finished

surface. All the joints shall be matched and if any manufacturing defect is detected the lot shall be

replaced and relaying shall be done with out any extra cost up to satisfaction of Engineer in charge.

50 to 80mm thick coarse sand shall be laid as cushioning layer for arranging the paver blocks. Joints of

the paver blocks shall be filled with the sand.

The paver blocks shall be laid properly on the prepared sub-base as per manufacturer's specification

and as per Architect and Engineer-in-charge's instruction.

Paver block shall be laid by the approved agency only. If manufacturer of the paver block providing the

laying services, then it shall be laid through the supplying agency only. The labourers for paver block

fixing shall be skilled flooring mason only. Only cutting tool shall be used for cutting the paver block. Full

depth cutting toll shall be used for proper finished surface after cutting. Manual cutting or breaking of

the paver block is not permitted.

After laying of the paver block fine sand shall be spread over it and paver block shall be compacted with

mechanical compactor. Any settlement or undulation in the laid area shall be repaired immediately.

5.0 Mode of Measurement and payment:

Measurement shall be done as per actual area laid without considering any wastage.

The Measurement of the item shall be in Sqmt basis.

Labour work of fixing kurb any design of central verge, (both side) footpath kurb, items includes

necessary excavation, asphalt cutting of any thickness, erecting in line and position and pointing with

cement mortar (1:3), watering, etc complete, filling with zari along the side of the kurb, the kurb

stone fix prepared with bitumnious top surface, as directed by engineer in charge.

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of laying of paver blockis applicable.

The measurements shall be on RMT basis.

Paver Block Providing and laying, Dished Channel specified thickness, size, grade of concrete and

colour machine made and blasting by automatic shot blasting machine and high density of as per

approved sample of approved make for suite drain besides paking area and other areas as mentioned

in the drawing. Including providing and laying 50 mm thick average bedding layer of coarse sand

below dished channel as per required grading and specification. Laid dished channel shall be

mechanically compacted. The work of the dished channel shall be executed in line and level by skilled

mason. Small size of dished channel with same specification shall be used at residue or at end. If

cutting of dished channel shall be required , than cut by machine only and laying to be done by skilled

flooring mason. Actual laid area shall be measured and paid without any wastage. (A) 600 mm X

mm X 100 mm thick M-25 grade Grey dished curved channel

As per item decription or as decided by engineer in charge.

The Measurement of the item shall be in rmt.

Supply and installation of concrete bollard of size 300mm diameter x 900mm height, constructed

using M-30 concrete and 4nos 8mm dia MS Fe500 reinforcement through the section as directed by

EIC including supply of all material, labour and equipment upto any lead and lift

For relevant Specification of Item as per item description & instruction of Engineer-in-Charge, M.O.R.T

& H. latest Specifiaction& IS CODE and/or his authorized representative. refer R & B Department

booklet for General Technical Specification for building works.

The mode of payment for this item shall be on No. Basis.

Construction of RCC nosing in central verge using M-200 grade cement concrete. The item includes

cost of centering & shuttering, reinforcement, both side cement plaster in C:M 1:3 mortar & curing

etc. complete. Half round portion of the nosing shall be made by using mild steel.

Work shall be carried out as per item description including cost of all labour and materials etc. complete

as directed. General standard practice of work is applicable.

As per Item and instructed by engineer incharge

The rate shall be for a unit of Nos

Providing, supplying and fixing precast C.C. blocks (M-20) edge kerb having size of 75 x 300 x 300 mm

depth and as per design conveying it to the site, jointing into C:M 1:3 and racking out the joints incl.

necessary excavation of asphalt, soil etc..completed.

The specifiction of following materials shall be conforming with specification mentioned for relavent

material / items in General technical specification for building work of R&B Department of Gujarat.

Water shall conform to M-1Cement to M-2

Sand to M-5Grit to M-7.

Graded stone aggregate 20 mm. nominal size to M-10

Contractor shall have to manufacture the blocks as per the dimensions given in the drawing. Specific

machineries shall be used to manufacture the precast blocks. These machineries should be

compatible to produce blocks of required strength and dimensions. The machine shall contain

hydraulic Press or advanced equipment to generate required compaction & Grade and finish.

Moulds/ Steel Plates/ Dies of the machine shall be dimensionally checked & to be got approved

before commencing the production. Contractor shall prepare proper Drying Yard for keeping the

blocks before curing. The drying yard shall be levelled and covered so that no shrinkage cracks are

formed. Contractor shall prepare adequate size curing pond to cure the blocks for not less than

Days. No other means of curing shall be allowed. The technical specification of concrete shall confirm

2000. The concrete mix is not required to be designed and only nominal mix as per IS: 456-2000 shall

be followed. The proportion of the concrete mix shall be 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded

stone aggregate 20 mm. nominal size) by volume. Concrete work shall have fairly exposed concrete

surface or as specified in the item. The designation ordinary M-10, M-15, M-20, M-25 specified as per

I.S. corresponds approximately to 1:3:6, 1:2:4, 1:1.5:3 and 1:1:2 nominal mix of ordinary concrete, by

volume respectively. The ingredients required for ordinary concrete containing one bag of cement of

50 Kg. by weight (0.0342 m3.) for different proportions of mix shall be as per IS 456-2000. The

proportion of the aggregate for the kerb stone shall be modified as per the approval of the engineer-

in-charge. The water cement ratios shall not be more than those specified as per IS. The cement of

the mix shall be increased, if the quantity of water in a mix has to be increased to overcome the

difficulties of placement and compaction so that the water cement ratio specified in the table is not

exceeded. The maximum size of coarse aggregate shall be as large as possible within the limits

specified but in no case greater than 1/4th of the minimum thickness of the member, provided that

the concrete can be placed without difficulty so as to surround all reinforcement thoroughly and to

fill the corners of the form. For reinforced concrete work, coarse aggregates having a nominal size of

20 mm. are generally considered satisfactory. Admixture shall be used in concrete only with approval

of the Engineer-in-charge based upon the evidence that with the passage of time, neither the

compressive strength of concrete is reduced nor are other requisite qualities of concrete impaired by

the use of such admixtures.

Proportioning shall be done by volume, except cement which shall be measured in terms of bags of

50 kg weight. The volume of one such bag can be taken as 0.0342 m3. Boxes of suitable sizes shall be

used for measuring sand and aggregate. The size of the boxes (internal) shall be 30cm. x 30 cm. and

38 cm. deep. While measuring the aggregate and sand, the box shall be filled without shaking

ramming or hammering. The proportioning of sand shall be on the basis of its dry volume and in case

of damp sand; allowances for bulk age shall be made.

For all work, concrete shall be mixed in a mechanical mixer which along with other accessories shall

be kept in first class working condition and maintained throughout the construction. Measured

quantity of aggregate, sand, and cement required for each batch shall be poured into the drum of the

mechanical mixer while it is continuously running. After about half a minute of dry- mixing, measured

quantity of water required for each batch of concrete mix shall be added gradually and mixing

continued for another one and a half minute. Mixing shall be continued till materials are uniformly

distributed and uniform colour of the entire mass is obtained and each individual particle of the

coarse aggregate shows complete coating of mortar containing its proportionate amount of cement.

