Development of Harbour beach in Thoothukudi City Municipal Corporation

Amount

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and M-Sand, silt or other loose soil, wet Sand,or silt not under water, light black cotton soil, Sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water and cleaning and levelling the site etc.,complete

Footings - First Depth

Second Depth

Plinth Beam

Supplying and filling in foundation and basement with filling Crushed Stone Dust in layers of not more than 15cm.thick well rammed watered and compacted etc., complete complying with standard specification.

Supplying and filling in foundation and basement with Well Gravel in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed

For column footing plinth beam bed blocks templates staircase, steps piers, raft beam, raft slab etc.

c) For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCCSlab, etc.

For Plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone Sand (M- Sand) and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors.

Providing and laying in position Standardised Concrete Mix M-25 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 3500 Kg/ 10cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of M-M-Sand, but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - The Coarse and Fine aggregates to be used should comply with the requiremnents of IS staandards. (No separate payment will be made by the Department for the excess usage of materials)

Up to Basement

Ground Floor

Brick work in CM 1:5 (one cement & five M-Sand) using Country bricks of size 9"x43/8"x23/4"including finishing, curing, etc., complete complying with standard specification

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Plastering with cement mortar 1:3,10 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications

Plastering with cement mortar (1:4) 20mm thick in all floors including cost and conveyance of all materials to site and labour charges etc, complete complying with standard specifications

Finishing the top of floor with Granolithic Finish with CC 1: 2: 4 (one cement, two M-Sand & four HBG jelly) using chips of grade 10 mm and below for 25mm thickness and rubbed smooth etc, complete as per standard specification

Weathering Course with Concrete Broken Brick (S.I.No.278) & ( P & D) Data 54.Jelly 20mm gauge in pure slaked lime (no M-Sand to be added) over roof slab,the proportion of brick jelly to lime being '32 to 12.5 well beated with wooden beaters for giving required slope and thickness as directed by the departmental officers etc., complete

Finishing the top of roof with one course of machine pressed tiles of size 200 mm x 200 mm x 20 mm of approved quality in Cement Mortar 1:3 (One Cement add three M-Sand) 12 mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete

Paving the floor with Vitrified Marbonite tiles of Double Charged approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three M-Sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Paving the floor with Vitrified Marbonite tiles of stain free nano polish approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three M-Sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Dadooing walls with Glazed tiles of sizes 305mm X200mm X 6mm size of approved make and quality and colour l Set in cement mortar 1:2 (one cement ,two M-Sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 83mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with stone dust cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, stone dust cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,.

Paving the floor with granite slab of Jet Black approved quality and colour of size 1200x600xthick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three M-Sand)18mm to20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Painting Two Coat with Ready Mixed Enamel Paint over the new wood works of approved quality and colour with priming coat including the cost all materials etc.,complete, in all floors.

Painting Two Coat with Ready Mixed Enamel Paint over the new Iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Painting two coats with ready mixed Interior Plastic Emulsion Paint approved quality and colour with Primer for Plastic Emulsion Paint, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Painting two coats with ready mixed Exterior Emulsion Paint approved quality and colour With priming coat for Exterior Emulsion Paint - Water Based Primer (Liquid )including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification.

Providing country wood Wrought and put up frame for door and window any other similar joinery works using following size of upto 4m in length Country wood scantling of pillai maruthu or patak including labour for wrought and putup in position etc., complete complying with standard specification..

Supplying & fixing door shutters for Mediun Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive of threee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. Thewindow should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work *(PWD SOR 23-24 M- 0674 pg.no: 70)

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Newly Constructed Roof/Bathroom/Toilet/ balcony/utility with Cementatius Waterproof coating below 500 Sq.m Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid:7 Powder) to the RCC surface like Roof, bathroom, toilet, balcony & utility area applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break >120% as per ASTM D 412, Tensile strength >1N/ mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The fnished cost includes surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45gsm glass fbre mesh over the angle fllet when the first coat in still wet, treatment of cracks completely as per specification.

