PROVN OF LIFT BOX FOR SPL ABLED STUDENTS OF CAP SIX PASSENGERS AT APS JODHPUR AT ARMY AREA UNDER GE (A) NO. 01

Amount

Excavating over areas, n exc 1.5 m deep and getting out for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Soft/disintegrated or Hard Rock (any type) complete all as specified and directed.

Excavating over areas, exc 1.5 m deep and getting out for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m in depth or part thereof in depth beyond the first 1.5 m and getting out Soft/disintegrated or Hard Rock (any type) complete all as specified and directed. Note for item No. 01 & 02 above :- Hard rock met with during excavation shall be entered in the measurement book duly signed by the GE and contractor and the same shall become the property of the contractor for which recovery at the rate of supply only rate for hand packing i.e. Rs. 1500.57 per cubic metre (Solid contents) (item 06123 of MES SSR Part-II) (irrespective of actual size of boulder/aggregate obtained) shall be made subject to applicable percentage over SSR from contractor's advance on account payment.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in flooring,path , sub foundation etc complete all as specified and directed.

M&L for Brickwork with fly ash bricks (old size), straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

Returning , filling in soft/ disintegrated (any type) incl spreading levelling, watering and well ramming in layers not exceeding 25 Cm thick all as directed.

Removing surplus soil excavated material exc250m but n.exc 500m where directed at a level not exceeding 1.5 Mtr above the starting point all as directed.

M&L 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar places, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 40mm thick cement concrete type B-0 1:2:4 (using 12.5 mm graded crushed stone aggregate as in floor finishing the surface even & smooth without using extra cement) complete all as specified and as directed.

M&L RCC Design mix M-25 using 20 mm graded stone aggregate Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L RCC Design mix M-25 using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L RCC Design mix M-25 using 20 mm graded stone aggregate as in beam, roof beam, cantilevers, lintel beam, etc. complete.

S&F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S&F mild steel TMT bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

Use and waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surface of concrete complete all as specified and directed.

Use and waste of Formwork Square,rectangular or polygonal fair finished sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface of concrete complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs etc. also splays between floors and beams, etc. for fair finished surface of concrete complete all as specified and directed.

M&L 16-18 mm thick black granite machine cut one side polished as in wall cladding of Lift gate Jambs/wall set and jointed including 20 mm thick screed bed in cement mortar 1:3, laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 over brick wall surfaces incl finishing the surface fair etc complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on concrete or wall surface complete all as specified & directed.

Supply only water proofing compound .

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

Supply, installation, testing and commisioning of passenger Lift of capacity 6 persons /408 kg , with 3 opening, safty accests such as fire fighting cyllender ABC type, emegency opening at nearest down, battery backup, telephone, emergency bell , Internal flame proof/safty lights, etc complete all as directed by EIC and compiled as following Notes:

Technical Specifiaction-1

Quantity-: 1 (One Units)

Model-: meta100 MRL

Assembled Product-: Passenger Elevator

Capacity-: 6 persons, 408 kg

Speed-: 1.00 m/s

Stops & Openings-: 3 Stops, 3 Openings

Floor designations-: G,1,2

Machine type & Location-: meta100 MRL - Gearless machine located in the shaft on top of the guiderails

Drive-: ACVVVF

Power supply-: 415 volts, 3 phase, 50Hz, AC

Hoist way dimensions-: 1800mm wide x 1700mm deep

Car travel-: 9000mm

Overhead-: 4200mm

Pit depth-: 1530mm

Car dimensions-: 1000 mm wide x 1100mm deep x 2200mm high

Door opening-: 800mm wide x 2000mm high

Car door-: 2 panel automatic center opening door with ACVF drive in Stainless steel Silver Sky finish

Landing door (Group1)-: 2 panel automatic center opening door in Stainless Steel Silver Sky finish on 3 floors

Landing door (Group2-: 2 panel automatic center opening door in Stainless Steel Silver Sky finish on 0 floors

Car design-: Prime- Stainless steel Silver Sky (Hairline) finish

Stainless Steel Silver Sky finish with Square LED for car lighting

Car flooring-: 20mm recess provided for granite/marble flooringprovide by contractor

Natural mirror in car-: Natural mirror of half car height and full car width provided on rear wall of car

Handrail-: Round handrail in Stainless Steel finish provided on rear wall of car

Landing operating panel-: Individual landing operating panel for each elevator

Features Included

ACVVVF closed loop drive

Alarm button in car operating panel with battery back-up

Automatic operation for car fan

Adjustable door open time

Anti-nuisance (empty car)

