Construction of New building for Than Industrial & Than Rural sub division office and compound wall, internal Road, yard filling, TC plinth, parking at Than Campus under Surendranagar circle

Name of work: Construction of New office building for Than-Indus. & Than-Rural sub division office, Compund wall, Internal

road and yard filling at Than campus of surendranagar division office under Surendranagar circle Office

PARTCULARS OF ITEM QTY RATE PER AMOUNT

1 Excavation for foundation up to 1.5 M. depth. Incl. sorting out and

stacking of useful materials and disposing of the excavated stuff up to 87.00 115.92 Cmt

500 meter Lead in (A) -Loose soil

2 As above but in (B)- Dense or Hard Soil

3 As above but in (C)- Hard murrum

4 As above but in (D)- Soft rock not required blasting

5 As above but in (E)- Hard rock

6 Excavation for foundation for depth from 1.5 Mt to 3 Mt. depth

including sorting out and stacking of useful materials and disposing of

the excavated stuff upto 50Mt. Lead in

(C)- Hard murrum

7 As above but in (D)- Soft rock not required blasting

8 As above but in (E)- Hard rock

9 Filling available excavated earth (excluding rock) trenches, plinth side

of foundation etc. in layer not exceeding in 20 cm. in depth

consolidating each deposited layer by ramming & watering.

10 Filling in foundation and plinth with murrum or selected soil brought

from out side with any lead in layers of 20 cm. Thickness including

watering, pnumatic ramming and consolidating etc. comp

11 Filling in plinth with sand under floor including watering, ramming,

consolidating and dressing etc. completed. 90.00 420.69 Cmt

12 Applying general insecticide pest control treatment to floors,

cupboards etc including labour material etc. complete. Using

Heptachloride 20 EC. As Per 6113_pests Consentration Weight

percent is recommended one litre chemical emulsion dillute with

liter of water will give. Total dillute concrentration will be 40 litre

inclusive of one litre chemical emulsion appication 0.5 Litre chemical /

Sqm of surface is recommended as per I.S

13 Providing and laying cement concrete 1:3:6

(1 CEMENT: 3-Coarse sand: 6 - Hand broken stone aggregate 40MM

nominal Size) and curing complete excluding the cost of formwork in.-

Foundations and plinth.

14 Providing and laying controlled cement concrete M.150 for curing

complete excluding cost of formwork and reinforcement for reinforced

concrete work in (A) Foundations, footings,Base of columns and Mass

Providing and laying controlled cement concrete M 250and curing

complete including the cost of form work and excluding reinforcement

for reinforced complete work in

15 (A) foundation footings, Base of Columns and mass concrete 104.00 5212.50 Cmt

16 (D) Columns, Pillars Posts and Struts up to floor two level. 37.00 8398.50 Cmt

17 (D) Columns, Pillars Posts and Struts above floor two level. 17.00 8437.50 Cmt

18 (D) Columns, Pillars Posts and Struts above floor three level. 7.00 8476.50 Cmt

19 (C) Beam - upto floor two level. 84.00 6562.00 Cmt

20 (C) Beam - above floor two level. 29.00 6601.00 Cmt

21 (C) Beam - above floor three level. 2.00 6640.00 Cmt

22 (C) Lintel, chhajahs, Shelvas etc. upto floor two level. 11.00 6949.50 Cmt

23 (C) Lintel, chhajahs, Shelvas etc. above floor two level. 3.00 6988.50 Cmt

24 (C) Slab, for upto floor two level. 65.00 7203.00 Cmt

25 (C) Slab, above floor two level. 54.00 7242.00 Cmt

26 (C) Slab, above floor three level. 4.00 7281.00 Cmt

27 Providing TMT Bars confirming to IS 1786 FE 500D for R.C.C. work

including bending, binding and placing in position complete up to 36250.00 75.46 Kg

floor two level

28 Providing TMT Bars confirming to IS 1786 FE 500D for R.C.C. work

including bending, binding and placing in position complete above

floor two level

29 Providing TMT Bars confirming to IS 1786 FE 500D for R.C.C. work

including bending, binding and placing in position complete above

floor three level 1400.00 77.44 Kg

30 Brickwork using common burnt Fly Ash building bricks having crushing

strength not less than 35 kg./Sq.Cm. in foundation and plinth in

Cement Mortar 1:5. (1- Cement : 5 -fine sand)

31 Brickwork using common burnt Fly Ash bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure up to floor two level. in

Cement Mortar 1:5 (1- Cement : 5 -fine sand) GF

32 Brickwork using common burnt Fly Ash bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure above floor two level. in

Cement Mortar 1:5 (1- Cement : 5 -fine sand) FF

33 Brickwork using common burnt Fly Ash bricks having crushing strength

not less than 35 kg./Sq.Cm. in Super Structure above floor three level.

in Cement Mortar 1:5 (1- Cement : 5 -fine sand) SF

34 Half Brick masonary in common burnt Fly Ash building bricks having

crushing strength not less than 35 Kg. / Sqmt. in cement mortar 1:4 (1-

Cement : 4-Coarse Sand) in above Plinth level up to floor two level. 140.00 719.57 Smt

35 Half Brick masonary in common burnt Fly Ash building bricks having

crushing strength not less than 35 Kg. / Sqmt. in cement mortar 1:4 (1-

Cement : 4-Coarse Sand) in above Plinth level above floor two level.

