Building Works

Name of Work :: Construction of New Mamlatdar office (Rural) and Mamlatdar office (City) at Nadiad, Dist. Kheda

Bill of Quantities (BOQ)

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[1] Excavation for foundation upto 1.5 m depth including sorting out 2389.00 Cum 117.08

and stacking of useful materials and disposing off the excavated

stuff upto 50 Meter lead.(A) Loose or soft soil

[2] Excavation for foundation for depth from 1.5 m to 3.0 m including 1233.00 Cum 162.38

sorting out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead.(B) Dense or Hard soil

[3] Excavation for foundation for depth from 3.0 m to 5.0 m including 383.00 Cum 285.73

sorting out and stacking of useful materials and disposing of the

excavated stuff upto 50 Meter lead.(C) Hard Murrum

[4] Filling available excavated earth (excluding rock) in trenches. 2660.00 Cum 130.39

plinth, sides of foundations etc. in layers not exceeding 20 cm. in

depth consolidating each disposited layer by ramming and

[5] Filling in foundation and plinth with murrum or selected soil in 211.00 Cum 282.02

layers of 20cm. thickness including watering, ramming and

consolidating etc. complete.

[6] Filling in plinth with sand under floors including watering ramming, 164.00 Cum 460.18

consolidating and dressing complete

[7] Applying general insecticide pest control treatment to floors, 1243.00 Sqm 89.28

cupboards etc including labour materials etc. complete. Using

Imidacloprid 30.5 SCas Per IS 6313 part -II( (0.075% concentration

by mass) is recommended 10.5ml chemical diluted with 5 liters of

water application 0.5 litre chemical /Sqm of surface is

recommended as per I.S.

[8] Providing, laying, spreading and compacting graded stone 97.00 Cum 1103.11

aggregate to Wet Mix Macadam (WMM) including Spreading the

stone aggregate for rolling including filling the interstices to

required camber and gradient etc. complete as per instruction of

Engineer In Charge.

[9] Providing and laying controlled cement concrete M.150 for curing 152.00 Cum 3860.16

complete excluding cost of formwork and reinforcement for

reinforced concrete work in (A) Foundations, footings,Base of

columns and Mass concrete

[10] Providing and laying controlled C.C.M.250 & curing complete 387.00 Cum 4502.04

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in foundation,

footing bases of columns and the like and mass concrete

[11] Providing and laying controlled C.C. M.250 & curing complete 65.00 Cum 7604.02

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work including all .in

Columns upto Plinth

[12] Providing and laying controlled cement concrete M-250 and curing 246.00 Cum 5800.73

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Plinth BEAMS / Tie

[13] Providing and laying cement concrete 1:3:6 ( 1 cement: 3 coarse 445.00 Cum 3172.71

sand: 6 crushed stone aggregate 40 mm nominal size ) and curing

complete excluding cost of form work & including all in foundation

[14] Providing and laying controlled cement concrete M.150 for curing 154.00 Cum 3860.15

complete excluding cost of formwork and reinforcement for

reinforced concrete work in Plinth slab

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[15] Providing and laying controlled C.C. M.200 & curing complete 177.00 Cum 7629.38

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Columns upto all

[16] Providing and laying controlled cement concrete M.200 and curing 386.00 Cum 6152.84

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in Beams upto

all floor level

[17] Providing and laying controlled cement concrete M.200 and curing 49.00 Cum 7526.42

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in Lintel /

Coping upto all floor level

[18] Providing and laying controlled cement concrete M.200 and curing 24.00 Cum 8148.96

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in CHHAJJA

including finishing coat CM (1:3) for chhajja plaster upto all floor

[19] Providing and laying controlled cement concrete M.200 and curing 494.00 Cum 6208.05

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in SLAB upto all

[20] Providing and laying controlled cement concrete M.200 and curing 20.00 Cum 6711.24

complete including the cost of formwork but excluding the cost of

reinforcement for reinforced concrete work in Staircase upto all

[21] Providing and laying controlled cement concrete M.200 and curing 60.00 Cum 8818.43

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in RCC Wall

[22] Providing and fixing premoulded compressible filler board in black 68.00 Sqm 1324.37

colour confirming to MoRT&H Specifications (Clause 1015), having

minimum density 95kg/cum. non-staining with less than 1% water

absorption & compression recovery of 93% minimum as per

specification for 40 mm wide expansion joint including cutting to

required size and shape at all levels etc.complete as directed.

[23] Providing and applying the elastomeric joint sealant two 678.00 Rmt 255.60

component, high performance polysulfide formulation conforming

to BS:4254 and ASTM C 920 having weathering resistance to ultra-

violet rays and shall exhibit shore A hardness of 25 and have

movement accommodation factor 25% including using of

compatible primer of approved standard etc. complete. For 20 mm

[24] Providing TMT Bar FE 500D reinforcement for R.C.C. work including 247030.00 Kg 78.21

bending, binding and placing in position complete upto all floor

[25] Brick work using common burnt clay building bricks having 284.00 Cum 4021.02

crushing strength not less than 35 kg./Sq.Cm. in foundation and

plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)(B)

[26] Brick work using common burnt clay building bricks having 540.00 Cum 4369.70

crushing strength not less than 35 kg./Sq.Cm. in Super Structure

superstructure above plinth level in Cement Mortar 1:6 (1-

Cement : 6 -fine sand) (B) Conventional upto all floor level

[27] Half brick masonry in common brunt clay building bricks having 1528.00 Sqm 650.16

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:5

(1- Cement : 5 -coarse sand ) in superstructure above plinth level

(B) Conventional upto all floor

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[28] Providing and laying cement concrete 1:4:8 (1- Cement : 4- Coarse 31.00 Cum 2658.40

sand : 8- Graded Brick bats aggregate 40mm normal size) and

curing complete excluding cost of formwork in Sunk Filling

[29] Providing and fixing G.I. hexagonal chickenmesh of size 20mm x 1110.00 Sqm 178.45

20mm of 24 gauge at junction of concrete and brick work or

between different materials after making "V" grove between two

different material surface and filled with rich cement mortar and

@ 100mm on each side of surfaces including necessary "U" nails /

screws / washers with cleats for fixing, overlaps, scaffolding at all

floors / all levels / all heights / all shapes etc. complete as per

drawing / specifications and direction of Engineer-in-charge.

[30] Providing and fixing 38 mm thick single shutter solid core wooden 133.00 Sqm 4909.14

flush shutter confirming to IS:2202 & ISI approved manufacturer

finished with 1 mm thick Laminate on both side of shutter, 6 mm

thick polished teak wood beading on periphery with anodized

aluminium section frame (frame size 38mmx 63.5 mm.) equivalent

to jindal door section no 19552 -weight not less than 1.1 kg/mt

with wooden inserts for durable grip of door hinges with 150mm-

200mm S.S.Handles and S.S.Fixtures & locking arrangement on

each shutter, fixed with 4 nos. 150mm high S.S.Hinges , SS Tower

Bolt, magnetic door catcher etc. complete as directed by Engineer

[31] Providing and fixing double shutter entrance door with heavy duty 35.00 Sqm 4430.17

floor spring and pivoted shutter made from teakwood 5 cm x

cm. styles and 6 nos. 5 cms. X 5 cms. teakwood rails covered with

mm thick water proof ply finished with both sides 1 mm thick

laminates ( colour and shade to be approved by architect ) with

anodized aluminium section frame equivalent to jindal door

section weight not less than 1.79 kg/mt with wooden inserts for

durable grip of door hinges with 600 mm long S.S.Handles on both

shutter and S.S.Fixtures & heavy duty mortise locking arrangement

on each shutter, SS Tower Bolt etc. complete as directed by

Engineer In Charge.

[32] Providing and fixing single shutter FRP frame size 100x50 mm and 32.00 Sqm 3212.30

35mm thick FRP depress panel shutter having extra reinforcement

on sides & edges in Gel coat finish. The core of the shutter & frame

is to be filed up with injected fire retardant grade polyurethene

foam done in situ alongwith embedded wooden pieces for

stiffening & also taking hinges & fintures. The whole FRP frame &

shutter is to be water proof weather proof, termite proof &

resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges

with necessary screws & alluminium fixtures & fastenings &

fastener sleeve.

[33] Providing and fixing double shutter FRP frame size 100x50 mm and 11.00 Sqm 3600.04

35mm thick FRP depress panel shutter having extra reinforcement

on sides & edges in Gel coat finish. The core of the shutter & frame

is to be filed up with injected fire retardant grade polyurethene

foam done in situ alongwith embedded wooden pieces for

stiffening & also taking hinges & fintures. The whole FRP frame &

shutter is to be water proof weather proof, termite proof &

resistance to mild acid/alkali. Rates are to be inclusive of S.S hinges

with necessary screws & alluminium fixtures & fastenings &

fastener sleeve.

[34] Providing and fixing M.S. grills of required pattern to wooden / 14913.00 Kg 107.36

stone frames of windows etc. with M.S. 16MM DIA. POLISHED

HORIZONTAL BARS at required spacings and frame alround, square

or round bars with round headed bolts and nuts or by screws

including one coat of primer and two coats of matt finished oil

painting etc complete.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[35] Providing and fixing in position collapsible steel shutters with 16.00 q 5825.32

vertical channels 20 x 10 x 2 mm braced with flat iron diagonals

x 5 mm size with top and bottom rails of T_rin 40x 40 x 6 mm with

38mm dia, steel pulleys complete with bolts, nuts, locking

arrangements, stoppers handles including applying a priming coat

of red lead paint.

[36] Providing and fixing TWO TRACK SLIDING WINDOW: Standard 3.00 Sqm 3739.12

extruded colour anodised aluminium section of best quality brand

equivalent to JINDAL series E (30 mm) séction numbers: frame

bottom track 20878, frame top & sides 20877, shutter top & lock

rails 21675, bottom rail 20772, interlock rails 20550 with 5 mm

thick transparent tinted float glass, with rubber gasket, air lock

strip and finishing joints with transparent silicon sealant with

alluminium powder coated fittings and fixtures etc. complete as

per instruction of Engineer In Charge

[37] Providing and fixing THREE TRACK SLIDING WINDOW WITH FIXED 58.00 Sqm 3734.17

GLASS ABOVE : standard extruded color anodized aluminum

section of best quality brand equivalent to jindal series C (20mm)

section numbers: frame bottom track 21651, frame top & sides

21650, shutter top rail 20530, bottom rail 20529, side rails

intérlock rails 20531 with 5mm thick transparent float glass, with

rubber gasket. Air lock strip and finishing joints with transparent

silicon sealant, with aluminum powder coated fittings and fixtures

and fixed glazing above as shown in elevation. etc. complete as per

instruction of Engineer In Charge.

[38] Providing and fixing CASEMENT WINDOW WITH SINGLE SHUTTER 198.00 Sqm 4285.35

FIXED GLASS ABOVE: Alluminium extruded casement window

frame of best quality brand equivalent to Jindal series-B Section

nos. 20558, 20559,20560 & 19391 including 5mm thick transparent

float glass with transparent silicon sealant with aluminum powder

coated fittings and fixtures, and fixed glass at top as per elevation.

etc. complete as per instruction of Engineer In Charge.

[39] Providing and fixing FIXED GLASS WINDOW: Standard extruded 96.00 Sqm 3511.10

colour anodized alluminium section equivalent to JINDAL Frame

no. 20128 and mullion frame no. 20147 with 5mm thick

transparent tinted float glass, with rubber gasket, finishing joints

with transparent silicon sealant, with alluminium powder coated

fittings and fixtures etc. complete as per instruction of Engineer In

[40] Providing and fixing STANDARD EXTRUDED COLOR ANODIZED 12.50 Sqm 4183.81

ALUMINUM FRAME WITH 5MM. THICK BAJARI FIGURED

ADJUSTABLE GLASS LOUVERS OF STD MAKE with lever handle and

four bar hinges for top hung, etc.complete as per instruction of

Engineer in charge.

[41] Providing and fixing FIXED LOUVERS 114 MM WIDE GI SHEET 74.00 Sqm 2393.28

having thickness of 0.55 mm & weight not less than 490 gm/meter,

roll formed to create 84 mm wide louver snap fixed on special

shaped GI channel, fix louvers & channels shall finished with

powder coating of 55 micron as per instruction of Engineer in

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[42] Providing and fixing 18mm to 20 mm THICK MIRROR POLISHED 105.00 Sqm 2559.76

GREEN MARBLE AS APPROVED COLOUR AND SHADE, WITH ALL

EXPOSED EDGES POLISHED, CHAMFERED AND PROJECTED 6MM

FROM FINISHED WALL THICKNESS For Doors frame / WIndows cill

& Jambs Clading as per design incl. full moulded round both edge

on 10 mm thick cement mortar 1:3 (1 -cement : 3 coarse sand )

jointed with grey cement slurry including rubbing and polishing

etc. complete as per instruction of Engineer In Charge.

Fixing: rear face of marble shall be sanded using clean sand sieve

no.10 passed 2mm, fixed with araldite and dried for at least

hours before fixing.

[43] Providing and laying MACHINE CUT MACHINE POLISHED 7.5 CMS. 21.60 Sqm 1660.49

WIDE GREEN MARBLE STONE STRIPS FLOORING over 20mm

(Average) thick base of cement mortar 1:6 (1-cement : 6-coarse

sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with grey cement slurry mixed with pigment to match the

shade of slab including rubbing and polishing etc. complete.

[44] Providing & Laying 10 TO 12 MM THICK READY-MADE FULL BODY 137.00 Sqm 2139.63

VITRIFIED STEPTILES OF 120X30CM (TREAD) 120X15CM (RISER) &

60X60CM ( LANDING) WITH HALF ROUND NOSING, ANTI-SKID

FLUTES IN PLACE. 7.5CM SKIRTING OF THE SAME AS APPROVED BY

ARCHITECT OFFICE FOR STAIRCASE on 10 mm thick cement

mortar 1:3 (1 -cement : 3 coarse sand ) jointed with grey cement

slurry including rubbing and polishing etc. complete as per

instruction of Engineer In Charge.

[45] Providing & Laying 600 X 600 X 10 MM THICK SOLUBLE SALT 2682.00 Sqm 1248.74

VITRIFIED TILES FLOORING WITH PATTERN COLOUR & SHADE

AS/DETAIL APPROVED BY ARCHITECT. (10% DARK COLOUR TILES

FOR PATTERN) over 20 mm (average) base of cement mortar 1:6 (

1 cement: 6 coarse sand) on new surface or fixing on existing

flooring by adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including finised with

flush pointing & cleaning the surface etc. complete

[46] Providing and laying 600 X 600 X 10 MM THICK SOLUBLE SALT 121.00 Sqm 1141.45

VITRIFIED TILES 7.5 CM. SKIRTING WITH PATTERN COLOUR &

SHADE AS/DETAIL APPROVED BY ARCHITECT. (10% DARK COLOUR

TILES FOR PATTERN) in skrting risers of steps and dedo on 10mm

thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed

with white cement slurry etc. complete as per instruction of

Engineer In Charge.

[47] Providing and fixing 18mm to 20 mm THICK MACHINE CUT FREE 24.00 Sqm 2639.91

EDGES, MACHINE POLISHED GREEN MARBLE FINISHED TREAD &

RISER IN SINGLE PIECE IN STEPS with antiskid two groove line 5 x

2.5 mm as per design incl. full moulded round both edge on

mm thick cement mortar 1:3 (1 -cement : 3 coarse sand ) jointed

with grey cement slurry including rubbing and polishing etc.

complete as per instruction of Engineer In Charge.

Fixing: rear face of marble shall be sanded using clean sand sieve

no.10 passed 2mm, fixed with araldite and dried for at least

hours before fixing.

[48] Providing and laying 18mm to 20 mm THICK MACHINE CUT FREE 53.00 Sqm 1559.49

EDGES, MACHINE POLISHED GREEN MARBLE FLOORING over

20mm (Average) thick base of cement mortar 1:6 (1-cement : 6-

coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid

over and jointed with grey cement slurry mixed with pigment to

match the shade of slab including rubbing and polishing etc.

