ReConstruction of Community Toilet at Pakkali Street at ward No.51

Dismantling the existing damaged RCC including clearing away from site etc complete as directed by the departmental officers.

Dismantling the existing damaged brick masonry including clearing away from site etc complete as directed by the departmental officers.

Earthwork excavation for foundation by manual means for Isolated,Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering,bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10mts and initial lift of 2.00mts and clearing and levelling the site etc complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation,basement etc with filling crushed stone sand in layers of not more than 15cm thick well watered,rammed and consolidated etc complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:5:10 (One Cement,Five crushed stone sand and Ten hard brocken stone jelly) using 40mm gauge hard brocken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15cm thick well rammed,consolidated and including curing etc complete complying with standard specification and as directed by the departmental officers. -Mixing by manual means

Brickwork in following Cement Mortar using best quality Fly ash Brick of size 230x110x75mm with class designation of 7.5 conforming to IS 13757-1993 or IS 12894-2002 for foundation and basement including Cost of Mortar Plasticizer, curing,etc complete complying with standard specification and as directed by the departmental officers.Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

Basement

Ground Floor

Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40x40x5mm and supported by Steel Adjustable Telescopic Props of Size 2x2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) etc complete in all floors complying with standard specifcation.Steel Adjustable telescopic props shall be provided as directed by the departmental Officers.(Payment for centering shall be given after the concrete is laid).

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings,column pedestals,plinth beams,grade beams,staircase steps,Sill slabs etc which require only nominal strutting using mild steel sheets of size 90x60cm and 10 BG stiffened with welded mild steel angles of size 25x25x3mm for boarding,laid with silver oak joists of size 10x5cm & 7.5x5cm as support runner,vertical stiffener,side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc complete in all floors complying with standard specifcation.(Payment for centering shall be given after the concrete is laid).

Supplying and erecting centering for plane surfaces such as RCC Floor/Roof Beam,Lintels,Cantilever Beams,Bed Blocks etc with necessary supports and strutting upto 3.60m height in all floors with all cross bracings using MS Sheets made of 10 gauge thick welded with MS angle of Size 25x25x3mm for boarding laid over Steel adjustable Span of Size 2x2m(expandable upto 3.60m) and Silver Oak Joists of Size 10x5cm spaced at 50 to 60cm c/c and supported by Steel Adjustable Telescopic Props of Size 2x2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick) Spaced at not more than 50 to 60cm c/c,etc complete complying with standard specifications.Steel adjustable span and Steel Adjustable telescopic props shall be provided as directed by the departmental Officers.(Payment for centering shall be given after the concrete is laid).

Supplying,fabricating and placing in position Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500,Fe550D,Fe 500D etc for all RCC works as per design given including cost of steel reinforcement and GI binding wire,wastage etc complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Basement

Reinforced Cement Concrete 1:1-1/2:3 (One Cement,One and Half crushed stone sand and Three hard brocken stone jelly) using 20mm gauge hard brocken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges,centering and shuttering but including Super Plasticiser,mixing charges for machine mix,laying,vibrating with mechanical vibrators,finishing,curing,etc and providing fixtures like fan clamps in the RCC floor/roof slabs wherever necessary and bearing surfaces of walls,beams etc shall be finished smooth with Cement Mortar 1:3 (One Cement and Three Sand) and kraft paper laid over it without claiming extra,etc complete complying with standard specification and as directed by the departmental officers - machine mix

Basement

Supplying and fixing Mild Steel grills for windows,ventilators etc complete complying with standard specifications and as directed by the departmental officers.

