Construction Work Of Pump House, Toilet Block And SITC Of VT Pumping Machinary, As Per Location Chart, At. Jetpur-Navagadh Under 15th Finance Grant (Tide) Year-2024-25/2025-26.

NAME OF WORK:- CONSTRUCTION WORK OF PUMP HOUSE, TOILET BLOCK AND SITC OF VT PUMPING

MACHINARY, AS PER LOCATION CHART, AT. JETPUR-NAVAGADH

TOTAL AMOUNT PUT TO TENDER

TOTAL AMOUNT PUT TO TENDER

PERCENTAGE RATE TENDER

Sr.No. Schedule Amount

1 Schedule - "B"- 1

2 Schedule - "B"- 2

3 Schedule - "B"- 3

4 Schedule - "B"- 4

Total Amount Rs.

Total Amount Rs.

I/We am/are willing to carry out the work @ ________% Above / Below_____________Percentage (should be writen in

figures and words) of the Estimated rates mentioned above amount of my / our Tender works out as under.

Estimated Amount Estimated Amount

Put to Tender Rs. 1,87,35,819=00 Put to Tender Rs. 1,87,35,819=00

Add …………………….% Rs. Deduct …………………….% Rs.

Total Rs. Total Rs.

(In Words (In Words

Stamp with Signature of Contractor

Cons. Engineer Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: 15TH FINANCE GRANT (TIDE) YEAR-2024-25/2025-26

NAME OF WORK :- Providing, Supplying, Installation, Testing & Commissioning of VT Pumping Machinery with

co-ordinate Mechanical & Electrical Accessories

Location :- Amarnagar Road Main HW For Ujadpa ESR, At- Jetpur

SCHEDULE - "B-1"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

MECHANICAL SECTION

Supply, installation, testing & commissioning of Vertical Turbine pump

motor set of specified duty parameters & guaranteed efficiency of

following MOC with specified capacity vertical solid shaft TEFC squirrel

cage induction motor (with minimum IE-3 efficiency class), working on

three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed

1000 RPM along with column and bowl assembly, discharge head, base

channel / RSJ etc. complete as per relevant IS. M.O.C.: Impeller &

Sealing Rings: CF8M, Bowl & Suction Bell: Cast Steel WCB , Shaft with

coupling: SS 410, Column Pipe: MS ERW, Mechanical seal (above

kw),Base Plate: MS, Line Bearing: Thordon, Suction Strainer: S.S..

Capacity:- 148 LPS x 60 Mtr. head (1450 RPM) with min. prime mover of

125 KW x 3 sets (2W + 1S) =375 KW

Erection Charges for Motor rating (without material supply) 76.0 KW to

Supply at Site, Storage, Erection, Installation, Testing & commissioning

of MS 300 MM Ø 5.6mm thick Delivery piping with Suction Strainer,

Flanges, Bolts, Nuts, and Pipings with Y-Tee Connection Flanges,

Concentric / Eccentric / Nozzles etc. Complete. As per.Is Standared etc

Supply at Site, Storage, Erection, Installation, Testing & commissioning

of MS - 450 mm Ø 6.3mm Thick Common Header Pipings with Y-Tee

Connection, Flanges, Bolts, Nuts Piping etc. Complete as per relevent

IS Standard & requirement. 40.00 5500.00 Rmt

Supply at Site, Storage, Erection, Installation, Testing & commissioning

of M.S 100 mm Ø By pass Pipings with Y-Tee Connection, Flanges,

Bolts, Nuts etc. Complete as per relevent IS Standard & requirement 30.00 109.36 Kg

Manufacture, Supply Delivery And Fixing of MS Flange socket spigot

bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with M.S.Pipes manufactured

delivery of specials is to be made to GWSSB store or site of works any

where in Gujarat including all taxes, liading, unloading, carting, stacking,

insurance, inspection charges, octroi etc. complete. (MS Specials

Flange Ended) 300.00 109.36 Kg

Supply at site, storage, Erection, installation, testing & commissioning of

300 mm Ø Both End Flanged Butterfly Valve as per IS 13095 with

sleeve of EPDM & disc, shaft & internal parts of SS-410, with ISI mark of

PN 1.6 Rating to be installed on Delivery Pipe complete as per

specifications & requirement. 3.00 18251.00 No

Supply at Site, Storage, Erection, Installation, Testing & Commissioning

of 450 mm Ø with Both End Flanged Butterfly Valve For Header PN

Rating and ISI mark of IS 13095 with sleeve of EPDM & disc, shaft &

internal parts od SS - 410 & with ISI Mark only as per technical

specification & requirement. 1.00 37016.00 No

Supply at site, storage, Erection, installation, testing & commissioning of

300 mm Ø C.I. D/F reflux valve on Delivery pipe confirming to relevent

standard with PN 1.6 rating etc. Complete as per specifications.