[49] Providing & filling 3-4 mm wide groove filled with Epoxy grout of 7126.00 Rmt 96.17

best quality Brand as directed by Engineer In Charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[50] Providing and laying 600 X 600 X 10 MM THICK MATT ANTISKID 1018.00 Sqm 908.32

PORCELENE TILES FLOORING AS PER DETAILS & SELECTION in

flooring treads of steps and landing laid on a bed of 12mm thick

cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush

pointing in white cement.

[51] Providing and laying 300 X 600 X 10 MM THICK PREMIUM PRINTED 707.00 Sqm 1596.05

GLAZED TILES DADO FULL HEIGHT in skrting risers of steps and

dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse

sand) and jointed with white cement slurry

[52] Providing and laying 300 X 300 X 10 MM THICK MATT FINISHED 73.00 Sqm 949.68

ANTISKID CERAMIC TILES FLOORING AS PER DETAILS & SELECTION

in flooring treads of steps and landing laid on a bed of 12mm thick

cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush

pointing in white cement.

[53] Providing and fixing pre-cast Rubber Dye / steel Dye inter locking 943.00 Sqm 686.90

concrete Concrete Paver block ( Sample to be approved by

architect ) 60mm thick with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per approved design

Confirming to IS 15658 : 2006 including 35 mm Sand layer for

levelling and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

[54] Providing and fixing pre-cast concrete kerb stone of gray cement 453.00 Rmt 384.96

based concrete block 30cm length,30cm height and 15cm thick of

M200 grade concret as per approved design and including

excavation for fixing in proper line and level,filling the joint with

C:M 1:3 (1cement:3fine sand) etc complete.

[55] Providing 15 MM THICK SMOOTH CEMENT PLASTER IN SINGLE 8460.00 Sqm 239.58

COAT WITH 1 x 1 CM GROOVES AT JUNCTION OF STRUCTURAL

MEMBERS on Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) upto all Floor

[56] Providing 10 MM THICK SMOOTH CEMENT PLASTER IN SINGLE 3528.00 Sqm 214.76

COAT WITH 1 x 1 CM GROOVES AT JUNCTION OF STRUCTURAL

MEMBERS on brick/concrete walls for interior plastering upto floor

two level and finished even and smooth in (i)Cement mortar 1:3 (1-

cement:3-sand) for plastering on ceilings and sofits of stairs upto

all Floor Level

[57] 20mm THICK DOUBLE COAT SAND FACED CEMENT PLASTER WITH 2941.00 Sqm 361.59

GUTKA FINISH WITH 1 CM X 1 CM DEEP GROOVES AS PER

ELEVATIONS ( SAMPLES TO BE APPROVED BY ARCHITECTS ) on

walls upto height 10 metres above ground level consisting of

12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm

thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete

upto all floor level.

[58] Applying two coats of putty & two coats of water based primer of 12936.00 Sqm 40.59

approved brand and manufacture on new wall surface to give an

even shade including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand papered

[59] Wall painting (three coats) with plastic emulsion paint (shade and 8743.00 Sqm 119.42

colour to approved by chief architect office,gandhinagar )of

approved brand and manufacture on undecorated wall surface to

give an even shade including throughly brushing the surface free

from mortar droppings and other foreign matter and sand

papered smooth.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[60] Wall painting (three coats) with plastic emulsion paint (shade and 3713.00 Sqm 124.68

colour to approved by chief architect office,gandhinagar )of

approved brand and manufacture on undecorated wall surface to

give an even shade including throughly brushing the surface free

from mortar droppings and other foreign matter and sand

papered smooth.

for painting on ceilings and sloping roofs.

[61] Painting three coats (including priming coat) on new wood and 18.00 Sqm 128.38

wood based surface with enamel paint, interior to give an even

shade including cleaning the surface of all dirt, dust and other

foreign matter sand papering and stopping.

[62] Wall painting (three coats) with plastic emulsion paint IN SPECIAL 230.00 Sqm 249.18

EFFECT (ROYAL PLAY) (shade and colour to approved by chief

architect office,gandhinagar )of approved brand and manufacture

on wall surfaces to give an even shade including thoroughly

brushing the surface free from mortar dropings and other foreign

matter and sand papered smooth

[63] Applying one coat of Exterior Primer of approved brand and 4719.00 Sqm 67.84

manufacture on new wall surface to give an even shade including

thoroughly brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth.

[64] Finishing wall with TWO COATS OF 100% WEATHER PROOF 4719.00 Sqm 114.53

ACRYLIC EMULSION PAINT OF APPROVED SHADE AND BRAND LIKE

APEX (shade and colour to approved by chief architect

office,gandhinagar ) on wall surface (two coats) to give an

required shape even shade after thoroughly brushing the surface

to remove all dirt, and remains of loose powdered materials.etc

[65] Providing cement vata (10cm. x 10 cm. size) quarter round in 454.00 Rmt 23.68

cement mortar 1:1 including neat cement finishing, watering etc.

[66] Providing and laying six courses water proofing treatment with 822.00 Sqm 1060.50

bitumen felt over roofs consisting of first, third and fifth courses of

blown or/and residual bitumen applied hot at 1.45, 1.20 and

kg per square metre of area respectively, second and fourth

courses of roofing felt type 2 grade II (glass fibre base self finished

bitumen felt) and sixth and final course of stone grit 6 mm and

down size or pea sized gravel spread at 6 cubic decimeter per sqm

including preparation of surface but excluding grading, complete.

[67] Providing laying and jointing in true line and level 15mm dia. 230.00 Rmt 72.65

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concealed as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

[68] Providing laying and jointing in true line and level 25mm dia. 445.00 Rmt 91.84

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concealed as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

[69] Providing laying and jointing in true line and level 50mm dia. 660.00 Rmt 195.67

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall

with the help of clamp at every two metre C/C or shall be

concealed as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive

solvent, including cost of all materials.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[70] Providing, laying and jointing in true line and level 110 diametre 575.00 Rmt 835.15

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain

and other end socketed with rubber ring, & fittings conforming to

ISI 14735-1999 of approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size 110 mm

diametre x 149 mm length x 145 mm heigh at every 2000 mm

center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement

including cost of all materials.

[71] Providing, laying and jointing in true line and level 160 diametre 270.00 Rmt 831.22

U.P.V.C (Type B) conforming to IS 13592-1992 with one end plain

and other end socketed with rubber ring, & fittings conforming to

ISI 14735-1999 of approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size 160 mm

diametre x 210 mm length x 196 mm heigh at every 2000 mm

center to center or shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent cement

including cost of all materials.

[72] Providing and fixing concealed center point to wall ceiling & floor 110.00 Rmt 166.86

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings

and clamps including making good the wall, ceiling and floor etc.

complete.[A] 15 mm.

[73] Providing and fixing concealed center point to wall ceiling & floor 160.00 Rmt 249.72

CPVC (SDR 13.5) PIPE having National Sanitation Foundation (NSF)

seal for potable water of following dia. nominal bore tube fittings

and clamps including making good the wall, ceiling and floor etc.

complete. [C] 25 mm.

[74] Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 310.00 Rmt 277.43

working pressure polythene pipes of the following outside Dia.

Low densidy, complete with special falnge compression type

fittings, wall clipsetc. including making good the wall ceiling and

[75] Providing laying (to level or slopes) and jointing reinforced 175.00 Rmt 240.21

concrete Light duty non-pressure pipes I.S. class NP2 of the

following internal diameter with collars and butt ends prepared for

collar joints including testing of joints complete.(B) 150mm

[76] Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 82.00 Each 558.36

mm diameter with jali of the following nominal diameter of self

cleansing design with C.I scread down or hinged grating including

the cost of cutting and making good the walls.

[77] Providing and fixing screw down bib taps of following size.(B) Brass 66.00 No 186.83

chromium plated screws down Bib Tap. (i) 15mm dia.

[78] Providing and Fixing C.P. Pillar cock 15 mm Ø Heavy duty swan 37.00 Each 799.45

neck including fixing with CP brass nipple including all labour &

material etc. complete as per instruction of Engineer In Charge.

[79] Providing and Fixing C.P. Angle stop cock 15 mm Heavy duty with 104.00 Each 558.92

cap including all labour & material etc. complete as per instruction

of Engineer In Charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[80] Providing and fixing wash basin with single hole for pillar tap with 34.00 Each 1653.67

C.I. or M.S. brackets painted white including sutting holes and

making good the same with brass union and CP brass wall

discharge pipe with flanges and cap of best quality brand , Waste

Pipe for Wash basin C.P. 32 mm dia with fittings up to floor trap,

32mm dia CP brass waste coupline with CP chain and rubber plug,

washer and CP brass cap complete in all respects including cutting

and making good the walls RCC work as directed and making good

the same etc. complete.

A) Vitreous China:(ii) Flat Back washbasin 550 mm x v 400mm size.

(i) In white colour.

[81] Providing and fixing WALL HUNG EWC WITH CROFT SOFT CLOSE 13.00 Each 8727.86

SEAT COVER & SNOW WHITE COLOUR-535 X 360 X 335 MM with

integral "P" and "S" trap including jointing the tra best quality

brand including providing and fixing plastic seat cover for wash

down WC with CP brass hinges and rubber buffers back plastic seat

and including providing 12.50 Litres low level flushing cisten with a

"P" air of CI or MS bracket with complete fitting such as lead valve

Sipron 15mm dia brass ball valve with polythene float CP brass

handle, unions and couplings for connection with inlet outlet and

overflow pipes 40mm dia porcelain enamelled flush bend,

including jet spray operated with necessary valve of best quality

brand including cutting holes in walls and making good the same

connecting the flush bend with cistern and closet vitreous china

[82] Providing and fixing water closet squatting Pan (Indian type W.C. 12.00 Each 3303.65

Pan) size 580mm with integral "P" and "S" trap including jointing

the tra best quality brand including providing 12.50 Litres low

level flushing cisten with a "P" air of CI or MS bracket with

complete fitting such as lead valve Sipron 15mm dia brass ball

valve with polythene float CP brass handle, unions and couplings

for connection with inlet outlet and overflow pipes 40mm dia

porcelain enamelled flush bend, including cutting holes in walls

and making good the same connecting the flush bend with cistern

and closet vitreous china etc. complete.

(A) Vitreous China.(I) Long pattern = White colour

[83] Providing and fixing C.P. Brass health faucet with rubbit cleaning 25.00 Each 1173.53

system 1.25 mt. long P.V.C. Flexible tubes and ABS wall hook with

angular stop cock with extension nipple 62 mm long etc. complete.

[84] Providing and fixing Concealed cock 15 mm Ø Heavy duty with cap 37.00 No 675.38

[85] Constructing brick masonry chamber for underground C.I. 37.00 No 2932.93

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with frame

(Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.)

and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of neat cement on

walls and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

[86] Providing and fixing S.W. gully trap with C.I. grating brick masonry 33.00 Each 1292.19

chamber and water tight C.I. cover with frame of 300mm x 300mm

size (inside) with standard weight.(i) Square mouth traps. (A)

100mm x 100mm size P type.

[87] Providing erecting and fixing double coated ISI water tank of 21500.00 litre 3.95

required capacity each with all necessary fittings and connection

etc. complete on terrace

[88] Providing and fixing in position cowel went to pipes.(C) 100mm dia 11.00 No 501.87

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[89] Providing and fixing Urinal of approved quality including 16.00 Each 1541.44

connection with trap and with integral longitudinal flush pipe.(A)

Squating plate pattern white earthenware 550mm x 300mm.

[90] Providing and Fixing 18 mm thick in polished granite shelves / 26.00 Sqm 2008.65

Counter / Partition with extra outer edge 50 mm x 19 mm strip as

per drawing with full round moulded edge resting on wall fix and

jointed with white cement slurry including rubbing, polishing,

labour charges, finishing etc. complete as directed.

[91] Providing and fixing 600mm x 450mm bevelled edge mirrror of 39.00 No 833.73

superior glass mounted on 6mm thick A.C. sheet or plywood sheet

and fixing to wooden pluge with C.P. brass screws and washers.

[92] Providing and fixing Mirror polished GRANITE stone slab 18 mm 61.40 Sqm 3150.36

thick (selected colour and shade) as per design incl. full moulded

round both edge on 10 mm thick cement mortar 1:3 (1 -cement :

coarse sand ) jointed with grey cement slurry including rubbing

and polishing etc. complete as per instruction of Engineer In

[93] Providing and fixing C.P. Towel Ring Square or round shape of 13.00 No 1352.74

Good Quality Brand as directed by Engineer in charge including

fixing as and where directed etc. complete.

[94] Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size 27.00 Each 958.17

having weight not less than 35Kg.

[95] Providing and fixing Heavy Handle valve of aprroved brand & 22.00 Each 440.16

follwing internal dia of Brass including fixing in pipe lines

etc.complete (A) 15 mm Dia

[96] Providing and fixing Heavy Handle valve of aprroved brand & 22.00 Each 510.86

follwing internal dia of Brass including fixing in pipe lines

etc.complete (A) 25 mm Dia

[97] Providing and fixing Heavy Handle valve of aprroved brand & 14.00 Each 682.56

follwing internal dia of Brass including fixing in pipe lines

etc.complete (A) 40 mm Dia

[98] Providing and fixing Butterfly valve of aprroved brand & follwing 19.00 Each 970.41

internal dia of Brass including fixing in pipe lines etc.complete (A)

[99] Providing and fixing stainless steel (Grade 316) railing made of 2205.00 Kg 494.90

Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and

fitting the same with necessary stainless steel nuts and

bolts,brackets etc. complete including fixing the railing with

necessary accessories & stainless steel dash fasteners , stainless

steel bolts etc. of required size, on the top of the floor or the side

of wall with suitable arrangement as per approval of Engineer-in-

charge( for payment purpose only weight of stainless steel

members shall be considered including all fixing accessories such

as nuts, bolts, fasteners etc.) Complete as directed.

[100] Providing & fixing wall mounted SS 304 foldable grab bar of dia. 32 8.00 No 21210.00

mm with anti slip Nylon or equivalent coating , thickness not less

than 1 mm , length of 600 mm of premium quality brand with all

necessary fittings, mounting flange, snap flange,cover,

accessories, labour, connection, transportation etc. complete as

per instruction of Engineer in charge.

[101] Providing & fixing wall mounted SS 304 grab bar of dia. 32 mm 16.00 No 9595.00

with anti slip Nylon or equivalent coating , thickness not less than

1 mm , length of 600 mm of premium quality brand with all

necessary fittings , mounting flange, snap flange,cover,

accessories , labour, connection, transportation etc. complete as

per instruction of Engineer in charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[102] Providing & fixing wall mounted SS 304 grab bar left 90 angle of 4.00 No 15463.10

dia. 32 mm with anti slip Nylon or equivalent coating , thickness

not less than 1 mm , vertical grab bar length not less than 450 mm

& horizontal grab bar length not less than 850 mm both in one

continious piece of premium quality brand with all necessary

fittings , mounting flange, snap flange , cover, accessories , labour,

connection, transportation etc. complete as per instruction of

Engineer in charge.

[103] Providing & fixing wall mounted SS 304 Back Rest Seat with anti 4.00 No 9928.30

slip Nylon or equivalent coating , thickness not less than 1 mm

Size not less than 450 mm of premium quality brand with all

necessary fittings , mounting flange, snap flange , cover,

accessories , labour, connection, transportation etc. complete as

per instruction of Engineer in charge.

[104] Providing and fixing Brailee dote & text sign plate on wall / door 2.00 Sqm 21715.00

made out of avg. 2 mm aluminium sheet / 4mm ACP (Aluminum

composite Panel) of requred sizes ,coated with one coat of epoxy

primer and two coats of best quality epoxy paint, reflectorised

with High Intensity Prismatic Grade retro refiective sheeting . The

details of symbol for each board shall be as per the instruction of

engineer in charge. The fixing on wall / door at site shall be done

with necessary screw etc.complete under the supervision of

engineer in charge.

