SPECIAL REPAIR TO BLOCK NO. P-364 AND PROVISION OF CERTAIN REVENUE/MINOR WORKS UNDER AGE B/R II AND AGE E/M AT MILITARY STATION KOTA

Amount

Demolition/Dismantling of existing normal roof treatment, any type from RCC roof slab incl wire brushing and cleaning of foreign materials, dust etc, complete all as specified and directed.

M&L brushing neat cement slurry with 3.00 kg cement per Sqm, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-0 (Using 12.5 mm graded stone agg) for filling in pressed steel frames, roof padding, leveling course to receive floor finishes etc complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of RCC roof slab in CM 1:3 duly mixed with liquid water proofing compound, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

Supply only liquid water proofing compound Dr Fixit LW+ or equivalent as approved by the GE, complete all as specified and directed.

M&L for cleaning of roof slab including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS 3384 @ of 0.40 Kg/Sqm torching overlaps with a propane or a butane gas torch, with a overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold emulsion bituminous primer all as per manufacturer’s instructions complete all as directed. Note: (i) Coved fillets in PCC(1:2:4) type B-0 using 12.5mm graded stone aggregate, of radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of Grade 30/40 confirming to IS-73, [email protected] Kg/Sqm over a coat of cold applied bituminous primer conforming to IS:3384 @ 0.40 Kg/Sqm.

Item 6.00 Contd..... (ii) Polymeric membrane shall be taken to a height of 45cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing. (iii) The waterproofing treatment shall be got carried out by the manufacturer or their authorized applicators. (iv) In case of stone masonry parapet wall etc a groove of size 25mmx25mm (minimum) shall be made in coved fillet at the junction of roof and parapet wall/mumty Chimney/other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen. (v) Above aspects are deemed to be included in quoted rate.

M&L for cleaning of walls and floor of sunken portions including picking, sweeping clean and washing down with water to remove dust, dirt etc and Supply and fix APP polymeric water proofing membrane, minimum 3mm thick and weighing not less than 3.0 Kg/Sqm, black finish reinforced with non-woven polyester matt, with a thermo fusable finish laid over cold applied bituminous primer conforming to IS: 3384 @ 0.40 Kg/Sqm, torching overlaps with a propane or a butane gas torch with an overlap of 75mm at the sides and 100mm at the ends and sealing including applying a coat of cold applied bituminous primer all as per manufacturer’s instructions, complete all as directed. Note: (i) The waterproofing treatment shall be got carried out through the manufacturer or their authorized applicators only.

M&L for providing 40 mm bore GI medium grade pipe as spout in sunken floor including cutting holes in brick walls/RCC, built in cement mortar and making good the dismantled portion in PCC 1:2:4 type B-1 with using 20 mm graded stone aggregate and finishing the same to match with external surface, complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors etc, laid, bedded and pointed in any mortar, complete all as specified and directed.

M&L for 15 mm thick rendering on other than fair faces of brick/concrete surfaces in two layers, consisting of 10 mm thick in CM 1:6 and over that 5 mm thick in Cm 1:4 using water proofing compound as per manufacturer's instruction's, finishing surfaces even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only approved integral water proofing compound, complete all as specified and directed.

M&L for applying two coats of cement based paint over a coat of primer on newly plastered surfaces of walls including preparation of surfaces, complete all as specified and directed.

M&L for preparing new previously untreated plastered surfaces of walls and applying 1 to 1.50 mm thick layer of wall care putty and over it applying two coats of modified exterior acrylic emulsion paint over a coat of primer, complete all as specified and directed. (Make: Asian paints - Apex Ultima, ICI Dulux - Weather Shield Max, Berger - Weather Coat Long Life, Acro Paints - Acroguard 3X)

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc. complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc 15 cm thickness (below or above GL), complete all as specified and directed.

M&L 75 mm thick PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in sub base of floors etc, complete all as specified and directed.

M&L for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in flooring/sub base finished rough to receive floor finishes/screed complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L Glazed ceramic coloured tiles on vertical surfaces 300x 250x7 mm/450X300X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, laid over and including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

M&L for machine cut kota stone slab as in skirting, dado, risers etc, 17 to 22 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing and polishing, laid over and including 10 mm thick CM 1:4 backing, complete all as specified and directed.

