Renovation of Prarthana Hall near Lokniketan At Bhabhar Nagarpalika in Bhabhar Dist :- Vav Tharad

NAME OF WORK: -

Renovation of Prarthana Hall near Lokniketan At Bhabhar Nagarpalika

Qty. Item Rate Units Amount

Providing 15mm thick cement plaster in single coat on Rough

(Similar)side of single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii) Cement mortar

1:4 (1-cement :4-sand)

Wall painting (two coats) with plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even

2 539.00 shade including throughly brushing the surface free from mortar 83.18 Sq.Mt

droppings and other foreign matter and sand papered smooth.

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on

new surface or fixing on existing flooring by adhesive material

including dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing & cleaning the

surface etc. complete for DARK shade and light shade

Providing and fixing M.S. door and window prepared with ms equal

angle for frame and shuter with 18 BSG. Sheet Including Fixture and

fastening Including Red lead paint with two coat oil paint etc.

Including fixing in position .(As per R.A.)

Providing and fixing M.S. window with Ms Grill prepared with ms

equal angle for frame and shuter with 18 BSG. Sheet Including

Fixture and fastening Including Red lead paont with two coat oil

paint etc. Including fixing in position .(As per R.A.)

Providing and laying water proofing treatment with china

mosaic tiles flooring over avg 50 mm C.C. 1:2:4 bedding for

maintaining slope for plain and curve surface & 12 mm to 20 mm of

broken piece not more than 2.5CM of ceramic / glazed tiles ( one for

more colour as directed ) to be laid over cement mortar bedding of C

M 1:3 (1 cement : 3 sand ) contain water proofing materials per bag

of cement useas specified by manufactured and slops to be

tempered to bring mortar up to surface with using white cement

and colour pigment including rounding of junctions and extending

them up to 15 cm along the wall and curing with bends any patens

or design as per drawing and cleaning by using oxalic acid etc.

Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm (Green) both

are of .ISI marked 1.1 KV Grade FRLS PVC insulated multistrand copper

wires, in below type of pipe erected with 6A Modular type switch and hum

free EME four or more step type electronic fan regulator with separately

mounted and accessories with earth continuity of following type erected on

PVC / Metallic/Wooden box, single mounting base frame covered with

textured/metallic front plate modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected concealed in wall/ceiling

complete Cat. III

Point wiring for Looped Plug with 6A Modular type switch & 5 pin socket

erected on PVC / Metallic/Wooden box, single mounting base frame covered

with textured / metallic front plate modules erected on / in wall / ceiling with

following type accessories Cat. III

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V,Power Factor

9 11.00 more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, 5917.00 Ea.

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below description have shown

ranges of Wattage capacity of LED fittings.The Engineer incharge may select

any wattage capacity between the ranges shown.)(A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC line supply with over-

voltage protection. (iii) Above 60 to 90 watts Cat-|||

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

0.5 Watt assembled on single MCPCB, with housing used as a heat sink shall

be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.) (iv) 22-24 Watts, Surge -

2KV,IP-20, conventional 4 feet Cat-lll

Approved make Earth fault Relay suitable to mount with inter connection to

moulded case circuit breaker having CT ratio & MCCB rating as following

11 2.00 along with shunt trip 220V AC. with all internal connections & complete 4983.34 Ea.

erected in existing M.S.housing..

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

12 1.00 confirming to IS 13032 and BS 5486-1986 without MCB to house appropriate 248.46 Ea.

nos. of MCBs.(The DBs should be used of same company of MCB to be used)

(A) Single phase 4 way single door

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-

250 Micron galvanising, connection terminal dia of 12mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 /

meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time Necessary test report must

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Electrical Sor 2022-23 Section -3-14-9 (A)

Providing & erecting Approved make Ceiling Fan with double ball bearing ISI

mark with Condenser 230 volt A.C.50 Hz. 1200 mm sweep complete having

blades Aluminium body and blade sets having ornamental design shanks,

canopy erected with earthing [ Make shall be approved by Engineer in Charge]

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe

15 20.00 down rod erected duly painted for fan complete with proper insulation without 108.07 Mtr

leakage and earthing.

Supplying & erecting Fan Hook of 10 mm M.S. Round bar grouted in

RCC slab with Making the site as original.

Supplying & erecting fan hook box of 10 mm M.S. round bar

bounded to the RCC bars up to 50mm length each side and pierced

through a 16 Gauge M.S. box / Heavy Duty PVC box complete

erected concealed in Ceiling with necessary finishing.

Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm

18 20.00 M.S. Bolt & Nuts erected with necessary hook of 10 mm M.S. Round 98.98 Ea.

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook

OFFICE TABLE(TWO SIDE DRAWER(3) SIZE 4.00 x 2.00 feet one

side cupboard 8585.00 No.

Add 18.00 % GST

Add PMC & TPI Charges @ 3.00 %

I/We am/are willing to carry out the work at .............................................% above/below percent

(should be written in figures and words) of the estimated rates mentioned above. Amount of my/our

tender works out as under.

Estimated amount Estimated amount

Put to tender Rs……………………… Put to tender Rs………………………

Deduct .............% below Rs………… Add............% above Rs……………

Total Rs………… Total Rs……………

(*Please strike out whichever is not applicable).

will be deducted

PublicContractor's

Works Department

Bill Handbook and other specifications of Division or as directed.