[105] Provding P.V.C. 100 mm diameter water spouts including 22.00 Each 159.37

necessary iron gratings as per drawings.

[106] SIGNAGES ON WALL 30.00 No 1060.50

Providing, Fabricating & Fixing wall signage's using 304 grade

Stainless steel brushed steel finish plate of 1.5 mm thick fixed on a

wall using s.s studs including punched (laser cut) lettering carried

out on s.s plate of required size and text as directed by Engineer

over the S.S plate etc.complete.

Size: 18" x 12"

[107] SIGNAGES ON Door / Wall 40.00 No 757.50

Providing, Fabricating & Fixing 304 grade Stainless steel 1.5 mm

thick brushed steel finish plate fixed on a door using s.s studs and

with punched(laser cut) lettering carried out on s.s plate of

required size and text as directed by Engineer etc. complete.

[108] Providing and fixing coloured self adhesive PU Tactile tile, ground 114.00 Sqm 4575.30

surface indicators of Poyurethene of size 300 mm x 300 mm for

guilding / warning to the visually visitors in the center / side of the

pedestrian / approach pathway as per specificatio and guidelines

complete in all respect to the entinre satisfaction of Engineer in

[109] Providing and fixing Acrylic multilingual braile (raised dots) 80.00 Each 1292.80

DIRECTIONAL SIGNBOARDS of size 225 x 150 mm designed as per

accessibility standards and having 3.5 mm thick acrylic base plate

with Upper Case San Serif words made of white acrylic non glare

cut out letters of height 15 mm raised not less than 0.8 mm above

base plate and the equivalent word written in Gujarati, English or

Hindi non glare acrylic cut arrow pointing in the require direction.

Each signboard to be fixed as per manufacturers specifications on

the wall at the approved location and at a height of 1200 mm from

Floor level complete as per design / specifications and guidelines

as per entire satisfaction of the Engineer in charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[110] Providing and fixing Braile indicator of size 170 mm x 35 mm for 50.00 Rmt 858.50

hand rails of the approved design and hame have braile dots

raised 0.5 mm above the base plate to be installed at specific

locations as per direction of Engineer in charge.

[111] Providing and fixing tactile layout plan of size 900 mm x 600 mm as 3.00 Each 42824.00

approved design, made of 3.0 mm thick acrylic non glare base

plate and non glare cut out symbols with Braile on which individual

facility points, like inquiry, reception, restrooms, medical room /

first aid, cafeteria or breakout area,lounge, meeting room,

conference room etc. present the respective floor with pictograph

wherever needed all in tactile raised by minimum of 1 mm to

mm in various colours to make it legible for seniors, partial vision

impaired etc. All the faciity name should be in Braile, along with

Gujarati, English or Hindi. The entire block of tactile signs should

be mount on wall for easy reading. The map to be installed at

specified locations and installed at height of 800 mm from ground

level complete in all respect as per Harmonized guideline &

satisfaction of Engineer in charges.

[112] Providing and fixing of acrylic, non-glare, tactile audio pictorial 3.00 Each 45753.00

building layout as per the approved size, design and make, having

3 mm thick acrylic non glare base plate of the approved colour and

non glare acrylic cut out symbols raised 3 mm above base plate

and Grade - 2 / Grade - 1 Braile to be intergral with the sign face

and be raised 0.5 mm above base plate. The map to be installed at

the specified location as per accessibility standards shall be

oriented to the position of the viewer and to be installed at the

height of 800 mm from the finished ground / floor level and using

the necessary hardware specified by the manufacturer and to be

installed complete as per design / specifications and guidelines as

per the entire satisfaction of the engineer in charge.

[113] Providing and fixing in position 300 mm high, 150 mm wide English 60.00 Each 757.50

letters made from 1.0 mm thick stainless steel sheet as directed by

Engineer-in-charge with all necessary tools & plants etc. complete.

[114] Providing and applying a uniform coat of residual petroleum 2535.00 Sqm 161.60

bitumen of approved quality at the rate of 1.7 kg per square metre

on the damp proof course (DPC) surface, including thorough

cleaning of the surface with brushes and final wiping with a piece

of cloth lightly soaked in kerosene oil to remove dust, dirt, and

loose particles, complete as directed by the Engineer-in-Charge.

[115] Providing and fixing in position 150 mm high, English letters made 60.00 Each 454.50

from 1.0 mm thick stainless steel sheet as directed by Engineer-in-

charge with all necessary tools & plants etc. complete.

[116] Demolition of Brick work and stone masonry including stacking of 98.00 Cum 536.09

serviceable materilas and disposal of unserviceable materials with

all lead and lift.(ii) In Cement Mortar.

[117] Dismentling steel work including distempering and stacking the 2762.00 Kg 3.67

materials with all lead and lift.

[118] Providing and laying controlled C.C. M.200 & curing complete 29.00 Cum 7549.79

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in Columns

[119] Providing TMT Bar FE 500D reinforcement for R.C.C. work including 38997.00 Kg 76.21

bending, binding and placing in position complete upto floor two

[120] Brick work using common burnt clay building bricks having 137.00 Cum 4289.32

crushing strength not less than 35 kg./Sq.Cm. in Super Structure in

Cement Mortar 1:6 (1- Cement : 6 -fine sand) (B) Conventional

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[121] Providing 15mm thick cement plaster in single coat on Rough 1261.00 Sqm 194.07

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (i) Cement mortar

1:3 (1-cement:3-sand)

[122] 20mm thick sand faced cement plaster on walls upto height 10 1095.00 Sqm 335.65

metres above ground level consisting of 12mm thick backing coat

of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of

C.M. 1:1 (1-cement : 1-sand) etc. complete.

[123] Steel work, welded in built up sections framed work including 23.60 q 9725.85

cutting, hoisting, fixing in position and applying a priming coat of

red lead paint. (D) In trussses and trussed purlins, upto 25 M. span

and 15 M. ovarall height.

[124] Providing and fixing 0.90 m high fencing with M.S. angle posts of 241.00 Rmt 353.50

size 40 mm × 40 mm × 6 mm, fixed at 2.50 m centre-to-centre,

including three coats of oil painting. The fencing shall consist of

three horizontal lines and two diagonal lines of galvanised steel

barbed wire weighing 9.38 kg per 100 m, along with razor wire of

0.5 mm blade thickness and 2.5 mm core wire, with coil diameters

ranging from 300 mm to 1500 mm. The barbed wire and razor wire

shall be properly strained and fixed to the posts using G.I. staples,

including fixing the posts on the compound wall, complete in all

[125] Providing and laying controlled C.C. M.250 & curing complete 46.00 Cum 7615.57

including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work including all .in RCC

[126] Providing and laying controlled cement concrete M.200 and curing 34.00 Cum 6128.47

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in SLAB

[127] Brick work using common burnt clay building bricks having 39.00 Cum 4289.33

crushing strength not less than 35 kg./Sq.Cm. in Super Structure

superstructure above plinth level in Cement Mortar 1:6 (1-

Cement : 6 -fine sand) (B) Conventional for Ground Floor

[128] Providing and laying controlled cement concrete M.200 and curing 11.00 Cum 7446.85

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in Lintel /

Coping Ground Floor

[129] Providing and laying controlled cement concrete M.200 and curing 27.00 Cum 6073.26

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in Beams

[130] Providing and laying controlled cement concrete M.200 and curing 3.60 Cum 8069.37

complete including the cost of formwork and but excluding the

cost of reinforcement for reinforced concrete work in CHHAJJA

including finishing coat CM (1:3) for chhajja plaster for Ground

[131] Providing 10mm thick cement plaster in single coat on 185.00 Sqm 169.25

brick/concrete walls for interior plastering upto floor two level and

finished even and smooth in (i)Cement mortar 1:3 (1-cement:3-

sand) for plastering on ceilings and sofits of stairs Ground Floor

[132] Providing 20 mm thick cement plaster in single coat on brick / 168.00 Sqm 259.87

concrete wall for interior plastering up to floor two level finished

even and smooth (ii) Cement mortar 1:3 ( 1-cement ,3 - sand ) and

mixing waterproofing materials in cement mortar in proportion

recommended by the manufacturer for All Floor.s etc. all complete

as directed by engineer in charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[133] Providing and laying 300X300 MM & 10 MM THK MATT FINISHED 55.00 Sqm 908.32

GLAZED TILES in flooring treads of steps and landing laid on a bed

of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand )

finishing with flush pointing in white cement.

[134] Providing and laying 300X450 MM & 10 MM THK GLAZED TILES 120.00 Sqm 1484.60

DADO in skrting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with white

[135] Providing and laying Hand dressed polished blue Kota stone slab 69.00 Sqm 1090.44

flooring over 20mm (Average) thick base of cement mortar 1:6 (1-

cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse

sand) laid over and jointed with grey cement slurry mixed with

pigment to match the shade of slab including rubbing and

polishing etc. complete. (A) 25mm thick

[136] Fire Fighting Fire Pump Room & Accessories Supplying, Installation, 1.00 No 263105.00

Testing and commissioning of Electric driven Main Fire Hydrant

pump suitable for automatic operation and consisting of following:

Horizontal type, centrifugal End Suction pump of cast iron body &

bronze impeller , mechanical seal to ensure a minimum pressure

of 3.5 kg / sq.cm. at highest and farthest outlet at specified flow of

137m3/Hour@ 70M. head with M.S.fabricated common base

plate, coupling, coupling guard, foundation bolts etc. as required

[137] Supplying, Installation, Testing and commissioning of Diesel engine 1.00 No 517726.00

driven fire pump suitable for automatic operation and consisting

of following: Horizontal type, centrifugal End Suction pump of cast

iron body & bronze impeller , mechanical seal to ensure a

minimum pressure of 3.5 kg / sq.cm. at highest and farthest outlet

at specified flow of 137m3/Hour@ 70M. head conforming to IS

1520. with M.S.fabricated common base plate, coupling, coupling

guard, foundation bolts etc. as required

[138] Supplying, Installation, Testing and commissioning of Jockey Pump 1.00 No 106151.00

10.8M3/hour @70M Head.Horizontal Centrifugal End Suction. with

M.S.fabricated common base plate, coupling, coupling guard,

foundation bolts etc. as required

[139] Supplying, Installation, Testing and commissioning of cubical type 1.00 No 131906.00

floor mounted power cum Fire Pump control panel complete with

suitable switch gear, bus bars, relays, contractors, indicating

lamps, fuses, instruments manual isolator & auxillary switch

including connections complete as required.(Contractor should

submit GA Drawing for approval before deliver the Panel at Site)

[140] Providing, fixing, testing and commissioning below Caballing work 30.00 Rmt 292.90

for Fire Pumps (Only from Panel to Pumps) 3 C X 35 Sqmm

Alluminium Armoured

[141] Providing, fixing, testing and commissioning below Caballing work 30.00 Rmt 181.80

for Fire Pumps (Only from Panel to Pumps) 3 C X 16 Sqmm

Alluminium Armoured

[142] Providing, fixing, testing and commissioning below Caballing work 150.00 Rmt 113.12

for Fire Pumps (Only from Panel to Pumps) 2 C X 1.5 Sqmm Copper

[143] Providing, fixing, testing and commissioning below Caballing work 15.00 Rmt 353.50

for Fire Pumps (Only from Panel to Pumps) Perforated G.I.sheet

cable tray Cable Tray . 300X300X50mm .

[144] Providing, fixing, testing and commissioning below Caballing work 20.00 Rmt 252.50

for Fire Pumps (Only from Panel to Pumps) Perforated G.I.sheet

cable tray Cable Tray . 150X150X50mm .

[145] Cutting hole by Mechanical Means of upto 200 mm dia in 50.00 No 2020.00

slab/beam throughout the thickness

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[146] Providing, fixing, testing & commissioning of Glicerin Filled dial 4.00 No 1358.45

type Pressure Gauge and range of 0-15 Kg/cm2

[147] Providing, fixing, testing & commissioning of Pressure Switches for 3.00 No 1010.00

automation of fire pumps. Pressure switches shall be double pole

single throw type suitable for 3 phase supply with diaphragm.

Aluminum Enclosure with IP 66 protection as required..

[148] Supplying, Installation, Testing and commissioning of C.I.Butterfly 7.00 No 5181.30

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 150mm dia.

[149] Supplying, Installation, Testing and commissioning of C.I.Butterfly 5.00 No 3817.80

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 100mm dia

[150] Supplying, Installation, Testing and commissioning of C.I.Butterfly 1.00 No 3181.50

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 80mm dia.

[151] Supplying, Installation, Testing and commissioning of C.I.Butterfly 7.00 No 2716.90

valve conforming to I.S:13095 class PN 16 rating with Fittings,

Flanges, Nutbolts, Washers, Gaskets etc.of size: 50mm dia.

[152] Providing, fixing, testing and commissioning of C.I. Dual plate type 6.00 No 7383.10

Non-Return Valve class PN 16 rating with fittings, flanges, nutbolts,

washers, gaskets etc.of sizes: 150mm dia

[153] Providing, fixing, testing and commissioning of C.I. Dual plate type 2.00 No 4332.90

Non-Return Valve class PN 16 rating with fittings, flanges, nutbolts,

washers, gaskets etc.of sizes: 80mm dia

[154] Providing, fixing, testing and commissioning of C.I. Dual plate type 3.00 No 2979.50

Non-Return Valve class PN 16 rating with fittings, flanges, nutbolts,

washers, gaskets etc.of sizes: 50mm dia

[155] Supply, Installation, Testing and Commissioning of S.S. Ball Valves 9.00 No 1272.60

with all fittings required. 25mm dia.

[156] Supply, Installation, Testing and Commissioning of S.S. Ball Valves 7.00 No 1191.80

with all fittings required. 15mm dia.

[157] Providing, fixing, testing and commissioning of Above Ground MS. 362.00 Rmt 2121.00

ERW Black C Class Heavyduty pipes as per IS: 1239 (upto 150 mm

dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 150mm dia

[158] Providing, fixing, testing and commissioning of Above Ground MS. 84.00 Rmt 1424.10

ERW Black C Class Heavyduty pipes as per IS: 1239 (upto 150 mm

dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 100mm dia

[159] Providing, fixing, testing and commissioning of Above Ground MS. 115.00 Rmt 1010.00

ERW Black C Class Heavyduty pipes as per IS: 1239 (upto 150 mm

dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 80mm dia

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[160] Providing, fixing, testing and commissioning of Above Ground MS. 110.00 Rmt 656.50

ERW Black C Class Heavyduty pipes as per IS: 1239 (upto 150 mm

dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 50mm dia

[161] Providing, fixing, testing and commissioning of Above Ground MS. 426.00 Rmt 303.00

ERW Black C Class Heavyduty pipes as per IS: 1239 (upto 150 mm

dia.) and IS: 3589 (upto 200 mm dia. And above) including cutting,

screwing, welding etc. and providing all fittings like flanges, bends,

tees, elbows, reducers, clamps, hangers etc. with painting of one

coat of primer and 2 or more coats of synthetic enamel paint of

approved make / shade complete as per specification. 25mm dia.

[162] Supplying, installing and commissioning of Foot Valve with,suitable 2.00 No 15705.50

flanges, nuts, bolts, gaskets etc. complete. 150mm dia

[163] Supplying, installing and commissioning of Foot Valve with,suitable 1.00 No 10524.20

flanges, nuts, bolts, gaskets etc. complete. 80mm dia

[164] Fire Fighting Equipement Providing, fixing, testing and 13.00 No 5262.10

commissioning of SS Single Headed Oblique Pattern Hydrant

Landing Valves as per IS: 5290 with 80 mm dia flanged inlet &

mm dia female outlet complete with cap and chain etc.