In no case shall the mixing be done for less than 2 minutes after all ingredients have been put into the

mixer. Mixers which have been out of use for more than 30 minutes shall be thoroughly cleaned

before putting in a new batch. Unless otherwise agreed to by the Engineer-in-charge, the first batch

of concrete from the mixture shall contain only 2/3rds of normal quantity of coarse aggregate. Mixing

plant shall be thoroughly cleaned before changing from one type of cement to another.

The degree of consistency which shall depend upon the nature of the work and methods of vibration

of concrete shall be determined by regular slump tests in accordance with IS: 1199-1959. The slump

of 10 mm. to 25 mm. shall be adopted when vibrators are used.

All Moulds shall be cleaned and made free from standing water, dust, snow, or ice immediately

before placing of concrete. Formwork/Metal Mould for exposed concrete surface (If indicated):

All the moulds shall be checked for exact dimensions of the precast blocks. All the edges of the

precast blocks shall confirm the

profile of the final drawing & edges/ curvatures of the moulds shall be checked accordingly. Moulds

shall be regularly checked for correctness of dimensions of Blocks, twists, bends due to handling, etc.

Before starting every days work.

Care shall be taken to set all form work/Mould in perfect line, level (or in required camber or slope as

specified) and plumb. Form work/Mould propping shall be strong, rigid, and sturdy. The form

work/Mould shall be as per pattern & design shown in drawings. Form work/Mould shall be done

accurately and precisely so as to achieve neat, clean and smooth concrete surface, in line, level and

plumb. Clinks, twists, offsets, warps, riveting etc. in plates or forms shall not be allowed. Before

placing concrete, forms shall be thoroughly cleaned off of all rust, dust, and loose materials.

Colourless oil or grease of approved quality shall be applied before placing steel. Also the form

work material will be of wood/plywood/steel or any sort of such material, as

approved by the Engineer-in-Charge and/or his authorized representative; so that all exposed

concrete surfaces have uniform colour.

For all kind of exposed concrete work only one brand (to be approved by the Engineer-in charge) of

cement shall be used.

Removal of Moulds:

Specific time shall be identified for removal of moulds, such that the concrete of the precast blocks

shall gain strength to withstand the stresses generated due to self weight and handling to drying

yards without any deformation to shape/ dimensions/ edges.

Sufficient time shall be given to the block after it is removed from the mould so that it can gain

strength and dry in shade to prevent any cracks due to shrinkage. This shall be done in drying yards.

Curing of block shall be done only in curing pond and curing shall be done for minimum 14 days.

Drying period after removing from pond & before delivery to site: Water should be drained of from

the block before it is actually sent to the site. Time should be provided for proper draining of water

which may be present in the block kept for curing in the pond.

Precaution shall be taken while transporting of the blocks to site.

The blocks should be loaded and unloaded with due care so as to avoid generation of stresses

leading to breaking of block. Care should be taken to prevent the block from breaking during

The pits of the size 150mm in width and required depth shall first be excavated, true to line and level.

The relevant specifications of item A- 1 shall be followed for excavation work. The pits shall be filled

with a layer of 50mm. thick sand bedding. The curbs then shall be placed in position of which 50mm.

shall be below road. Care should be taken to maintain proper line and level. The joints between the

kerbs shall be pointed with C.M. 1:2 and cured for minimum seven days.

Sampling and testing of concrete:

Samples from fresh concrete shall be taken as per IS : 1199-1959 and cubes shall be made, cured and

tested at 7 days or 28 days as per requirements in accordance with IS : 516-1959. A random sampling

procedure shall be adopted to ensure that each concrete batch shall have a reasonable chance of

being tested i.e. the sampling should be spread over the entire period of concreting and cover all

At least 1 sample shall be taken from each shift. Ten test specimens shall be made from each sample,

5 for testing at 7 days, and the remaining 5 at 28 days. The samples of concrete shall be taken on

each day of the concreting as per above frequency. The number of specimens may be suitably

increased as deemed necessary by the Engineer-in-charge when procedure of tests given above

reveals a poor quality of concrete and in other special cases. The average strength of the group of

cubes cast for each day shall not be less than the specified cube strength of 200 Kg/cm2 at 28 days.

20% of the cubes cast for each day may have value less than the specified strength provided the

lowest value is not less than 85% of the specified strength. If the concrete made in accordance with

the proportions given for a particular grade, does not yield the specified strength, such concrete shall

be classified as belonging to the appropriate lower grade. Concrete made in accordance with the

proportions given for a particular grade shall not, however, be placed in a higher grade on the ground

that the test strength are higher than the minimum specified. If rock pockets/honeycombs in the

opinion of Engineer-in-charge are of such an extent or character so as to affect the strength of the

structure, materially or to endanger the life of the steel reinforcement, he may declare the concrete

defective and require the removal and replacement of the portion of the structure affected.

Precast Kerb Stones:

The relevant specifications of concreting as per item above shall be followed except that work shall

be carried out for precast concrete kerb stones as specified in the item. All Precast members shall be

cast at workshop. Sufficient curing shall be done before placement of the same the method of

transporting and placing the precast members shall be as approved by the Engineer-in-charge.

Members shall be so transported that no breakage or undue stresses are induced in them. If

required, all members shall have a key provided on both the faces i.e top and bottom surfaces, of

adequate size so as to fill the same with concrete while laying. The function of this key is to avoid the

leakage through the joint between the precast member and the member on which it is laid.

Mode of Measurements and Payment :

The rate shall include cost of formwork and cost of reinforcement. The volume occupied by

reinforcement shall not be deducted from R.C.C. work.

The rate shall be for a unit of Rmt.

Supplying & Fixing Nimbhada ladi 37 to 50 mm thick for walk way covering the activity of

excavation,ramming,laying on sand bedding as per requirement to fix the Nibhada stone in Line &

Level with cement pointing in cement mortar 1:2 etc complete as directed.

The mode of measurnment shall be on Smt basis.

Labour work for fixing interlocking blocks / any kind of pavement on up to 50 mm th sand bedding,

levelling, watering and fixing in line & level as well cleaning the site etc.comp. as directed.

Work shall be carried out as per item description including cost of all labour and materials etc.

complete as directed. General standard practice of laying of paver block is applicable.

The measurements shall be on SMT basis.

Bitumen Cutting Labour Charges Of Cutting in bituminous pavement.Cutting to be done with heavy

duty tandom cutting machine consist of dianond level.Minimum Cutting Depth Shall be 75 mm From

the finished Level.Cutting Shall be perfectly in line.the width and depth of the removal of asphalt

towards kerb stone shall be as per the drawing.bitumin Shall be Carefully Removed so that the

cutting edge towards the road should not be disturbed.The work of Removal of asphalt will be

considered in this item as running meter of the cutting done by machine.one cutting line will be

considered per length of the kerb stone.Bitumen and Other Debrise shall be disposed within

km.as per the instruction of the engineer in charge.Surroundings Shall be cleaned to the satisfaction

of engineer in Charge.

