CONSTRUCTION OF TOWN POLICE STATION (G+1) AT NALSAROVAR, Dist.-AHMEDABAD(INCLUDING ELECTRICAL WORK) (First attempt) (SBD)

Rate in Total Amount

Item No. Item Description Total Qty Unit Rate in Words

Providing and erecting Point wiring with 1.1 KV grade ISI marked 2 X 1.5 sq. mm copper PVC insulted FRLS

wire with 1.5 sq. mm (green) copper PVC insulated FRLS wire for earth continuity in FIA approved ISI mark

medium class white colour 20/25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive solution

erected on/in Brick Wall / slab along with continuous G.I. fish wire to draw wires and laid in approved manner

zari for PVC pipe and boxes shall be filled with cement mortar and finishing the surface to match the wall / ceiling

complete with approved make 5/6 Amp. ISI make modular type switch and accessories mounted in 20 G. G.I. RS: Four Hundred

company fabricated metallic box covered with appropriate front plate modules erected flushed with wall / ceiling Eighty One only

with necessary modular lamp holder / modular ceiling rose / HD Connector (make & model approved by EIC and

matching colur with switches accessories) (Deep Junction box 75mm depth if required) as directed for concealed

wiring. Light point. Cat.-III.

Necessary sheet / tape / polythene / sand must be erected or filled in all box to prevent mortar going into the

box. Length of point wiring must not increase than 10 mtr. For that necessary switch boards and their locations

must be finalised before execution by agency otherwise payment will not be done for extra long point. (For future

extention, if required, agency has to erect one higher size metal box and modular plate as per instruction of EIC.

Cost of blank plate shall be paid as per tender item) [This item include cleaning (inside/outside) of all G.I. switch

boards, electric point box, fan box, MCBDB & box cutting plaster finishing for modular plate without any gap]

[conductor resistance should be as per IS:8130/1984]

For Secondary Light Point, Cat.-III RS: One Hundred

For Bell Point, Cat.-III RS: Four Hundred

Eighty One only

For Fan Point.(with 6A Modular type switch and Two Module hum free 5/6 step EME step type Electronic fan RS: Six Hundred

243D regulator both having ISI Make ) Cat-III 175.00 Point 668.00

Sixty Eight only

For separate Point (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat. III RS: Five Hundred

For Looped on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) Cat. III

RS: Two Hundred

Fifty Five only

Providing and fixing Plug Point wiring with 1.1 KV grade ISI marked approved make 2 x 2.5 sq.mm copper PVC

insulated FRLS wire with 1.5 sq.mm (green) copper PVC insulated FRLS wire for earth continuity in FIA

approved ISI mark white colour medium class 20/25 mm dia. embossed rigid PVC pipe with PVC fitting fixed

with adhesive solution erected in wall/slab along with continuous G. I. fish wire to draw wires and laid in

approved manner zari for PVC pipe & boxes shall be filled with cement mortar & finishing the surface to match

the wall / ceiling complete with 16 Amp Modular type Swich and accessories mounted in 20 G. GI company RS: Seven Hundred

fabricated metallic box covered with appropriate front plate modules erected flushed with wall. (a) 16 Amp. Thirty Eight only

Indicator switch & 1 No. 6/16 A universal socket white colour suitable for 3/5 pin top duly both having ISI mark.

(Necessary sheet / tape / polythene / sand must be erected or filled in all box To Prevent Mortor Going In To The

Box) Cat.-III. (Conductor resistance should be as per IS:8130/1984)

Providing & Erecting Plug Point wiring with approved ISI marked 1.1 kv 2 x 4.0 sq.mm copper PVC insulated

FRLS wire with 2.5 sq.mm (green) copper PVC insulated FRLS wire for earth continuity in FIA approved ISI

mark white colour medium class 20/ 25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive

solution erected in wall/slab along with continuous G. I. fish wire to draw wires and laid in approved manner.zari

for PVC pipe & boxes shall be filled with cement mortar & finishing the surface to match the wall / ceiling

complete with 1 No 25 Amp Modular type Single pole MCB Swich and 1 no 25A universal 3 pin socket suitable

RS: Nine Hundred

245 for 3 pin top duty both having ISI mark .mounted in 20 G. GI company fabricated metallic box covered with 17.00 Point 991.00

appropriate front plate modules erected flushed with wall.Above accessories will be erected combined or

separately as per site requirement and instruction of EIC. (conductor resistence should be as per IS:8130/1984

Cat III (Gyser Point) (Necessary sheet / tape / polythene / sand must be erected or filled in all box to Prevent

Mortor Going In to The Box)

Providing & Erecting Plug Point wiring with approved ISI marked 1.1 kv grade 2 x 4.0 sq.mm copper PVC

insulated FRLS wire with 2.5 sq.mm (green) copper PVC insulated FRLS wire for earth continuity in FIA

approved ISI mark white colour medium class 25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with

adhesive solution erected in wall / slab along with continuous G.I. fish wire to draw wires and laid in approved

manner. zari for PVC pipe & boxes shall be filled with cement mortar & finishing the surface to match the wall /

ceiling complete with approved make 20 Amp. Modular type indicator switch and accessories mounted in 20 RS: Eight Hundred

246 SWG GI company fabricated metallic box covered with appropriate front plate modules erected flushed with wall 21.00 Point 863.00

Sixty Three only

/ ceiling. (a) 20 Amp Indicator switch & 1 No. 20 A universal socket white colour suitable for 3 pin top duly both

having ISI mark (A.C POINT ONLY) CAT III (Necessary sheet / tape / polythene / sand must be erected or filled

in all box to Prevent Mortor Going In to The Box)

Providing and erecting Medium Class FIA approved and ISI mark white colour (embossed) RIGID PVC PIPES

of following size complete erected with necessary PVC fittings & Junction boxes fixed with adhesive solution &

clamps on / in wall / ceiling along with continuous fish wire to draw mains with necessary fittings and junction RS: Twenty Four

boxes for following dia. For 20 mm. dia. only

For 25 mm. dia. RS: Thirty Three

Providing & Erecting Mains with FRLS PVC Insulated wire ISI marked 1.1 KV grade with FIA approved ISI mark

medium class 20/25/32 mm dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive solution to be

erected on/in brick wall / slab along with continuous G. I. fish wire to draw mains laid in approved manner with

plastering by cement mortar & finishing the surface to match the wall / ceiling complete with FRLS PVC insulated

wire for earth continuity. (Approved ISI make only) (Conductor resistance should be as per IS:8130/1984 ) [a] 2 x RS: Sixty Two

1.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper multi stranded only

conductor for earthing as per standard colour code. (with 20 mm dia. PVC pipe) [Wire must be having box

2 x 2.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper multi stranded

conductor for earthing as per standard colour code. (Conductor resistance should be as per IS:8130/1984) RS: Eighty Two

For 2 x 4.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 sq.mm. FRLS copper multi stranded

conductor for earthing as per standard colour code. (with 20/25 mm dia. PVC pipe) [Wire must be having box RS: One Hundred

packing] (Conductor resistance should be as per IS:8130/1984 ) Eleven only

For 2 x 6.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 sq.mm. FRLS copper multi stranded

conductor for earthing as per standard colour code. (with 25 mm dia. PVC pipe) [Wire must be having box RS: One Hundred

248D packing] (Conductor resistance should be as per IS:8130/1984 ) 230.00 Mtr. 146.00

For 4 x 10.0 sq.mm. FRLS copper multi stranded conductor mains with 4.00 sq.mm. FRLS copper multi

stranded conductor for earthing..As per standard colour code. (with 25/32 mm dia. PVC pipe) (Conductor RS: Four Hundred

resistance should be as per IS:8130/1984 ) Twenty One only

Providing & fixing 25 mm. dia Pvc insulated G.I corrugated flexible pipe with necessary socket, PVC bushes

RS: Thirty Seven

249 Saddle. 50.00 Mtr. 37.00

Providing & erecting Modular type accessories mounted on 20G. company Fabricated Galvanised Metal box

covered with appropriate front plate modules erected flushed with wall / ceiling with 1 Nos. TV Socket,1 Nos. of RS: Seven Hundred

16 Amp SP Switch & 3 Nos. of 6 Amp 3/5 pin plug. [For TV Switch board] Cat III Eighty Eight only

TV Co-axial Socket Outlet.Cat-III

RS: One Hundred

Fifty Nine only

For Two pin / RJ-11Telephone Socket (For One Gang) Cat III

RS: One Hundred

Fifty Nine only

For Blank plate single Cat-III

RS: Twenty Five

For Modem Jack for Computer Open RJ-45 Cat III

RS: One Hundred

Fifty Nine only

For Modular indicating call bell Cat.-III

RS: Three Hundred

Twenty Six only

For Modular Buzzer Cat.-III

RS: One Hundred

Forty Eight only

Providing & erecting Switch board for Computer or electric apparatus consisting of following items in single

board erected on Metal board with 3 mm thick PC (Polycarbonet) / Acrylic sheet erected as directed. 2 no. RS: One Thousand

251 6/16 Amp. universal Socket, 2 nos. 16 Amp. indicator switch, 2 nos. 6 Amp. Switch & 2 nos. 6 Amp. 5 pin Plug. 73.00 Each 1122.00 One Hundred Twenty Two

For Computer power Supply board. Cat.-III. only

Providing & erecting following size of TV Co-axial flexible cable comprising inner conductor of solid bare copper

insulated with Foam PE & Secondary conductor made of poly - Aluminium film bonded Al. Braids @ suitable

RS: Thirty Nine

252 coverage overall sheathed with black PVC insulation. for RG-6 [Polycab/ Finolex / RR Kabel Make] 300.00 Mtr. 39.00

Providing & Erecting 2.0 mtr long Earthing system by making minimum bore of 225 mm dia in soft soil. Suitable

for doing pipe-in-pipe technology earthing.Earthing electric rod must be made from Corrosion free Hot dip

galvanizing pipes having following specification.

(A) Earthing Electrode: outerpipe:- 88 mm minimum O.D., ISI 'B ' Class ISI mark of Reputed Brand, Inner pipe:-

42 mm minimum O.D., Pipe B Class ISI mark reputed Brand Terminal Size: 70mm X 100mm length, Terminal

Should be made from inner pipe for that pipe must be pressed and gave rectangular shape so its work as a

terminal.The hot deep galvanising must be done after above process.Galvanised thickness must be minimum

micron any where. SS Nut bolt:- 2 no.with washer suitable for 14mm dia. hole must be provided at terminal. total RS: Seven Thousand

minimum Weight(approx.) of earth electrodewith inside conductive material minimum should be 26 kg. Twenty Five only

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/meter testing as per IEC 62561-2017, Voltage drop:-

< 1 volt at no load & dry form, Sulphar content:- <2%

(C) Back fill Compound:- Earthing compound should be capable to retain moisture for long time Back Filling

Compound weight is 25 Kg.

(D) Chamber and cover:- Earthing chamber should be size of 400 mm X 400 mm X 400 mm depth and Cover

should be heavy duty cast iron with required size of 300 mm X 300 mm X 4 mm thick.

Necessary test report must be submitted.

1. Short circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

[Make and model approved by EIC Strictly subject to item specification only] [OEM has to submit all detail &

sample for approved before supplying]

[Water must be poured in bore before starting earthing. Earthing value must be measured with earth tester.

Agency has to bring the earth resistance to at least 02 ohms & voltage between neutral & Earthing upto 02 volt.