36 Providing 15 mm. Thick cement plaster in single coat on both sides

Brick/concrete walls for interior plastering up to floor two level and

finished even and smooth in (i) C.M.1:3 (1cement : 3 sand)- For walls

37 Providing 15 mm. Thick cement plaster in single coat on both sides

Brick/concrete walls for interior plastering above floor two level and

finished even and smooth in (i) C.M.1:3 (1cement : 3 sand)- For walls 830.00 206.81 Smt

38 Providing 15 mm. Thick cement plaster in single coat on both sides

Brick/concrete walls for interior plastering above floor three level and

finished even and smooth in (i) C.M.1:3 (1cement : 3 sand)- For walls 55.00 229.34 Smt

39 Providing 10 mm. Thick cement plaster in single coat on both sides

Brick/concrete walls for interior plastering up to floor two level and

finished even and smooth in (i) C.M.1:3 (1cement : 3 sand)- For Celling

40 Providing 10 mm. Thick cement plaster in single coat on both sides

Brick/concrete walls for interior plastering above floor two level and

finished even and smooth in (i) C.M.1:3 (1cement : 3 sand)- For Celling 340.00 161.91 Smt

41 Providing 10 mm. Thick cement plaster in single coat on both sides

Brick/concrete walls for interior plastering above floor three level and

finished even and smooth in (i) C.M.1:3 (1cement : 3 sand)- For Celling 25.00 182.55 Smt

42 20 mm. Thick sand faced cement plaster on walls up to height

meters above ground level consisting of 12 mm. Thick backing coat of

C.M. 1:3 (1 cement : 3 sand) and 8 mm. Thick finishing coat of C.M.. 1:1

(1 cement : 1 sand) etc. complete.

43 Providing and fixing MS wire mesh(Chicken mash) at every joint of

masonary and concrete or any joint for application with plastering the

surface includding fixing with surface with necessary tools & tackels 290.00 216.00 Smt

and fittings as directed by Engineer in charge.

44 Providing cement vata 10 x10 cm size quarter round in cement

concrete in C.M. 1:1 including neat cement finishing watering etc. 200.00 23.45 Rmt

45 Providing and laying Broken China Mosaic flooring for terrace using

12 mm to 20mm broken pieces of glazed tiles to be laid over cement

mortrar 1:3 to plain or slope and to be tampred to bring mortar creme

out up to surface using white cement including rounding off junctions 370.00 739.89 Smt

and extending them up to 15cm along the wall, clearing with water and

oxalic acid etc. as directed.

46 Providing and laying 24" x 24" Vitrified 8mm thick tiles flooring over

20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface or fixing on existing flooring by adhesive

materials including dismentalling of existing flooring and jointed with 520.00 1192.28 Smt

colour cement slurry including finished with flush pointing & cleaning

the surface etc. complete for Light Shade

47 Providing and laying 24" x 24" Vitrified 8mm thick tiles flooring over

20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface or fixing on existing flooring by adhesive

materials including dismentalling of existing flooring and jointed with 16.00 1277.33 Smt

colour cement slurry including finished with flush pointing & cleaning

the surface etc. complete for DARK Shade

48 Providing and laying 24" x 24" Vitrified 8mm thick tiles flooring over

20mm (Average) base of Cement Mortar 1:6 (1-Cement : 6 Coarse

Sand) on new surface or fixing on existing flooring by adhesive

materials including dismentalling of existing flooring and jointed with 16.00 1383.99 Smt

colour cement slurry including finished with flush pointing & cleaning

the surface etc. complete for Antiskit

49 Grouting the joints of flooring tiles having joints of 3mm width, using

epoxy grout mix of 0.7 kg of orgenic coated filler of desired shade (0.10

kg of hardener and 0.2 kg of resin per kg), including filling / grouting 545.00 219.30 Smt

and comlete as per direction of Engineer-in-charge.

50 Providing and laying coloured glazed tiles of the size 300mm x 200mm

x 8mm / 300mm x 450mm x 8mm in floring, skirting, risers of steps and

dedo on 10mm thick cement plaster 1:3 (1-Cement : 3-Coarse sand) &

jointed with white cement slurry.

51 Providing and laying polished kotah stone slab Flooring over 20 mm

(Average ) thick bases of cement mortar 1:6 (1- cement : 6 coarse sand

) or LM 1:1:5 (1 lime putty : 1.5 coarse sand ) laid over and jointed with

grey cement Slurry mixed with pigment to match the shade of slab

including rubbing and polishing etc. completed (A) 25mm thick

52 Providing and laying Kotah stone slab 25 MM thick in risers of steps,

tread of steps, dedo and pillars laid on 10 MM thick Cement Mortar

1:3 ( 1-Cement : 3 -Coarse sand )and jointed with grey cement slurry 88.00 1045.80 Smt

including necessary groove and rubbing etc complete

53 Providing & laying 20 to 25mm thick, both faces polished kotah stone

with all edges machine cut up to 450mm width and of required

length (only one piece to be used ) of approved quality for cupboard

shelves including fixing the same in masonry wall by cement mortar

in three sides including curing etc. complete as directed by E.I.C

54 Providing and laying Granite stone slab flooring over 20mm average

base of cement mortar 1:6 (1 cement : 6 coarse sand ) of L.M. 1:1.5 (1

lime putty : 1.5 coarse sand )and laid and jointed with gray cement

slurry including rubbing and poishing complete. (b) Granite stone 125.00 2857.59 Smt

18mm thick 1 side polished

55 Providing and laying marble stone slab in risers of steps, skirting Dedo

and pillars laid on 10mm thick cement mortar 1 : 3 (1-Cement :

coarse sand) and and jointed with gray cement slurry including rubbing 32.00 2187.67 Smt

and polishing complete. (A) Marble slab 25mm thick

56 Providing & Fixing 15 to 20 mm thick both side polished green marble

wall partitions 600mm wide & required height & all sides polished,

machine cut & of approved quality including fixing the same in wall in 5.00 1663.02 Smt

line & level etc. complete as directed by E.I.C

57 Providing Half round moulded round front edge in trade of steps

including rubbing and polishing etc. Complete

58 Providing full round moulded round front edge in trade of steps

including rubbing and polishing etc. complete

59 Providing, & fixing hot pressed phenol bonded, exterior type solid flush

door 30mm shutter made by approved brand & as per I.S.I. standard

with water resisting plywood facing and 1mm thick laminated sheet on

both side of door & teak wood leaping all-round including 100X75mm.

teak wood frame.If necessary with glass looking window with T.W.

batten and polishing /Colour. Rates are without fixtures & fastening

but with 3 NO. of 100mm. long butt or parliamentary hinges on each 18.00 3346.00 Smt

flap of double shutter & 150mm. long hinges for single shutter and

NO. of M.S. flat hold fast grouted in C.C. (1:2:4) on each side of frame,

3 coats of oil painting of approved shades make etc., complete as per

drawing & as directed by E.I.C.