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Mild Steel Red Cargo Container Open Shop, Capacity: 10-20 ton Container Type - Open Top Container Container Length - 20 feet Capacity - 10-20 ton Color - red Material - Mild Steel

1. Model no: NL-07,40ft length, 10 ft. width and 10 ft. Height double layer 6 inch round pipe. 2.6mm thickness with bending with FRB coated painting 10 numbers double swinging seated every seat different model as per requirement. 3. 6 inch pipe connecting point 12 inches round 10mm plate 4. Total no.of join to join plate 16 numbers 5. Laser cut 12 inch round plate 6 no.of holes 6. The connecting bolt and nut 24 mm heavy 120 numbers 7. Basement plate 24 mm 1.5 x 1.5 sqr Ms Plate with laser cut 12 Number 24mm bed bolt 6 numbers 8. Swinging seated mounting area d clamp 24 mm 6 inches laser cut with holes 20 numbers 9. Swinging seat 10 no.of customized design

ARCH MODEL 1. Model no: NL-13, Arch model, 30ft length, 10 ft. width and 8 ft. Height single layer 6 inch Square pipe. 2.6mm thickness with bending with FRB coated painting 3 numbers round swinging Seated 3. 6 inch pipe connecting point 12 inch square 10mm plate 4 numbers 4. Laser cut 12 inch round plate 6 no.of holes 5. The connecting bolt and nut 24 mm heavy 20 numbers 6. Basement plate 24 mm 1.5 x 1.5 sqr Ms Plate with laser cut 12 number 24mm bed bolt 4 numbers 7. Swinging seated mounting area d clamp 24 mm 6 inches laser cut with holes 6 numbers 8. Swinging round seat 3 no.of customized design

SWINGING FAMILY SEATED 1. Model no: NL-06, swinging family seated 15ft length, and 8 ft. Height single layer 6 inch Square pipe. 2.6mm thickness with bending with FRB coated painting 3 numbers single 6 ft. family Seated 3. 6 inch pipe connecting point 12 inch square 10mm plate 2numbers 4. Laser cut 12 inch round plate 6 no.of holes 5. The connecting bolt and nut 24 mm heavy 10 numbers 6. Basement plate 24 mm 1.5 x 1.5 sqr Ms Plate with laser cut 12 number 24mm bed bolt 2 numbers 7. Swinging seated mounting area d clamp 24 mm 6 inches laser cut with holes 4numbers 8. The elevation family seated the conch FRB fiber molding. The conch model for nature design.

CHILDREN’S SLIDERS SHIP MODEL 1.40 ft length, 6 ft width six different type sliders for ship model 2. The ship model entire fabricate 3 inch Ms square pipe with FRB covering the ship model and slider 3. The slider 10 to 15 ft. length and 8 ft. height types or spring type, straight type, left and right, up and down and group, models.

CHILDREN’S SLIDERS BOAT MODEL 1.15 ft length, 4 ft width two different type sliders for boat model 2. The boat model entire fabricate 3 inch Ms square pipe with FRB covering the boat model and slider 3. The slider 8 ft. length and 6 ft. height types or straight type.T

ILLUSION HALO FACE View height 10 ft width 6 ft unique modern work customized material basement 6 ft debt 4 x 4 box colum 8 ft square mat concrete with cement coated with natural color painting full natural coated painting

ILLUSION FACE View height 8 ft width 8 ft unique modern work customized material basement 6 ft debt 4 x 4 box colum 8 ft square mat concrete with cement coated with natural color painting full natural coated painting

ILLUSION COUPLE FACE View height 6ft width 4 ft unique modern work customized material ILLUSION CYCLING View length 5ft height 3 ft unique modern work customized material metal and concrete basement 6 ft debt 4 x 4 box colum 8 ft square mat concrete with cement coated with natural color painting full natural coated painting

SCULPTURE ZONE-1 Sculpture Size: 8 ft height, 15ft widht, 8 ft debth sculpture used for 8 ft height, 15 ft widht iron rod the foundation 12 mm rod supporting rod 8mm 6mm full covered mess covering widht cement coating full natural coated painting basement 6 ft debt 4 x 4 box colum 15 ft dia round mat concrete with cement coated with natural color painting with Led solar lighting 6 no'

