SPECIAL REPAIR TO BLDG NO. 15, RS ROAD, OFFICERS MESS OF BASE HOSPITAL BARRACKPORE UNDER GE BARRACKPORE

Amount

B&R PORTION Dismantling of wall and ceiling boards or insulation boards any thickness including cover fillets etc all as specified.

Taking down of cement plaster incl hacking out of joints, hacking for key, scrubbing down with water etc in any position in multy storey building all as specified and directed.

Demolition of cement concrete as in Roofs, floor (other than ground floor) beams stair cases, landings, chajjas and similar suspended work (as in roof treatment) all as specified and directed.

Dismantling of Plain or corrugated,steel sheeting any gauge, thickness including nanital or similar pattern roof coverings all as specified and directed.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) removing unserviceable tiles to the low lying areas of defence land stone and rubbish off the premises.

Taking down of existing un-serviceable tarfelt/bituminous membrane on roof and parapet of any roof height carefully by cutting chiseling, cleaning the surface by scraping, brooming, brushing, etc and removing the rubbish from site complete all as directed by Engr-in-Charge (as in roof treatment)

Demolition of cement concrete (unreinforcement) as in ground floors or paving n. exc 15cm thick below or above ground level removing rubbish from the site of work complete all as specified and as directed.

Dismantling water tanks, capacity exc 500 & nexc 1000 Ltr and removing to store.

Dismantling wrought Iron or mild steel work of any description not otherwise provided for

Dismantling framed work for timber filletsw rail post, purlins etc under 40 sqcm in section

Demolition of Brick work or stone/boulder masonry, built in cement mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles complete all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipe 100mm internal dia jointed in cement mortar and taking out of trenches if required

Taking down Chowkhats or frame with shutters ( without taking off shutters from the frames) n.exc. 1.5 Sqm

Taking down Chowkhats or frame with shutters ( without taking off shutters from the frames) exc. 1.5 Sqm but n.exc. 4 sqm

Taking down shutter of any description exc 1 sqm and n.exc. 2 sqm each

Taking up/down steel tubning 15 mm bore

Taking up/down steel tubning 20 mm bore

S&F for framed brackets of angle or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc nexc 10 kg each brackets, confirming to Fe -29. Gde-E-165 .

S&F 2nd class HW for plain solid straight chowkat and frames wrought framed rebated on the solid rounded or chamfered put to gether with glue pinned at joint.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded both side Prelam PVC sheet colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and Prelam both side colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling ofPrelam colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at site as per specification & drawing including necessary Aluminum fitting all as specified.

S&F solid PVC Door Frame of size 50 mm X 47 mm made out of 5 mm Prelam colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing.

S&F 35 mm thick 2nd class hardwood glazed and skeleton shutter open rebated and prepared to receive glass/gangue (with sash bars) edges of forming plain chamfered or rounded fitted with cut and mitred bead for securing glass/gauged etc size of member of shutter as per Pt-I section 8 clause 8.20 (a)

M&L for 30 mm thick 2nd class hard wood glazed and skeleton shutter open rebated and prepared receive glass, gauge etc as in windows divided with square with plain chamfered rounded mitred and rebated sash bars any number complete all as specified

S&F For 2nd class hardwood 35 mm thick plain framed pannelled shutters ( two panel) with lock rail and panel of 9 mm BWP comercial ply or 12 mm veneered particle with commercial veneering on both faces klin seasoned and chemically pressure treated

M&L for steel windows factory made with side hung shutters including projecting type hinges with steel handel and steel peg stay, complete without glazing bars, dovetailed or welded all as per IS 1038 all as specified and as directed.

M&L for steel ventilators top hung shutter openable type including hinges, steel peg stay complete without glazing bars, dovetailed or welded and on coat of red oxide primer etc all as specified and as directed.

S&F for powder coated anodised aluminum frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc. complete all as specified and directed.

S&F powder coated anodised aluminium, double leaf, window and ventilator shutters, aluminium section weighing 0.55 kg /m including necessary joining cleats, glazing clips, rubber packing, anodised alumnium snap beading, screws etc. complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and fixed with aluminum beading and gaskit suitable for aluminum frames in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality and fixed with aluminum beading and gaskit suitable for aluminum frames in squares exceeding 0.5 sqm in each pane complete all as specified and directed.

M&L for 9 mm thick prelaminated particle board, inteiror grade, prelminated both side with decorative choice lamination, fixed with screws to aluminium frame work

S&F stainless steel wire cloth 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless stel wire staplesin window and door as in new door/window

S&F in repair stainless steel wire cloth 0.36 mm nominal dia. of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or stainless stel wire staples in window and door as fixed in repair as old door/window

Hacking out old broken glass (any thickness, size, quality or description) from wooden fame or ston,concrete, or brick surrounds, glazed with putty or fixed with beads, all as specified.