Supply at site, Storage,Erection, Installation, Testing & Commissioning

of Both End Flanged 100 mm Ø C.I. Non Rising Spindle Type Sluice

Valve of PN 1.6 with hand / wheel cap opereted (pd type short body)

Rating etc. Complete (For Air valve on Header Pipings & Bypass piping)

as per relavant Std.& Specification With ISI Mark Only 1.00 4037.00 No

Supply at site, Storage, Erection, Installation, Testing & commissioning

of DS 2 Type 100 mm Ø Air Double Acting Valve on Header Pipings as

per relavant Std. with Approved make etc. Complete as per

Specification. 1.00 5793.00 No

Supply at Site, Storage, Erection, Installation, Testing & Commissioning

of flange ends Expansion Bellow as per EJMA standards of overall

length of minimum 300 mm, designed for 15 mm axial compression and

5 mm axial extension with tie rods etc. of following MOC & pressure

ratings. MOC: Bellows: SA 240 Gr. 304; Internal Sleeve: SA 240 Gr.

304; Weldends: IS 2062 Gr. B; Flanges: IS 2062 Gr. B (Drilling as per IS

1538 /IS 6392 ) & Limit Rods & Nuts: CS - IS 1367 for Common Delivery

Piping 300 mm Ø PN 1.6 3.00 10800.00 No

Supply at Site, Storage, Erection, Installation, Testing & Commissioning

of flange ends Expansion Bellow as per EJMA standards of overall

length of minimum 300 mm, designed for 15 mm axial compression and

5 mm axial extension with tie rods etc. of following MOC & pressure

ratings. MOC: Bellows: SA 240 Gr. 304; Internal Sleeve: SA 240 Gr.

304; Weldends: IS 2062 Gr. B; Flanges: IS 2062 Gr. B (Drilling as per IS

1538 /IS 6392 ) & Limit Rods & Nuts: CS - IS 1367 for Header Piping

Design, Supply, Installation, Testing, Commissioning of Bourdon Type

Pressure Gauge, ±1% accuracy, Direct bottom 1/2" NPT (M) process

connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type

Bezel, SS316 L Bourdon Tube, SS 316 Movement material, Aluminium

dial with black graduation on white background, Micro Zero adjustable

pointer, neoprene gasket, Blow out disc, shatter proof glass, SS tag

plate etc as per IS 3624. 100MM dia dial size (i) 0 to 10 kg/cm² 3.00 1029.00 No

Providing & Laying Reinforced Cement Concrete in Thrust Block / Piping

/ Valves Supports etc. with TMT steel, Black Trap Kapchi as Coarse

Aggreate for Raft,Grillage Footing with Necessary Centering Form work,

Consolidating as per Directive in 1:2:4 Ratio comp. as per site

requriement 5.00 8566.40 Cumt

ELECTRICAL SECTION

S.I.T.C. of LV MCC Panel totally enclosed, dust & bermin proof, indoor

type, minimum degree of protection - IP 52 as per IS: 2147, operation on

3- Phase, 4 Wire, 415V, 50Hz, Neutral effectively grounded, with

instrumentation compartments accomodating LED type indicating lamps,

control contactors as per IS: 13947, CT of accuracy class- I as per IS:

2705, relays, meters & control MCBs, air insulated electrolitic grade

Aluminum busbar for three phase & neutral system with incomming

breaker- microprocessor based Air Circuit Breakers (electrically

operated drawout type)/ air break fixed type MCCB with trip free

mechanism, current limiting type as per IS: 8828, Motor Contractor (as

per type -2 coordination),

Overload Relay with built-in single phasing prevention feature & auxiliary

feeders as per SLD drawings, momentary contact type push buttons,

equipment fittings, bus bars, cable boxes, cable gland, incoming &

ougoing cable connection for 1100V grade, Aluminium/ Copper

conductor XLPE/ PVC insulated & PVC sheathed armoured cable, 10%

spare terminals, power wiring using 1100V grade, FRLS insulated

copper conductor wires conforming to IS: 694 & 8130, cable

compartments/ alleys of minimum 300mm size, GI earth bus bar for

entire length. MCC shall be fabricated from cold rolled, coled annealed

(CRCA) sheet steel & minimum thickness of various members shall be

as follows: Base Frame/ Channel/ Gland Plate - 3 mm, Load Bearing

Members/ Doors - 2 mm and Internal Partitions - 1.6 mm. Auto

Transformer Starter with MCCB, Contactor, O/L relay, cast resin type

CT, Digital MFM, Analogue Ammeter, SPP, Timer etc. (Size 2700mm(w)

x 600mm(d) x 2175mm(h)) of 90KW = 1 Working Feeder + 1 Extra

Feeder 1.00 607095.00 No

Supply, laying, testing & commissioning of 1.1 kV grade, XLPE

insulated, stranded Copper conductor, galvanised steel flat strip / round

wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to

be laid on wall surface with necessary clamps / in existing cable trench /

cable trays / conduit / pipe sleeves at road crossing or floor as per site

requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) etc.

comp. with reqd. accessories.

Size : 1x3x400 Sq.mm.

(From Main Supply To SFU & MCC panel Board) 30.00 7099.00 Rmt

Supply, laying, testing & commissioning of 1.1 kV grade, XLPE

insulated, stranded Copper conductor, galvanised steel flat strip / round

wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to

be laid on wall surface with necessary clamps / in existing cable trench /

cable trays / conduit / pipe sleeves at road crossing or floor as per site

requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) etc.

comp. with reqd. accessories.

Size : 1x3x240 Sq.mm.

(Panel Board to Motar) 60.00 4973.00 Rmt

Supply & laying GI perforated type cable trays with returned edge/

flange, fabricated from 2.0 mm thick sheet steel in the standard length of

2.5 mtrs, duly hot dipped galvanized after fabrication as per IS 2629-

1989 / IS 4759-1984 including accessories such as coupler plates/ fish

plates, bends, tees, reducers, elbows, covers and electro-galvanized

hardware etc, erected on existing support as per specification and

instruction of engineer in charge.

Size:- 100mm(W) x 35mm(H) x 2mm Thick 25.00 228.00 Rmt

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe

dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm

with constant ohmic value surrounded by highly conductive compound

with high charge dissipation suitable for following type of applications.

(b) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Supply, installation, testing & commissioning single girder type fully

electrically operated EOT crane with electrically operated hoist, class II

duty, geared travelling trolley with seven meter lift complete with long

travel rail track (40 mm sq. bar), moving or cross girder, all three

motions electrically operated by suitable rating motor IP 54, control

panel & down pendant control block, brake, safety device, cables form

motor to starter panel & other required accessories & tested as per IS

Specifications.

5 Tonne capacity, 9m.-12m. span, 12m. long travel, 12m.-10m. lift 1.00 626250.00 Set

Flow Meter Monitoring Device

Providing supplying and Installation of IOT Based Smart Wireless Flow

monitoring System including all type of Hardware, Software and allied

work. The system shall include remote data access at user end by GSM

on either Android or IOS device. The device API should be available so

that the data could be integrated with the Dashboard to be provided to

Nagarpalika employees that can be seen on any Android or iOS device.

Supplying 4 mm rubber matting of following thickness as per

IS:15652/IEC 61111 (for LT Panel) 6.00 1017.00 Sq.Mtr.

Cable Glands: Providing & fitting heavy duty brass cable glands (nickel-

plated) with washers & rubber ring conforming to IS, suitable for 3, 3½ &

4 corecables of following type & sizes: Double Compression Brass

Cable Glands 240 Sqmm 3 to 3½ 18.00 720.00 Each

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections & complete

erected in existing 16 G.M.S.housing with specification ICS=100% of

ICU only Cat III. 1.00 16061.00 No

Busbar with JunctionBox:

providing and erecting sandwitched type bus duct having following

specification : Sandwich type busbar for use as Feeder Busbar for

interconnection between separate electrical equipment/ load centers,

and for use as Plug in busbar risers. The busbar shall be suitable for

operation in a 690V / 1000 V system with frequency of 50 Hz.