[165] Providing, fixing, testing and commissioning of SS Branch Pipe with 13.00 No 1696.80

nozzle of 25 mm nominal bore outlet suitable to fit with standard

instanteneous type 63 mm dia coupling. As per IS:903

[166] Providing, fixing, testing and commissioning of 63 mm dia 15m 26.00 No 3989.50

long RRL Hose Pipe with 63 mm dia.Type A Male and female

Stainless Steel couplings duly binded with GI wire, rivets etc.

conforming to IS 636 as required.

[167] Providing, fixing, testing and commissioning of weather proof 13.00 No 3646.10

standard fire Hose Cabinet wall mounting type 18 Guage. (750 x

600 x 250) having Double Opening with M.S. fabricated stand,

necessary locking arrangement by allan key.

[168] Providing, fixing, testing and commissioning of Wall mounting Fix 5.00 No 5948.90

type First aid Fire Hose Reel with drum, hanging bracket, 36 M x

mm dia high pressure hose reel tubing as per IS:884 with shut

nozzle and ball valve and all required accessories.

[169] Providing, fixing, testing and commissioning of CI Four way Fire 1.00 No 12311.90

Brigade Inlet as per IS: 904 having 63 mm dia inlet with 150 mm

dia Butterfly valve blank cap and chain with necessary fittings,

flanges, nutbolts etc.

[170] Providing, fixing, testing and commissioning of Two Way Fire 2.00 No 11463.50

Brigade Inlet for Draw Out Connection with 100mm dia Foot Valve.

blank cap and chain with necessary fittings, flanges, nutbolts etc.

[171] Providing, fixing, testing and commissioning of 25 mm dia Air 2.00 No 1363.50

Release Valve and Ball Valve assembly on top of each riser for Air

release system.

[172] Supplying, Installation, Testing and commissioning of ABC type 6 28.00 No 1696.80

Kg Fire Extinguisher Mono Ammonium Phosphate Powder

Stored Pressure Type, Pressure Gauge, Controllable discharge

mechanism Class A, Rating 3A & Class B rating 21B as per IS

ISI MARK (ABC Dry Chemical Powder - MAP 50%).

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[173] Providing & fixing of CO2 type Fire Extinguisher of capacity 4.5 kg 28.00 No 3989.50

filled with Co2 Gas as per IS 15222 with controll discharge

mechanis, fitted with Hose & Horn applicable on Class B fire rating

21B confirms to IS 15683 bearing ISI mark. Co2 cylinder as per IS

[174] Providing, fixing, testing and commissioning of M.S. ERW Black C 68.00 Rmt 797.90

Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.) and IS:

3589 (upto 200 mm dia. And above) including cutting, screwing,

welding etc. and providing all fittings like flanges, bends, tees,

elbows, reducers, clamps, hangers etc. with painting of one coat of

primer and 2 or more coats of synthetic enamel paint of approved

make / shade complete as per specification. 65mm dia.

[175] Providing, fixing, testing and commissioning of M.S. ERW Black C 72.00 Rmt 464.60

Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.) and IS:

3589 (upto 200 mm dia. And above) including cutting, screwing,

welding etc. and providing all fittings like flanges, bends, tees,

elbows, reducers, clamps, hangers etc. with painting of one coat of

primer and 2 or more coats of synthetic enamel paint of approved

make / shade complete as per specification. 40mm dia.

[176] Providing, fixing, testing and commissioning of M.S. ERW Black C 50.00 Rmt 383.80

Class Heavyduty pipes as per IS: 1239 (upto 150 mm dia.) and IS:

3589 (upto 200 mm dia. And above) including cutting, screwing,

welding etc. and providing all fittings like flanges, bends, tees,

elbows, reducers, clamps, hangers etc. with painting of one coat of

primer and 2 or more coats of synthetic enamel paint of approved

make / shade complete as per specification. 32mm dia.

[177] Providing and fixing, testing and commissioning of K 5.6 Pendent 225.00 No 404.00

type Standard Response Sprinkler rating of 68deg.C. with required

accessories.UL Listed

[178] SS Sprinkler rossette plate. 225.00 No 85.85

[179] Supplying, Installation, Testing and commissioning of SS Flexible 225.00 No 1010.00

drops 1200/1500mm Long.Unbraided , Maximumm Service

pressure 175PSI,.Sprinkler Flexible Drop system is a ready to use

assembly to fit sprinkler heads in desired location in a suspended

ceiling. It easily positions the sprinkler in center of the ceiling tile

at a correct height

[180] Supplying, Installation, Testing and commissioning of Flow Switch 4.00 No 4696.50

on sprinkler distribution header on each floor with necessary

Junction Box and shall be connected to fire alarm panel through

cable. Flow switch shall be "UL" Listed size 150mm dia/ 100mm

dia/ 80mm dia. (Flow switch cabling to monitor module to FACP in

ELV Contractor Scope)

[181] Supplying, Installation, Testing and commissioning of Inspector 4.00 No 7221.50

test assembly complete with test valve, sight glass sectional drain

valve, union; necessary piping, threading, jointing & with corrosion

resistant orifice all complete strictly as per drawing.25mm dia.

[182] On - Off Pump Trigger System. Providing, fixing, testing and 5.00 No 424.20

commissioning of On -Off Switch.

[183] Providing, fixing, testing and commissioning of 3 Core X 1.5 Sqmm 150.00 Rmt 85.85

flexible Cable with PVC Condiut.

[184] Providing, fixing, testing and commissioning of below Auto Glow 45.00 No 171.70

Signages. Emergency Exit 4” X 12”

[185] Providing, fixing, testing and commissioning of below Auto Glow 40.00 No 339.36

Signages. Fire Fighting Equipements .8” X 12”

[186] Providing, fixing, testing and commissioning of below Auto Glow 10.00 No 323.20

Signages. In Case of Fire do not use Lift ,Use Staircase 8"x 8"

[187] Providing and fixing of convention Below Ceiling smoke detector 87.00 No 3232.00

complete with mounting base as required.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[188] Providing, Installing & Commissioning the Manual call point zone 12.00 No 3817.80

convention type of best standard quality brand including labour,

material, loading, unloading, transportation ,taxes , tools

accessories etc complete as per direction of Engineer In Charge.

[189] Providing , Installing & Commissioning the Hooter 24 v Zone 12.00 No 3817.80

Convention Type of best standard quality brand including labour,

material, loading, unloading, transportation ,taxes , tools

accessories etc complete as per direction of Engineer In Charge.

[190] SITC Of Addressable Fire Alarm Panel 1.00 No 106100.50

[191] Providing and fixing of 2x1.5 sqmm fire alarm armoured cable, 1600.00 Rmt 103.02

600/1000V rated with annealed copper conductor having XLPE

insulation, steel wire armouring &FRLS outer sheath complete as

[192] APPROVAL FIRE SYSTEM FROM LOCAL FIRE AUTHORITY Getting of 1.00 Job 303000.00

Fire Fighting System Approval from local fire authority with all

other charges and documentations for getting No Objection

[193] Box cutting the road surface to proper slope and camber for 558.00 Cum 104.20

making a base for road work including removing the excavated

stuff and depositing on the road side slope as directed upto

[194] Supplying and stacking of graded stone aggregate of following size 186.00 Cum 1150.60

(for W. B. M. ) including Spreading the stone aggregate for rolling

including filling the interstices to required camber and gradient

Machine crushed stone aggregate 45 mm to 63 mm size

[195] Supplying and stacking of Soft murrum / Binding materials 47.00 Cum 669.71

including spreading road crust filling the gaps in metal and leveling

to camber and gradient as directed.

[196] Rolling and consolidating water bound macadam (except laterite 1239.00 Sqm 21.00

and Kankar) including watering not exceeding 150mm thickness

(Main layer including binding materials ) including filling in

depressions which occur during the process.(A) With power roller

exceeding 8 tonne and not exceeding 12 tonne.

[197] Providing and laying controlled C.C.M.250 road pavement & curing 159.00 Cum 5068.64

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in RCC road including

Compaction and finishing of cement concrete road by trimix

process providing extra labour charges for the trimix vacum

dewatering service process on cement concrete road surface by

using vacum dewatering pump floater surface vibrator including

making grooves , filling grooves and rough finish to surface as per

in including levelling the complete etc. complete as per instruction

of Engineer In Charge.

[198] Supplying promoulded bituminous joint filler.(i) 12mm thick 3.00 Cum 553.79

[199] Providing laying (to level or slopes) and jointing reinforced 60.00 Rmt 665.47

concrete Light duty non-pressure pipes I.S. class NP2 of the

following internal diameter with collars and butt ends prepared for

collar joints including testing of joints complete.(D) 300mm

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[200] Providig & Fixing Heavy Duty (HD 20 ) SFRC Precast Concrete 8.00 No 3535.00

Grating Cover with Frames manufactured as per IS: 12592 by high

frequency vibration techniques with high quality in-house

produced moulds, requisite Concrete Grade of M 30 and proper

reinforcement & tank immersed curing is done. Grating covers

shall be provided with suitable lifting hooks, suitable taper

provided in cover to prevent jamming inside frame & M S Strip of

suitable thickness provided for edge protection etc. complete as

per instruction of Engineer In Charge.

Cover Size - 700 x 700 mm, Frame Size - 850 mm x 850 mm & Cover

Height 95 mm , Frame Height 150 mm

[201] Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1-cement 4.00 Each 19330.46

:2-coarse sand : 4-graded stone aggregate 20mm nominal size)

foundation concrete 1:3:6 mix (1-cement : 3- coarse sand :6-Brick

bats 40 + 50mm size) inside plastering 15mm thick with Cement

Mortar 1:3 (1-Cement : 3-coarse sand) finished with a floating coat

of neat cement and making channels in cement concrete 1:2:4 mix

(1-Cement :2-Coarse sand :4-stone aggregate 20mm nominal size)

finished smooth complete including curing and festing (i) Inside

size 900mm x 1200mm and 1.5M. deep including C.I. cover with

frame size 560mm diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame

Kg.)(A) With 230mm thick walls of brick msonry using brick having

crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar

1:5 (1- Cement: 5-Coarse sand) (2) B type depth 1.50 Metre for

150mm diameter sewer.

[202] Steel work, welded in built up sections framed work including 73.50 q 9725.84

cutting, hoisting, fixing in position and applying a priming coat of

red lead paint. (D) In trussses and trussed purlins, upto 25 M. span

and 15 M. ovarall height.

[203] Providing and fixing PROFLEX type self Supported Roof {Arch Type} 669.00 Sqm 1848.30

using Cold rolled, Galvalume Steel colour coated sheet 1.0 mm

thick conforming to ASTMA 653, A792 DIN, Alu Zinc Coating :

AZ150 and Regular Modified Polyester painting with epoxy primer

service coat at bottom, including necessary fixtures & fastenings

for Lighting arrangement in parking shade, design & shape as

approved by Engineer in charge etc. complete.

[204] Lawn Grass:- Supplying & Filling the area upto the depth of 30 cm. 650.00 Sqm 363.60

with good quality of field fertile soil, preparing soil for planting by

supplying and mixing Farm yard Manure at the rate of 5 Cum per

100 Sq. Mtr. Area , providing and planting suckers of pure dharo

(doob) grass roughly at 10 cm X 10 cm distance and maintaining till

well established etc. complete. (about 90 days)

[205] Providing and plantation of Ornamental plants like areca palm, 40.00 No 681.75

bottle palm,adenium or equivalent etc. by digging of pit size 2x2x2

ft including DAP, Pestisides, plantation and saplings and making

proper Tree basin and putting proper support like bottle

palm,Areca Palm, Adenium or equivalent etc of 2ft to 6ft height

well growth or as directed by engineer in charge and maintaining

till well established etc. complete. (about 90 days)

[206] Providing and plantation of plants like Kadam, ,English Rose or 10.00 No 303.00

equivalent etc by digging of pit size 2x2x2 ft including DAP,

Pestisides, plantation and saplings and making proper Tree basin

and putting proper support of 2ft to 4ft height well growth or as

directed by engineer in charge and maintaining till well

established etc. complete. (about 90 days)

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[207] Providing and plantation of Cycus by digging of pit size 2x2x2 ft 20.00 No 4040.00

including DAP, Pestisides, plantation and saplings and making

proper Tree basin and putting proper support like cycus plant of

3ft to 6ft height well growth or as directed by engineer in charge

and maintaining till well established etc. complete. (about 90 days)

[208] Providing and plantation of Decorative Plants with good quality 50.00 No 75.75

manure & Soil plant likes Canna,Mogra, Allamanda, Jasmine,Desi

Gulab,Parijaat,Ratrani etc or equivalent of well growth or as

directed by engineer in charge and maintaining till well established

etc. complete. (about 90 days)

[209] Providing tree plants having minimum 1.00 mt. height and healthy 30.00 No 252.50

growth of various kinds as like Platform gulmahore Kananj Ambla,

Ranitree, Saptaparni, Cherry, Cryjeliya, Spethodia, Paras Pipala,

Gromalo, Nem, Borsalli,Buch, Chompo, Asopalav and as suggested

etc. complete.as directed by engineer in charge and maintaining

till well established etc. complete. (about 90 days)

[210] Drilling of Tubewell by direct rotary rig in alluvial starta 120.00 Rmt 756.49

Drilling of Pilot bore hole in Alluvial strata by direct Rotary rig.of

size 250 mm diameter.

Alluvial area complete upto 300 m (kheda District)

[211] Reaming of 250/300 mm dia. pilot bore hole including assembling, 120.00 Rmt 465.61

lowering housing casing ,strainer pipes, gravel packing, clay

packing etc. 550 mm dia

[212] Providing and supplying in standard length ISI mark rigid 140.00 Rmt 920.11

unplasticised PVC pipes suitable for potable water with ring fit

joint including cost of rings, as per IS specification no. 4985/1988

including all local and central taxes, transportation, freight

charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores and including cost of

jointing meterial etc. complete.(3.1/B) Test Pressure 6 Kg/cm2 (9)

[213] Lowering and removing of 100 mm dia dropline and 32 mm dia 120.00 Rmt 149.48

airline for development of each water bearing Zones come across

up to full depth of Deep tubewell of size 200 mm/250 mm/300 mm

dia for the tubewell having depth upto depth 186 Meter depth

through suitable air compressor. The job is for complete period of

development of tubewell.( where water is very deep and 2/3rd

submersion is not achived.) All the required accessories,

machineries etc for above job will have to be provoded by

[214] Providing and lowering of 200 mm dia PVC Test Pressure 6 Kg/cm2 30.00 Rmt 404.00

slotted pipe etc complete as per instruction of Engineer In Charge.

[215] Clamp made from M.S. plate with 3 holes on either side with nuts 2.00 Per Pair 1643.98

& bolts of Std. Make and suitable size.

(g)750 mm X 75 mm X 16 mm flat to 200 mm dia.Pipe.

[216] Bore plug of 100 mm height made from MS plate with 3 holes at 1.00 No 782.56

equal distance on circumference for nut-bolts type, locking

arrangement with nutsbolts & lock nuts of standard make etc.

(B) From 5 thick M.S. Plate (For Top also)

(ii) Suitable for 200 mm dia pipe.

[217] Bail plug of length 0.45 meter made from MS medium class pipe as 1.00 No 851.03

per IS suitable for

(B) 200 mm dia pipe.

[218] Steel bent plate suitable to ERW pipe as detailed below ERW Pipe 1.00 No 67.25

Size in mm.(b) 200 mm dia. 150 X 150 X 6 mm

[219] Supply of best quality well sorted Sevaliya gravel of size ranging 15.00 Cum 2049.29

from 4 mm to 6mm.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[220] Electrologger charges (With carting) (B) For other dept. 1.00 Job 18180.00

[221] Air Compressor 1.00 LS 27603.30

Charges of air compressor for test of tube well by air compressor

of 900 CFM / 200 PSI capacity Upto clear water discharge

[222] Geophysical & geohydrological ground water investigation for 1.00 No 14428.86

finalisation of one pin point including vehicle charges.