M&L sheet glass ordinery quality 3 mm thick and glazing with oil putty or wooden beads n.exc 0.50 sqm in each pane(upto four storey building) or all as specified.

S&F For 100 mm butt hinges medium weight cold rolled mild steel, and fixed complete all as specified and directed.

S&F For 75 mm butt hinges medium weight cold rolled mild steel, and fixed complete all as specified and directed.

S&F for Aluminum anodised barrel tower bolts of extruded section and fixed. 200 mm long all as specified and directed.

S&F for Aluminum anodised barrel tower bolts of extruded section and fixed. 150 mm long all as specified and directed.

S&F for 150 mm long aluminum handles, fabricated type, anodised all as specified and directed.

S&F for 100 mm long aluminum handles, fabricated type, anodised all as specified and directed.

S&F for aluminium alloy anodised ,sliding door bolt 300 mm long with hasp staples (bolt type) and fixing clip of sheet , cast or extruded section and fixing bolt and sliding bolt of extruded sections or cast alluminium alloy and fixed.

M&L for providing, cement concrete Type B-0 1:2:4 (12.5 mm graded aggregate) in hold fast block,lintels upto 1.5 m clear span, cills, steps: seismic and other similar bands,plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones bed plates, kerbs not provided for water trough and the like including weathering, slightly rounded for chamfered angles and throating, as directed.

S&F Bands, straps, support or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay) heavy, for large gates: hook and pintel hinges: large hasp and staple: chains: hand made sliding bolts: clamps: hold fast wall ties: hook for hanging fan: plain angle cleats for securing purlins to wood trusses or rafters: knee piece inserts : two way and three way straps, plate washers and similiar small articles confirming to Fe 290 Gde-E-165.

M&L preparing surfaces of wood and wood based materials, steel and iron work, new or old,of any description and grith, not otherwise described and Treating small articles sutch as stop, cover, gully gratings, hold fast ends of posts, back of chowkats, etc are n.exc 0.1 sqm each ditto.

S& F for 2nd class hard wood small fittings such as breckets of any type and hinge blocks, door and window stops and the like including all necessary labour articles n.exc 200 cu cm each all as specified and as directed.

M&L preparation of new surfaces of wooden surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coiat of primer all as specified.

M&L preparation of new surfaces of steel any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer all as specified.

Cutting chases in brick wall, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F steel tube medium grade galvanized with all fittings and fixed complete to walls and ceilling or laid in floor 15mm in short length

All as per item 50 above but 20 mm bore

S&F PVC 110 mm bore (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or all as specified.

S&F PVC (SWR) branch piece, single (Single Y) equal or unequal 110 mm bore with access door.

S&F PVC (SWR) junctioin single (Single T ) equal or unequal 75mm bore with access door.

S&F for PVC (SWR) Vent cowl 110mm bore

S&F in repair PVC (SWR) in 'P' trap. 125/110 mm dia.

S&F in repair PVC (SWR) in 'S' trap. 125/110 mm dia.

S&F PVC (SWR) floor trap plain with grating with 75 mm dia outlet including jointing with solvent cement

S&F PVC (SWR) reducers 100mm x 75mm bore

S&F in repair For Bib tap fancy type, chromium plated 15mm dia of bore complete all as specified.

S&F for Pillar Taps, cast copper alloy, Fancy type, chromium plated screwed, down high pressure with or without lettered Hot or cold with long screwed shanks and flynuts, screwed for iron pipe 15 mm dia and fixed all as specified.

S & F in repairs Stop valve chromium plated ,screwed down, high pressure fancy type chromium plated and fixed 15 mm dia of pipe, all as specified.

S & F in repairs Angle Stop valve Chromium plated , screwed down, high pressure fancy type long shank and cup (concealed type) 15 mm bore and fixed, all as specified.

S&F for CP over head shower multi flow W/o arm of 125mm dia with flange joints including fixing to steel pipe or union of 15mm dia as in repair.Prayag Cat No. BOS-13 or equivalent in Jaquar/Essco.

S&F in repair waste coupling of PTMT (half or full treaded ) 32 mm dia (minimum weight 32mm - 45 gms/40 mm-60 gms)

All as per Srl Item No 65 here-in-before but suitable for urinals ( Minimum weight 32mm-45 gms ) 32 mm dia

S&F in repair PVC waste pipe 32 mm dia and 80 cm long half or full threaded

S&F for PVC connection 15mm dia 450mm long with 02 Nos brass check nuts with washer etc complete all as .

