Interior renovation, refurbishment including MEP works for Port Bhavan for Mumbai Port Authority (MbPA) at Shoorji Vallabhdas Marg, Ballard State, Mumbai-400001

GRAND TOTAL 33,42,66,903.31

3 6.47 Providing and laying Autoclaved Aerated concrete(AAC) blocks masonry with 150mm to 300 mm thick Cu.m 8,333.65 100.00 8,33,365.00

with Grade-1 AAC blocks of density 551 to 650 kg/cum conforming to IS:2185 (Part 3) in super

structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved

block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge.

(The payment of RCC band and reinforcement shall be made for seperately).

4 PWD SSR Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C Rmt 70.62 5,000.00 3,53,115.00

2022-23 members and brick work, of approved quality including fixing mesh in position by necessary

32.26 drilling in concrete /B.B.masonry and or tying by binding wire etc. complete.

5 PWD SSR Providing and applying one pack bonding coat between concrete members like RCC slabs, columns, Sq.m 66.91 9,648.00 6,45,509.09

2022-23 beams, chajjas, pardis etc and cement mortar plaster of approved make & approved by Engineer in

50.09 charge. Clean the concrete surface thoroughly to remove dust, dirt, grime, deshuttering oils and rub

down to a clean surface. Apply bonding coat of approved make & approved by Engineer in charge by

spray on the entire concrete surface. Provide a lean cement - sand dash coat over the same. Allow the

dash coat to set for around 24 hours. Further plastering as per specifications can continue.

6 NS- 1 Providing and applying factory manufactured ready mix cement plaster of approved make, 12 mm Sq.m 527.50 9,648.00 50,89,320.00

average thickness, consisting of free flowing granular grey premixed material with selective processed

sand, mixed with clean water in proportion as recommended by manufacturer (approx. 6.8 to 7.6 litres

per 40 kg bag), having compressive strength not less than 8 MPa, flexural strength not less than 2 MPa,

pull out bond strength not less than 0.3 MPa, including surface preparation, hacking/raking of joints

wherever required, scaffolding, mixing, application, finishing true to line, level and plumb, curing for

minimum 3 days, and all labour, materials, tools & plants complete as per manufacturer’s

specifications and direction of Engineer-in-Charge.

7 13.78 Providing and applying 12 mm thick (average) premixed formulated one coat gypsum lightweight Sq.m 468.90 8,517.00 39,93,621.30

plaster having additives and light weight aggregates as vermiculite/ perlite respectively conforming to

IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven background such as bare brick/ block/ RCC

work on walls & ceiling at all floors and locations, finished in smooth line and level etc. complete.

8 NS- 2 Providing and applying factory manufactured ready mix cement plaster of approved make, 20 mm Sq.m 873.75 1,548.00 13,52,565.00

average thickness, consisting of free flowing granular grey premixed material with selective processed

sand, mixed with clean water in proportion as recommended by manufacturer (approx. 6.8 to 7.6 litres

per 40 kg bag), having compressive strength not less than 8 MPa, flexural strength not less than 2 MPa,

pull out bond strength not less than 0.3 MPa, including surface preparation, hacking/raking of joints

wherever required, scaffolding, mixing, application, finishing true to line, level and plumb, curing for

minimum 3 days, and all labour, materials, tools & plants complete as per manufacturer’s

specifications and direction of Engineer-in-Charge.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

13.37 White washing with lime to give an even shade : -

9 13.37.1 New work (three or more coats) Sq.m 39.05 500.00 19,525.00

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile -

Organic Compound ) content.

10 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre Sq.m 73.95 9,648.00 7,13,469.60

11 13.8 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and Sq.m 156.05 9,648.00 15,05,570.40

manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic -

Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

additional coats wherever required to achieve even shade and colour.

13 NS- 3 Providing and applying premium grade decorative interior texture paint of approved make, shade, Sq.m 640.20 10.00 6,402.00

colour and texture, over properly prepared, putty-finished and primer-coated surfaces, including

application of approved texture coating in the specified pattern/profile using suitable tools, rollers,

trowels or spray equipment as required, achieving uniform texture, colour, thickness and finish as per

approved sample/mock-up and manufacturer's recommendations; including all necessary masking,

protection of adjoining surfaces, preparation of texture material, application in required number of

coats/layers, levelling and finishing, touch-ups and making good minor surface imperfections,

complete with all labour, scaffolding/access arrangements, tools, tackles and incidental materials,

complete in all respects as directed by the Engineer-in-Charge/Architect.

13.47 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: -

14 13.47.1 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior Sq.m 171.10 10.00 1,711.00

primer applied @ 0.90 litre/10 sqm)

15 PWD SSR Providing and applying Texture plaster with finishing with texture material of approved make in Sq.m 778.09 10.00 7,780.92

2022-23 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness

32.32 or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the

surface, scaffolding etc. complete.

16 PWD SSR Providing and applying Elastomeric, Anti carbonation, Anti corrosive, UV resistant, Solvent based Pure Sq.m 646.76 9,648.00 62,39,921.18

2022-23 Aliphatic Acrylate System- on the exterior faces of Buildings Protection against ION penetration,

47.19 carbonation,UV radiations and wethering effect conforming to ASTM D 4541-02 having

Electrochemical impedance of 107 Ω and achieving dry film thickness of minimum 200 microns in a

primer coat followed by two top coats using brush or spray after complete cleaning & removal of oil,

grease or loose particles from the surface etc. complete

22.7 Providing and laying integral cement based water proofing treatment including preparation of surface

as required for treatment of roofs, balconies, terraces etc consisting of following operations:

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

(a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing

compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including

adjoining walls upto 300 mm height including cleaning the surface before treatment.

(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of

cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to

IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1

cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved

by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height

including rounding of junctions of walls and slabs.

(c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of

cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-

(d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand)

admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge

including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the

surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for

curing and for final test.“All above operations to be done in order and as directed and specified by the

Engineer-in-Charge :

17 22.7.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Sq.m 1,684.60 200.00 3,36,920.00

18 PWD SSR Providing waterproofing in W.C. and bath including brick bat coba in all position including providing Cu.m 8,194.10 20.00 1,63,881.97

2022-23 and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing

31.26 compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with

waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm

thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and

testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite

stamp paper including curing etc. complete.

19 PWD SSR Waterproofing Treatment to plastered surface of toilet & bathroom walls minimum up to 90 cm Sq.m 557.55 500.00 2,78,775.00

2022-23 (Dado) by using 2-(methoxycarbonyl)-1-propene-Butyl-2 propenoate (MPBP) based polymeric

52.23 waterproofing solution as approved by Engineer in charge. Clean the entire surface thoroughly and

over this prepared surface, apply three coats of 2-(methoxycarbonyl)-1-propene-Butyl-2 propenoate

(MPBP) based polymeric waterproofing solution as approved by Engineer in charge.While the 3 coat is

wet broadcast sand on the surface. Provide 20 mm thick cement plaster in CM 1:3 with one pouch of

330 grams of thorough blend of special cements, aldehyde based polymers, shrinkage compensating

agents as approved by Engineer in charge per 50 Kg bag of cement including all lead, lifts ,curing etc

complete. Acrylic Polymeric Waterproofing Coating for Concrete and Masonry should have following

minimum properties:

1. Elongation % (ASTM D412-2016): @ 100%

2. Tensile Strength N/mm2 (ASTM D412-2016): 3.3

3. Specific Gravity: 1.02 ± 0.02

4. Total Solids (ASTM D1644-2012): 43.98

5. Hardness Shore A (ASTM D2240-2015): 82

It shall be applied as per manufacturer’s specification.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

20 22.22 Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures Kg 388.00 10.00 3,880.00

like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and

bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck , using

integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of

concrete) or higher as recommended by the manufacturer's specification in reinforced cement

concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e.

by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN

1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-

healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per

specification and the direction of the Engineer-in-charge. The product performance shall carry

guarantee for 10 years against any leakage.

22.23 Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment

to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior,

sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the

ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts

integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative

(internal) side with the help of synthetic fiber brush. The material shall meet the requirements as

specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared

with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side.

The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall

be carried out all complete as per specification and the direction of the engineer-in-charge. The

product performance shall carry guarantee for 10 years against any leakage.

21 22.23.1 For vertical surface two coats @ 0.70 kg per sqm per coat Sq.m 472.90 10.00 4,729.00

22 22.23.2 For horizontal surface one coat @1.10 kg per sqm. Sq.m 362.80 5,000.00 18,14,000.00

23 PWD SSR Providing and applying a base coat comprising of 1KilogramPolydee-MC and Sq.m 1,569.81 50.00 78,490.65

2022-23 1Kilogramfresh cement after wetting the surface followed by drying the surface for 2 days, apply

31.11 primer coat of TP-40 and after drying, applying Polydee-11 two component (mixing ratio 2 A : 1 B) )

Antibacterial food grade coating inside drinking water tank in two coats with time interval of minimum

8 hrs. covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete.

24 PWD SSR Providing and applying epoxy paint primer with middle coat and top coat to superstructure including Sq.m 861.11 1,000.00 8,61,105.00

2022-23 scaffolding etc complete.

11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry -

mixed with pigment to match the shade of the slab, including rubbing and polishing complete with

base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

26 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick Sq.m 2,354.70 3.00 7,064.10

cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment

to match the shade of the slabs, including rubbing and polishing complete.

27 8.6 Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss Sq.m 506.70 24.00 12,160.80

finish complete.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the -

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand

& manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system

and rubber mallet for placing the tiles gently and easily. (3mm spacer to be provided as per drawing

and nothing shall be paid extra for this)

11.41A.1 Double charge vitrified tile polished finish of size -

29 NS- 4 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the Sq.m 2,541.00 835.00 21,21,735.00

manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand

& manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse

sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying

of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system

and rubber mallet for placing the tiles gently and easily. (3mm spacer to be provided as per drawing

and nothing shall be paid extra for this) Size- 1200x1200 mm

11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size -

31 NS- 5 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), Sq.m 1,873.75 1,215.00 22,76,606.25

with water absorption less than 0.08% and conforming to IS: 15622, of approved brand &

manufacturer, in all colours and shade, in wall dado & Skirting laid with cement based high polymer

modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,

including grouting of joints (Payment for grouting of joints to be made separately). (3mm spacer to be

provided as per drawing and nothing shall be paid extra for this)

Size of Tile 600x600 mm

32 NS- 6 Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), Sq.m 2,856.55 31.00 88,553.05

with water absorption less than 0.08% and conforming to IS: 15622, of approved brand &

manufacturer, in all colours and shade, in wall dado & Skirting laid with cement based high polymer

modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,

including grouting of joints (Payment for grouting of joints to be made separately).(3mm spacer to be

provided as per drawing and nothing shall be paid extra for this)

Size of Tile 1200x1200 mm

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

33 NS- 7 Providing and laying Large Format Colour Body Sintered Surface Flooring using UNITERRA tiles/slabs of Sq.m 8,273.30 47.00 3,88,845.10

approved shade, texture, pattern and finish, size 1190 × 2400 / 2800 mm (or approved equivalent

large format as per design), 9 mm thick, colour body construction, manufactured using AI DIGI+

Technology and advanced sintered surface technology, having very low water absorption, high flexural

strength, excellent scratch resistance, stain resistance and UV stability.

The flooring shall be laid over an average 25–30 mm thick cement mortar bedding in CM 1:4 (1 cement

: 4 coarse sand), including preparation and dressing of base surface to required line, level and slope,

application of approved high-performance polymer modified adhesive suitable for large format

sintered slabs, laying, positioning, alignment, levelling, edge matching, mechanical handling, cutting,

trimming, tapping and adjustment to achieve true plane and uniform finish.

The item shall include treatment and filling of joints with approved matching grout, cleaning of finished

surface, protection during execution and handover, curing wherever required and execution complete

in accordance with manufacturer’s specifications, approved shop drawings and Architect’s

Rate shall include cost of all materials, labour, cement mortar bedding, adhesive, grout, cutting and

wastage, edge finishing, loading, unloading, transportation, lifting to all levels, tools & tackles,

machinery, scaffolding wherever required and all incidental works complete in all respects. .(3mm

spacer to be provided as per drawing and nothing shall be paid extra for this) (Tile basic rate : 350

34 NS- 8 Providing and laying Large Format Colour Body Sintered Surface DADO using UNITERRA tiles/slabs of Sq.m 8,084.60 51.00 4,12,314.60

approved shade, texture, pattern and finish, size 1190 × 2400 / 2800 mm (or approved equivalent

large format as per design), 9 mm thick, colour body construction, manufactured using AI DIGI+

Technology and advanced sintered surface technology, having very low water absorption, high flexural

strength, excellent scratch resistance, stain resistance and UV stability.

The Dado shall be laid over plastered surafce with application of approved high-performance polymer

modified adhesive suitable for large format sintered slabs, laying, positioning, alignment, levelling,

edge matching, mechanical handling, cutting, trimming, tapping and adjustment to achieve true plane

and uniform finish.

The item shall include treatment and filling of joints with approved matching grout, cleaning of finished

surface, protection during execution and handover, curing wherever required and execution complete

in accordance with manufacturer’s specifications, approved shop drawings and Architect’s

Rate shall include cost of all materials, labour, adhesive, grout, cutting and wastage, edge finishing,

loading, unloading, transportation, lifting to all levels, tools & tackles, machinery, scaffolding wherever

required and all incidental works complete in all respects.(3mm spacer to be provided as per drawing

and nothing shall be paid extra for this (Tile basic rate : 350 Rs/sq.ft)

35 R3-CS-CH- Providing and fixing Pattern tiles of 23-25mm thick Bharat Tiles or equivalent of Sq.m 9,503.72 2,872.00 2,72,94,683.84

27 approved colours and cut to shape of approved patterns & grinding edges filling

joints as per manufacturer's specifications and including 25 mm thick bedding

mortar,grouting,watering,curing,cleaning,polishing etc. complete as directed by the Architect. (Tile

basic rate : 375 Rs/sq.ft)

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

36 R3-CS-CH- Providing & Laying 20-25 mm thk Plain Bharat Tiles or equivalent cement tile for Rmt 7,041.06 1,422.00 1,00,12,387.32

29 border as per design. The border design to be broken up into 3-4 components in

different colours upto a maximum of 4 colours and pattern inserts indicated by

the architect as per drawing in cement mortar 1.5 to 3.5 cm cement : sand bed mortar of 36 grade

cement of ratio not leaner than 1:4 with a neat cement slurry on top, of approved thickness. Joints

should be as fine as possible and filled with matching cement mortar as directed by architects. (Tile

basic rate : 375 Rs/sq.ft)

37 R3-CS-CH- Providing and laying of Bharat Tiles or Equivalent make cement tiles skirting of Rmt 1,276.76 1,877.00 23,96,478.52

30 100mm ht. using Plain tiles (plain colour including all the range (dark, light or

premium) as available with the manufacturer) 17-20 mm thick. Item complete with 20-25mm thick

cement mortar 1:4 and finishing with 6mm groove at the junction between skirting and wall etc. Rate

to be inclusive of tile,storage,all duties and taxes applicable. (Tile basic rate : 375 Rs/sq.ft)

11.56 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well -

as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick

stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and

jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching

shade including rubbing , curing and polishing etc. all complete as specified and as directed by the

Engineer-in-Charge.

38 11.56.1 Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent Sq.m 4,481.30 70.00 3,13,691.00

39 NS- 9 Providing and laying Polished River washed Granite stone flooring in required design and patterns, in Sq.m 5,009.40 25.00 1,25,235.00

linear as well as curvilinear portions of the building all complete as per the architectural drawings with

18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse

sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment

of matching shade including rubbing , curing and polishing etc. all complete as specified and as

directed by the Engineer-in-Charge.

40 NS- 10 Providing and fixing polished River Washed Granite stone for treads and risers of staircases in required Sq.m 5,332.35 25.00 1,33,308.75

widths, lengths and profiles, including 18 mm thick granite stone for treads and risers, machine-cut

with rounded/chamfered nosing, anti-skid grooves on treads as per approved design, edge polishing,

cutting, dressing and moulding wherever required, laid over 20 mm (average) thick bed of cement

mortar 1:4 (1 cement : 4 coarse sand), jointed with cement slurry and pointed with white cement slurry

admixed with pigment of matching shade, including rubbing, curing, polishing, making openings,

cutting to shape, finishing exposed edges and all incidental works complete as per approved drawings,

specifications and directions of the Engineer-in-Charge.

8.10 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep -

and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter

and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and

finished smooth.

41 8.10.2 Granite Stone of approved shade Sq.m 4,051.85 3.00 12,155.55

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

42 16.90 Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm Sq.m 2,017.60 50.00 1,00,880.00

having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all

colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid

on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including

grouting the joints with white cement mixed with matching pigments etc. complete as per direction of

Engineer-in-Charge.

43 R3-CS-FL-88 TELEPHONE BLACK GRANITE WASH HAND Rmt 11,755.16 29.00 3,40,899.64

BASIN COUNTER : Providing and making wash basin counter in single piece of 18 mm to 20 mm thk.

Telephone Black granite 600 mm side fixed over 25 to 40 mm thk. Black Cuddappa, stand with type

construction,by making zari, in walls upto 75 mm deep & fitting the wall surface by C.M. 1:2 with

necessary moulding,profile cutting in granite and cudappa including making hole to receive pillar cock

for wash basin etc complete and as per detailed

44 PWD SSR Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 Sq.m 12,175.65 2.00 24,351.31

2022-23 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm

41.78 thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side

strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm

height and top granite of 75 x 40 cm including cutting, opening for sink of required size in

kadappah as well as granite etc. complete

45 PWD SSR Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba Sq.m 5,169.11 42.00 2,17,102.54

2022-23 White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and

33.35 staircases of approved colour and shade with full moulding and three grooved line for the treads on

bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing

and cleaning etc. complete.

46 PWD SSR Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown Sq.m 5,442.40 200.00 10,88,479.91

2022-23 granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including

33.68 filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc.

47 Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of Sq.m 275.41 2,519.00 6,93,764.09

11.48 organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling /

grouting and finishing complete as per direction of Engineer-in-charge.