Agency has to maintain earthing & its value for one year. Earthing must be done in the presence of A.E.

For above earthing additional charges for boring in hard rock soil (by breaker) & filling soft soil in earth pit

(certificate for soil have to given by DEE / AE along with photographs) RS: Two Hundred

Seventy Six only

Providing & Erecting Mains with ISI marked, 1.1 KV grade electrolyte multi stranded, annealed copper conductor

with heat resistant PVC insulated conforms to IS:694, IEC - 227 erected in existing pipe of following size

(Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of RS: Twenty Seven

copper lugs, nuts and bolts if required. For One wire 2.50 sq. mm only

For One wire 6.00 sq. mm

254B 130.00 Mtr. 56.00 RS: Fifty Six only

For One wire 10.00 sq. mm

For one wire 16.00 sq. mm (For Solar system earthing & Panel Earthing)

RS: One Hundred

For one wire 35.00 sq. mm

RS: Two Hundred

Ninty Eight only

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/

Transformer LT panel board, Motors etc. using proper clamp with min 80 micron as per IS.Test certificate must RS: Seventy Seven

255 be submitted by agency. 50.00 KG 77.00

Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, LT panel board,

Motors etc. using copper clamp. RS: Seven Hundred

Eighty Seven only

Supplying & erecting M.S./ G.I metal Box having 16 Gauge painted with red oxide be concealed in wall with

necessary plastering & finishing covered with 3mm thick Laminated sheet with grooving as directed of following RS: Five and Paise

257 depth. 3" Depth 1000.00 Sq inch 5.94

Ninty Four only

Supplying and erecting 8W led lamps with following wattage capacity of 220 to 240 voltage, minimum

burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 RS: One Hundred

258 lamp holders, pf >= 0.5 LED Lamps integral type, with PC diffuser suitable LAMP holder 18.00 Each 111.00

Supplying and Erecting LED indoor fitting of approximately 4feet long with LED of wattage 0.2W to 0.5W

assemble on single MCPCB with housing use as a heat sink shall be made from Aluminum extrusion having

enough strength (sample must be approved by EIC) with polycarbonate diffuser with following specification: (A)

Company mark/name on the fitting.(B) Rated input voltage and frequency: 220V to 240 VAC ; 50Hz.(C) Rated

input wattage: max. 24w(D) Rated input current : 0.2 Amp

(E) Power Factor : Min. 0.90(F) ATHD : Max. 15%(G) Rated Luminous flux: Min. 2420 lm RS: Three Hundred

259 (H) CCT: 6500K(I) CRI: Min. 80Ra(J) Driver Efficiency: Min. 80%(K) LED life span: Min. 50000 Hrs @ L70(L) 15.00 Each 370.00

Over Voltage protection: Withstand up to 440V/AC for 4 Hrs.(M) Surge protection : Min. 2KV

(N) IP rating: IP 20(O) IK rating : IK 02(P) Short circuit , Open circuit & Reverse Polarity Protection must be

provided(Q) Fixing clamp design & strength should be sufficient to hold the fitting erected on wall or ceiling.(R)

core copper wire of appropriate size with earthing connector

(Note:-The manufacturer/ authorized Channel partner of the manufacturer has to submit 5 yrs free replacement

Guarantee for complete Fixture) [Approval will be given strictly subject to item specification]

SITC of Indoor Commercial recess/surface mounted (IP20) Max. 24 w Cool/warm white Color LED Down lighter

office Lighting Luminaire with external separate driver having BIS certification with fully die cast aluminium alloy

housing without any PVC/Plastic part with corrosion resistant powder coated finish as a heat sink with Poly

Carbonet diffuser LED complete (only from Philips Lumileds, CREE, BridgLux, Seoul, Nichia & Osram CRI >

RS: Seven Hundred

260 CCT 5600K (5400 to 5800K bin). The led's should be mounted onbacklit Metal core based PCB for better heat 405.00 Each 751.00

conduction and long life of LED. (LM 79 for complete fixture, LM80 for individual LED Report mustbe submitted)

The fixture should have extra protection of driver like over/under voltage, THD<15%, P.F.>0.90, for 24 w fixture

wide voltage range from 100 to 270 V, 50/60 HZ, 4 KV surge protection.

Fixure must have Min. 2160 Lumens light output. Fixture Efficacy should be>=90 Lumens/watt. (L70 @

Hrs) The Fixture should be able to easily mount on POP/Grid False cieling. The Luminiare should be tested as

per IP20 standards and following test reports should be submittedat the time of approval. Model Approved By

EIC as per Specification only (Note:- The manufacturer/authorized Channel partner/dealer of the manufacturer

has to give a 5 yrs. free replcement Guarantee for complete Fixture)

SITC of Indoor Commercial recess/surface mounted (IP20) Max. 18 w Cool/warm white Color LED Down lighter

office Lighting Luminaire with external separate driver having BIS certification with fully die cast aluminium alloy

housing without any PVC/Plastic part with corrosion resistant powder coated finish as a heat sink with Poly

Carbonet diffuser LED complete (only from Philips Lumileds, CREE, BridgLux, Seoul, Nichia & Osram CRI >

RS: Five Hundred

261 CCT 5600K (5400 to 5800K bin). The led's should be mounted on Metal core based PCB for better heat 150.00 Each 584.00

Eighty Four only

conduction and long life of LED. (LM 79 for complete fixture, LM80 for individual LED Report mustbe submitted)

The fixture should have extra protection of driver like over/under voltage, THD<15%, P.F.>0.90, for 18 w fixture

wide voltage range from 100 to 270 V, 50/60 HZ, 4 KV surge protection.

Fixure must have Min. 1620 Lumens light output. Fixture Efficacy should be>=90 Lumens/watt. (L70 @

Hrs) The Fixture should be able to easily mount on POP/Grid False cieling. The Luminiare should be tested as

per IP20 standards and following test reports should be submittedat the time of approval. Model Approved By

EIC as per Specification only (Note:- The manufacturer/authorized Channel partner/dealer of the manufacturer

has to give a 5 yrs. free replcement Guarantee for complete Fixture)

Providing and erecting max. 10 W LED battern having main housing aluminium extruded and front cover of

polycarbonate. Electrically and photomatry parameters are as under:240 V, 50 Hz. System wattage.:10W+10%,

PF>=0.95, system lumens min. 1000, CCT- 3000K to 6500K, CRI>=80, THD<=15%, Delivery efficiency>=85%,

LM 80 certified LED, 30000 Hrs@ L70, Electronic CC driver, insulated copper wire, for internal wiring, IP20

Operating voltage:160 to 270 V, Surge-2 KV, length of this fitting should be 2ft. RS: Three Hundred

262 Luminaire efficacy> 85 lumens/watt ,LED 13.00 Each 309.00

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) Tube Light

with integral driver 8 Watts, Surge-2 KV, IP-20, conventional 1 to 2 feet

Providing and erecting PVC body surface mounting LED Bulk head type 9 watt Lighting Fitting with electronic

driver having THD < 15%, CRI>80, P.F.0.95 And lumen output from luminaire 720 lm, input voltage range 160- RS: Seven Hundred

270 V AC, 50 Hz cool white (3000 to 6500 k), inbuilt driver having efficiency >=80lm/w, -20 deg C to + 60 deg C Eighty only

working temperature, AL frame with Beam Angle 120 deg.

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star rated, Ceiling fan with Brush

Less Direct Current (BLDC) permanent ferrite magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium

blades, 2 nos. canopies, shackle kit with earthing provision, copper winding, Power factor not < 0.9, Service

Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM,230v (tolerance as per IS : 374- RS: Two Thousand

264 2019), THD < 10%, compitible with electronic regulator unit for Speed Control and all remaining accessories 175.00 Each 2603.00 Six Hundred Three

including safety pin, nut bolts, washers, temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage only

and rectifier circuit with surge, over current and overload protection , 50 Hz, Single phase AC Supply, earthing

etc. Complete as required.[ Make shall be approved by Engineer in Charge] (A) 1200 mm Sweep (48")

Supplying & Erecting Fan Hook Of 10 mm M.S Round bar bounded to the RCC bars up to 50 mm Length each

side & piereced through 18 Gauge G.I Box having 125 mm dia depth of 75 mm complete erected concealed in RS: One Hundred

ceiling with necessary modular plate / sheet Twenty Five only

Supplying and erecting approved make oscillating type bracket fan A.C. 23OV. 50cy/s 400/450 mm sweep wall

RS: Two Thousand

mounted with height adjustment and rotary tilting device complete with guard, flexible Core plug top complete

266 7.00 Each 2509.00 Five Hundred Nine

erected with lead wires as directed. ( Make:- Baja,Usha, Crompton, Orient, Havells)

Supplying and erecting 19 / 20 mm. nominal bore "B" Class G.I Pipe /M.S. Pipe down rod erected duly painted

for fan complete with necessary 24/0.2 flat 3 core flexible cable with earthing.The Down rod RS: One Hundred

thickness,hole,locking arrangement,construction,power coating,colour shed should be same as original down rod Seven only

brought with ceiling fan.For that agency has to give original down road sample to fabricator and one sample

Supplying and erecting approved make 200mm sweep low noise decorative exhaust fan having

Aerodynamically designed and Blanced Blade, Blade finish Opaque,body colour White , finish Glossy , Rated

RS: One Thousand

Speed 1350/1800 revolution per minute ,air delivery 500m³ / hr , noise level 50 dB , Power Consumption

268 20.00 Each 1687.00 Six Hundred Eighty Seven

W, ,Rated Voltage 230 V , no. of blades 7 , guard 18 Louvers , square frame ABS body with inbuilt lowers

and square frame.( Havell s Make Ventilair LX or Bajaj, Usha, Crompton and Equivalent Model Approved by

EIC subject to Above Specification )

Providing and erecting Decorative Ding Dong call bell Stereo type 250 Volt complete erected on existing

polished wooden block or in M.S. box with 3 mm thick white ISI mark laminated sheet. (Anchor (chime), Vision, RS: One Hundred

Rider make) Seventy only

SITC of Vertical Air Termination Solid aluminium with Base - 10 mm dia. and 1000 mm long. Air Termination

Base tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350 µs RS: Nine Thousand

270 waveform in an accredited. Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol with MAST 34 3.00 Each 9323.00 Three Hundred Twenty

mm dia. 3000 mm long- Cold Galvanized as per EIC (Axis Electrical,OBO, JEF, CAPE, DHEN or equivalent Three only

make approved by EIC)

SITC of 8 mm dia solid Aluminium Conductor for roof top mesh grid and tested as per IEC 62561- 2 conducted

in the Govt. accredited thirty party laboratory to meet the requirement of IS/IEC 62305 with Required

Accessories - Aluminium Holding clamp at every 1 mtr distance, Aluminium/SS cross splicer at every crossing of

Alu. conductor, Expansion piece with connectors at every 20 mtr distance, Aluminium straight Splicer to connect RS: Two Hundred

271 conductors. All Accessories should be tested as per IEC 62561-1 2018 Cl. 6.3 for conditioning & Ageing Test & 300.00 Mtr 297.00

Ninty Seven only

6.4 for Lightning impulse current withstand test: 100 kA of 10/350µs waveform(Ageing & Electrical test )

conducted in a sequence manner & tested in the Govt. accredited Third party laboratory to meet the

requirements of IS/IEC 6230 (Axis Electrical,OBO, JEF, CAPE, DHEN or equivalent make approved by EIC)