(A) Aluminium BusBar with 400 A Capacity 2.00 8314.00 No

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: 15TH FINANCE GRANT (TIDE) YEAR-2024-25/2025-26

NAME OF WORK :- Providing, Supplying, Installation, Testing & Commissioning of VT Pumping Machinery with

co-ordinate Mechanical & Electrical Accessories

Location :- Amarnagar Road Main HW For Amarnagar Road ESR, At- Jetpur

SCHEDULE - "B-2"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

MECHANICAL SECTION

Supply, installation, testing & commissioning of Vertical Turbine pump

motor set of specified duty parameters & guaranteed efficiency of

following MOC with specified capacity vertical solid shaft TEFC squirrel

cage induction motor (with minimum IE-3 efficiency class), working on

three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed

RPM along with column and bowl assembly, discharge head, base

channel / RSJ etc. complete as per relevant IS. M.O.C.: Impeller &

Sealing Rings: CF8M, Bowl & Suction Bell: Cast Steel WCB , Shaft with

coupling: SS 410, Column Pipe: MS ERW, Mechanical seal (above

kw),Base Plate: MS, Line Bearing: Thordon, Suction Strainer: S.S..

Capacity:- 157 LPS x 40 Mtr. head (1450 RPM) with min. prime mover of

90 KW x 2 sets (1W + 1S) =180 KW

Erection Charges for Motor rating (without material supply) 76.0 KW to

Supply at Site, Storage, Erection, Installation, Testing & commissioning

of MS 300 MM Ø 5.6mm thick Delivery piping with Suction Strainer,

Flanges, Bolts, Nuts, and Pipings with Y-Tee Connection Flanges,

Concentric / Eccentric / Nozzles etc. Complete. As per.Is Standared etc

Supply at Site, Storage, Erection, Installation, Testing & commissioning

of MS - 450 mm Ø 6.3mm Thick Common Header Pipings with Y-Tee

Connection, Flanges, Bolts, Nuts Piping etc. Complete as per relevent

IS Standard & requirement. 40.00 5500.00 Rmt

Supply at Site, Storage, Erection, Installation, Testing & commissioning

of M.S 100 mm Ø By pass Pipings with Y-Tee Connection, Flanges,

Bolts, Nuts etc. Complete as per relevent IS Standard & requirement 30.00 109.36 Kg

Manufacture, Supply Delivery And Fixing of MS Flange socket spigot

bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with M.S.Pipes manufactured

delivery of specials is to be made to GWSSB store or site of works any

where in Gujarat including all taxes, liading, unloading, carting, stacking,

insurance, inspection charges, octroi etc. complete. (MS Specials Flange

Ended) 300.00 109.36 Kg

Supply at site, storage, Erection, installation, testing & commissioning of

300 mm Ø Both End Flanged Butterfly Valve as per IS 13095 with sleeve

of EPDM & disc, shaft & internal parts of SS-410, with ISI mark of PN

1.6 Rating to be installed on Delivery Pipe complete as per specifications

& requirement. 2.00 18251.00 No

Supply at Site, Storage, Erection, Installation, Testing & Commissioning

of 450 mm Ø with Both End Flanged Butterfly Valve For Header PN

Rating and ISI mark of IS 13095 with sleeve of EPDM & disc, shaft &

internal parts od SS - 410 & with ISI Mark only as per technical

specification & requirement. 1.00 37016.00 No

Supply at site, storage, Erection, installation, testing & commissioning of

300 mm Ø C.I. D/F reflux valve on Delivery pipe confirming to relevent

standard with PN 1.6 rating etc. Complete as per specifications.

