Construction of Science lab in Govt Senior Secondry School at Rakoh in Tehsil Sarkaghat Distt. Mandi (HP

Amount

Excavation in foundations, trenches etcetera in all classification of soil dry in or saturated conditions upto any depth and lift includung pumping and bailing out water where required including stacking the serviceable and unserviceable materials seperately as directed and then returning the stacked soil in fifteen centimeters layers when required into plinth and sides of foundation etcectra consolidating each deposited layer by ramming and watering and then disposing of all surplus un-serviceable excavated earth within all leads and lifts as directed by the Engineer-in- Charge including carriage of materials in all leads and lifts disposed materials to be neatly levelled.

Excavation in drain and channels etc. in all kinds of classification of soil Viz,such as pick work, Jumper work, blasting work and hard blasting work saturated soil including dressing of side and bed disposing of excavated earth upto any lead and upto any lift as per the diraction of the Engineer-In-Charge disposed earth to be levelled and eatly dressed within all leads and lifts.

Providing from work with mild steel plates 3.15mm (Three point one five millimeter) thick welded with angle iron in frames 30x30x5mm(Thirty into thirty into five millimeter ) so as to give a fair finish including centering, shuttering, strutting , propping and centring with wooden battens and ballies in all heights below supporting floor to celling and removal of the same for insitu-reinforced concrete and plain concrete work, including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge .

In foundation,footings bases of columns and mass concrete including plinth beam

Flat surfaces such as soffits of the suspended floors roofs, landing,shelves and the like etcetra in all thickness in any floor level.

Vertical surfaces such as walls and thickness partitions and the like including attached pillasters, buttresses, plinth and string courses and the like.

Columns,pillars,posts and struts square rectangular or polygonal in plan in any floor.

Stair case with slooping or stepped soffit excluding landing.

Beams, cantilever, girder and lintel, sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels in any depth in all heights from floor.

Providing and laying cement concrete 1:6:12 (One cement :six sand: twelve graded crushed stone aggregate) 40mm(Forty millimeters) nominal size ,mixed and vibrated mechanically and curing complete excluding cost of form work in foundation and plinth including entire carriage of materials in all leads and lifts as per direction of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (One cement: four sand: eight graded crushed stone aggregate) 40mm (Forty millimeters) nominal size and curing complete excluding cost of form work in foundation and plinth including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge.

Providing and laying rainforced cement concrete design mix M-25 (twenty five) grade mechanically mixed and vibrated and curing complete excluding cost of form work and reinforcement for reinforced cement concrete work. The mix shall be design as per requrement of I.S code and PWD specification. The design mix will be got approved from the Engineer-in Charge prior to the cashy. The thoriual consumption of cement for the item shall be worked out as per approved design mix as per I.S code including carriage of materials with in all leads and lifts and other incidentals.

Foundation footing bases of columns and the like in mass concrete.

Suspened floors, roofs, landings, shelves and there support balconies, beams, girders, bressumers and cantilevers upto all floor level

In columns pillars, posts and struts upto all floor level

Stair case (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto all floor level

Providing and laying upto all floor level reinforced cement concrete 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty millimetre) nominal size to give smooth and even surface including centring and shuttering etc. but excluding cost of reinforcement in mouldings as in cornices windows sill etc. not exceeding 15cm (fifteen centimetre) in girth including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge.

Providing and laying cement concrete 1:2:4 (one cement: two sand: four graded crushed stone aggregate 20mm (twenty millimetre) nominal size) mechanically mixed and vibrated including curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of material within all leads and lifts and other incidentials.

Walls (any thickness but not less than 0.10 metre thickness) including attached pilasters buttersses, plinth and string courses etc. from top of foundation upto all floor level.

Suspended floor, roofs landing and shelves and their support, balconies, beams, girders, bressumers and cantilivers upto all floor level

Providing and laying tor steel reinforcement for reinforced cement concrete work including bending , binding and placing in position complete in all heights including cost of binding wire and including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge.

Providing in reinforced cement concrete work smooth finishing of the exposed surface with cement mortar 1:3 (one cement : three sand) including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge.

Brick work using second class common burnt clay building bricks in super structure above plinth level upto all floor level in cement mortar 1:6 (one cement : six sand) upto all floor level including curing complete and carriage of material within all leads, lifts and other incidentals.

Half brick masonry using second class common burnt clay building bricks in super structure plinth level upto all floor level in cement mortar 1:4 (one cement : four sand) upto all floor level including curing complete and carriage of material within all leads, lifts and other incidentals.

Random rubble masonry/polygonal rubble masonry (un-coursed/brought to courses) with hard stone of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement: six sand : twelve graded/crushed stone aggregate 20mm (twenty millimetre) nominal size at plinth level in cement mortar 1:6 (one cement : six sand) and curing complete including carriage of materials within all leads and lifts and other incidentals.

Squared rubble masonry coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1:6 (one cement : Six sand) including carriage of materials within all leads, lifts and other incidentials .

Stone filling tightly dry hand packed under floor as per specification or as per directed by the Engineer-In Charge with in all leads,lifts and other incidentals.

Providing and fixing Mild Steel grills of required pattern on wooden/steel frames of windows etc with mild steel flats square or round bars with round headed bolts and nuts or by screws welding plain grill including entire carriage of materials in all leads and lifts as per the direction of Engineer- in-Charge.