SITC of Galvanized Steel Flat 25x6 mm thickness from earth electrode directly in ground as required. Zinc

coating: 500 g/m square (Approx:70 micron coating) tested and used exclusively for lightning protection earthing RS: One Hundred

system and ring equipotential bonding. [make and model approved by EIC strictly as per tender specification] Fifty Three only

SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel electrode with 250 micron copper bonding &

1 bag of Carbon fill Based environment friendly backfill tested as per IEC 62561-7 in NABL accredited RS: Five Thousand

273 Laboratory and suitable stainless Steel double sided clamp. Eco Friendly rust proof heavy duty weather proof 4.00 Per set 5933.00 Nine Hundred Thirty Three

Polyethylene Earth Pit Chamber with following dimensions: 254 mm dia (top), 330 mm dia (bottom) & 260 mm only

(height). [make and model approved by EIC strictly as per tender specification]

Providing & erecting weather proof, dust & vermin proof, floor mounted front operated indoor type cubical panel

board having IP-42 & above protection as per approval from engineer incharge and made from 2 mm. thick CRC

M.S. sheet for outer body & doors, 1.6 mm. thick CRC M.S. sheet for internal partitions with necessary

supporting angles, flats including skirting, bending, drilling, welding, riveting with internal partitions & cable alley

as per requirements & instruction of engineer-In-Charge with erection of supplied switchgears, busbars with

suitable size of interconnecting PVC copper wire / Copper-Aluminium strips, rubber gromets, rib, control wires,

backelite control fuses, measuring instruments, earth bus & earth bolts, foundation flange-bolts-base plates, RS: Sixteen Thousand

274 sufficient nos. of hinged doors, handle with locking arrangement, rubber gasket complete with Required Nos. 4.00 Sq. Mtr. 16230.00 Two Hundred Thirty

heavy Duty Connector with Cadmium plated nut and bolt for Anti rusting. The panel shall be supplied with Seven only

Tank chemical process which shall be carried out before applying painting, painted with powder coating. (The

rates excludes the cost of switchgears, busbars, interconnecting mains & Copper / Aluminium strip, fuse, meters

etc. The dimension shall be measured excluding base beams) The standard companies switch gear shall be

used and only manufacturers at CPRI approved factory as per IEC 61439 and shall be certified by that company

whose switch gears are used after fabrication for beneficial use. With 350 mm depth

Panel manufacturer have to give 5 years maintenance and service support if in case of breakdown or fault.

Panel manufacturer have to submit electrical meter calibration report. Agency should design the panel in such a

way that there should not be any excess in panel area (sq.mtr) & length of bus-bar (mtr), if any excess occurs

draw attention to GSPHCL at the time of approval of G.A. drawing.

Loading and unloading of above item shall be done by hydra and skill work force under supervision of electrical

engineer and guidelines given by manufacturer to avoid damage to the item. Picture of it to be submitted in

running bill / final bill.

Size of door and Ele. room / Pump room shall be checked by agency's engineer before giving order. If found any

problem in size discuss with GSPHCL engineer for rectification before giving order. [Including Necessary

numbering / marking on PANEL done with red colour radium sticker as per site requirement and instructions

given by EIC on site. Font / number size given by EIC on site as per requirement] (All Panel as per IEC

as per NBC Guideline) [Manufacturer must be of Gujarat state so three stage inspection can be done]

Supplying and erecting tripple pole & neutral 440V / 500 V Panel mounting Copper Busbars with four equal Nos.

of electrolyte bus having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area)

RS: One Thousand

duly wraped with colour insulating tape for phase sequence of following current carrying capacity, erected with

275a 1.00 Rmt 1942.00 Nine Hundred Forty Two

necessary bus bar supports / insulators, main cable socket to each bar, erected in existing cubical panel with

necessary connections.For electrolyte copper busbars Suitable for 100 Amp. capacity.

For Suitable for 200 Amp. Capacity

RS: Three Thousand

275b 1.00 Rmt 3171.00 One Hundred Seventy

For Suitable for 300 Amp. Capacity

RS: Four Thousand

275c 1.00 Rmt 4861.00 Eight Hundred Sixty One

Supplying & erecting approved make Four Pole 415 V change over switch interior for panel mounting with

operating mechanism A.C.23 duty confirming to IS [a] For 250Amp FP . Cat III

276a 1.00 Each 13221.00 Thousand Two Hundred

Twenty One only

For (C)100-125A FP C/O Switch . Cat III

RS: Seven Thousand

276b 2.00 Each 7713.00 Seven Hundred Thirteen

For 63A FP C/O Switch

RS: Four Thousand

276c 1.00 Each 4738.00 Seven Hundred Thirty

Supplying and Erecting Approved make Four pole moulded case circuit breaker having breaking capacity ICU of

35 K.A. at 415 V. having normal current rating 250 A. with Variable or fixed thermal & magnetic release suitable RS: Twenty Thousand

277 to work on A.C.supply 50 c/s. with all internal connections spreader tinned copper & complete erected in existing 2.00 Each 20739.00 Seven Hundred Thirty

16 G.M.S. housing. housing. ICS=100% of ICU only Nine only

Providing and Erecting approved make Four pole moulded case circuit breaker having breaking capacity ICU of

25 KA. at 415 V. having normal current rating 25 A to 100A. with variable or Fixed thermal & magnetic release RS: Six Thousand

278 suitable to work on A.C.supply 50 c/s. with all internal connections,spreader tinned copper & complete erected in 4.00 Each 6112.00 One Hundred Twelve

existing 16 G.M.S. housing. ICS=100% of ICu only. ( only

Providing and Erecting approved make Four pole moulded case circuit breaker having breaking capacity ICU of

35 KA. at 415 V. having normal current rating 125A. with variable or Fixed thermal & magnetic release suitable RS: Seven Thousand

279 to work on A.C.supply 50 c/s. with all internal connections,spreader tinned copper & complete erected in existing 3.00 Each 7976.00 Nine Hundred Seventy Six

16 G.M.S. housing. ICS=100% of ICu only. only

Providing and erecting following additional parts for panel mounting MCCBs (A)Extended operating rotary handle

with pad lock with three position trip,off,on suitable for 25A to 250 A panel mounting. Company must be same as RS: Eight Hundred

280 Switchgear company. 11.00 Each 865.00

Sixty Five only

Approved make Earth fault Relay suitable to mount with inter connection to moulded case circuit breaker having

CT ratio & MCCB rating as following along with shunt trip 220V AC. with all internal connections & complete RS: Five Thousand

281 erected in existing M.S.housing. For 250A- 400A, CT Ration 1/400 (For Sub Panel, Main Panel) 3.00 Each 5362.00 Three Hundred Sixty Two

Supplying and erecting approved make panel mounting type Digital Voltmeter having 3 x 1/2 digits LED display,

0.5 class of accuracy 0 to 750 AC Volts range erected on existing panel board with all connection, wiring etc. RS: One Thousand

282 with manufacturers calibration certificate. 3.00 Each 1263.00 Two Hundred Sixty Three

Supplying & erecting aproved make Panel mounting type Digital Ammeter having Three Digits LED Display,0.5

RS: One Thousand

class of accuracy, External CT operated Calibrated for 0 to 1000 Amps suitable to operate on 500 Volt AC

283 3.00 Each 1543.00 Five Hundred Forty Three

erected on existing panel board with all connection wiring etc.with manufacturers calibration certificate.

Supplying, erecting, testing and commissioning of Ammeter / Voltmeter selector switch for 3 phase AC supply

500 V on existing panel board with necessary connections. RS: Three Hundred

Supplying and erecting approved make set of indicator lamps LED lamp, lense cover, bakelite holder complete

erected with necessary connections. RS: Forty Three

Providing, erecting, testing and commissioning of L.T. Current Transformer with bus bar primary 50/5 to 1000/5

ratio 15 VA burden having 0.5 Class Accuracy Duly secured with insulating materials connected to the meter. RS: Two Hundred

Seventy Two only

Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark ( RS: One Hundred

For 3 phase DB 24nos. , 6 nos. Main Panel and sub panel) Eleven only

Providing and erecting 240 volt MCB double pole switch for M&I(C Curve) having 10 KA Breaking capacity and

confirms to IS : 8828 in existing with earthing terminal having following capacity. For 6-32 Amp Capacity. RS: Two Hundred

Ninty Seven only

Providing and erecting 240 volt MCB double pole switch for M&I(C Curve) having 10 KA Breaking capacity and

confirms to IS : 8828 in existing with earthing terminal having following capacity. For 40 Amp Capacity. RS: Three Hundred

Twenty Seven only

Providing and erecting 415 Volt MCB four pole motor & inductive load(c Curve) having 10 KA Breaking capacity

and confirms to IS : 8828 in existing metal box having following capacity. For 40 Amp FP. RS: Six Hundred

Providing and erecting 415 Volt MCB four pole motor & inductive load(c Curve) having 10 KA Breaking capacity

and confirms to IS : 8828 in existing metal box having following capacity. for 63 Amp FP. RS: Seven Hundred

Providing and erecting 240 volt MCB double pole switch for M&I(C Curve) having 10 KA Breaking capacity and

confirms to IS : 8828 with same company Metal box with earthing terminal having following capacity. with RS: Five Hundred

necessary quarter Numbering with oil paint by Painter. for 40 Amp Capacity. Two only

Providing and erecting 240 volt MCB Four pole switch for M&I(C Curve) having 10 KA Breaking capacity and

confirms to IS : 8828 with same company Metal box with earthing terminal having following capacity. with RS: Nine Hundred

necessary quarter Numbering with oil paint by Painter. For 63 Amp Capacity. Five only

Supplying & fixing box for housing RCCB + MCB combination made of 18 SWG sheet steel duly powder coated

with gasket, dust & vermin proof bakelite shield two earthing terminals for following type of RCCB, RCCB + MCB

with necessary numbering / marking with oil Paint by painter. [a] For 2 pole [Box must be of same company as RS: Two Hundred

MCB, ELCB used] Seventy Two only

For 4 pole [Box must be of same company as MCB, ELCB used]

RS: Four Hundred

Providing and Erecting approved make ELCBs / RCCBs conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 6 KA and suitable for operation on single phase 240 V. having RS: Two Thousand

295 characteristic of quick action & tripping with all advance feature & do not incorporate any electronic component. 2.00 Each 2213.00 Two Hundred Thirteen

for following Max. rating erected as directed for 40 Amps.DP only

Providing and erecting metalic danger notice board as per language suggested by engineer inchrge for MEDIUM

VOLTAGE installation to be erected as per IS-2551 RS: Sixty Nine

Supplying & erecting bank of all polypropylene condenser (APP type) with standard capacity of 2,3,5,7,

& 15 KVAR units of P.F. correction for operation on 3 phase 50 c/s, 400 /440V (+ / - 10%) with externally

discharging resistance, earthing terminal & built on angle iron of channel iron frame work and provided with

terminal cover box. Complete erected on provided iron bracket or on floor duly tested by license. RS: Six Hundred

Providing ad erecting approved make single phase Double Door metal clad D.B. as per relevant indian

standards ammended upto date.

