PROVISION OF COVERED SHED TO CERTAIN HOUSES OF NORA KATARIBAGH AND OTHER SANCTIONED WORK OF AGE B and R III UNDER GE NW NAVAL BASE KOCHI

Amount

Excavation in post holes (or similar holes) each not exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil complete all as specified

M&L for plain cement concrete ( 1:3:6) type C 2 using 40 mm graded stone aggregate for foundations, filling and mass concrete, complete all as specified and as directed

M & L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.11611979 grade St.-240 complete all as specified

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, ridge/valley etc, fixed with self tapping screws as complete all as specified .

M&L for preparation on new steel surface of any description over 10 cm width or girth and applying two coats of anti corrosive paint over a coat of suitable primer complete all as specified .

M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified .

M&L for18mm thick Multiwood modular kitchen cabinets, inside depth not less than 0.50M , water proof, termite & Borer proof, corrosion free with melamine polished shutter and auto closer counter sunk hinges, stainless steel handles complete all as directed . ( Note :(i) Only front facing area of cabinet will be measured for payment. (ii) Stainless steel baskets mentioned as supply only under Sl. item No.8 shall be fixed under this item as the unit rate quoted against this item is inclusive of this fixing provision) all as specified and as directed .

Supply only a set of stainless steel baskets with fittings as in modular kitchen cabinet as per following details :- (i) Plate basket 21"x19"x8" - 01 No (ii) Plane basket 21"x19"x8" - 01 No. (iii) Plane basket 17"x19"x8" - 01 No. (iv) Butlery basket 17"x19"x4" - 01 No. (v) Cup & Saucer basket 17"x19"x4" - 01 No. (vi) Single pull out 8" - 01 No. (vii) GT- PT & Drip tray 22" - 01 No. (viii) Telescopic channels of appropriate size - 06 Nos. ( Make : First quality of Sleek/ Ebco/ Dolin) all as specified and as directed .

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc,complete all as specified and as directed .

M&L for 15 mm thick screed bed or bedding layer or mortar in CM (1: 6 ) for laying in floor finishes all as specified and directed .

M&L for rendering 10mm thick cement plaster in cement mortar (1:4) on brick work or concrete surfaces finished rough to receive wall tiles complete all as specified and as directed.

M&L for light shade vitrified ceramic tiles, 10 mm thick (square / rectangular), polished, area of each tile not exc 0.36 sqm, laid in floors etc. set & jointed in neat cement slurry & pointed in white or coloured cement to match complete all as specified and as directed .

All as per item No 12 above but as in vertical surface complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry or PCC block masonry built in cement mortar including all quoins,pillars etc excluding ashlar facing,dressed stone work and pre cast concrete articles and pre cast concrete block walling complete all as specified and as directed .

Dismantling floor hearth or wall tiling including cement mortar bedding removing serviceable tiles to store & rubbish off the premises complete all as specified.

M&L for 1 st class hard wood plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified

M&L for 40 mm thick 1st class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats all as specified

S & F 1st class hard wood plain 30 mm thick glazed skeleton shutters, open rebated and prepared to receive glass, guaze etc, (without sash bars), edges of framing plain, chamfered or rounded fitted with cut, and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a) complete all as specified

S&F Butt Hinge 100mm in size, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11 and fixed, complete all as specified and as directed.

S&F 150 mm long Brass handles, cast type, polished bright complete all as specified and as directed.

S&F 200 mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed.

S&F 200 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed.

S&F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and as directed.

M&L for mild steel flat iron of size 25 mmx 3 mm as in hold fasts for fixing door frame et cand similar small articles conforming to Fe-290 Gde-E-165 complete all as specified

M&L for plain cement concrete in 1:2:4 type B-1 using 20 mm graded stone aggregate for embedding hold fast etc including necessary form work complete all as specified

M&L for pre-cast cement concrete block masonry 1:2:4 Type B1, using 20mm graded aggregate with solid blocks, exc 10 cm in width and setting in cement mortar 1:4 complete all as specified and as directed .

M&L for rendering 15 mm thick cement plaster in cement mortar (1:6) on brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and as directed.

M&L for rendering 15 mm thick cement plaster in cement mortar (1:4) on brick work or concrete surfaces finished even and smooth with out using extra cement complete all as specified and as directed.

M&L preparing new and old decorated surfaces of wall and applying 3 mm thick wall care putty and two coats of acrlylic interior emulsion over a coat of primer complete all as specified and as directed.

M&L preparing new and old decorated surfaces of wall and applying two coats of Apex ultima protek top coat over a coat of protk base coat complete all as specified and as directed.

M&L for Virified Ceramic coloured tiles double charged/ultra charged 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match,fixing the tiles with chemicals on the existing floor complete all as specified and as directed.