48 NS- 11 Providing and fixing decorative metal inlay/insert of approved grade Stainless Steel (SS 316) , of Rmt 853.60 100.00 85,360.00

approved finish (mirror, brushed, matt, antique, PVD, hairline or as approved), width, thickness and

profile as per approved drawings, accurately cut, shaped and fixed flush with adjacent finished

surfaces using approved adhesive, mechanical fasteners and accessories wherever required, including

cutting grooves, alignment, polishing, cleaning, protection and all incidental works complete as

directed by the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

49 NS- 12 Providing and fixing decorative metal inlay/insert of approved Solid Brass, of approved finish (mirror, Rmt 1,202.15 100.00 1,20,215.00

brushed, matt, antique, PVD, hairline or as approved), width, thickness and profile as per approved

drawings, accurately cut, shaped and fixed flush with adjacent finished surfaces using approved

adhesive, mechanical fasteners and accessories wherever required, including cutting grooves,

alignment, polishing, cleaning, protection and all incidental works complete as directed by the

Engineer-in-Charge

50 NS- 13 Supplying and laying approved carpet tiles, 500 mm × 500 mm, made of solution-dyed nylon with pile Sq.m 4,267.90 50.00 2,13,395.00

height of 4–5 mm and minimum total weight of 4000 GSM, having StableShield backing or approved

equivalent. The rate shall include supply of all materials, labour, approved adhesives, fixing

accessories, cutting, fitting, trimming, wastage, transportation, handling, surface preparation, cleaning,

and all incidental works required for complete installation and proper finishing, in accordance with the

approved drawings, manufacturer's specifications, and the directions of the Engineer/Architect,

complete in all respects (Basic rate - 220 Rs/Sq.ft)

51 NS- 14 Providing, supplying and laying Area Rug of approved make, design, colour, pattern and texture, Sq.m 28,452.75 50.00 14,22,637.50

suitable for heavy commercial office use, machine tufted/hand tufted as specified, with minimum pile

height of 8–12 mm, anti-skid backing, stain-resistant and fade-resistant properties, complete with edge

binding, cutting to required shape and size, placing in position, including transportation, handling, all

incidental materials and accessories, complete as per approved drawings and as directed by the

Engineer-in-Charge (Basic rate - 1500 Rs/Sq.ft)

52 NS- 15 Providing and laying Premium Engineered Oak Wood Flooring (Classic Range) of approved make, Sq.m 12,092.40 272.00 32,89,132.80

colour, grade and finish, comprising a 13 mm thick dimensionally stable 3-layer engineered

construction with minimum 2.5 mm thick genuine Oak wood wear layer, solid softwood core and

balancing veneer backing, factory manufactured and factory finished with UV-cured matt lacquer,

extra matt lacquer or natural oil finish, complete as specified.

The flooring shall comprise Living Grade Oak (or Natur/Rustic Grade where specified), 13 mm overall

thickness, minimum 2.5 mm Oak wear layer, plank size approximately 2200 × 185 mm, 4-sided micro

bevel (M4V) edges, smooth/brushed/lightly textured surface as approved, and shall be factory

conditioned for dimensional stability. The flooring shall be installed using a precision click-lock system

for floating installation or full-surface bonded installation with approved elastic wood flooring

adhesive, strictly in accordance with the manufacturer's recommendations.

The work shall include preparation and checking of the substrate, approved acoustic underlay or -

elastic adhesive as specified, installation by trained applicators, provision of matching engineered

wood skirting, reducers, T-profiles, end trims, stair nosings, thresholds and all proprietary accessories,

formation of expansion gaps and movement joints, cutting and fitting around columns, door frames

and service penetrations, complete cleaning, protection of finished flooring and making good all

disturbed finishes.

The flooring system shall be suitable for interior applications, compatible with approved underfloor

heating/cooling systems where recommended by the manufacturer, and shall be supplied complete

with all accessories required for a complete installation. The product shall carry a minimum 25-year

residential warranty and 10-year commercial warranty against manufacturing defects, complete in all

respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-in-

Charge (Basic rate- 850 Rs/Sq.ft)

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

53 NS- 16 Providing and laying Premium Laminate Flooring (Classic Range) of approved make, colour, shade, Sq.m 5,406.00 501.00 27,08,406.00

texture and finish, comprising minimum 8 mm thick High Density Fibreboard (HDF) core board with

decorative impregnated paper layer and transparent abrasion-resistant overlay, factory manufactured

and finished complete as specified.

The laminate flooring shall have minimum 8 mm thickness (9 mm where specified), plank size

approximately 2200 mm long or approved equivalent, Class 23 Residential and Class 33 Heavy

Commercial wear classification, minimum AC5 abrasion resistance, minimum 48-hour water resistance,

moisture-resistant HDF core with edge impregnation, 4-sided V-groove (4V) edges, and a micro scratch-

resistant, anti-static and stain-resistant surface finish. The flooring shall be installed using a factory-

engineered angle-click/click-lock floating system (Safe-Lock® Pro or approved equivalent) without

adhesive and shall be compatible with approved acoustic underlay and underfloor heating/cooling

systems where recommended by the manufacturer. The product shall comply with recognised low VOC

indoor air quality standards such as Blue Angel, FloorScore, A+, GREENGUARD Gold or equivalent.

The work shall include supply and installation of approved acoustic/moisture barrier underlay, floating -

installation over a prepared and level substrate, matching skirting boards, reducers, T-profiles, end

trims, stair nosings, thresholds and all proprietary accessories, provision of expansion gaps and

movement joints, cutting and fitting around columns, door frames and service penetrations, cleaning,

protection of completed flooring until handover, and making good all disturbed finishes.

The laminate flooring shall be installed strictly in accordance with the manufacturer's written

recommendations and approved drawings, complete in all respects, and shall carry a minimum

Lifetime Residential Warranty and 10-year Commercial Warranty against manufacturing defects. (Basic

rate - 300 Rs/Sq.ft)

54 NS- 17 Providing and fixing PVC Sports Flooring of 4.50 mm thickness in rolls of 1.80 m × 20.00 m, laid over a Sq.m 3,414.35 44.00 1,50,231.40

clean, smooth and properly prepared subfloor using approved adhesive, including cutting, jointing,

welding of joints wherever required, finishing at edges and all incidental works complete. The flooring

shall be termite and bug resistant, possess superior stain, scratch, fire and chemical resistance, require

zero maintenance, be easy to clean with soap and water, and have a factory-applied PUR

(Polyurethane Reinforcement) wear layer. The product shall be phthalate-free, have zero VOC

emissions, and provide superior dimensional stability and indentation resistance. The flooring shall be

suitable for professional sports facilities, multipurpose halls, gymnasiums, kindergartens and similar

applications requiring athletic performance, safety, energy absorption, noise reduction and durability.

The product shall be manufactured in India, conform to ISO 10582 for PVC flooring, comply with

applicable BIS standards, be FloorScore® certified for Indoor Air Quality (IAQ), and comply with EN 651

Class 23, EN 428, EN ISO 717-2 / EN ISO 140-8 for impact sound insulation, EN 13501-1 for flammability,

EN 13036-4 for rotational friction, DIN 18032, EN 14808 for shock absorption, EN 14809 for vertical

deformation, EN 12235 for ball rebound, EN 2813 for specular gloss, EN 434 for dimensional stability,

EN 1516 for indentation resistance, EN 1569 for resistance to rolling load, ISO 105-B02 for colour

fastness, EN 423 for chemical resistance, EN ISO 5470-1 for abrasion resistance (H18 wheel), EN 660-2

Group T for abrasion classification, and comply with IMO Resolution A.653(16) and IMO MSC.61(67) for

fire resistance. The rate shall include supply of all materials, approved adhesive, labour, cutting,

jointing, welding of seams, finishing, transportation, tools and tackles, and all other incidental works

required for complete installation as directed by the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

55 NS- 18 Providing and fixing rubber flooring of 25 mm thickness in tile size 500 mm × 500 mm, manufactured Sq.m 3,058.65 65.00 1,98,812.25

from high-density vulcanized rubber, in approved colour and finish, laid over a clean, smooth and

properly prepared subfloor using approved polyurethane/rubber flooring adhesive as recommended

by the manufacturer, including cutting, fitting, alignment, finishing at edges, and all incidental works

complete. The flooring shall be slip resistant, impact absorbing, anti-skid, wear resistant, durable, easy

to clean and maintain, and suitable for gymnasiums, fitness centres and other high-impact

applications. The rate shall include supply of rubber tiles, approved adhesive, labour, cutting, fitting,

transportation, tools and tackles, and all other materials and operations required for complete

installation as directed by the Engineer-in-Charge

56 R3-CS-PN- Providing and applying antifungal self leveling 3mm EPU system including coving at floor wall junction, Sq.m 1,562.32 44.00 68,742.08

25 necessary surface preparation by cleaning and de-dusting. The System shall be executed in three

stages, firstly by applying a solvent free epoxy primer which has a volumetric ratio of mixing @ 200

microns dft, then laying 1.8mm self leveling epoxy based screed and finally applying a solvent free EPU

( epoxypolyurethane), self leveling coating to yield a dft of 1000 microns. The EPU coating shall be a

two component with volumetric ratio of mixing. No fillers shall be added at the site while laying the

self leveling EPU including Aisle or zone marking in different colours etc. complete as per

manufacturers specifications and as directed & approved by Engineer In-Charge.

57 NS- 19 Providing and fixing powder-coated aluminium skirting of 75 mm height, manufactured from extruded Rmt 782.45 50.00 39,122.50

aluminium sections of approved alloy and temper, with factory-applied powder-coated finish in

approved colour, fixed to walls using approved screws, clips, brackets, or adhesive as recommended by

the manufacturer, including cutting, mitre joints, internal and external corners, end caps, joining

accessories, alignment, sealing where required, and all incidental works complete. The rate shall

include supply of all materials, fittings, fasteners, labour, transportation, tools and tackles, and all

operations necessary for complete installation as directed by the Engineer-in-Charge

58 11.53 Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in Sq.m 3,891.15 100.00 3,89,115.00

all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic

tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per

sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern

approved by Engineer-in-Charge:

16.91 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, -

lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by

table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted

bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand

bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and

cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete

all as per direction of Engineer-in-Charge.

59 16.91.2 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. Sq.m 1,091.50 469.00 5,11,913.50

11.54 Providing and fixing removable raised/false access flooring with system and its components of -

approved make for different plenum height with possible height adjustment upto 50 mm, comprising

of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I.

Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-

in-charge consisting of:

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of -

thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size

100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size

75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check

nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in

position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate

using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size -

570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head

using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the

pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid,

rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance

between the bottom of the floor for electrical conduits and wiring etc. all complete as per the

architectural drawings, as specified and as directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static -

high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded

construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top

and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together

(minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist

epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with

Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound. The

access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology

upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to

withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the

centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly

Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge. All specification

must be printed on the side of the panel to ensure the quality of the product.

60 11.54.1 300 mm Finished Floor Height (FFH) Sq.m 5,623.95 3.00 16,871.85

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of -

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick

with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with

dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle

hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle

hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre

to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26

mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular

to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at

every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm

and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling

section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c,

including jointing and finishing to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers

covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer's specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting with :

61 12.45.1 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS Sq.m 1,355.80 2,265.00 30,70,887.00

certification marks)

62 NS- 20 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 569.05 2,000.00 11,38,100.00

up to 25 mm, including preparation of templates, casting/manufacturing of mouldings, cutting, fitting,

fixing with approved adhesive and POP, filling joints, sanding, finishing, and preparing the surface

ready to receive paint, complete in all respects as per approved drawings, specifications, and

directions of the Engineer-in-Charge.

63 NS- 21 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 711.30 1,000.00 7,11,300.00

above 25 mm and up to 50 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge.

64 NS- 22 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 853.60 1,000.00 8,53,600.00

above 50 mm and up to 100 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge.

65 NS- 23 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 995.85 1,000.00 9,95,850.00

above 100 mm and up to 200 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

66 NS- 24 Providing and fixing decorative gypsum/POP moulding/cornice of approved profile, having projection Rmt 1,280.35 500.00 6,40,175.00

above 200 mm and up to 300 mm, including preparation of templates, casting/manufacturing of

mouldings, cutting, fitting, fixing with approved adhesive and POP, filling joints, sanding, finishing, and

preparing the surface ready to receive paint, complete in all respects as per approved drawings,

specifications, and directions of the Engineer-in-Charge

67 R3-CS-WW- Providing&fixing TRAP DOOR with T.W. frame work and shutter made from19mm marine plywood and Sq.m 7,865.88 7.00 55,061.16

43 exposed surface finished with 1.5mm laminateand internal surface finished with flat oil paint with s.s.

fittings & fixtures as per Architects detailed drg. and design.

12.52 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, -

suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120

grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get

required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm

center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm

long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and

secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to

be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size

24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required

cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc.

Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed

to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised

butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom

exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all

heights as per specifications, drawings and as directed by Engineer-in-charge.

68 12.52.1 GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm Sq.m 1,902.95 50.00 95,147.50

thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and

electro statically polyester powder coated of thickness 60 microns (minimum), including factory

painted after bending.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

12.59 Providing & fixing false ceiling at all height including providing & fixing of framework made of special -

section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side

inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of

27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x

50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling

section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of

10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with

connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing

perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter

of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry

wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and

perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing

& finishing to a flush finish of tapered and square edges of the board with recommended jointing

compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on

both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification

and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with

frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of

the Engineer in charge but excluding the cost of painting with:

69 12.59.1 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with Sq.m 1,572.30 160.00 2,51,568.00

cellulose fiber manufactured through autoclaving process.

26.26 Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling -

tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than

2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476

(part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on

inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120

grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000

mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32

mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using

galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-

6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster

of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to

be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and

40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as

per directions of the Engineer-in-Charge.

70 26.26.1 With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles. Sq.m 1,852.05 650.00 12,03,832.50

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

26.27 Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved

texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance ≥

85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true

horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of

0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm,

cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of

length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild

steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter

fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced

at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with

the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to

the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws.

The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted

with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings

and as per directions of the engineer-in-charge.

71 26.27.2 With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) Sq.m 2,671.20 20.00 53,424.00

72 PWD SSR ACOUSTICAL WOODWOOL FALSE CEILING: Providing & fixing of 100% Natural Material- Magnesite Sq.m 9,464.19 5.00 47,320.97

2022-23 (Hygroscopic & biologically sound binding agent) bonded woodwool Heradesign planks of

53.33 600Mm*1200Mm *25Mm thickness made out of wood wool fiber of width 1Mm Fiber thickness mixed

with Natural water & Magnesite (No-Cement) with open & smooth surface texture, Weight of panel to

be 11.3 Kg/m2. A Completely harmless Environment & Human Friendly & also a disposable or

recyclable Material & can last for more than 80 Years in building interiors As it has long lifespan &

suitable for Indoor conditions with relative air humidity of upto 90%. Magnesite protects the wood

cells against ageing & fungal attack. To achieve upto NRC=1.00 it should be a clear gap of 200Mm from

wall slab along with the backing of Mineral wool of 50mm thick with 64 kg/m3 density. Ecologically

Sound Material with high mechanical strength with Crash test of 90Km/H with Ball Impact Test

DIN18032 & EN13964 with flying colors & A sustainable material (PEFC & FSC Certified) along with EPD

Certified Acc. to EN ISO 14025 (AUB-Environmental Product declaration). Manufacturing tolerance for

nominal size: Length, Width & Thickness ± 1 mm, & In a Standard Climate of 23° C and 50% rel.

FIXING & SUBSTRUCTURE: Impact Resistant According to DIN-18023 or EN13964 to be Fixed on CD -

Sections Profile framework with Screw 9Pc/Panel & Centre Distance Support of 300Mm & Centre

distance of Cross Profile would be at 600Mm & Main Profile at 900Mm CD Profile is made out of GI(

Sections Profile 60/27/0.6Mm-0.6MmThick x 60Mm Width x 0.27Mm height). The Main Profile is in the

length of 3000mm & to form a section of 600mm x 1200mm. The CD Profile is to be suspended from

soffit with the help of nonius hanger at a center distance of 900mm. UD Profile 28/27/0.6mm to be

fixed on wall at the perimeter of the wall. If the main CD profile needs to extended, it needs to be

connected with CD profile connector 60/27. The CD profiles to be connected to each other at the

intersection by CD cross connector. Heradesign Superfine panels to be fixed to the ceiling with a

minimum of 200mm void or gap with Galvanized screws of length 50Mm & Dia 4.5Mm with a backing

of Mineral Wool of density 64kg/m3 density (50mm thick). Colour pf Panels : NATURAL BEIGE, Can be

Painted to the desired colour (Any- RAL, NCS or StoColor Shades) using water based color by Spray

method prior to installation. FIRE CLASS as per EN 13501-1:B –s1, d0. Test Certificates to be submitted.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

73 NS- 25 Providing and fixing horizontal level suspended ceiling comprising of Vertical Linear Baffle Ceiling Sq.m 10,100.70 44.00 4,44,430.80

made out of extruded aluminium in aluminium alloy grade 6063-T5, with baffle blades of size 100/150 x

25 x 3600 mm (nominal), powder coated to approved Woodgrain/Plain finish such as Red Oak, Cherry,

Black/White, with electrostatically applied polyester powder coating of 60–80 micron thickness. The

powder coating shall comply with the specified performance requirements including Salt Spray Test for

750 hours as per ASTM B117, QUV-A Test for 1000 hours as per ASTM G-154 Cycle-1, Humidity Test for

1000 hours as per DIN 50017, adhesion GT0 as per EN ISO 2409, shade variation within manufacturing

batch of Delta E<1 and gloss level of 25±5% at 60° as per ASTM D523, where applicable. The baffle

blades shall be suspended using slotted U-profile of 20 x 30 x 3700 mm, 1.5 mm thick, having slots at 25

mm module to maintain the required on-centre spacing of baffles, with longer lengths connected using

baffle joiners and ends finished with end caps. The suspension system shall comprise powder-coated

mild steel U-profiles of 20(W) x 30(H) x 3750(L) mm, rolled from 1.5 mm thick MS sheet and having

alternate square and rectangular slots of 6.5 x 6.5 mm and 28 x 6.5 mm respectively for fixing baffle

hangers using plugin clips, including U-profile splices, baffle hangers, plugin clips, U-profile hangers and

threaded rods for suspension from the true ceiling. The complete system shall include all necessary

proprietary suspension components, fixing accessories, levelling, alignment, cutting, jointing, end

finishing, labour, tools, tackles and incidental materials, complete in all respects as per approved

manufacturer's specifications, drawings and directions of the Engineer-in-Charge/Architec

74 NS- 26 Stretch fabric ceiling : Providing & Fixing Classic white translucent back light non flammable stretch Sq.m 17,071.65 10.00 1,70,716.50

ceiling with thickness of 0.15 to 0.20 mm. Custom made stretch false ceiling to fit exact dimensions

with aluminum supports.Translucent stretch ceiling composed of calendared PVC [Polyvinyl Chloride

based guaranteed cadium free] membrane with harpoon & corners ready to install. Membrane to

transmit 77% of incident backlight light & absorb 23%. CE certified. Weight of membrane to be 230 gms

/ m2 approx. Panel to be with 10 years warranty on membrane, seam ruptures, discoloration, sag &

profile.Heavy metal and toxic components free.Fire rating: EUROCLASS = B-s1,d0. Humidity resistance.

100% recyclable with USGBC Member Certificate ISO 9001:2015 Certified. To be completed with

wooden / metal base work and LED Lighting.