Supplying and fixing following way single phase MCB distrubution board of company fabricated with sheet box

with powder coated inside and outside after apply seven tank chemical process of MS sheet cover complete with

suitable integral single piece construction tinned copper busbar and link with all necessary interconnection and

with necessary size MS frame for mounting MCBDB. Manufacturer must be provided (1) IP 43 and as per

IS:8623-1 & 3, IEC 61439-1 & 3 having D type PU gasket. (2) Seven tank Powder coating Certificate (3) Tinned

Copper/Brass make neutral & Earthing link with isolation & Protecting Cover for 240 Volts on surface / recess

complete with loose wire box, terminal connectors for all incoming and outgoing circuits, with suitable size FRLS RS: Five Thousand

298 PVC insulated copper conductor up to terminal blocks and internal connection, tinned coppper bus bar, 1 no. 14.00 Each 5868.00 Eight Hundred Sixty Eight

tinned copper neutral link, tinned copper earth bar, din bar, detachable gland plate, interconnections, powder only

painted including earthing etc.

Single phase incoming and horizontal single phase outgoing. For 16 Way MCBDB: Including 40 Amp. 30 mA

double pole ELCB (ELCB confirming to IS:12640/1988 having sensitivity of 30 mA and breaking capacity of

KA), MCB 40 Amp. double pole switch (C curve confirms to IS:8828 having breaking capacity of 10 KA) and S.P.

MCB of rating 6 to 32 Amp. with NL suitable to operate on 240 Volt A.C. power. (6 Amp:- 4 Nos., 16 Amp:-

Nos. & 25 Amp: 4 Nos.) Cat.-III

(The DBs should be used of same company of MCB / ELCB to be used) (MCBDB must be erected in line & level

with spirit level and finish the external edge with box cutting plaster) (Same colour MCB(SP/DP) should be used

as same as MCBDB) [Including Necessary numbering / marking on box done with red colour radium sticker as

per site requirement and instructions given by EIC on site. Font / number size given by EIC on site as per

Supply, Installation, Testing & Commissioning of Three Phase, 440 V Surge Suppressor protection Device (SPD)

& 40 Amp TPN MCB (or As per SPD OEM guide line for the protection of SPD which is erected such a way that

it can be operated easily) SPD must be capable to protect all electrical and electronics equipments if SPD blast

RS: Six Thousand

or fuse then the panel builder must have replace it soon during defect liability period.The Detail Specification of

299 3.00 Each 6319.00 Three Hundred Ninteen

SPD are As per Attached sheet with Annexture -A(E). (Hakel,ikra,OBBO make) (With Three year

Gaurantee/warranty)

Supplying and erecting Servo Controlled Voltage Stabilizer (SCVS) as per following requirement: (1) Input

Voltage Range - Three Phase 340 To 480 Volt AC. (2) Out put Volatge - Three Phase 415 Volt AC (Line - Line)

with Voltage Regulation of +/- 1%. (3) Frequency range - 47 Hz To 63 Hz. (4) Efficiency - More or equal to 98%.

(5) Type of Stabilizer - Suitable for Balance & Unbalance Load and Voltage including SPD (6) Controlled Type -

Digital Micro Controller Based Disply. (7) Rate Of Correction - Upto 100 Volt / Sec (Line - Line) (8) Servo Motor

Drive - AC Syncronous Stepper Motor - As per KVA Capacityy, Out put volatge and Voltage regulation

requirement. (9) Nil Wave form Distortion and Effect of Load POwer. (10) Responce Time - 10 milli second. (11)

Protection requirements - Input low Cut off protection / Input High Cut Off Protection / Output Low Cut Off

protection / IOutput High (12) Fault Annuciation Panel LED shows Input present, Input high Input low, Output RS: Two lac Nine

300 Normal, Output High, Outpur low, Overload. (13) Output On time delay - 10 seconds (14) Ambient Tempeature 1.00 Each 209875.00 Thousand Eight Hundred

capacity - 0 - 45 RH upto 90 %. (15) Enclosure Type - IP 20 (16) Type of Cooling - Air ,Output:Bypass switch Seventy Five only

with changeover switch and Provied SPD & 4 year free replacement guarantee on Stamp paper.

Loading and unloading of above item shall be done by hydra and skill work force under supervision of electrical

engineer and guidelines given by manufacturer to avoid damage to the item. Picture of it to be submitted in

running bill / final bill.Size of door and Ele. room / Pump room shall be checked by agency's engineer before

giving order. If found any problem in size discuss with GSPHCL engineer for rectification before giving order. (75

KVA) (Fuji Electric, Servomax Limited, Krykard, protekG Make)

Supplying and erecting Servo Controlled Voltage Stabilizer (SCVS) as per following requirement: (1) Input

Voltage Range - Three Phase 340 To 480 Volt AC. (2) Out put Volatge - Three Phase 415 Volt AC (Line - Line)

with Voltage Regulation of +/- 1%. (3) Frequency range - 47 Hz To 63 Hz. (4) Efficiency - More or equal to 98%.

(5) Type of Stabilizer - Suitable for Balance & Unbalance Load and Voltage including SPD (6) Controlled Type -

Digital Micro Controller Based Disply. (7) Rate Of Correction - Upto 100 Volt / Sec (Line - Line) (8) Servo Motor

Drive - AC Syncronous Stepper Motor - As per KVA Capacityy, Out put volatge and Voltage regulation

requirement. (9) Nil Wave form Distortion and Effect of Load POwer. (10) Responce Time - 10 milli second. (11)

Protection requirements - Input low Cut off protection / Input High Cut Off Protection / Output Low Cut Off

protection / IOutput High (12) Fault Annuciation Panel LED shows Input present, Input high Input low, Output RS: Seventy

301 Normal, Output High, Outpur low, Overload. (13) Output On time delay - 10 seconds (14) Ambient Tempeature 1.00 Each 70438.00 Thousand Four Hundred

capacity - 0 - 45 RH upto 90 %. (15) Enclosure Type - IP 20 (16) Type of Cooling - Air ,Output:Bypass switch Thirty Eight only

with changeover switch and Provied SPD & 4 year free replacement guarantee on Stamp paper.

Loading and unloading of above item shall be done by hydra and skill work force under supervision of electrical

engineer and guidelines given by manufacturer to avoid damage to the item. Picture of it to be submitted in

running bill / final bill.Size of door and Ele. room / Pump room shall be checked by agency's engineer before

giving order. If found any problem in size discuss with GSPHCL engineer for rectification before giving order. (20

KVA) (Fuji Electric, Servomax Limited, Krykard, protekG Make)

Supplying and laying UPVC cable trunking system comprising unplasticised polyvinyl, chloride rigid material with

ignition free & flame proof confirming BS with necessary end caps Internal and external bend, flat bends,

RS: Two Hundred

302a coupler, tee etc. All necessary accessories and measuring of following sizes.For 75 mm x 50 mm trunking (MK / 20.00 Mtr. 275.00

Seventy Five only

Legrand/OBO Make Only)

100 mm x 50 mm trunking (MK / Legrand/OBO Make Only) RS: Four Hundred

Twenty Four only

Providing, erecting, fabricating the M.S. structure as per requirement of site as per structure design Including

proper size approved by EIC of M.S. angles, flats, bars, square pipe, channels, sections (Tata,Zindal,Asian,Jsi

Make) complete with cutting, welding, grinding and finishing duly painted with Asian/Nerolac make premium

quality oil paint and true care red oxide metal primer,asian paint make with erection on site as per direction of RS: Seventy Four

engineer in charge with necessary grouting cementing, plastering and finishing complete. All hole opening of and Paise Ninty Two only

square pipe end must be closed with M.S plate welding. Payment will be done on KG as per Actual weight.

Supplying & erecting 12 mm thick backelite sheet of approved make and grade on 25 x 25 x 3 mm red oxide

painted angle iron frame suitable for fixing ICDP SWITCH and energy meter (contractor shall make approved RS: Two Thousand

304 drawing of Bakelite sheet To arrange required No. of Energy meter & ICDP switch -busbar etc. as per Actual 2.00 Sq. Mtr. 2289.00 Two Hundred Eighty Nine

space available in electrical room at site) only

SITC of specified make X color for Cat.-6 Data and Y color for Cat.-6 voice cable to be done in prelaid PVC pipe

/ raceway, but without the cost of raceway or pipe (the wire is to be drawn from MFD/ JB to outlet point) (a) CAT RS: Forty Seven

305 - 6 (For Computer Cabling and For Voice Cabeling) (Molex, Avaya, D-Link, Legrand make Only) 700.00 Mtr. 47.00

SITC of 24 x 10/100/1000BASE-T ports

4 x Gigabit RJ45/SFP Combo ports

Advanced L2 switching and security features

L2+ Static Routing RS: Fifteen Thousand

306 Optional “standard mode” or “surveillance mode” management user interface 3.00 Each 15247.00 Two Hundred Forty Seven

[Approved by Competent only

Authority i.e. not Below the rank of Executive Engineer ]

Supply, Installation, testing and commissioning of 24 port Cat 6 19" Toolless Patch Panel ( fully loaded) enable

all possible combinations of the various types of cable mounted on the same panel by using various toolless

connector blocks/modules. Have a metal structure enabling them to be durably fixed to the uprights of the 19”

chassis and assuring automatic grounding between toolless RJ-45 connectors, the panel, and the 19” uprights of

the enclosure. Include rear cable support with plastic cable guides to hold cable without need for cable ties. RS: Four Thousand

307 Include quick mounting system to mount the panel into the 19” rails without use of cage-nuts. These may be 3.00 Each 4357.00 Three Hundred Fifty

used to secure the connections of wifi access points, IP cameras, servers, or other critical devices. Front Seven only

Removal IO's option for maintenance and trouble shooting with 6 Different Colours Labels for Labelling &

Identification of Individual Ports. & as per attached details specification. (CAT 6 )

SITC of company fabricated Patch cords shall conform to Cat- 6 & conductor shall be stranded for better

flexibility Shall support network line speeds up to 1 Gbps Shall have RJ-45 jacks. For 1 Mtr.[Make and model RS: One Hundred

approved by EIC as per specification] Fifty Five only

SITC of company fabricated Patch cords shall conform to Cat- 6 & conductor shall be stranded for better

flexibility Shall support network line speeds up to 1 Gbps Shall have RJ-45 jacks. For 2 Mtr. [Make and model RS: One Hundred

approved by EIC as per specification] Ninty Nine only

Supply and installation of 9U steel rack for installing 4 nos. Ethernate switches/Hubs. The Rack should be fully

enclosed steel housing fabricated with 14 SWG sheet and powder coated with glass doors and having wire

RS: Eleven Thousand

management systems. The rate includes the Exhaust Fan, 2 nos. 4 socket and 1 switch power strip and all the

310 3.00 Each 11441.00 Four Hundred Forty One

wiring in the rack. (Rittal, Valrack, APC, Legrand Make and model approved by EIC as per specification)

Supplying & erecting Delton or approved make Telephone Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer Jacket suitable

for telephone wiring & confirming to C-DOT erected in existing pipe. of following size of conductors & nos.of RS: Four Hundred

311a pairs. With necessary connections. For Conductor Size 0.5 mm armoured Fifty Pairs.[make and model approved 150.00 Mtr 463.00

Sixty Three only

by EIC strictly as per tender specification]

For Conductor Size 0.5 mm armoured Twenty Pairs.[make and model approved by EIC strictly as per tender

RS: One Hundred

311b specification] 100.00 Mtr 198.00

Ninty Eight only

Providing & erecting main Distribution (MDF) indoor type, back mounted frame as per DoT standard approved RS: One Thousand

312a with krone strips For Suitable For Suitable for 20 pair 2.00 Each 1355.00 Three Hundred Fifty Five