[223] Manufacture, supply and delivery of 65 mm size CI pipe adaptor 1.00 Set 745.69

and pump adaptor for UPVC column pipes.

[224] Manufacture, supply and delivery of following ISI marked HDPE 120.00 Rmt 84.84

pipes (IS:4984/1985 with latest amendment) having material

Grade PE-80 in approximate 100 meter coil length or as per

GWSSB requirement with SS- 316 nipple at both ends having 11 TPI

threads as per specifications, press fitted and bolted having

nominal diameter as under as per detailed technical specifications.

iii)DN 50 PN-10

[225] Supply of nut bolt rubber packing and required materials and 1.00 LS 3030.00

dilevery connection for new bore.

[226] Earthwork for embankment including breaking clods, dressing with 1760.00 Cum 169.98

all lead and lift (including watering and consolidation)(B) From

Borrow area within 0.5 Km.lead

[227] Clearing and grubbing road land including uprooting rank 0.35 Hect. 80243.80

vegetation grass bushes,shrubs,sapling and trees girth up to

mm removal of stumps of trees cut earlier and disposal of

unserviceable materials(A) By manual means in area of light jungle

[228] Providing Rain Water Harvesting 2 m. x 2 m x 4 m Pit for water 1.00 No 60612.70

logging with excavation in any strata up to 4 m depth, filling the pit

with brick bats in 0.6 m depth, 0.30 m depth with 10 mm To

mm Kapchi, 0.30 m depth with 6 to 10 mm grit and 2.00 m depth

with coarse sand in layers including making P.V.C. Pipes 10 kgf /

Sq.cm. 110 mm dia. line for water inlet etc. as directed, 300 mm

dia bore up to 50 Mtr. depth and 160 mm dia perforated PVC pipe

casing - 48 Mtr. length and making connections etc. complete as

directed for recharge well for rain water harvesting.

[229] Providing and constructing a Filter Chamber of size 3.06 x 2.21 x 1.00 No 56283.44

1.20 mt. as including connecting of rain water pipes as per detail

drawing and as directed by Engineer-in-charge.

[230] Half brick masonry in common brunt clay building bricks having 28.00 Sqm 641.16

crushing strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:5

(1- Cement : 5 -coarse sand ) in superstructure above plinth level

(B) Conventional for Ground Floor

[231] Providing and fixing 35 mm thick single shutter flush door (with 6.00 Sqm 3405.01

pattern laminate on both side in situ lamination work) , solid core

construction with frame of first class hardwood with cross board

and face veneer or plywood face panels, lipping with teak wood

battens 25 mm minimum depth on all edges of flush door shutters,

including anodised alluminium butt hinges with necessary screws.

(B) Non-decorative type and block board core anodised

alluminium butt hinges in flush door shutters , Shutters with both

side Decorative 1 mm thick Laminated sheet, pattern and design is

to be approved by the Engineer In Charge with SS handle, Tower

Bolt, magnetic door catcher,6 lever Mortise lock with two key set

etc. complete as directed by Engineer In Charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[232] Providing and fixing FRP of 35mm thick Fiber Glass shutter with 1.5 6.00 Sqm 1269.63

to 2.0 mm thick fire retardent grade FRP skin in depressed panel

design having extra reinforcement on sides & edges & in Gel coat

finish. The core of the shutter is to be filled up with injected

retardent grade polyurethane foam done in situ alongwith

embedded wooden pieces for stiffening & also taking hinges &

fintures. The whole FRP frame & shutter is to be water proof

,weather proof, termite proof & resistance to mild acid/alkali.

Rates are to be inclusive of S.S hinges with necessary screws &

alluminium fixtures & fastenings.

[233] Providing and fixing rolling shutters of approved make made of 80 29.00 Sqm 3503.40

mm wide M.S. laths inter-locked together through their entire

length and jointed together at the ends by end locks mounted on

specially designed pipe shaft with bracket plates, guide channels

and arragements for inside and outside locking with push-pull

operation including the cost of hood cover and spring etc.

complete.(A) Shutters having width below 3.5 M.

[234] Providing and fixing Hood cover for rolling shutters (A) Shutters 6.00 Rmt 121.23

having width below 3.5 meters

[235] Providing and fixing three track standard extruded colour anodized 11.00 Sqm 4288.75

aluminum section of best quality brand equivalent to JINDAL

Series E (30 mm) section numbers are shutter top & bottom-

20993, shutter inter lock - 20550, shutter side (handle) -

frame-bottom with gutter- 21203, frame top & side - 20837 with

three shutters with 5 mm thick transparent bronze colour tinted

float glass and One shutter with Stainless Steel wire net with

rubber gasket,air lock strip and finishing joints with silicon sealant,

with standard extruded colour anodized aluminum coated fittings

and fixture with mosquito net shutter etc. complete as per

instruction of Engineer In Charge for Window.

[236] Providing and fixing glazed louvered glass windows and ventilators 1.10 Sqm 4143.56

with teak wood frame 10cm. x 7cm. Size including 3 coats of oil

painting to wood work etc.complete.

[237] Providing & filling 3-4 mm wide groove filled with Epoxy grout of 42.00 Rmt 48.08

best quality Brand as directed by Engineer In Charge.

[238] Providing and laying polished kota stone slab 25mm thick in risers 3.00 Sqm 1127.84

of steps,skirting Dedo and pillars laid on 10mm thick cement

mortar 1:3 (1-Cement : 3 coarse sand) and jointed with gray

cement slury mixed with pigment to match the shade of slab

including rubbing and polishing etc. complete.

[239] Providing and laying 300X900 MM & 10 MM THK GLAZED TILES 32.00 Sqm 938.54

DADO in skrting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with white

[240] Providing and laying water proofing treatment with china mosaic 139.00 Sqm 1125.04

tiles flooring over avg. 50 mm thick C.C. 1:2:4 {1 Cement : 2 sand :

4 Kapachi / Gritt 6 to 12 mm size} bedding for maintaining slope

for plain and curve surface & 12 mm to 20 mm of broken piece of

seramic / glazed tiles ( one for more color as directed ) to be laid

over cement mortar bedding of C M 1:3 (1 cement : 3 sand )

containg one Kg of water proofing materials per bag of O P C at

plain or / and slops and to be tempered to bring mortar ceramic

up to surface with using white cement and colour pigment

including rounding of junctions and extending them up to 15 cm

along the wall and curing with bends any pattens or design as per

drawing and cleaning by using oxalic acid etc complete.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[241] Providing and fixing COUNTER WASH BASIN - CLIFF SNOW WHITE 3.00 Each 4030.35

COLOUR-550 X 460 X 185 MM with single hole for pillar tap with

C.I. or M.S. brackets painted white including sutting holes and

making good the same with brass union and CP brass wall

discharge pipe with flanges and cap of best quality brand , Waste

Pipe for Wash basin C.P. 32 mm dia with fittings up to floor trap,

32mm dia CP brass waste coupline with CP chain and rubber plug,

washer and CP brass cap complete in all respects including cutting

and making good the walls RCC work as directed and making good

the same etc. complete.

[242] Dismentling of doors, windows, ventilators etc. (wood or steel) 6.00 No 182.94

shutters including chowkhats architraves, holdfasts and other

attachment etc. complete and stacking them within all lead and lift

(ii) Not Exceeding 3 Sq.M. in area.

[243] Dismentaling tiled of stone floors laid in mortar including stacking 20.00 Sqm 46.77

of serviceable materials and disposal of unserviceable materials

with all lead and lift

[244] Demolition including stacking of serviceable materilas and disposal 17.00 Cum 1030.81

of unserviceable materials with all lead and lift. (i) R.C.C. work

[245] Dismantling santtary fittings like wash basin . W.C. pan Indian and 2.00 No 394.51

European type, flushing tank etc. including stacking the materials

with all lead and lift.

[246] Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 713.00 Pt. 410.06

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on PVC

/ Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder with

adaptor/ceiling rose / H.D.Connector as directed.(j) in existing pipe

erected concealed in wall/ceiling complete.Cat.III

[247] Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 227.00 Pt. 556.51

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of

pipe erected with 6A Modular type switch and hum free EME

step type electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary ceiling rose /

H.D.Connector as directed.(j) in existing pipe erected concealed in

wall/ceiling complete.Cat.III

[248] Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 29.00 Pt. 425.21

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories.[I] For 6A Plug and 6 a

switch with 2-1.5 sq.mm Cu. Wire from nearby switchboard/mcb

db board.(j) in existing pipe erected concealed in wall/ceiling

complete.Cat.III

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[249] Point wiring for Individual Plug with & earth wire of 1.5 sq.mm 22.00 Pt. 567.62

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of

pipe erected complete with Modular type switch & 5 pin Plug

erected on PVC / Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories.(j) in existing pipe

erected concealed in wall/ceiling complete.[II] For 16A Plug and

16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db

[250] Point wiring for on board Looped Plug with 6A Modular type 193.00 Pt. 257.55

switch & 5 pin socket erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured / metallic/white

front plate modules erected on / in wall / ceiling with following

type accessories.Cat.III

[251] Providing following type of Modular Type Accessories mounted 26.00 Each 160.59

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge.(3) Two Pin/RJ-11 Telephone Socket.[A] For

One Gang. Cat.III

[252] Providing following type of Modular Type Accessories mounted 218.00 Each 25.25

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge.(7) Blank Plate Single cat-III

[253] Providing following type of Modular Type Accessories mounted 130.00 Each 160.59

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge.(8) Computer RJ-45 socket.Cat.III

[254] Providing following type of Modular Type Accessories mounted 22.00 Each 199.98

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge.(10) 6/16Amp. Universal socket cat-III

[255] Providing following type of Modular Type Accessories mounted 22.00 Each 410.06

with PVC / metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate , modules

erected with necessary connections as per site situation directed

by Engineer In charge.(14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double

Pole Modular MCB Switch.Cat.III

[256] Providing and erecting ISI mark Medium class RIGID PVC PIPES of 13157.00 Rmt 24.24

following size complete to be erected on/in wall or ceiling erected

with necessary PVC fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in approved manner

as directed (a)20 mm

[257] Providing and erecting ISI mark Medium class RIGID PVC PIPES of 1056.00 Rmt 33.33

following size complete to be erected on/in wall or ceiling erected

with necessary PVC fittings & Junction boxes fixed with adhesive

solution & Clamps with following dia of pipes, in approved manner

as directed(b) 25 mm

[258] Providing & erecting PVC Corrugated Flexible Conduit with 100.00 Rmt 21.21

required nos. of coupling, PVC bushes, Check-nuts etc. complete of

following sizes.(2) 25 mm.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[259] Supplying under floor pregalvanised corrosion proof rectangular 382.00 Rmt 458.54

sheet steel cable trunking of 1.6 mm thick having with stand point

load up to 1.33 Ton & free from seepage of concrete of screed

water with all accessories,Junction Box,Joints as required and

demanded by engineer-incharge and laying/erecting as per OEM

guidelines and as per instruction of engineer incharge having

following size of dimensions and No of compartments (W x D x T)

Cat-III.[3] 100mm x 25mm x 1.6 mm with one compartment.

[260] Supplying under floor pregalvanised corrosion proof rectangular 204.00 Rmt 1224.12

sheet steel cable trunking of 1.6 mm thick having with stand point

load up to 1.33 Ton & free from seepage of concrete of screed

water with all accessories,Junction Box,Joints as required and

demanded by engineer-incharge and laying/erecting as per OEM

guidelines and as per instruction of engineer incharge having

following size of dimensions and No of compartments (W x D x T)

Cat-III.[6] 300mm x 25mm x 1.6 mm with Three Compartments.

[261] Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated 5490.00 Rmt 62.62

ISI marked stranded Copper conductor wire in following type of

pipe to be erected concealed in /flushed on wall/ceiling, with

sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size.(E) in existing

pipe.(b) 2 wire 2.5 sq. mm

[262] providing and erecting Mains with 1.1 KV grade FRLS PVC insulated 200.00 Rmt 86.86

ISI marked stranded Copper conductor wire in following type of

pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size.(E) in existing pipe.(a) 2 wire 4 sq.

[263] providing and erecting Mains with 1.1 KV grade FRLS PVC insulated 730.00 Rmt 240.38

ISI marked stranded Copper conductor wire in following type of

pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for

earth continuity of following size.(E) in existing pipe.(h) 4 wire 6 sq.

[264] providing and erecting Mains with ISI marked, 1.5KV grade 32.00 Rmt 56.56

electrolyte multi stranded, annealed copper conductor with heat

resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.(e) One wire 6.00 sq.

[265] providing and erecting Mains with ISI marked, 1.5KV grade 96.00 Rmt 91.91

electrolyte multi stranded, annealed copper conductor with heat

resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.(f) One wire

[266] providing and erecting Mains with ISI marked, 1.5KV grade 48.00 Rmt 300.98

electrolyte multi stranded, annealed copper conductor with heat

resistant PVC insulated conforms to IS 694, IEC - 227 erected in

existing pipe of following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring) with required

size of copper lugs, nuts and bolts if required.(i) One wire

[267] Supplying and erecting Flexible PVC insulated multistrand 120.00 Rmt 22.22

multicore 1.1 kv grade ISI marked copper wires of following size to

be erected as directed.(c) 1.00 Sq.mm 2 core round/ flat PVC

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[268] Supplying and erecting Flexible PVC insulated multistrand 140.00 Rmt 46.46

multicore 1.1 kv grade ISI marked copper wires of following size to

be erected as directed. e) 1.50 Sq.mm 3 core round PVC sheathed

[269] Providing & Erecting approved make following size of TV Co-axial 120.00 Rmt 62.62

flexible cable comprising inner conductor of solid bare copper

insulated with Foam PE & Secondary conductor made of poly -

Aluminium film bonded Al. Braids @ suitable coverage overall

sheathed with black PVC insulation.(e) RG-11.

[270] Supplying & erecting approved make Telephone Cable electrolytic 1328.00 Rmt 20.20

copper conductor PE insulation twisted in two pairs, & wrapped

with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer

Jacket suitable for telephone wiring & confirming to C-DOT erected

in existing pipe. of following size of conductors & nos.of pairs.

With necessary connections.[A] Conductor Size 0.5 mm .(a)

Unarmoured.(2) Two Pairs.

[271] Supplying & erecting approved make Telephone Cable electrolytic 220.00 Rmt 199.98

copper conductor PE insulation twisted in two pairs, & wrapped

with FRLS PVC tape & sheathed with FRLS PVC or HFFR outer

Jacket suitable for telephone wiring & confirming to C-DOT erected

in existing pipe. of following size of conductors & nos.of pairs.

With necessary connections.[A] Conductor Size 0.5 mm .(b)

Armoured [Jelly Filled].(2) Twenty Pairs.

[272] Supplying & erecting approved make LAN cable of following size in 7248.00 Rmt 47.47

existing pipe as per direction.[C] CAT -

[273] Providing & erecting main Distribution (MDF) indoor type, back 2.00 Each 1368.55

mounted frame as per DoT standard approved with krone

strips.(b) Suitable for 20 pair.