60 Providing and fixing FRP frame 100X50 mm and 28 mm thick FRP

depressed pannel shutter having extra reinforcement on sides and

edges and in Gel coat finish.The core of the shutter & frame is to be

filled up with injected fire retardent grade polyurethane foam done in

situ along with embedded wooden pieces for stiffening and also for

taking hinges and all fixures. The whole FRP Frame and shutter is to be 32.00 2354.22 Smt

water proof, weather proof, termite proof and resistance to mild

acid/alkali.Rates are to be inclusive of S.S. hinges with necessary screws

and allumunium fixtures & fastening & fastener sleeve.

61 Providing and fixing 12 mm toughened glass door fixing with Ozone

make or equivalent floor spring, SS door handle, lock as per approved

design, door edge molding etc. Complete with applying designer black

out film on door with all required accessories, labour and

transportation complete as directed by engineer in charge.

62 Providing and fixing fully glazed/partly glazed Single door shutter

made, frame of 10.15cmX4.45cm aluminum section, and Shutter-Top

& vertical section of 8.5cmX4.45cm size and bottom section of

11.40X4.45cm size, using 5mm thick "TRIVENI" or HB4 plain glass

glazing deep rubber gasket with locking arrangement, all fixtures & 32.00 4081.50 Smt

fastening of anodized section with all labours & materials etc. complete

as per drawing & as directed by EIC Complete as per drawing and as

directed by E.I.C.

63 Providing and fixing fully glazed/partly glazed Double door shutter

made, frame of 10.15cmX4.45cm size aluminum section, and Shutter-

Top & vertical section of 8.5cmX4.45cm size and bottom section of

11.40X4.45cm size, using 5mm thick "TRIVENI" or HB4 plain glass

glazing deep rubber gasket with locking arrangement, all fixtures & 5.00 6353.50 Smt

fastening of anodized section with all labours & materials etc. complete

as per drawing & as directed by EIC Complete as per drawing and as

directed by E.I.C..

64 Providing and fixing window having extruded aluminum Colour

anodized section frame main outer size 63.50 x 38.10 x 1.95 mm,@ Wt

1.094 Kg / Rmt, horizontal two track member size 61.85 mm x

mm x 1.20mm @ wt.of 0.695 Kg/mt, vertical member of size 61.85 mm

x 31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with sliding shutters of

horizontal member size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt,

vertical member of size 40mm x 18mm x 1.29mm @ wt.of 0.456Kg/mt,

@ Wt. 0.457 Kg/mt with 5 mm thick transparent bronze colour tinted

float glass with powder coated aluminum fittings and fixtures and

transparent silicon sealant glass fixing to frame as per details etc

complete for window.

65 Providing and fixing standared extruded of alluminium section of size

63mm x 38.10mm x 1.2mm (Jindal Section :2434, @ Wt. 0.643 kg per

mt with colour Powder Coated alluminium frame for ventilation with 15.00 1163.92 Smt

5 mm thick frosted glass as details etc complete for Ventilation

66 Providing & fixing fittings in position Partly panel and Partly Glazed

aluminium (alloy - HE - 9 WP ) frame partition using aluminium 'c'

section in the dimensions of 23.6mmx21.8mm to be used for top,

bottom and side ends aluminium 'H' sections in the dimensions of

23.6x60mm outer dimensions to be used for intermediate support, the

vertical & horizontal members to be joined and with concealed

aluminium angle cleat panel to be made from 5 mm thick HB4 or

"Triveni" make plain glass fixed with glazing clip rubber gasket with

aluminium beeding of required size incl. all fixtures & fastenings

including providing anti glare sun control film as per drawings & details

with rubber on all four side for air tight fitting with all taxes wastage

labour etc completed as directed by E.I.C.

67 Providing & fixing MS plain grills of required pattern to wooden frames

of windows and gap filling of wall etc. with MS flats or M.S, pipes at

required spacing and frame all- round square or round bars with round

headed bolts and nuts or by screws with one coat red oxide & two coat 2210.00 108.17 Kg

of oil paint (A) plain grill

68 Applying two coats of Birla or Asian acrylic lapy (putty) & two coats of

primer of approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the surface free from 2750.00 40.19 Smt

mortar dropping and other foreign matter and sand papered smooth.

69 Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar 2010.00 78.12 Smt

droppings and other foreign matter and sand papered smooth.- in wall

70 Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

shade including throughly brushing the surface free from mortar 730.00 83.33 Smt

droppings and other foreign matter and sand papered smooth.-in

71 Providing & applying 1 coat of approved make of primer paint

including scaffolding etc., complete as directed by E.I.C.

72 Finishing Wall with Weather Proof Exterior Emulsion Paint on Wall

Surface (Two Coats) to give an required shape even shade after

thoroguhly brushing the surface to remove all dirt, and remains of

loose powdered materials etc. complete

Supply & fixing to doors & windows, ventilators, cup boards following

fixtures & fastenings of approved quality with wooden or metal screws,

nuts & bolts as directed or as per the drawing & specifications. -

73 Providing & Fixing Flat Latch ( Aluminium )

74 Providing & Fixing Handle ( Aluminium )

75 Providing & Fixing Door Stopper (Aluminium )

76 Providing & Fixing Tower Bolt (Stainless steel) - 150MM long. 15.00 50.00 No.

77 Providing & Fixing S.S best Chromium plated Aldrop - 12MM dia. &

78 Providing & Fixing S.S best Chromium plated Aldrop - 14MM dia. &

79 Providing & Fixing Brass C.P. Mortise Lock

(standard Make) with Handle of approved quality

80 Providing & Fixing MS CP door stay double leg 12.00 120.00 No.

81 Providing & Fixing of ISI approved quality hydraulic door closer as

82 Providing & Fixing readymade P.V.C. water tight storage tank made

from linear low density polyethylene & low density polyethylene LDPF

product confirming to I.S: 10146 1982 with cover including providing & 3500.00 3.91 Ltrs.

fixing one 20mm.dia. Float valve ball cock, one 2----1000 Lit.