The measurements shall be on RMT basis.

Supplying, fabricating and placing in position reinforcement TMT bars Fe- 500, yield stress not less

than 500 N/mm2 bars confirming to IS- 1786 reinforcement for RCC structure / items as per

design including transporting steel to the work site, handling wastage, decoiling, cutting, bending,

cranking, fabricating to required shape, placing in position, binding with 18 guage (1.22 mm) GI

wires, welding if necessary by using approved welding rods etc. for all levels, all place, all height

as per drawing etc. complete as directed by the engineer-in-charge. The quoted rate should

be inclusive the cost of binding wire, chairs, pins, brackets and the same will not be measured

and paid separately. (Rolling margin's and wastage shall not be paid.) Measurement shall be made on

the length basis and convert into weight by using standard co- efficient.

SOR 23-24 IT CD NO :05014C

For relevant Specification of Item as per item description & instruction of Engineer-in-Charge and/or his

authorized representative.

Mode of measurements shall be on Kg basis.

Providing Formwork of ordinary timber planking so as to give a rough finish including centering

shuttering strutting and propping etc. Height of propping and centering below supporting floor to

ceiling not exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete

work in. (A)Foundations Footings Bases of Columns etc. and Mass concrete. (Item Code : 09001AA,

SOR 2021-22, R & B Ahmedabad City

Providing Formwork of ordinary timber planking so as to give a roughfinish including centering shuttering

strutting and propping etc. Height of propping and centering below supporting floor to ceiling not

exceeding 4 M. and removal of the same for in situ reinforced concrete and plain concrete work in.

(A)Foundations Footings Bases of Columns etc. and Mass concrete.

Mode of measurements shall be on SMT basis

P/A Tremix with dewartering machine and floater machine on constructed CC work for finishing the

surface as per requirement. The rate including all machinaries, labor, loading, unloading,

transportaion etc complete as per direction given by engineer in charge.

Providing & Applying Trimix with dewatering machine and floater machine on constructed RCC work

incl.cost of machine and labour etc comp as directed. As directed by engineer in charge

Making 15 mm. Groove in RCC work on road & filling it with polysulfied selant & finished ot good

incl. all labour charges etc. comp.as directed.

Making 15 mm groove in RCC work on road and filling it with polysulfied selant and finished it good

incl.all labour charges etc comp as directed. As directed by engineer in charge.

The mode of measurement shall be on Rmt of basis.

Providing & Supplying JCB Machine on rental basis in case of emergency situation and break down

type work & also during unavoidable condition as per instruction of engg.incharge , rate includes all

nece. shifting, fuel and operating charges and stacking of useful & non-useful materials separately up

to store. (No payment should be allowed for non working condition of machinery and for pipe line

excavation and laying work)

Item includes Providing & Supplying JCB machine for RCC/ Asphalt cutting and heavy excavation

in Case of heavy traffic Main road, rate includes all necessary shifting, fuel and operating charges and

stacking of usefull & unusefull materials separatly up to store Measurement shall be paid by Hr. basis.

Hiring of Tractor with trolley considering 8 Hrs. As working Day hours inclu. Driver (GWSSB SOR 2021-

The M/s shall be on Day basis.

Supplying, labour for excavation of all types of soil at any depth including excavation of asphalt

pavement of any thickness,demolit ion of brick work in CM of any proportion including stacking of

serviceable materials and disposal of unserviceable material etc. comp. as directed.

The M/s shall be on No basis.

Providing and suppplying Roller for compacting the road bhuva with available building waste and

Road waste material as and where directed by engineer in charge.

The measurement shall be in Shift.

Rent for Providing Chota Hathi (Light weight vehicle) with Driver at shown site incl. necessary

oil/diesel/petrol for vehical and all other charges.Work Done as per Instruction of incharge etc.

Complete as Directed.

The measurement shall be in Shift.

Contractor’s Signature Add.City Engineer

13. કો ાકટર ારા ESIC અને EPFO ર શન ગેના અ. .ુ કોપ . નાણાં ખાતા સર લ

ુ ર નં- ૨૭, તા ૦૭/૦૧/૨૦૨૬ ુ બ ESIC અને EPFO

ftuLx[tfxhle mne - rm¬tu yuze.mexe yuLSlegh

btuctEj lkch mt&u (œrûtK Ítul)

FOR BANK GUARANTEE

Seal and Signature of the Bidder Add. City Engineer (South Zone)

AHMEDABAD MUNICIPAL CORPORATION

ENGINEERING DEPARTMENT

General terms & conditions

1. A booklet of FORM B-1 of Gujarat State Roads & Building Department / Water Resources

Department with the latest correction slips may be referred for quality of construction &

standard of Procedure (SOP). (only English version)

2. In the specification “as directed" / "approved" shall be taken to mean "as directed /

"approved" by the Engineering in charge.

3. Wherever a reference to any Indian standard appears in the specifications, it shall be taken

to mean as reference to the latest edition of the same of force on the date of agreement.

4. In "Mode of measurement" in the specifications wherever a dispute arises in the absence of

specific mention for a particulars point / aspect, the same in the relevant Indian Standards

shall be referred to.

5. All measurement and computations, unless otherwise specified shall be carried out nearest

to the following limits :-

i) Length, width and depth, Height 0.01 Meter

ii) Areas 0.01 Sq.mts.

iii) Cubic contents 0.01 Cu. mts.

In recording dimensions of work, the sequence of length, width and height (Depth) or

thickness shall be followed.

6. Definite particulars covered in the items of work, though not mentioned or elucidate in its

specifications shall be deemed to be included therein.

7. Approval of the samples of various materials given by the Engineer in charge or AMC's

Consultant shall not absolve the contractor from the responsibility of replacing defective

materials brought on site or materials used in the work found defective at a later date. The

contractor shall have no claim to any payment or compensation whatsoever on account of

any such materials being rejected by the Engineer in charge.

8. The contractor’s rate for the item of work shall be for the work completed in all respect.

9. All materials including those of electrical shall be got approved by the Engineer in charge/

Architect before using them in the work.

10. Materials as and when rejected by the Engineer in charge or AMC's Consultant shall be

removed from the site of work within 24 hours.

11. All work shall be carried out in a manner applying the best technique.

12. All tools, templates, machinery and equipment for correct execution of the work as well as

for checking lines, levels, alignment of the works & all precautionary measures during

execution shall have to be kept in sufficient numbers and in good working condition at the

site of the work.

13. Special modes of the construction not adopted in general Engineering practice, if proposed

to be adopted by the contractor shall be considered only if the contractor provided

satisfactory evidence that such special mode of construction and completion of work to the

required strength and quality. Acceptance of the same by the Engineer in charge shall not

however, absolve the contractor from the responsibility of any adverse effect and

concordance of adopting the same in the course of exaction or completion of the work.

14. The contractor shall be responsible for observing the rules and regulation imposed under

the "Minor Mineral Act", and such other laws and rules prescribed by the Government

from time to time.