[274] Providing & Erecting 3mm thick acrylic Sheet with grooving as 2000.00 Sq. Inch. 3.03

[275] Providing & erecting Switch board for Computer or electric 130.00 Each 1133.22

apparatus consisting of following modular type accessories

mounted with PVC / Metallic concealed/open box with single

mounting base frame covered with textured/metallic /white front

plate,modules erected with necessary connections as directed.1

no. 6A/16A universal plug-switch combined.3 nos. 6A Switch.3

nos. 6A 5 pin Plug.For Modular Type Accessories.Cat.III

[276] Decorative call bell Ting-tong box type 250 volts complete erected 26.00 Each 71.71

[277] Supplying & erecting Electronic Type Cordless Call Bell erected on 5.00 Each 250.48

PVC/Metal board having portable bell push working on D.C. & bell

on 230V A.C. supply with cells / battery

[278] Supply of Fibreglass Step (A Type) Ladder - 6 FT having following 1.00 Each 13940.02

specifications :It should have nonconductive Structural moulded

top, with Slots to keep tools close at hand, inside Spreader Braces,

Aluminium Feet with thick rubber tread, nonconductive Full

channel Fibreglass and two pairs of gusset support at the bottom

step. All gussets are heavy duty steel.Capacity : 300 lbs. Step Size :

3” Width : 23” “Approx. Spread : 41” Approx.Wt. : 11 Kg

Approx. Cube : 6.2’

[279] Supply of Fibreglass Step (A Type) Ladder - 10 FT having following 1.00 Each 22342.21

specifications :It should have nonconductive Structural moulded

top, with Slots to keep tools close at hand, inside Spreader Braces,

Aluminium Feet with thick rubber tread, nonconductive Full

channel Fibreglass, two pairs of gusset support at the bottom step

and All gussets are heavy duty steel.Capacity : 300 lbs. Step Size :

3”.Width : 29” Approx. Spread : 66”Approx. Wt. : 19 Kg Approx.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[280] Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 20.00 Each 238.36

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name

160V to 270V, Power Factor more than 0.95, THD < 15%,CCT

K to 6500K,Luminaire efficacy> 85 lumens/watt,LED driver

efficiency > 85 %,(fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)(A) Tube Light

with integral driver.(ii) 12-14 Watts, Surge-2 KV, IP-20,

conventional 4 feet.Cat.III

[281] Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 63.00 Each 373.70

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name

160V to 270V, Power Factor more than 0.95, THD < 15%,CCT

K to 6500K,Luminaire efficacy> 85 lumens/watt,LED driver

efficiency > 85 %,(fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)(A) Tube Light

with integral driver.(iv) 22-24 Watts, Surge - 2KV,IP-20,

conventional 4 feet.Cat.III

[282] Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 16.00 Each 589.84

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in aluminium

casted body with company mark/name 160V to 270V,Power Factor

more than 0.95, THD < 15 %,CCT 3000 K to 6500K,Luminaire

efficacy> 85 lumens/watt ,LED driver efficiency > 85 %,( fitting

required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the

ranges shown.)(A) Square/ Circular shaped Surface/Recessed

Mount Downlight with provision for spring loaded mounting clips

complete.IP20.(iii) 16-20 watts, Surge-2 KV.Cat.III

[283] Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 536.00 Each 758.51

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in aluminium

casted body with company mark/name 160V to 270V,Power Factor

more than 0.95, THD < 15 %,CCT 3000 K to 6500K,Luminaire

efficacy> 85 lumens/watt ,LED driver efficiency > 85 %,( fitting

required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the

ranges shown.)(A) Square/ Circular shaped Surface/Recessed

Mount Downlight with provision for spring loaded mounting clips

complete.IP20.(iv) 22-24 watts, Surge-2 KV.Cat.III

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[284] Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 22.00 Each 1794.77

Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high

U.V. & corrosion resistance with diffuser housed in aluminium

casted body with company mark/name 160V to 270V,Power Factor

more than 0.95, THD < 15 %,CCT 3000 K to 6500K,Luminaire

efficacy> 85 lumens/watt ,LED driver efficiency > 85 %,( fitting

required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the

ranges shown.)(B) LED Panel Light with provision for Plane front

frame with translucent cover fixed to housing complete.IP20.(vi)

36 watts, 24" x 24", Surge- 2KV.Cat.III

[285] Supplying and erecting LED street light / Flood light fittings with 28.00 Each 3345.12

High power White LEDs wattage of 3 Watt and above assembled

on single MCPCB, efficiency more than 130 lm/w and corrosion

free High pressure die cast aluminum housing with smooth finish

powder coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt

. LED driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)(A) Street Light

(IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection.(i) 48 watts.Cat.III

[286] (B) Flood Light (IP-65), Surge protection -4KV integral and ,Light 4.00 Each 7266.95

must have 440VAC line supply with over-voltage protection.(iv)

above 90 to 120 watts.Cat.III

[287] Providing and erecting Approved make Four pole moulded case 7.00 Each 6173.12

circuit breaker having breaking capacity ICU of 25 KA. at

V,having normal current rating up to 25 A to 100A. with Fixed

thermal & magnetic release suitable to work on A.C. supply 50 c/s.

with all internal connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.ICS=100% of ICU only.Cat III

[288] Providing and erecting Approved make Four pole moulded case 2.00 Each 8861.34

circuit breaker having breaking capacity ICU of 35 KA. at 415 V.

having normal current rating 125A. with Fixed thermal & magnetic

release suitable to work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected with

enclouser 16 G.M.S. housing.ICS=100% of ICU only.Cat III

[289] Providing and erecting Approved make Four pole moulded case 2.00 Each 8055.76

circuit breaker having breaking capacity ICU of 35 KA. at 415 V.

having normal current rating 125A. with Fixed thermal & magnetic

release suitable to work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected in

existing 16 G.M.S. housing.ICS=100% of ICU only.Cat III

[290] providing and erecting Approved make Earth fault Relay suitable 4.00 Each 4983.34

to mount with inter connection suitable to following size of

moulded case circuit breaker having CT ratio & MCCB rating as

following along with shunt trip 220V AC. with all internal

connections & complete erected in existing M.S.housing.(2) 125 A -

200 A , CT Ratio 1/200.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[291] providing and erecting Approved make Earth fault Relay suitable 2.00 Each 4687.41

to mount with inter connection suitable to following size of

moulded case circuit breaker having CT ratio & MCCB rating as

following along with shunt trip 220V AC. with all internal

connections & complete erected in existing M.S.housing.(1) 15 A -

100 A , CT Ratio 1/100.

[292] Supplying and erecting triple pole & neutral 440V / 500V panel 3.50 Rmt 3202.71

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating

tape for phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with necessary

connections.(B) Suitable for 200 Amp. capacity.

[293] providing and erecting Miniature circuit breaker single pole 0.5A to 32.00 Each 270.68

2A system and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark.Cat.III

[294] Providing and Erecting Miniature circuit breaker single pole 6A to 288.00 Each 112.11

25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark cat-III

[295] Providing & erecting 240 V MCB double pole switch for motor & 21.00 Each 299.97

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity.(A)

[296] Providing & erecting 415 V MCB Four Pole for Motor & Inductive 3.00 Each 595.90

Load (C Curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity.(A) 32 Amp.Cat.III

[297] Providing & erecting 415 V MCB Four Pole for Motor & Inductive 47.00 Each 737.30

Load (C Curve) having 10KA breaking capacity & confirms to IS

:8828 in existing box having following capacity.(C) 63 Amp.Cat.III

[298] Providing and erecting Two way Centre off Four pole MCB Change 1.00 Each 852.44

Over Switch (IS 13947-3 / IEC 60947-3) in existing box.(a) for

[299] Providing and erecting Sheet Steel powder coated MCB 1.00 Each 2016.77

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The

DBs should be used of same company of MCB to be used) suitable

for.(A) single phase incoming and horizontal single phase

outgoing(b) sheet steel double door (IP-43)(v)16 way.(Concealed)

[300] Providing and erecting Sheet Steel powder coated MCB 2.00 Each 2806.99

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The

DBs should be used of same company of MCB to be used) suitable

for.(B) three phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI).(b) sheet steel double

door.(i) 4 way.(Concealed)

[301] Providing and erecting Sheet Steel powder coated MCB 16.00 Each 3496.62

distribution board - flush / surface mounted fitted with busbar,

neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The

DBs should be used of same company of MCB to be used) suitable

for.(B) three phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI).(b) sheet steel double

door.(ii) 6 way.(Concealed)

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[302] Providing and erecting Sheet Steel powder coated Vertical MCB 1.00 Each 12181.61

distribution board (VTPN) - flush / surface mounted double door

(IP54) fitted with insulated copper busbar, isolated neutral link,

earth bar and DIN rail, confirming to IS 13032 and BS 5486-1986,IP-

54 suitable for 63/100 AMP TPN MCCB + RCCB as incomer and

three phase outgoing as per following .(The DBs should be used of

same company of MCB to be used) (B)6 way outgoing

[303] providing and erecting Approved make RCCBs conforming to IS: 56.00 Each 2235.13

12640 and having sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on single phase

V,50Hz. having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic component.

for following Max. rating erected as directed.(ii) 40 Amps.

[304] Providing and erecting Approved make RCCBs conforming to IS: 1.00 Each 2637.11

12640 and having sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on 3 phase and

neutral 415V,50Hz. having characteristic of quick action & tripping

with all advance feature & do not incorporate any electronic

component for following Max. rating erected as directed.(ii)

40Amps. FP.Cat.III

[305] Providing and erecting Annealed bare Copper wire 8 SWG. 15.00 Kg 794.87

[306] Providing and erecting required size Copper strip for earthing of 12.00 Kg 794.87

H.T. OCB / ACB/ Transformer, LT panel board, Motors etc. using

[307] Supplying & erecting earth pit of minimum bore dia.150mm size 10.00 Each 4591.46

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make OEM has to

submit test certificate including value of earth resistance of

installation duly stamped and signed by agency and officer

Incharge has to ensure the value of earthing resistane mentioned

in test Certificate) & having back filling compound of (B) Inner

chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as

per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. (a) For

Electrical Installation up to 440V in normal soil,Length of pipe -

Mtr,Back filling compound - 1 Nos Bag of 15 Kg..

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[308] Providing & erecting weather proof, dust & vermin proof, floor 5.78 Sqm 14889.66

mounted front operated indoor type cubical panel board

necessary IP-42 and above protection as per approval from

engineer incharge made from 14 SWG thick CRC M.S. sheet for

outer body & doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling, welding, riveting with

internal partitions & cable alley as per requirements & instruction

of engineer-in-charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting PVC copper wire /

copper-aluminium strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of hinged

doors, handles with locking arrangement and rubber gasket,heavy

duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted

with epoxy powder coating.(The rates excludes the cost of

switchgears, bus bars, inter connecting mains & Copper Aluminium

strips, meters, Fuses etc. The dimension shall be measured

excluding base beams) The panel shall be supplied with following

approved manufacturers with following size.(B) The standard

companies switch gear shall be used and only manufacturers at

CPRI approved factory .(i) with 350mm depth .

[309] Providing , erecting , fabricating the M.S. structure as per 100.00 Kg 77.77

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections complete with

cutting, welding, grinding & finishing duly painted with one coat of

red oxide with erection on site as per direction of engineer in

charge with necessary grouting, cementing, plastering & finishing

[310] Supplying & erecting approved make Four Pole 415V Motorised 2.00 Each 45374.25

Automatic transfer switch including controller with UV/OV, phase

sequence, single phasing and frequency protection interior for

panel mounting with operating mechanism A.C.23A duty

confirming to IS for (C ) 125A.Cat-lll

[311] Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper 30.00 Rmt 289.87

cable 1.1 KV grade to be erected as directed of following size. (D)

core 2.5 sq.mm.

[312] Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 100.00 Rmt 220.18

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size

of cables.(B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

[313] Providing and erecting XLPE(IS:7098)(I)-88-FRLS ISI armoured cable 30.00 Rmt 378.75

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size

of cables.(D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core).

[314] Providing and erecting XLPE(IS:7098)(I)-88-FRLS ISI armoured cable 480.00 Rmt 540.35

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size

of cables.(F) 3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core).

[315] Providing and erecting XLPE(IS:7098)(I)-88-FRLS ISI armoured cable 30.00 Rmt 1168.57

multistrand Aluminium conductor for 1.1 KV. to be laid on wall

with necessary clamps or in existing trench / pipe of following size

of cables.(I) 3 1/2 core 240 Sq. mm( 120 Sq. mm 1/2 core).

[316] Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 590.00 Rmt 126.25

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe of following

size of cables (b) 4 core 6 Sq. mm

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[317] Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 70.00 Rmt 987.78

multistrand Copper conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe at road crossing or

floor of following size of cables.(B) 4 core 16 Sq. mm

[318] Making trench in soft soil of suitable width of 90 cm deep for 610.00 Rmt 55.55

laying cable or locating the fault all over the run and back filling

the same and making the surface as normal ground.

[319] Supplying following size of Light duty “A” Class G.I . Pipe & 25.00 Rmt 300.98

erecting as directed by Engineer-in-charge. (B) 50 mm dia

[320] Supplying following size of Light duty “A” Class G.I . Pipe & 25.00 Rmt 696.90

erecting as directed by Engineer-in-charge.(D) 100 mm dia.

[321] Providing & laying approved make Double walled corrugated 40.00 Rmt 62.62

pipes (DWC) of polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same material at required

depth in existing trench for laying of cable. below ground / road

surface for enclosing cable.(A)50 mm outer dia.

[322] Providing & laying approved make ISI marked HDPE 6Kg / cm2 500.00 Rmt 163.62

(Class-3) as per IS:4984:1995 PE-80 to be erected at road crossing

on or floor as directed for laying of cable. The pipes as following

size of dia & weight per 6 mtr.(B) 50 mm inner Dia.

[323] Providing & laying approved make ISI marked HDPE 6Kg / cm2 360.00 Rmt 491.87

(Class-3) as per IS:4984:1995 PE-80 to be erected at road crossing

on or floor as directed for laying of cable. The pipes as following

size of dia & weight per 6 mtr.(E) 90 mm inner Dia.

[324] Providing and, fixing heavy duty flange type brass cable gland with 6.00 Each 47.47

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.(D) 2 to

[325] Providing and, fixing heavy duty flange type brass cable gland with 9.00 Each 38.38

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.(B) 2 to

[326] Providing and, fixing heavy duty flange type brass double 3.00 Each 75.75

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

for following size of cables.(B) 3 & 1/2 core 35/50 Sq. mm.

[327] Providing and, fixing heavy duty flange type brass double 2.00 Each 103.02

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

for following size of cables(C) 3 & 1/2 core 70 Sq. mm

[328] Providing and, fixing heavy duty flange type brass double 13.00 Each 140.39

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

for following size of cables(E) 3 & 1/2 core 120 Sq. mm

[329] Providing and, fixing heavy duty flange type brass double 2.00 Each 247.45

compression type cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails, insulating tape etc

for following size of cables(H) 3 & 1/2 core 240 Sq. mm

[330] Solderless crimping type Aluminium lugs conforming to IS suitable 197.00 Each 6.06

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

[331] Solderless crimping type Aluminium lugs conforming to IS suitable 2.00 Each 15.15

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner.(C) 16/25 Sq.mm.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[332] Solderless crimping type Aluminium lugs conforming to IS suitable 11.00 Each 20.20

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner(D) 35/50 Sq.mm.

[333] Solderless crimping type Aluminium lugs conforming to IS suitable 19.00 Each 25.25

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner(E) 70 Sq.mm.

[334] Solderless crimping type Aluminium lugs conforming to IS suitable 41.00 Each 45.45

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner(G) 120 Sq.mm.

[335] Solderless crimping type Aluminium lugs conforming to IS suitable 6.00 Each 85.85

for cable of following size evenly crimped with high pressure tool

& connected to switchgear terminals with brass/cadmium plated

nut bolts in an approved manner(J) 240 Sq.mm.

[336] Solder less crimping type Copper lugs conforming to IS suitable for 8.00 Each 12.12

cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner.(C) 16 Sq.mm.

[337] Providing & erecting Approved make Power Saving 50 Watt Ceiling 227.00 Each 1948.29

Fan with double ball bearing ISI mark with Condenser 230 volt A.C.

50 Hz 1200 mm sweep complete having 3blades with aluminium

blades with , canopy & 30 cm. down rod erected with earthing.

[338] Supplying and erecting 19 / 20 mm. nominal bore Medium Class 227.00 Rmt 108.07

M.S. Pipe down rod erected duly painted for fan complete with

proper insulation without leakage and earthing.