Anti-nuisance (car call cancellation at direction reversal)

Blower fan in car for ventilation

Braille on push buttons

Car call cancellation by double pressing floor button in car operation panel

Door open and door close buttons in car operating panel

Door closing retries

Door nudging

Emergency light

Full load by-pass

Home landing

Infra-red screen for car door

Intercom

Jammed landing operating panel call button by-pass

Motor overheat protection

Overload function with audio-visual indication in car operating panel

Phase failure and phase reversal protection

Automatic rescue device in case of power failure

Attendant control

Red dot matrix scrolling display in car operating panel

Red dot matrix scrolling display in landing operating panel on All Floors

Fireman control

Fireman emergency return

Provision of additional cores in travelling cable for CCTV camera signals/music system wiring

Voice announcement unit in English language in car

RCC Socle for car and counter weight buffers

INSTRUCTION:- TO BE COMPILED TO CONTRACTOR

Store security ( including on- site / off site stores and stored material/ products within or outside storage area will be lasie by contractor with USERs

Shifting of Materials/Products within the site (including shifting from existing store to another store or location on client’s request) except for the purpose of Installation of Products is resonsibility of contractor

Provision of dry and clean machine room with provision of cross ventilation (through exhaust fan), sufficient machine room lighting, lockable door (2m x 1m, outside opening type), with provision of rain protection guard on doors and windows, direct approach from terrace to machine room by a stairs or through rigid ladder with handrails and fall protection rails, trap door cover, fire extinguisher, smoke vent of suitable size in shaft covered with wire mesh are responsibility of contactor

Provision and maintenance of adequate light points/ lighting and lux level inside elevator shaft (including at each landing, machine room and the elevator pit)/ escalator pit are responsibilty of contractor

Provn of ANB type cyleners 6 kg - 5 Nos inclding installtion for easy movement on rack/wall asdirected by EIC

Provn of lightening proctection complete all as directed by EIC

M&L for Point wiring (Concealed)/Surface using approved colour coding as per IS Red/Yellow/Blue, Black and green for single phase circuits) with multi stranded copper conductor 1.5 Sqmm nominal cross area single core PVC insulated and unsheathed FR LSH cable 1100 Volts grade ISI 694 marked with valid CML No. in and including medium grade PVC concealed conduit of dia not less than 20mm and conduit accessories ISI marked with valid CML No. ( IS 9537 -1983 for wall/roof /floor etc with pressed flush metal boxes covered with inner plates & outer plates etc suitable for mounting of Modular switches & sockets/Surface Board including PVC insulated multi stranded copper conductor FRLSH 1.5 sqmm nominal cross sectional area single core FRLSH cable as earth continully conductor to commonearth and connecting to earrth dolly complete all as specified and directed for One socket outlet 3 pin, 5 Amps on independent board, controlled by one No 5 Amp switch.

S&F Modular switch flush type single pole one way 6 Amp ISI Marked.

S&F Modular socket outlet 2 in 1, 5 pin, 6 Amp, 230 Volts flush type .

S&F sheet metal enclosures 415 volt TPN 4 way with 200 Amp rated bus bar, double door IP-43 DB's suitable for With one No 100 Amp 10 KA TPN MCB as incoming complete all as specified and directed by Engr-in-charge.

Supply and Fix MCB TPN 63 to 100 Amps ISI marked.

Supply and Fix ELCB 3 phase 63 Amps 4P,30 MA capacity

M&L for chemical earthing complete with copper earth plate elctrodes 90cmx60cmx5mm thick and 20x3 mm copper strip as earthing lead buried directly in ground (Preferably in veritical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 3 meter (BGL) connected to Copper strip of size 32x6 mm earth lead by means of bolts, nuts, check nut and washer of copper including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore "medium grade" galvanized iron water tubing fixed with case iron funnel and wire mesh and 25 mm bore "light grade" galvanized iron protection pipe for earth lead copper strip upto 5m length charcoal, common salt, complete all as shown in EP No 3 of SSR 2009 Part-I, connected to test point complete, all as specified and testing on comletion.

Supply, laying testing in trenches/on Wall LT UG XLPE insulated,armoured, heavy duty electric cable, aluminium coductor, 1100 V grade,croos sectional area 35 sqmm 3.5 core complete all as specified and directed by Engr-in-charge.

Supply and fix GI tubing medium grade of 40 mm dia for cable protection complete all as specified and directed by Engr-in-charge.

M/s Dhapola Elevator and Engineering (BID ID -3280800)