S&F rotational moulded polythylene water storage tanks (1000 Ltr) (Cylindrical vertical with closed top) hoisted and fixed in position all as specified

S&F Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule/ Pvc pipe and fixed (25 mm dia).

S&F for Non skid joint free Coloured Ceramic tiles 7 to 8 mm thick (square/rectangular), area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc, set jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed

S&F for colour glzaed tiles in vertical surfaces 450x350x7mm thick set jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick cement mortar (1:4) complete all as specified and as directed.

M&L 100 mm thick cement concrete type D-2, (1:4:8) using 40mm graded stone aggregate as in sub base of footpath complete all as specified and directed.

M&L 75 mm thick cement concrete type C-2, 1:3:6 (40mm graded Aggregate) as in plinth potection or all as specified. Finished cement concrete surfaces even and smooth without using extra cement all as specified and directed.

M&L for Hardcore guage n.exc 63 mm , deposited, spread and levelled in layers n.exc 15 cm thick, watered and rolled / rammed to a true surface.Brocken stone or Boulders 100 mm thick.

M&L for Sand cushioning / filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 60mm thick Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment with glossy finish confirming to IS-15658-2006 of M-35 Grade laid over complete all as specified and directed.

S&F grating doom 100 mm dia of PTMT ( minimum weight 25gms)

M&L for rounding to edges of stone slabe such as in steps, cooking platform and other similar situations

S&F in repair CP 2 in 1 faucet including 1 mtr tube & hook all as specified and directed

S&F in repair decorative type CP pillar taps 15 mm bore cast copper alloy with capstan heads screwed down high pressure, with or without lettered "Hot" or "cold" with long screwed shanks & fly-nuits, screwed for iron pipe

S&F in repair concealed bib tap 15 mm bore cast copper alloy with crtuch or butterfly handle screwed down screwed for iron pipe or for brass ferrule fancy type

S&F in repair concealed stop valves 15 mm bore, cast copper alloy screwed down high presure, with crutch of butter fly handle screwed both ends for iron pipe or for unions

S&F in repair vitreous china wash down water closer pedestral pattern pan ( coupled closet ) white including viteous china flushing cystern, flush pipe, seat cover cistern including heavy bottel trap 12" complete set as required and specified and directed

S&F vitreous china wash basin white flat back decorative type excluding taps waste chain & plug & porcelain stopper but including brackets Make: Jaquar, cat part No QNS-WHT-7601 or equivalent make in ESSCO/PRAYAG/Century and as approved by the GE.

S& F in repair for Pelmet box 12 mm thick prelaminated particle board, interior grade,prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work or all as specified and directed..

S&F Kitchen Rack stainless steel size 610x914x254mm including taking down all as specified and directed Make Prayag, CAT No : P-336

S & F in repairs aluminium powder coated Rod 25 mm dia with fixing brackets,stops, etc fancy type. or all as specified.

S & F in repairs aluminium powder coated brackets for Curtain Rod 25 mm dia fancy type. or all as specified.

M&L Chequered cement concrete tiles 30cm x 30cm x 25mm thick glossy finished with grey cement and pigment set, jointed & pointed in neat cement slurry in floors with glossy finish over 20 mm thick screed in cement mortar (1:6) complete all as specified and directed.

S&F for joint free light shade Vitrified ceramic tiles 10 mm thick (square/rectangular) polished, light shade, area of each tile not exceeding 0.36 sqm, in floors etc, set jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed

All as per Srl item No 92 here-in-before but as in skirting over 10 mm thick plaster in cement mortar (1:4)

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exc. 6 Mtr mean radius built in cement mortar (1:4) all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) all as specified and directed.

M&L Pre-Painted Galvalume aluminum zinc coating aluminium corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/ cladding to wall fixed with 'J' and washers or screws all as specified and directed.

M&L Pre-Painted Galvalume aluminum zinc coating aluminium plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/ cladding to wall fixed with 'J' and washers or screws all as specified and directed.

M&L for 50 mm thick Cement Concrete type B-0, 1:2:4 (using 12.5 mm graded aggregate) as in Roof padding/levelling course with wpc @ 200 ml per 50 kg cement bag etc complete all as specified and directed. Note: WPC will be measured and paid in seprate item under relevent item of sch 'A' all as specified and directed.