15. All necessary safety measures and precautions (incl. those laid down in the various relevant

Indian Standard) shall be taken to engrave the safety of men, materials and machinery on

the work and also of the work itself.

16. Quantity measured in the tender is approximate. It may increase or decrease looking to the

quantum of actual work for which no any claim shall be entertained by A.M.C.

17. Contractor shall have to execute extra item if required only after necessary permission from

18. The work in general shall be carried out as per standard specifications of the relevant items

to be executed & as per the instruction of Engineer in charge & as per the guidance of

AMC's Consultant for this project.

19. The general terms & conditions of the contract shall be applicable & shall be binding on

the contractor. The contract agreement shall have to be executed between AMC & the

agency to which work is awarded for execution.

20. The time limit shall be reckoned after next day from the date of issue of the written work

order to the contractor after fullfillng the formality life SD & Agreement. No time

extension will be granted under any circumstances.

21. In case of any ambiguity in specifications mentioned in this tender, the interpretation given

by Additional City Engineer /Dy.M.C of A.M.C. will be final and binding to the

22. The contractor shall take no advantage of any apparent error or omission in drawing or

specification and the Engineer -in-charge shall make such corrections and interpretations as

necessary to fulfill the intent of the plants and specifications.

23. The quantities of items in BOQ (Bill of Quantities) may vary in case of necessity arises.

24. All prevailing taxes/duties chargeable by State Govt./Central Govt. and the Municipal

Corporation. will be payable by the contractor.

25. No any kind of price rise / price escalation / price variation for cement , steel or labour

26. Contractor is requested to see the site physically before tendering. He is also requested to

quote the rates keeping in view of all the points mentioned in relevant pages of tender

27. Water Supply: The contractor shall arrange at his own cost, a suitable supply of piped

water for the construction of the works and provide a satisfactory supply of potable water

for drinking, washing, sanitation and cleaning down. The contractor will be responsible for

all the costs where applicable of connection, meter installation, water consumed, water

required for testing purposes, disconnection and the laying, maintenances and ultimate

removal of any distribution system around the site.

28. Electricity: Electric supply will be made available at the site by the Contractor and the

contractor must make his own arrangements with the Corporation and Electricity Supply

Authorities and with other contractors to connect and to take a supply from such services,

paying all costs in connection therewith.

The Contractor shall be entitled to use supply Electricity as may be available on the site for

purpose of the work and shall pay such charges as is fixed by the appropriate supply

In case there is any delay in supply of power site of any interruption or fault in the power

during the work. No compensation shall be paid for idle labor staff, machineries and for

use of diesel operating sets etc. as the case may be.

29. Tenders shall submit all the valid/certified documents in support of their initial/eligibility

criteria mentioned above along with the bid. They shall have also to submit the income tax

clearance certificate and solvency certificate.

30. No advance such as secured advance machinery advance, mobilization advance or

materials advance will be given.

31. The contractor shall get the electrical works executed through the authorized Government

approved licensed electrical person or firm in appropriate category in accordance to

contractual provisions.

32. The electrical works shall be carried out strictly in accordance with the directives issued by

Engineer in charge.

33. Contractors shall not have any dispute or claim for any kind of compensations

(i) If the quantity stipulated in the tender items varies or the scope of work changes &

thereby total amount of work increases/ decreases.

thereby total amount of work increases/ decreases.

(ii) If the work gets delayed/ postponed for some administrative/ technical decision

34. In case of any dispute, decision of Municipal Commissioner shall be final and binding on

the contractors.

35. Tenders which do not fulfill all or any of conditions or are submitted incomplete in any

respect will be rejected. Municipal Commissioner reserves the right to increase/decrease

the scope of work. No any claim to that effect shall be entertained. The Municipal

Commissioner also reserves the right to reject any or all the tenders without assigning any

reason thereof.

36. The contractors are requested to quote their rates considering above tender conditions.

37. The contractor shall have to paid balance Security Deposit within 15 days from the date if

issue of Letter of Interest (LOI). And after paying the balance S.D. the time limit will be

started & Execution of Agreement to be done than after.

In case of delay in paying balance S.D. by more than 15 days penalty at the rate of

0.01% of sanction tender amount per day will be deducted from the Bill.

Eventhough in special case, If work is not started because of monsoon or any other

special reason (like site is not available), after evaluation of situation the actual date of

starting of work will be consider after approval of Dy.M.C. (South zone)

38. The Contractor shall not claim for increase or decrease in the quantity of the item or the

39. The payment shall be made as per the A.M.C policy for the work done by the contractor.

40. Conditional tenderes will not be accepted.

41. The Contractor must be followed the rules and regulations for COVID-19 as per guidelines

published by WHO/ Center government/State government /Ahmadabad municipal

Signature of contractor with seal Additional City Engineer (S.Z)

Date Ahmedabad Municipal Corporation

QUALIFICATION INFORMATION

1. The information to be filled in by the Bidder in these statements & supporting documents submitted

in physical form will be used for the purpose of pre qualification.

2. All statements given here under shall be submitted by bidders on their original letter pads only with

stamp of firm of bidder and sign of the bidder.

3. Photocopy of any statements shall not be considered as valid document.

4. Information / Details to be submitted by the Bidders in the Performa mentioned under Statement.

All the documents submitted in the support of these statements shall be duly attested and certified true

1. I/We hereby declared that I/We am/are not partner(s) blacklisted or connected with firm blacklisted

by AMC,Government of Gujarat,Ministry of Road Transport & Highways/NHAI.

2. The I / We also hereby certifies that our firm M/s ________________________________has

neither abandon any work in India nor rescinded any contract awarded to us during last five years prior to

the date of this bid.

3. At present I/We am/are registered as approved contractor (s), firms in any state, CPWD / MES /

4. We, the partners/owners of this firm, hereby give an undertaking that we are jointly and severally

responsible to meet all the liabilities ever and above the business of this firm and make good the above

financial loss sustained by the Amdavad Municipal Corporation as a result of our abandoning the works

entrusted to us.

5. I /We hereby certify that all the statements made in the required attachments are true and correct.

6. The I / We undersigned hereby authorise(s) and request(s) any bank, person, firm or corporation

to furnish pertinent information deemed necessary and requested by the Department to verify this

statement or regarding my (our) competence and general reputation.

7. I /We hereby declare that I / We understand and agree that further qualifying information may be

requested, and I / We also agree to furnish any such information at the request of the AMC within the

prescribed time.

8. I / We further declare that my / our near relatives are not working in AMC as an Addl. C.E., Dy.

C.E., A.C.E., A.E., and T.S. as on today.

(Signed by an Authorized Representative of the Firm)

Name of the Representative

1. I / We hereby declare that I / we have visited the site and fully acquainted myself / ourselves with

the local situations regarding materials, labour and other factors pertaining to the work before submitting

this tender. I/We certify that I/We have inspected the location of the proposed work before quoting my/our

2. I/We have also inspected the quarries and borrow areas and satisfied myself/ourselves regarding

the quality, quantity, availability, and transport facilities for earth, stone, bricks, and, cement etc. through

the network of available roads and path ways required for the work.