[339] Supplying & erecting fan hook box of 10 mm M.S. round bar 227.00 Each 108.07

bounded to the RCC bars up to 50mm length each side and pierced

through a 16 Gauge M.S. box / Heavy Duty PVC box complete

erected concealed in Ceiling with necessary finishing.

[340] Providing 2.5mm.thick laminated acrylic sheet to cover the fan 227.00 Each 18.18

hook or Fan box.

[341] Supplying & erecting approved make low noise decorative exhaust 30.00 Each 1366.53

fan having square frame ABS body with inbuilt lowers & square

frame.250mm with 1350 RPM Cat.II

[342] Supplying and erecting approved make oscillating type bracket fan 16.00 Each 2534.09

A.C. 23OV. 50cy/s 400/450 mm sweep wall mounted with height

adjustment and rotary tilting device complete with guard, flexible

Core plug top complete erected with lead wires as directed.Cat.II

[343] Supplying and erecting approved make Octagonal pole made from 20.00 Each 6874.06

HR sheet steel. The pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/2633/4759, suitable

suspend local wind speed with integral Junction box consist of

terminal plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With Suitable

foundation (Included) as per details given by manufacturer

considering site requirement.(C) 5 Mtr. Long 70 mm Top X

mm bottom dia, 3 mm thickness with 200mmX200mmX12mm

base plate, 4-M16 Bolts and 600mm long with necessary G.I. J

Bolts .Approx Pole weight 46 kg.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[344] Supplying & erecting approved make SMC press moulded 4.00 Each 898.90

composite FRP. loop-in, loop-out approx. 2mm thick box complete

with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting

mob & hinged doors as per requirement having locking

arrangements with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps& earth bolt of

following size of box.(A) 300mm x 200mm x 100mm [deep].

[345] Providing and erecting street light pole bracket comprising main B 12.00 Each 561.56

Class MS pipe of 4.2 cm/require outside dia. complete with

suitable B Class M.S. sleeve tubing of approx. 45cms.length and

suitable for 76.5 mm / 80mm. / require size pole top having

sufficient fasteners for fixing the brackets and having spread of

mtr. length with suitable rise as per site condition & suitable

welded stiffener reducer and nipple with check nut complete

painted with one coat of Red oxide / PU base primer and two coats

of Aluminium / PU paint. paint with following nos of arms.[A]

Single Arm bracket 1 Mtr

[346] Providing and erecting street light pole bracket comprising main B 8.00 Each 758.51

Class MS pipe of 4.2 cm/require outside dia. complete with

suitable B Class M.S. sleeve tubing of approx. 45cms.length and

suitable for 76.5 mm / 80mm. / require size pole top having

sufficient fasteners for fixing the brackets and having spread of

mtr. length with suitable rise as per site condition & suitable

welded stiffener reducer and nipple with check nut complete

painted with one coat of Red oxide / PU base primer and two coats

of Aluminium / PU paint. paint with following nos of arms.[B]

Double Arm Bracket 1 Mtr.

[347] Supplying & erecting approved make Digital time switch having 1.00 Each 3168.37

lithium cell 6 years operative and operate battery backup

channel day clock with 14 memory programme, suitable to

operate on 240V + 5%, 16A with, floating contacts Minimum

switching setup time 1 minimum & LCD display. Also comprised

permanent ON/OFF switching. Programming switches & housed in

fire proof thermoplastic enclosure & transparent cover erected as

required with necessary connection erected as directed.

[348] Supplying & erecting power contactor ,AC3 duty for time switch 1.00 Each 2782.55

complete erected as per direction. [D] 4 pole 440V 40 Amp. Cat III

[349] SITC of Digital / PCM / TDM EPABX System having SMT design, 2.00 Each 77077.14

system with flexible universal slots. Inbuilt Auto attendant facility,

Minimum 15 Nos. conference, Analog extension line, Calling GSM,

E&M line, PRI / EI & VOIP program me through Analog telephone

digital key from Ethernet, public address cord, shall have

unrestricted simultaneous dialing facility,QSIG protocol on PRI,

/ STD / ISD / Local-Locking, Class of Service, Quick Dial-Single Digit

dialing of any two external number, Once only ring device,

Chairman / Secretary - Do not disturb Facility, Power Down Mode,

Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call Back,

Barge-in, Call Pick Up & Call Transfer, Call transfer while Ringing

with Voice Guide System, (DISA), Caller ID (CLI), CLI Base ECF, CLI

Base routing Internet Ready Port, External Music Port, Call

Budgeting, Call Most Calculation (ASMDR), DID Direct Inverse

Dialing, External Music Input, Fax Homing, Global Directory

Printing with following capacities [[Approved by Competent

Authority i.e. not Below the rank of Executive Engineer ][C] No of

Extension 48, No of Junctions 9, 8 Port IP Resource in-built, 4 Port

Web base Video Conferencing, No of expandable ports :

Operators Console - 01 Compatible : ISDN.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[350] Supplying & erecting push button type telephone instrument 26.00 Each 565.60

having speaker phone Caller ID & hands free dialing system &

memories with display system Single line [[Approved by

Competent Authority i.e. not Below the rank of Executive Engineer

[351] Providing and erecting Inverter based approved make Cassette 10.00 Each 80731.32

type split air-conditioning unit consisting of condensing unit with

fan motor, hermetically sealed scroll/rotary compressor with

accessories etc. duly connected separately erected evaporating

unit and blower motor with its accessories by Eco friendly Green

gas charging & Internal copper wiring & Remote control ( 3 star

and above of current year) with necessary core cutting.(B) for

[352] Supplying and erecting insulated pair of soft copper tubing open or 180.00 Rmt 965.56

concealed including power and control cable,necessary PVC drain

pipes for Split AC machine up to 4 TR capacity

[353] Providing & erecting water cooler having storage capacity 150 Ltr. 4.00 Each 55893.40

& cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C.

The outlet temp. of the water should drop by 15˚C within a hour,

The water cooler should be comprising of hermetically sealed

compressor, fan motor, condensing unit, water tank surrounded

by evaporating, coil, thermostats, relay etc.complete with

necessary inlet & outlet connection. The body of water cooler will

be made from Stainless Steel.

[354] Supplying & erecting 5 stage single reverse osmosis water 4.00 Each 29187.99

purification system with M.S. powder coated frame, prefilter

housing with 'O' ring presediment filter GAC filter, carbon filter

suitable buster DC pump capacity 80 psi, mention with 40 psi inline

type post carbon filter auto low & high pressure switches with

following size of storage tank & LPH capacity & erected as

directed.[C] 50 Ltr / Hr with 150 psi 2 nos booster pump

[355] Supply and Erecting of Static Stabilizer suitable for following 10.00 Each 4029.90

capacity of A.C Machine the Stabilizer Must have Minimum

Technical Specification are Input working Single Phase Voltage

Range Up to 150V-280V.50Hz, Output Voltage Range Up to 200V-

240V,50Hz,Autoreset Facility,LED Display for Indicating

Voltage,Spike/Surge Protection,Time Delay Facility,Proper Wall

Mount Facility with Required Accessries & on site 3 year

Replacement/Repairing Warranty.(2) For 2 Ton Thermal Overload

Protection 15 Amp.

[356] Supplying and erecting approved make panel mounting type 4.00 Each 1275.63

Digital Voltmeter having 3 digits LED display, 0 to 750 AC Volts

range erected on existing panel board with all connection, wiring

etc .with manufacturers calibration certificate.

[357] Supplying and erecting approved make panel mounting type 4.00 Each 1558.43

Digital Ammeter having 3 digits LED display, external CT operated,

calibrated for 0 to 1000 Amps suitable to operate on 500 Volt AC

erected on existing panel board with all connection, wiring etc

.with manufacturers calibration certificate.

[358] Supplying and erecting Ammeter / Voltmeter selector switch for 3 8.00 Each 317.14

phase AC Supply 500 V on existing panel board with necessary

[359] Providing & erecting L.T. Current Transformer with bar primary 12.00 Each 274.72

50/5 to 1000/5 ratio 15 VA burden erected in existing CRCA box

duly secured with insulating materials connected to the meter

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[360] Supplying and erecting approved make suitable panel indicator 12.00 Each 43.43

LED type lamp, lens cover, complete erected with necessary

[361] Providing & erecting open well horizontal mono block pump set 2.00 Each 18746.61

with cast iron body, complete for three phase submersible motor

having.[D] For 5 HP 3 phase open well horizontal mono block

pump set suitable for 1350 LPM to 310 LPM @ 10 to 42 Mtr head

suitable for 50/65 mm dia delivery pipe.Cat.II

[362] Supplying & erecting approved make motor control cubical panel 2.00 Each 7722.46

(Direct - on - line) made from 16 G. CRCA sheet duly epoxy powder

painted inside and outside with hinged doors and locking,

arrangement consisting of suitable size of ON- OFF isolator (AC -

3/23duty) main fuses, single phasing preventer, indicating lamps

for R- Y - B phases, overload relay, Automatic water level

controller, Ammeter, Voltmeter each with two way selector

switch incoming, wires duly socket crimped, main contactor &

overload relay, start - stop push buttons, to be erected on angle

iron frame grouted on wall as directed. The isolator, overload relay

& contactors will be of L & T, Siemens or BCH make only. (A) DOL

[363] Supplying & erecting approved make 3 phase motor control 1.00 Each 13605.71

cubical panel ( Star - Delta) made from16 G. CRCA sheet duly

painted with epoxy powder painted inside and outside with hinged

doors and locking arrangement, consisting of suitable size of ON-

OFF isolator (AC - 3/23 duty) main fuses, single phasing preventer

cum water level. Guard (Complete unit), Toggle switch to by pass

Single phase preventer cum WLG, indicating lamps for R- Y- B

phases, over load relay, Automatic water level controller,

Ammeter & Voltmeter each with two way selector switch incoming

wires duly socket Crimped, Panel to be erected on angle iron

frame grouted on wall as directed. Star Delta & main contactor,

overload relay, thermal / Electronic Star delta cutoff timer, start -

stop push buttons. The isolator overload relay & contactors of L&

T, Siemens or Cuttler Hamer make only. Panel to be erected on

angle iron frame ground on wall.(B) S/D up to 10 H.P.

[364] S.I.T.C. submersible pump set suitable for bore of 150 mm. dia. or 1.00 Each 35590.38

more having three phase motor capacity not more than 7.5 H.P.

with following capacity . Lifting and Lowering taken extra.(A) (12

stage) 280 to 240 LPM discharge at 90 to 104 mtrs. head

respectively suitable for 50mm dia. delivery pipe.Cat.III

[365] Lowering of submersible motor pump set at the depth of following 2.00 Job 856.48

,complete with required. Nos. and size of casing pipes erected by

means of proper chain pulley block & pipe wrenches after

checking of threads of each pipe with coupling to take the load of

the pump set and pipe assembly filled up with water.(d)For Open

well Horizontal submersible pump set for sump well. (i) 1 HP to

[366] Lowering of submersible motor pump set at the depth of following 1.00 Job 2568.43

,complete with required. Nos. and size of casing pipes erected by

means of proper chain pulley block & pipe wrenches after

checking of threads of each pipe with coupling to take the load of

the pump set and pipe assembly filled up with water.(B)Above

mtrs. and Up to 120 mtrs. .

[367] Providing and erecting ISI marked PVC insulated PVC Sheathed 30.00 Rmt 146.45

Flat flexible Submersible copper cable approved make of

following Size.(C) 3 Core x 4 Sq. mm.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[368] Providing and erecting ISI marked PVC insulated PVC Sheathed 100.00 Rmt 172.71

Flat flexible Submersible copper cable approved make of

following Size.(D) 3 Core x 6 Sq. mm.

[369] Providing Water proof straight Joint in PVC insulated flat flexible 4.00 Each 189.88

copper cable by using insulating material, water proofing material,

& making the joint complete. (A) Up to 10Sq. mm

[370] Supplying of following size of HEAVY UPVC column pipe with 80.00 Rmt 493.89

coupler and wire lock.[C] 65 mm dia.

[371] Supply of following size of TOP & BOTTOM accessories i.e. Adaptor 1.00 Per set 1900.82

set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer -

in - charge with necessary plumbing as desired.[E] 65 mm dia

[372] Supplying and erecting, commissioning and testing of Diesel 1.00 Each 1590065.22

Generating set confirming to IS: 4722:1968 & BS:5514 having

continuous rating, 3 phase, 415 volts, 50 cycles A.C. supply

comprising of a totally enclosed air/water cooled diesel engine

with multi-cylinders developing suitable BHP not less than

following capacity at 1500 RPM with 10% overload for one hour in

24 hours with standard accessories like fly wheel, lubricating oil

cooler, "A" class governor, heavy duty fuel wheel and lubricating

oil filter, oil bath air filler, lubricating oil pressure gauge, end

exhaust manifold, standard set of tools with adjustable spanners,

screw drivers, cylinder head to cover, joint cylinder head to

exhaust, element lube oil filter, 12 / 24 volts electric starting

equipment complete with standard heavy duty battery, dynamo,

cut-outs, ammeter, necessary wiring, pressure gauge, starter etc

and heavy duty Residential type exhaust silencer (With DEF

System) and vertical hot air duct both logged with asbestos rope,

save oil trays, exhaust piping of required length, standard

wall/floor mounted fuel with level indicator and piping and drip

proof alternator, self excited, self regulated, screen protected,

with excitation system, capable of delivering the rated system

output at 415 volts, 3 phase, 0.8 PF, 50 Hz, 4 wire, running at

RPM, conforming to IS-4722- 1968 with voltage regulation +/-

5% of rated voltage from no load to full load. Both the engine and

alternator fitted on a common fabricated steel base plate with

antivibration mounting engine

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

and alternator both connected to each other by flexible flange

coupling and with floor/wall mounted control panel box

comprising of voltmeter ammeter, selector switches, ACB / MCCB

/ MCB of adequate capacity, indicator lamps duly wired with HRC

fuses. The alternator & control panel shall be connected with

provided suitable capacity armoured cable and complete with

Acoustic enclosure (canopy) made out of 16 SWG CRCA Sheet,

sound absorbing material Rockwool of 64 density & 100 mm thick

conforming to IS:8183 / PU Foam of 40 Density - at least 40 mm.

The resin bonded rockwool covered from inside the canopy by

perforated sheet with 3/4 mm holes, sound level not more than

dB at a distance of 1 mtr, as per PVCT norms.DG set should have in

built fuel tank capacity of minimum 8 hrs of continous running

capacity on full load . Erection, commissioning and satisfactory

testing as per requirement with first filling of fuel (minimum up to

the 80% of fuel tank capacity), oil, etc. with guarantee /

Warrantee of complete system for Two years. & with obtaining all

necessary certificate from Electrical Inspector. The Capacity and

Ratings of DG sets are as below. (As per new CPCB4+ Emission

norms Engine With - Turbo Charger, EGR (Exhaust Gas

Recirculation), CRS (Common Rail Fuel System), DOC (Diesel

Oxidation Catalyst), SCR (Selective Catalytic Reduction), Integrated

wiring harness connected to ECU .) (Q) Continuous rating of

KVA ,BHP not less than 254 BHP

[373] Providing & erecting approved make AMF control panel suitable 1.00 Each 222714.09

for following size of 3 phase, 415 V., 50 cycles, A.C. diesel

generating set complete of scope as detailed below:1) Power

module: A pair of electromechanically interlocked contactors (for

mains & generator) Overload relay for generator contactor

Neutral contactor for mains and generator Power socket for

connections. 2) Control and metering module: Line voltage

monitor. Generator voltage monitor Ammeter 3 items attempt

start facility. Air circuit breakers/MCB/MCCB of suitable rating for

auto/manual operation. Auto/manual switch. Emergency stop

push buttons. Manual start push button. frequency meter. Engine

hour meter. Two earthing studs.3) Protection module: The engine

shutdown in the unlikely event of Low lube oil pressure High

cylinder head temperature. V belt failure.4) Indicators with alarm

Load on generator.5) Indicators Load on mains Engine fails to start

. Emergency stop battery charger.The AMF Panel of following

capacity.(D) AMF Control Panel for200 KVA/250 KVA3 phase DG

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[374] Design, Supplying, installing, testing of factory fabricated ready 2.00 Each 142942.27

made Three phase APFC Panel Cubical Panel fabrication should be

type tested as per IEC 61921, 61439:1&2 Capacitor Duty Contactor

for switching as per following Steps Incomer Switch of MCCB type

Icu=Ics=50KA at 400/440 Volts, with OC, SC, internal earth fault

protection Incomer Switch of MCCB type Icu=Ics=50KA at 400/440

Volts, with OC, SC, internal earth fault protection,Copper tinned

insulated Busbar,Cubical panel should be indoor type with IP

and IK 10,Metalized polypropylene film tye3-phase 550Volt

Capacitor,De tuning Reactor for each capacitor,Panel having Short

Circuit and Overload protection,Each step Capacitor having

suitable MCB with Sc, OL, internal earth fault relay,Each stage

having Stage Contactor (Capacitor load rating),PF regulator master

controller having suitable steps with LCD display, Rs

Communication port, Indication LED Lamps for main incomer and

ON-OFF for each capacitor bank,MS Chanel for Floor mounting,

Cable entry as per site situation,Cooling fans for panel.(A)50 KVAR .