For Suitable for 50 pair RS: One Thousand

312b 2.00 Each 1730.00 Seven Hundred Thirty

Supply, Installation testing and commissioning of 16 Gauge M.S. Powder coated floor raceway Access outlet

/ service junction box with 16 Gauge M.S. Powder coated Cover plate with duct entry 25 mm / 38 mm size

having epoxy powder coated trap lead with corrosion & rust free with adjustable levelling screw of following size.

for 300 mm x 300 mm x 50 mm depth. (M.k, legrand, OBBO) RS: Seven Hundred

Forty Nine only

150 mm x 150 mm x 50 mm depth (M.k, legrand, OBBO) RS: Six Hundred

Seventy Two only

Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box with Hot Deep Galvanised door having 2 nos. 180° operated hinges & 2 nos. Ln

key locking with silicon rubber gasket. Consist of terminal plate of min 6mm Hylam sheet, standard profile

mm X 7.5 mm Din-Rail & MCB, Brass stud type terminal and arrangement for cable termination to be erected on

RS: Six Thousand

RCC foundation as per details given by manufacturer and EIC considering site requirement. Foundation Details:

314 14.00 Each 6917.00 Nine Hundred Seventeen

(1) Grade of RCC 1:2:4, (2) Grade of steel rainforcement of RCC FE 415, (3) Clear cover to rainforcement

50mm, (4) Concrete vibrated, (5) use suttering / farma, (6) Hot deep galvanized average 70 Micron, (7) Detail

drawing will be given by corporation

For 5 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm thickness with 200 mm X 200 mm X 12 mm base

plate, 4-M16 Bolts and 600 mm long hot deep galvanized J-Bolt, nuts, washers with 800 mm under ground and

200 mm above ground level and Foundation in 1:2:4 proportion as per details given by manufacturer and EIC

considering site requirement. Approx Pole weight 46 kg.(Make:- Bajaj, Valmont, Transrail, Ambica Only) (Test

certificate to be submitted)

Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out approx. 2mm thick

box complete with Bakelite connector strip 5way(3P+N+E), DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts, bolts & washers suitable for erection RS: Eight Hundred

315a on pole with cable clamps& earth bolt of following size of box. For 300mm x 200mm x 100mm 16.00 Each 890.00

For 250mm x 200mm x 100mm [deep]

RS: Five Hundred

For 140mm x 140mm x 100mm [deep]

RS: Two Hundred

Ninty Five only

Supplying and making Coil type earthing, coil made from 8 SWG galvanised iron wire with 50 mm OD and

turns (length of turns approx. 200 mm) and having additional continuous streight length of 3.00 mtr at open end

and should be connected to earthing bolt and burried in 1.5 mtr deep specially prepared earth pit complete with

salt and charcoal/coke as required for coil type earthing.(Approx weight of coil 1.0 to 1.1 Kgs) RS: Three Hundred

Sixty Nine only

Supplying and erecting Fabricating terminal box for street light pole made from 16 SWG M.S. sheet having

following size complete with fixing arrangement for terminal board, with necessary hole for wire entry and exit

from the box. The box shall be provided with cover and hinges on one side and bolting at other end The box

shall be fixed by clamps fabricated from 25mm x 6mm flat.The box shall be painted with one coat of red oxide

and two coats of paint having following box size 330 mm x 260 mm x 140 mm (depth). Providing and fixing RS: Seven Hundred

Terminal board of size 5.0 x 127 x 152.4 mm.bakelite sheet with 15 Amp. kitkat pattern porcelain fuse unit with Two only

suitable brass studs with nuts, washers and clamps of size 25 mm x 3 mm suitable for pole painted with one

coat of red lead paint.

Providing & erecting bracket consisting of ISI mark "B" class G.I. Pipe 4.2 cm outside diameter complete with

suitable G.I. Sleeve tubing of 2 mm. thick and required size and length suitable for 76.5 / 80 mm. required size of

pole top or pipe in pipe surface for terrace as per instruction of EIC or wall bracket as per instruction of EIC

having nuts and bolts for fixing the brackets and having spread of Upto 0.50 mtr. length with suitable rise as per

site condition and suitable welded stiffner reducer and nipple with check nut complete painted with one coat of RS: Four Hundred

318a yellow zinc and two coats of alluminium paint for Single arm bracket suitable for pole or terrace as per design 22.00 Each 487.00

Eighty Seven only

given by EIC. For single arm bracket. (Jindal / Asian / Tata / Surya Prakash make Only) (Fabricators:- Bajaj,

Valmont, Transrail, Ambica, RR Ispat Only) (Test certificate to be submitted)

For Double arm bracket. (Jindal / Asian / Tata / Surya Prakash make Only) (Fabricators:- Bajaj, Valmont,

Transrail, Ambica, RR Ispat Only) (Test certificate to be submitted) RS: Six Hundred

SITC of Outdoor aesthetically designed LED Street Light Luminaire with total consumption of Max. 45 W with

single piece die cast aluminium housing, high power LED shall be mounted on high quality metal core PCB with

extremely precison designed heat sink complete with IP66 protection Class with polycarbonate / thoughened

glass cover the fixture should be suitable for pole/bracket mounting. The fixture to comply both LM79 and LM

guidelines with LED module min. 130 lumen/watt with toughen Glass L70 at 50,000 hrs, provided with high

quality polycarbonate lenses for better light distribution. The watt capacity of Each LED must be >=4W in street

light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted, provided with high quality RS: Three Thousand

319 driver for protection against high and low Voltage cut Off, opertional for high amibient and high humid 18.00 Each 3512.00 Five Hundred Twelve

envirnoments, THD of driver should be less than 10% and P.F > 0.95. Also the Fixture should meet the following only

technical criterias Oprating range Voltage 160 to 270 V, system efficiency >= 110 lm/w, and total lumens not less

then 4950, CCT > 5000K, CRI > 65, beam angle 120 deg, surge immunity level at least 4 KV integral and 10 KV

non integral (Note:- The manufacturer / authorized Channel partner of the manufacturer has to submit 5yrs free

replcement Guarantee for complete Fixture)

SITC of Outdoor aesthetically designed LED Street Light Luminaire with total consumption of Max. 90W with

single piece die cast aluminium housing, high power LED shall be mounted on high quality metal core PCB with

extremely precison designed heat sink complete with IP66 protection Class with polycarbonate / thoughened

glass cover the fixture should be suitable for pole/bracket mounting. The fixture to comply both LM79 and LM

guidelines with LED module min. 130 lumen/watt with toughen Glass L70 at 50,000 hrs, provided with high

quality polycarbonate lenses for better light distribution. The watt capacity of Each LED must be >=4W in street

light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted, provided with high quality RS: Six Thousand

320 driver for protection against high and low Voltage cut Off, opertional for high amibient and high humid 16.00 Each 6117.00 One Hundred Seventeen

envirnoments, THD of driver should be less than 10% and P.F > 0.95. Also the Fixture should meet the following only

technical criterias Oprating range Voltage 160 to 270 V, system efficiency >= 110 lm/w, and total lumens not less

then 9900, CCT > 5000K, CRI > 65, beam angle 120 deg, surge immunity level at least 4 KV integral and 10 KV

non integral (Note:- The manufacturer / authorized Channel partner of the manufacturer has to submit 5yrs free

replcement Guarantee for complete Fixture)

SITC of Outdoor aesthetically designed LED Flood Light Luminaire with total consumption of maximum 120 W

with single piece die cast aluminium housing, high power LED shall be mounted on high quality metal core

based PCB with extremely precison designed heat sink, complete with IP66 protection Class, with polycarbonate

/ Toughened glass cover. The fixture should be suitable for pole/bracket mounting. The fixture to comply both

LM79 and LM 80 guidelines with LED minimum 130 lumen/watt with L70 at 50,000 hrs, provided with high

quality polycarbonate lenses for better light distribution. The Fixture Should be able to be Pole Mounted and also

bracket mounted, provided with high quality potted driver for protection against, high and low Voltage cut Off, RS: Seven Thousand

321 opertional for high amibient and high humid envirnoments, THD of driver should be less than 10% and P.F > 2.00 Each 7395.00 Three Hundred Ninty Five

0.95. Also the Fixture should meet the following technical criterias. Operating range Voltage 160 to 270 V, only

system efficiency >= 110 lm/w, CCT > 5000K, CRI >65, beam angle 120 deg, surge immunity level at least 4KV

integral & 10 KV nonintegral. Flood Light lumens shall be not less than 13200 (Note:- The manufacturer /

authorized Channel partner of the manufacturer has to submit 5 yrs free replcement Guarantee for complete

SITC of Outdoor aesthetically designed LED Flood Light Luminaire with total consumption of maximum 90 W

with single piece die cast aluminium housing, LED's mounted on high quality metal core based PCB with

extremely precison designed heat sink, complete with IP66 protection Class, with polycarbonate / Toughened

glass cover. The fixture should be suitable for pole/bracket mounting. The fixture to comply both LM79 and LM

80 guidelines with LED minimum 110 lumen/watt with L70 at 50,000 hrs, provided with high quality

polycarbonate Seperate lenses for better light distribution. The watt capacity of Each LED must be >=4W in

street light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted, provided with high RS: Six Thousand

322 quality potted driver for protection against, high and low Voltage cut Off, opertional for high amibient and high 2.00 Each 6228.00 Two Hundred Twenty

humid envirnoments, THD of driver should be less than 10% and P.F > 0.95. Also the Fixture should meet the Eight only

following technical criterias. Operating range Voltage 160 to 270 V, system efficiency > 110 lm/w, CCT > 5000K,

CRI >65, beam angle 120 deg, 4kV integral & non integral surge immunity level at least 10 KV non integral...

Flood Light lumens shall be more than 9900. (Note:- The manufacturer / authorized Channel partner of the

manufacturer has to submit 5yrs free replcement Guarantee for complete Fixture)

supplying & erecting 30 W LED POST TOP LATTERN fitting with high power white LEDs wattage of 1 ww and

above assebled on single MCPCB's effiency more than 130 lumens per watt and corrosion free high pressure

diecast alluminium housing with smooth finish powder caoted and heat sink extruded alluminium with difuser and

poly carbonate optics/ lences with compny mark / name /engraved or embossed 120 to 300 volt, power factor

more than 0.95, THD < 10%, CCT 5000K to 5700K , Uniformity ratio > 0.45, Luminure efficency Min 110 lumens

per watt. LED Driver efficency > 85%. Cree/osram/philips Lumileds/Nichia /Seoul/Bridge Lux (USA) make LED RS: Four Thousand

used for luminare ( Each Fitting required LM 79 and LM-80 certificates) (B) Flood Light(IP-65)Surge- Fifty Two only

10KV.(E)Post Top Latern LED Fitting Comprises of 650 MM TOP diameter 120 degree beam angle with 3 Nos

supporting ribs proposed for garden & Promenade. maximum 40 WATT, (Note:- The manufacturer/authorized

Channel partner of the manufacturer has to submit 5yrs free replcement Guarantee for complete Fixture)

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. & corrosion resistance with diffuser

housed in aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

RS: Eight Hundred

324 Luminaire efficacy> 85 lumens/watt , 100 Each 805.00

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)(F) Spot

Light 5 Watt 425 Lumens, Surge-2KV ( For Police Station Outside elivation Light)