3. I / We hereby declare that I / we have carefully studied all the terms and conditions of contract,

specifications mentioned in the tender documents and I / we do agree for compliance with the same

4. I/We shall execute the contract agreement with the AMC after award of work and before start of

(Signed by an Authorized Representative of the Firm)

Name of the Representative

APPLICABILITY OF PROVIDEND FUND AND MISCELLANEOUS PROVISIONS ACT

Successful bidder i.e. the agency whose tender is accepted by the AMC shall have to comply the

necessary formalities under the employees provided fund and Miscellaneous Provisions Act, 1952 as

Contributory Provident Fund Scheme is applicable to laborers engaged in construction activity and shall

have to submit proofs regarding deduction of provident fund and other dues and depositing the same with

government department under the act and the scheme regularly on monthly basis failing which no running

/ final bill payment will be made by the AMC to the contractor in any circumstances.

A certificate to the above effect has to be given by the contractor as under.

Declaration of Depositing Provident Fund contribution

This to certify that we have deducted the employees’ P.F. and deposited the same along with

employer’s contribution towards provident fund on labour charges / wages paid by us to the laborers

with Provident Fund Authority under our Provident Fund Code No.___________

We produce herewith the copies of the challans for the provident fund deduction and contribution

deposited as mentioned above.

(Signed by an Authorized Representative of the Firm)

Name of the Representative

To be notarized by Notary

FORM OF BANK GUARANTEE

(hereinafter called the Tenderer) is desirous and preferred to tender for works in accordance with

the terms and conditions of tender for the work of

1 .Therefore. We hereby affirm that -we are guarantors on behalf of the Tenderer up to

(in figures) and we undertake to pay to Municipal Commissioner, Ahmedabad Municipal Corporation,

A'bad specified up to his first written demand, without demur without delay and without the necessity of a

previous of judicial or administrative procedures and without the necessity to prove to the Bank the

defects or short comings or debits of the contractor any sum within the limit of

2. We further agree that the Guarantee herein contemned shall remain in full force and effect during the

period that would be taken for the acceptance of tender.

However unless a demand of claim under this guarantee is made on its in writing on or before the

(Date to be specified will not he less than 180 days from the stipulated date of receiving the tender) we

shall be discharge form all liabilities under the guarantee thereafter.

3. We undertake not to revoke the guarantee during it currency except with the previous consent of the

Municipal Commissioner, Ahmedabad Municipal Corporation, A'bad in writing.

4. We lastly undertake not to revoke the guarantee for any charge in constitution of the Tenderer or of the

5. The contractors shall have to furnish income tax clearance certificate before his tender is accepted and

intimate assessment number and ward under which he is assessed.

6. Copies of certificate as regards previous experience, if any, must accompany the tender.

Signature of Contractor Add.C.E (S.Z) Dy. Municipal Commissioner (S.Z)

Date Ahmedabad Municipal Corporation

TENDER DECLARATION FORM

The Deputy Municipal Commissioner,

South Zone, Ahemedabad

Name of Works: - RCC Road construction and Paver Block Installation and other necessary work

as per requirement inside Kankaria Lake at maninagar ward south zone (ARC)

I/We the undersigned have carefully gone through and clearly understood the Tender documents

for the above work. I/We have satisfied myself/ourselves as to the location of site, examined drawings.

I/We have visited site & fully acquainted with local situations regarding materials, labours & others

factors pertaining to work before submitting tenders.

I/We do hereby offer to execute and complete the whole of the work within the time specified all

in accordance with the specification, designs, drawing and instruction in writing referred to in the said

document and with such materials as are provided for, at the respective rates which I/we have quoted in

the schedule-B or at such other rates as maybe fixed under the provisions of these conditions. In the event

of this tender being accepted I/We agree to enter into an agreement and when required and execute the

contract, according to your fom1 of agreement as or in default where of I/we bind myself/ ourselves to

forfeit the "Earnest Money Deposit."

I/We understand that if I/WE shall not enter in agreement within ten days or decided by AMC

from the date of receipt of letter of acceptance, you will forfeit the earnest money paid by me/us and take

necessary action as deemed fit.

I/We have enclosed a DEMAND DRAFT or PAY ORDER as an “Earnest Money Deposit", for the

sum as mentioned in tender notice, the full value of which is to be absolutely forfeited to the Employer If

I/We fail to commence the work specified. Otherwise the said sum shall be retained, by the Employer as

on account of such. Security) ' Deposit'.' as provided for in the aforesaid documents.

I/We agree not to employ sub-contractors other then those that may be approved in accordance

with Conditions in the aforesaid documents.

I/We understand that you are not bound to accept the lowest or any tender which you may receive.

I/We am/are bound to execute the job if the work order is issued within 120 days from the date of

opening of the tender.

I/We agree to pay the Government income-Tax, Sales-Tax (Central and State) ,Sales Tax on work,

octroi duties and other prevailing Government taxes/charges on such items on which the same are leviable

and therates quoted by me/us are inclusive of the same.

Yours faithfully

Signature of the contractor

ybœtJtœ BGþrlrmvj ftuvotuhuNl

ÆÂûtKÍtul - Esluh Ftðþ

1. mbgbgto>t ykdu yuj.ytu.ytR. ytÃgt ctœ 10 rœJm mw^ebtk sÁhe me¾gtuhexe rzvtuÍex

Che ðgth ctœ&e dKJtbtkk ytJNu. <ubs ðgth ctœ Jfo ytuzoh R~gw &gu&e mbtg bgtoœt NY

&guje dKtNu. <&t <u mt&u fhthvºt fhJtltu hnuNu. ylu <u bwsc ftb NÁ fhJtle <theF

dKJtbtk ytJNu. yuj.ytu.ytR. ytÃgt ctœ me¾gtuhexe rzvtuÍex ChJtbtkk rœl -15 fh<tk

J^w rJjkc ltk rfMmt btk <ubs Jfo ytuzoh ytvu&e ftb NY fhJtbtkk rJjkc &gu&e «r<rœl bkswh

xuLzh hfbltk 0.01 % juFu vulÕxe cej btk&e ftvJtbtk ytJNu. <ub A<tk rJrNÐ rfMmt btk

atubtmt ltk fthKu y&Jt yrlJtgo fthKtumh ftb NÁ &R Nfu <ub l ntug <u rfMmt btk

gtuøg<t aftme zu.Bgw.frb©h (œ.Ítul) le bkswhe bu¤Je ftb NÁ fhJtle <theF dKJtbtk

2. xuLzh Jujezexe 120 r>Jm Mþ^ele hnuNu.

3. xuLzh Ch<e JF<u yluoMxble ChJtle hnuNu.

4. S.yum.xe. «J<obtl œh «btKu yjd&e awfJJtbtk ytJNu. xuût fu yLg ftuE vK mhfthe

fhJuht ChJtle sJtc>the ftuLx[tfxhle hnuNu.