Supply and laying of APP based modified polymeric membrane minimum 3mm thick reinforced with polyester non woven fabric 160 gms per Sqm over primed and prepared surface with transverse lap. Longitudinal lap and end lap fully torching the joints and providing protecting layer all as per manufacturer’s instruction and all the materials shall be of same make and application shall be done by authorized applicators according to manufacturer’s instructions complete over one coat of alumunum paint and including 20 mm thick screed bed in cement mortar (1:4) including water proofing compound @ 3% by weight of cement or as per manufacturer instruction and also applying one coat of cold bituminous primer over dried up surface of concrete including cleaning surface complete all as per particular specification and as directed. (Notes : (i) WPC shall be measured and paid separately. (ii) Water proofing treatment shall be done by the approved authorised applicators. (iii) Net Area of polymeric membrane shall be considered for payment purpose.)

M&L for 15mm thick rendering in cement mortar 1:4 finished even and smooth without using extra cement. mixed with water proofing compound when necessary @ 200 ml per bag Note : WPC measured and paid separately

M&L for 15mm thick rendering in cement mortar 1:6 on fair faces of concrete/wall surfaces finished fair and smooth without using extra cement.

Supply only Liquid water proofing compound.

M&L 12.5 mm thick gypsum board suspended false ceiling using anodized GI exposed ceiling suspension system with primeter channel 0.55 mm thick having web of 27mm and glange of 30mm on one end and 20mm on other end fixed to walls with the help of nylon sleeves and screws at 610mm cc intermiediate channel 0.90 mm thick having web of 45 mm and glange of 15mm on each side suspended from ceiling @ 12mm CC with GI angle 25x10x0.55 mm to be fixed to soffit with GI cleat and steel suspension fastener connecting member 0.55 mm thick having knurled web of 51.5mm and flange of 26 mm on both ends to be connected @ specing of 450mm gypsum board confirming to IS 2095, 1995 Part-I fixed with 25mm dry wall screw @ 230mm CC with screw driver with attachment including joint filling with jointing compound and finishing th exposed soffits properly with two coats of dry wall top coat ( as per recommended practices of manufacturer instructio) complete all as specfied and directed

M&L for providing and fixing stainless steel ( Grade 304) railing made of hollow tubes, channels, plates etc, including welding, grinding, buffing, polishing and making curvature ( where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of floor or the side of waist slab with suitable arrangement

M & L for Preparation of new plastered surfaces of walls and filling with wall putty and applying two coats of oil bound distemper including one coat of primer on plastered surfaces complete all as specified.

S&F for Joist, channel, flat iron, angle or tee sections, fixed independently, without connecting plates, etc (cut to ordinary length i.e within 20 mm of the length indicated) of Fe -410-W (Gde-E-250) quality A

M&L for preparation of old surfaces of steel any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer all as specified.

M & L for complete removal of existing treatment on old wall or new plastered surfaces and filled the cracks with filler materials as per manufactures instructions including washing the surfaces with water, including necessary scafolding as per site requirement and applying Two coats of exterior emulsion (weather coat ) over one coat of primer of same manufacture (of exterior emulsion paint) dustt free of approved quality including preparation of plastered surfaces on walls with wall putty finished complete all as specified.

M&L for Removing of nails, making good holes, cracks etc and applying wall care putty on walls including finished the surface even and smooth complete all as specified and as directed

M&L for Removing of nails, making good holes, cracks etc and applying wall care putty on ceiling including finished the surface even and smooth complete all as specified and as directed

M & L for Preparation of old plastered surfaces of ceiling and finished with wall putty and applying two coats of oil bound distemper including one coat of primer on plastered surfaces complete all as specified.

M&L for preparation of old surfaces of steel any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer all as specified.

M&L for preparation of old surfaces of wooden surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer all as specified.

M&L IInd class hard wood plain fillets square section secured with nails for frame work, sectional area exc 13 Sq cm and n.exc 25 Sqcm in cluding taking down all as specified

S&F for 12 mm thick venerred decorative plywood grade I ( with BWR Resin) with decorative face veneers on one faces : fixed with scress with timber framework all as specified and as directed.

M&L for preparation and cleaning of new surface of wood and applying Two coats of french polishing on surfaces of any description, width or grith including a coat of wood filler on all as specified and as directed.

M&L for preparation and cleaning of old surface of wood and applying Two coats of french polishing on surfaces of any description, width or grith including a coat of wood filler on all as specified and as directed.

M&L for preparation of new surfaces of steel any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of primer all as specified.

E/M PORTION Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete,including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and including making good the disturbed surfaces to match with existing surface and colour shade with putty at necessary holes for smooth finishing complete all as specified and directed complete all as specified and directed.