Supply at site, Storage,Erection, Installation, Testing & Commissioning

of Both End Flanged 100 mm Ø C.I. Non Rising Spindle Type Sluice

Valve of PN 1.6 with hand / wheel cap opereted (pd type short body)

Rating etc. Complete (For Air valve on Header Pipings & Bypass piping)

as per relavant Std.& Specification With ISI Mark Only 1.00 4037.00 No

Supply at site, Storage, Erection, Installation, Testing & commissioning

of DS 2 Type 100 mm Ø Air Double Acting Valve on Header Pipings as

per relavant Std. with Approved make etc. Complete as per

Specification. 1.00 5793.00 No

Supply at Site, Storage, Erection, Installation, Testing & Commissioning

of flange ends Expansion Bellow as per EJMA standards of overall

length of minimum 300 mm, designed for 15 mm axial compression and

5 mm axial extension with tie rods etc. of following MOC & pressure

ratings. MOC: Bellows: SA 240 Gr. 304; Internal Sleeve: SA 240 Gr. 304;

Weldends: IS 2062 Gr. B; Flanges: IS 2062 Gr. B (Drilling as per IS

/IS 6392 ) & Limit Rods & Nuts: CS - IS 1367 for Common Delivery

Piping 300 mm Ø PN 1.6 2.00 10800.00 No

Supply at Site, Storage, Erection, Installation, Testing & Commissioning

of flange ends Expansion Bellow as per EJMA standards of overall

length of minimum 300 mm, designed for 15 mm axial compression and

5 mm axial extension with tie rods etc. of following MOC & pressure

ratings. MOC: Bellows: SA 240 Gr. 304; Internal Sleeve: SA 240 Gr. 304;

Weldends: IS 2062 Gr. B; Flanges: IS 2062 Gr. B (Drilling as per IS

/IS 6392 ) & Limit Rods & Nuts: CS - IS 1367 for Header Piping 450 mm

Design, Supply, Installation, Testing, Commissioning of Bourdon Type

Pressure Gauge, ±1% accuracy, Direct bottom 1/2" NPT (M) process

connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type

Bezel, SS316 L Bourdon Tube, SS 316 Movement material, Aluminium

dial with black graduation on white background, Micro Zero adjustable

pointer, neoprene gasket, Blow out disc, shatter proof glass, SS tag

plate etc as per IS 3624. 100MM dia dial size (i) 0 to 10 kg/cm² 2.00 1029.00 No

Providing & Laying Reinforced Cement Concrete in Thrust Block / Piping

/ Valves Supports etc. with TMT steel, Black Trap Kapchi as Coarse

Aggreate for Raft,Grillage Footing with Necessary Centering Form work,

Consolidating as per Directive in 1:2:4 Ratio comp. as per site

requriement 5.00 8566.40 Cumt

ELECTRICAL SECTION

S.I.T.C. of LV MCC Panel totally enclosed, dust & bermin proof, indoor

type, minimum degree of protection - IP 52 as per IS: 2147, operation on

3- Phase, 4 Wire, 415V, 50Hz, Neutral effectively grounded, with

instrumentation compartments accomodating LED type indicating lamps,

control contactors as per IS: 13947, CT of accuracy class- I as per IS:

2705, relays, meters & control MCBs, air insulated electrolitic grade

Aluminum busbar for three phase & neutral system with incomming

breaker- microprocessor based Air Circuit Breakers (electrically

operated drawout type)/ air break fixed type MCCB with trip free

mechanism, current limiting type as per IS: 8828, Motor Contractor (as

per type -2 coordination),

Overload Relay with built-in single phasing prevention feature & auxiliary

feeders as per SLD drawings, momentary contact type push buttons,

equipment fittings, bus bars, cable boxes, cable gland, incoming &

ougoing cable connection for 1100V grade, Aluminium/ Copper

conductor XLPE/ PVC insulated & PVC sheathed armoured cable, 10%

spare terminals, power wiring using 1100V grade, FRLS insulated

copper conductor wires conforming to IS: 694 & 8130, cable

compartments/ alleys of minimum 300mm size, GI earth bus bar for

entire length. MCC shall be fabricated from cold rolled, coled annealed

(CRCA) sheet steel & minimum thickness of various members shall be

as follows: Base Frame/ Channel/ Gland Plate - 3 mm, Load Bearing

Members/ Doors - 2 mm and Internal Partitions - 1.6 mm. Auto

Transformer Starter with MCCB, Contactor, O/L relay, cast resin type

CT, Digital MFM, Analogue Ammeter, SPP, Timer etc. (Size 2700mm(w)

x 600mm(d) x 2175mm(h)) of 90KW = 1 Working Feeder + 1 Extra

Feeder 1.00 523342.00 No

Supply, laying, testing & commissioning of 1.1 kV grade, XLPE insulated,

stranded Copper conductor, galvanised steel flat strip / round wire

armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be

laid on wall surface with necessary clamps / in existing cable trench /

cable trays / conduit / pipe sleeves at road crossing or floor as per site

requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) etc.

comp. with reqd. accessories.