Providing , erecting , testing and commissioning Insu Intelligent Streetlight Controller specially design for energy

saving in conventional streetlight system ( Cat. No. SLC-03-1Ph-7.5KVA-20Amp/Cat NoSLC-03-1 ph-15 KVA

amp per phase) having technial specification ,1 phase 2 wire, 230 V AC/ph +/- 25% R Y B N 2 Wire supply

System.50 Hz (+ / - 10 %), 2 W (Stand By) to 4 W (at street light operation)consuption, Advance 8 bit micro

controller, switching on longitude and latitude base, accaracy of +- 1 minute per month. with inbuilt battery, with

battery life of more than 8 years, with speicial device which hold the parameter for more then 10 years without

any power and password protected. 16 character and two line LCD display with backlight, 4 keys user friendly

RS: Twenty Thousand

keyboard system, 7500 VA feeder pillar capacity, 63/100 amps isolator ,3 Outpus with termination 40/63 Amps

325 1.00 Each 20255.00 Two Hundred Fifty Five

2/3 pole contactor , 3X16 Amps with F R cable provision to by pass by way of relay operation through

auto/manual switch, 2 to 55 centigrade and humidity 90 % non condensing Outdoor type installation on pole with

clamps.(Provided with clamps and nut bolt) or wall or floor, three locking system flush type internal panel lock,

external pad lock and internal U clamp locking systems for against theft of panel. having 17/25 Kg weight ,16/18

guage MS weather proof with industrial exterior powder coated with 7 tank process RAL

Providing & Erecting Universal Astro 5 KVA intelligent streetlight control system insu with weather proof box for

RS: Twelve Thousand

outdoor application. (As per specification attached separately) (Make and model approved by EIC)

326 1.00 Each 12895.00 Eight Hundred Ninty Five

Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Aluminium conductor cable for 1100 volt to be

laid 90 cms. Under ground or to be laid on wall with suitable G.I. heavy guage 1.0mm thick cable clamp or in

existing DWC pipe underground or road crossing or floor.For 3*1/2 core 70 Sq. mm (35 Sq. mm * 1/2 core) ( RS: Three Hundred

Ele Room Power Supply) Seventy Five only

For 3*1/2 core 50 Sq. mm (25 Sq. mm * 1/2 core)

RS: Two Hundred

Eighty Two only

Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Copper cable for 1100 volt to be laid 90 cms.

Under ground or to be laid on wall with suitable G.I. heavy guage 1.6mm thick cable clamp or in existing DWC

pipe underground or road crossing or floor. For 4 core x 4 sq.mm. (For Street Light cable and Barrack Power RS: Three Hundred

Supply) Sixty One only

Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked unarmoured Copper cable for 1100 volt to be laid

cms. Under ground or to be laid on wall with suitable G.I. heavy guage 1.0mm thick cable clamp or in existing

DWC pipe underground or road crossing or floor. For 4 core x 10 sq.mm. (From ACDB to Solar Meter)(For 20 RS: Five Hundred

KW) Sixty Eight only

Providing & fixing Solderless crimping type Aluminium lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts

330a in an approved manner. For 16/25 Sq.mm. 6.00 Each 15.00 RS: Fifteen only

For 35/50 Sq.mm

330b 6.00 Each 20.00 RS: Twenty only

For 70 sq.mm RS: Twenty Five

Providing & fixing Solderless crimping type Copper lugs conforming to IS suitable for cable of following size

evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts

331 300.00 Each 8.00 RS: Eight only

in an approved manner. For 1.5/2.5 to 6 Sq.mm

Providing & fixing double compressed heavy duty flange type brass cable gland with rubber ring for P V C

insulated armoured cable complete with outgoing tails, insulating tape etc. For following size cables.For 2 to 4 RS: Forty Three

core x 4.0 Sq. mm (Sigma, MCI, Comet Make Only) only

For 3*1/2 core x 35.0/50.0 Sq. mm (Sigma, MCI, Comet Make Only) RS: Seventy Five

For 3*1/2 core x 70.0 Sq. mm (Sigma, MCI, Comet Make Only) RS: One Hundred

For 2 to 4 core x 10.0 Sq. mm (Sigma, MCI, Comet Make Only) RS: Forty Eight

Providing & fixing PVC cable gland with rubber ring for P V C insulated unarmoured cable complete with

outgoing tails, insulating tape etc. For following size cables. For 2 to 4 core x 6.0 to 10Sq. mm For Solar System RS: Twenty Five

Supplying following size of Light duty “A” Class G.I. Pipe & erecting as directed by Engineer-in-charge. For

mm dia. RS: One Hundred

Seventy One only

Providing & Erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of

following size to be erected as directed. For 3 core 2.5 sq.mm. PVC insulated round copper wire ISI mark. RS: Seventy Seven

For 3 core 1.5 sq.mm. PVC insulated round copper wire ISI mark.

Providing & laying HDPE Double walled corrugated pipes (DWC) (conforming to IS: 16205 (part 24) 2018)) with

minimum load required of 450N capacity with anti rodent and ultra violet material properties with necessary

connecting accessories of same material at required depth to be laid 90 cms. under ground for laying of cable

below ground / road surface for enclosing cable and back filling the same to make ground as per original. For RS: One Hundred

Outer dia. 50 mm and Inner dia. 38 mm. (Test Certificate to be Submitted) Seventeen only

For Outer dia. 90 mm and Inner dia. 75 mm. (Test Certificate to be Submitted)

RS: One Hundred

Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cms. below ground across the road crossing or on

floor with necessary material in an approved manner and making the ground as per original. For 150 mm Dia RS: Two Hundred

Supplying and erecting Fully Automatic hydro pneumatic booster system with cast iron housing Enclosure class

IP44 minimum , with built in PTO motor protection and stainless steel impeller pump, pump model GRUNDFOS

CMB 5-46 series or equivalent with 24 Liter hydro pneumatic pressurized tank capacity : 5 m3/hr,Rated head

:30 mtr, motor rating : 1.2 H.P. includes pressure switches, Non Return Valve, Pressure Gauge, 5 way Brass RS: Forty Five

338 connector, with necessary Plumbing work which includes all required size of pipes, Joints valves, Bypass valve, 2.00 Each 45679.00 Thousand Six Hundred

labor all accessories required for installation of pressure pump ( Foundation work and base stand and Control Seventy Nine only

Panel cost included)

Providing & erecting ISI make medium duty (B class) galvanized MS pipe with coupling, bend, union, reducer, RS: Two Hundred

339 tee, MS flange etc. with plumbing charges.For 50 mm dia 10.00 Mtr. 260.00

Supplying and erecting C.I. Swing check type non-return (reflux) valve ISI marked with packing, flange, nuts and

bolts etc.suitable for following pipe size. For 50 mm dia. (SANT,KIRLOSKAR,LEADER,ZOLOTO) RS: One Thousand

Ten Hundred Ten only

Supplying Water tight M.S.Box of size 20 x 15 x 15 cms. to erect suitable kitkat fuse / MCB to be . erected on

polished wooden board inside the box with hinged/sliding door with rubber rings and erected on pole with RS: Two Hundred

suitable pole clamp, all duly painted with one coat of red oxide and two coats of paints. Thirty Two only

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable RS: One Hundred

342 approved make of following Size. For 3 Core x 2.5 Sq. mm. 20.00 Mtr. 103.00

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water RS: One Hundred

343 proofing material, & making the joint complete. Up to 10Sq. mm 2.00 Each 188.00

Eighty Eight only

Supplying, Installation, Testing & commissioning of Electric driven Main Fire Pump suitable for automatic

operation and consisting of following, complete in all respects, as required: (a) Horizontal type, Single stage,

centrifugal, End Suction Long Coupled Pump of cast iron body & bronze impeller with stainless steel shaft,

mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous

speed 2900 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for

enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.

(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d)

Suitable Cement Concrete Foundation duly plastered with anti vibration pads. (e) cost include foot valve of

suitable size CI body heavy duty. (f) Discharge :- minimum 1620 LPM. Note: The head of the pump shall be RS: One lac Eighty Six

344 selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest point. Agency has to 1.00 Each 186556.00 Thousand Five Hundred

calculate the total head required for getting minimum 3.5kgf/cm2 pressure at the farthest & highest point of Fifty Six only

building of wet riser fire system. For that agency has to calculate total pump head by considering vertical head (

Total Building height+ Sump depth+3.5kgf/cm2 pressure & Total equivalent vertical head due to frication losses

of total length of pipe + bend number, Elbow number, Tee, Valve etc.) Agency must have to select pump model

having required head & discharge( asper fire department rules) at duty point. No Extra payment shall be done

for head variation due to site situation & fire rules. The panel shall be design according to motor H.P

Supplying, installation, testing and commissioning of Diesel engine driven Main Fire Pump suitable for automatic

operation and consisting of following, complete in all respects, as required: [Diesel driven pump]

(a) Horizontal type, Singlestage, centrifugal, End suction Long Coupled pump of cast iron body & bronze impeller

with stainless steel shaft, mechanical seal conforming to IS

(b) Suitable HP 2900 RPM water cooled with radiator diesel conforming to relavant IS standard complete with

auto starting mechanism 12/24 Volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 M

outside pump house duly insulated with 50 mm thick glass wool with 1.00 mm thick aluminium sheet cladding, RS: Four lac Fifty Six

345 residential silencer, instrument and protection as per standard specification, stop solenoid for auto stop in the 1.00 Each 456202.00 Thousand Two Hundred

event of fault with auto indications painted with post office red color etc. as required. Two only

(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

(d) Suitable cement concrete foundation duly plastered with anti vibration pads.

(e) Cost include providing, erecting req. size copper XLPE Armound cable with GI cable tray, support etc. as per

EIC instruction (app. cable lenth 15 mtr.)

(f) Cable from pump to panel will be laid in cable tray or fixed on G.I./M.S. strip / channel as per instructions

given by EIC as per site requirement.

(g)Cost include foot valve of Suitable size CI body heavy duty (SANT,Kirloskar, Kartar, Zoloto make)

(h)Discharge:- minimum 1620 LPM. Note: The head of the pump shall be selected in a manner so as to give a

minimum 3.5kgf/cm2 pressure at the highest/farthest point.

[The all require Technical specification & Test certificate shall be submitted to Local fire Authority for approval]

(Factory inspection will have to carried out by agency with G.S.P.H.C.L. engineer)

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for

automatic operation and consisting of following, complete in all respects, as required: (Jockey Pump).

(a) Horizontal type, Singlestage, centrifugal, End suction Long Coupled pump of cast iron body & bronze impeller

with stainless steel shaft, mechanical seal conforming to IS

(b) Suitable HP Squirrel cage induction motor, TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz

AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F'

insulation,conforming to IS :

(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

(d) Suitable cement concrete foundation duly plastered and with anti vibration pads. RS: Seventy Three

346 (e) Required size 3 core flat cable from pump to panel for connection should be provided with pump. 1.00 Each 73821.00 Thousand Eight Hundred

(f) Cable from pump to panel will be laid in cable tray or fixed on G.I./M.S. strip / channel as per instructions Twenty One only

given by EIC as per site requirement.