M&L for point wiring complete with 1.5 sqmm PVC insulated, FRLSH type, ISI marked,conforming to IS-694/1990 unsheathed, multistranded, single core, copper conductor cable 1100 volts grade colour code cables drawn through and including PVC Conduit 20 mm dia medium grade (MMS) and including cutting, chasing work at any height and all accessories are concealed in walls / roofs / floors / ceiling etc. flush mounting MS box with top,bottom,side/back wall knockout for conduit entry from any direction made out of 1.60mm thick suitable for fixing of modular top cover 3mm thick plate as per numbers of switch modules for modular switches, sockets, fan regulators, red colour indicator, blank plates etc as approved coloures and including 1.5 Sqmm PVC insulated multistranded FRLSH type unsheathed(Green colour),single core cable with copper conductor cable as earth continuity conductor and connecting to common earth dolly one light point controlled by one way switch and including making good the disturbed surfaces to match with existing surface and colour code including providing putty and white cement for smooth finishing of existing surface complete all as specified and directed.

All as per Srl item No 120 here-in-before but one fan point controlled by one switch and one regulator.

All as per Srl item No 120 here-in-before but one exhaust fan point controlled by one switch .

All as per Srl item No 120 here-in-before but one 5 pin 6 amps socket point controlled by one 6 amps switch on independent board .

All as per Srl item No 120 here-in-before but one 5 pin 6 amps socket point controlled by one 6 amps switch on same board .

All as per Srl item No 120 here-in-before but one bell/buzzer point controlled by one bell push.

All as per Srl item No 120 here-in-before but one light point controlled by two 2 way switches.

All as per Srl item No 120 here-in-before but but 2.5 sqmm multi stranded copper conductor with 2.5 sqmm copper earth continuity wire connected to earth duly complete for one 15A Socket on independent board all as specified and as directed by EIC.

All as per Srl item No 127 here-in-before but ,but point wiring with 4.0 sqmm and earth conductor of size 4 sqmm complete all as specified and directed.

S&F modular type switch 10 Amps, single pole,1way,1 module,240V,AC, ISI Marked complete all as specified and directed.

S&F modular type switch 10 Amps ,2way,single pole,1 module,240V,AC, ISI Marked complete all as specified and directed.

S&F modular type bell push 6 Amps,1 module, single pole, 240 volts,AC, ISI Marked complete all as specified and directed.

S&F modular type switch 16 Amps, single pole,1way,1 module,240V,AC, ISI Marked complete all as specified and directed.

S&F modular type socket shuttered type 6 Amps, 2/3 Pin combined 2 module,240V,AC ISI Marked complete all as specified and directed.

S&F modular type socket 6 A/16 Amps, 6 Pin combined shuttered socket 2 module,240V,AC ISI Marked complete all as specified and directed

S&F red color lighting indication lamp 6 Amps, single pole,240volts,AC,50 Hz suitable for 1 module ISI Marked complete all as specified and directed.

S&F modular type step fan speed regulator 100/120W, 2 module,230volts,AC, 360 degree rotation 0 to 4 steps, ISI Marked complete all as specified and directed.

S&F call bell AC, 230 Volts single pole, multi music type ISI marked, complete all as specified and directed.

S&F angle lamp holder, insulated body with back plate for batten fittings including LED lamp 10 watts complete all as specified and directed.

S&F ceiling rose, 3 terminal ,PVC/polycarbonate body ISI marked, complete all as specified and directed

S&F decorative box type 20/22 watt light fitting, blue coloured end caps, pre-wired, and including providing PVC/Wooden round/square block -02 Nos and connected with LED fitting to ceiling rose and including LED T-8 tubular lamp of 20 Watt extruded aluminium/PC body and PC diffuser complete with inbuilt LED driver with removing old unserviceable fitting complete all as specified and directed. Make of light fitting: Crompton Model No.DMLN1LT8-16/Havells Model REGALBATTENT8UPTO1X22WSSBSWH/Bajaj Model No BLRB-DB 218 or equivalent make in Philips Make of LED Rod Crompton Model No.LT8-20-865-2 / Havells Code No.PHOTONULTRA1213T8SSTL20WLED865SPC/Bajaj Model No BLRB20CW LED or equivalent make in Philips

Taking down carefully by unscrewing from ceiling rose or outlet boxes of LED tube light fittings of 20 Watt in any height or a place to be kept in safe custody and refix the same to its own position after cleaning dust particles and connections to be checked complete all as direted.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 Watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as speicifed and directed. Make : Havells/Crompoton Greaves/Bajaj

S&F wall mounted decorative type surface mounted 1x6 watt LED light fitting including fixing arrangements at any hight with nuts ,screws and washers and connected to ceiling rose and including removing old unserviceable item complete all as specified and directed. Make:-Crompton cat No.LCSR-06-CD / Surya cat No.:- SLE DLS 6W XX Stellar RD / HPL product code:-HLPLEDSO6WW as approved

S&F recess mounting 2'x2' LED 36/40 Watt light fitting slimmest 9 mm thin in class LED ceiling panel with best in class aesthetick white powder coated frame blended seamlessly with ceiling layout suitable for 600X600mm mudular ceiling grid and also can be suspended with provided kit and including connecting up with ceiling rose to fitting and including removing old unserviceable item complete all as specified and directed complete all as specified and directed. Make:- Bajaj Cat No BZRSQL36LLEDGXDWHSD / Crompton Cat No.LCPL -36-CD(2x2)/Havells Ordering code:-LHEWBPP6PW036 or equivalent in any approved make.