M&L polished baroda green slabs, 18-20 mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of marble stone including grinding and polishing complete, laid over and including 15 mm thick screed in CM 1:6, complete all as specified and directed.

M&L complete removal of existing treatment from previously treated surfaces of walls and applying 1 to 1.5 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm dia pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm dia pipes complete all as specified and directed.

Taking up or down existing GI tubing and connections, including making good the disturbed surface for 25 mm dia pipes complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Supply, fixing, laying & testing 25 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 15 mm dia pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 20 mm dia pipes with and including all new fittings complete all as specified and directed.

Refixing old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) for 25 mm dia pipes with and including all new fittings complete all as specified and directed.

Dismantling water storage tank of any description of capacity exc. 250 ltr but n.exc. 500 ltr, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 500 lts capacity (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed.

S&F 20 mm dia ball brass valve, high pressure with polythene float and fly nut, screwed down for iron pipe, complete all as specified and directed.

S&F 20 mm dia stop valve, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for union, complete all as specified and directed.

S&F mild steel flat iron fillets for securing wire mesh including all necessary drilling, riveting and bolting etc, complete all as specified and directed.

S&F 5 to 10 mm dia MS screw bolts (Purpose made ) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut, length of bolt not exc 5 cm long, complete all as specified and directed.

S&F 100 mm long mild steel cold rolled medium weight butt hinges, fixed with MS screws, complete all as specified and directed.

S&F 100 mm Hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest incl providing lime concrete bedding and connecting to flusing cistern, complete all as specified and directed.

S&F 10 Ltr vitreous china valveless syphonic action type flushing cistern, low level, coloured with inlet, ball valve, float and handle incl PVC flush pipe of 32 mm dia, fixed to wall, complete all as specified and directed.

S&F in repair swivel shower rose of CP brass, 75 mm dia, for fixing with 15 mm pipe with shower arm 15 mm size, 195 mm long with bend of 45 degree with flange of CP brass, complete all as specified and directed.

S&F 'D' type towel rail 60 cm long, stainless steel, fancy type, 20 mm dia complete fixed with steel screws complete all as specified and directed.

S&F in repairs stainless steel utensil plate rack of size 900x1000x200 mm, made of 24 gauge thick stainless steel sheet and fixed in position, design and pattern as approved by the GE, complete all as specified and directed.

S&F in repair sink with draining board made of stainless steel 1mm thick with plugs, washers and waste coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets of suitable angle iron, 32 mm dia superior quality PVC waste pipe and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair vitreous china wash hand basin flat back 550 x 400 mm excluding tap but including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe with connector, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed.

S&F pillar taps, cast copper alloy, with capston heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed.

S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers, complete all as specified and directed.

S&F in repair 15 mm dia bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair 15 mm dia stop valve, cast copper alloy, chromium plated fancy type, screwed down high pressure with capstan head, screwed both ends for iron pipes or for union, complete all as specified and directed.

S&F in repair 15 mm dia bib taps, cast copper alloy, fancy type, chromium plated, long body with capstan head, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair stainless steel tubular curtain rods, 25 mm dia, with fixing brackets and one pair of decorative end caps etc, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and directed.

S&F 3mm thick sheet glass, obscured or frosted on one side, ordinary quality and glazing with oil putty etc in squares n.exe 0.50 Sqm in each pane, complete all as specified and directed.

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 75 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes 100 mm bore, jointed in CM and taking out from trenches if required, complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 75 mm bore in any length with or without ears with cement joints laid in trenches or in floor, complete all as specified and directed.

S&F sand cast iron soil, waste and vent pipe 100 mm bore in any length with or without ears with cement joints laid in trenches or in floor, complete all as specified and directed.

S&F 100 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured), complete all as specified and directed.

S&F 75 mm bore CI bend (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and directed.

S&F 100 mm bore CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F 75 mm bore CI branch pieces, single (equal or unequal) ordinary or inverted or with parallel branches, complete all as specified and directed.

S&F stack clamps made out of 50x5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof, bore of pipe 100 mm, complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc., complete all as specified and directed.