BIRDS ZONE 3 Birds 1: Height 8 ft, 3 ft debt Birds 2: Height 5 ft, 2 ft debt Birds 3: Height 3 ft, 1.5 ft debt full covered mess covering widht cement coating full natural coated painting basement 6 ft debt 4 x 4 box colum 15 ft dia round mat concrete with cement coated with natural color painting basement to pillar 5ft height pillar with Led solar lighting 10 no's

Ring two layer round nozzile fountain . size : 6 ft round dia 8 ft height The lightweight, yet heavy duty spray systems are made of superior quality 304 stainless steel and incorporate brass, nickel plated adjustable nozzles, with an option of the entire system to be made of 316 stainless steel. All water inlets of the Spray Rings are male threaded and every one of them is fitted with a flow diverter to achieve optimum performance. All jets (>5mm) have integral flow straighteners for excellent water flow and greater efficiency. Larger models are dispatched split in 2-6 pieces (with flange connections) for safer and easier transportation. In addition, all Spray Rings are shipped equipped with placeholders for detachable, adjustable telescopic legs and luminaire mounting brackets making installation quicker than ever before. FOAM FOUNTAIN LED LIGHT All Lights are customized with options of colors. 3w x 36w SMD LED is assembled in custom made aluminum made PCB’s and assembled. These lights water proof are confirming IP 68 rating with 12v 10 amps high power AC to DC convertor SMPS Power Supply with Water proofing IP66 PVC box SMPS FOR LIGHTING Output Voltage 15V Type Enclosed Type Approx. Wattage 348WFeature Standard Series LRS(Reliable) Mechanical Form Enclosed Warranty 3 Years Warranty IP Level Non-waterproof Input Voltage 115V/230V by switch No load power consumption

FOUNTAIN FABRICATION Aluminium Leg 1.1/2” Square Polished Pipe = 3 leg 1x1ft 4mm Square Plat = 1 No’s 1”Square supporting leg = 3 leg Complete fabrication welding and labor charges including UPVC PLUMBING MATERIAL ITEMS All the Pipe shall be of branded manufacturers with ISO standards (Example:- Finolex Or Supreme ). Underwater grade 3 mm 1”UPVC Pipe all use for all motor and Nozzle Connecting Line connectors are given for every Pipe joints for protecting the joints from exposing with water. CONTROLLER UNIT WIRING ITEMS All the cables shall be of branded manufacturers with ISO standards (Example:- Finolex). Underwater grade 2.5 sq.mm 4 core motor flat cable 1.5sq.mm 4 core round cables shall use for all motor starter and MCB and switches. Waterproof junction boxes connectors are given for every cable joints for protecting the joints from exposing with water. Fountain Round S S Pipe Ring Fountain Round Pipe Material Stainless Steel 304 Size 1.5” 48mm 1.8 thickness Color Slivery Direction Adjustable Operating temperature: 0-100 degree Fountain water height 5 – 10 ft Water effect Ring fountain Installation External thread Fountain Nozzles Water Jet Fountain Nozzle Material Brass Niggle Coating Stainless Steel Size ¼” Color Slivery Direction Adjustable Non-Adjustable Fountain water :5-10 ft Water effect High flow fountain Installation External thread FRB fiber antiq look fountain covering 8 x 8 round water proofing tank with instalation