75 NS- 27 Providing and fixing Veneer False Ceiling consisting of 4mm thick natural wood veneer pressed on Sq.m 10,243.00 779.00 79,79,297.00

12mm thick BWP grade plywood, factory bonded with approved adhesive. The plywood panels shall be

fixed to a concealed framework made of galvanized iron (GI) channels and perimeter sections,

suspended from the RCC slab/structural members using GI suspension rods, cleats, dash fasteners and

necessary hardware. The framework shall ensure a rigid, levelled and true ceiling surface.The veneer

surface shall be finished in site with sanding, wood filler and three coats of polyurethane (PU) clear

finish with inter-coat rubbing to achieve a uniform smooth finish. All cut edges shall be sealed. Panels

shall be installed with proper grain direction, alignment and tight joints as per approved drawings

(Veneer basic rate - 300 Rs/Sq.ft)

76 NS- 28 Providing and fixing decorative seasoned 2nd class Indian Teak Wood mouldings, beadings, cornices, Cu.m 2,84,527.30 10.00 28,45,273.00

edge trims and veneer matching mouldings of approved design, profile and size, machine cut and

accurately shaped, fixed with concealed screws, approved adhesive and necessary hardwood

cleats/supports wherever required, including all cutting, shaping, rebating, grooving, mitred joints,

sanding, filling, making good adjoining surfaces, complete with three or more coats of approved

melamine polish over one coat of wood filler/sealer to achieve a uniform finish, including all materials,

labour, scaffolding, tools & tackles, wastage and all incidental works, complete as per approved

drawings and directions of the Engineer-in-Charge.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

77 NS- 29 Fire Resistant Glazed Slimline Fixed Partition (120 Minutes – EW 120) Sq.m 99,584.55 5.00 4,97,922.75

Providing, supplying and installing tested slimline fully glazed fire-rated fixed partition system with 120

minutes Integrity and Radiation Control (EW 120), providing symmetrical (bi-directional) fire

protection, complete with factory-fabricated cold rolled galvanized steel profiles of minimum 1.5 mm

thickness, tested as per EN 1364-1:2015 for non-load bearing partitions by an internationally

accredited laboratory.

The glazing shall comprise 14 mm thick clear, fire-rated, non-wired, toughened interlayered glass

providing 120 minutes Integrity (E) and Radiation Control (EW 120), with U-value of 5.02 W/m²K,

minimum 86% light transmission, 38 dB sound reduction, and complying with Class 1(B)1 Impact

Resistance as per EN 12600. The glass shall be tested for UV stability in accordance with EN 12543-4,

provide bi-directional fire protection, and possess a valid Environmental Product Declaration (EPD) in

accordance with EN 15804 and ISO 14025, including recycled content declaration.

The partition frame shall be fabricated from 1.5 mm thick cold rolled galvanized steel profiles forming

50 mm × 80 mm sections with 15 mm flange, with 38 mm face width mullion sections. The frame shall

be fixed to the supporting structure using M10 or larger anchor fasteners at 150 mm from edges and

approximately 500 mm c/c thereafter, or as per approved test evidence.

The glazing shall be secured with minimum 1.25 mm thick steel glazing beads, approved fire-rated -

glazing tape/gasket, and 3 mm thick non-combustible calcium silicate setting blocks, complete with

stainless steel self-tapping studs, sealants, fasteners and all necessary accessories.

The complete partition system shall be tested and certified for fire resistance in accordance with EN

1364-1:2015 by an internationally accredited laboratory. Test reports and certificates shall be duly

signed by the authorized laboratory representative and supported by a certificate of compliance issued

by an authorized certification body. Installation shall be carried out by a manufacturer-approved

certified installer, and the installed system shall be inspected for compliance by the manufacturer or its

authorized representative. The item shall include all materials, fabrication, transportation, installation,

alignment, sealing, testing, certification, finishing and making good complete as per approved

drawings, manufacturer's specifications and the directions of the Engineer-in-Charge.

78 NS- 30 GD3 & GD4-Providing and fixing fully glazed aluminium framed door comprising 50 × 50 × 2 mm thick Sq.m 15,649.00 25.92 4,05,622.08

aluminium box section frame of approved make and finish, fabricated, welded/mechanically joined,

reinforced wherever required, and securely fixed in position with approved fasteners, anchor bolts,

cleats and accessories. The door shutter shall consist of 12 mm thick clear toughened safety glass

conforming to ASTM C-1048, fixed within the aluminium frame using approved EPDM gaskets, glazing

beads, setting blocks and weather-resistant silicone sealant, complete with machine-polished edges

The item shall include supply and fixing of SS 304 grade heavy-duty patch fittings/connecting brackets

wherever required, floor spring of approved make, pivot set, hydraulic door closer (where specified),

mortise lock/patch lock with euro cylinder, SS 304 satin-finish D-type pull handles of suitable length on

both sides, hinges/pivots, door stoppers, all necessary operating hardware, stainless steel screws,

chemical anchors, sealants, packers and all accessories required for smooth and complete operation.

The work shall include all cutting, fabrication, assembly, installation, alignment, adjustments, testing,

making all joints watertight, cleaning of glass and aluminium surfaces, protection until handing over,

and completion in all respects as per approved drawings and directions of the Engineer-in-

Charge/Architect.

Metal Fire rated doors -120minutes -

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

Providing and fixing ISI marked fire rated GI Sheet doors conforming to FD 120-UD classification of IS -

3614 :2021 with fire rating of 120 minutes integrity only. The factory manufactured door frame and

shutter assembly shall be made out of minimum 1.50 mm thick GI Sheet with minimum 120 g/m2

coating as per IS: 277.

The Door should be finished with powder coating in standard RAL shade finish having DFT of minimum

50 microns. The door should carry a minimum 500 Hrs of salt spray test. All accressesories like

hardware, vision panel, fire & smoke seal etc to be supplied by Fire door manufacturer only as per the

guidelines laid down in IS 3614:2021.

Every door must be ISI labeled confirming to type of door & its fire rating.

The offered door must carry a prior valid test evidence of 5 years from CBRI-Roorkee. No fresh testing

is required within the validity of test report from CBRI Roorkee.

The Door frame shall be single rebate grooved profile to accomodate 10x4mm Fire Seal, Size of Frame -

to be minimum 125mm x 55mm made out of minimum 1.50mm thick galvanized steel sheet. Frames

shall be butt / mitered joint and field assembeled with bolting system. The frame should also be

provided with fire rated smoke seal as per IS: 3614:2021 or as per test evidence. It shall be pasted on

surface and perimeter of main frame. All provisions should be mortised & provided with necessary

inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate

bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide

sleeves for installation of frame in finished plastered masonary wall opening.

Door leaf should be minimum 60mm thick fully flush double skin door. Door leaf must be -

manufactured from 1.2mm(18gauge) thick galvanised steel sheet. The infill material shall be

honeycomb craft paper insulation. All doors shall be factory prepped for receiving appropriate

hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges

should be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has

to be provided on the meeting stile for both active and inactive leaf.The shutters shall be mounted to

the frame with SS 304 grade ball bearing type hinges of size 100x89x3 mm alongwith all suitable

Vision lite glass size 300mm x 400mm (max area upto 0.12sqm) wherever applicable should be -

provided with single layered clear fire rated glass panes as per guidelines laid down under IS 3614 :

2021 vide clause no. 7.2.7 table no. 2 with a clipon arrangement. The glass will be provided with fire

rated ceramic tape of suitable size alround on either face. Every Glass pane must carry a permanent

marking. Door must be tested with vision panel- 6mm thick pyroswiss glass.

(Rate including Frame +Shutter +installation+transportation) -

Hardware Description -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws -

Supply & fixing of anchor fastners M10X120mm length. -

Mortice Sash Lock -complete Set with 70mm BSK Operation & Lever Handle -

Tower bolt 200 mm -

21.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with

EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of

engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

80 21.3.2 With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) Sq.m 1,505.25 0.27 406.42

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

9.24 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded)

(overall area of door shutter to be measured):

81 9.24.1 Rectangular or square Sq.m 199.15 4.80 955.92

Wooden fire rated door -120 min- -

Providing and fixing Fully Insulated Non Metallic Wooden doors as per IS 3614:2021, for 120 min -

integrity & 120 min insulation. The door is made out of thoroughly seasoned hard wood. The moisture

content of any material used in the construction of wooden composite fire door sets comprises of both

frame and shutter shall not be more than 15% approx. in accordance with IS 287. The fire door must

have earlier test evidence as per IS/ISO 3008-1. It must have successfully tested from CBRI , Roorkee /

IPIRTI / NABL accrediated lab which operates in accordance with ISO/IEC 17025 for for its fire rating.

Door and frame shall be finished with fire retardent primer FR880.All accressesories like hardware, fire

seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS

3614:2021.Every door must carry a label confirming to type of door & its fire rating.

Door frame shall be Single rebate profile of section 120 x 60 mm made out of Hard wood having -

density should not less than of 550-600 kg/m3 approx. with factory made groove of suitable size so as

to accomodate intumuscent Fire seal of size 20x4mm . An EPDM seal also to be provided in the frame

to check spread of smoke. The frame must be primed with Fire retardant primer FR880 . The frame to

be fixed to fire exit opening with minimum 10 nos. 10 mm dia and minimum 120 mm long HDG (hot dip

galavanized) headed screws with polyamide sleeves.

Wooden shutter with liping should not less than 52mm of thickness finished with commercial ply on -

both faces. If required, the Commercial ply may be replaced with teak ply or may be pasted with 1.5

mm thick Laminate on both faces in desired regular SF grade (any upgradated finish will be payable

extra). The composite thickness of the core insulation will be 37mm consists of minimum 10mm thick

Calcium Silicate boards of Hilux / Pamtech make and treated wool Insulation material . The calcium

silicate board must have Density not more than 900kg/m3 , having thermal conductivity 0.15W/mK .

The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm

mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed

wooden lipping .The shutters shall be mounted to the frame with SS 304 grade ball bearing type hinges

alongwith all suitable hardware

(Rate including Frame +Shutter +installation+transportation) -

Hardware Description -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws -

Supply & fixing of anchor fastners of M10X120mm length. -

Supply and Fixing of intumescent fire seal of size 10x4mm -

Supply and Fixing of EPDM Smoke seal -

Supply & fixing of DOOR CLOSER WITH SLIDING ARM -

Supply & fixing of Mortise Dead Lock with 70mm long Euro Profile Cylinder with one Side key other side -

thumb operation

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long. -

Wooden door NFRD -

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

Providing & fixing of wooden flush door perfectly seasoned & chemically treated wood. All Flush doors -

are solid core construction bonded with pine wood, confirming to IS-2202 Part-1:99. Duly Factory

pressed and structurally & dimensionally stable. All our doors are pine wood core confirm all IS

Door leaf shall be 35 mm thick (23+10+2=35mm) flush door lipping, comprising of 23mm internal core -

100% pine wood cladded with 5mm thick play on both side & 1.5 mm thick Laminate sheet pasted on

both face of the Shutter (As per approved make & shade). Shutter Edges are finish matching to the

door finishing and as per approved sample.

(Rate including Frame +Shutter +installation+transportation) -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete -

Supply & fixing of Mortise Dead Lock 70mm long Euro Profile Cylinder withlever handle both the side -

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long -

Louver grill-450x150mm -

Supply & fixing of SS 304 grade Ball Bearing Hinges of size 100 x 75 x 3mm complete -

Supply & fixing of Mortise Dead Lock 70mm long Euro Profile Cylinder withlever handle both the side -

Supply & fixing of SS 304 grade D Type SS Pull Handle B2B of size 300mm mm Long -

Louver grill-450x150mm -

SS panic bar- -

Metal Fire rated doors -120 minutes Insulation 30 min - -

Providing and fixing ISI marked partially insulated fire rated GI Sheet doors conforming to FD 120-PI -

classification of IS 3614 :2021 with fire rating of 120 minutes integrity and 30 minutes insulation. The

factory manufactured door frame and shutter assembly shall be made out of minimum 1.50 mm thick

GI Sheet with minimum 120 g/m2 coating as per IS: 277.

The Door should be finished with powder coating in standard RAL shade finish having DFT of minimum

50 microns. The door should carry a minimum 500 Hrs of salt spray test. All accressesories like

hardware, vision panel, fire & smoke seal etc to be supplied by Fire door manufacturer only as per the

guidelines laid down in IS 3614:2021.

Every door must be ISI labeled confirming to type of door & its fire rating.The offered door must carry a

prior valid test evidence of 5 years from CBRI-Roorkee. Required third party test report from CBRI

The Door frame shall be single rebate grooved profile to accomodate 10x4mm Fire Seal, Size of Frame -

to be minimum 125mm x 75mm made out of minimum 1.50mm thick galvanized steel sheet. Frames

shall be butt / mitered joint and field assembeled with bolting system. The frame should also be

provided with fire rated smoke seal as per IS: 3614:2021 or as per test evidence. It shall be pasted on

surface and perimeter of main frame. All provisions should be mortised & provided with necessary

inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate

bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide

sleeves for installation of frame in finished plastered masonary wall opening.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

Door leaf should be minimum 60mm thick fully flush double skin door. Door leaf must be -

manufactured from 1.2mm(18gauge) thick galvanised steel sheet. The infill material shall be mineral

wool of minimum density 96 kg/cum. All doors shall be factory prepped for receiving appropriate

hardware and provided with necessary reinforcement for hinges, locks, and door closers. The edges

should be interlocked with a bending radius of 1.4mm. For double leaf doors integrated astragals has

to be provided on the meeting stile for both active and inactive leaf. The shutters shall be mounted to

the frame with SS 304 grade ball bearing type hinges of size 100x89x3 mm alongwith all suitable

All doors and frames shall be finished with Powder coating in desired RAL Shades. as per the directions -

of the Engineer & site team.

Rate shall include supply and installation of frame, shutter as a complete assembly, including all -

hardware & glass with tapes.

Application : Staircase -

(Rate including Frame +Shutter +installation+transportation)

86 PWD SSR Providing and fixing of factory made uPVC Louver window (White Colour) comprising of uPVC multi- Sq.m 11,438.45 10.00 1,14,384.48

2022-23 chambered with wall thickness of 2.3mm (+-0.2 mm ), duly reinforced with 1.5 mm thick G. I. Section.

54.11 uPVC window & door profile shall be made in India & shall conform to BS EN 12608 and other

standards as mentioned below: S.No. Name of the test Test Method Specifie Parameter

1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat Softening

Temperature EN ISO – 306 Shall not be < 750C

3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2

4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2

5 Mean Breaking Stress for welded corner

(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2

(b) For the compression bending test Shall not be < 30N/mm2

6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %

7 Surface Spread of flame BS : 476 - Part 7 Classification 1

8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable

9 Tensile modulus ASTM D 638 Shall not be < 35 MPa

10 Shear Modulus ASTM D 732 Shall not be < 220 MPa

11 Tensile Strength EN ISO 527 Shall not be < 30 MPa. All corners of frame shall be fusion welded. Both

vertical sides of the frame, adjustable louver mechanism having one lever or fixed louver bracket shall

be fitted with the of 4 mm Frosted Annealed glass. Window will be fixed to the wall with 100mm long

and 8mm dia. Fasteners and complete in all respect as per direction of Engineer-In-Charge.

uPVC Window and Door Profiles are warranted for a period of ten (10) years against non-uniform

discoloration,wrapping and rotting under general use.

a.Louver Window (Big Series) frame of size 67 x 62 mm & Mullion (if required) of size 67 x 78 mm.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

PWD SSR Providing and fixing of factory made uPVC casement window / Fixed Window & Casement Door (White

2022-23 Colour) comprising uPVC multi-chambered frame, Sash, & Mullion with wall thickness of 2.3mm (+-0.2

54.09 mm ), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC window & door profile shall

be made in India & shall conform to BS EN 12608 and other standards as mentioned below: S.No. Name

test Test Method Specified Parameter

1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat

Softening Temperature EN ISO – 306 Shall not be < 750C

3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2

4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2

5 Mean Breaking Stress for welded corner

(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2

(b) For the compression bending test Shall not be < 30N/mm2

6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %

7 Surface Spread of flame BS : 476 - Part 7 Classification 1

8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable

9 Tensile modulus ASTM D 638 Shall not be < 35 MPa

10 Shear Modulus ASTM D 732 Shall not be < 220 MPa

11 Tensile Strength EN ISO 527 Shall not be < 30 MPa. All corners of frame and sash

will be fusion welded. Mullion shall be welded / screwed. EPDM / TPE Gasket shall be

provided in all frame, sash & mullion, wherever necessary.Thereafter, 5 mm Float

Annealed glass shall be provided in the sash with the help of uPVC glazing bead and

hardware, i.e., friction hinge & single point handle (in window) & 3D Hinges &

Multipoint Lock (in door) shall be provided. Window / Door shall be fixed to the wall with

100mm long and 8mm dia. Fasteners and complete in all respect as per direction of

Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a period of ten

(10) years against non-uniform discoloration, wrapping and rotting under general use

87 a Casement Window (Big Series) frame of size 67 x 62 mm & Sash / Mullion of size 67 x 78 mm. Sq.m 13,003.31 50.00 6,50,165.25

88 c Fixed Window (Big Series) frame of size 67 x 62 mm & Mullion (if required) of size 67 x 78 mm Sq.m 10,335.74 10.00 1,03,357.38

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

PWD SSR Providing and fixing of factory made uPVC Sliding window & door (White Colour) complete, comprising

2022-23 uPVC multi-chambered frame having in-built uPVC roller track on top and uPVC sash with wall

54.08 thickness of 2.3mm (+-0.2 mm), duly reinforced with G.I. section 1.5 mm, wherever required. uPVC

window & door profile shall be made in India & shall conform to BS EN 12608 and other standards as

mentioned below: S.No.

Name of the test Test Method Specified Parameter

1 Tensile Impact Strength ISO 8256 - more than 700Kj/m2 2 Vicat

Softening Temperature EN ISO – 306 Shall not be < 750C

3 Charpy Impact Strength EN ISO – 179-2 Shall not be < 20KJ/m2

4 Flexural Modulus Elasticity EN ISO – 178 Shall not be < 2200 N/mm2

5 Mean Breaking Stress for welded corner

(a) For the tensile bending test EN – 514 Shall not be < 25 N/mm2

(b) For the compression bending test Shall not be < 30N/mm2

6 Heat Reversion Test IS:4985-2000 Shall not be > 2.0 %

7 Surface Spread of flame BS : 476 - Part 7 Classification 1

8 Ignitability Evaluation BS : 476 - Part 5 'P' Not easily ignitable

9 Tensile modulus ASTM D 638 Shall not be < 35 MPa

10 Shear Modulus ASTM D 732 Shall not be < 220 MPa

11 Tensile Strength EN ISO 527 Shall not be < 30 MPa

All corners of frame and sash will be fusion welded. After placing 5 mm Float Annealed glass in the

sash, uPVC glazing bead, interlock, EPDM / TPE gasket, brush shall be provided including touch lock and

rollers & proper drainage system shall be provided.