Size : 1x3x400 Sq.mm.

(From Main Supply To SFU & MCC panel Board) 30.00 7099.00 Rmt

Supply, laying, testing & commissioning of 1.1 kV grade, XLPE insulated,

stranded Copper conductor, galvanised steel flat strip / round wire

armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be

laid on wall surface with necessary clamps / in existing cable trench /

cable trays / conduit / pipe sleeves at road crossing or floor as per site

requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) etc.

comp. with reqd. accessories.

Size : 1x3x150 Sq.mm.

(Panel Board to Motar) 40.00 3144.00 Rmt

Supply & laying GI perforated type cable trays with returned edge/

flange, fabricated from 2.0 mm thick sheet steel in the standard length of

2.5 mtrs, duly hot dipped galvanized after fabrication as per IS 2629-

1989 / IS 4759-1984 including accessories such as coupler plates/ fish

plates, bends, tees, reducers, elbows, covers and electro-galvanized

hardware etc, erected on existing support as per specification and

instruction of engineer in charge.

Size:- 100mm(W) x 35mm(H) x 2mm Thick 25.00 228.00 Rmt

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe

dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm

with constant ohmic value surrounded by highly conductive compound

with high charge dissipation suitable for following type of applications.

(b) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Supply, installation, testing & commissioning single girder type fully

electrically operated EOT crane with electrically operated hoist, class II

duty, geared travelling trolley with seven meter lift complete with long

travel rail track (40 mm sq. bar), moving or cross girder, all three

motions electrically operated by suitable rating motor IP 54, control panel

& down pendant control block, brake, safety device, cables form motor

to starter panel & other required accessories & tested as per IS

Specifications.

5 Tonne capacity, 9m.-12m. span, 12m. long travel, 12m.-10m. lift 1.00 626250.00 Set

Flow Meter Monitoring Device

Providing supplying and Installation of IOT Based Smart Wireless Flow

monitoring System including all type of Hardware, Software and allied

work. The system shall include remote data access at user end by GSM

on either Android or IOS device. The device API should be available so

that the data could be integrated with the Dashboard to be provided to

Nagarpalika employees that can be seen on any Android or iOS device.

Supplying 4 mm rubber matting of following thickness as per

IS:15652/IEC 61111 (for LT Panel) 6.00 1017.00 Sq.Mtr.

Cable Glands: Providing & fitting heavy duty brass cable glands (nickel-

plated) with washers & rubber ring conforming to IS, suitable for 3, 3½ &

4 corecables of following type & sizes: Double Compression Brass Cable

Glands 150 Sqmm 3 to 3½ 12.00 448.00 Each

Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal connections & complete

erected in existing 16 G.M.S.housing with specification ICS=100% of

ICU only Cat III. 1.00 16061.00 No

Busbar with JunctionBox:

providing and erecting sandwitched type bus duct having following

specification : Sandwich type busbar for use as Feeder Busbar for

interconnection between separate electrical equipment/ load centers,

and for use as Plug in busbar risers. The busbar shall be suitable for

operation in a 690V / 1000 V system with frequency of 50 Hz.

(A) Aluminium BusBar with 400 A Capacity 2.00 8314.00 No

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: 15TH FINANCE GRANT (TIDE) YEAR-2024-25/2025-26

NAME OF WORK :- CONSTRUCTION WORK OF PUMP HOUSE

Location :- Amarnagar Road HW, At- Jetpur

SCHEDULE - "B-3"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

MECHANICAL SECTION

Designing (aesthetically) and constructing RCC Frame structure of pump

room with Positive/Negative suction.

With Gantry structure

Without Gantry structure

Penel Room 8.00 X 5.00 40.00 10365.00 Sq.Mtr.

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME: 15TH FINANCE GRANT (TIDE) YEAR-2024-25/2025-26

NAME OF WORK :- CONSTRUCTION WORK OF TOILET BLOCK

Location :- Amarnagar Road HW, At- Jetpur

SCHEDULE - "B-4"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff

upto all lead. (B) Dense or Hard soil 4.75 164.82 Cumt.