(g) Cost include foot valve of suitable size CI body heavy duty.(SANT,Kirloskar, Kartar, Zoloto make)

(h) Discharge:- minimum 180 LPM. Note: The head of

the pump shall be selected in a manner so as to give a minimum 3.5kgf/cm2 pressure at the highest/farthest

(Factory inspection will have to carried out by agency with G.S.P.H.C.L. engineer)

Fabrication, supply, installation and commissioning of electrical control panel of cubical construction, floor

mounted type, fabricated out of 2 mm thick CRCA sheet, compartmentalised with hinged locable doors, dust and

vermin proof, power coated of approved shade after 7 tank treatment process, cable alley, inter connection with

suitable size copeer conductor cable/solid copper strip having switchgear and accessories, mounting and RS: Two lac Seventeen

347 internal wiring, earth terminals, numbering etc. complete in all respect suitable for main fire pump, pressurisation 1.00 Each 217623.00 Thousand Six Hundred

pump and diesel pump set complete as per specification with following incoming and outgoings suitable for Twenty Three only

operation on 415 V, 3 phase 50 Hz AC supply with enclosure protection class IP 42 as required.

250A, 50 KA 4 Pole MCCB Ics=100% Icu rating.

Digital voletmeter 0-500 V with selector switch

Digital ammeter 0-250 A with selector switch and CT's etc.

LED type RYB phase indicating lamp, ON, OFF, TRIP indicationg lamps.

Set of copper busbar 300 A.

[Note:- All outgoing feeder for pumps should have digital ammeter with selector switch and LED type ON, OFF

and TRIP indicating lamps.)

MAIN FIRE PUMP:

250 A 50kA TPN MCCB Ics=100% Icu with fully automatic star/delta starter suitable for 60 HP pump with

overload protection current sensing type single phase preventor complete with all accessories and internal wiring

required for automatic operation, selector switch for local/remote, auto/manual/OFF operation.

63 A 50kA TPN MCCB Ics=100% Icu with suitable HP fully automatic Star/Delta starter with overload protection,

current sensing type single phase preventor complete with all accessories and internal wiring required for

automatic operation, selector switch for local/remote, auto/manual/OFF operation.DIESEL ENGINE CONTROL:

1) Automatic/Manual selector switch and 3 attempt starting device, timers and relay as required, push buttons,

start/stop in manual mode.

2) Indicating lamp for high/low lub oil pressure, high water temperature and engine ON indication.

3) Battery charger suitable for 12/24 V DC with boost and trickle selector switch 0-30 V DC Volt meter and 0-20

4) All standard relays and accessories for autoamtic operation of diesel engine.

SYSTEM CONTROLLER:

Design, supply, installation, testing and commissioning of system controller to control operation of main electric

fire pump, Pressurisation (Jockey) Pump, Diesel pump and terrace pump in sequence as per specification

consisting of relays, timers, sensors, annunciation window for fault indication complete as per specification.

Supplying, installation, testing and

commissioning of electric driven terrace pump

conforming to IS 12469: 2019 suitable for automatic

operation and consisting of following, complete in all

respects, as required: (Terrace Pump)

(b) Horizontal type, multistage, centrifugal, split

casing pump of cast iron body & bronze impeller

with stainless steel shaft, mechanical seal as

required. RS: Seventy Seven

348 (c) Suitable HP squirell cage induction motor TEFC 1.00 77438.00 Thousand Four Hundred

type suitable for operation on 415 volts, 3 phase, 50 Thirty Eight only

Hz, AC supply with IP55 class of protection for

enclosure, horiziontal foot mounted type with Class-

'F' insulation, conforming to IS-12615:

(d) M.S.fabricated common base plate, coupling,

coupling guard, foundation bolts etc.as required.

(e) Suitable cement concrete foundation duly

plastered and with anti vibration pads. 450 LPM at 35m head

Supplying & erecting approved make motor control cubical panel (Direct - on - line) made from 16 G. CRCA

sheet duly epoxy powder painted inside and outside with hinged doors and locking, arrangement consisting of

suitable size of ON- OFF isolator (AC - 3/23duty) main fuses, single phasing preventer, indicating lamps for R- Y -

B phases, overload relay, Automatic water level controller, Ammeter, Voltmeter each with two way selector RS: Eight Thousand

349 switch incoming, wires duly socket crimped, main contactor & overload relay, start - stop push buttons, to be 1.00 8624.00 Six Hundred Twenty Four

erected on angle iron frame grouted on wall as directed. The isolator, overload relay & contactors will be of L & only

T, Siemens or BCH make only. (B) DOL for 7.5 H.P.

Providing and fixing of Dial type Pressure Gauge having 100 mm dial & range of 0-14 Kg/cm2 with isolation ball

RS: One Thousand

valve. (Make:- Hguru, Fiebig,General Instrument) (Test certificate must be submitted)

350 3.00 Each 1539.46 Five Hundred Thirty Nine

and Paise Forty Six only

Providing and fixing of Pressure switch with Needle valve ( Indfos,Honeywell,System Sensor make and Model

RS: One Thousand

Instruct by EIC (Only)

351 3.00 Each 1415.00 Four Hundred Fifteen

Providing and fixing of Air Release Valve including Ball Valve 25 mm dia. (Approved ISI make & model

RS: One Thousand

352 approved by EIC strictly as per specification) 3.00 Each 1601.00

Six Hundred One only

Supply, Installation, Testing and Commissioning of Pump On-Off switch (with all mounting accessories

complete with Junction Box for mooting on Surface, Cable lugs at Ends, cable compression glands, cable tags

and Ferruling.)for remote operation from each floor of the building. (Approved by EIC) (Test certificate must be RS: Eight Hundred

submitted) Ninty only

Supply and laying of 3C x 6 sq.mm PVC Copper Flat cable with all require accessories for Main Pump. (Make :

Mecab, Darshan,Rimcab) RS: One Hundred

Seventy One only

Supply and laying of 3C x 16 sq.mm PVC Copper Flat cable with all require accessories for Main Pump. (Make :

Mecab, Darshan,Rimcab) RS: Four Hundred

Eighty Four only

Executing comprehensive (All-in-All) service & maintenance with spare parts as per terms & condition of tender

for Fire terrace pump with fire hydrant agency for defect liability period and copy of this contract will be submitted

before final bill. Agency has to quote rate accordingly. Agency has to also provide the fitness certificate from

system agency and submit to G.S.P.H.C.L. Agency has to submit FDR of Rs.56584.00+GST or quoted rate

whichever is higher to G.S.P.H.C.L,for minimum maturity period of Four years in favour of G.S.P.H.C.L Which

will be released after successful completion of A.M.C. & at the completion of defect liability period. Fire System

agency has to maintain written record of service & maintenance during defect liability period duly sign by police RS: Fifty Six Thousand

356 dept. and submit regularly to G.S.P.H.C.L. Agency has to give minimum three services and demonstration per 1.00 Per Tower 56584.00 Five Hundred Eighty Four

year and testing and training of pump during defect liability period and obtain necessary certificate from police only

department and submit to G.S.P.H.C.L. Agency has to do maintenance as per terms & condition alternative in

tender.Agency has to give One live demonstration of fire Mock drill for fire fighting with minimum 01 no. CO2 and

01 no. ABC type fire extinguisher at the time of handing over this system to the Police department and another at

the time of releasing final Security deposit. The necessary certificate / photographs for that must be submitted.

Executing comprehensive (All-in-All) service & maintenance with spare parts as per terms & condition of tender

for Fire terrace pump with fire hydrant agency for defect liability period and copy of this contract will be submitted

before final bill. Agency has to quote rate accordingly. Agency has to also provide the fitness certificate from

system agency and submit to G.S.P.H.C.L. Agency has to submit FDR of Rs.5342.00+GST or quoted rate

whichever is higher to G.S.P.H.C.L,for minimum maturity period of Four years in favour of G.S.P.H.C.L Which

will be released after successful completion of A.M.C. & at the completion of defect liability period. Fire System

agency has to maintain written record of service & maintenance during defect liability period duly sign by police

dept. and submit regularly to G.S.P.H.C.L. Agency has to give minimum three services and demonstration per RS: Five Thousand

357 year and testing and training of pump during defect liability period and obtain necessary certificate from police 1.00 Per Tower 5342.00 Three Hundred Forty Two

department and submit to G.S.P.H.C.L. Agency has to do maintenance as per terms & condition alternative in only

tender.Agency has to give One live demonstration of fire Mock drill for fire fighting with minimum 01 no. CO2 and

01 no. ABC type fire extinguisher at the time of handing over this system to the Police department and another at

the time of releasing final Security deposit. The necessary certificate / photographs for that must be

submitted.(For Terrace Pump)

Supply ,Installation , testing & Commissioning of heavy duty meduim voltage cable as per specficification & IS

7098 part I , 4C X 1.5 SQ.,MM ARMOURED CABLE (CU.) FRLS,RED colour with approved make , with require

support , cable tie, cable tagging , hardare are etc to complete the work.(As per BIS standard) RS: One Hundred

Supplying and erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of

following size to be erected as directed.For 1.50 Sq.mm 2 core round PVC sheathed. having insulation colour RS: Thirty One

359 RED and BLACK for Fire Alarm System. 330.00 Mtr. 31.00

SITC of Microprocessor based Net-workable Analogue Addressable Fire Alarm Control Panel. The Panel shall

be compliant with EN54-2, EN54-4 and approved by LPCB. The Fire Alarm Control Panel shall have inbuilt one

loop. The Panel must have large graphic display. The Panel must also have the capability to take Addressable

Intelligent Wired and Wireless Devices on same loop. Each loop shall have a capacity of 127 analogue

RS: Ninty Three

360 Addressable devices and 127 Base sounders/Base Sounder Beacons. The Panel shall have 240 V AC power 2.00 Each 93005.00

Thousand Five only

supply along with automatic Battery Charger. Non-Networkable

Approved by LPCB (Including Five year free maintenance with guarantee)

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector having

RS: Two Thousand

IS-11360-1985 or BS 5446 Part I-1977 & Part VII –1985 (VdS approved) or NFPA72 (UL/ULC/FM approved)

361 97.00 Each 2,415.38 Four Hundred Fifteen and

with Latest ammendment complete with mounting base complete as required. (Morley / GST/ cooper / ASES /

Paise Thirty Eight only

HUCHIKI make and model approved by EIC as per specification) [Test certificate must be submitted]

Supplying, installation, testing & commissioning of addressable manual call point having IS or BS (EN 54)

RS: Three Thousand

(Vds approved) or NFPA 72 (UL/ULC/FM approved) with Latest Amendment complete as required. (ASES

362 8.00 Each 3271.00 Two Hundred Seventy

/ravel/morley or approved by EIC as per Tender specifications) (Test certificate must be submitted)

Supplying, installation, testing & commissioning of addressable horn cum strobe having IS or BS (EN 54)

RS: Two Thousand

(Vds approved) or NFPA 72 (UL/ULC/FM approved) with Latest Amendment complete as required. (ASES

363 8.00 Each 2966.00 Nine Hundred Sixty Six

/ravel/morley or approved by EIC as per Tender specifications) (Test certificate must be submitted)

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two

LED, metallic cover complete with all connections etc as required.(Make:GST,Siemens,Morley,Copper, RS: Two Hundred

Honeywell) Twenty Nine only

Providing and fixing of ABC Type Store Pressure Fire Extinguisher Having capacity 6 kg Filled with Mono

RS: One Thousand

Ammonium Phosphate Powder 50% confirms to IS 4308, Stored Pressure Type, UGTS Pressure Gauge, Can

365 5.00 Each 1991.00 Nine Hundred Ninty One

Height 530 mm, Diameter 150 ± 10mm, Discharge Time 24 Sec, Controllable discharge mechanism, Jet Range