[375] SITC of Vertical Air Termination Solid aluminium with Base- 10 mm 7.00 Each 9416.23

dia and 1000 mm long. Air Termination Base tested for

conditioning, Ageing Test & Lightning impulse current withstand

test: 100 kA of 10/350µs waveform in an accredited Third party

laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol with

MAST 34mm dia 3000 mm long- Cold Galvanized

[376] SITC of 8 mm dia solid Aluminium Conductor for roof top mesh 340.00 Rmt 299.97

grid and tested as per IEC 62561- 2 conducted in the Govt.

accredited thirty party laboratory to meet the requirement of

IS/IEC 62305 with Required Accessories - Aluminium Holding clamp

at every 1 mtr distance, Aluminium/SS cross splicer at every

crossing of Alu. conductor, Expansion piece with connectors at

every 20 mtr distance, Aluminium straight Splicer to connect

conductors. All Accessories should be tested as per IEC 62561-1

2018 Cl. 6.3 for conditioning & Ageing Test & 6.4 for Lightning

impulse current withstand test: 100 kA of 10/350µs

waveform(Ageing & Electrical test ) conducted in a sequence

manner & tested in the Govt. accredited Third party laboratory to

meet the requirements of IS/IEC

[377] SITC of Galvanized Steel Flat 25x6 mm thickness from earth 35.00 Rmt 154.53

electrode directly in ground as required. Zinc coating: 500 g/m

square (Approx:70 micron coating) tested and used exclusively for

lightning protection earthing system and ring equipotential

[378] SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel 7.00 Set 5992.33

electrode with 250 micron copper bonding & 1 bag of Carbon fill

Based environment friendly backfill tested as per IEC 62561-7 in

NABL accredited Laboratory and suitable stainless Steel double

sided clamp. Eco Friendly rust proof heavy duty weather proof

Polyethylene Earth Pit Chamber with following dimensions :254

mm dia (top), 330 mm dia (bottom) & 260 mm (height).

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[379] Supplying, Erecting, Testing & Commissioning the passenger / 1.00 Each 2123933.04

stretcher lift having following main features:[1] GEAR LESS LIFT

DRIVE (MRL) comprising of High Starting torque Lift 3 phase 440 V

A. C. Permanent Magnet Synchronous motor of proper rating with

high efficiency shall be used.[2] Micro processor based / PLC,

ACVVVF, vector control drive with encoder feedback closed loop

system shall be used for lift car and door operation which shall be

full collective selective operation hall call demand response,

UP/DOWN hall stops, Main, Up/ Down Contactor with overload

and phase reversal relay and safety controls.[3] Car with M S

platform with bracings of adequate size and to sustain the impact

load cabin + passenger with safety factor of fire for steel and side

panels of Stainless steel of sheet of grade 304 duty. Car ceiling will

be S.S. finishes with aesthetic appearance with LED ceiling lights.

Car flooring shall be of s/s 304 chaker plate design sugeested of

engineer in charge. of engineer in charge. Car doors shall be of

stainless steel grade 304, hairline finish with centre opening /

telescopic automatic doors. Car panel will also be S.S. 304 finished

with emergency stop device, mechanical door safety device,

facility of auto/ attended mode. All car panel buttons and all floor

switches must be with brail language as per lift act.[4] All landing

doors must be fire rated for 2 hour shall be fully automatic centre

opening/ telescopic opening made of hairline finish steel grade of

304 with key holes and infrared curtains with Unlocking facility

[5] Appropriate battery operated emergency light in the car along

with alarm switch shall be provided. Also, Emergency Light & Fan

should start immediately without any Time Delay as soon as power

fails.[6] Digital scrolling indicator system for up-down arrow along

with floor position indicator shall be provided inside the car and at

all floors.[7] Full height infra red curtain with multiple cross /

crossing light beams shall be provided.[8] Automatic Rescue

Device (ARD) shall be provided accordingly of passenger capacity

with Manual Rescue Operation ( Manual Cranking Facility). [9]

Audio visual indication in the lift car showing over loading shall be

provided such that doors kept open till excess load is removed.[10]

Spring buffers/PU Buffers shall be provided.[11] Car fan as per

passenger capacity with automatic sleep timer shall be

provided.[12] Voice annunciator with suitable music shall be

provided in lift car.[13] Self diagnostics system for operational and

safety parameters shall be provided in control panel.[14]

Mechanical over speed governor with governor calibration as per

actual site parameters and submission of calibration certificate

submission, door key holes in the floor doors, fireman switch shall

be provided.[15] Lift machine hoisting arrangement in the lift

machine room and monkey ladder for lift pit should be provided

by the lift agency, along with the other steel structure works,

foundations for the machine etc.[16] In the hoist way fascia plate

shall be provided without any extra cost, where ever required as /

if directed by engineer in charge.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[17] Permanent wiring with necessary safety devices like RCCB in

all circuit, Over Voltage Under Voltage protection and THD

eliminator in circuit for lift machine room and lift well with proper

numbers of light points, with fixtures, exhaust fan and plug points

shall be provided by the agency. Only 3 phase Power Supply shall

be made available by department in lift machine room. Necessary

Earthing as per Lift Act/Rules shall be arranged by Lift Agency.[18]

Any civil/ electrical works for additional and alteration in lift shaft

and machine room related to erection of lift shall be made by lift

agency without any extra cost. (granite/marble fixing around all

landing door openings are not in lift agency’s scope.)[19] Agency

has to provide all working drawings and documents and liaison

services for obtaining all necessary permission from lift inspector

and other authorities.[20] acrylic transparent licence/display A4

size holder in lift car.[20A] As per statutory requirement of Govt.

Of Gujarat lift & escalator act 2000, lift agency has to provide.1.

Car top safety barricade.2. Push & talk communication system.3.

Fireman's switch operation at Ground Floor. 4.carrying out third

party lift inspection during/after lift erection and provide report by

third party authorized by concern licensing authority .5.agency

has to provide third party insurance upto completion of free

maintenance period and submit the document for the same.[21]

Car Panel Operating Buttons with floor position indicator/buttons

must be of Auto Glow type clearly visible when view from inside

22] For Physically Handicapped person Full Length Handrails of

hairline finish steel grade of 304 should be provided at appropriate

height on the Rear & Side Wall Panels in Lift Car. [23] With

Necessary KVA rating voltage controlled Stabilizer suitable for your

controller, drive and all equipments of lift.[24] Necessary rating of

DP Elcb and FP Elcb required for lift is in scope of work which

rating is sugested by CEICED Department (electrical Inspector).20

passengers .1. Advanced control system dual 64 bit embedded

microprocessor with CANBUS Serial Communication mode

including Regenerative power efficient operation,on site

programming facility, Anti nuisance, Pte-opening, BMS/RMS with

necessary online real time monitoring system having necessary

connectivity for remote monitoring & other suitable supporting

hardware & software devices to fulfil the purpose.2. Floor

Indication LCD Display with call registration & brail mark with

arrival gong and hall lantern & TFT Screen in the car with MP3

Voice Announcer.3. CAR Panel should be Scratch resistive SS

Moonrock finish / Hair Line / Honeycomb for car and all Doors, All

landing doors must have fire rating up to 2 hours and car door

must have multi-level crisscross beam door protection.4. To & fro

communication system & wiring (i.e. car , control room & guard

room ) and Each elevator are equipped with remote monitoring

system.agency has to provide mobile app and user id and

password for monitoring.

(BB) Ground plus 3 upper floors with Rated Speed of 1.0 m/sec

with micro price/PLC control and ACVVVF. drive.(C) With General

PLUS ADDITIONAL SPECIAL FEATURES attached herewith. Prem.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[380] Supply, Installation, Testing & Commissioning of following size of 68.00 Kw. 40658.56

Grid Tied Solar Power Plant with Solar Panels (ALMM approved):

Frame Material : Anodized Aluminum alloy Frame With Twin Wall

Profile, Front Cover : High Transmission Low-Iron Tempered Glass

(AR Coated), High efficency and positive power tolerance Pmax:

0/+5, Module Efficiency should be approx. 19.5%-22%, Normal

operating temperature 45'C, Junction Box with Waterproof IP67 &

MC4 Compatible and Enclosed with Bypass diodes, 100%

Electroluminescence test to ensure error free Modules, Thep.

temp. co-efficient of the PV module shall equal or better than -

0.45%/degree C. Solar PV modules of minimum fill factor 75% to

be used. Unit Production:- More than 4.5 Unit /kw /day

(Actual)(1Year Avg) With 10 year Product warranty and 25 year

Linear Power Warranty includes all mechanical and electrical

parameters of the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of AC to DC is

5:6 for the Installation capacity which are given in AC KW.Solar

Inverter: MPPT Range: MPPT Range: 80-1000 V , Max efficiency:

97.5% - 98.9%, O/p Frequency: 50/60Hz, Operating Altitude (m)

≤4000, O/p Power Factor: ~1, O/P THDi: <3%, Operating

Tempreture Range: -25~60°C, Integrated protection of Inverter are

Anti-islanding Protection, Input Reverse Polarity Protection,

Insulation Resistor Detection, Ground fault protection, Residual

Current Monitoring Unit, Output Over Current Protection, Output

Short Circuit Protection, Output Over Voltage Protection,

PV array string fault Protection. Protection Degree: IP65, User

Interface LCD & APP, Datalogger & Communication: GPRS / Wi-

Fi.Integrated, Input Reverse Polarity Protection Integrated,

Insulation Resistor Detection Integrated, Residual Current

Monitoring Unit Integrated, Output Over Current Protection

Integrated, Output Short Circuit Protection Integrated, Output

Over Voltage Protection Integrated, Protection Degree: IP65, User

Interface LCD & APP,Datalogger & Communication: GPRS / Wi-Fi,

Module Mounting Structure: The mounting (Rectangular pipe /

square pipe / circular pipe) with requisite cross bars, nuts and

bolts, etc. shall be Hot deep galvanized with minimum 80micron

coating. The Rectangular / square /circular hollow pipe section

used for the structure should have a minimum thickness of

mm. other than above, the material thickness should be minimum

2.5 mm. A certificate of a structural engineer certifying the

strength and stability of the mounting structure to withstand the

weight and wind speed of 150 km/hour throughout the life span of

25 years of the system, shall be submitted by the vendors. Hot

Dipped Galvanized steel coils. suitable arrangement for base plate

for foundation , solar panel mounting, the structure should be

suitable for carry the load of solar panel,wiring, sprinkler system

etc. with necessary foundation work/wall mount,j bolt, anchor

fastner etc. the nut bolt used for installtion of stucture should be

(SS 304) quality.

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

The ground clearance of the bottom most edge of solar panel shall

not be less than 300 mm to 1200 mm or as per site’s

technical/feasibility requirement.

a. Column –The minimum section (thickness) should be

b. Rafter - The minimum section (thickness) should be

c. Purlin - The minimum section (thickness) should be 40MM *

40MM Balane of System with necessary Swichgears (Suitabel size

and protection of ACDB & DCDB), inter connecting wiring, earthing

system as per the CEIG drawing approval, lightining arrester

system as per the CEIG drawing approval, all liasoning work with

various gov. dipartment like state nodal agency,DISCOM & CEIG is

included in agency scope.(Excluding All charges namely GEDA

Application fees, Solar connectivity Charges, Meter connectivity

Charges, Meter testing Charges and system stability/strenthning

charges.) (E) Grid Tied Solar Power System: 51 - 100 kW (3 - phase).

[381] Providing & erecting, programming, testing of Ahuja make Model 2.00 Each 8670.85

No. CMC-5100 or equivalent make and model chairman unit with

gooseneck condenser microphone with flexible stem of 470 mm in

length and light indicator on mike for visual indication,One

headphone output,attractive design with die cast aluminium base

for stability ,priority button for chairman microphone,built in

volume control for head phones,chime tone facility to precede

chairman priority calls,microphone on/off button,red indicates for

microphone is active,microphone with -63dBV/mbar,(7.5mV/Pa).

[382] SITC of Ahuja make Model No. CMC-5200 or equivalent make and 40.00 Each 8058.79

model delegate unit with gooseneck condenser microphone with

flexible stem of 470 mm in length and light indicator on mike for

visual indication,One headphone output,attractive design with die

cast aluminium base for stability ,built in volume control for head

phones,microphone on/off button,red indicates for microphone is

active,microphone with -63dBV/mbar,(7.5mV/Pa).

[383] SITC of Ahuja make Model No. CMA-5400 or equivalent make and 2.00 Each 22952.25

model central mixture amplifier with power handling capacity of

50 watt (RMS) at 2% THD,90W Max,three micro phone inputs and

1 Auxiliary,frequency response 60 Hz to 14000 Hz (+/-3 dB),S/N

Ratio > 60 db, USB Volume control, Bass and treble control,master

colume control, MP3 Digital recorder, Headphone stereo jack

socket,LED Level indicator,with speaker terminal block (4,8,16

Rate (Exclusive

Item Description of Item (with brief specification and reference GST)

Quantity Unit Amount

No. to book of specifications)

[384] SITC of Ahuja make Model No.PS-300TM or equivalent make and 16.00 Each 1642.36

model wall mounted speaker with power handling capacity of

watt (RMS)/15w Max.,100V,Power Tap on 6/3/10.5w,low

impedance 8Ohm,Frequency response 150-20000 Hz,SPL

86dB,Woofer 75mm(3"),tweeter 31mm(1.22"),with necessary

Nine Crore Fifty One Lakh Seventeen Thousand Two Hundred Two Rupees and Eighty Four Paisa Only

I/We am/are willing to carry out the work at…………………………………………….% above/below percent (Should be written in figures and words)

of the estimated rate mentioned above. Amount of my / our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct…………………………% below Add…………………………% Above

In Worlds In Worlds

(* Please strike out whichever is not applicable).

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-Charge for which

no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-10/2017 Cement

Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there is a change as per actual mix design

the cost of difference of cement consumption have been deducted from the rate of original item at the rate of input rate

mentioned in all the tender.

5. Credit of dismantled materials of amount of Rs. 74590.00/- must be recovered from contractor's 1st R.A. bill.

6. All duties, taxes, and other levies except GST payable by the contractor under the contract, or for any other cause shall be included

in the rates, prices and total Bid Price submitted by the Bidder. (GST will be paid extra)

Dated Signature of Dy. Executive Engineer Executive Engineer

the Contractor. R & B Sub Division R & B Division