S&F sheet metal enclosure with metal type AD/DD,415 volts AC,VTPN DB, 4 way12 modules, flush mounting with 200amps copper busbar, 2 neutral/earth bar and MCCB incomer,FP, and MCB SP /TP as outgoing and complete for IP54 DBs protection and including making good the disturbed surfaces to match with existing surface and colour shade complete all as specified and as directed. Make: Legrand cat No.5077 30 4 way /Hager / L&T or equivalent in any approved make.

S&F SPN distribution board 12 way acrylic door 240 volts AC,SPN for flush mounting with 200 amps copper busbar,neutral bar,earth bar and MCB incomer of rating upto 200Amps ,MCB SPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat and including removing old unserviceable item all as specified and as directed. Make:- Legrand cat No.5076 21 8 Way / Hager cat ref No.VYS08G (Acrylic door)/L&T Cat ref:-DBSPN008GD or equivalent in any approved make.

S&F SPN distribution board 8 way acrylic door 240 volts AC,SPN for flush mounting with 200 amps copper busbar,neutral bar,earth bar and MCB incomer of rating upto 200Amps ,MCB SPN/DP, and MCB SP as outgoing and complete connecting cable links with top and bottom removable gland plate with IP 43 DBs protection and including making good the disturbed surfaces to match with existing surface and colour coat and including removing old unserviceable item all as specified and as directed. Make:- Legrand cat No.5076 21 8 Way / Hager cat ref No.VYS08G (Acrylic door)/L&T Cat ref:-DBSPN008GD or equivalent in any approved make.

S&F sheet metal enclosure 2 mm thick,AD/DD 240 volts AC,SPN,DB, 4 way, flush mounting with 200amps copper busbar,neutral bar,earth bar and MCB incomer,MCB SPN/DP, and MCB SP as outgoing for IP 43& IP54 DBs protection and including making good the disturbed surfaces to match with existing surface and colour shade all as specified and as directed. Make:- Legrand cat No.5076 20 4Way (AD) / Hager Cat ref No.VYS04G(AD) /L&T Cat ref:-DBSPN004GD or equivalent in any approved make.

S&F MCB SP 6 to 32 Amps 10 KA,"C" series,AC,240Volts,50Hz , ISI marked complete all as specified and directed. Make:- Legrand/Hager/Havells or as approved make

S&F and MCB SPN 40 to 63 Amps 10 KA,"C" series,AC,240Volts,50Hz, ISI marked complete all as specified and directed. Make:- Legrand/Hager/Havells or as approved make

S&F MCCB, 125A Amps,4 pole,415 Volts , 16/18KA thermal magnetic type with necessary lugs,thimbles, nuts bolts and washers and including removing old unserviceable item from existing loaction complete all as specified and as directed. Make:- Legrand cat No.4200 15 / Hager cat ref No :-HHA101U / L&T Cat No.CM91712OOKOOG or as approved make

S&F Onload Changeover Switch of capacity 200 Amp AC-23 with (I -O-II) conforms to IS IEC - 60947-3) of 415 V with SS Enclosure and fixing arrangements all as directed and specified

M & L for sub main wiring complete with 2 run of 6 sqmm single core copper conductor (ISI marked)cable 1100 volts grade, ISI marked,FRLSH type (conforming to IS-694/1990 as amended) PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit ISI marked medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 6 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, ISI marked FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade and complete all as specified and directed. Note : - Two run of 6 sqmm single core copper conductor cable and one run of 6 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

M & L for sub main wiring complete with 2 run of 4 sqmm single core copper conductor (ISI marked)cable 1100 volts grade, ISI marked,FRLSH type (conforming to IS-694/1990 as amended) PVC insulated, unsheathed,flexible,multi stranded colour coded cables drawn through and including rigid PVC conduit ISI marked medium grade(MMS) with all connected accessories such as Bend,Tee,Elbow,Short peices etc concealed in wall/roofs/floors and including one run of 4.0 sqmm single core copper conductor cable flexible, PVC insulated, unsheathed, multistranded, 1100 volts grade, ISI marked,FRLSH type as earth continuity conductor connected to common earth dolly and including making good the disturbed surfaces to match with existing surface and colour shade and complete all as specified and directed. Note : - Two run of 4 sqmm single core copper conductor cable and one run of 4.0 sqmm single core copper conductor cable as earth continuity and one run of PVC conduit shall be measured as one unit.