5 Meters, Average Discharge is 92%, applicable on Class A,B & C and electrically started Fire, Fire Rating

Providing Construction

and fixing of CO2: type

drawn & CO2 Mig

Pressure welded,

Portable 4.5 EPDM(Ethylene Propylene

kg Fire Extinguisher, Diene

filled with Monomer)

Co2 Gas as per IS

RS: Six Thousand

15222, Control discharge mechanism fitted with 1 Meter Wire Braided Hose & Electrical non-conductor

366 5.00 Each 6526.00 Five Hundred Twenty Six

Polyethylene Flat Horn with Diffuser Nozzle for dispersed discharge of CO2, Discharge Time 12 Sec, Average

Discharge is 95%, Applicable on Class B, C and electrically started Fire, Fire Rating 55B, Internal coating is not

Providing & External

fixing ofcoating is of enamel

Automatic type 5spray

kg painting, Powder Coated

Fire Extinguishers Mono Handle,

AmmoniumValvePhosphate

Confirm to powder

RS: Five Thousand

Confirms to IS 4308, Applicable fire classes A,B & C, UGTS Pressure Gauge, Can Height 370mm, Diameter

367 3.00 Each 5240.00 Two Hundred Forty

230 ± 10mm, Made up from 2 mm thick sheet, Body Construction Deep Drawn with MIG Welding technology,

Brass forged sprinkler valves with Nozzle is specially designed to give more than 99% discharge. Together with

SITC characteristic

3LCD Lamp to cover

basedadequately

projectorfire risks with

having wxgascattering coneorof better

(1280x800) 40 to 45° Angle. External

resolution Pure

with minimum white

RS: Thirty Three

brightness of 3800 lumens and color brightness of 3800 lumens. The projector should have minimum

368 1.00 Each 33560.00 Thousand Five Hundred

1HDMI,1VGA input. Having contrast ratio of 15000:1 or more. the projector should have auto vertical key stone

correction of +/- 30 degree and Manual Horizontal of +/-30 degree. the projector should have optical lens, throw

of 120 inch Zoom Factor

Self Lock MW of 1.2.

(8 x Lens focus Manual

6) Instalock having focal

Slow Retraction length Aspect

Screen, 16.9mmRatio-4:3

to 20.28mm. projector

RS: Five Thousand

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ].[Make: Da-lite / draper / liberty

369 1.00 Each 5282.00 Two Hundred Eighty Two

Supply, Installation Testing & Commissioning 15 Mtr. HDMI Interface Cable as per the detailed Specifications

supports transmission of 4K Signals as per the detailed Specifications .[Make: Kramer / Extron / Crestron] RS: One Thousand

370 1.00 Each 1760.00 Seven Hundred Sixty

SITC of universal Projector mounting kit, with necessary grouting, fasteners etc. with adjustable height and

suitable for all types of projectors. [Approved by Competent Authority i.e. not Below the rank of Executive RS: Six Thousand

371 Engineer ] 1.00 Each 6781.00 Seven Hundred Eighty

Providing and erecting water cooler having storage capacity 80 Ltr. & cooling capacity 40 Ltr.per hour @ an

ambient temp of 45˚ C. The outlet temp. of the water should drop by 15˚C within a hour, The water cooler should

be comprising of hermetically sealed compressor Reciprocating compressor with R134A gas , fan motor,

Copper Condensing unit, fan motor, water tank surrounded by evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The body of water cooler will be made from Stainless Steel, CP brass

push cock, inlet float valve, with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out

connection to FD complete as required With 20 Amp. 3 pin plug Top with indicator. (This item including

372 2.00 Each 49069.00 Thousand Sixty Nine

comprehensive service & maintanance including Spare Parts & consumable item during warranty period of one

year. Maintanance & service must be carried out by OEM dealer/distributer who has executed the work. Service

& Maintance must be as per OEM guid line.) (Agency has to give AMC to water cooler OEM / authorized dealer

upto defect liability period] [Voltas, Bluestar, Usha model approved by EIC as per specification]

Supplying & erecting 5 stage single reverse osmosis water purification system with M.S. powder coated frame,

prefilter housing with 'O' ring presediment filter GAC filter, carbon filter suitable buster DC pump capacity 80 psi,

mention with 40 psi inline type post carbon filter auto low & high pressure switches with following size of storage

tank & LPH capacity & erected as directed [B] 25 Ltr / Hr with 30 Ltr. Storage Tank [ ION EXCHANGE,

AQUAGUARD, KENT, EUREKA FORBES, RAIN DROP, Make- Power H2O, Blue mount appliances Pvt. Ltd.]

RS: Fifteen Thousand

373 2.00 Each 15466.00 Four Hundred Sixty Six

The purpose of RO plant is cater the portable and drinking water 24X7 to beneficiary.So we have taken

comprehensive maintenance contract item in this tender. Agency has to give All in All maintenance contract to

OEM of RO plant and submit AMC copy to GSPHCL at the time of final bill.Agency has to compulsory submit

FDR of Rs 27,838.00+ GST or quoted amount whichever is higher to GSPHCL. Which will be released after

successful completion of AMC & at the and of defect liability period. AMC consist of general service & Filter shall

be replaced at every 3 months.Membranes & booster pump shall be repaired/ replaced whenever RS: Thirteen

374 required.Agency has to stick maintenance schedule on the RO plant and date of service, TDS of water, 2.00 Each 13919.00 Thousand Nine Hundred

discharge of water etc. shall be written on this.Agency has to receive certificate from beneficiary every year and Ninteen only

submit at the time of releasing SD.For 25 Ltr RO plant

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with Solar Panels

(ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5,

Module Efficiency should be approx. 18%-21%, Normal operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100% Electroluminescence test to

ensure error free Modules, Thep. temp. co-efficient of the PV module shall equal or better than -0.45%/degree C. RS: Forty Two

375 Solar PV modules of minimum fill factor 75% to be used. Unit Production:- 4 to 5 Unit /kw /day (Actual)(1Year 20.00 Per KW 42035.00 Thousand Thirty Five

Avg) With 10 year Product warranty and 25 year Linear Power Warranty., only

Solar Inverter: MPPT Range: 80-1000 V, Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating

Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Anti-

islanding Protection:

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual

Current Monitoring Unit Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection

Integrated, Output Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD &

APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting Structure: Seamless Box Pipe / 'C' Channel

of suitable size for rooftop solar installations with good stability agaist wind & weight load., Hot Dipped

Galvanized steel coils. suitable arrangement for base plate for foundation , solar panel mounting, the structure

should be suitable for carry the load of solar panel,wiring, sprinkler system etc. with necessary foundation

work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be (SS 304) quality.

and Balane of System with necessary Swithgears (Suitabel size and protection of ACDB & DCDB), inter

connecting wiring, earthing system, lightining arrester system, all liasoning work with various gov. department

like state nodal agency,DISCOM & CEIG is included in agency scope

Grid Tied Solar Power System: For 20kW (3 - phase)

Executing Com of solar Pv Modules, Inverter, wiring,earthing,switchgears, etc with material and labour cost including

preventive maintanance.The cost covers entire installation. AMC also includes monthly site visit and inspection of project

with submission of inspection and solar generation report. All parts should be replaced/repaired if found faulty within

specified time. Agency has to provide necessary liasoning work for warranty,power,Bidirectional meter etc of following

Capacity as per terms & condition of tender for defect liability period.Agency has to compulsory submit FDR of approved

bank as per clause 2.0 section 3 Rs. 305100.00+ GST or quoted rate which ever is higher to GSPHCL,for minimum maturity RS: Fifteen Thousand

376 period of four years in favour of GSPHC .Which will be released after succesfull completion of AMC & at the end of defect 20.00 Per KW 15255.00 Two Hundred Fifty Five

liability period.Solar Agency has to maintain record of service & maintenance during defect liability period duly sign by only

Benificiaries and submitted regularly to GSPHCL & also get satisfactory certificate from beneficiaries at the time of Defect

liability period and copy of maintenance contract must be submitted during final bill. For 20KW

Supply, Installation, Testing & Commissioning of following size of Grid Tied Solar Power Plant with Solar Panels

(ALMM approved): Frame Material : Anodized Aluminum alloy Frame With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated), High efficency and positive power tolerance Pmax: 0/+5,

Module Efficiency should be approx. 18%-21%, Normal operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed with Bypass diodes, 100% Electroluminescence test to

ensure error free Modules, Thep. temp. co-efficient of the PV module shall equal or better than -0.45%/degree C. RS: Forty Three

377 Solar PV modules of minimum fill factor 75% to be used. Unit Production:- 4 to 5 Unit /kw /day (Actual)(1Year 10.00 Per KW 43645.00 Thousand Six Hundred

Avg) With 10 year Product warranty and 25 year Linear Power Warranty., Forty Five only

Solar Inverter: MPPT Range: 80-1000 V, Max efficiency: 97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating

Altitude (m) ≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating Tempreture Range: -25~60°C, Anti-

islanding Protection:

Integrated, Input Reverse Polarity Protection Integrated, Insulation Resistor Detection Integrated, Residual

Current Monitoring Unit Integrated, Output Over Current Protection Integrated, Output Short Circuit Protection

Integrated, Output Over Voltage Protection Integrated, Protection Degree: IP65, User Interface LCD &

APP,Datalogger & Communication: GPRS / Wi-Fi, Module Mounting Structure: Seamless Box Pipe / 'C' Channel

of suitable size for rooftop solar installations with good stability agaist wind & weight load., Hot Dipped

Galvanized steel coils. suitable arrangement for base plate for foundation , solar panel mounting, the structure

should be suitable for carry the load of solar panel,wiring, sprinkler system etc. with necessary foundation

work/wall mount, j bolt, anchor fastner etc. the nut bolt used for installtion of stucture should be (SS 304) quality.

and Balane of System with necessary Swithgears (Suitabel size and protection of ACDB & DCDB), inter

connecting wiring, earthing system, lightining arrester system, all liasoning work with various gov. department

like state nodal agency,DISCOM & CEIG is included in agency scope

Grid Tied Solar Power System: For 10kW (3 - phase)

Executing Com of solar Pv Modules, Inverter, wiring,earthing,switchgears, etc with material and labour cost including

preventive maintanance.The cost covers entire installation. AMC also includes monthly site visit and inspection of project

with submission of inspection and solar generation report. All parts should be replaced/repaired if found faulty within

specified time. Agency has to provide necessary liasoning work for warranty,power,Bidirectional meter etc of following

Capacity as per terms & condition of tender for defect liability period.Agency has to compulsory submit FDR of approved

bank as per clause 2.0 section 3 Rs. 165270.00+ GST or quoted rate which ever is higher to GSPHCL,for minimum maturity RS: Sixteen Thousand

378 period of four years in favour of GSPHC .Which will be released after succesfull completion of AMC & at the end of defect 10.00 Per KW 16527.00 Five Hundred Twenty

liability period.Solar Agency has to maintain record of service & maintenance during defect liability period duly sign by Seven only

Benificiaries and submitted regularly to GSPHCL & also get satisfactory certificate from beneficiaries at the time of Defect

liability period and copy of maintenance contract must be submitted during final bill. For 10KW

Total Of Electrical item Amount in Rs.

Total Electrical Say Amount In Rs.

Assistant Engineer (Ele.) Dy. Ex. Engineer (Ele.)(S.P) Executive Engineer (Ele.)

Ahmedabad Gandhinagar Gandhinagar