83 Providing laying and jointing in true line and level U.P.V.C. Pipe ( SCH-

40) for cold water including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two metre C/C or

shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials....15mm dia.

84 Providing laying and jointing in true line and level U.P.V.C. Pipe ( SCH-

40) for cold water including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two metre C/C or

shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials.....25mm dia.

85 Providing laying and jointing in true line and level U.P.V.C. Pipe ( SCH-

40) for cold water including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two metre C/C or

shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials.....32mm dia.

86 Providing laying and jointing in true line and level U.P.V.C. Pipe ( SCH-

40) for cold water including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two metre C/C or

shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent,

including cost of all materials.......50mm dia

87 Providing & fixing to wall, ceiling, floor in plumb by means of GI clamps

of 18 gauge sheet with 1 to 1.5 mtrs. Distance 2.5 Kg. /cm2 working

pressure polythene pipes incl. joining with approved solution& all

fittings like bend, tee. Y bend plug bend with water tight joints ( Finolex

or equivalent for rainwater etc. - 110 mm dia

88 Providing and fixing water closet squatting orrissa pan (India type W.C.

Pan) size 580 mm integral footrest and 100 mm P or S trap and

including 25 mm dia. C.P. brass flush valve and inlet connection etc.

comp. - vitreous china long pattern white

89 Providing and fixing wsh down water closet (European type, W.C. Pan)

with integral P or S trap and PVC flushing tank cistern with fitting and

inc. plastic seat and cover with brass hinges and rubber buffersand PVC

connector, nozzle etc,including jointing the trap with soil pipe in

Cement Mortar 1:1 (1-Cement : 1-fine sand) (Seal and cover to be

measured and paid for separately)(A) vitreous China Pattern :(i) in

90 Providing and fixing colour porcelain lip shaped wall type Urinal Pan of

approved quality & make including waste coupling bens & neccessary

outlet of 25mm dia G.I. pipe connection including providing flush cock,

PVC connection etc., Complete

91 Providing and fixing best INDIAN make coloured porcelain rectangular

wash hand basin size 550 mm x v 400mm with C.I. brackets fixed in

wall including approved quality of 1 no. of brass C.P. pillar cock, With 6.00 2355.50 No.

ceramic assembly 15mm dia, bottle trap, one brass c.p. 15mm

92 Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted

white including cutting holes in walls and making good the same but

excluding fittings. (C) Vitreous China Sink.(i) 600mm x 450mm x

93 Providing & fixing PVC SWR nahni trap IS 14735 for drain - 75mm

diameterr with Jali of the following nominal diameter of self cleansinf

design with CI scread down of higed grating including the cost of

cutting and making good the walls.

94 Providing and fixing S.W Gully trap with C.I Grating brick masonary

chamber and water tight C.I cover with frame of 300MM x 300MM size

(inside) with standard weight. [I] Square mouth traps. [B] 150MM x

100MM size 'P' or 'R' type.

95 Providing and fixing screw down quarter turn bib taps of following size -

Brass cromium plated screw down bib tap -15 mm dia. 15.00 184.98 No.

96 Providing & Fixing approved best quality I.S.S approved heavy PVC Half

turn valve 2.00 125.00 No.

- 15mm.dia. Valve.

97 Providing & Fixing approved best quality I.S.S approved heavy PVC Half

turn valve 3.00 175.00 No.

- 25mm.dia. Valve.

98 Providing & Fixing approved best quality I.S.S approved heavy PVC Half

turn valve 2.00 250.00 No.

- 32mm.dia. Valve.

99 Providing & Fixing approved best quality I.S.S approved heavy PVC Half

turn valve 2.00 300.00 No.

- 50mm.dia. Valve.

100 Providing B.B. Masonry inspection chamber (MANHOLE) of approved

size including light type C.I. Cover with frame, necessary excavation

bottom concreting of .C.C. (1:3:6) 150mm. thick/ 225mm. thick B.B.

Masonry in C.M.(1:6) 12mm thick cement plaster in C.M.(1:3) inside &

to all exposed faces up to 300mm. below ground level, curing etc.,

including disposal off surplus excavated earth up to radius of 300 mt. 6.00 4152.00 No.

including 3 coats of white or colour wash to all exposed finished

surface etc. complete as directed by E.I.C., with free supply of cement

by the Board (B.B.MASONRY UPTO 1000mm. DEPTH.)--300X300 mm

101 Providing B.B. Masonry inspection chamber (MANHOLE) of approved

size including light type C.I. Cover with frame, necessary excavation

bottom concreting of .C.C. (1:3:6) 150mm. thick/ 225mm. thick B.B.

Masonry in C.M.(1:6) 12mm thick cement plaster in C.M.(1:3) inside &

to all exposed faces up to 300mm. below ground level, curing etc.,

including disposal off surplus excavated earth up to radius of 300 mt. 7.00 5461.00 No.

including 3 coats of white or colour wash to all exposed finished

surface etc. complete as directed by E.I.C., with free supply of cement

by the Board (B.B.MASONRY UPTO 1000mm. DEPTH.)--600x450mm

102 Providing & Fixing light type C.I. Manhole covers with water tight C.I.

Frame & fixing the same in concrete etc., complete as directed by E.I.C.