5. htsg / fuL÷ mhfth©elt JF<tuJF<lt ftg>t Bþsc su ftuE hfble fvt< fhJtle &Nu <u

bwsc ftuLx[tfxlt cejbtk&e fvt< fhJtbtk ytJNu.

6. juch JuÕVuh Vkz btxu ntjbtk htsg mhfth©eyu fhuj nwfb Bþsc 1% (yuf xft) hfb

cejbtk&e ftve juJtbtk ytJNu.

7. bxehegj xuMxekdltu xuMxekdltu FhuFh &guj Fao ftuLx[tfxh©e vtmu &e Jmwj fhJtbtk

8. ftb ytv<e JF<u su <u ftuLx[tfxhLþk hSMx[uNl ægtlbtk htFelu <ule bgto>tbtk ftb ytvJtbtk

9. yt xuLzh su <u Jdolt btLg gtœe lt ftuLx[tfxhtu Che NfNu. dJobuLxlt btLg ftuLx[tfxhu

y.BGþ.ftuvotu.btk btLg ftuLx[tfxhtu le gtœebtk hSMxuNl fhtJJtLþk hnuNu.

10. yt Wvhtk< y.BGþ.ftuvotu. lt slhj ftuLx[ufx fLzeNl ylu xuLzhle Nh<tu ck^lf<ot hnuNu. su

BGþrl.ftuvtuohuNl Juc mtEx www.ahmedabadcity.gov.in Wvh Bþfuj Au.

11. ftuLx[tfxh lu vubuLx - hl´dcej BGþrl.ftuvotu.lt su <u atÕþ mbglt mhfGþjh Bþsc fhJtbtk

12. Nh<e xuLzh MJefthJtbtk ytJNu lrn.

13. xuLzh MJefthÔþ, h> fhÔþ, ftulu ytvÔþ ylu fgt CtJ&e ytvÔþ <u ykdu zu.BGþrl.frbNlh©eltu

rlKog ytFhe hnuNu.

14. œhuf ytExbltk MvuNeVefuNl ftuvtuohuNlltk bkswh &guj MvuNeVefuNl Bþsc <&t RLzegl

MxtLzzo ftuz ytuV «ufxem ltkk btLg ^tht ^tuhKtu Bþsc hnuNu ylu zu.mexe yuLSlegh©eltu

rlKog ytFhe hnuNu. Jtuxh´d fhJtbtk lrn ytJu fu >hhtus J^thtltu zucheÍ WvtzJtbtk lrn

ytJu <tu ftuLx[tfxhltk Fauo ylu òuFbu Jdh ltuxemu Jtuxh´d fhtJJtbtk <&t zucheÍ WvtzJtbtk

ytJNu ylu cejbtk&e hfb ftve juJtbtk ytJNu.

15. yufe JF<u yuf fh<tk Jæþ søgtytuyu ftbNY fhJtltu Jfoytuzoh b¤u <tu ftb yuf mt&u s yuf

s c<tJuj søgtyu fhJwk vzNu. yuf ftb ÃþÁ &tg vAe cesw ftb NY fheyu <uÔþk atjNu lrn.

16. atÕþ ftbu ftuEvK mrJom jtEllu LþfNtl l &tg <u he<u ftb fhÔþk vzNu, òu ftuE mrJom jtEl

lu LþfNtl &Nu <tu <ule mkÃËKo sJtcœthe (òlbtjle) ftuLx[tfxhle vtu<tle hnuNu. mtEx vh

ftb œhBgtl bswh fu sl<t lt ftuE btKmlt òlbtjlu lwfNtl &tg <ule sJtcœthe

ftuLx[tfxhle hnuNu. vtujem Vhegt> &tg <tu <ule sJtc>the vK ftuLx[tfxhle hnuNu. CuFz ^me

l vzu <ule sJtc>the vK vtujem Vhegt>btk ftuLx[tfxhle hnuNu. CuFz ^me l vzu <u btxu

mjtb<elt vdjtk (suJt fu >tuhzwk ctk^e bsqh Ftztbtk W<thJt, mtuh´d ylu Mx[x´d fhJt

rJduhu) je^t Jdh bsqhlu Ftztbtk W<thNu <tu ftuLx[tfxh s vtujem Vhegt>btk sJtct>h hnuNu

ylu BGþrl.ftuvtuohuNlltu ftuEvK MxtV ytlt btxu sJtc>th hnuNu lrn. ytxÕþk mbSlu s xuLzh

ChÔþk. Btswhtultu rJbtu vK W<thtJJtu.

17. juch yufx «btKu <ubs Bgw. frb§h©eltkk vrhvºt lkch 81 <t.26.02.2015 bwsc <btb

juch / bsqhtulwk dwsht< rcÕzekd yuLz y^h fLMx[[fNl Jfombtkk VhSgt< hSMx[uNl fhtJJt

ykdu ybj fhJtltu hnuNu <&t fuxjt juch jtJNtu <u vK sKtJJtLþk hnuNu. juch yufx «btKu

ftgoJtne lrn &E ntug <tu <u btxu ftuLx[tfxh mkÃËKovKu sJtc>th hnuNu. ylu <ulu vubuLx

ytvJtbtk ytJNu lrn <ubs ct¤ bswhtulu ftb Wvh htFe NftNu lrn. <ubs JF<tu JF<

Bgw. frBNlh©e îtht fhJtbtkk ytJuj mh¾gwjhtule Nh<tu ftuLx[[tfxhlu ckk^l f<to hnuNu.

18. ftuEvK ftgœtfeg jexeduNl ybœtJtœ Nnuhle ftuxobtk hnuNu.

19. ftuE fthKmh òu ftuLx[tfxhlu ftb l ytve Nftg <tu <u ykdu ftuLx[tfxh ftuEvK «fthltu

LþfNtle- J¤<hltu n¬ >tJtu fhe NfNu lrn fu ftg>tfeg ftgoJtne yt ykdu &E NfNu lrn.

xuLzh bkswh &gtltu y&o ftb ytve s >uJtLþk Au <uJtu &E NfNu lrn.

20. ytuVh y&Jt xuLzhbtk œNtoJuj ytRxbltu sÚ&tu mkCrJ< sÚ&tu Au subt atjw ftb œhBgtl

VuhVth &Jtle N¾g<t hnuje Au.

21. M&¤ vrhÂM&r< / sYhegt< Bþsc ftb fhtJ<t xuLzhbtk sKtJuj fJtuLxexebtk J^ Dx &Nu <tu <u

ykdu ftuLx[tfxh îtht ftuEvK «fthle J^thtle ltKtkfeg btkdKe fhe NfNu lrn. ylu ftb

ytuAw &tg <tu ftuLx[tfxhle J¤<hle btkdKe MJefthJtbtk ytJNu lrn.

22. mtEx vh jtJJtbtk ytJuj btjmtbtl hesufx fhJtbtk ytJu <tu ðþhk< r>l-1btk vh< jE

sJtltu hnuNu. yLg&t ftuvtuohuNl îtht <u hesufx btjltu rlftj fhe >uJtbtk ytJNu ylu <ule

LþfNtlele sJtc>the ftuLx[tfxhle hnuNu.

