Preparation of In-House Fabrication work of Various steel materials for use of Mahemdabad Division at Mahemdabad Division office store campus.

Labour charges for fabrication of HT/LT line & T/C items

from various sizes of MS Angles / Channels / Flats / MGVCL

Sr. Round bar etc. as per our requirement and as per sample Unit Rate for NOS AMT

No. code and specification with two coat of red oxide including Cost

cost of red oxide, loading, unloading stacking of all Data

fabricated item inside closed room near entry gate

1 3611000016 9'/11' (2.75/3.35 mtr.) M.S.Angle ,with 12holes No 40 500

2 2609000013 4'.6" (1.42 mtr.) Tapping Angle with 8 holes No. 19 4000

3 2609000034 11 KV 'V' Cross arms No. 56 8000

4 2609000027 2 Way LT Bracket No. 26 400

5 2609000028 4 Way LT Bracket No. 31 800

6 2609000005 2'.6" Angle Bracing with 9 holes No. 16 3100

7 3611000018 4'.6" (1.40 mtr.) Angle Bracing with 8 holes No. 20 3000

8 2609000004 2' Side Angle with 09 holes(Transformer) No. 16 2000

9 2609000032 HT Garding Angle ( 65 x 65 ) No. 21 1000

10 2601000084 HT Top fitting No. 17 6000

11 2609000022 5 Wire LT Vertical Formation No. 89 200

12 3611000029 9'/11' (2.75 /3.35 mtr.) Cross Bracing Angel No. 33 1000

13 3620000001 9' Bracing Angle from 50x50x6mm No. 22 100

14 3611000006 9' /11' (2.75/3.35 mtr.) M.S.Channel with 14 holes No. 50 500

15 2609000053 5'.8" (1.75 mtr) Channel with 7 holes No. 28 100

16 2609000051 4'.6" (1.40 mtr.) Channel with 8 holes No. 21 100

17 2609000042 11 KV 'V' Cross arms NO 73 500

18 2614000002 Anchor Rod No. 17 5000

19 2614000009 Turn Buckle No. 17 4000

20 2614000012 Eye Bolt with 2 Nos. of MS Nuts matching with Threads No.

Extension of RSJ Girder Poles from 9 mtr. To 11 mtr. Or

13 mtr., as per requirement 856 800

Fabrication of 11KV/22KV extension from V-X arm,

feet angle/Channel guy pair, top fitting 213 1000

23 2601000061 Side Clamps for RSJ Pole No. 7 14000

24 2601000069 Stay Clamp (Pair) for PSC Pole Pair 17 14000

25 2601000049 Side Clamps for PSC Pole No. 7 14000

26 2601000071 Stay Clamp (Pair) for RSJ Pole Pair 17 14000

27 2613000002 Three hole patties No. 6 400

28 2601000040 U - Clamp No. 6 4000

29 2601000050 M.S.ANGLE FABRI FOR SIDE CLAMP 200MM-8INCH. NO. 7 400

TCDP SET FROM MS ANGLE (8NOS 9FT ANGLE AND 2NOS

2FT ANGLE) 352 1050

31 3611000003 PLAIN DP SET FROM MS ANGLE (4NOS 9FT ANGLE) 160 1050

LABOUR CHARGE FOR PRAPARATION OF EARTHING COIL

FROM GI NO:-8 8000 10

TOTAL AMT WITH GST

• The Quantity shown above is an estimated and the actual may be very as per site requirement. The rates are asked above only on percentage basis against

estimated amount. The tender offer must be specify the percentage (%) either above or, below to the estimated amount. And it should be clearly specified both

in figures and words

The rates are asked above only on percentage basis against estimated amount i.e. item wise rates stated in the Schedule-B. The tender offer must be specify the

percentage either above or, below to the estimated amount and it should be clearly specified both in figures and words. Above quantity are approximate and

may vary as per requirement.

a) The rate for dismantling work of any item, not mentioned above, will be given half of rate of erection work.

b) All dismantled material should be credited to concern Sub Division store.

c) Contractor has to produce sufficient quantities of the gangs as per the target requirement of particular S/dn

d) Above Schedule - B quantity may very as per actual work involvement.

e) Rates are including cost of M.S. Bolt-Nut.

Seal & Sign of Executive Engineer

Contractor with Rubber Stamp MGVCL, Mahemdabad Division