Element on the rope course number of activities 1. Adventure rope rider, 2. Artificial Rock climbing Children’s, 3. Children's zip line, 4. Jumping on The rope, 5. Swing on the rope children’s, 6. Rope climbing children’s, 7. Net Caroling, 8. Monkey Crawl 9. Catwalk, 10. Burma Bridge, 11. Slack line, 12. Dobell Rope Bridge, 13. Zig Zag, 14. Log to Log, 15. Space Walk, 16. Horizontal Ladder, 17. Tyre Crossing, 18. Tyre Bridge, 19. Commando Net, 20. Commando Crawling, 21. Rope Ladder, 22. Swing Bridge, 23. Net Bridge, 24. Adult Zipline. ADVENTURE PARK SETUP PRODUCTS 1. All outdoor adventure activity in one roof firstly we install Ms Structure size 150 ft x 50ft the square type 3 level the25 ft height in activity area. 2. The structure model left side150 ft right side 150 ft and front side 50 ft and back side 50 ft. 3. Every 30ft install pillar 4. Double model and 3 level cross bar 5. The one side staircase and starting and landing tower 30 ft height 6. Every pillar used to 10 inch the round pipe 6mm 7. Double model and 3 levels cross bar 4 inch 3 mm Ms Pipe. 8. Staircase diamond 3mm sheet with hand rides. 9. Setup with "Top Bellay System" and certified wire/ropes with locks. 10. Set of safety gear. (Harness/Helmet/Anchor rope/attachmentsetc.) 11. Railing – Fencing iron net. 12. Cable rope 10mm/GI/6:19/steel core/Galvanized. 13. Supporting & safety cable - 10mm 14. Wood - thick 35mm./seasoned/local best. 15. Clamps & nut bolts – SS/GI/tested/self-locked. 16. FRB coated rust proof Paint 17. Tree protected eco-friendly cable locking system. 18. Turn buckle – Jaw to Jaw open type/16mm/certified. 19. Bow shackle – Bolt system pin lock/2&3tn/certified. 20. Bull wire grip clamp – 10mm/GI /Heavy duty/certified Bolts & Nut Material: Quenched and tempered steel. Temperature range: -40°C to +100°C - Use at higher temperatures possible withreduction of WLL. Finish: Requirements for applied zinc flake coatings are covered in ISO 10683 Bolt standard - ISO 8992 Bow shackle Standard bow shackle with safety bolt acc. to NS 9415/ Hot dip galvanization Assures long-term durability / double safety (cotter pin & safety bolt)/ EN 13889

Bull dog grip Wire Rope Clip - Drop forged steel Galv. type for 1/8 in. diameter wire rope. Wrench Size: 3/8 inch. Note: U-Bolt and Nuts are Zinc Plated. Wire rope 4 line connection Cable rope which will be connected with plumber block on top &with swing bar in down. Cable locked with ferrule punch & edge socket system. Winch cable will non rotating cable12mm/GI/steel core/IS 2266 Mini platform details: 1. Dimension – 1.2/1.2mtrs. 2. Mini platform frame will be with 60/60/4mm angel. 3. Locking system for platform with 150/6mm C-clamp. 4. Wooden planks – 1.5”/8”/36” teak or local best/seasoned. 5. C-Clamp locked with 16mm HT bolt, Easy dismantlessystem. 6. Every platform will be connected with emergency exitladder. 18”/120”. Base platform details: 1. Width – 2mtrs. Length – 2mtr. 2. Iron frame – main support - 75mm angel/cross support – 60mm angel. 3. Tree locking system for platform with 100/6mm C-clamp. 4. Ms diamond plate – 1.5”/6”/72” teak/mahogini or local best/seasoned. 5. C-Clamp locked with 16mm HT bolt, Easy

Supply and fixing in position white European Water Closet of approved make with low level flushing tank 10 litre capacity of best quality and approved make with 100mm P or S trap with double flapped rigid PVC seat cover with CP brass hinges etc. complete complying with standard specification and as directed by the Departmental officers (The EWC should be got approved by the Executive Engineer before use on works.

Supplying and fixing Lipped Mouth Porcelain White Glazed Porcelain Oval Shape Special Type Urinal of size 382 x 398 x 601mm with all accessories such as 32mm dia Bell Mouth PVC Connection, 15mm dia GM Wheel Value, 15mm dia 'B' Class GI Waste Water Pipe, 15mm dia Nylon Connection, 15mm dia Brass Nipple, and suitable screws, shellac etc., complete. The rate including cost of all materials, labour charges for fixing and transportation etc. completed as directed by Engineer-in-Charge.