Supplying and fixing inpositon Indian Water Closet (Oriya type) of size 580x440mm white glazed earthern ware of approved quality and brand with “P” or “S” trap conforming to BIS with crushed stone sand cushion and forming flooring alround the closet using 40mm brocken brick jelly in lime concrete 1:2:5 (One lime,Two crushed stone sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall/reinforced cement concrete roof/floor slab and making good the dismantled portion to the original condition with leakages etc complete complying with standard specifications and as directed by the departmental officers.(The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing inposition white/colour glazed European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia/PVC pipe of 110 mm dia,double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement,cement for packing,spun yarn,teak wood plugs,brass screws,etc including supplying and fixing 10litres capacity PVC/12.5litres capacity porcelin low level flushing tank with a pair of CI brackets,etc complete with all fittings such as 15mm brass ball valve with polythene float with brass handle,union,coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections,15mm GM wheel valve,15mm brass nipple (2Nos),15mm nylon connection,TW plugs,screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer,dismantling the masonry and re-doing the dismantled masonry to original condition etc complete complying with standard specifications.(The EWC and flushing tank with all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing inposition best quality and approved make Indian made white/colour glazed earthernware wash hand basin of size 550x400mm (with pedestal/without pedestal) with a pair of cast iron brackets,including cost 15mm dia brass CP pillar tap,32mm dia “B” class GI waste pipe with rubber plug and chain,15mm dia GM wheel valve,15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall inposition with TW plugs and screws,rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying,laying and jointing UPVC pipes of Class 5 (having working pressure of 10kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs,PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portio to original condition with necessary brick work/cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level,etc complete complying with standard specifications.The PVC pipes shall be got approved by Executive Engineer before use on works -External water supply above ground level

25mm dia UPVC pipe above GL

25mm dia UPVC Union

25mm dia UPVC elbow

25mm dia UPVC tee

25mm dia GM Gate valve

25mm dia UPVC coupling

20mm dia UPVC pipe above GL

20mm dia UPVC elbow

20mm dia UPVC tee

20mm dia UPVC coupling

25x20mm UPVC Reduer

CP Two Way Bib Cock with Health Faucet

UPVC Solvent

PVC tank

Supplying and fixing inposition 15mm dia brass CP screw down tap/Pillar tap/Swan neck tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread,etc complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works)15mm dia brass CP screw down tap

Supplying and fixing inposition best quality PVC soil/waste pipes of various dia having 6kg/ sq.cm pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC/MS clamp,teak wood plugs,brass screws,etc and making connection to all sanitary fittings,dismantling masonry/RCC works wherever found necessary and making the good dismantled portion to the original condition,including testing for any leakages,etc complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works).The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

110mm dia PVC pipe 6KSC

Supplying and fixing inposition PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks,dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works)

110mm dia PVC Tee

110mm dia PVC Elbow

110mm dia PVC Coupler

Solvent cement

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation,CC 1:5:10 of 10cm thick and brick work in Cement Mortar 1:5 [One cement and Five M sand] using best quality of Clay burnt Bricks of size 9”x43/8”x23/4” with Class designation of 7.5 and Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement,Three crushed stone sand and Six Aggregate] 15cm thick and covered with precast slab 5cm thick etc complete complying as directed by the departmental officers as per standard specification.

Manufacturing supplying and fixing of Fully Panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and MS angles of size 35x35x5mm for the shutter frames,stiffeners with 32x6mm MS flat is provided at required intervals in the shutter frame.18-gauge CR sheet laid as panel in the shutter and welded intact MS flat 18x5mm is welded over the 32x6mm MS flat sandwitching the CR sheet in between additional stiffeners with 18x5mm MS flat is provided diagonally at the rear side of the shutter.3nos of Steel Parliament Hinges of Size 12x150mm in case of single leaf and 6nos of Steel Parliament Hinges of Size 125x150mm in double leaves shutter to be provided 6nos of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door.Tower bolts 3nos,one at the top,one at lock rail(Inner) and the other at the bottom are provided 1no.Aldrop is provided at lock rail section in the door 2Nos of 200mm handle are to be provided.One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place.Incase of double leaf door MS Flat 32x3mm at 1.1Kg/m is provided on the one shutter conceal the gap between the two shutters at an appropriate place in the door.A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing.All members are given a coat of red oxide primer as directed by the departmental officers.The rate includes cost of all materials,labour charges,transportation to site of work, loading, un loading and all other incidental charges etc complete complying with standard specification and as directed by the departmental officers. -Single leaf

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs,beams,sunshades,facia,canopy slab,staircase waist slab, landing slab etc with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used, hacking the surfaces and curing,etc in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand),12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used,curing etc complete complying with standard specification and as directed by the departmental Officers.