600mm x 450mm size not less than 35 kg.

103 Providing & fixing to wall, ceilling, and floor in plumb by means of GI

clamps of 18 gauge sheet with 1 to 1.5 mtrs. Distance 6.00 Kg. /cm2

working pressure polythene pipes of approved brand incl. joining with

approved solution & all fittings like bend, tee. Y bend plug bend with

water tight jointsIf pipe laid in trenchesscope -75mm Dia.

104 Providing & fixing to wall, ceilling, and floor in plumb by means of GI

clamps of 18 gauge sheet with 1 to 1.5 mtrs. Distance 6.00 Kg. /cm2

working pressure polythene pipes of approved brand incl. joining with

approved solution & all fittings like bend, tee. Y bend plug bend with

water tight jointsIf pipe laid in trenchesscope - 90 mm Dia.

105 Providing & fixing to wall, ceilling, and floor in plumb by means of GI

clamps of 18 gauge sheet with 1 to 1.5 mtrs. Distance 6.00 Kg. /cm2

working pressure polythene pipes of approved brand incl. joining with

approved solution & all fittings like bend, tee. Y bend plug bend with

water tight jointsIf pipe laid in trenchesscope -110 mm Dia.

106 Providing & fixing to wall, ceilling, and floor in plumb by means of GI

clamps of 18 gauge sheet with 1 to 1.5 mtrs. Distance 6.00 Kg. /cm2

working pressure polythene pipes of approved brand incl. joining with

approved solution & all fittings like bend, tee. Y bend plug bend with

water tight jointsIf pipe laid in trenchesscope -160 mm Dia.

107 Providing & Fixing 600X450X6mm. thick size approved best quality of

looking glass mirror Modi or gold fish, mounted on 6mm thick ply with

edging with PVC angle paL as directed with fixture as required.

108 P/F brass towel rail complete with C.P. Brass brackets fixed with C.P.

Brass screws. 8.00 597.22 No.

- 600 X20 mm size.

109 Providing & Fixing Capsule door closer 8.00 350.00 No.

110 Providing 2500mm internal diameter & 3.0 Mt. Deep soak pit including

excavation in all types of soil & soft rock & B.B CC(1:4:8) bedding,

300mm thick below masonry and 450mm thick B.B Masonry in CM(1:6)

up to 600mm height, 350mm thick for further 600mm and 230mm

thick for remaining height honey combed, plastering in CM(1:3)

outside up to 1.5 Mt height and 100mm thick RCC slab with

600x600mm C.I.HEAVY duty cover with frame, with necessary

reinforcement as per design & C.I Vent pipe 1800mm long with B.B 1.00 75828.00 No.

masonry pillar 350x350x450 plastered all around filling with 40 to

50mm size brick bats up to 1.5 Mt depth, including 16mm dia M.S’U’

shape steps, refilling including disposal of the surplus excavated earth

up to the lead of 500mt. Radius including 3 coats of white or colour

wash to all exposed finished surface etc. complete as directed by E.I.C.-

For HARD STRATA

111 Providing and fixing in position callapsible steel shutters with vertical

channels 20 x 10 x 2 mm braced with flat iron diagonals 20 x 5 mm size

with top and bottom rails of T_rin 40x 40 x 6 mm with 38mm dia, steel

pulleys complete with bolts, nuts, locking arrangements, stoppers

handles including applying a priming coat of read lead paint.

112 Providing and fixing rolling shutters of approved make made of 80MM

wide M.S. laths inter-locked together thorough their entire length and

jointed together at the ends by end locks mounted on specially

designed pipe shaft with bracket plates, guide channels and

arrangements for inside and outside locking with push-pull operation

with gear system including the cost of hood cover and spring etc.

complete, of approved guage by EIC. [A] Shutters having width below

113 P & F steel cupboard shutter of 20 gauge with steel frame & fixing the

frame with brick masonary including locking arrangement with 1 coat

of primer ( red oxide ) i.e asian, dulux or its equivalent and 3 coats of

approved oil paint i.e asian, dulux or its equivalent etc. complete as per

requirement and instruction of EIC.

114 Providing & fixing of wall cupboard shutters using 18MM plywood

with Wood Framing size of 25 x 35 mm, decorative laminate of

approved shade & brand on front side and backside with white

laminated sheet. Including finishing with beading patti and polishing

the same. Fixing of door with hinges, one number of magnet and door 32.00 4467.00 Smt

handle on each door and one number of door lock and stopper for

locking arrangement good quality etc. Complete including materials

and labour as direction of Engineer in charge.

115 Fabrication of MS angle, channel, girder etc. as per design and

drawings including cutting, welding the section, necessary nut, bolts

and one coat of red primer and 2 coats of oil painting of approved 2250.00 39.00 Kg

shade with free supply of structutal steel only by the company.

116 Steel work welded in built up setions, framed work including cutting,

hoisting, fixing in position and applying a priming coat of red lead paint

and two coats of oil paint:- (A) In beams and joists, channels angles

Tees, flats, with connecting plates or angle cleats as in main and 960.00 97.58 kg

cross beams. Hip and jack rafters, purlins conneted to common rafters

117 Providing and fixing Stainless Steel railing having 75 mm dia, hollow

stailess steel pipe hand rail and 40 mm dia. Hollow stainless steel pipe

with combination of 10 cm long 20 mm dia pipe as vertical support

with 20 mm dia hollow pipes 3 rows as intermidiate members running

throughout with steel bol as cap at each end including cutting, bending,

welding & fabrication the structure as per drawing in 404 grade of steel

etc. completed as per instruction.

118 Providing corrugated G.I. sheet of class-3 roofing fixed with

glavanished iron J or L Hooks, Bolts and nuts 8mm diameter with

bitumen and G.I. limpet washer or G.I. limpet washer. filled with white 110.00 719.93 Smt

lead complete excluding the cost of purlins, Rafters and Trusses.(1)

0.80 mm thick sheet.

