PROVN OF GD ROOM FOR 8 PERS AND SENTRY POST FOR OLD MT ACCN AND PROVN OF BOUNDARY WALL AND STEEL GATE AT OFFR MD ACCN SARAGARHI COMPLEX AT PALAMPUR MIL STN

Amount

Surface excavation n exc 30cm deep and averaging 15cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed .

M&L PCC 1:4:8(nominal mix) type D-2 (using 40 mm graded crushed stone aggregate), as in foundation filling and mass concrete, complete all as specified and directed.

Use and waste of formwork to sides of concrete foundation,footing,bases of columns,rafts and rafts beams ,sides and soffits (if any) of foundation and plinth beams and similar work ,vertical or to batter for rough finished surfaces of concrete complete all as spcified and directed.

Formwork to sides of pillars , posts, struts, piers, columns and stanchions of square,rectangular or polygonal fair finished surfaces of concrete. Complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams flat for fair finished surfaces of concrete , complete all as specified and directed.

Use and waste of formwork to soffits of flat suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and as directed.

M & L for reinforced cement concrete M-25(20mm graded aggregates) design mix in foundations ,including rafts , footings,foundation beams,plinth beams,bases for column,etc basement slabs,under reamed piles and mass concrete.complete all as specified and directed by Engr-in charge.

M&L RCC M-25 (using 20mm graded stone aggretate) design mix in columns ,pillars,piers,post and struts ,all as specified and directed.

M&L RCC M-25 design mix (using 20mm graded stone aggregate) as in beams, cantilevers, bressumm- ers, lintels over 1.5m span all as spcified .

M&L RCC M-25 design mix (using 20mm graded stone aggregate) as in slabs supported on walls , beams, and columns in floors, roofs landings, balconies, canopies, deck slabs and in shelves and the like.all as spcified .

M & L TMT bar 10 mm and over cut to length, bend to shape required including cranking, bending spirally for hoopings for cols, hooking ends and binding with ad including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M & L TMT bars 5mm dia and over upto and including 10mm dia as in stirrups cut to length bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with and incl mild steel wiere (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L Brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

M&L rendering 10 mm thick CM 1:6 on brick or concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

M & L for Rendering 15 mm thick in two coats i.e. 10mm thick in CM 1:6 and 5mm thick in CM 1:4 using water proofing liquid compound as per manufacturer's instructions on other than fair faces brick or concrete surfaces and finishing surfaces even & smooth without using extra cement complete all as specified and directed. Note :- Water proofing liquid compound shall be measured and paid separately.

Supply only liquid water proofing liquid complete all as specified and directed.

M&L for two coat of oil bound distemper over priming surface with chalk whitening on plastered ,prepatory to distempring to new plastered surfaces including preparation of wall surfaces complete all as specified and directed.

M&L preperation of new surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified.

M&L two coats of white wash on ceiling including preparation of new plastered surface complete all as specified and directed.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated stee sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

M&L Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc confirming to Fe 290 ( gde E-165) all as specified.

Roof trusses (framed) , trussed, purlins, crane gentries, rails and fastening and heavy bracket framing(Beam, tee, angle , channels, or flat sections) including distance pieces, cleats etc of Gde E-250 A quality Fe-410-W, Complete all as specified and directed by Engr-in Charge. (Note:- The weight of cleats, brackets, packing pieces, distance pieces, gusset plates, fish plates etc over 10 Kg shall be added to the weight of respective item.)

M&L framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc, n exc 10 Kg each brackets, confirming to Fe. 290 Gde-E-165 (Brackets over 10 Kg each to be measured under structural Steel)

M&L mild steel bolts.purpose made dia exc 12 mm and n exc 20 mm. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30 cm long complete all as specified and directed.

M&L mild steel bolts.purpose made dia n exc 12 mm. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30 cm long complete all as specified and directed.

M&L reparation of new steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome primer, complete all as specified and directed by engr-in-charge.

Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as specified and directed.

M & L for hard core broken stone of gauge n.exc 63 mm deposited , spread and levelled in layers n.exc 15 cm thick, watered rammed to a true surface complete all as specified and directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded agg) as in Sub base all as specified and directed .

M&L 25 mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in floor finished even and rought to received the topping layer complete all as specified and directed.