Window / Door will be fixed to the wall with 100mm long and 8mm dia. Fasteners and complete in all

respect as per direction of Engineer-In-Charge. uPVC Window and Door Profiles are warranted for a

period of ten (10) years against non-uniform discoloration, wrapping and rotting under general use

89 c 3 Track with Mesh-2 Glass Sash + 1 Mesh Sash (Each sash shall be half of width of window) (Big Series) Sq.m 12,092.64 25.00 3,02,316.00

Window frame of size 122 x 54 mm & Sash of size 64 x 47 mm.

90 PWD SSR Supply and installation of cubicles of width and depth as per specifications/ site drawings. Cubicle Sq.m 10,313.44 17.00 1,75,328.41

2022-23 height will be 1980 mmTitan Std Series Cubicles: Std Sizes (W x D x H): 900 mm x 1550 mm x 1980

51.166 mm/2039 mm ( Height is including 150 mm gap from bottom) Door Size- 600 mm when top rail of

rectangular cross section is used and 2039 mm when top rail of circular cross section is usedITEM

DESCRIPTION Made from solid grade Merino make compact high pressure laminate as per IS:2046 and

EN-438 manufactured under high specific pressure > 5 MPa and temperature >120°C, All doors will be

of single colour and made of 12 mm thick Merino HPL compact panel. All pilasters will be made of 12

mm thick HPL compact panel. Size of panels to be as per drawing. HARDWARE & ACCESSORIES are Top

rail is made of stainless steel grade 304. There are two options for the top rail. First one comes with a

rectangular cross section (Size to be 55mmx42mmx1.6 mmT) and the other one comes with circular

cross section (Diameter 32 mm). Surface finish to be brush type. A thin plastic film pasted for surface

protection. Corner joinery section made from Stainless steel grade 304. Surface finish to be brush type.

A thin plastic film pasted for surface protection. Size to be 35mmx15mmx0.8 mm. etc complete.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

91 PWD SSR ACOUSTICAL WOODWOOL WALL PANELLING: Providing & fixing of 100% Natural Material- Magnesite Sq.m 8,158.82 5.00 40,794.08

2022-23 (Hygroscopic & biologically sound binding agent) bonded woodwool Heradesign planks of

53.32 600Mm*1200Mm *25Mm thickness made out of wood wool fibre of width 1Mm Fiber thickness mixed

with Natural water & Magnesite (No-Cement) with open & smooth surface texture, Weight of panel to

be 11.3 Kg/m2. A Completly harmless Envirenment & Human Friendly & also a disposable or recyclable

Material & can last for more than 80 Years in building interiors As it has long lifespan & suitable for

Indoor conditions with relative air humidity of upto 90%. Magnesite protects the wood cells against

ageing & fungal attack. To achive upto NRC=1.00 it should be a clear gap of 200Mm from wall slab

along with the backing of Mineral wool of 50mm thick with 64 kg/m3 density. Ecologically Sound

Material with high mechanical strength with Crash test of 90Km/H with Ball Impact Test DIN18032 &

EN13964 with flying colors & A sustainable material (PEFC & FSC Certified) along with EPD Certified Acc.

to EN ISO 14025 (AUB-Envirenmental Product declaration). Manufacturing tolerance for nominal size:

Length, Width & Thickness ± 1 mm, & In a Standard Climate of 23° C and 50% rel. humidity.

FIXING & SUBSTRUCTURE: Impact Resitant According to DIN-18023 or EN13964 to be Fixed on CD -

Sections Profile framework with Screw 9Pc/Panel & Centre Distance Support of 300Mm & Centre

distance of Cross Profile would be at 600Mm & Main Profile at 900Mm CD Profile is made out of GI(

Sections Profile 60/27/0.6Mm-0.6MmThick x 60Mm Width x 0.27Mm height). The Main Profile is in the

legth of 3000Mm & to form a section of 600mm x 1200mm. Heradesign Superfine panels to be fixed on

the wall with a minimum of 200Mm void or gap with Galvanized screws of length 50Mm & Dia 4.5Mm

with a backing of Mineral Wool of density 64kg/m3 density (50mm thick).Colour Of Panels : NATURAL

BEIGE, Can be Painted to the desired colour (Any- RAL, NCS or StoColor Shades) using water based

color by Spray method prior to installation. FIRE CLASS as per EN 13501-1:B –s1, d0. Test Certificates to

92 NS- 35 Providing and fixing laiminated wall panelling on internal walls, beams and other vertical surfaces Sq.m 7,824.50 79.00 6,18,135.50

using an aluminium framework system comprising 50 mm × 25 mm × 1.5 mm thick hollow aluminium

sections arranged at 600 mm × 600 mm grid spacing, securely fixed to the existing wall/structure with

approved anchors, fasteners and accessories, and aligned true to line, level and plumb.

The aluminium sub-frame shall be provided with 12 mm thick BWP grade plywood (IS:710 grade)

backing, securely fixed using approved screws and fasteners. Over the plywood backing, providing and

fixing 1.5 mm thick laminate of approved make, shade and grain pattern, including application of

suitable adhesive, pressing, edge treatment, joint alignment and seamless finishing to achieve a

premium decorative appearance.

93 NS- 36 Providing, supplying and fixing decorative uPVC Fluted Wall Panels of approved profile and design, Sq.m 7,113.20 161.00 11,45,225.20

manufactured from premium grade rigid uPVC, factory finished in approved wood grain, solid colour or

metallic finish, of size 140 mm (W) × 3060 mm (L) with tongue and groove interlocking edges. The

panels shall be fire-retardant, moisture resistant, termite proof, fungus resistant, UV resistant, impact

resistant and dimensionally stable, having minimum tensile strength of 37 MPa, minimum tensile

modulus of 2000 MPa, and no surface distortion at 120°F (approximately 50°C). The panels shall be

fixed over approved aluminium frame work of 600x600 mm grid backing including labour,

transportation and all incidental works, complete in all respects as per approved drawings and

directions of the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

94 NS- 37 Providing & fixing Frost Series Roller Blinds (Custom Printed Series) or as approved. The blinds consist Sq.m 3,556.60 500.00 17,78,300.00

a top tube extruded from non-rusting aluminium alloy with a 2.0 mm wall thickness, and available in 40

mm diameter for small and large blinds respectively. The Frost Series fabric have a thickness of 0.48

mm in approved shades and a composition of 100% PES Polyester Acrylic. The fabric weight shall be

200 GSM (±5%) with a light fastness grade of 4, ensuring long-lasting color durability with best quality.

The fabric is securely enclosed in a suitably designed pocket along with the top tube to ensure smooth

rolling operation. The bottom channel is made of non-rusting aluminium, powder-coated, and of 2.0

mm thickness. Both ends of the bottom channel shall be sealed with end caps in matching color to

provide a neat, elegant, and uniform appearance. The mounting brackets is made of powder-coated

steel, offering superior finish and corrosion protection. The bracket design allow's both overhead and

side mounting and is incorporate a clutch assembly at either end of the blind, capable of handling up to

15 kg of load. ( Fabric basic rate : 180 Rs/Sq.ft)

95 NS- 38 Providing, supplying and fixing Z-type (Zebra / Day–Night) roller blinds, made of dual-layer polyester Sq.m 3,000.00 100.00 3,00,000.00

fabric with alternating sheer (transparent) and opaque bands to allow light control and privacy,

suitable for windows, complete with aluminium roller tube, bottom bar, side brackets, clutch

mechanism, chain/cord control, all fixing accessories, alignment and smooth operation, complete as

per manufacturer’s specifications and directions of the Engineer

96 R3-CS-RM- Providing &Fixing frosted film manufactured by 3 M approved equivalent on glass partition wherever Sq.m 1,532.82 74.00 1,13,428.68

137 required as per the instruction of Architect.

97 R3-CS-FUR- Providing and fixing wall paper / Graphic for highlighting the walls with proper adhesive in line level Sq.m 2,784.80 25.00 69,620.00

28 for reception, conference & Auditorium rooms and wherever required as per the drawings. Basic rate

of Wall paper is Rs..100/- per Sft.

98 NS- 39 Providing and fixing veneer wall panelling on internal walls, beams and other vertical surfaces using an Sq.m 9,958.45 465.00 46,30,679.25

aluminium framework system comprising 50 mm × 25 mm × 1.5 mm thick hollow aluminium sections

arranged at 600 mm × 600 mm grid spacing, securely fixed to the existing wall/structure with approved

anchors, fasteners and accessories, and aligned true to line, level and plumb.

The aluminium sub-frame shall be provided with 12 mm thick BWP marine plywood (IS:710 grade)

backing, securely fixed using approved screws and fasteners. Over the plywood backing, providing and

fixing 4 mm thick natural veneer finish of approved make, shade and grain pattern, including

application of suitable adhesive, pressing, edge treatment, veneer matching, joint alignment and

seamless finishing to achieve a premium decorative appearance. The veneer surface shall be finished

with approved clear PU coating as per manufacturer's recommendations, including surface

preparation, sanding and required number of coats to achieve a smooth, durable and uniform finish..

(Veneer basic rate -300 Rs/Sq.ft)

99 NS- 40 Providing and fixing WPC decorative moulding having projection from 12 mm to 18 mm, Rmt 497.90 3,123.50 15,55,190.65

manufactured from premium quality Wood Plastic Composite, complete with cutting, mitred joints,

approved adhesive, SS screws wherever required, finishing, alignment and making good complete as

per approved drawings and direction of the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

100 NS- 41 Providing and fixing WPC decorative moulding having projection from 18 mm to 25 mm, Rmt 640.20 2,498.80 15,99,731.76

manufactured from premium quality Wood Plastic Composite, complete with cutting, mitred joints,

approved adhesive, SS screws wherever required, finishing, alignment and making good complete as

per approved drawings and direction of the Engineer-in-Charge

101 NS- 42 Providing and fixing WPC decorative moulding having projection from 25 mm to 50 mm, Rmt 924.70 6,871.70 63,54,260.99

manufactured from premium quality Wood Plastic Composite, complete with cutting, mitred joints,

approved adhesive, SS screws wherever required, finishing, alignment and making good complete as

per approved drawings and direction of the Engineer-in-Charge

102 NS- 43 Providing and applying Polyurethane (PU) polish on exposed wooden surfaces, including thorough Sq.m 1,422.65 10.00 14,226.50

surface preparation by cleaning, sanding with suitable grades of sandpaper, filling minor imperfections

with approved wood filler where required, application of compatible wood sealer/primer, and finishing

with two or more coats of clear PU polish (matt, satin or gloss finish as approved) to achieve a smooth,

uniform and durable finish. The PU coating shall provide resistance to abrasion, moisture, stains and

chemicals, complete with intermediate sanding between coats wherever required. The rate shall

include all materials, labour, scaffolding (if required), tools and tackles, and all incidental works

necessary to complete the work as directed by the Engineer-in-Charge

103 NS- 44 Providing and fixing wall-mounted mirror paneling as per approved architectural drawings and design, Sq.m 7,753.40 120.00 9,30,408.00

comprising a perfectly plumb base substrate of 12mm thick BWP Grade Plywood mechanically

fastened to the wall, overlaid with an aluminum sheet to act as a definitive moisture and vapor barrier.

Over this prepared backing, supply and install [5mm] thick Extra-Clear (Low-Iron) Mirror with machine-

polished edges, adhered exclusively using premium non-acidic, neutral-cure mirror silicone and double-

sided spacer tapes to prevent desilvering. The comprehensive rate includes all materials, hardware,

labor, leveling, surface preparation, wastage, and final cleaning, with all material samples, edge

treatments, and grid layouts subject to prior mockup and final approval by the Architect

104 NS- 45 Providing, fabricating and fixing 77 mm overall thick full height or low height partition comprising a Sq.m 12,092.40 981.00 1,18,62,644.40

framework of 50 × 25 × 1.5 mm thick aluminium hollow sections, securely fixed to floor, wall, soffit and

adjoining members with approved cleats, brackets and anchor fasteners. The framework shall be filled

with 50 mm thick acoustic Resimer infill (to be measured and paid separately under the relevant BOQ

item) to improve sound insulation performance. The framework shall be clad on both sides with 12 mm

thick BWP Grade plywood conforming to IS:710 and finished on both exposed faces with 1.0 mm thick

decorative high-pressure laminate of approved make, shade and texture, bonded with approved

adhesive. The partition shall have an overall finished thickness of 77 mm. The item shall include all

intermediate framing members, stiffeners, cleats, brackets, fasteners, screws, adhesives, sealants,

cutting, routing, drilling, edge finishing, matching laminate edge banding, finishing to all exposed

edges, corners, returns, jambs, end closures, aluminium trims/beadings wherever required, making

openings for services, making good, cleaning and all labour, materials, tools and tackles complete in all

respects as per approved drawings and directions of the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

105 NS- 46 Providing and fixing 50 mm thick Acoustic Resimer FR infill within aluminium partition framework, Sq.m 1,351.50 981.00 13,25,821.50

comprising FR Grade honeycomb structured acoustic panels of standard size 1200 × 1200 × 50 mm or

approved customised sizes, having NRC up to 0.90, UL 94 HF-1 Fire Retardant (Self-Extinguishing)

rating, thermal conductivity not exceeding 0.032 W/m·K, 100% recyclable, CFC-free, low VOC, RoHS &

REACH compliant, moisture resistant and resistant to insects, rodents, bacteria and fungi.

The panels shall be cut to required sizes and securely fixed within the framework using approved

adhesive, GI retainers or other manufacturer-recommended fixing system, complete with all cutting,

fitting, wastage, labour, tools and accessories as per manufacturer's specifications and directions of

the Engineer-in-Charge

106 NS- 47 Providing and fixing full height or low height framed glass partition comprising 12 mm thick clear Sq.m 15,649.00 37.00 5,79,013.00

toughened safety glass of approved make, machine cut, polished and edge-finished on all exposed

edges, fixed within 50 × 50 × 2.0 mm thick powder-coated/anodized aluminium box sections (or

equivalent approved section as per manufacturer's design) all around the perimeter, complete with

glazing gaskets, EPDM/rubber beading, setting blocks, pressure plates, approved silicone sealant,

screws, cleats, brackets, anchor fasteners and all necessary accessories. The item shall include cutting,

fabrication, assembly, alignment, fixing, joint treatment, making good, cleaning and all labour,

materials, tools and tackles complete in accordance with the approved drawings and directions of the

Engineer-in-Charge

107 NS- 48 Providing and fixing back-painted / lacquered glass wall cladding comprising 6 mm thick toughened Sq.m 6,544.10 10.00 65,441.00

clear glass, having back surface factory coated with approved high-quality opaque lacquer/paint in

approved colour and shade, with uniform colour, smooth and defect-free finish, manufactured and

processed to required sizes and shapes as per approved drawings and site conditions. The glass shall

have polished/smooth arrissed edges and shall be fixed over prepared substrate using approved

neutral-cure structural silicone adhesive and/or suitable mechanical fixing system as recommended by

the glass manufacturer, including required setting blocks, spacers, backing/supporting members,

sealants, joints and accessories. All exposed edges, cut-outs, corners, junctions and openings shall be

neatly finished, with accurate alignment, level, plumb and uniform joints. The work shall include

measurement, shop drawings, templates, cutting, edge polishing, toughening, back

painting/lacquering, transportation, handling, protection, installation, cleaning and all necessary

labour, tools, tackles, consumables and incidental materials, complete in all respects as per approved

sample, manufacturer's recommendations and directions of the Engineer-in-Charge/Architect.

9.48 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or -

round bars etc. including priming coat with approved steel primer all complete.

108 9.48.2 Fixed to openings /wooden frames with rawl plugs screws etc. Kg 238.35 100.00 23,835.00

109 10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, Kg 117.35 100.00 11,735.00

hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

110 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., Kg 772.40 100.00 77,240.00

including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting

the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary

accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of

the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for

payment purpose only weight of stainless steel members shall be considered excluding fixing

accessories such as nuts, bolts, fasteners etc.).

111 NS- 49 Providing, supplying and placing free-standing umbrella rack of standard size Ø300 mm × 600 mm No's 14,226.35 1.00 14,226.35

(Height), fabricated from SS 304 stainless steel of minimum 1.2 mm thickness with satin/matte brushed

finish. The rack shall be of cylindrical perforated design with laser-cut circular/oval perforations for

ventilation and aesthetics, complete with removable stainless steel drip tray for water collection,

reinforced top and bottom rings, non-slip rubber floor protectors, smooth polished edges, and all

necessary accessories. The umbrella rack shall have a minimum storage capacity of 10–12 umbrellas,

be corrosion-resistant, easy to maintain, and suitable for use in entrance lobbies, reception areas,

offices, clubs, hotels and other public buildings, complete in all respects as per the approved design

and directions of the Engineer-in-Charge

112 NS- 50 Providing, fabricating, supplying and placing free-standing shoe stand of standard size 900 mm (L) × No's 17,071.65 1.00 17,071.65

350 mm (D) × 900 mm (H), fabricated from MS square hollow sections of 25 × 25 × 1.6 mm and 20 × 20

× 1.6 mm thickness with 1.2 mm thick MS sheet/perforated sheet shelves. The stand shall consist of 4-

tier storage with a capacity of approximately 16–20 pairs of shoes, complete with all welding, grinding,

edge finishing, levelling, rubber/PVC floor protectors, and finished with one coat of zinc-rich metal

primer and two coats of premium grade powder coating of approved colour (minimum 60–80 microns

DFT). The shoe stand shall be sturdy, corrosion-resistant, and complete in all respects as per the

approved design and directions of the Engineer-in-Charge

113 NS- 51 Providing, supplying and fixing decorative photo frame of approved size and design, comprising a rigid Sq.m 5,000.00 25.00 1,25,000.00

MDF/HDHMR board or equivalent substrate with decorative moulded profile/frame made of

PU/polymer/wooden moulding, duly finished with approved colour/finish such as PU paint, duco paint,

melamine or wood finish. Item shall include provision of clear glass/acrylic front cover, high-quality

printed/enlarged photograph/artwork as approved, backing board, required clips/fasteners, wall

mounting hardware, cutting, fabrication, edge finishing and installation complete in all respects, as per

approved design, sample and direction of Engineer-in-Charge

114 NS- 52 Providing, fabricating, supplying and fixing decorative 3D heritage wall relief artwork of approved Sq.m 35,000.00 10.00 3,50,000.00

design, size and pattern, made of FRP moulded panels with required MS/FRP backing support,

incorporating raised figures, motifs and architectural details, finished in approved stone

texture/antique bronze/metallic PU finish, including moulding, surface preparation, painting,

concealed supports, fixing hardware, transportation, lifting, scaffolding, installation, alignment and

cleaning complete in all respects as per approved design and direction of Engineer-in-Charge.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

115 NS- 53 Providing, supplying and placing 52.4 mm thick, 1200 mm high modular partition panels in Wish No's 92,329.10 81.00 74,78,657.10

System, comprising a combination of bottom metal raceway, two intermediate fabric-finished blocks,

and top fabric magnetic tile, complete with panel frame, connectors, clips and all necessary

accessories. The panel shall be designed to accommodate cable management through the integrated

metal raceway and shall be finished with approved fabric upholstery on exposed surfaces.