119 Providing and fixing building faced structural glasing with mukkion-

126mmx60mmx2.5mm Transom 86mmx60mmx2.5mm subframe

30mmx45mmx1.8mm duly anodised with 20+/-5 micron with M.S

bracket 75 mm x75mmx6mm thick spacer backer rod silicon Dew

corning DC 995 and all accessories to make system waterproof with

6mm thick Reeflective glass rates are inclusive of scaffoldin and all

consumables etc

120 P/F single layer waterproof gypsum board 8mm thick of the make

newgood group co.ltd or equivalent & newgood group co ltd company

section using waterproof board of size 1220mm x 1830mm x 8.0mm

suspended by GI suapender of size 25mm x 3mm with intermediate

channel of size 18mm x 40mm x 0.80mm at 1220mm C/C ceiling

section of size 40mm x 35mm x 0.55mm at 457 mm center to center

and perimetre chanel A of size 20mm x 27mm x 30mm x 0.50mm at

edges & drops including paper tap sand sofit cleat anchor fastener

scoch bolt connecting cleat joining compound top coat on ceiling

including making necessary opening for light fitting,diffuser

etc..compete as per detail drawing as directed.

121 Providing and fixing gypsum board decorative gilto of approved shape

and size as per requirement of site situation including required

structure. rate includes the fixing on wall or ceiling or at junction Of

wall and ceiling

122 Providing and fixing precast rubber dye inter locking concrete block

60mm thick with grade of concrete M-200 pnumatic comressed by

mechanically pressed and as per approved design including 75mm sand

layer for levelling and filling the joint with sand in proper line and level

etc comp as per directed.

123 Drilling of bore well of 175mm.dia. by machine in all kind of soil, sand,

clay, murrum, soft rock & hard rock etc., complete, truly vertical with

all equipments and labours etc., complete as directed by E.I.C. a) 0 to

124 As above but b) 151 to 180 M depth. 30.00 717.00 Rmt

125 Providing, fixing & lowering heavy duty 10 KG / CM2 P.V.C. casing pipe

suitable for 175 mm dia bore well including necessary coupling

connector, solution etc. complete as directed by E.I.C.

126 Providing and fixing best quality of HDPE pipe of approved ISS quality

with all accessories fittings jointing etc. suitable for submesible pump

lowering in bore etc. complete as directed by EIC. (B) 32mm dia. Outer

127 Providing and fixing of cable Laxson or equivalent brand 4 mm three

core copper ISI approved make incl. connecting with submersible

motor and with approved tap to HDPE pipe at 3.0 mt interval etc.

completed.- for Three Phase

128 Providing and fittings of standard swith board with Ampere and Volt

meter , fuse etc.suitable for single phase submersible pump with

metal/wooden covered box with locking arrangements and fiiting on

wall as directed.

129 Supplying and lowering 5 H.P. Three Phase. submersible pump of

approved brand with ISI mark including lowering vertically, fitting with

HDPE pipe and top clamp and connecting cable with motor and switch

board including all necessary accessary like Nipple, Bore Cape, Bussing, 1.00 41112.50 No.

Non Return Valve Etc. including and commissioning etc. completed.

130 Providing and fixing Stainless Steel text i.e. "પ ચીમ ગુજરાત િવજ

કં પની લીમીટે ડ" in 15" text, " પેટાિવભાગીય કચેરી, થાન-ઇ ડ ટીયલ અને

થાન- રલ." and "PGVCL" In 12" text in approved steel grade SS 304, 73.00 1058.00 Sft

including all fastners and fixtures at give location as directed by EIC

131 Providing and fixing pre-cast concrete Kerb stone of grey cement

based concrete block 30 cm length, 30cm height and 15cm thick of M-

200 grade concrete as per approved design and including excavation

for fixing in proper line and level, filling the joint with C.M. 1:3

( 1-Cement : 3-Sand ) etc complete as directed by EIC.

132 Providing & fixing G.I. Barbed wire fencing (12/14 Gauge) having

mass and uniformity of Zinc coating & specifications shall be as per IS

2140 – 1978 & IS 4826 – 1979 code with minimum 70 micron coating

having 6 horizontal rows & 2 diagonals, fixing with angle posts by 111.00 155.50 Rmt

means of G.I. U pins or with R.C.C. poles by 14 Gauge G.I. Wire as per

drawing etc., complete as directed by E.I.C.

133 Removing the existing fencing post P.S.C. or angle iron from concrete

without damaging the post & stacking etc. complete including dressing

the ground as directed by E.I.C.(material to be credited in Store)

134 Dismantling the barbed wire fencing pinned with R.C.C./P.S.C./Angle

or wooden posts from all rows & diagonals & bundling & stacking the

barbed wires as directed by E.I.C. etc. complete. (PAYMENT WILL BE

MADE IN RMT. OF COMPLETE FENCING WORK IRRESPECTIVE OF NO OF

ROWS.)(material to be credited in Store)

135 Constructing 125 mm thick Controlled cement concrete M- 200 Grade

with Trimix Vacumm dewatering system with power trowling sheet

form work with M.S. channels, srinking of fair hardness, Non oxidzing,

Non metalic, heavy duty floor hardner of FOSROC or equivalent at the

rate of 0.50 Kg./Sq.M. with 10 mm x 10 mm size groove cutting in 800.00 654.70 Smt

concrete as constructution joint and 12 mm thick premix expansion

joint at every 20 Meter lengthwith necessary equipments, labors as per

design etc. Complete.

136 Supplying & Spreading of quarry spall for filling of yard etc.,

complete.including spreading of quarry west in 150 mm thick layers

with required grade with watering rolling the each layer with 8 to

tones power roller etc., complete as directed by E.I.C.(Box

measurement will be paid with 15% deduction of voids).For Yard work.