M & L for providing 75mm thick PCC (1:2:4) type B-2 using 40mm graded stone aggregate as in plinth protection including finishing the surface of concrete topping even & fair, without using extra cement complete all as specified.

M&L Non skid ceramic white tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete complete all as specified and directed.

M&L Non skid ceramic white tiles 7 to 8mm thick (square /rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L Coloured Glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over cement plaster 10 mm thick in CM 1:4 complete all as specified and directed.

S&F, 110mm bore, PVC rainwater (SWR) drainage pipes single socketed, in any length with rubber ring joints , fixed to walls complete all as specified and directed.

S&F, 110mm bore, PVC rainwater (SWR) drainage pipes single socketed, in any length with rubber ring joints laid in trenches, complete all as specified and directed.

S&F for 110mm bore PVC (SWR) bends any radius fitting fo PVC (SWR) pipes, complete all as specified and directed.

S & F110 mm PVC (SWR) vent cowl ,complete all as specified.

M&L 75mm PVC floor trap, with grating including jointing with solvant cement.complete all as specified and directed.

S&F, 75 mm bore, PVC rainwater (SWR) drainage pipes single socketed, in any length with rubber ring joints laid in trenches, complete all as specified and directed.

M&L 75mm PVC Bends (any radius) complete all as specified and directed.

S & F 110 mm PVC (SWR) 'P' Trap fixed to PVC pipe and water closet any type, complete all as specified and directed.

S&F pressed steel frames for door made out of MS Sheet 1.25mm thick of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc all as specified and directed.

S&F pressed steel frames size 105mm x 60mm for doors with one or more rebates including necessary fixing lung, hings, lock strike plate etc. complete all as specified.

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and drawing as per SSR Pt-II 2010 complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

S&F 35 mm thick plain framed panelled door shutters of 2nd class hard wood (Factory made) two panel with lock rail and panel of 9mm thick BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 Part-I, Kiln seasoned and chemically pressure treated, fitted to chowkats complete all as specified and directed.

S&F 35 mm thick 2nd class hard wood plain framed factory made glazed and skelton shutters open rebated and prepared to receive glass/ wire gauge etc (without sas bars)edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for secring glass,etc size of members of shuters as specified in SSR Part-I,Section 8, clause 8.24 (a) all as specified.

S&F factory made solid PVC moulded door shutter with wood free EPS 28 to30mm thick(stiles) with 2 4 or 6 panels design with 2mm thick moulded prelam PVC sheet on the front face and 2mm prelam PVC sheet on back face supplying and fixing in frame at site asper specifications and drawings as per SSR Pt-II 2010 complete all as specified and directed.

S & F floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed in floor over all length of cover plate 140mm thick complete all as specified and directed.

S&F butt hinges 100mm, cold rolled medium weight mild steel all as specified.

S&F 125mm size, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 150mm long aluminium tower bolts (ISI Marked) extruded type all as specified.

S&F 300mm, Mild steel spring for door, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified.

S&F 300 mm size brass sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed by Engineer-in-Charge.

S&F Galvanised mild steel wire cloth 0.56mm of nominal dia of each wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

M&L preparation of new wooden surfaces of any description exc over 10cm with or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Providing and fixing tiled false ceiling of size 595 x 595mm in true horizontal level suspended on interlocking gypric metal grid of hot dipped galvanised steel section (galvanized @ 120 gsm/sqm, both side inclusive) consisting of 3600mm long main 'T' runner size 24x38mm and 0.30mm thick,1200mm long cross 'T' of size 24 x 25mm and 0.30mm thick, 600mm secondary cross 'T' of size 24 x 25mm and 0.30mm thick, bottom exposed capping of width 24mm of all T-sections shall be of 0.25mm thick PPGI, wall angle is fixed along the perimeters of the ceiling to walls, partitions or columns etc with rawl plugs and wooden screws at 300mm centers Main 'T' runners are then suspended from ceiling using GI sloted cleats of size 27x37x25x1.6m fixed to ceiling with 8mm dia and 45mm long dashfasteners, 4mm GI adjustable rods with galvanised buttrtfly level clips of size 85x30x0.8mm spaced at max 1200mm centre to centre along main 'T' and not more than 150mm from spliced joints.The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall, then 1200mm long cross 'T' is interlocked between the main 'T' at 600mm center to center to form a grid of 1200x600mm and then secondary cross 'T of length 600mm is then interlocked at middle of the 1200x600mm grid to form grids of 600x600mm. Cross tees at the ends having length more than 600mm are to be supported independently. Finally white coloured Gyproc 8mm thick Dew Drop/Granular tiles of size 595x595mm having foil on backside & PVC paper on front side wrapped around edges to be placedin grid complete all as specified and directed., complete all as specified and directed by Engineer-in-Charge.