S&F mild steel framed work as in grills, grating etc. with end of bars shouldered and/or riveted, or forged into spikes: framed guard bars: barred iron doors: ladders: frame balusters: walk ways: railing: frame work of water tanks and similar works conforming to Fe-290 Grade-E-165, complete all as specified and directed.

S&F steel windows or ventilators with side hung shutters including box type friction hinges, steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of zinc chromate primer complete all as specified and directed.

S&F steel windows or ventilators with side hung shutters including box type friction hinges, steel handle and steel peg stay, complete without glazing bars, including one shop coat of zinc chromate primer complete all as specified and directed.

S&F in repair MS handle of standard size and pattern for steel window including necessary nut, bolt and washer, compete all as specified and directed.

S&F in repair MS peg stay of 300 mm size for steel window including necessary nut, bolt and washer, compete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples, complete all as specified and directed.

M&L for preparing new steel surfaces exceeding 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide zinc chromate primer, complete all as specified and directed.

M & L for preparation of old painted steel, surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking taking off shutters from the frame) n. exc. 1.50 Sqm each, complete all as specified and directed.

Taking down Chowkats or frames with shutter (without taking taking off shutters from the frame) exc. 1.50 Sqm and n. exc. 4.00 Sqm each, complete all as specified and directed.

M&L for 25 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock/Bijasal) paneled door shutters single panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S&F 35mm thick factory made IInd Class Hard wood (Hollock/Bijasal) glazed and skeleton, open rebated, prepared to receive glass, gauge etc, without sash bars, edges of framing plain, chamfered and rounded, fitted with cut and mitered beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

M&L rolled mild steel door frames made of angle iron with and including hold fasts and FI thresh hold etc, and fixed to openings, conforming to Fe-290 Gde E-165, complete all as specified and directed.

S&F Wire netting of galvanised steel wire 2.00 mm dia fixed with tinned tacks of wire staples, size of mesh 20 mm, complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F 150 mm aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed.

S&F 50 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type E-22, complete all as specified and directed.

S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed.

S&F aluminium handles, cast type, anodised 125 mm size, fixed with screws, complete all as specified and directed.

S&F continuous piano hinges, mild steel bright finish or electro galvanised, 40 mm width, complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140 mm, complete all as specified and directed.

S&F 18/19 mm thick block boards, grade 1 quality, exterior grade with decorative face veneer on both faces including providing 6 mm thick teak wood beading on exposed edges, fixed with screws to timber frame work, complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces, exceeding 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M & L for preparation of old painted surfaces of wood or wood based materials of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and directed.

Taking down cement plaster of any description and thickness on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or stone masonry surface in cement mortar 1:6, surface finished even and smooth without using extra cement, complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:4 on concrete surfaces of ceiling, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for applying two coats of cement based paint on old previously treated plastered surfaces of walls including preparation of surfaces, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of ceiling, complete all as specified and directed.

M&L for preparation of old previously decorated plastered surfaces of ceiling and applying one coat of white wash, complete all as specified and directed.

Demolition of brick work or stone/boulders masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facing, dressed stone work & precast concrete articles complete all as specified and directed.

M&L walling of random rubble, uncoursed well bonded, bedded and solidly hearted, built in Cement Mortar 1:4, complete all as specified and directed.

M&L brick work with pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan exc 6 m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100 mm thick as in sub base, finishing the surface fair and even, complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block any shape and size made with grey cement and pigment, confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade, laid over and including 25 mm thick sand cushion, complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar not exc. 150 Sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1(using 20 mm graded stone aggregate) depth exc. half brick and not exc. one brick, complete all as specified and directed.

S&F glass shelf assembly of 6 mm thick glass, 12 cm wide and 60 cm long and CP guards of approved quality and fixed to wall with CP brass screws etc, complete all as specified and directed.

S&F soap dish made of stainless steel, approx size 160x100 mmx 1 mm thick, fixed to walls with plugs & SS screws, complete all as specified and directed.

Demolition and breaking up drain pipes and fittings, salt glazed ware, AC, PVC or RCC, internal dia of pipe 150 mm, complete all as specified and directed.