Supplying and fixing Wash Hand Basin of size 550 x 400mm with all accessories such as cast Iron Brackets, 32 mm Dia C.P. Waste coupling, Rubber plug and Chain, 32 mm dia ' B ' Class G.I. Waste pipe, 15 mm Dia G.M Wheel valve; 15 mm Dia Nylon connection, 15 mm Dia Brass Nipples, 15 mm C.P. Pillar tap etc.,including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and as directed by the Department officers. (The Wash basin should be got approved by the Executive Engineer before use on works.

Supplying and fixing of CP Two Way Bib Cock with Health Faucet ,wall hook & one metre long flexible tube including cutting and making good the walls wherever required etc complete. complying with standard specification and as directed by the Department officers. The quality and make of health faucet should be got approved by Concern department Engineer before use on work.

Supplying and fixing the best quality approved make of SS heavy duty long body Tap including cutting and making good walls wherever required etc.complete,complying with standerd specification and as directed by the department officers. The quality and make of angular stop cock should be got approved by concern department engineer before use on work.

Supplying & fixing in position 15 mm dia brass/ C.P screw down tape (Heavy duty) of approved make conforming to I.S. Specifications & quality including cost of shellac, thread etc., complying with standard specifications & including cutting & threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the work).

Supplying and fixing in position Mirror of size 600x450mm of approved quality and brand with necessary plastic back PVC frame with bottom stand using brass screws rawl plugs for fixing etc complete complying with standard specification and as directed by the Departmental officers. The colour of frame and quality of mirror should be got approved by the Executive Engineer before use on work

Supplying,installing,testing and commissioning of approved make CONCELD STOP COCK for toilet including neccesary accessories etc,complete,works include making require size curout in wall,and fixing the control box property,redoing the same etc,complete the quality and make of concealed stop cock should be got approved by concern department Engineer before use on work.

Supplying & fixing in position PVC Nahini / Floor trap of size 100x75mm including stainless steel gratings of approved brand & quality, fixed over a bed of brick jelly lime concrete 1:2:5 ( One part of lime, two parts of sand & five parts of 40 mm size brick jelly ) & finished with cement mortar 1:3 ( One cement & three sand ) including dismantling masonry works wherever found necessary & making good the damaged portions to the original condition & giving connections to the cast iron pipes etc., complete, complying with standard specification. (The PVC Nahini / Floor trap should be got approved by the Executive Engineer before use on works ).

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). INTERNAL SOIL AND WASTE PIPE SYSTEM:

a) 40 mm dia

b) 75 mm dia

c) 110 mm dia

EXTERNAL SOIL AND WASTE PIPE SYSTEM:

a) 75 mm dia

b) 110 mm dia

c) 160 mm dia

Constructing solid block masonry manhole various size of deep in cement mortar 1:3( 1 Cement: 4 coarse sand ) R.C.C. Raft & top slab with cement concrete 1:2:4, plain cement concrete 1:4:8 mix for base course (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size )above that 150 mm thick RCC M25 raft slab inculding reinforcement 10mm dia 150mm c/c bothways. Plastering inside walls with 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand ) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ), finished with a floating coat of neat cement ,supplying and fixing SFRC manhole cover with farame of size 600x600 mm , PVC foot rest as per detailed drawing etc the quoted rate shall also necessary excavation and back filling etc complete.complete as per standard design : (the chamber and cover should be got approved by the Executive Engineer before use on works)

Supplying, laying and jointing CPVC pipes SDR 11(having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Internal & Vertical

a) 15 mm dia

b) 20 mm dia

c) 25 mm dia

EXTERNAL WATER DISTRUBUTION:(TERRACE,SHAFT, EXTERNAL PIPE) Supplying, laying, jointing, testing & Commissioning of UPVC Schedule 80 pressure pipes as per ASTM D 1785 with Sch 80 Fittings as per specifications, jointing with hold tite / super tite & tefflon tape and complete with fittings such as sockets, unions, reducers long or short bends, elbows, nipples flanges,checknuts,etc. Pressure testing of piping and back filling of trench complete as required. The quoted rate shall include necessary earth works, fittings like Tees, Bends, Offsets etc., G.I. brackets with pvc coated GI clamps, nuts & bolts, anchor fasteners, grip bolts, GI threaded, rods, etc., complete for external pipes. (For under ground or above ground external water supply piping.) Vertical & External

a) 25 mm dia

b) 32 mm dia

c) 40 mm dia

e) 50 mm dia

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

a) 20 mm dia

a) 25 mm dia

b) 32 mm dia

c) 40 mm dia

c) 50 mm dia

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALEN

Supply and Fixing PVC Water Tank

Supply ,erection and testing & commisioning of 5HP Submersible pumpset in the capacity of 6000 LPH @ 300Ft, max. total head of 350 Ft pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge.( Sump to OHT transfer pump)

Supply ,erection and testing & commisioning of 2HP Monoblock pumpset in the capacity of max 3 bar Pressure pumps fitted with bronze impellers and having delivery size of 40mm - 430V along with 3mts cable and manufactures standard control panel which is mandatory and as directed by the officer incharge.( Terrace Booster Pump)

TNEB METERING BOARD Supply,installation and commissioning of TNEB Meter Board suitable for 3 Phases 200 A service connection made up of suitable iron angel frame work of size 2 feet x 1.5 feet using angle iron of size 1 1/2" x 1 1/2 " x 1/4" rigidly fixed on wall covered with Hylem sheet of size 2 feet x 1.5 feet of 12 mm thickness with necessary bolts and nutts supports and Supply,installation and commissioning of 3 nos 200 A fuse units (500V) ,1 No Neutral link ,Copper flat of size 1" x 1/4" with interconnection of EB meter to fuse units by 19/16 PVC insulated copper wire with earth connection and to complete the work etc.

Fabrication, Supply, Erection, Testing and Commissioning of whether proof CRCA sheet steel powder coated MCCB Indoor Panel Board, made up of 2mm powder coated, including bus bar provision of double door with industrial lock with Multifunction Meter 1no and 1no Change Over Switch, Main 2nos 200A 4Pole MCCB I/C, 3Nos of 100A 4Pole MCCB,6nos of 63A 4Pole MCCB's, and 3nos of 32A 4Pole MCCB's for O/G with suitable copper bus bar (33x6mm) having three phase Multifunction meter with line indicators for erecting the indoor panel board complete etc., The above panel board is to be erected on Anchor fastners, bolts and nuts for mounting the Indoor Panel etc. complete.

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos. 32A 3P MCB, 15 nos. 6A to 32A SP MCB as outgoing on wall with earth connection only. Higher End -

Supply and fixing of 7 segment 4 way 63A TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 6 ways in each segment) and seperate provision for MCB / Isolators ( totally 18 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End-

Wiring, testing and commissioning of 2Rx1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe with 2 mm thick, ISI marked concealed in wall and ceiling with PVC accessories with Module GI Switch Box in flush with wall with 6A one way module switch with module front plate continuous earth wire connection by 2.5sq.mm PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light / Fan Point (for electronic) (6Points / Coil ) (length of point 12 to 18 mtr)

Supply and run of 2 of 2.5 sqmm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection 1 of 1.5sqmm (36/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade and making good of the concealed portion with suitable colour.

Supply and run of 50mm Dia HDPE pipe of 4kgf/cm2 approved quality and best variety conforming to ISS and ISI mark below ground in HDPE pipes.

Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V Grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 1 of 2.5 sqmm (36 /0.3) PVC insulated SC unsheathed Cu.Conductor with painting of suitable colour.

Supply and laying of 2C X 6 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and Laying of 4C x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and Laying of 4C x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good

Supply and laying of 3.5C X 25 sq.mm Al XLPE armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and laying of 3.5 x 70 sq.mm Al XLPE armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good.

Supply and fixing of brass cable gland for 2C x 6 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc

Supply and fixing of brass cable gland suitable for 4C x 10 PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland suitable for 4C x 16 PVC armoured LTUG cable with earth connection.

Supply and fixing of brass cable gland for 31/2C x 25 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc

Supply and fixing of brass cable gland for 3.5 x 70 sq.mm PVC LTUG armoured cable with earth connection with necessary accessories etc

Supply and providing cable end termination of 4 C x 10sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 4 C x 16sq.mm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping with electrical connection complete.

Supply and providing cable end termination of 3.5 x 25sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with eelctrical connection complete and etc to complete the work.

Supply and providing cable end termination of 3.5 x 70 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with eelctrical connection complete and etc to complete the work.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work

Supply and run of 25mm x 6.25mm Aluminium flat with necessary clamps / supports on wall / floor / ground for earth connection and etc to complete the work.

Supply and run of 2 of No.8 SWG GI wire for guarding with cradle with No.8SWG GI wire at the equal interval of 1.5 meter and etc to complete the work

Coil Earth to Street light poles with No 8 SWG GI wire of 11.5 Mtrs of length in which 10 mtrs of total length compressed in to a coil of one meter length (75 mm to 100 mm dia) connected suitable with Hexagonel earth bolt of size 8mm to 25 mm welded on the pole at one end with a coil position fixed on the earth and etc to complete the work

Supply and fixing of48W LED Compound wall Light with Suitable Pole.

Supply anf Fixing Highmast (16 Metre) with 8 Nos. 150W LED Fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of down light 18W Light fitting on ceiling with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of bollard light 11W fitting on floor with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and fixing of 120W Street Light Single arm fitting on 4mtr pole with metal support with PVC unsheathed copper leads from terminals to the fitting and to complete necessary accessories and etc to complete the work.

Supply and Fixing of 20W 4feet LED Tube Fitting with TW round blocks on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting and etc to complete the work

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1 meter rod with fan clamp with side plates and cross arm of size 450mm(18")

Supply and Fixing of 250 mm( l0") sweep (light duty) AC Exhaust fan and etc to complete with necessary wall opening and making good of the wall

Supply and fixing of 1no of 6A two Modular 5Pin socket, 1no 6A Modular switch with module cover plate (plastic) on suitable concealed in box (GI) in flush with wall with connection. Higher End

Supply and fixing of 1no of 16A two Modular socket, 1no 16A Modular switch with module cover plate (plastic) on suitable concealed in box (GI) in flush with wall with connection. Higher End

Supply, erection, testing, commissioning of 100KVA DG Set with Acoustic Enclosure with Diesel Engine developing suitable HP at 1500 RPM, 4 Cycle, 12 cylinder, water cooled, turbo charged, complete with standard Accessories confirming to latest emission control latest norms coupled to alternator rated at 100 KVA, 3 phase, 4 wire, 0.8PF (lag), 415V, IP 21 enclosure, class F/H insulation, with AVR, mounted on a channel iron base frame with foot mounting AVM pads, confirming to IS 4722, 1day capacity Litters fuel tank, 2x12V 120 AH battery with leads, AMF panel, Hospital type Silencer, with acoustic enclosure, control panel, inter connecting control cable, cable end termination, including necessary fuel tank system, lubrication system, cooling system, fabrication of exhaust M.S pipe system, supporting frame, structures arrangement, confirming to CPCB norms etc., all inclusive.

Supply, Installation, Testing and commissioning of 32 channel 2 SATA NVR, with 6T Hard Disk Drive 4 nos, New logical and visualized GUI design Dual-OS design to ensure high reliability of system running, ANR technology to enhance the storage reliability when the network is disconnected, Configurable normal or hot spare working mode to constitute an N+1 hot spare system Video Input and Transmission, Connectable to the third-party network cameras Compression and Recording, H.265+ compression effectively reduces the storage space by upto 75%, Full channel recording at up to 12MP resolution HD Video Output  HDMI1 / VGA1 outputs provided  HDMI1 Video output at up to 4K ( 3840 × 2160 ) resolution Storage and Playback, Upto 16 SATA interfaces and 1 eSATA interface for HDD connection, Support upto 10TB capacity for each HDD, Smart search for efficient playback.

Supply of 5MP, Internet Protocol fixed BULLET CAMERA with following specification:●1/2.5" Progressive Scan CMOS, ● 3840 × 2160 @15 fps,2.8/4 mm fixed lens,01 lux @ (F1.2, AGC ON), 0.028 lux @(F2.0, AGC ON), 0 lux with IR, H.265+, H.265, H.264+, H.264, 2 Behavior analyses ( Line crossing detection, intrusion detection)● Face Detection ● 120dB WDR, ● BLC/3D DNR/ROI, IP67 complied●On-board Storage - Built-in micro SD/SDHC/SDXC card slot, up to 128 GB,● Shutter Speed 1/3 s to 1/100,000 s, ● 3-Axis Adjustment Pan: 0° to 360°, tilt: 0° to 100°, ● rotate: 0° to 360°, 2.8 mm, ● horizontal FOV: 102°, vertical FOV: 53°, diagonal FOV: 124°, ●Lens Mount M12 ● IR Range I5: up to 50 m, ● Image Settings Rotate mode, saturation, brightness, contrast, sharpness adjustable by client software or web browser, ● Power Consumption and Current-12 VDC, 0.7 A, max. 7.5W PoE: (802.3af, 36V to 57V), 0.3 A to 0.2 A, max. 9W● Camera out fitted with metal housing so as to prevent the lens from damages during physical abuse.

Supply, Installation, Testing and Commissioning of 55" smart LED TV with following specifications a) Full HD 1920 x1080 (4K monitor) b) IPS pannel c) Slim back light LED module d) 900 PMI e) Triple XD engine f) Dynamic scanning g) ANR h) True colour generator i) 8modes of picture j) picture wizardIII k) Real cinema 24P l) HDMI -3nos m) USB -3nos n) Built in LAN o) Magic remote p) Dimension 1242 x 724 x 55.1min(37). (Make: Sony/ LG /Samsung).

Supply and Clamping of CAT 6 armoured cable in 25 mm PVC pipe below the ground complete with all necessary accessories etc.. (Between ethernet switch to camera and radio modem) i. Application : Primary (Campus), Secondary (Riser),Tertiary (Horizontal)IEEE 802.3 : 10Base-T; 100Base-T; 1000Base-TIEEE 802.5 16 MB; ISDN; TPDDI; ATM ii. Standards: ISO/IEC 11801 2nd ed.; IEC 61156-5 2nd EN 50173-1; EN 50288-6-1,EIA/TIA 568C.2, RoHS Compliant. Fire Rating: PVC : IEC 60332-1. iii. Conductor - Bare Copper Wire iv. Insulation - Polyethylene v. Twisting - 2 Cores to the pair vi. Cable lay up - 4 Core to the pair It has diameter of (23 AWG) 0.550 ± 0.015.Insulation : Polyethylene.GI wire of size is 0.90 ± 0.030mm.

Fixing and Termination of CAT 6 Cable RJ 45Jack Single Point ( Point to Point ) Crimping, Testing and arrangement charges.

Supply and fixing of POE 24 port switch 10/ 100 / 1000 Base -T / 2 x 1000Base-FX / 20Gbps bandwidth / IEEE803.af/at compliant PoE+ / RJ45 supports auto MDI/MDI-X function / Auto negotiation speed, half/full-duplex / Store and forward / Max packet size: 10kbytes / Wide range power design (12~56VDC) / Operating temperature (-40 ̊C ~ +75 ̊C) / Reverse polarity protection / Resettable fuse to protect against overcurrent / IP-40 protection / EFT protection for power line.

Supply and Fixing of Rack with Accessories -Higher end 36 U Rack with LNS unit and fan extra for the above rack.

Supply and Instalatin for 2nos of 1KVA UPS with Battery, Single Phase UPS (Single Phase In & Single Phase Out) Capacity - System with Battery - 2 Hours back up

Supply,Erection of 6m Length pole with base plate of size 300x300x12mm as per IS-875 with following specification. Pole Outter dia -76.10mm x 3.65mm Thick x 6 meter with foundation Charges

Clearing Heavy Jungle, Clearing Including Cost of Material and Labour Charges Such as Standard Specification