S & F Anodised aluminium three parallel tracks within the frame, allowing for three sliding panels for window and ventilator (two panels fixed with ordinary quality glass of thickness 5 mm and one panel fixed galvanised mild steel wire cloth 0.56 mm of nominal dia of each wire and average width of aperture 1.18 mm) (powder coating of any colour and thickness not less than 50 micron) aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as multi point lock,glass sealant etc, complete all as specified. Note:- The rate includes Three track frame , Three No panels(2 glass and 1 wire cloth including 5 m thick glass and wire cloth as described in item description)

M&L RCC Nominal mix 1:2:4 type B1(using 20 mm graded aggregate) in chajjas complete all as specified and directed by engr in charge.

Formwork to flat chullah hoods,chajjas,troughs and similar items including edges fair finished surfaces,complete all as specified and directed.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M & L Granite 20mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15mm, all as specified.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings(such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs,unions etc.) of nominal bore 20mm, all as specified.

S&F 20mm dia gun metal ,globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed.

S&F Vitreous China wash down water closet pan and trap, (pedestal pattern) (Fixing includes bolts, 'P' and 'S' trap and connecting to drain pipe, white seat cover plastic flat bottom and MS Chromium plated hinging device and connection to flush pipe, flushing cistern and also polyethelene flushing pipe) etc complete all as specified and directed.

S&F PVC 10 Ltr valveless,syphonic action type , flushing cistern, low level,white inlet, ball valve, float and handle including bracket and & supply of flush pipe of polyethylene of low or high density or PVC , 32 mm dia for low level cistern & supply of plastic water closet seat cover white , closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F, Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand of size 630x450 mm ,including brackets and waste pipe complete all as specified.

S&F health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in pipe complete all as specified and directed.

S&F CP jet spray hygenic spray jet for 15mm bore dia fittings 1 to 1.5m long tube acrylic type complete all as specified and directed.

S&F vitreous china Urinal half stall type white with spreader etc, complete including making good complete all as specified and directed.

S&F 15mm bore Angle valves, CP fancy type (ISI marked) one way/ two way screwed down, high pressure with crutch or butterfly handle, screwed both ends (externally threaded) complete all as specified and directed.

S&F concealed type with wall flange, stop valves 15mm bore, cast copper alloy, fancy type cromium plated screwed down, high pressure, with carutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F soap dish dish type of milld steel Chromium plated and wooden/plastic cleats complete all as specified and directed.

S&F 15mm bore CP Bib taps, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F 15mm bore CP pillar taps, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified.

S&F brass chromium plated mixture for mixing hot and cold water for Bath/WHB(including one end for shower connection including end connection to shower pipe), screwed down for iron pipe for 15mm dia bore pipe, complete all as specified and directed by Engineer-in-Charge.

S&F Chromium plated toilet paper holder standared quality complete all as specified and directed.

S&F brass chromium plated shower rose 125 mm size with swivel joints including fixing to steel pipe or union complete all as specified and directed.

S&F brass cromium plated tubular towel rail, 20mm dia, 'D' type, 60cm long between flanges complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank 500 ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position with PVC float ball valve 20mm dia with polythene float and fly nut, tank nipples with check nuts and washers complete and making connection with existing water supply line complete all as specified and directed.

S&F 25 mm Stainless Steel drapery rod with a pair of stainless stell coated M S clamp to hold drapery rod and decorative attachment at one or both ends of drapery rod fixed in opening door/window (each opening n exc 1.50m contained with a pair of clamps and a pair of side ornament attachments) complete all as specified and as directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 using water proofing liquid compound as per manufacturer's instructions and surface finished even and smooth without using extra cement complete all as specified and directed.

Applying bitumen primer for use in waterproofing and damp proofing treatments, complete all as specified and directed.

Bitumen hot blown VG 20 of paving grade (60-80 penetration) applied hot, two coats over primed concrete surfaces at the rate of 1.5 kg per sqm per coat. Complete all as specified and directed.

APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove febric (wt. not less than 150 gms/sqm) land on primed surface by forced appplication complete all as specified

Returning filling in with approved excavated earth, incl spreading leveling, watering and well ramming in layers n exc 25 cm thick with soft loose soil complete all as specified and directed.

Removing excavated material n. exc.50mtr and depositing where directed at a level n. exc. 1.5m above the starting point all as specified.

M&L PCC 1:3:6 type C-2 (using 40mm graded aggregate) in foundation, filling and mass concrete complete all as specified and directed.

M&L Brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:3 complete all as specified and directed.

M&L rendering 15mm thick plaster on other than fair faces of brick work or concrete surfaces in CM 1:4 and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for pre cast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in landing,cover slab etc including necessary formwork set in cement mortar 1:4 complete all as specified and as directed.

M&L for cement concrete bed to drain pipes of thickness 100 mm and width 450 mm incl packing under and haunching against the sides of 150 mm bore drain pipes after they are laid and tested in cement concrete type D-2 ,1:4:8 (using 20mm graded aggregates) complete all as specified and directed.

S&F, for 150 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

On site CONVENTIONAL type LLDPE septic tank of capacity 1000 ltrs designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for 5 users.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 1.8 M dia X 3.0 M effective depth.

Excavation over area not exc 1.5 m deep in any type of soil and getting out complete all as specified and directed

All as per item no 106 but additional 1.5 m or part therefor in depth beyond 1.5 m in any type of soil.

M&L plain cement concrete 1:2:4 type B-0 using 12.50 mm graded stone aggregate cast in situ in lintels up to 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings up to 60 cm in height, copings, kneelers, apex stones, bed plates, water through and the like including weathering, slightly rounded or chamfered angles and throating including use of form work (straight or curved) complete all as specified & directed.

M&L Brickwork with old size sub class 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 complete all as specified and directed.

M&L rendering 15mm thick plaster in cement mortar 1:4 on fair faces of brick surfaces or concrete surfaces ,surface finished even and smooth without using extra cement complete all as specified .

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails,braces etc. Complete drilled for fixing of steel sheeting or other covering . Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete in Fe 410 -W (Gde-E-250)Quality A.Complete all as specified and directed.

S& F 1.25 mm thick Mild steel ,plain, black sheet in wall cladding, steel gates and similar work cut to size, holes punched:, including round head screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seems, including bending or turning up, mitred anglesetc as required

S& F Bands ,straps, supports or stays for rainwater , ventilating pipes including bolts, if required hooks(stays), heavy, for large gates; hooks and pintle hinges; large hasps and staples; chains ,hand made sliding bolt; clamps hold fasts, wall ties; hooks for hanging fans;plain angle cleatos for securing purlins etc all as specified and directed by Engr -in Charge

M&L for point wiring with 1.5 Sqmm (nominal area) PVC insulated FRLS and unsheathed multistranded copper conductor cable 1100 volts grade drawn through and including PVC rigid Concealed conduit not less than 1.8 mm thick (ISI marked) with all accessories including bends, cross, elbows tees etc of suitable size including concealed MS pressed steel (Modular sunken box) terminal box not less than 1.6 mm thick for mounting switches, sockets, fan regulators etc and Modular cover plate as top cover (ISI marked) including 1.5 sqmm PVC FRLS insulated unsheathed copper conductor multi stranded cable for continuous earth conductor connected to common arth dolly , complete all as specifid and directed for the following :- Note- (a) Proper colour coding is to be followed as per IS specification. (b) Point wiring considered for Modular switches and sockets, rate of metallic sunken box and modular sheet cover plate and other connected accessories (of any size 1 to 12 way as per site requirement) required for modular point wiring included in quoted rate. (c) Rate of modular switch and sockets will be paid seperately under relevant item.

One light controlled by one switch 5 Amp , SP , one way 240 volts

One Ceiling /Exhaust fan point controlled by one switch SP , one way, 5 Amp , 240 volts.

One multi pin socket outlet 5 amp independent board.

One multi pin socket outlet 5 amp same board .

All as per the description of Serial Item No. 114.00 above but using 2.5 sqmm (nominal area) multistranded copper conductor cable & 2.5 sqmm size PVC insulated FRLS and unsheathed copper conductor cable FRLS for earth continuity (green colour) for one 3 pin socket outlet 15 Amp multipurpose independent point controlled by 16 Amps switch ,SP ,one way ,240 volts for socket ,complete all as specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed.