23. su ftuLx[tfxh vtmu bswhtultu rJbtu, ydtW&e W<htÔgtu ntug <ublu «t^tLg ytve ftb ytve

24. bsqhtu fu htn>theytulu ftuEvK «fthltu yfMbt< &tg <tu <ule vtujem ftgoJtnele fu juch

yufx bwscle ftgoJtnele sJtc>the yb.BGþrl.ftuvtuo.lt fboatheytule ftuEvK he<u hnuNu

lrn.btºt ftuLx[tfxh s yt btxu sJtc>th hnuNu. bswhtulu dbçËx, nuÕbux nt&ltk btuò rJduhu

ftuLx[tfxhu VhSgt< ytvJtltk hnuNu. bswhtu <&t MþvhJtEÍ fu Bþft>bltu rJbtu vK W<thJtltu

VhSgt< hnuNu. juch yufx Bþsc ltuk^Ke fhtJe <ult rlgbtuLþk vtjl fhJt ftuLx[tfxh

ck^tguj hnNu. ct¤ bswhtu htFe NftNu lrn.

25. bsqhtu fu htn>theytulu ftuEvK «fthltu yfMbt< &tg <tu <ule vtujem ftgoJtnele fu juch

yufx bwscle ftgoJtnele sJtc>the yb.BGþrl.ftuvtuo.lt fboatheytule ftuEvK he<u hnuNu

lrn.btºt ftuLx[tfxh s yt btxu sJtc>th hnuNu. bswhtulu dbçËx, nuÕbux nt&ltk btuò rJduhu

ftuLx[tfxhu VhSgt< ytvJtltk hnuNu. bswhtu <&t MþvhJtEÍ fu Bþft>bltu rJbtu vK W<thJtltu

VhSgt< hnuNu. juch yufx Bþsc ltuk^Ke fhtJe <ult rlgbtuLþk vtjl fhJt ftuLx[tfxh

ck^tguj hnNu. ct¤ bswhtu htFe NftNu lrn.

26. rcÕz´d ftble ytExbtu btxu - slhj xuflefj MvuNeVefuNl ytuV rcÕz´d Jfomle çþf Bþsc

yLþmhJtltk hnuNu. Mt>h ÃþM<eft øþsht< çþf Mxtumo 20-ce, zeMx[ef Ntuv´d, mufxh-21,

dtk^eldh&e b¤e hnuNu. su Juc mtEx www.ahmedabadcity.gov.in Wvh Bþfuj Au.

27. bxehegj fu ceò xuMx´d hevtuxo ftuLxtfxhu vtu<tlt Fauo ftuvotuhuNl sKtJu <u søgtyu fhtJJtlt

hnuNu. yt ykdultu mkÃËKo Fao <&t Bgwrl.MxtVlu juctuhuxhe Mþ^e <&t buLGþVufah´d søgt Mþ^e

jtJJt -jE sJtltu Fao vK ftuLx[tfxhu CtudJJtltu hnuNu.

28. btj su <u Mxtumo Wvh y&Jt mtEx Wvh jtuftulu lz<h l &tg <u he<u MËalt Bþsc W<thJtltu

<ubs dtuXJJtltu hnuNu.

29. òu BGþ.yuLSlegh´d MxtV sKtJu <tu ftuLx[tfxhu atÕþ ftbu mtEx Wvh zeÍexj fubuht&e ftb

atÕþ &gt vnujt, atÕþ ftbu <&t ftb ÃËKo &gtltk Vtuxtud{tVm BGþrl.yturVmbtk ytvJtltk hnuNu

<u rmJtg ftbLþk vubuLx fhJtbtk ytJNu lrn òu MxtV MËalt ytvu <tu fubuhtbtk&e ftuBÃGþxhbtk

Vtuxt x[tLmVh fhe ytvJtlt hnuNu. yt ykdu ftuE vK J^thtltu Fao ytvJtbtk ytJNu lrn.

30. ftuEvK fthKmh xuLzh h> fhJtbtk ytJu <tu ftuLx[tfxh <u ykdu ftuEvK «fthltu n¬ >tJtu fu

J¤<hle btkdKe fhe NfNu lrn. yt Nh< MJeftgo ntug <ubKu s xuLzh ChÔþk.

31. bxehegÕm suJt fu hu<e, #xtu, mebuLx, vtEv, rJduhu MxtLzzo bxehegÕm MvuNeVefuNl «btKult

jtJJtlt hnuNu. sgtk ftuE atuFJx l &E ntug ðgtk ytE.yum.ftuz «btKu bxehegÕm jtJJtLþk

<&t xuMx´d fhtJJtLþk hnuNu. <ubs ftuLx[tfxhu muBvj yu«wÔz fhtÔgt ct> ftb NY fhtJJtLþk

32. yt xuLzhbtk òu ftuE ytExb hne dE ntug <tu <u atÕþ yum.ytu.yth.btk&e juJtbtk ytJNu ylu

òu yum.ytu.yth.btk ytExb l ntug <tu btfuox huEx&e huEx yultjemem fhe su CtJ Ft<t

<hV&e ytvu <u ftuLx[tfxhu juJtltu hnuNu. yt mbSlu s xuLzh ChJtLþk hnuNu. J^tht le

ytRxb btk ftuLx[tfxhle btkdKe Bþsc CtJ b¤Nu lrn.

33. atÕþ ftb >hBgtl «tuxufNlle mkÃËKo sJtc>the ftuLx[tfxhle hnuNu subtk vevzt, >tuhzt,

CgMËaf ctuzo, jtj xul , cuhefuxekd xuv, ÃjtMxef vèe, rJ. ftuLx[tfxhu jtJJtLþk ylu

mtaJJtLþk hnuNu. ylu ftuEvK yfMbt< &Nu <tu <ule mkÃËKo sJtc>the ftuLx[tfxhle hnuNu.

34. MxtV MËalt ytvu <tu mtEx Wvh zuEje «tud{um hSMxh ftuLx[tfxhu htFJtLþk hnuNu. >hhtus

ytme.mexe yuLSlegh©ele <ubtk mne juJtle hnuNu, <ubtk >hhtus ftb fh<t bswhtule mkÏgt,

fhuj ftbdehe <&t yr^ftheytuyu ftb Mþ^thJt fu «tud{um J^thJt ltuk^ fhuj ntug <tu <uLþk

ftuBÃjtgLm ytvJtLþk hnuNu ytJe ltuk^ltk sJtc l &gu fu <u «btKu M&¤ Wvh ybj l &gu

ftuLx[tfxhlu vulÕxe fhJtle m•tt yuze.mexe yuLSlegh©elu hnuNu <u ykdu ftuLx[tfxh ftuE

Jtk^tu jE NfNu lrn.

35. rlg< mbgbgto>tbtk ftb ÃþY l &gu&e xuLzh ¾jtuÍ bwsc ctfe ftbltkk 10.00% juFu vulÕxe

BGþrl.ftuvtuohuNllu åþfJJtle hnuNu.