M&L for 150 mm dia salt glazed stoneware drain pipes, laid in trenches and jointed in cement sand slurry in 1:1, complete all as specified and directed.

S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and laid in trenches/floor, complete all as specified and directed.

M&L PCC 1:4:8, type D-2 using 40 mm graded stone aggregate, as in concrete bed to drain pipes including packing under and haunching against the sides of 150 mm dia pipe, after they are laid and tested, complete all as specified and directed.

M/L for 50mm thick rough dressed stone slabs for manhole covers n.exc 2 mtr in length, punched dressed on face and along exposed edges, self faced on other side and sets and pointed in cement mortar 1:4 complete all as specified and directed.

M&L Providing cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate), 75 mm thick as in plinth protection/Path/PCC paving etc including finishing the surface even & smooth without using extra cement, with and including all necessary formwork to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints throughout the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three parts of fine sand by weight), complete all as specified & directed.

M&L for providing water proofing treatment to RCC roof/chajja surface, edges, soffits etc in following stages: - i) Preparation of surfaces by cleaning of dust, washing with water etc and filling cracks with approved crack filler compound. ii) Applying 5 mm thick rendering in CM 1:3 and finishing the surfaces even and smooth without using extra cement. iii) Applying three coats of heavy duty elastic & resilient acrylic polymer, reinforced with micro fibers & fungicidal @ 0.50 liters per Sqm in each coat and dried for 6-8 hours after each coat with and including woven glass fiber mesh 2.5mm x 2.5mm put between first and second coat.

Excavation in post holes (or similar holes) Each n exc 0.50 Cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm, watering and removing surplus soil to a distance of n exc 50m and making good surface in soft/loose soil, complete all as specified and directed.

M&L PCC 1:3:6 type C-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

Supply, fabrication and fixing MS tubes, medium grade with connecting plates as in posts and struts including cutting to shape, provided with necessary nuts, bolts, washers, welding etc, complete all as specified and directed.

Supply, fabrication and fixing MS square/rectangular tubes, medium grade with connecting plates as in framed truss, purlin, rafter etc including cutting to shape, provided with necessary nuts, bolts, washers, welding etc, complete all as specified and directed.

S&F Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed.

M&L for brick work with pulverised fuel Ash-lime bricks (Fly ash bricks - non modular size), straight or curved on plan to any radius in half brick walls built in cement mortar 1:4, complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4, surface finished fair and even without using extra cement, complete all as specified and directed.

M&L for non skid ceramic coloured tiles, 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles, laid over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

S&F vitreous china half stall type urinal, white with grating and union for discharge pipe, including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back with white cement, complete all as specified and directed.

S&F 32mm dia waste coupling of PTMT (half or full threaded) minimum weight not less than 45 grams, complete all as specified and directed.

S&F urinal spreader of PTMT (Minimum weight 60 Gms), any colour for fixing with 20 mm dia pipe, complete all as specified and directed.

S&F vitreous china urinal partition, white, size 310x700 mm, fixed to wall and pointing around edges in white cement, complete all as specified and directed.

S&F PVC (SWR) bend 110 mm bore, any radius, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) bend 110 mm bore, any radius with oval access door, incl jointing to waste pipe with solvent cement, complete all as required and as directed.

S&F PVC (SWR) vent cowl 110 mm bore, incl jointing to waste pipe with solvent cement, complete all as specified and directed.

S&F 15 mm dia bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

M&L cutting existing manholes for connecting new drain (for 100 mm bore pipe), making good to pipe and rendering, cutting out existing benching for forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B-1 or smooth finishing, complete all as specified and directed.

S&F steel windows or ventilators with top hung shutters including box type friction hinges, steel handle and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of zinc chromate primer complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or stone masonry surface in cement mortar 1:6, surface finished even and fair, complete all as specified and directed.