S&F Modular Switch one way 6 Amp, one module 240 volts ISI marked complete all as specified and directed.

S&F Socket, 16A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and directed.

S&F modular switch one way 16 Amp, one module 240 volts ISI marked complete all as specified and directed.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete all as specified and directed.

S&F LED Bulb 09/10 watt with provision of fixed in Lamp holder complete all as specified and directed.

S&F LED 'T' Type Mirror light fitting 09/10 watt with provision of fixed in Lamp holder complete all as specified and directed.

S&F LED bulk head 10W with pressure plastic housing with clear prismatic diffuser, high efficient LEDs IP66 complete all as specified and directed.

S&F decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S & F factory made DB SPN 8 way double door with 200 Amps rated bus bar concealed in wall IP 42/43 protection, 240V for fixing MCB & making good to disturbed surfaces as well as matching with existing whitewash color/surfaces complete all as specified and directed. Note: Distribution board and MCB's should be same make. .

S&F 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity SP 6 to 32 Amp, in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S &F SPN 40 Amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F new electric storage Heater (vertical type Geysers) 50 Ltrs BEE RATING 5 STAR, 230 volts AC single phase with and including grouting with high tensile rag bolt, nut & washer etc as directed as per site requirement and making necessary inlet / outlet water connection for Geysers. Geysers to have glass lines tank, fero glass coated container, PUF insulation, glass coated heating element, thermostat cut off etc. complete all as specified and as directed.

S&F sheet metal enclosure, single pole and neutral with a two pin and earth plug and socket with and including one single pole MCB 20. Amps, 240 volts, 10 KA complete all as specified and directed.

S&F Exhaust fan made of Strudy Engineering plastic complete, AC single phase, 230V of size 250 mm sweep with blades, and frame and Louvers, energy saving including cutting of wall all as specified and directed by Engr - in - Charge.

S&F celling fan 1200 mm sweep complete all as specified

S&F wall mounted fan 450 mm sweep complete all aspecified

M&L earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 Sqmm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

Supply, laying and testing cable XLPE insulated screend PVC bedded, galvanised steel strip or wire armoured electric power cables (Heavy duty) 1100 V grade with stranded aluminium conductor of size 25 sqmm x 2 Core, laid in trenches or passing through pipe including taking down of existing cable/service connection of any type or size and removing from site to MES store for reuse if serviceable or for credit all as specified and directed and directed by Engr-In-Charge.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete all as specified and directed.

Brick, old size sub class 'B' laid in trenches with width wise along the alignment of the cable as protection complete all as specified and directed.

S&F tube light grade galvanised with all fitting laid in trenches, fixed to wall and floor of 40 mm dia for cable protection complete all as specified and directed.

S&F tube medium grade galvanised with all fitting laid in trenches, of 20 mm dia complete all as specified and directed.

S&F tube medium grade galvanised with all fitting laid in trenches, of 25mm dia complete all as specified and directed.

S&F tube medium grade galvanised with all fitting laid in trenches, of 40 mm dia complete all as specified and directed.

S&F tube medium grade galvanised with all fitting laid in trenches, of 50 mm dia complete all as specified and directed.

S&F 15 mm bore gun metal, globe or gate valve, heavy duty confirming to IS -778 with iron wheel head, screwed both ends for iron pipe complete including taking out old un-serviceable one all as specified and directed.

S&F 20 mm bore gun metal, globe or gate valve, heavy duty confirming to IS -778 with iron wheel head, screwed both ends for iron pipe complete including taking out old un-serviceable one all as specified and directed.

S&F 40 mm bore gun metal, globe or gate valve, heavy duty confirming to IS -778 with iron wheel head, screwed both ends for iron pipe complete including taking out old un-serviceable one all as specified and directed.

M&L construction of valve pit of inner sizes up to 60 cmx 60cm x 60cm brick masonry construction complete All internal surface and external surface upto 15 cm below normal ground level of brick masonry shall be plastered 15mm thick in cement mortar 1:4, finish even and smooth including necessary excavation and earth work in any type of soil,metal sheet cover with proper angle iron frame and PCC work all as per TD drg complete all as specified and directed.

M/s ASS Construction Co (BID ID -3460088)

M/S ER CONSTRUCTIONS (BID ID -3465733)