36. xuLzh le yt Nh<tu ce - 1 Vtubobtk sKtJuj Nh<tulu ytuJhYj fhNu.

Wvhtuf< <btb Nh<tu <&t rlgbtu buk ft¤SÃËJof Jtkauj Au ylu blu fçËj bksqh Au.

ftuLx[tfxhle mne - rm¬tu yuze.mexe yuLSlegh

btuctEj lkch mt&u (œrûtKÍtul)

yufhthlwk Vtubo

(1) nwk/ybu yt&e yufhth fhwk Awk/fheyu Aeyu fu yt xuLzh hsw fh<tk vnujtk buk/ybu M&¤le bwjtft< je^e Au ylu

ftblu jd<t btjmtbtl, bswhe ylu ceS ctc<tulu jd<e M&trlf vrhrM&r<le ò<-btne<e bu¤Je Au.

(2) nwk/ybu yt&e yufhth fhwk Awk/fheyu Aeyu fu yt ftuLx[tfxhtule Nh<tu rJd<tu ylu xuLzhlu jd<t >M<tJustu

ft¤SvwJof yÇgtm fgtuo Au ylu <u bwsc <ultu ybj fhJt mkb< Awk/Aeyu.

ftuLx[tfxhle mne - rm¬tu yuze.mexe yuLSlegh

btuctEj lkch mt&u (œrûtK Ítul)

" ybœtJtœ BGþrlrmrvj ftuvtuohuNl”

œrûtK Ítul- Esluh Ftðþ

vtKe, z[ulus, vuJ´d, heEMxuxbuLxlt ftuLx[tfxhu Ftm JtkaJt ylu ægtlbtk htFJtle ctc< leau Bþsc Au.

" yt ftblt œhuf ytExblt sÚ&tbtk ~ËLg &e cMmtu xftle JD^x &Jt mkCJ Au. ftuE ytExbltu CtJ J^thtu

ytvJtbtk ytJNu lrn. yBþf søgtyu swlt vÚ&h s VheJth heEMxux fhJtlt &Nu. <uJe œhuf ytExbbtk J^^x &tg fu

ytExb yufÍefGþx l &tg <uÔþk vK clNu. ytlt btxu ftuEvK «fthle J¤<hle btkdKe fhJtle hnuNu lrn fu CtJ

J^thtu, vK ytvJtltu &Nu lrn. <ult btxu Ãþh<tk mt^ltu ylu bsqhtu ntug, yuf mt&u yluf søgtytuyu ftb fhJtle ûtb<t

ntug <ubKu s rJathelu xuLzh ChÔþk. bsqhtu l&e fu dtbzu s<t hÌtt Au fu ntu¤e, lJhtºte, rœJt¤e, jøl meÍl fu yLg

<nuJthtubkt fu «mkdtubtk bsqhtu ytJ<t l&e <uJt fu ceò ftuEvK cntlt nuX¤ ftb ck^ htFe NftNu lrn yLg&t htuslt

Yt.250.00le J^thtle vulÕxe ftb ck^ hnu fu MËalt fh<t ytuAt bsqhtu ytJu <ulu je^u fhJtbtk ytJNu.”

ftuLx[tfxhle mne yuze.mexe.yuLS.

rm¬t ylu btuctEj lkch (œrûtK Ítul)

AHMEDABAD MUNICIPAL CORPORATION

ENGGNIERING DEPARTMENT

GENERAL SPECIFICATION

Time limit for the work shall be as per tender notice after the order to start the

works. Progress of work should be in proportion to time limit. The details of reinforcement

of R.C.C. work shall be as per design and instructions of Add. City Engineer and his order

will be considered final.

The contractor shall have to maintain account of steel, cement and other materials

that may be brought by him on site. This account shall be regularly maintained and kept

open for inspection by Municipal Staff. Watering of all the items shall be as per

instructions otherwise no payment shall be made to contractors. Mixing of concrete shall

be done by concrete mixer machine. Arrangements of binding vibrator for R.C.C. works if

required shall have to be made by the contractor.

The contractor shall be remain responsible for Workmen’s compensation if any

accident. The contractor shall arrange for barricading at night and arrangement of Pagi at

night to direct the traffic. He shall be responsible for any damage to public. If any incident

happen, during the execution of work. In case of dispute for unseen or overlooked items

the decision of the Dy. City Engineer shall be final. The contractor shall have to give site

clean of all rubbish during the work and at the time of completion of work and hand over

the site with final finishing of the work as directed. All the rejected materials shall be

removed from site within 24 hours by contractor at this risk and cost. Debris shall have to

cart daily from site.

For mixing mortar either for masonry or for plaster or for any other purpose

contractor shall have to prepare through of bigger size and mix the mortar in the required

proportion. In on case he shall be allowed to mix the mortar either on floor or any finished

surfaces. The contractor shall have to make his own arrangement for water required for the

If any extra item crops up during the progress of work the same shall be carried out

by the contractor and he shall be paid at the rate fixed by Add.C.E. as per the rate analysis

based on latest SOR or if item is not available in SOR than based on current market rates.

In case of extra item decision of Add. City Engg. shall remain final regarding rate.

If in the interest of the Corporation it is necessary to change either any site or the

design of the propose work the contractor shall carry out the same at his quoted rates

without charges any extra and the contractor will have to carry out the works and he will

be paid at the rate quoted by him. No claim for extra rate for subsequent changes in site

and design is entertained.

The cubical contents of the cement bag shall be taken as 1-20 cft. Per bag and the

contractors shall have to prepare the measures boxes according to this measure.

Octroi exemption passes shall not be given for any materials required for the work.

Contractor will be fully responsible for compliance of the various provisions under

contract Act. 1970 and the Rules framed the to under.

The tender for the work shall remain open for a period (120) days from the date of

opening of the tenders for this work and that the tenderer shall not be allowed to withdraw

on modify the offer on his own during the period. If any tenderer withdraw or makes any

modifications or addition in the terms and conditions of his tender not acceptable to the

Municipal Corporation the Municipal Corporation shall without prejudice to any right or

remedy be at liberty to forfeit in full the said earnest money and black list the contractor.

If work is not started within specified time limit i.e. within ten days from the date of

order to start the work the penalty of the 0.01% tender Amount per day of delay of start

shall be recovered separately from the immediate bills payable to the contractor.

Contractor has to make his own arrangement for procurement of steel and cement.

Contractors should note the following conditions carefully:-

i) Conditional tender shall not be accepted.

ii) All tenders are to be submitted in duplicate without which the tenders are liable to be

iii) In case of tender downloaded from website, tender fee & EMD should be submitted

in form of demand draft.

iv) Condition of Form - B1 only Standard Specification of material & code of practice

will be applicable. Form B1 can be is available in website. Specification shall be as

per ' R & B Dept. - Govt. of Gujarat booklets of Building Works & and Road

Works Specifications published by Gujarat Book Depot, Sector-21. Gandhinagar.

Other techinical condition will be applicable as per tender condition only.

Contractor's signature & Stamp ADD CITY ENGINEER

Mobile No.:- (South Zone)