The panel shall be supported on powder-coated steel legs of approved design and finish, complete

with levellers, fixing hardware, connectors, assembly, transportation, loading, unloading and

placement. The item shall include all fittings, fasteners and incidental works complete in all respects as

per the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

116 NS- 54 Providing, supplying and placing 52.4 mm thick, 1200 mm high modular workstation panel in Wish No's 1,20,027.85 2.00 2,40,055.70

System, comprising a sturdy steel panel frame with a bottom metal raceway for concealed cable

management, two intermediate fabric-finished acoustic blocks, and a top fabric magnetic tile,

complete with all connectors, junctions, end trims, clips and fixing accessories. The panel shall be

supported on powder-coated steel legs with adjustable levellers and finished in approved colour and

fabric. The item shall include complete assembly, transportation, loading, unloading, installation and

all necessary hardware, fittings and incidental works complete in all respects as per the approved

drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

117 NS- 55 Providing, supplying and placing Upbeat Modular Desk Based Workstation of 1200 mm overall height, No's 58,754.90 17.00 9,98,833.30

complete with Cello legs having inclination in one plane and provided with aluminium alloy extrusion

covers in approved colour and finish. The workstation shall be provided with an integrated wire tray

incorporating a power box and switch plate (8+3 Anchor Roma or equivalent), complete with soft-

closing access flap and brush cable manager for concealed cable management.

The workstation shall be provided with a metal modesty panel fabricated from 0.8 mm thick CRCA

steel, securely fixed to the worktop using 3 mm thick HR steel mounting brackets. An 18 mm thick T-

mould fabric screen shall be mounted on studs over the worktop. The worktop shall be 25 mm thick

pre-laminated particle board finished with PVC edge lipping on all exposed edges.

The item shall include all connectors, brackets, hardware, fasteners, levellers, cable management

accessories, assembly, transportation, loading, unloading, installation and all incidental works

complete in all respects as per the approved drawings, manufacturer's specifications and directions of

the Engineer-in-Charge.

118 NS- 56 Providing, supplying and placing Upbeat Modular Desk Based Workstation of 750 mm height, No's 70,505.85 4.00 2,82,023.40

comprising Cello legs with inclination in one plane and aluminium alloy extrusion covers in approved

colour and finish. The workstation shall be provided with an integrated wire management system

consisting of a single power box with raiser for Manager Modules/Single Tables, complete with (8+3

Anchor Roma or equivalent) switch plate, soft-closing access flap and brush cable manager.

The workstation shall be provided with a metal modesty panel fabricated from 0.8 mm thick CRCA

steel, securely mounted to the worktop using 3 mm thick HR steel brackets. The worktop shall be 25

mm thick pre-laminated particle board with PVC edge lipping on all exposed edges.

The item shall include all brackets, connectors, cable management accessories, hardware, fasteners,

levellers, assembly, transportation, loading, unloading, installation and all incidental works complete in

all respects as per the approved drawings, manufacturer's specifications and directions of the Engineer-

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

119 NS- 57 Providing, supplying and placing Mid Back Ergonomic Chair complete with upholstered seat and mesh No's 19,264.90 116.00 22,34,728.40

back, having the following specifications:

The seat shall be manufactured from 15 ± 1 mm thick hot-pressed plywood, upholstered with fabric

and moulded High Resilience (HR) Polyurethane foam, with extra-thick front edge cushioning for

enhanced popliteal comfort. The backrest shall be injection moulded in glass-filled polypropylene

upholstered with mesh fabric, and provided with an adjustable lumbar support made of injection

moulded polypropylene having 50 ± 1 mm adjustment. Seat size shall be 535 mm (W) × 510 mm (D) and

mesh back size 510 mm (W) × 700 mm (H).

The HR Polyurethane seat foam shall have a density of 45 ± 2 kg/m³ and hardness of 16 ± 2 kgf at 25%

compression conforming to IS:7888. The chair shall be provided with height-adjustable armrests having

6-step adjustment with a travel of 72 ± 5 mm, comprising glass-filled nylon armrest structure with PU

moulded arm pads.

The chair shall be fitted with a Centre Tilt Synchro Mechanism with 360° swivel, 3-position locking, anti- -

shock mechanism, and tilt tension adjustment. Pneumatic height adjustment shall provide a stroke of

The pedestal shall be injection moulded in glass-filled nylon, fitted with five twin-wheel nylon castors,

having a pitch centre diameter of 661 ± 5 mm (761 ± 10 mm with castors). Overall chair dimensions

shall be 761 mm (W) × 761 mm (D) × 1015–1110 mm (H) with seat height adjustable from 445 mm to

The item shall include complete assembly, transportation, loading, unloading, placement and all

fittings, accessories and hardware complete in all respects as per the approved drawings,

manufacturer's specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2.

120 NS- 58 Providing, supplying and placing High Back Ergonomic Chair complete with upholstered seat, mesh No's 21,044.30 14.00 2,94,620.20

back and adjustable headrest, having the following specifications:

The seat shall be manufactured from 15 ± 1 mm thick hot-pressed plywood, upholstered with fabric

and moulded High Resilience (HR) Polyurethane foam, with extra-thick front edge cushioning for

enhanced popliteal comfort. The backrest shall be injection moulded in glass-filled polypropylene

upholstered with mesh fabric, and provided with an adjustable lumbar support made of injection

moulded polypropylene having 50 ± 1 mm adjustment. Seat size shall be 535 mm (W) × 510 mm (D) and

mesh back size 510 mm (W) × 700 mm (H).

The HR Polyurethane seat foam shall have a density of 45 ± 2 kg/m³ and hardness of 16 ± 2 kgf at 25%

compression conforming to IS:7888. The chair shall be provided with height-adjustable armrests having

6-step adjustment with a travel of 72 ± 5 mm, comprising glass-filled nylon armrest structure with PU

moulded arm pads.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

The chair shall be fitted with a Centre Tilt Synchro Mechanism featuring 360° swivel, 3-position locking, -

anti-shock mechanism and tilt tension adjustment. It shall also be provided with an adjustable

headrest comprising an injection moulded glass-filled polypropylene frame, upholstered with moulded

HR polyurethane foam and fabric, with a 40 ± 1 mm height adjustment.

The chair shall have pneumatic height adjustment with a stroke of 95 ± 3 mm. The pedestal shall be

injection moulded in glass-filled nylon, fitted with five twin-wheel black nylon castors, having a pitch

centre diameter of 661 ± 5 mm (761 ± 10 mm with castors). Overall chair dimensions shall be 761 mm

(W) × 761 mm (D) × 1170–1300 mm (H) with seat height adjustable from 445 mm to 540 mm.

The item shall include complete assembly, transportation, loading, unloading, placement, all fittings,

accessories and hardware complete in all respects as per the approved drawings, manufacturer's

specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2

121 NS- 59 Providing, supplying and placing Executive Table with ERU (Extended Return Unit) and Integrated No's 1,58,074.15 4.00 6,32,296.60

Pedestal of overall size 1650 × 1950 × 750 mm, complete with the following specifications:

The primary work surface shall be manufactured from 25 mm thick MDF, one side pre-laminated board

conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface and

provided with a soft-closing access flap incorporating an in-built power box for wire management.

The secondary work surface and modesty panel shall be manufactured from 25 mm thick MDF, one

side pre-laminated board conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed

on the top surface.

The understructure and integrated pedestal shall be manufactured from 25 mm thick pre-laminated

Twin Board of E1-P2 Grade, conforming to IS:12823:1990, in approved shade and finished with 2 mm

thick matching PVC edge banding on all exposed edges.

The drawer fronts shall be manufactured from 25 mm thick MDF, one side pre-laminated board -

conforming to IS:14587:1998, with 0.4 mm PVC membrane pressed on the top surface. The integrated

pedestal shall be of Box–Box–File configuration, provided with 400 mm long powder-coated metal

drawer slides having 325 mm drawer extension, complete with soft-closing and anti-slam mechanism,

ergonomic handles and a central locking arrangement for security.

The item shall include all fittings, hardware, power access accessories, connectors, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

122 NS- 60 Providing, supplying and placing Executive Table with ERU (Extended Return Unit) and Integrated No's 1,60,493.20 47.00 75,43,180.40

Pedestal of overall size 1800 × 2100 × 750 mm, complete with the following specifications:

The primary work surface shall be manufactured from 25 mm thick MDF, one side pre-laminated board

conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface and

provided with a soft-closing access flap incorporating an in-built power box for wire management.

The secondary work surface and modesty panel shall be manufactured from 25 mm thick MDF, one

side pre-laminated board conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed

on the top surface.

The understructure and integrated pedestal shall be manufactured from 25 mm thick pre-laminated

Twin Board of E1-P2 Grade, conforming to IS:12823:1990, in approved shade and finished with 2 mm

thick matching PVC edge banding on all exposed edges.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

The drawer fronts shall be manufactured from 25 mm thick MDF, one side pre-laminated board -

conforming to IS:14587:1998, with 0.4 mm PVC membrane pressed on the top surface. The integrated

pedestal shall be of Box–Box–File configuration, provided with 400 mm long powder-coated metal

drawer slides having 325 mm drawer extension, complete with soft-closing and anti-slam mechanism,

ergonomic handles and a central locking arrangement for security.

The item shall include all fittings, hardware, power access accessories, connectors, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

123 NS- 61 Providing, supplying and placing Back Storage Unit of overall size 1650 × 500 × 750 mm, complete with No's 86,139.70 40.00 34,45,588.00

the following specifications:

The top panel shall be manufactured from 25 mm thick MDF, one side pre-laminated board conforming

to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface.

The sliding door storage unit shall be manufactured from 25 mm thick pre-laminated Twin Board of E1-

P2 Grade, conforming to IS:12823:1990, in approved shade, with all body components including side

panels, bottom panel, back panel and shelves finished with 2 mm thick matching PVC edge banding on

The sliding shutters shall be manufactured from 25 mm thick MDF, one side pre-laminated board -

conforming to IS:14587:1998, finished with 0.4 mm PVC membrane pressed on the top surface. The

shutters shall be provided with soft-closing and anti-slam mechanism, ergonomic handles and a locking

arrangement for security.

The item shall include all fittings, hardware, locking system, sliding mechanisms, connectors, assembly,

transportation, loading, unloading, installation and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

124 NS- 62 Providing, supplying and placing High Back Executive Ergonomic Chair complete with leatherette No's 41,580.00 51.00 21,20,580.00

upholstered seat and back, having the following specifications:

The seat assembly shall comprise injection moulded plastic outer and inner shells, with the inner shell

upholstered in leatherette and cushioned with moulded High Resilience (HR) Polyurethane Foam of 45

± 2 kg/m³ density and 16 ± 2 kgf hardness at 25% compression conforming to IS:7888. The back

assembly shall comprise moulded PU foam with an in-situ moulded MS ERW round tube of Ø19 ± 0.3

mm × 1.6 ± 0.128 mm thickness, upholstered in leatherette. Seat size shall be 470 mm (W) × 480 mm

(D) and high back size 477 mm (W) × 764 mm (H).

The chair shall be provided with height-adjustable drop-lift armrests fabricated from Ø38.1 ± 0.3 mm ×

2.0 ± 0.1 mm thick MS ERW tubular supports with chrome-plated finish and PU moulded arm pads,

offering 65 ± 5 mm height adjustment in 5 steps.

The chair shall be fitted with an Active Bio-Synchro Mechanism with 360° swivel, front-pivot -

synchronized tilt, continuous lumbar support, seat/back tilt ratio of 1:2, 5-position tilt limiter, tilt

tension adjustment operable while seated, and black powder-coated HPDC aluminium mechanism

housing. The seat shall incorporate an integrated sliding mechanism providing 60 ± 5 mm seat depth

adjustment. The back support shall be mounted on a plastic T-spine with 74.2 ± 5 mm height

adjustment for personalized lumbar support.

The chair shall be provided with pneumatic height adjustment having a 100 ± 3 mm stroke. The

pedestal shall be manufactured from high-pressure die-cast polished aluminium fitted with five twin-

wheel black polypropylene castors of 60 ± 1 mm diameter, with a pedestal pitch centre diameter of

650 ± 5 mm (750 ± 10 mm with castors).

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

Overall chair dimensions shall be 761 mm (W) × 761 mm (D) × 1127–1302 mm (H) with seat height -

adjustable from 431 mm to 531 mm.

The item shall include complete assembly, transportation, loading, unloading, placement, all fittings,

accessories and hardware complete in all respects as per the approved drawings, manufacturer's

specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2.

125 NS- 63 Providing, supplying and placing Mid Back Executive Ergonomic Chair complete with leatherette No's 38,806.75 153.00 59,37,432.75

upholstered seat and back, having the following specifications:

The seat assembly shall comprise injection moulded plastic outer and inner shells, with the inner shell

upholstered in leatherette and cushioned with moulded High Resilience (HR) Polyurethane Foam of 45

± 2 kg/m³ density and 16 ± 2 kgf hardness at 25% compression conforming to IS:7888. The back

assembly shall comprise moulded PU foam with an in-situ moulded MS ERW round tube of Ø19 ± 0.3

mm × 1.6 ± 0.128 mm thickness, upholstered in leatherette. Seat size shall be 470 mm (W) × 480 mm

(D) and mid back size 477 mm (W) × 601 mm (H).

The chair shall be provided with height-adjustable drop-lift armrests fabricated from Ø38.1 ± 0.3 mm ×

2.0 ± 0.1 mm thick MS ERW tubular supports with chrome-plated finish and PU moulded arm pads,

offering 65 ± 5 mm height adjustment in 5 steps.

The chair shall be fitted with an Active Bio-Synchro Mechanism featuring 360° swivel, front-pivot -

synchronized tilt, continuous lumbar support, 5-position tilt limiter, seat/back tilt ratio of 1:2, tilt

tension adjustment operable while seated, and black powder-coated HPDC aluminium mechanism

housing. The seat shall incorporate an integrated sliding mechanism providing 60 ± 5 mm seat depth

adjustment, while the back support shall be mounted on a plastic T-spine with 74.2 ± 5 mm height

adjustment for optimum ergonomic support.

The chair shall be provided with pneumatic height adjustment having a 100 ± 3 mm stroke. The

pedestal shall be manufactured from high-pressure die-cast polished aluminium fitted with five twin-

wheel black polypropylene castors of 60 ± 1 mm diameter, with a pedestal pitch centre diameter of

650 ± 5 mm (750 ± 10 mm with castors).

Overall chair dimensions shall be 761 mm (W) × 761 mm (D) × 965–1140 mm (H) with seat height

adjustable from 431 mm to 531 mm.

The item shall include complete assembly, transportation, loading, unloading, placement, all fittings,

accessories and hardware complete in all respects as per the approved drawings, manufacturer's

specifications and directions of the Engineer-in-Charge.

The product shall be certified by CII GreenPro, UL GREENGUARD, GRIHA, SCS Indoor Advantage Gold

and BIFMA LEVEL 2.

126 NS- 64 Providing, supplying and placing of one seater sofa. SEAT FOAM : The seat is made up of PU foam in No's 50,297.55 1.00 50,297.55

Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu,

upholstered with fabric or leatherette.

BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer

of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture

resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface

defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for

cushioning purpose.

LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic

Width (W): 86.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

127 NS- 65 Providing, supplying and placing of two seater sofa. SEAT FOAM : The seat is made up of PU foam in No's 65,555.35 2.00 1,31,110.70

Density 28 ±2 kg/cu.mtr with an additional top layer of supersoft PU foam in Density 32 ± 2 kg/cu,

upholstered with fabric or leatherette.

BACK FOAM : The back is made up of PU foam in Density 28 ± 2 kg/cu. mtr with two additional top layer

of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette.

UNDERSTRUCTRE : Understructure is made up of 1.2±0.1 cm. thick hot pressed plywood [moisture

resistance & termite proof as per IS:303] & pinewood of cross sections devoid of major knots & surface

defects. 6 nos. per seat & 3.8mm Dia zigzag spring assembly is mounted over understructure for

cushioning purpose.

LEG ASSEMBLY : It is a welded Assembly made in Stainless steel (grade SS 202) tube & plate with plastic

Width (W): 146.0 CM. Depth (D): 90.5 CM. Height (H): 85.5 CM. Seat Height (SH): 45.0 CM.

128 NS- 66 Providing, supplying and placing of public seating. SEAT SHELL : The Seat is made from high density self- No's 76,942.00 19.00 14,61,898.00

skin Polyurethane foam reinforced with 1.2 mm M.S. perforated sheet insert. The Polyurethane foam

having density of min. 350 kg/m3 with a Shore 'A' hardness of 60±10.

SEAT SIZE : 52.0 cm (W) x 50.5 cm (D)

BACK SHELL : The Back is made from high density self-skin Polyurethane foam reinforced with 1.2 mm

M.S. perforated sheet insert.The Polyurethane Foam having density of min. 350 kg/m3 with a Shore 'A'

hardness of 60±10.

BACK SIZE : 52.0 cm (W) x 53.5 cm (H)

CROSS BEAM : Cross Beam made up of Diamond shaped double wall Extrusion of Aluminum 6063-T6

Alloy with coated of 50 micron epoxy polyester coating and fitted with Polypropylene Copolymer

engineering plastic end caps.

CROSS BEAM SIZE : 11.3 cm (W) x 9.4 cm (H) X 0.4 cm (Thickness).

LEG : Legs are made up of High pressure Aluminum ADC12 Die cast coated with 50 micron epoxy

polyester coating, Leg Are fitted with soft grip PVC level adjusting shoes.

ARMREST : Armrest are made up of High pressure Aluminum ADC12 die cast coated with 50 micron

epoxy polyester coating.

SEAT SUPPORT BRACKET Assembly : Seat support bracket assembly made up of argon shield welding of

Hot Rolled Steel (IS: 2062) 0.3cm Thickness. This welded structure is coated with 50 micron epoxy

polyester coating.

CLAMPING BRACKET : Clamping bracket are made up of Hot Rolled Steel (IS: 2062) 0.3cm Thickness

coated with 50 micron epoxy polyester coating.Overall Dimensions of Chair

Seat Height - 42.5 cm.

Height - 87.0 cm.

Width-165.5cm and Depth-66.5 cm,

The product should be certified by UL GREENGUARD, SCS INDOOR ADVANTAGE GOLD.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

129 NS- 67 Providing, suplying and placing of stoarge unit.Overall Dimensions of SD 2 Single Drive Cover Unit 2 No's 1,03,913.90 1.00 1,03,913.90

Bay(U/C + Fittings + Cover) shall be 2400mm(W) x 400mm(D) x 2113mm(H). The Construction shall be

rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1

main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be

Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend

panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg .

Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS :

2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is

achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly

onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven

rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-

cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and

is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side

of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The

wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller

assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking

arrangement through Lock which is operated by spring mechanism mounted onto understructure of

last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’

arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x

398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable

height on side of the body & projects out of cover by another 99.0 mm. Fixed unit (SD) does not have

the Drive Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last

body. In this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units

shall have Locking Knob near the drive wheel for manual locking of individual units when a person is

using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers

shall be provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

130 NS- 68 Providing, suplying and placing of stoarge unit.Overall Dimensions of LD 2 Single Drive Cover Unit 2 No's 1,79,390.40 1.00 1,79,390.40

Bay(U/C + Fittings + Cover) shall be 2400mm(W) x 400mm(D) x 2113mm(H). The Construction shall be

rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1

main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be

Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend

panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg .

Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS :

2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is

achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly

onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven

rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-

cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and

is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side

of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The

wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller

assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking

arrangement through Lock which is operated by spring mechanism mounted onto understructure of

last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’

arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x

398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable

height on side of the body & projects out of cover by another 99.0 mm. Last unit (LD) have the Drive

Unit Cover. When the last Body is Twin Drive, i.e., TD, hinged doors are provided for the last body. In

this scenario the centralized locking system is fitted on the last TD body. Each Drive Type units shall

have Locking Knob near the drive wheel for manual locking of individual units when a person is using

those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be

provided to prevent derailment.The nuts & bolts are galvanized / blackodized / Zn Plated. Also total

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

131 NS- 69 Providing, suplying and placing of stoarge unit.Overall Dimensions of TD 2 Single Drive Cover Unit 2 No's 2,28,308.05 5.00 11,41,540.25

Bay(U/C + Fittings + Cover) shall be 2400mm(W) x 800mm(D) x 2113mm(H). The Construction shall be

rigid knock down made out of 0.8 thick CRCA steel conforming to IS:513, Gr.D. Each body shall have 1

main unit plus add on units (0,1,2,3 depending on no. of bays 1, 2, 3, 4 respectively) . Finish shall be

Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be with 12 bend

panel made from CRCA steel 0.7 mm thick IS:513, Gr.D .Uniformly distributed load capacity of 100 Kg .

Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick conforming to IS :

2062. The Movements shall be Drive Type configuration : In case of D2,D3 & D4 movement of units is

achieved mechanically through a PU Hand Wheel and Sprocket-Chain arrangement mounted rigidly

onto body size. For D3 each movable undercarriage shall be provided with 3 driving rollers and 3 driven

rollers.LD understructure has 2 nos. of anti-tilt bearing assembly.The roller assembly comprises of a die-

cast step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and

is fitted onto the MS shaft using a feather key. The two ball bearings are then fastened on either side

of the step wheel using circlips. This entire roller assembly is then snap-fitted into a wheel housing. The

wheel housing is fixed in the U-channel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller

assembly is designed to withstand the maximum loads of the body. Fittings shall be centralized locking

arrangement through Lock which is operated by spring mechanism mounted onto understructure of

last drive unit. The lock is made of 0.8 mm thick conforming to IS:513..The ‘sprocket-chain’

arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x

398mm x 87mm and is fixed onto the side of the body. The PU handwheel is rigidly fixed at suitable

height on side of the body & projects out of cover by another 99.0 mm. When the last Body is Twin

Drive, i.e., TD, hinged doors are provided for the last body. In this scenario the centralized locking

system is fitted on the last TD body. Each Drive Type units shall have Locking Knob near the drive wheel

for manual locking of individual units when a person is using those units. Knob shall be rotated to

unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The

nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per

132 NS- 70 Optz Plus Push Pull / D2 CHNL 1600mm -It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm No's 27,290.80 2.00 54,581.60

X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

133 NS- 71 Optz Plus Push Pull / D2 CHNL 2400mm-It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X No's 36,191.35 1.00 36,191.35

2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

134 NS- 72 Supplying and placing in position Main Table of the following specifications.2400 x 900 x 740 MAIN No's 2,29,055.10 16.00 36,64,881.60

WORKTOP :Made of 43mm Thick (±1) combination of MDF and particle board with top veneer

facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneerlipping.

LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface.

Thisleather pad is fixed to main top panel.

DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination

ofMDF and particle board with top veneer face coated with clear lacquer. All thicknessedges are edge

banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on topsurface.

Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is

secured with side central lock.

OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1)

combination of MDF and particle board with top veneer face coated with clear lacquer. Allthickness

edges are edge banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping.

MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Modesty is fitted with

aluminum trims.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door

is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side

panel for security.

ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2

USB powerpoints, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

135 NS- 73 Supplying and placing in position ERU of the following specifications.1200 x 450 x 610 TOP PANEL:Made No's 64,101.60 16.00 10,25,625.60

of 43mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear

lacquer. All edges are edge banded with matching 1mm thick venee rlipping.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.

DOOR PANELS:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approved

shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door is fixed

with soft closing hinges and handle is provided for ease of opening.It is secured with side central lock.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

136 NS- 74 Supplying and placing in position Back unit Body of the following specifications.2400 x 470 x 1226 No's 2,03,281.85 20.00 40,65,637.00

CONSTRUCTION AND MATERIAL:Made from combination of side panel(0.5mm CRCA), Bottom

panel(0.5mm CRCA), Backpanel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End

Cover(0.6mm CRCA).Shelves are 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513).

Storage body is powder coated with Epoxy Polyester to the thickness of 50 microns(+/-10 micron).

VENEER DOOR:Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with

clearlacquer. All edges are edge banded with matching 1mm thick veneer lipping. Door isprovided with

soft closing hinge. Handle is also provided for ease of opening. Storage issecured with 3 way cam lock.

GLASS DOOR:Made from the combination of aluminium alloy (63400) extrusion and 4mm

cleartoughened glass. Aluminium extrusion of glass doors are powder coated with EpoxyPolyester to

the thickness of 50 microns (+/-10 micron). Handle is provided for ease ofopening. RH Glass Door is

provided with 3 way cam lock for security.

Supplying and placing in position Back unit Shutter of the following specifications.2400 x 470 x 1226

CONSTRUCTION AND MATERIAL:Made from combination of side panel(0.5mm CRCA), Bottom

panel(0.5mm CRCA), Backpanel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End

Cover(0.6mm CRCA).Shelves are 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513).

Storage body is powder coated with Epoxy Polyester to the thickness of 50 microns(+/-10 micron).

VENEER DOOR:Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with

clearlacquer. All edges are edge banded with matching 1mm thick veneer lipping. Door isprovided with

soft closing hinge. Handle is also provided for ease of opening. Storage issecured with 3 way cam lock.

GLASS DOOR:Made from the combination of aluminium alloy (63400) extrusion and 4mm

cleartoughened glass. Aluminium extrusion of glass doors are powder coated with EpoxyPolyester to

the thickness of 50 microns (+/-10 micron). Handle is provided for ease ofopening. RH Glass Door is

provided with 3 way cam lock for security.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

137 NS- 75 Supplying and placing in position Main Table of the following specifications.3000 x 1050 x 740 MAIN No's 2,95,550.50 4.00 11,82,202.00

WORKTOP :Made of 43mm Thick (±1) combination of MDF and particle board with top veneer

facecoated with clear lacquer. All edges are edge banded with matching 1mm thick veneerlipping.

LEATHER PAD:Made of 18mm Thick (±1) MDF with Leatherette wrapped around top surface.

Thisleather pad is fixed to main top panel.

DRAWER UNIT:Top panel and drawer unit modesty panel is made of 43mm Thick (±1) combination

ofMDF and particle board with top veneer face coated with clear lacquer. All thicknessedges are edge

banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on topsurface.

Drawer unit is provided with soft closing channels for smooth opening and closing.Drawer unit is

secured with side central lock.

OPEN STORAGE UNIT:Top panel and open storage unit modesty panel is made of 43mm Thick (±1)

combination of MDF and particle board with top veneer face coated with clear lacquer. Allthickness

edges are edge banded with matching lipping.

Remaining construction is of 18mm Pre-laminated twin board (PLT) of E1-P2 grade andapproved shade

confirming to IS-12823:1990, Edge banded with matching 2 mm thickPVC lipping.

MODESTY:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Modesty is fitted with

aluminum trims.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Door

is fixed with soft closing hinges and handle is provided for ease of opening.Also lock is provided on side

panel for security.

ACCESS FLAP WITH POWER BOX:Soft closing access flap with power box contains 3 Universal Sockets, 2

USB powerpoints, 1 HDMI connection, 1 inbuilt misc. cable grommet and CAT 3 and CAT 6connections.

138 NS- 76 Supplying and placing in position ERU of the following specifications.1500 x 600 x 610 TOP PANEL:Made No's 1,12,683.50 4.00 4,50,734.00

of 43mm Thick (±1) combination of MDF and particle board with top veneer facecoated with clear

lacquer. All edges are edge banded with matching 1mm thick veneerlipping.

SLIDING SHUTTER:Made of 12mm Thick (±1) MDF with 3.5mm veneer both side and face coated with

clearlacquer. All thickness edges are edge banded with matching lipping.

Door is provided with soft closing & anti slam mechanism.

Handle is also provided for ease of opening. Storage is secured with lock.

UNDERSTRUCTURE:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and

approvedshade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping.

DRAWERS:Made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade and approvedshade

confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVClipping. Bottom panel of

drawer is 9mm thick particle board with leatherette on topsurface. Drawers have soft closing channels

for smooth opening and closing.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

139 NS- 77 Providing, supplying and placing of High Back Chair. SEAT ASSEMBLY: The Cushioned seat inner is made No's 1,33,138.60 20.00 26,62,772.00

of injection moulded glass filled poly-amide.Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888

for 25% compression.

*Seat SIZE: 45.5cm. (D) x 52.4cm. (W)

BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic

*HIGH BACK SIZE: 50.5 cm. (W) x 76.7 cm. (D)

ARMRESTS: The armrest having four range of adjustment

· Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all other

adjustment are provided in adjustable arm top sub assembly.

· Up-Down adjustment has 8 position (10.5±0.5cm range)

· Arm top swivel adjustment- 2 position, 12°±2° swivel inside

· Arm top width adjustment - Any position (2.0±0.5cm range each arm top)

· Arm top To - Fro Adjustment- any position (4.0±0.5cm range)

· Armrest top is made up of high density PU molded over glass filled Poly-amide inner.

POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following

· 360° revolving type.

· Forward tilt of sesat and back.

· Upright tilt lock.

· Tilt tension adjustment can be operated in seating position.

· 3-position Tilt limiter.

SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated with the

mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0±0.5 cm.

ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

140 NS- 78 Providing, supplying and placing of Mid Back Chair. SEAT ASSEMBLY: The Cushioned seat inner is made No's 1,27,432.65 4.00 5,09,730.60

of injection moulded glass filled poly-amide.Upholstered seat sub-assembly consists of moulded High

Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888

for 25% compression.

*Seat SIZE: 45.5cm. (D) x 52.4cm. (W)

BACK ASSEMBLY: The Cushioned back is made of PU Foam with Polypropylene Injection molded Plastic

*MID BACK SIZE: 50.5 cm. (W) x 61.8cm. (D)

ARMRESTS: The armrest having four range of adjustment

· Height adjustment sub assembly is inserted in the Aluminum Die Cast Arm body & all other

adjustment are provided in adjustable arm top sub assembly.

· Up-Down adjustment has 8 position (10.5±0.5cm range)

· Arm top swivel adjustment- 2 position, 12°±2° swivel inside

· Arm top width adjustment - Any position (2.0±0.5cm range each arm top)

· Arm top To - Fro Adjustment- any position (4.0±0.5cm range)

· Armrest top is made up of high density PU molded over glass filled Poly-amide inner.

POSTURE PERFECT MECHANISM: The adjustable tilting mechanism is designed with the following

· 360° revolving type.

· Forward tilt of sesat and back.

· Upright tilt lock.

· Tilt tension adjustment can be operated in seating position.

· 3-position Tilt limiter.

SEAT DEPTH ADJUSTMENT: Seat depth adjustment is housed below the seat and integrated with the

mechanism with help of Polypropene Seat cover. Seat Depth can be adjusted in sitting position. Seat

depth adjustment range is of 5.0±0.5 cm.

ADJUSTABLE BACK SUPPORT: Back Assembly is connected to buff polish die cast aluminum Spine with

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

141 NS- 79 Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY : The Cushioned seat should No's 1,16,933.25 16.00 18,70,932.00

be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure

leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load

16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded

MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather.

Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D)

BACK SIZE : 47.5 cm. (W) x 77 cm. (D)

ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather

and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x

0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to

6.5±0.5cm in 5 steps.

ACTIVE BIO-SYNCHRO MECHANISM: The adjustable tilting mechanism should be designed with the

following features:

• 360° revolving type.

• Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more

• Tilt tension adjustment can be operated in seating position.

• 5-position Tilt limiter giving option of variable tilt angle to the chair.

• Seat/back tilting ratio of 1: 2

• The mechanism housing should be made up of HPDC Aluminium black powder coated.

SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding

mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.

ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in

Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit

individual need.

PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

142 NS- 80 Providing, supplying and placing of Mid Back Chair. SEAT /BACKASSEMBLY : The Cushioned seat should No's 71,706.15 48.00 34,41,895.20

be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with pure

leather and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load

16 ± 2 kgf for 25% compression.The Cushioned back should be made of PU Foam with insitu molded

MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Pure Leather.

Seat SIZE : 47.6 cm. (W) x 49.2 cm. (D)

BACK SIZE : 46.5 cm. (W) x 59.5 cm. (D)

ARMRESTS: The armrest top should be moulded from polyurethane(PU), upholstered in pure leather

and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x

0.2±0.01 cm thk M.S E.R.W tube having chrome plated finish.The armrest height adjustable up to

6.5±0.5cm in 5 steps.

ACTIVE BIO-SYNCHRO mechanism: The adjustable tiltng mechanism should be designed with the

following features:

• 360° revolving type.

• Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more

• Tilt tension adjustment can be operated in seating position.

• 5-position Tilt limiter giving option of variable tilt angle to the chair.

• Seat/back tilting ratio of 1: 2

• The mechanism housing should be made up of HPDC Aluminium black powder coated.

SEAT DEPTH ADJUSTMENT: Seat depth adjustment should be integrated in the seat through a sliding

mechanism. Seat depth adjustment range should be of 6.0±0.5 cm.

ADJUSTABLE BACK SUPPORT: Back Frame should be connected to the Up/Dn mechanism housed in

Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit

individual need.

PNEUMATIC HT. ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0±0.3

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

143 NS- 81 suplying and placing of storage unit.Overall Dimensions of SS1 - Single Static 1 Bay Push Pull Type (U/C No's 60,131.45 6.00 3,60,788.70

+ Fittings) shall be 1200mm(W)x400mm(D)x2083mm(H). The Construction shall be rigid knock down

made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus add on

units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with

a Dry Film Thickness of minimum 40 microns.Shelf construction made of 0.7 thk CRCA steel conforming

to IS: 513 Gr.D or DD.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have

construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the

system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or

pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at

suitable height on body side. y. Each movable body also has an understructure with 4 nos. of

antifriction ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing

fitted horizontally to restrict the lateral movement of the body on rail while the single moving body,

i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not

only restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement

is provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked

into the channels when all the units are brought together, and the lock is turned. The Recess handle

lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made

of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way

locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated.

Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to

front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the

aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a

transparent plastic of corresponding length of 150-200 micron polythene is to be inserted.

This product should be certified By CII GREENPRO,UL GREENGUARD,UL GREENGUARD GOLD,GRIHA &

SCS INDOOR ADVANTAGE GOLD.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

144 NS- 82 suplying and placing of storage unit.Overall Dimensions of SL1 - Single last 1 Bay Push Pull Type (U/C + No's 72,112.40 6.00 4,32,674.40

Fittings) shall be 1200mm(W)x400mm(D)x2083mm(H). The Construction shall be rigid knock down

made out of 0.8 thick CRCA steel conforming to IS : 513.Each body shall have a main unit plus add on

units (1,2,3,4,5). Final finish consists of epoxy polyester powder coating of approved color & shade with

a Dry Film Thickness of minimum 40 microns.Shelf construction made of 0.7 thk CRCA steel conforming

to IS: 513 Gr.D or DD.Uniformly distributed load capacity of 100 Kg . Undercarriage shall have

construction in welded frame CRCA sheet 2 mmthk conforming to IS:513. The movements of the

system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement of units achieved by pushing or

pulling 'C' tyep plastic handle (mounted on each double & single movable units) & rigidly fixed at

suitable height on body side.Each movable body also has an understructure with 4 nos. of antifriction

ball bearings for rolling on channels. The twin moving body, i.e. TM, has 4 nos. of bearing fitted

horizontally to restrict the lateral movement of the body on rail while the single moving body, i.e. SL,

body has 2 nos. of a special anti-tilt bearing assembly fitted to the understructure which not only

restricts lateral movement but also prevents SL from toppling. A Centralized locking arrangement is

provided through Locking Stiffener mounted onto back of Single Last unit, i.e. SL body. It gets locked

into the channels when all the units are brought together, and the lock is turned. The Recess handle

lock is of Godrej make & placed at a height of 940mm from ground level. The locking stiffener is made

of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die cast Handle cum lock with 3 way

locking through a lever & shooting bolts.The nuts & bolts are galvanized / blackodized / Zn Plated.

Label Holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to

front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the

aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a

transparent plastic of corresponding length of 150-200 micron polythene is to be inserted.

This product should be certified By CII GREENPRO,UL GREENGUARD,UL GREENGUARD GOLD,GRIHA &

SCS INDOOR ADVANTAGE GOLD.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

145 NS- 83 suplying and placing of storage unit.Overall Dimensions of TM1 - Twin Mobile 1 Bay Push Pull Type(U/C No's 1,08,521.95 28.00 30,38,614.60

+ Fittings + Handle) shall be 915mm(W)x762mm(D)x2083mm(H).The Construction shall be rigid knock

down made out of 0.8 thick CRCA steel conforming to IS : 513 . Each body shall have a main unit plus

add on units (1,2,3,4,5) . Finish shall be Epoxy polyester powder coated thickness of 40 microns . Shelf

construction shall be made from CRCA steel 0.7 mm thick IS :513 .Uniformly distributed load capacity of

60 Kg . Undercarriage shall have construction in welded frame CRCA sheet 2 mmthk conforming to

IS:513. TThe movements of the system shall be Push pull configuration (TYPE-P1/TYPE-P2) : Movement

of units achieved by pushing or pulling 'C' tyep plastic handle (mounted on each double & single

movable units) & rigidly fixed at suitable height on body side. Each movable body also has an

understructure with 4 nos. of antifriction ball bearings for rolling on channels. The twin moving body,

i.e. TM, has 4 nos. of bearing fitted horizontally to restrict the lateral movement of the body on rail

while the single moving body, i.e. SL, body has 2 nos. of a special anti-tilt bearing assembly fitted to the

understructure which not only restricts lateral movement but also prevents SL from toppling. A

Centralized locking arrangement is provided through Locking Stiffener mounted onto back of Single

Last unit, i.e. SL body. It gets locked into the channels when all the units are brought together, and the

lock is turned. The Recess handle lock is of Godrej make & placed at a height of 940mm from ground

level. The locking stiffener is made of 1.2 mm thk conforming to IS:513.Hinged doors have Recessed Die

cast Handle cum lock with 3 way locking through a lever & shooting bolts.The nuts & bolts are

galvanized / blackodized / Zn Plated. Label Holder: It is an aluminium extrusion of length 396mm for

LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white

sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and

794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is

to be inserted. // When the last unit is twin movable , hinged doors are provided for the end bodies, so

in this case locking stiffener is mounted onto twin unit.