M&L for Virified Ceramic coloured tiles 10 mm thick (square/ rectangular) polished, in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

S&F 10 mm thick tinted sheet glass fixed to aluminium or wooden frame work using necessary beadings etc exc 0.50 Sqm in each pane complete all as specified and directed

S & F sun control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers

Taking down chowkats or frames with shutters (without taking off shutters from frames) exc 1.50 sq. m but not exc 4 Sqm each all as specified

Taking down chowkats or frames with shutters (without taking off shutters from frames) n exc 1.50 sq. m each all as specified

S&F anodised aluminium sliding window and ventilator frame double shutter (glass and wir mesh) with out sash bar,including all necessary jointing cleats,hold fasts,hinges with fixing clips,rubber gasket,anodised snap beading,anodised aluminium fittingsuch as 'F' chanel if required for wire mesh or aluminium grill,handle,locking arrangement etc . Section used for sliding window and ventilator frame and shutter as follows (1) catlogue No 4087 of size 92.36x29.70x1.20mm= 3 track bottom. (2) catlogue No 4099 of size 92.36x29.70x1.20mm= 3 track Side & Top (3) catlogue No 9395 of size 39.00x20.00x1.10 mm= shutter vertical. (4)catlogue No 3994of size 41.00x20.00x1.20 mm - shuttedr top & bottam (5)catlogue No 9779 of size 39.00x20.00x1.60mm= shutter vertical inter lock, of Hindalco or equivalent make as approved by GE complete all as specified and as directed.

S&F aluminium anodised grill having mesh size 50 mmx50 mm made out of 6 mm wde 3 mm thick aluminium section including U chanel,fixing with screws etc complete all as specified and as directed .

S&F 5 mm thick plain sheet glass ordinary quality fixed to aluminium or wooden frame work using necessary beadings etc n.exc 0.50 Sqm in each pane complete all as specified and as directed .

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and as directed .

S&F anodised aluminium door frame with out sash bar,including all necessary jointing cleats,hold fasts,hinges with fixing clips,rubber gasket,anodised snap beading,anodised aluminium fittingsuch as handle,locking arrangement etc . Section used as follows (1) catlogue No 9223 of size 63.50x38.10x2.00 mm= Vertical and horizotal (2) catlogue No 9258 of size 50x44.50x1.80 mm= Door vertical (3) catlogue No 9286 of size 50x45x1.50 mm= Door top &middle (4)catlogue No9246 of size 100x44x1.85 mm - Door bottom . of Hindalco or equivalent make as approved by GE complete all as specified and as directed.

S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty all as specified

S&F interlocking aluminium alloy anodized snap grid for ceiling consists of main Tee runners of size 38mm x 25mm x 1.5mm spaced 1200mm centre to centre and cross Tee of size 25mm x 25mm x 1.5mm, 1200mm long spaced between the main Tee at 600mm centre to centre to form a grid of 1200mm x 600mm and provide a secondary cross Tee 25mm x 25mm x 1.4mm (of length 600mm) to be interlocked of the centre of 1200mm x 600mm panel to form a grid of 600mm x 600mm and wall angle 32mm x 32mm x 1.5mm. Aluminium alloy extruded section shall be aluminium anodized (minimum 15 micron) and shall conform to IS-733, IS-1285 and IS-737 complete all as specified and as directed.

M&L for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed.

M&L for 4mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws all as specified and as directed.

S&F stainless steel of Grade 304, hollow section letters(in English and Hindi) made out of stain less steel sheets of size 300mm height, width 25mm , 2.00 mm thick fixed as per manufacturer's instructions or as directed.

M & L for preparation of old Mangalore Patten roof tiles surface including cornices of roof and chequered tiles in floor and applying one coat of weather proof (antifungal) paint complete all as specified

Dismantling of Wall or ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets etc , keep in safe custody for reuse complete all as specified and directed.

M&L Reinforced Cement Concrete type B1 1:2:4 (using 20 mm graded aggregate) as in stair case complete all as specified and directed.

M & L formwork to staircases with sloping or stepped soffits including risers and stringers for rough finished surface of concrete all as specified

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with andincluding mild steel wire (annealed) not less than 0.9mm dia or securing with clip all as specified and directed .

All as per item No 51 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, helical stirrups, spacers and binders

M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms, wash hand basin counter and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed

M&L for 18 to 20 mm thick Granite (of any type) work (table rubbed and polished) for wall lining ) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite completeall as specified and directed

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for

STANDARD ENGINEERING

ANIE JOHN CONTRACTORS

Albert Rebello and Company

M/s Antony Kallarakkal

MS BUILDERS

Oriental Constructions