Flooring with ceramic tiles of following size and variety conforming to IS 15622 laid over cement mortar bed of 20mm thick in cement mortar 1:3 (One Cement and Three crushed stone Sand) with required Cement Slurry and Mortar Plasticizer including cutting the tiles to the required size with special cutter wherever necessary,laying inposition and pointing with Water Resistant Tile Epoxy Grout at the rate of 0.27Kg/sq.m etc complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)a.Self Designed Colour Ceramic Tiles of size 305x305x6mm

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand),20 mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used,curing etc complete complying with standard specification and as directed by th departmental officers.

Dadooing walls with following best approved quality,white/colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27Kg/sq.m neatly in all floors,curing,etc complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)Dadooing with white glazed tiles of size 150x150x6mm

Wiring with 2x1.5sq.mm (22/0.3) PVC insulated unsheathed SC Cu Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessoires with TW switch box and 5A FT switch in flush with wall with 3mm thick hylum sheet cover for making good of the concealed portion with suitable colour for PVC concealed light point/fan point (For electronic regulator)(SD-24)

Wiring with 2x1.5 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150x100x113mm TW switch box with 3mm thick hylem sheet cover for 5A 3pin non inter locking wall socket with 5A flush type switch with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for concealed PVC plug point ( SD-38)

Wiring with 2x4 sq.mm PVC insulated SC unsheathed FRLS copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories in flush with wall with 150x100x113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non inter locking wall socket with 15A flush type switch with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour for concealed power plug point (SD.No.40)

supply and run of 2 of 1.5sq.mm PVC insulated SC unsheathed FRLS copper Conductor of 1100V grade on 7/20 GI bearer wire for service connection mains ( SD - 64)

Supply and fixing of bulk head fitting 15 W LED-SD -83

Supplying and fixing inposition best approved of BIS quality PVC rain water down fall pipes having a pressure of 4kg/sq.cm including cost of necessary PVC shoe,PVC bend,cast iron gratings of required diameter and special clamps,brass screws,nails,etc and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc complete. The rate shall be inclusive of cast of removable cast iron grating.The PVC pipe shall be fixed in wall with special type of “U” clamp at the centre of the pipe line in addition to those for more than 3metre pipe length,etc complete complying with standard specification and as directed by the departmental officers

Supplying and fixing inposition Indian make bevelled edge mirror of approved quality and brand PVC/Fibre Glass framed 5.5mm thick mirror of followingsize,Shelf type with hard board backing of approved colour fixed with brass screws,rawl plug,etc complete complying with standard specification.(The mirror should be got approved by the Executive Engineer before use on woks

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws,etc complete complying with standard specifications.(The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150x100mm including cost of teak wood plugs,brass screws,etc complete complying with standard specifications.(The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing fine polished cuddapah slab of following thickness for cup- board arrangements including laying to correct alignment with necessary cement mortar and black powder etc,complete complying with standard specification and as directed by the departmental officers

Supplying and fixing of vinyle name board of size with corporation embalom and lettering as Tiruchirappalli City corporation,in Tamil as directed by the departmental officers including framed with 50x25mm country wood reepers outer finished with 1”x1” Aluminium beeding with all material and labour cost for fixing etc complete.

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum,brushes,scaffolding charges,etc complete complying with standard specification and as directed.

Painting New Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over one coat priming coat in all floors including the cost of primer etc complete complying with standard specification and as directed by the departmental officers.(The make,quality and colour of paint should be got approved by the Executive Engineer before use on works)

Painting new iron works such as steel doors,windows,ventilators,window bars,balustrades etc with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc complete complying with standard specification and as directed by the departmental officers.(The make,quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12 mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used,curing etc., complete complying with standard specification and as directed by the departmental officers.