This product should be certified By CII GREENPRO,UL GREENGUARD,UL GREENGUARD GOLD,GRIHA &

SCS INDOOR ADVANTAGE GOLD.

146 NS- 84 Optz Plus Push Pull / D2 CHNL 800mm-It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X No's 16,261.70 4.00 65,046.80

2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

147 NS- 85 Optz Plus Push Pull / D2 CHNL 1600mm-It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X No's 27,290.80 6.00 1,63,744.80

2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

148 NS- 86 Optz Plus Push Pull / D2 CHNL 2400mm-It consists of ‘C’ section 2 mm thk HR sheet & Square 25.4mm X No's 36,191.35 8.00 2,89,530.80

2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the

help of raul plug & screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm,

1600mm and 2400mm.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

149 NS- 87 Supplying and placing in position conference table of the following specifications with following size No's 4,50,804.45 1.00 4,50,804.45

2 STR MAIN - 1350 x 710 x 740

2 STR SHARED - 1350 x 710 x 740

2 STR END_LH - 1350 x 710 x 740

2 STR END_RH - 1350 x 710 x 740

Work Surface-Made of 36mm thick MDFone side prelaminate board conforming to IS14587:1998 with

0.4mm PVC membrane pressed on to top and having chamfered edge. Full length access panel is

provided with soft closing hinges inline with worktop edge. Worktop is available in various shapes.

Understructure-The understructure consist of mixture of 18mm and 25mm Thick Pre-laminated twin

board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2

mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together.

Modesty-Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.

Wire Management-An array of panels made of 0.8mm and 1.2 mm CRCA MS IS:513, epoxy polyester

powder coated (DFT 40-60 microns) is used for flow of wires and cables. Cutout for Standard Anchor

Roma 4 module is provided for electrical fittings in Straight two seater and single seater modules

below access flap per seat.

AV Details-The table is equipped with Extron cables cubbies along with cable retractors as standard

offering only for 1800mm head module, 2350mm head module, 150° head module and 165° head

module. For straight two seater and single seater modules, provision to mount AV cables is provided

(eg. HDMI,VGAA, etc). Only Corner 90°, 30° corner and 50° corner modules have provision for wire flow

between adjacent tables. Additional Wirecover made of 0.8mm Thick CRCA, provided below worktop

to conceal MicroAV Detailsphone wires running from table top to wire tray.

150 NS- 88 MINGLE UNITISED TABLE - 14 Seater-Work top--Made of 25mm Thick Pre-laminated twin board of E1- No's 2,14,576.20 2.00 4,29,152.40

P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm thick

Soft closing dual access flap provided for access to power supply and data cables.

Understructure-The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board

of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm

thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving

the aesthetics. The product has a knock-down construction.

Wire Management-A wire raiser made of 0.8mm CRCA MS IS:513. It is epoxy polyester powder coated

(DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on either sides for

standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is

provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc).

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

151 NS- 89 Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 No's 33,503.70 42.00 14,07,155.40

±0.1cm. thick hot-pressed plywood & seat is made up of 1.5 ±0.1cm. thick hot-pressed plywood

measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back

foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to

give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra

fluffiness and comfort in chair.

The chair seat & back size are

HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H)

SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density =

45±2 kg/m3 and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression.

ARMRESTS : The 3-way adjustable armrest is is made of die-cast

aluminium with buffing finish designed with the following features :

· Up-Down adjustment–7 steps (7.0 ± 0.5cm range)

· It has to & fro movement along with Swivel adjustment.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following

· 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5

PEDESTAL ASSEMBLY : The pedestal is made of die-cast aluminium with buffing finish. It is fitted with

5nos. twin wheel castor. The pedestal is 67.0 ± 0.5cm pitch-center dia.

(77.0 ± 1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 77.0 CM.

152 NS- 90 Providing, supplying and placing of Visitor Chair. CHAIR UPPERSTRUCTURE: It is a single shell 1.2 No's 12,216.00 3.00 36,648.00

±0.1cm. thick hot pressed plywood

with moulded polyurethane foam on top & backing foam on rear side. It is upholstered with option

of knitted & leatherette fabric.The seat has extra thick foam on front edge to give comfort to

popliteal area.The foam backing done in back ( Executive chairs only) for extra fluffiness and

comfort in chair.

SEAT & BACK HIGH RESILIENCE (HR) POLYURETHANE FOAM :The HR polyurethane foam

for seat and back is moulded with density 45 +/-2 kg/m³ and Hardness load 16 ± 2 kgf as per

IS:7888 at 25% compression.

M.S. VISITOR TUBULAR FRAME (For Thrill Visitore chair): The powder coated (DFT 40-60

micron) tubular frame is cantilever type & made of Ø2.54±0.03 cm x 0.2±0.016 cm thk MS ERW

ARMRESTS:The armrest top is moulded from polyurethane(PU) with metal insert and mounted

on to a tubular frame.

WIDTH (W): 60.5 CM.

DEPTH (D): 65.0 CM.

HEIGHT (H): 86.5 CM.

SEAT HEIGHT (SH): 46.0 CM.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

153 NS- 91 Providing, supplying and placing of storage unit. No's 45,217.75 5.00 2,26,088.75

Overall size Shall be 916mm(W)x486mm(D)x1981mm(H) with welded construction. It should have the

shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and

all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’

grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking

mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall

have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller

with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns

(+/- 10). Plenty of colour options and shelving options shall be available.

The product should be certified by GRIHA.

154 NS- 92 Providing, supplying and placing Cedar Three Seater Sofa of overall size 1920 mm (W) × 860 mm (D) × No's 1,23,808.30 1.00 1,23,808.30

880 mm (H) with seat height of 450 mm, complete with a sturdy Sheesham wood frame and premium

fabric upholstery of approved colour and finish, suitable for office, lounge and waiting areas.

The sofa shall feature a distinctive mid-back design with a curved backrest and angular Sheesham

wood armrests. The primary structure shall be manufactured from seasoned Sheesham wood, ensuring

high strength, dimensional stability and natural resistance to insects, fungus and mould.

The seat cushions shall be provided with high-density polyurethane foam, while the back cushions shall

be filled with Recron fibre for enhanced comfort and ergonomic support. The upholstery shall be of

premium quality fabric with neat tailoring and superior finish.

The item shall include complete frame, cushions, upholstery, fittings, hardware, assembly,

transportation, loading, unloading, placement and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge

155 NS- 93 Providing, supplying and placing Cedar Single Seater Sofa of overall size 860 mm (W) × 640 mm (D) × No's 59,001.65 3.00 1,77,004.95

880 mm (H) with seat height of 450 mm, complete with a sturdy Sheesham wood frame and premium

fabric upholstery, suitable for office, lounge and waiting areas.

The sofa shall feature a distinctive mid-back design with a curved backrest and angular Sheesham

wood armrests. The primary structure shall be manufactured from seasoned Sheesham wood,

naturally resistant to insects, fungus and mould, ensuring long-term durability and stability.

The seat cushion shall be provided with high-density polyurethane foam, while the back cushion shall

be filled with Recron fibre for enhanced comfort and support. The upholstery shall be of premium

quality fabric in approved colour and finish. The unit shall be supplied in knock-down (KD) condition

and assembled at site.

The item shall include complete frame, cushions, upholstery, fittings, hardware, assembly,

transportation, loading, unloading, placement and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

156 NS- 94 Providing, supplying and placing Majesta Plus 2-Seater Sofa of approved size, colour and finish, No's 1,12,777.50 8.00 9,02,220.00

complete with a solid hardwood frame and premium upholstery, suitable for office, lounge and waiting

The sofa shall be fabricated with a solid wood frame reinforced with plywood cross members,

seasoned to a maximum 12% moisture content for dimensional stability and durability. The seat and

back shall be cushioned with high-density polyurethane foam of minimum 28 kg/m³ density, supported

on S-spring webbing to provide enhanced seating comfort and long service life.

The upholstery shall comprise premium composite leather, consisting of 1.0 mm thick genuine

pigmented leather at all contact surfaces including the seat and backrest, and 1.0 mm thick matching

PVC synthetic leather at non-contact surfaces. The sofa shall be finished in the approved Cherry shade

or as directed by the Engineer-in-Charge.

The sofa shall be supported on rubber wood legs with suitable protective floor glides and shall include

all fittings, hardware, assembly, transportation, loading, unloading, placement and all incidental works

complete in all respects as per the approved drawings, manufacturer's specifications and directions of

the Engineer-in-Charge.

157 NS- 95 Providing, supplying and placing 2-Seater Sofa of overall size 1275 mm (W) × 800 mm (D) × 835 mm (H) No's 37,433.60 7.00 2,62,035.20

with seat height of 465 mm, complete with sturdy internal frame and upholstered in premium quality

synthetic leather (leatherette) of approved colour and finish.

The sofa shall feature an aesthetically designed mid-back backrest with decorative tufting and clean

stitching, ergonomically shaped rounded armrests, and high-density soft foam seat and back cushions

for enhanced comfort. The upholstery shall be easy to clean, durable, abrasion-resistant and suitable

for heavy indoor commercial use.

The item shall include all materials, internal frame, cushioning, upholstery, fittings, assembly,

transportation, loading, unloading, placement and all incidental works complete in all respects as per

the approved drawings, manufacturer's specifications and directions of the Engineer-in-Charge. The

product shall be supplied with a minimum 1-year manufacturer's warranty against manufacturing

158 NS- 96 Providing, fabricating, supplying and fixing premium Executive Office Table of size 2400 × 1200 × 750 No's 3,55,659.15 4.00 14,22,636.60

mm, made of First Class seasoned Teak Wood (TW) framework, 25 mm & 19 mm BWP Grade Marine

Plywood (IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid

teak wood decorative mouldings, edge lipping, drawers, cabinets, modesty panel, cable management,

premium hardware, central locking system, telescopic channels, soft-close hinges, and 3-coat PU

polish. with 8mm thk glass top with bevelling, The rate shall include all materials, labour, hardware,

polishing, transportation, installation, testing, wastage, all leads & lifts, and complete in all respects as

per approved drawing and direction of the Engineer-in-Charge

159 NS- 97 Providing, fabricating, supplying and fixing premium Executive Office Table of size 2100 × 900 × 750 No's 3,41,432.75 16.00 54,62,924.00

mm,made of First Class seasoned Teak Wood (TW) framework, 25 mm & 19 mm BWP Grade Marine

Plywood (IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid

teak wood decorative mouldings, edge lipping, drawers, cabinets, modesty panel, cable management,

premium hardware central locking system, telescopic channels, soft-close hinges, and 3-coat PU

polish. with 8mm thk glass top with bevelling, The rate shall include all materials, labour, hardware,

polishing, transportation, installation, testing, wastage, all leads & lifts, and complete in all respects as

per approved drawing and direction of the Engineer-in-Charge

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

Providing, fabricating, supplying and fixing premium Centre Table of size 900 × 600 × 450 mm, made of

First Class seasoned Teak Wood (TW) framework, 25 mm & 19 mm BWP Grade Marine Plywood

(IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid teak wood

decorative mouldings, edge lipping, carved profiles, concealed joinery and premium PU polish. The rate

shall include all materials, premium hardware, adhesives, polishing, transportation, labour,

installation, wastage, all leads & lifts and complete in all respects as per approved drawings and

direction of the Engineer-in-Charge.

Providing, fabricating, supplying and fixing premium Side Table of size 600 × 600 × 450 mm, made of

First Class seasoned Teak Wood (TW) framework, 25 mm & 19 mm BWP Grade Marine Plywood

(IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid teak wood

decorative mouldings, edge lipping, carved profiles, concealed joinery and premium PU polish. The rate

shall include all materials, premium hardware, adhesives, polishing, transportation, labour,

installation, wastage, all leads & lifts and complete in all respects as per approved drawings and

direction of the Engineer-in-Charge.

Providing, fabricating, supplying and fixing premium TV/Console Unit of size 1800 × 600 × 900 mm,

made of First Class seasoned Teak Wood (TW) framework, 25 mm & 19 mm BWP Grade Marine

Plywood (IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid

teak wood decorative mouldings, edge lipping, drawers, shutters, adjustable shelves, cable

management provision, concealed joinery, premium hardware soft-close hinges, telescopic channels,

magnetic catches, and 3-coat premium PU polish. The rate shall include all materials, hardware,

polishing, transportation, labour, installation, testing, wastage, all leads & lifts, and complete in all

respects as per approved drawings and direction of the Engineer-in-Charge.

Providing, fabricating, supplying and fixing premium Back Credenza of size 2400 × 500 × 750 mm, made

of First Class seasoned Teak Wood (TW) framework, 25 mm, 19 mm & 12 mm BWP Grade Marine

Plywood (IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid

teak wood decorative mouldings, edge lipping, openable shutters, adjustable shelves, concealed

joinery, premium hardware soft-close concealed hinges, telescopic channels (where required),

magnetic catches, locking arrangement, adjustable levelling feet, and 3-coat premium PU polish. The

rate shall include all materials, hardware, polishing, transportation, labour, installation, testing,

wastage, all leads & lifts, and complete in all respects as per approved drawings and direction of the

Engineer-in-Charge.

Digitally signed by SUJEET

SR.NO CPWD DSR DESCRIPTION OF ITEMS UNIT RATE TOTAL QTY AMOUNT AS PER CPWD AMOUNT AS PER NON

2023 DSR 2023 ITEMS DSR ITEMS

Providing, fabricating, supplying and fixing premium Side Credenza of size 1200 × 450 × 750 mm, made

of First Class seasoned Teak Wood (TW) framework, 25 mm, 19 mm & 12 mm BWP Grade Marine

Plywood (IS:710), finished with 0.6 mm thick natural veneer on all exposed surfaces, including solid

teak wood decorative mouldings, edge lipping, openable shutters, adjustable shelves, concealed

joinery, premium hardware soft-close concealed hinges, magnetic catches, locking arrangement,

adjustable levelling feet, and 3-coat premium PU polish. The rate shall include all materials, hardware,

polishing, transportation, labour, installation, testing, wastage, all leads & lifts, and complete in all

respects as per approved drawings and direction of the Engineer-in-Charge

APPLYING COST INDEX OF 1.17 ON CPWD DSR 2023 ITEMS & GST CORRECTION FACTOR 0.973 ON A 2,04,14,981.62 19,84,10,411.46

GRAND TOTAL 21,88,25,393.07

GRAND TOTAL 21,88,25,393.07

Digitally signed by SUJEET

REPAIRS, RETROFITTING, REFURBISHMENT, UPGRADATION AND FURNISHING FOR VIJAYDEEP BUILDING AND PORT BHAVAN

OF MUMBAI PORT AUTHORITY

SR.NO PARTICULAR AMOUNT AS PER CPWD DSR AMOUNT AS PER NON DSR ITEMS

TOTAL COST WITH GST 2,33,55,586.31

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

PLUMBING WORKS'

Note: 1) All Sanitary fixture, Water supply fixture & all equipments shall be as

per GRIHA requirement compliance

1.00 17 SUB HEAD- SANITARY INSTALLATIONS

(CPWD DSR 2023)

1.01 17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 1.00 Each 6,945.00 6,945.00 6,945.00 `

(CPWD DSR 2023) with C.I. brackets and stainless steel plug 40 mm, including painting of fittings

and brackets, cutting and making good the walls wherever required :

Kitchen sink with drain board 510x1040 mm bowl depth 250 mm

1.02 17.10.2.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 2.00 Each 4,940.80 9,881.60 9,881.60

(CPWD DSR 2023) with C.I. brackets and stainless steel plug 40 mm, including painting of fittings

and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board 610x510 mm bowl depth 200 mm

1.03 NS- 1 Providing and fixing HDPE pipes complete with HDPE fittings with EN 12056 in 105.00 Metre 1,770.60 1,85,913.00 1,85,913.00

conjunction with DIN 1986-100 and EN 752,Linear expansion: 0.17 mm/m*K.

Temperature resistance: up to 80 °C, short-term 100 °C. Building material class:

DIN 4102-B2, normally inflammable complete as directed by Engineer-in-

Charge.50 mm dia nominal bore

1.04 NS- 2 Providing and fixing HDPE pipes complete with HDPE fittings with EN 12056 in 443.75 Metre 2,180.20 9,67,463.75 9,67,463.75

conjunction with DIN 1986-100 and EN 752,Linear expansion: 0.17 mm/m*K.

Temperature resistance: up to 80 °C, short-term 100 °C. Building material class:

DIN 4102-B2, normally inflammable complete as directed by Engineer-in-

Charge.80 mm dia nominal bore

1.05 NS- 3 Providing and fixing HDPE pipes complete with HDPE fittings with EN 12056 in 406.25 Metre 6,542.10 26,57,728.13 26,57,728.13

conjunction with DIN 1986-100 and EN 752,Linear expansion: 0.17 mm/m*K.

Temperature resistance: up to 80 °C, short-term 100 °C. Building material class:

DIN 4102-B2, normally inflammable complete as directed by Engineer-in-

Charge.100 mm dia nominal bore

1.06 NS- 4 Providing and fixing HDPE pipes complete with HDPE fittings with EN 12056 in 505.00 Metre 8,850.65 44,69,578.25 44,69,578.25

conjunction with DIN 1986-100 and EN 752,Linear expansion: 0.17 mm/m*K.

Temperature resistance: up to 80 °C, short-term 100 °C. Building material class:

DIN 4102-B2, normally inflammable complete as directed by Engineer-in-

Charge.150 mm dia nominal bore

1.07 NS- 5 Providing and fixing 75mm dia Nahani Trap / Multi Nahani Trap with minimum 68.00 Nos 3,496.00 2,37,728.00 2,37,728.00

50 mm water seal, including jointing, testing, making connections to the waste

pipe system, cutting and making good, complete as directed by the Engineer-in-

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

1.08 R3-CS-PS- 218-a Supplying &Fixing screwed cast brass cleanout plug with suitable inset keys & 45.00 Nos 1,801.00 81,045.00 81,045.00

(MCGM SOR 23-24) opening, male threaded joint with EPDM rubber gasket jointng as pe DIN-

1.09 R3-CS-PS- 218-b Supplying &Fixing screwed cast brass cleanout plug with suitable inset keys & 45.00 Nos 2,123.00 95,535.00 95,535.00

(MCGM SOR 23-24) opening, male threaded joint with EPDM rubber gasket jointng as pe DIN-

1.10 R3-CS-PS- 218-c Supplying &Fixing screwed cast brass cleanout plug with suitable inset keys & 45.00 Nos 4,055.00 1,82,475.00 1,82,475.00

(MCGM SOR 23-24) opening, male threaded joint with EPDM rubber gasket jointng as pe DIN-

1.11 NS- 6 Providing and fixing GI Anchor Fastner 12mm dia,GI threaded rod 12mm dia,& 90.00 Each 267.60 24,084.00 24,084.00

GI Hanger clamp with nuts and washer of required size for ceiling suspended

pipe complete as per direction of Engineer-in-charge.