Providing and laying cement concrete 1:3:6 ( 1 cement : 3 coarse sand :

6 Machine cut stone aggregate 40mm nominal size ) and curring

complete including cost of formwork in (a) Foundation and plinth

Filling in foundation and plinth with murrum or selected soil in layers of

20cm. thickness including watering, ramming and consolidating etc.

complete. 1.70 299.67 Cumt.

Providing and laying 1:3:6 (cement :3 Course sand :6 crushed stone

aggregate 20 nominal size) and curing complete including cost of form

work in (A) Wall caps/copping 0.33 4115.74 Cumt.

Providing & Laying controlled cement concrete M-250 and curing

complete including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Beam (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. Level 0.51 5692.36 Cumt.

Providing & Laying controlled cement concrete M-250 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Lintel (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. GF. Lintel 0.31 6145.85 Cumt.

Providing & Laying controlled cement concrete M-250 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Chhajja (C) Slabs,

Landings, Shelves, Balconies, Lintel, Beams, Girders and Cantilever

upto floor two level. G.F. Chhajja 0.14 6965.97 Cumt.

Providing & Laying controlled cement concrete M-250 and curing

complete Including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in Slab (C) Slabs, Landings,

Shelves, Balconies, Lintel, Beams, Girders and Cantilever upto floor two

level. G.F. Slab 0.69 4545.90 Cumt.

Providing TMT Bar FE 415 reinforcement for R.C.C. work including

bending, binding and placing in position complete upto floor two level.

White stone bela masoanry block in course in superstructure with stone

of approved quality in cement mortar 1:5 (1 cement :5 coarse sand)

including racking the joints etc. complete. 8.53 5109.37 Cumt.

Providing 15 mm thick cement plaster in single coat on fair side

brick/concrete wall for interior plastering up to floor two level finished

even and smooth in with Floating coat of neat cement. (i) cement Mortar

1:3 (1 cement : 3 Sand) 20.43 242.01 Sqmt.

Providing 10mm thick cement plaster in single coat on brick/concrete

walls for interior plastering upto floor two level and finished even and

smooth in (i) Cement mortar 1:3 (1-cement:3-sand) Extra over items

to 64 for finishing with a floating coat of neat cement slurry. 7.29 166.77 Sqmt.

20mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-

cement : 3-sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete. 48.36 330.72 Sqmt.

Providing and laying 25mm thick Black Granite stone slab flooring over

20mm (average)base of cement mortar 1:6 (1-cement : 6 coarse sand)

or L.M. 1:1.5(1- lime putty : 1.5 - coarse sand) laid and jointed with gray

cement slurry including rubbing and polishing complete. (A) 25mm thick

Block Granite 5.50 2966.37 Sqmt.

Labour Charge Full Round Edge for Granite 20.07 51.51 Rmt.

Providing throating or plaster drip and moulding to R.C.C. Chhajja. 3.36 45.10 Rmt.

Providing and laying white glazed tiles 6mm thick in flooring treads of

steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-

cement : 3-coarse sand ) finishing with flush pointing in white cement.

Providing and laying coloured glazed tiles of the size 300 mm x 200 mm

x 8 mm / 300 mm x 450 mm x 8 mm in skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement : 3 coarse sand) & jointed

with white cement slurry. 18.10 1559.10 Sqmt.

Providing and laying broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to be tempered to bring

mortar creme out upto surface using white cement including rounding

off junctions and extending them upto 15 cm along the wall,clearing

with water and oxalic acid etc. as directed. 3.40 779.70 Sqmt.

Extra for providing and mixing water proofing material in Cement

concrete in mix proportion recommended by the manufacturers. 0.61 49.16 Lir/Kg.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-

coarse sand : 4-graded stone aggregate 20mm nominal size) laid in one

layer and finished with a floating coat of neat cement. (B) 50mm thick.

Providing and fixing FRP frame size 125x65 mm and 35mm thick FRP

shutter with wood grain raised panneled design finish shutter having

extra reinforcement on sides & edges in Gel coat finish. The core of the

shutter & frame is to be filed up with injected polyurethene foam done in

situ alongwith embedded wooden pieces for stiffening & also taking

hinges & fintures. The whole FRP frame & shutter is to be water proof

weather proof, termite proof & resistance to mild acid/alkali. Rates are to

be inclusive of S.S hinges with fastener sleeve & alluminium fixtures &

fastenings. 1.60 2019.98 Sqmt.