Supply and fix suitable for flush mounting sheet steel enclosure metal clad plug and socket including MCB SP 20 Amps, 10KA 'C 'series, 230 Volts suitable for AC's/Geysers complete all as specified and directed. Make:- Legrand cat No.5078 11 20A SP,2P+E/ Hager cat ref no.VYA120C / Havells Cat No.DHDPUSN020/L&T Cat No.DBMPS220SD or as approved make Note:- MCB SP 20Amps will be deemed to be quoted rate

Material and labour for Earthing complete with galvanised steel earth plate electrode 600mmX 600mmX 6mm thick buried directely in ground vertically ( earth pit not less than 2.25 meters deep below ground level) with top edge of plate not less than 1.5 metres below ground level, connected to and including galvanised iron wire 4 mm dia and light grade protection pipe of 15 mm dia from earth electrode up to test point or up to 7.5mtr whichever is less by means of GI bolts, nuts, check nuts and washers all as per electrical plate No 3 of SSR Pt-I and GI watering pipe of 20 mm dia medium grade,GI funnel with wire mesh,including charcoal, salt packed all around the earth electrode plate in layers, PCC earth pit chamber 1:3:6 type C1, of size (45X 45X 45) CM, RCC cover 1:2:4 type B1 of size 45X45X6 CM, excavation/earth work in any strata and returning filling, removal of surplus soil and testing/test point for required value including removing old item complete all as specified and directed.

Cutting the existing surface wall of brick/stone masonary and making round hole at any height suitable for fixing 230 to 300mm sweep exhaust fan including providing nut,bolt and washers after grouting with PCC including 3 mm dia 5cm apreature MS jali proper wooden frame to avoid trasparsing insects from out side and making good the disturbed surface area with cement and putty match with existing colour shade complete all as specified and directed.

S&F exhaust fan 250 mm sweep made of sturdy engineering plastic complete with louvers shutter , 1200 rpm, copper winding, 240Volts,AC,50Hz as approved colour and connecting of electrical connections and testing complete all as specified and directed and including dismantle old exhaust fans and shall be deposited in MES store yard of AGE(E/M), in this regard no extra payment entertained by the deptt . Make:- Havells model :- Turbo force SP / Usha model No.Turbo HDEF SPH as approved

S&F water heater storage type, electric, capacity 25 litres,BEE 5 star rated, vertical type 240 volts, AC, 50Hz and fixing arrangement on wall including providing hole fastners-04 nos, hot & cold water PVC pipes 15 mm bore approximate 600 mm long - 02 Nos, chromium plated brass stop cock 15 mm bore - 01 No and including necessary plumbing work, Anode rod, PUF insulation, 0.8 MPa high working pressure,shock safe plug with IPX protection and including necessary plumbing work, testing all as specified and directed and including dismantle old exhaust fans and shall be deposited in MES store yard of AGE(E/M), in this regard no extra payment entertained by the deptt. Make: Havells Monza Digi Cat (White) No GHWAMJSWH025/Bajaj/ Crompton Greaves

Material and labour for XLPE insulated,LT armoured electric cable with aluminium standed conductor 1100 volts grade,cross-sectional area 50 sqmm ,3.5 core laid in trenches/pipes/ducts/wall/boarings with necessary cable lugs and glands,nuts,bolts and washers etc and testing complete all as specified and directed.

Excavation in trenches not exceeding 1.5 mtr wide and not exc 1.5 mtr depth for laying of cables, pipe lines, protection pipes and foundations etc and getting out in soft loose soil complete all as specified and directed.

Returning filling in soil including spreading leveling watering and well rammimg in layer n exc 25 cm complete all as specified and directed

Removing excavated soil not exc 50 mtr ant depositing where directed at a level not exc 1.5 mtr above the starting point all as specified and directed

M & L for brick sub class 'B' 250mm x 115mm x 0.75mm and laid in trenches as in protection of UG cable complete all as specified and directed.

Supply and filling in and spreading unwashed river sand for cushioning and covering the under ground cables in trenches and punning to provide required cover complete all as specified in SSR Part-I and as directed.

