Construction of new 11 KV line on turnkey basis

Amount

Annexure-A (LABOUR CHARGES)

Cartage of ST -Pole SP-55 from store to site including Loading and unloading

Cartage of PCC Pole 8.5 mtr long from store to site including Loading and unloading

Cartage of 11 KV XLPE cable from store to site including Loading and unloading

Cartage of Small Material from Store to Site.

Excavation of earth for ST Pole SP-55 pit of size 0.9x0.6x1/6 of full length of pole for erection of pole in all type of soil including proper dressing of sides and ramming of bottom including getting out the excavated soil and disposal of surplus excavated soil as directed complete work.

Erection of Double Pole support pole ST Pole SP-55/PCC in proper level and alignment alongwith fixing of all accessories, like top channel, X-bracing & clamps as per RESSPO construction Manual.

Grouting of pole in size 0.45x0.45x1/9 of the support in CC ratio 1:4:8 (1 cement : 4 graded stone 20mm nominal size : 8 coarse sand ) block including cost of Cement,sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling as per RESSPO construction Manual.

Muffing of poles size 0.45 cm x 0.60 cm radious with cc 1:3:6 (1 cement : 3 coarse sand : 6 graded stone 10mm nominal size) block size 45cm height from ground level including cost of cement, stone and sand etc. as per direction of Engineer-In-charge.

Fabrication of M.S. Channel Angle iron after cutting in required sizes with drilling of holes upto good finish for top channel, bracing and special type bracket etc. as per RESSPO sehedule and local approved drawing.

Digging of cable Trench in size 1500 mm deep and 600 mm width and refilling of excaveted earth properly raiming and dressing etc. as per direction of Engineer-In-charge.

Laying of 11 KV cable 3x400 sq mm in cable Trench Packing under R:C Hume pipe including cable loop both end of D/P Pole section as per specification including hanging of Cable on D/P section pole stucture. as per direction of Engineer-In-charge.

Stringing & Sagging of 11 KV grade covered conductor AAAC with 55 Sqmm as per direction of Engineer-In-charge.

Earthing of supports with M.S Earth of 2.5 meter long by hammering of M.S.Rod to proper depth and connecting the earth electrode with the help of G I wire as per construction manual

Erection of F-Clamp as per direction of Engineer-In-charge.

Erection ofV-Cross arm with pin insulator as per direction of Engineer-In-charge.

Painting of Pole with angles ,Channals and claps with one coat of Red Oxide and 2 Coats of Al. Paint & 2 Strips of Flourosent alternate layers of Red & White Paint strip each 50 mm wide up to 30 cm wide above 1.5 m from the ground level all Accessories.. as per direction of Engineer-In-charge.

Supply &Fixing of chemical compound pipe earthing complete with jointing of G.I. Earth strip properly welded by electric arc. as per direction of Engineer-In-charge.

Fixing of R.C.C cable line route marker with writing painting and numbring etc. as per direction of Engineer-In-charge.

Filling and Fixing of Termination Cable termination Kit 11KV 3x400 sqmm. (O/D) as per direction of Engineer-In-charge.

Filling and Fixing of Termination Cable termination Kit 11KV 3x400 sqmm. (I/D)as per direction of Engineer-In-charge.

Filling and Fixing of Straight Through termination Kit 11KV 3x400 sqmm. as per direction of Engineer-In-charge.

Fixing of GI Pipe 150 mm along the pole for safety of cables as per direction of Engineer-In-charge.

Installation, testing & commissioning of 11 KV VCB FDR 350 MVA 400/200/5A. 110V AC as per direction of Engineer-In-charge.

Fixing, tightening and nozzaling of Stay with pole for 11KV line and stay rod on required tension as per drawing / RESSPO manual. as per direction of Engineer-In-charge.

Laying of 11 KV Cable in 1.5 mtr depth with suitable trencheless technology including laying & fixing of HDPE pipe PE 100 PN6 & having dia 150 mm conferming to IS 4984/1995 & having thickness 9.1 to 10.3mm. as per direction of Engineer-In-charge.

High pressure testing of HT line/ UG Cable as per direction of Engineer-In-charge.

Annexure-B (SUPPLY ITEMS)

Supply of 11 KV XLPE Cable 3x400 sq mm. as per UPCL specification.

Supply of Jointing Kit for 3x400 sq mm XLPE O/D as per UPCL specification.

Supply of Jointing Kit for 3x400 sq mm XLPE I/D as per UPCL specification.

Supply of 11 KV VCB FDR 350/500 MVA 400/200/5A. 110V AC as per specification of UPCL as per UPCL specification.

Supply of 11 KV class polymetric pin insulator with hardware as per UPCL specification.

Supply of 11 KV Disk insulator B&S as per UPCL specification.

Supply of 11 KV Disk fitting 45kn as per UPCL specification.

Supply of S.T. Pole SP 55 (Galvanized) as per UPCL specification.

Supply of PCC Pole 8.5mtr long as per UPCL specification.

Supply of M.S.Channel 100x50x6 as per UPCL specification.

Supply of M.S. Angle 50x50x6 as per UPCL specification.

Supply of M.S. Angle 65x65x6 as per UPCL specification.

Supply of Stay Set 16*1800 mm as per UPCL specification.

Supply of Stay Wire 7/10 SWG as per UPCL specification.

Supply of Earth Rod 20x2500mm as per UPCL specification.

Supply of Earth Wire 8 SWG as per UPCL specification.

Supply of Half RCC Hume pipe for under Base Bottam of cable 3x400 sq mm and same on top of cable 200 mm dia with colour complete

Supply of HDPE pipe PE 100 PN6 & having dia 200MM conferming to IS 4984/1995 & having thickness 9.1 to 10.3mm.

Supply of 11 KV grade covered conductor AAAC with 55 Sqmm

Supply of F bracket clamp

Supply of X arm holding clamp for PCC Pole with N&B

Supply of Stay clamp for STP SP-55 Pole with N&B

Supply of Stay clamp for PCC Pole with N&B

Supply of Insulated cable ties

Supply of GI Pipe 150 mm

Supply of G.I Earth Strip 50x6 mm

Supply of PP & clamp for ST Pole SP-55 (made of MS flat 75x10 mm) with with 65x16mm Bolt, Nut & washers duly painted by red oxide primer. The clamps should be free from any crack, welding & burrs, complete in all respect as per sample .

Supply of Bracing clamp single ended Clamps M.S. Clamps for S.P.-55 made of M.S. flat of size 65x6 mm. with 65x16mm Bolt, Nut & washers duly painted by red oxide primer. The clamps should be free from any crack, welding & burrs, complete in all respect as per sample .

Supply of Bracing clamp single ended Clamps M.S. Clamps for PCC Pole made of M.S. flat of size 65x6 mm. with 65x16mm Bolt, Nut & washers duly painted by red oxide primer. The clamps should be free from any crack, welding & burrs, complete in all respect as per sample .

Supply of F- Clamps M.S. Clamps for S.P.-55 made of M.S. flat of size 75x10 mm. with 65x16mm Bolt, Nut & washers duly painted by red oxide primer. The clamps should be free from any crack, welding & burrs, complete in all respect as per sample .

Supply of R.C.C. Cable line route marker with writing, painting and numbering ets

Supply of Nut and Bolt off size

Supply of Danger Board/ No. Plate with fixing clamps

Supply of Barbed wire

Supply of Jointing Kit for 3x400 sq mm XLPE Straight Though

RP INFRAPOWER PVT LTD

SHIV ELECTRICALS