137 Supplying & stacking murrum of approved quality including

Spreading,Watering consolidating By 8 to 10 tonnes power roller

transportation, filling the boxes etc. completed as directed. (Box 2100.00 611.50 Cmt

measurement will be paid with 15% deduction of voids).

138 Supplying & Spreading of stone dust for filling of yard etc.,

complete.including spreading of stone dust in 100 mm thick layers with

required grade with watering rolling the each layer with 8 to 10 tones 190.00 815.00 Cmt

power roller etc., complete as directed by E.I.C.

139 Clearing and grubbing road land including Dressing & Leveling

uprooting rank vegetation grass bushes,shrubs,sapling and trees girth

up to 300 mm removal of stumps of trees cut earlier and disposal of 4300.00 13.00 SMT

unserviceable materials(A) By manual means in area of light jungle

140 Providing & fixing sliding gate of 40mm. Dia Mild Steel Pipe 'B' class all

round and 20mm. Dia. Mild Steel Pipe at 200mm. C/C and 12mm. Mild

Steel Square bars at 200mm. C/C alternatively (i.e ONE BETWEEN TWO

PIPES) verically welded to 40mm. Dia. Pipe. frame as per drawing and

design with necessary brackets, hold fasts, locking arrangement on top

& aldrop on both sides including base rail for sliding the gate having

ball bearing rollers & guide track of 50X50X6 mm MS Angle with hold

fast, fabrication of side supports including fixing 'PGVCL' lettters on

front side etc., complete with three coats of approved oil painting &

one coat of red oxide primer as directed by E.I.C.

141 Demolition of Brick work and stone masonry including stacking of

serviceable materilas and disposal of unserviceable materials with all

lead and lift.(ii) In Cement Mortar.

142 Dismentaling doors, windows, ventilatros etc. (wood or steel) shutters

including chowkhtas architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift.(i) Not exceeding

143 Dismentling steel work including distempering and stacking the

materials with all lead and lift. 200.00 3.63 Kg

144 Demolition Including stacking of serviceble materials and disposal of

unserviceable materials with all lead and lift. (i) R.C.C work

145 Providing and fixing wooden Partition of sandwich type 36 mm thick

made up of @ 600 mm x 600 mm grid made up of 18 mm thick ply with

6 mm thick ply on either side laminated with 1.0 mm decorative

sunmica of approved design including bidding and polishing of same

inclusive all type of material and labour etc. complete as directed by EIC

146 Proving Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below type

of pipe erected with 6A Modular type switch / bell push & accessories

and earth continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat. III

147 Proving Point wiring for FAN with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of .ISI marked 1.1 KV Grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length, in below type

of pipe erected with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and accessories with earth

continuity of following type erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

148 Providing Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with 12.00 697.91 Pt.

following type of accessories.[II] For 16A Plug and 16 amp switch with

2-2.5 sq.mm Cu. Wire from mcb db board.(f) with medium class Rigid

PVC pipe and accessories erected concealed in wall/ceiling complete

149 Providing Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

PVC / Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected with 50.00 473.69 Pt.

following type of accessories. [I] For 6A Plug and 6 a switch with 2-1.5

sq.mm Cu. Wire from nearby switchboard/mcb db board (f) with

medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

150 Providing Point wiring for on board Looped Plug with 6A Modular type

switch & 5 pin socket erected on PVC / Metallic/Wooden box, single

mounting base frame covered with textured / metallic/white front 21.00 241.39 Pt.

plate modules erected on / in wall / ceiling with following type

accessories. Cat III

151 Providing following type of Modular Type Accessories mounted with

PVC / metallic/Wooden box, single mounting base frame covered with

textured / metallic/white front plate , modules erected with necessary

connections as per site situation directed by Engineer In charge. (8)

Computer RJ-45 socket Cat.III

152 Proving Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following type

of pipe to be erected concealed in /flushed on wall/ceiling, with 1.5 sq.

mm copper conductor FRLS PVC insulated stranded wire of green 830.00 78.78 Mtr.

colour for earth continuity of following size (A) With medium class

Rigid PVC pipe and accessories.(b) 2 wire 2.5 sq. mm

153 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears, 40.00 135.34 Mtr.

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required.(g) One wire 16.00 sq. mm

154 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears, 30.00 53.53 Mtr.

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required.(a) One wire 6.00 sq. mm

155 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears, 40.00 87.87 Mtr.

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required. (f) One wire 10.00 sq. mm

156 Providing and erecting Mains with ISI marked, 1.5KV grade electrolyte

multi stranded, annealed copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays, power switchgears, 10.00 286.84 Mtr.

motor starters & control wiring) with required size of copper lugs, nuts

and bolts if required. (i) One wire 35.00 sq. mm

157 Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered

with textured/metallic /white front plate,modules erected with

necessary connections as directed 36.00 1081.71 Each

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat. III

158 Providing & Fixing Decorative call bell Ting-tong box type 250 volts

complete erected

159 Proving Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%,CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency > 85 % (

fitting required LM-79 & LM-80 Certificates)(NOTE: Below description

have shown ranges of Wattage capacity of LED fittings.The Engineer

incharge may select any wattage capacity between the ranges shown.)