Providing and fixing standared extruded of alluminium section of size

63.50 x 38.10 x 1.95 mm(of Jindal Section no:4605,@ Wt 1.094Kg / Rmt

with colour anodized alluminium frame with 5 mm thick transparent

bronze colour tinted float glass as details etc complete for Fix window.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm

diameter with jali of the following nominal diameter of self cleansing

design with C.I scread down or hinged grating including the cost of

cutting and making good the walls. 2.00 614.19 No.

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight.(i) Square mouth traps. (A) 100mm x

100mm size P type. 2.00 1292.19 No.

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with briocks having croshing strength not less than

35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C.

top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

thick with cement mortar 1:3 finished smooth with a floating coat of neat

cement on walls and bed concrete etc. complete.(i) Inside dimensions

455mmx 610mm and 450mm deep for single pipe line.

Providing and fixing screw down bib taps of following size.(A) Brass

screw down bib tap polished bright. (i) 15mm dia. 3.00 186.83 No.

Providing and fixing Gun metal check or non-return fullway wheel valve.

Providing and fixing Gun metal check or non-return fullway wheel valve.

Providing and fixing Urinal of approved quality including connection with

trap and with integral longitudinal flush pipe. (A) Squating plate pattern

white earthenware 550mm x 300mm. 1.00 1706.08 No.

Providing and fixing washbasin with single hole for pillar tap with C.I. or

M.S. brackets painted white including sutting holes and making good the

same but excluding fittings. (A) Vitreous China: (ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour. 1.00 1657.09 No.

Providing and fixing C.P. brass waste for washbasin or sink. (A) 32mm

Providing and fixing chromium plated brass half trun flush cock of

approved quality including fixing in pipe line etc. complete. (i) 20mm dia.

Providing and fixing C.P. brass shower rose with 15mm or 20mm inlet.

(A) 100mm dia. Each 1.00 282.16 No.

Providing erecting and fixing double coated Syntex PVC. (ISI) water

tank of required capacity each with all necessary fittings and

connection etc. complete on terrace. 1000.00 3.95 Litr.

Providing and fixing brass screw down stop tap.(C) 25mm dia. 1.00 205.83 No.

Providing and fixing wsh down water closet (European type, W.C. Pan)

with integral P or S trap including jointing the trap with soil pipe in

Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be

measured and paid for separately) (A) vitreous China Pattern :(i) in white

colour 1.00 1356.81 No.

Providing and fixing plastic seat and cover for wash down water closer

with C.P. brass hinges and rubber buffers. (B) Black plastic seal and

cover. 1.00 291.33 No.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 32mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing laying and jointing in true line and level 50mm dia. U.P.V.C.

Pipe ( SCH- 40) for cold water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the help of clamp at

every two metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

Providing, laying and jointing in true line and level 160 diametre U.P.V.C

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 160 mm diametre x 210 mm length x 196 mm heigh at

every 2000 mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent cement

including cost of all materials. 30.00 834.38 Rmt.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C

(Type B) conforming to IS 13592-1992 with one end plain and other end

socketed with rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall be jointed with

each other with rubber lubricant, pipe shall be fixed on wall using of PVC

clamp of the size 110 mm diametre x 149 mm length x 145 mm heigh at

every 2000 mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes etc. including

testing of pipes and joints and jointed with adhesive solvent cement

including cost of all materials. 20.00 918.67 Rmt.

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil,grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade

including cleaning the surface an even shade including cleanicn the

surface of all dirt, dust and other foreign matter. 34.86 96.59 Sqmt.

Wall painting (two coats) with plastic emulsion paint of approved brand

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth. 27.72 88.39 Sqmt.

Wall Primer of Approved Brand 76.08 16.52 Sqmt.

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly

brushing the surface to remove all dirt, and remains of loose powdered

materials.etc complete. 48.36 122.14 Sqmt.

(B) Providing sock pit of 5.00 Cu.M. Volume including excavating and

filling brickbats with dry masonry work at top for 45cm. height

including covering the top with stone including providing vatas in C.M.

1:3 with finishing curing etc. complete as directed. 1.00 3516.51 No.

Total Amounts Rs.......…

Total Amounts Rs.......…

12% Electrification Charge Rs.......…

Net Total Amount Rs.......…

Net Total Amount Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika