Construction of Toilets at HWPM colony under Swachhata Action Plan.

Amount

Providing required men, machinery, tools & tackles for Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth 1.5 m in width as well as 10 sqm on plan) including backfilling of the same after completion of work and disposal of excess earth lead upto 1.05 Km and lift upto 3.0m, disposed earth to be levelled and neatly dressed etc., all complete as per specification and as directed ny the Engineer in Charge. (Note-Including dewatering)

Depth upto 1.50m below GL

Supplying, Diluting and injecting chemical emulsion for PRE-CONSTRUCTIONAL Anti-Termite Treatment of soil using Termex (Imidacloprid 30.50% SC) solution (2.1ml Termex to one liter water) @ one litre per hole, 300 mm apart including drilling of 12 mm diameter holes etc., as per specifications and as directed by the Engineer in Charge.

Providing and laying Plain cement concrete of 1:2:4 (1 cement: 2 sand: 4 stone aggregate) grade, using 40mm and down gauge crushed stone aggregate of approved quality, 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make in foundation and plinth, under floors, pavements, footings, pedestals etc., including centering and shuttering, spreading, leveling, ramming, finishing, curing etc., all complete as per specifications and as directed by the Engineer.

Providing and laying in position Reinforced cement concrete of grade 1:1½:3 (1 ordinary portland cement 43grade : 1½ coarse sand : 3 graded crushed stone aggregate 20 mm nominal size) cement is of ACC/ Ultratech/ Birla A1 or any other approved make (cementious content as 400 kg with cement flyash ratio of 70:30 (70% cement : 30% fly ash, flyash available free of cost at DFA silo area in plant site but transporting by the contractor)) minimum cement content excluding fly ash should be 280 kg/cum, , RCC work upto floor V level including cost of Centering/ Shuttering, compaction, levelling, finishing and curing but excluding the cost of reinforcement etc., all complete as per specifications and as directed by the Engineer in Charge.

Upto plinth level

Above plinth & upto floor V level

Providing, laying and fixing in position TMT reinforcement bars of grade Fe415D/ 500D of TATA/ JINDAL/ SAIL/ VIZAG or equivalent make for RCC works, including cost of supplying, cutting, bending, transporting, erecting, binding with 16 gauge MS annealed wire, cement mortar spacer blocks etc., all complete as per specifications and as directed by the Engineer.

Providing and laying Brick masonry work with non modular Fly ash bricks with CM 1:6 (1 Cement : 6 Coarse sand) using 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level including cost of scaffolding etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and laying half brick masonry with Flyash lime brick masonry of class 7.5 designation in CM 1:4 (1 cement : 4 coarse sand)using 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make in super structure including curing, provision of scaffolding etc., all complete as per specifications and as directed by the Engineer.

Providing and laying 6mm thick cement plaster of 1:3 (1cement : 3 fine sand) using 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make for ceiling of roof over a concrete wotk to give even smooth finish including cost of scaffolding where ever required and curing etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and laying 12mm thick cement plaster of 1:4 (1cement : 4 fine sand) 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make ,upto floor V level over a brick work/ concrete wotk to give even smooth finish including cost of scaffolding where ever required and curing etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and laying 18mm thick water proof cement plaster in two coats under layer 12mm thick cement plaster 1 : 5 (1 Cement : 5 coarse sand) and a top layer of 6mm thick cement plaster 1 : 3 (1 cement : 3 Fine sand) using 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make and approved water proof compound as per manufactures specification in both the coats and finished smooth with a floating coat of neat cement with water proof compound including racking of joints, hacking concrete surfaces, scaffolding, curing etc., all complete as per drawings, specifications and as directed by the Engineer in Charge. (Liquid water proofing compound of M/s SIKA or equivalent proportion 1.50 Kg/50kg bag of cement)

Supplying and filling in plinth with coarse river sand under floors, including watering, ramming, consolidating and dressing complete as per specifications and as directed by the Engineer in Charge.

Providing and laying first quality Anti skid Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and Making Plinth protection of 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) using 43 grade OPC cement of ACC/ Ultratech/ Birla A1 or any other approved make ,over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling, dressing & finishing the top smooth etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and applying two or more coats of Distemper with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, including applying additional coats wherever required to achieve even shade and colour of Asian/ Nerolac or approved make and brand over a coat of water thinnable cement primer including scraping, cleaning, preparing wall surface, having VOC content less than 50 grams/litre including all materials, labour, transport, scaffolding as and when required etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and applying Two or more coats of acrylic smooth exterior coating of Apex Ultima of M/s. Asian Paints/ Excel of M/s. Nerolac/ Heatshield of M/s. O.FIXIT/ Weathershield Max of M/s. ICI Delux or equivalent make and to give even shade & finish over the new wall surfaces, applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied@ 2.20 kg/ 10 sqm), ensuring an interval of 4-6 hours for each successive coats etc., all complete as per specifications and as directed by the Engineer in Charge.

Supplying, fabricating and fixing of structural steel work in builtup sections of make VIZAG/ SAIL/ TATA/ JINDAL or equivalent make (round, square or rectangular hollow tubes, plates , bolts.) etc., including cutting, hoisting, fixing in position and applying two coats of synthetic enamel paint over a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete as per drawings, specification and as directed by the Engineer-in-charge.

Providing and fixing factory made 30 mm thick non Decorative finish door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer, all four corners of reinforcement to be welded or sealed.Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm including providing & fixing of aluminium grade AC 10 as per IS : 1868 Aldrop of size 250mm x 16mm - 1No, latch 250mm x 20mm x 6mm - 1 No and door handles of 125mm size - 2 No's, Powder coated MS Tower bolt of size 200mm x 10mm - 1No etc., complete all as per manufacturer's specifications and direction of Engineer-in-charge.

Providing and fixing white vitreous china European type water closet conforming to IS 2556 (part 1) of with integrated 'P' or 'S' trap, IC extension piece if required including Thermoplastic seat and cover conforming to IS : 2548 with C.P. brass hinges and rubber buffers, providing and fixing of 10 litres capacity low level white PVC flushing cistern with manually controlled device conforming to IS : 7231 with 38 mm dia PVC flush pipes and overflow pipe with specials and mosquito proof coupling of approved make (Hindware/ Parryware/ Cera or equivalent approved make) and with all fittings, fixtures and brackets etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests with 100 mm uPVC "P" or "S" trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures (Hindware/ Parryware/ Cera or equivalent approved make) complete, including cutting and making good the walls and floors wherever requiredall complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing white vitreous china flat back half stall urinals of Range of two , each of size 580x380x350 mm with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing stone slab table rubbed, edges rounded and polished of Granite Stone of approved shade,size 75x50 cm deep and 1.8 cm thick fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth etc complete and as directed by the engineer.

Providing and fixing White Vitreous China Wash basin of size 630mm x 450 mm including a single 15 mm C.P. brass pillar tap, fixing with C.I. brackets, 32 mm C.P. brass waste coupling of standard pattern, painting of fittings and brackets, cutting and making good the walls wherever required etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing G.I. Pipes of following sizes of class B confirming to IS:1239, with ISI mark embossed of M/s.TATA/JINDAL make complete with G.I. fittings and clamps, concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall etc., all complete as per specifications and as directed by the Engineer in Charge.

25 mm dia nominal bore

20 mm dia nominal bore

15 mm dia nominal bore

Providing and laying 110mm dia best quality uPVC pipes and specials in trenches for all depths to correct grade, levels, alignment and slopes, jointed with hemp yarn and cement mortar 1:1 on 100mm thick bed and covered alround with cement concrete 1:4:8 using 40mm and down gauge stone ballast of approved quality (exclulding pipe portion embedded in masonry), including curing, testing, excavating the trenches, back filling, form work etc., all complete as per specifications and as directed by the Engineer in Charge.

providing all tools tackles manpower material machinary required for placing in position 100mm cast iron gully / nahani trap as per IS 1729 with SS grating plate etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing 15mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 etc., all complete as per specifications and as directed by the Engineer in Charge.

Providing and fixing square-mouth S.W gully trap class SP1 complete with C.I grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight ofcover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design 100x100mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with non modular Fly ash bricks in cement mortar 1:4 (1 cement : 4 coarse sand) conforming to IS:12894, class designation 10 average compressive strength, C.I. cover with frame (light duty) 600x 850 mm internal dimensions and 45 cm deep for pipe line with three or more inlets, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc., all complete as per standard design, specifications and as directed by the Engineer in Charge.

K.NARASIMHULU CIVIL COTRACTOR

SHRAVANI CONSTRUCTIONS

M/s AYESHA CONSTRUCTIONS

SUGUNA CONSULTATIONS