M&L preparing previously untreated plastered surfaces of walls and applying 1 to 1.5 mm thick Wall care putty as per manufacturer's instructions and over it applying two coats of distemper oil emulsion over a coat of primer, complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white including plastic seat cover white with flat bottom and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

S&F in repair vitreous china wash hand basin flat back 560 x 430 mm with pedestal excluding tap but including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe with connector, brackets 2 numbers including cutting for and pinning in ends of brackets complete all as specified and directed. (Make Jaquar Cat Part No. C-0491 & C-0477 or equivalent in Roca/RAK)

S&F 15 mm bore CP brass centre hole basin mixer for mixing hot and cold water, screwed down for iron pipe and fixed, complete all as specified. (Make - Jaquar, Cat Part No. VGP-81011B or equivalent in Plumber/Grohe)

Dismantling water storage tank of any description of capacity exc. 500 ltr but n.exc. 1000 ltr, complete all as specified and directed.

S&F in position rotational moulded polyethylene water storage tanks 1000 lts capacity (cylindrical vertical with closed top) hoisted and fixed in position, complete all as specified in SSR Part I and as directed.

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m deep for foundation etc or for shafts, column footings or for laying cables etc not exc 10 Sqm on plan and getting out in soft/loose soil, complete all as specified and directed.

Removing excavated soil to a distance exceeding 50 m but not exceeding 100 m and depositing where directed at a level not exceeding 1.5 m above the starting point, complete all as specified and directed.

Returning filling in soil including spreading, leveling, watering and well ramming in layers not exc 25 Cm, complete all as specified and directed.

M&L PCC 1:4:8 type D-2, using 40 mm graded stone aggregate, as in foundation, filling, mass concreting etc, complete all as specified and directed.

M&L hardcore (broken stone) of gauge not exc 63 mm, deposited spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4 mix type B1 (Using 20mm graded stone agg) as in flooring, finishing surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, conforming to Fe 410 -W (GdeE- 250) quality A, complete all as specified and directed.

M&L applying three coats of white wash after preparation of new plastered surfaces of walls, complete all as specified and directed.

Supply & fix 2mm thick (minimum) aluminium sheet fixed on existing frame work/posts using stainless steel nuts, bolts, washers etc & 6mm dia aluminium rivet. Front face of aluminium sheet shall be covered with white diamond grade micro Prismatic type IX ASTMD 4956-01 standard retro reflective sheeting, letter material by overlay colour film (colour as approved by the GE) pasted over white prismatic sheeting and back side of board shall be painted with epoxy colour of shade as approved, complete all as specified and directed.

M&L cutting openings through brick walls for door, windows and other openings or enlarging existing openings, converting window into door openings etc or cutting out defective brick work for under pinning including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard core etc to store and rubbish off the premises not exceeding 50 metres, complete all as specified and directed.

M&L for PCC 1:2:4 mix type B-1 (Using 20mm graded stone agg) as in bed blocks for fixing hold fasts, bolts etc, complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100mm long (2 No.) suitable handle (1 No), complete all as specified and directed.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F Solar control film 50 micron thick , reflective type, sticked to glass panes as per manufacturer's instructions, complete all as specified and directed.

S&F door closer hydraulically regulated, aluminium die cast body, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm width and weight between 61 to 80 Kg and fixed, complete all as specified and directed.

S&F 12 mm thick block boards, grade 1 quality, exterior grade with decorative face veneer on one face and commercial type on other face including providing 6 mm thick teak wood beading on exposed edges, fixed with screws to timber frame work, complete all as specified and directed.

M&L 4 mm thick high pressure steam cured Non asbestos fibre cement reinforced multipurpose building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws and applying three coats of white wash after preparation of surfaces, complete all as specified and directed.

S&F Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605 mm, complete all as specified and directed.

S&F in repair 4 mm thick AC sheet plain building board fixed to timber frame work with screws complete all as specified and directed.

S&F in repair 15 mm bore CP brass wall mixer with hi flow divertor for mixing hot and cold water, screwed down for iron pipe and fixed, complete all as specified. (Make - Jaquar, Cat Part No. VGP-81079K & ALD-079 or equivalent in Plumber/Grohe)

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed, complete all as specified and directed.

S&F 18/19 mm thick block boards, grade 1 quality, exterior grade with decorative face veneer on one face and commercial type on other face including providing 6 mm thick teak wood beading on exposed edges, fixed with screws to timber frame work, complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for reuse or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Dismantling unserviceable main switch/DBs incl wooden board and deposit to MES store yard including making good disturbed surface of wall complete all as specified and directed.