S&F LED flood light fitting of capacity 200 Watt LED, light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with 4/5/10 KV inbuilt surge protector and cable connection from looping box to light fitting and testing and including removing of old unserviceable item complete all as specified and directed. Make:- Havells Cat Part No ENDURACITYLINERNEOSL200WLED757PASYBOTG Crompton cat ref No.LSFO-200-CDL/60/Bajaj Cat No.BARFEG 200W LED as approved

S&F 35/40 watts LED post top lantern made in cast aluminium spigot housing with decirative opal polycarbonate diffser and IP65 protection and providing suitable fixing arrangements such as lugs,glands,nuts,bolts and washers and including removing old unserviceable item complete all as specified and directed. Make :- Havells Cat Part No RUBYPT35WLED757PSYMTOPC/ Bajaj Model BGCL 40 W LED WH 40W LED /Crompton Cat Ref:LPTM-40-CDL as approved

S&F LED secruity light fitting of capacity 35 Watt LED street light fitting in aluminium PDC housing, toughened glass cover with IP65 protection with inbuilt surge protector and cable connection from looping box to light fitting and testing complete all as specified and directed. Make Havells/Bajaj/CG

S&F GI bracket pipe of size 25 mm dia medium grade of 1.2 mtr long bent to shape hot or cold suitable for street light fitting and making the one end of GI pipe bracket suitable for fixing of any type street light fitting and shall be fixed on PCC & Steel poles/on wall surfaces and including suitable fabricate MS flat iron clamps of 30X6 mm thick -02 Nos suitable for fixing any place of poles with nuts,bolts & washers complete all as specified and directed.

Material and labour for galvanized iron tubing 40mm dia "Medium Grade" in any length including embedded in wall two ends duly welded MS holdfast at two ends of GI pipe and providing PCC in wall and making good disturbed surfaces complete all as specified and directed.

Taking down of ceiling fan 1200/1400 mm of any make & capacity from any height overhauling of fan motor of any size and removing unserviceable grease, bearings, bushes, split pin, nuts and bolts and cleaning with petrol/kerosene applying new grease and reassembling complete including replacement of wornout spares with new like split pin, nut & bolts and material and labour for painting to ceiling fan complete body, blades & down rod etc of any sweep/make/model with two coat of synthetic enamel paint by using electric spray machine similar to match with existing colour after preparation surfaces with black paint complete and refixing the same to its original position and proper electric connection to be made and all as specified and directed. Make of paint:-Asian/Berger/Nerolac (Note:-Painting work to be carried out after dismantling of ceiling fan)

Taking down of Exhaust Fan of size 450 mm of any make & capacity from any height and removing from frame and refixing the same including removing unserviceable grease, bearings, bushes, split pin, nuts and bolts and cleaning with petrol/kerosene apply new grease and reassembling complete including replacement of wornout spares with new like split pin, nut & bolts and material and labour for painting to exhaust fan complete body, blade assembly,frame etc of 300 mm sweep /make/model with two coat of synthetic enamel paint by using electric spray machine similar to match with existing colour after preparation of surfaces with black paint complete and refixing the same to its original position and proper electric connection to be made and all as specified and directed. Make of paint:-Asian/Berger/ Nerolac (Note:-Painting work to be carried out after dismantling of exhaust fan)

Taking down of Exhaust Fan of size 300/250 mm of any make & capacity from any height and removing from frame and refixing the same including removing unserviceable grease, bearings, bushes, split pin, nuts and bolts and cleaning with petrol/kerosene apply new grease and reassembling complete including replacement of wornout spares with new like split pin, nut & bolts and material and labour for painting to exhaust fan complete body, blade assembly,frame etc of 300/250 mm sweep /make/model with two coat of synthetic enamel paint by using electric spray machine similar to match with existing colour after preparation of surfaces with black paint complete and refixing the same to its original position and proper electric connection to be made and all as specified and directed.Make of paint:-Asian/Berger/ Nerolac (Note:-Painting work to be carried out after dismantling of exhaust fan)

Taking down of Geysers of capacity 25 litres of any make & capacity from any height and dismantling from existing wall after disconnecting of electric and water supply connections to examine water tightness of inner storage tank after cleaning and renewal of rubber washer/gasket and nut,bolts and washers etc and adjust to required range of thermostat control and assembling all parts/ accessories including painting to storage type water heater(Geyser) of capacity 25 litre of any make/type to complete external body with two coat of synthetic enamel paint by using electric spray machine similar to match with existing colour after preparation of surfaces with black paint complete fixing back in same location after connecting up of water & electric connections and testing for its satisfatory functioning complete all as specified and directed.

S..S. ELECTRIC CO.

MS SHRI B.C. DAS

TAPAS BHAKAT

M/S H.P Singha

PUNAM ENTERPRISE

M/S PAUL CONSTRUCTION