1.12 17.77 Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/

(CPWD DSR 2023) cast iron (spun) pipes comprising of the help of galavinized iron of 6mm of

required size brackets made of 50x5 mm flat of specified shape, projecting 75

mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion

hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface

and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets

with the help of G.I U bolts of 6mm dia of required of size Nuts & washers.

A 17.77.1 Total bracket length 580 mm of approved shape and design (for single 71.00 Each 304.05 21,587.55 21,587.55

(CPWD DSR 2023) 150/100/75mm dia pipe)

B 17.77.2 Total bracket length 810 mm of approved shape and design (for two 71.00 Each 378.10 26,845.10 26,845.10

(CPWD DSR 2023) 150/100/75mm dia pipes)

C 17.77.3 Total bracket length 1040 mm of approved shape and design (for three 71.00 Each 451.90 32,084.90 32,084.90

(CPWD DSR 2023) 150/100/75mm dia pipes)

1.13 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 3.00 No 6,767.40 20,302.20 20,302.20

(CPWD DSR 2023) 100 mm sand cast Iron P or S trap, and Metropole Flush Valve Dual Flow 32Mm

Size (Concealed Body) With Exposed Shut Off Provision (2.0/4.0 Lts. Per Flushing)

with all fittings and fixures complete including cutting and making good the wall

and floors wherever required complete as directed by Engineer-in-Charge

(Contractor Shall Provide 10 year Warrantee certificate and Manufacturer's Test

Certificate including copy of invoice of each item).

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral

type foot rests

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

1.14 NS- 7 Providing and fixing white vitreous china Rimless Wall Hung Wc With Uf Soft 13.00 Each 15,470.48 2,01,116.24 2,01,116.24

Close Slim Seat Cover, Hinges, Accessories Set, Size: 380X515X360 and

Metropole Flush Valve Dual Flow 32Mm Size (Concealed Body) With Exposed

Shut Off Provision (2.0/4.0 Lts. Per Flushing) with all fittings and fixures

complete including cutting and making good the wall and floors wherever

required complete as directed by Engineer-in-Charge (Contractor Shall Provide

10 year Warrantee certificate and Manufacturer's Test Certificate including copy

of invoice of each item).

1.15 NS- 8 Providing and fixing white vitreous china square Under Counter Basin With 16.00 SET 4,468.81 71,500.96 71,500.96

Fixing Accessories, Size: 485X370X205 Mm, Shape: Rectangular , with Waste

Coupling 32Mm Size Half Thread With 80Mm Height , basin waste 32mm size

with 300 mm &190 mm long wall connections pipe and wall flange , Bottle

Trap (With Internal Partition) 32Mm Size With 250Mm & 190Mm Long Wall

Connection Pipes & Wall Flange and with painting complete including cutting

and making good the walls where required complete as directed by Engineer-in-

Charge(Contractor Shall Provide 10 year Warrantee certificate and

Manufacturer's Test Certificate including copy of invoice of each item).

1.16 NS- 9 Providing and fixing white vitreous china Wall Hung Flat Back Urinal (Back Inlet) 12.00 SET 21,688.50 2,60,262.00 2,60,262.00

With Fixing Accessories, Size: 385X325X635 Mm and Sensor Concealed Type

Flush Valve For Urinal Complete Set With Installation Box & Control Valve

With 1.5 Lpf At 3 Bar Pressure (9V Transformer) with all fittings and fixures

complete including cutting and making good the wall and floors wherever

required complete as directed by Engineer-in-Charge (Contractor Shall Provide

10 year Warrantee certificate and Manufacturer's Test Certificate including copy

of invoice of each item).

1.17 NS- 10 Providing and fixing white vitreous china Rimless Blind Installation Wall Hung 15.00 SET 19,083.56 2,86,253.40 2,86,253.40

Wc With Uf Soft Close Slim Seat Cover, Hinges And Accessories Set, Size:

380X525X375 Mm and Pressmatic flush valve capcity 2 litre/4 litre make with

all fittings and fixures complete including cutting and making good the wall and

floors wherever required complete as directed by Engineer-in-Charge

(Contractor Shall Provide 10 year Warrantee certificate and Manufacturer's Test

Certificate including copy of invoice of each item).

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

1.18 NS- 11 Providing and fixing white vitreous china Thin Rim Table Top Basin, 16.00 SET 7,078.83 1,13,261.28 1,13,261.28

Size:495X395X150 Mm, Shape - Rectangular of make,with Click Clack Waste

32Mm Size Full Thread With 130Mm Height ,Bottle Trap (With Internal

Partition) 32Mm Size With 250Mm & 190Mm Long Wall Connection Pipes &

Wall Flange and with painting complete including cutting and making good the

walls where required complete as directed by Engineer-in-Charge(Contractor

Shall Provide 10 year Warrantee certificate and Manufacturer's Test Certificate

including copy of invoice of each item).

1.19 NS- 12 Providing and fixing white vitreous china Rimless Wall Hung Wc With Uf Soft 3.00 SET 24,211.24 72,633.72 72,633.72

Close Slim Seat Cover, Hinges, Accessories Set, Size: 380X515X360 Mm and

with Sensor Concealed Type Flushing Valve For Western Commode Complete

Set With Provision For Manual Operation Also & Flow Restrictor 4.0 Lpf At 3

Bar Pressure (Battery Operated) with all fittings and fixures complete including

cutting and making good the wall and floors wherever required complete as

directed by Engineer-in-Charge (Contractor Shall Provide 10 year Warrantee

certificate and Manufacturer's Test Certificate including copy of invoice of each

1.20 NS- 13 Supplying and fixing in position 600 x 450mm MD 12.5 MT FRP Gratings for 166.67 each 3,884.10 6,47,350.00 6,47,350.00

storm water drain in requred sizes, thickness and shapes as per the Architectural

drawing etc. all complete as per direction of Engineer-in-charge.

1.21 NS- 14 Providing and fixing factory made precast FRP drain covers with frame, having 15.00 each 4,150.05 62,250.75 62,250.75

strength of 5 ton, of size 450 x 900 complete, all as per direction of Engineer-in-

1.22 NS- 15 Providing and fixing factory made precast FRP drain covers with frame, having 10.00 each 5,909.75 59,097.50 59,097.50

strength of 5 ton, of size 600 x 900 complete, all as per direction of Engineer-in-

1.23 12.41 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring conforming to

IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

(CPWD DSR 2023)

(CPWD DSR 2023)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

1.24 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/

(CPWD DSR 2023) accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592

Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm

gap for thermal expansion.

1.25 12.42.1 Coupler

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

1.26 12.42.4 Single tee without door

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

1.28 12.42.6 Shoe (Plain)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

1.29 R3-CS-PS-259 Providing & Fixing 100mm diameter Nahani trap Jali in steel finish with 68.00 Each 437.00 29,716.00 29,716.00

(MCGM SOR 23-24) necessary fixing required to make the item well functional.

2.00 18 SUB HEAD- WATER SUPPLY

(CPWD DSR 2023)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

2.01 18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

(CPWD DSR 2023) stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement and testing of

joints complete as per direction of Engineer in Charge.Internal work - Exposed

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

2.01 18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

(CPWD DSR 2023) stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of joints complete as per

direction of Engineer in Charge. Concealed work, including cutting chases and

making good the walls etc.

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

2.02 NS- 20 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal 138.00 Metre 1,175.95 1,62,281.10 1,62,281.10

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of joints complete as per

direction of Engineer in Charge. Concealed work, including cutting chases and

making good the walls etc.

40 mm nominal outer dia Pipes

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

2.03 NS- 21 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal 144.00 Metre 1,730.15 2,49,141.60 2,49,141.60

stability for hot & cold water supply, including all CPVC plain & brass threaded

fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of

pipes & fittings with one step CPVC solvent cement and the cost of cutting

chases and making good the same including testing of joints complete as per

direction of Engineer in Charge. Concealed work, including cutting chases and

making good the walls etc.

50 mm nominal outer dia Pipes

2.04 18.9 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

(CPWD DSR 2023) stability for hot & cold water supply including all CPVC plain & brass threaded

fittings This includes jointing of pipes & fittings with one step CPVC solvent

cement, trenching, refilling & testing of joints complete as per direction of

Engineer in Charge.

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

2.05 18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting

(CPWD DSR 2023) and making good the walls etc. Internal work - Exposed on wall

(CPWD DSR 2023)

(CPWD DSR 2023)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

2.06 NS- 22 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting 96.00 Metre 1,189.10 1,14,153.60 1,14,153.60

and making good the walls etc. Internal work - Exposed on wall

65 mm dia nominal bore

2.07 NS- 23 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting 132.00 Metre 1,467.95 1,93,769.40 1,93,769.40

and making good the walls etc. Internal work - Exposed on wall

80 mm dia nominal bore

2.08 NS- 24 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting 96.00 Metre 1,865.60 1,79,097.60 1,79,097.60

and making good the walls etc. Internal work - Exposed on wall

100 mm dia nominal bore

2.09 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and

(CPWD DSR 2023) refilling etc. External work

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

2.10 27.11 Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating

(CPWD M&E 2025) with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers,

gaskets conforming to IS 13095 of following sizes as required:

(CPWD M&E 2025)

(CPWD M&E 2025)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

(CPWD M&E 2025)

(CPWD M&E 2025)

2.11 27.14 Providing, installation, testing and commissioning of non-return valve of

(CPWD M&E 2025) following sizes confirming to IS: 5312 complete with rubber gasket, Gl bolts,

nuts, washers etc. as required:

(CPWD M&E 2025)

(CPWD M&E 2025)

(CPWD M&E 2025)

(CPWD M&E 2025)

(CPWD M&E 2025)

2.12 27.15 Providing, installation, testing and commissioning of stainless steel Y-strainer

(CPWD M&E 2025) fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia

holes with stainless steel flange.

(CPWD M&E 2025)

(CPWD M&E 2025)

(CPWD M&E 2025)

2.13 18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic

(CPWD DSR 2023) paint of approved quality :

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

(CPWD DSR 2023)

2.14 18.41 Providing and filling sand of grading zone V or coarser grade, allround the G.I.

(CPWD DSR 2023) pipes in external work :

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

2.15 18.21 Providing and fixing uplasticised PVC connection pipe with brass unions.This

(CPWD DSR 2023) includes jointing of pipes & required all fittings complete as per direction of

Engineer in Charge.

18.21.2 45 cm length

(CPWD DSR 2023)

(CPWD DSR 2023)

2.16 18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the

(CPWD DSR 2023) pipe and making long screws etc. complete (New work) :

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

(CPWD DSR 2023)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

(CPWD DSR 2023)

(CPWD DSR 2023)

2.17 NS- 25 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the 90.00 Each 1,270.35 1,14,331.50 1,14,331.50

pipe and making long screws etc. complete (New work) :

100 mm dia nominal bore

2.18 NS- 26 Providing and fixing of pressure reducing station with 1nos pressure reducing 1.00 Each 16,191.60 16,191.60 16,191.60

valve, 1 nos pressure relief valve, 2 nos pressure gauge, 3 nos ball valve, 1 nos

strainer,bypass arrangement complete as per standard drawing and complete as

per the direction of Engineer-in-charge. 25 mm dia nominal bore.

2.19 NS- 27 Providing and fixing of pressure reducing station with 1nos pressure reducing 1.00 Each 19,995.75 19,995.75 19,995.75

valve, 1 nos pressure relief valve, 2 nos pressure gauge, 3 nos ball valve, 1 nos

strainer,bypass arrangement complete as per standard drawing and complete as

per the direction of Engineer-in-charge. 32 mm dia nominal bore.

2.20 NS- 28 Providing and fixing of pressure reducing station with 1nos pressure reducing 1.00 Each 33,079.45 33,079.45 33,079.45

valve, 1 nos pressure relief valve, 2 nos pressure gauge, 3 nos ball valve, 1 nos

strainer,bypass arrangement complete as per standard drawing and complete as

per the direction of Engineer-in-charge. 40 mm dia nominal bore.

2.21 NS- 29 Providing and fixing of pressure reducing station with 1nos pressure reducing 1.00 Each 41,301.15 41,301.15 41,301.15

valve, 1 nos pressure relief valve, 2 nos pressure gauge, 3 nos ball valve, 1 nos

strainer,bypass arrangement complete as per standard drawing and complete as

per the direction of Engineer-in-charge. 50 mm dia nominal bore.

2.22 NS- 30 Providing and fixing gun metal ball valve of approved quality : 41.00 Each 447.90 18,363.90 18,363.90

20 mm nominal bore

2.23 NS- 31 Providing and fixing gun metal ball valve of approved quality : 51.00 Each 516.25 26,328.75 26,328.75

25 mm nominal bore

2.24 NS- 32 Providing and fixing gun metal ball valve of approved quality : 66.00 Each 572.10 37,758.60 37,758.60

32mm nominal bore

2.25 NS- 33 Providing and fixing gun metal ball valve of approved quality : 47.00 Each 685.05 32,197.35 32,197.35

40 mm nominal bore

2.26 NS- 34 Providing and fixing gun metal ball valve of approved quality : 49.00 Each 850.75 41,686.75 41,686.75

50 mm nominal bore

2.27 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality

(CPWD DSR 2023) (screwed end) :

(CPWD DSR 2023)

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

2.28 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage 30,000.00 ltr 11.00 3,30,000.00 3,30,000.00

(CPWD DSR 2023) tank, IS : 12701 marked, with cover and suitable locking arrangement and

making necessary holes for inlet, outlet and overflow pipes but without fittings

and the base support for tank.

2.29 18.48A Providing and fixing rectangular high density polyethylene water storage loft 2,000.00 ltr 11.00 22,000.00 22,000.00

(CPWD DSR 2023) tank with cover, conforming to ISI : 12701, colour of opaque white or as

approved by Engineer-in-charge. The rate includes making necessary holes for

inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank

shall be paid separately.

2.30 18.59 Providing and fixing C.I. double acting air valve of approved quality with bolts,

(CPWD DSR 2023) nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will

be paid separately) :

(CPWD DSR 2023)

2.31 18.60 Providing and fixing enclosed type water meter (bulk type) conforming to IS :

(CPWD DSR 2023) 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions

etc. (The tail pieces if required will be paid separately) :

(CPWD DSR 2023)

(CPWD DSR 2023)

2.32 18.61 Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts,

(CPWD DSR 2023) bolts, rubber insertions etc. complete conforming to IS : 2373 :

(CPWD DSR 2023)

(CPWD DSR 2023)

2.33 3-3-8 Supplying, erecting, testing and commissioning self contained water cooler 3.00 Each 40,830.36 1,22,491.08 1,22,491.08

(PWD SSR 23-24) 230/250V 50 cycles nominal cooling capacity of 40 litres per hour and storage

capacity 80 litres with partially stainless steel body As per specification No.

2.34 3-1-6 Supplying and erecting midget type 3.0 litres instant type water heater of 4.00 Each 5,267.52 21,070.08 21,070.08

(PWD SSR 23-24) rustproof & shockproof ABS plastic body, high grade SS inner tank & 3kW

heating element with corrosion & hard water protection, with minimum 3 safety

protections (i.e. thermostat & thermal function valve) complete with 6.5 bar

pressure withstanding capacity 230/250V, 50Hz, A.C. supply with inlet and

outlet, with 3 core PVC flexible copper wire leads duly tested and marking sr. no.

and date of erection complete.

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER

2023/PWD 23- CPWD DSR 2023 NON DSR ITEMS

24/MCGM23- ITEMS

2.35 NS- 35 Providing and fixing C.P. brass 2 Way Bib Cock With Wall Flange And Flow 31.00 Each 2,105.49 65,270.19 65,270.19

Restrictor 6.0 Lpm At 3 Bar Pressure complete as directed by Engineer-in-

Charge (Contractor Shall Provide 10 year Warrantee certificate and

Manufacturer's Test Certificate including copy of invoice of each item).

2.36 NS- 36 Providing and fixing C.P. brass Health Faucet With 8Mm Dia, 1 Meter Long 31.00 Each 1,738.30 53,887.30 53,887.30

Flexible Tube & Wall Hook With N.R.V & Flow Restrictor 3.8 Lpm At 3 Bar

Pressure (Back Flow Preventer) including cutting and making good the walls

wherever required complete as directed by Engineer-in-Charge (Contractor Shall

Provide 10 year Warrantee certificate and Manufacturer's Test Certificate

including copy of invoice of each item).

2.37 NS- 37 Providing and fixing toilet paper holder with stainless steel Flap complete as 31.00 Each 755.80 23,429.80 23,429.80

per direction of Engineer-in-charge (Contractor Shall Provide 10 year

Warrantee certificate and Manufacturer's Test Certificate including copy of

invoice of each item).

2.38 NS- 38 Providing and Fixing of Robe Hook fixed to PVC cleats with C.P. brass screws 68.00 Each 331.14 22,517.52 22,517.52

including cutting and making good the walls wherever required etc complete

as per the direction of Engineer - in - Charge.

2.39 NS- 39 Providing and fixing 15mm C.P. brass Pillar Cock Auto Closing System With 16.00 Each 3,109.75 49,756.00 49,756.00

65Mm Extension Body & Flow Restrictor 6.0 Lpm At 3 Bar Pressure with

including cutting and making good the walls wherever required complete as

directed by Engineer-in-Charge (Contractor Shall Provide 10 year Warrantee

certificate and Manufacturer's Test Certificate including copy of invoice of each

2.40 NS- 40 Providing and fixing Angle cock with including cutting and making good the 19.00 Each 563.00 10,697.00 10,697.00

walls wherever required complete as directed by Engineer-in-Charge (Contractor

Shall Provide 10 year Warrantee certificate and Manufacturer's Test Certificate

including copy of invoice of each item).

2.41 NS- 41 Providing & fixing of approved Liquid Soap Dispenser With Glass Bottle with 27.00 Each 1,385.30 37,403.10 37,403.10

necessary fittings and screws etc. all complete as per the direction of Engineer-in-

Digitally signed by SUJEET

BILL OF QUANTITES (PLUMBING WORKS)

SR.NO CPWD DSR DESCRIPTION OF ITEMS QUANTITY UNIT RATE AMOUNT AMOUNT AS PER AMOUNT AS PER