Taking down sub main wiring of any size/capacity complete all as specified and making good disturbed surfaces to match with the existing surface, complete all as specified and directed.

M&L for Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 1.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface including making good disturbed surface all as specified and directed for the following: - One light/ceiling fan/exhaust fan/bell buzzer point controlled by one, one way switch of 5/6 Amps.

One 5 Pin, 5/6 amps socket outlet point on independent board, controlled by one, one way 5/6 Amp switch.

One 5 Pin, 5/6 amps socket outlet point on same board, controlled by one, one way 5/6 Amp switch.

One light point controlled by two, two way 5/6 Amp switches.

M&L Point wiring with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable of size 2.5 Sqmm, with PVC insulated (FRLS) unsheathed multi stranded copper conductor cable FRLS of size 2.5 Sqmm as earth continuity wire to be drawn in and including PVC casing capping not less than 20 mm width with all accessories and fittings, fixed on surface for one socket outlet 15 amp on independent board including making good disturbed surface, complete all as directed and specified.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F switch piano flush type 5/6 Amps, 230 volts, single pole, two way, ISI marked, complete all as specified & directed.

Supply and fixing switch socket combination, 5/6 and 15/16 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing switch socket combination, 5/6 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

Supply and fixing socket outlet, 5/6 Amps, 230 volt, multi pin, flush type universal, complete all as specified and directed.

S&F stepped type electronic fan regulator, flush type, 230 volts AC, single pole, humming free, fixed on the existing phenolic laminated sheet, complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65x 20mm, 3 terminals, complete all as specified & directed.

S&F switch bell push, 5/6 Amps, 230 volts, single pole, one way, ISI marked, complete all as specified & directed.

S&F bell electronic, ding dong type, 230 volts, single pole, ISI marked, complete all as specified & directed.

S&F LED Tube light fittings, batten type with bipin holders, powder coated steel with retrofit 20 watt LED tube, internally prewired, complete all as specified and directed.

S&F PVC/polycarbonate lamp holder, angular/batten type with back plate, complete all as specified & directed.

S&F MCB, 6 to 32 Amps, Single Pole, 240 Volt, 10 KA 'C' series including all accessories, complete all as specified and directed.

S&F MCB, 6 to 32 Amps, Single Pole & Neutral, 240 Volt, 10 KA 'C' series including all accessories, complete all as specified and directed.

S&F MCB, 63 Amps, Triple Pole & Neutral, 415 Volt, 10 KA 'C' series including all accessories, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 415 Volts TPN with 4 ways, Double door, complete all as specified and directed.

M&L for MCB DB made of sheet steel phosphatised, powder painted with bus bar 200 A, neutral link, earth bar and Din rail, 240 Volts SPN with 8 ways, Double door, complete all as specified and directed. Note for items of MCB DB's: - (1) The unit rate includes for cutting the brick walls to accommodate DB to make flush to wall. (2) The unit rate includes for making good the disturbed surfaces including finishes to match with the adjoining surface.

S&F of sub main wiring with two runs of single core PVC insulated and unsheathed FRLS multi-stranded copper conductor cable of size 6 Sqmm LT, 1100 volts grade, drawn through and including minimum 25 mm wide PVC non metallic surface casing/capping with all accessories and fittings and one run of 6 sqmm single core multi-stranded FRLS copper conductor cable green colour as earth continuity conductor complete all as specified & as directed. NOTES for sub main wiring:- (i) Two runs of cable one run of earth wire and one run of PVC non metallic casing/capping shall be measured as one run length. Cable required for connection to DBs shall deemed to be included and shall not be measured separately. Earth wire shall run inside the PVC casing/capping.