(A) Tube Light with integral driver (v) 36-40 Watts, Surge-2 KV, IP-20,

conventional 4 feet Cat-lll

160 Supplying and erecting led lamps with following wattage capacity of

220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-

surge protection,Polycarbonate diffuser, mounting suitable for E14 /

E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (iii) 10 to 15 watts Cat-III

161 Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with Fixed thermal & magnetic

release suitable to work on A.C. supply 50 c/s. with all internal 2.00 6173.12 Each

connections, spreader tinned copper & complete erected in existing

G.M.S. housing.ICS=100% of ICU only Cat III

162 Providing and erecting Approved make Four pole moulded case circuit

breaker having breaking capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal & magnetic release suitable

to work on A.C.supply 50 c/s. with all internal connections, spreader 2.00 16221.61 Each

tinned copper & complete erected in existing 16 G.M.S.housing

ICS=100% of ICU only Cat III

163 Proving Supplying and erecting triple pole & neutral 440V / 500V panel

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current

/ cross section area) duly wrapped with colour insulating tape for phase

sequence of following current carrying capacity, erected with necessary 2.00 1961.42 RMT

bus bar supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections.(A) Suitable for

164 Proving Supplying and erecting triple pole & neutral 440V / 500V panel

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated current

/ cross section area) duly wrapped with colour insulating tape for phase

sequence of following current carrying capacity, erected with necessary 2.00 3202.71 RMT

bus bar supports /insulators, main cable socket to each bar, erected in

existing cubical panel with necessary connections. (B) Suitable for

165 MCB SP by providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

166 Providing & erecting 240 V MCB double pole switch for lighting Load (B

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in

existing box having following capacity (B) 40 Amp. Cat.III

167 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load

(C Curve) having 10KA breaking capacity & confirms to IS :8828 in

existing box having following capacity (c)63 Amp. Cat.III

168 Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (B) three phase

incoming and single phase horizontal type outgoing Per phase

isolation type (PPI) (b) sheet steel double door (iv)12 way

169 Providing and erecting Approved make RCCBs conforming to IS:

and having sensitivity of 30 mA and Short Circuit withstand capacity of

10 KA and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do 18.00 2235.13 Each

not incorporate any electronic component. for following Max. rating

erected as directed (ii) 40Amps. DP Cat III

170 Providing and erecting HOT deep Galvanised iron strip wire 8 to

171 Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge

dissipation suitable for following type of applications with chamber and

heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the

value of earthing resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)- Resistivity:-

0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt

at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. (a) For Electrical

Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

172 Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board necessary IP-

42 and above protection as per approval from engineer incharge made

from 14 SWG thick CRC M.S. sheet for outer body & doors, 16 SWG

thick CRC M.S.sheet for internal partitions with necessary accesories

supporting angles/ flats channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable alley as per

requirements & instruction of engineer-in-charge with erection of

supplied switch gears, BUSBARS, suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber gasket,heavy duty end

terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with

epoxy powder coating. (The rates excludes the cost of switchgears, bus

bars, inter connecting mains & Copper Aluminium strips, meters, Fuses

etc. The dimension shall be measured excluding base beams) The panel

shall be supplied with following approved manufacturers with

following size.(A) locally fabricated panel board (i) with 350 mm depth

173 Proving Providing & erecting Approved make Power Saving 50 Watt

Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt

A.C. 50 Hz 1200 mm sweep complete having 3blades with aluminium

blades with , canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

174 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S.

Pipe down rod erected duly painted for fan complete with proper

insulation without leakage and earthing.

175 Providing & erecting water cooler having storage capacity 150 Ltr. &

cooling capacity 150 Ltr.per hour @ an ambient temp of 45˚ C. The

outlet temp. of the water should drop by 15˚C within a hour, The water

cooler should be comprising of hermetically sealed compressor, fan

motor, condensing unit, water tank surrounded by evaporating, coil,

thermostats, relay etc.complete with necessary inlet & outlet

connection. The body of water cooler will be made from Stainless Steel.

176 Supplying & Erecting LAN cable of Gray or White color of company

make D-link for following size in existing pipe fitting as per direction

[C] CAT - 6 type including CCTV camera LAN cable. (Note : LAN Cable 800.00 45.45 Mtr.

quantity can be vary depends on installation.)

177 Supplying & Erecting LAN cable of BLUE color of company make D-link

for following size in existing pipe fitting as per direction [C] CAT - 6 type

for network switch Uplink and CCTV camera Uplink

178 Supplying & erecting approved make Fiber optical cable of following

size in existing pipe fitting as per direction -10 pair capacity 40.00 45.45 Mtr.

179 Supplying & erecting approved make 5 nos of HDMI 4K cable for CCTV

camera+Conference room each 10 meter existing pipe fitting as per 24.00 3030.00 Mtr.

180 Providing and erecting ISI mark Medium class RIGID PVC PIPES of

following size complete to be erected on/in wall or ceiling erected

with necessary PVC fittings & Junction boxes fixed with adhesive 400.00 32.32 Mtr.

solution & Clamps with following dia of pipes, in approved manner as

directed (b) 25 mm

181 Supplying & erecting 5 stage single reverse osmosis water purification

system with M.S. powder coated frame, prefilter housing with 'O' ring

presediment filter GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post carbon filter auto

low & high pressure switches with following size of storage tank & LPH

capacity & erected as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster

182 Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High

pressure die cast aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and Polycarbonate

optics/ lenses, with toughened glass with company mark/name

engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD

< 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings 5.00 6566.01 Each

required LM-79 & LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (iv) above 90 to

183 Supplying & erecting approved make SMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with

cable clamps& earth bolt of following size of box.(D) 140mm x 140mm

184 Supplying and erecting B class Galvanized iron pipe having smooth

finished bore of the pipe on both ends erected nuts and bolts along

the pole / wall shaping the pipe as per site requirement. Pipe dia as

following.(B) 32 mm dia

185 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

Aluminium conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of cables.(A) 2 core

186 Supplying and erecting Flexible PVC insulated multi strand multi core

1.1 kv grade ISI marked copper wires of following size to be erected as

directed.(h) 2.50 Sq.mm 3 core round PVC sheathed

Bidder's offer [B]

GRAND TOTAL [C = A +/- AxB ]

GRAND TOTAL [C = A +/- AxB ]

GST (CGST __% + SGST __%) [ D = C x GST% ]

GRAND TOTAL INCLUDING GST [ E = C + D ]

GRAND TOTAL INCLUDING GST [ E = C + D ]

Final offer in Rs.

Chief Engineer (Material)

PGVCL, Corporate Office, Rajkot