M&L for Earthing with galvanized steel earth plate electrode of size 600 mm x 600mm x 6.0 mm, buried directly in ground (earth plate not less than 2.25 Mtr below normal ground level) connected to galvanized earth lead strip of size 25mm x 4 mm by means of bolts, buts, check nuts and washers of galvanized iron on steel including 40 mm dia light grade GI tubing for protection of earth lead, MS sheet metal funnel with wire mesh, watering pipe medium grade 20 mm dia, charcoal or coke and common salt in alternative layer of 15 Cm compacted thickness all around the electrode with concrete earth pit of PCC 1:3:6 type 75 mm thick precast RCC (1:2:4) type B1 pit cover reinforced with 8 mm dia deformed bar and suitable handle made of 10 mm dia round bar including GI strip of size 25 mm x 3 mm for extension of earth lead and necessary excavation, earth work, in soft/loose soil and disposal of spolis to a distance not exc 50 Mtr and necessary connection and testing complete all as shown in electrical plate No. 3 and complete all as specified and directed. Notes: - (a) Irrespective of whatever is shown in plate No 5 of SSR, earth pit shall be casted in PCC (1:3:6) type C-1 and precast cover of RCC (1:2:4) type B-1 with suitable handle. (b) Item includes the cost of GI pipe for protection of earth wire/strip and earth strip upto 7.5 m. Any variation below or above shall be measured and paid for separately under relevant item of this Sch ‘A’.

S&F LED security light fitting, 24 watt, pressure die cast aluminium housing with IP 66 deg of protection, complete with 1.20 m long street light swan neck shaped bracket made of 40 mm bore GI light grade tubing, fixed on pole/walls including necessary FI clamps, nuts, bolts, washers etc, complete all as specified and directed. Make: Philips/Surya/Bajaj.

Disconnecting and taking down carefully ceiling fan/exhaust fan and refixing the same after rewiring work, complete all as specified and directed.

Supply, Laying, jointing and testing of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable, heavy duty, with 25 Sqmm, 3.5 core aluminium conductor, 1100 Volts grade, complete all as specified and directed.

M&L for dry and fine river sand free from sharp material as in cushioning to cable in trenches for cable protection including necessary punning and consolidation as required complete all as specified and as directed. (Depth of sand shall be measured after punning).

Supplying and laying pulverized fuel Ash-lime bricks (Fly ash bricks - non modular size), laid flat adjoining each other as in protection to UG cables, complete all as specified and directed.

S&F Tubes "light grade" galvanised iron of 40 mm bore, laid under roads/drain, fixed to poles, walls, with flat iron clamps, bolts/ nuts/ washers etc, complete all as specified and directed.

S&F PVC rectangular block for mounting switches, sockets, fan regulators etc with 3 mm thick plastic laminated sheet cover of size 100x100 mm and 50 mm deep, complete all as specified and directed.

All as per item 206 above but of size 175x100 mm and 50 mm deep, complete all as specified and directed.

All as per item 206 above but of size 200x150 mm and 50 mm deep, complete all as specified and directed.

All as per item 206 above but of size 250x200 mm and 50 mm deep, complete all as specified and directed.

Supply, installing, commissioning and testing energy efficient BEE 3 star rated split type air conditioner with intelligent remote control, 220Volts AC, nominal capacity 1.5 TR, complete with copper condensing tubing designed for outside ambient temperature (summer 50 degree celcius, monsoon 32 degree celcius), relative humidity 50% to 60 %, number of air changes 3-4 per hour, copper refrigerant piping with insulation (EP foam pipe section) upto 3 metre from indoor unit to outdoor unit with copper power cables upto 4 mtr including supply, fixing/grouting a set of best quality mounting brackets for outdoor unit, complete all as specified and directed.

Supply, installing, testing and commissioning Voltage stablizer for automatic operation, single phase naturally air cooled, indoor type and designed for input voltage of 170-260 volts with out put voltage stablized at 220 volt with accuracy of +/-1.00%, capacity 5.0 KVA, mounted on wall with suitable arrangements, complete all as specified and directed.

S&F three runs of 1.50 Sqmm PVC insulated single core multistranded copper conductor cable, unsheathed, 1100 volts grade, drawn through and including 20 mm bore PVC medium grade conduit with all fittings, fixed on surface/pole/wall with clamps/saddles, complete all as specified and directed. (Three runs of cable and one run of PVC conduit shall be measured as one unit)

ONKAR ENGINEERS

Shiv Construction Company

L P Singh and Co.

SINGH ENTERPRISES

M/S GAURI CONSTRUCTION