Providing and fixing 19mm (nineteen millimeters) thick commercial board water proof shutter for cup board including fixing with nickel plated piano hinges with screws etcectra complete including entire carriage of materials in all leads,lifts and heights as per the direction of the Engineer -in- charge.

Providing and fixing 250x16mm( two hundred fifty into sixteen millimetre) anodized aluminium sliding door bolts anodized colour and shade with bolts and nuts screws etc complete including carriage of material within all leads and lifts and other incidentials.size including carriage of materials within all leads and lifts and other incidentials .

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete including carriage of material within all leads, lifts and other incidentals.

200 x10mm ( two hundred into ten milimetre ) size

150 x10mm ( one hundred fifty into ten milimetre ) size

100 x10mm ( one hundred into ten milimetre ) size

Providing and fixing aluminium handles anodized transparent or dyed to required colour of shade with necessary screws etc. complete including carriage of material within all leads and lifts and other incidentals.

125 mm (one hundred twenty five millimetre) size

100 mm (one hundred millimetre) size

75 mm (seventy five millimetre) size

Providing and laying spartic ceremic tiles of 5.5mm(Five point five mililmetres) thick in flooring 300x300mm(Three hundred into three hundred milimetres size) treads and steps laid on a bed of 12mm(Twelve milimetres) thick cement mortar 1:3( One cement : Three sand) finished with flush pointing in white cement including carriage of materials with in all leads and lifts and other incidentals.

Providing and laying Duro stone vetrified tile 300x300x10mm ( three hundred into three hundred into ten milimetre ) in grey / coloured or of approved shade in flooring laid a bed on 12mm ( twelve milimetre ) thick cement mortar 1:3 ( one cement : three sand ) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of materials with in all leads and lifts and other incidentials .

Providing and laying Duro stone vetrified tiles 300x300mmx8mm ( three hundred into three hundred into eight milimetre ) in grey/coloured of required shade in skirting risers of steps and dados on 12mm (twelve milimetre) thick cement mortar1:3 (one cement: three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including carriage of materials with in all leads and lifts and other incidentals.

Providing and laying 20mm (twenty millimetre) thick acid proof tiles 300mmx300mm (three hundred millimetre into three hundred millimetre) thick in specified shade of superior quality in floors, treads of steps and landing laid on 12mm (twelve millimetre) thick bed of cement mortar 1:3 (one cement : three sand) jointing with cement slurry mixed with pigment to match the shade of tiles including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing 10mm (ten milimetre) thick antiskid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalent 600x600mmx10mm (six hundred milimetre into six hundred milimetre into ten milimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve milimetre) thick cement mortar 1:3(one cement: three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including entire carriage of material within all leads, lifts and other incidentals.

White glazed tiles 6 mm (six milimetre) thick in skirting risers of steps and dado 12 mm (twelve milimetre) thick cement mortar 1:3 (one cement :three sand) and jointed with cement slurry including carriage of materials with in all leads and lifts and other incidentals.

25mm (twenty five millimeters ) thick cement concrete flooring 1:2:4 (one cement : two sand : four graded crushed stone aggregate ) 20mm (twenty millimeters) nominal size laid in one layer finshed with a floating coat of neat cement curing complete including entire carriage of materials in all leads and lifts as per the direction of Engineer-in Charge.

Providing and fixing 0.60mm (zero point sixty milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified poliyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to black coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six milimetre) with prepainted G.I limpet and bitumen washers complete with all accesories as required as per direction of Engineer-in-charge with in all leads and lifts and other incidentals.

Providing and fixing ridges or hips overall 60 cm (sixty centimetre with 0.60mm (zero decimal six zero millimetre ) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) micron over 5 (five) micron primer coating to black coat of polyster of 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) diametre with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction and entire satisfaction of the Engineer-in-charge with in all leads and lifts and other incidentals.

Providing and fixing 100mm ( one hundred milimetre) dia pipes on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sq. mtr. ( four point five kilogramme per square metre ) including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 100mm (one hundred millimeter) diameter mild steel holder bat clamps of approved design to cast iron or sand cast iron pipe PVC pipe embedded in end including cement concrete block 10X10X10cm (ten into ten into ten centimeter) of 1:2:4 (one cement : two sand : four graded crushed stone aggregrate ) 20mm (twenty millimeter) nominal size and cost of cutting holes and making good the walls etc. including entire carriage carriage of material in all leads and lifts as per the direction of Engineer-in-Charge.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material within all leads, lifts and other incidentals.

PVC plain bend 150mm ( one hundred fifty milimetre) dia

PVC shoe 150mm ( one hundred fifty milimetre) dia

Providing and fixing mild steel BP sheet 1.66mm to 2mm (one point six six millimetre to two millimetre) thick in eaves board, facia, soffits, ceiling including cutting, fixing and welding to to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid for separately) including carriage of material within all leads, lifts and other incidentals.

Providing and fixing 0.63mm(Zero point sixty three millimeter) thick G.I. sheet 15cm (Fifteen centimeter) wide 45cm(Forty five centimeters) over all semicircular plain G.I Sheet gutter with iron brackets 40x3 mm (Forty into three millimeter) size bolts and nuts and washers etc. including making necessary connection with rain water pipe complete including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge.

Steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint upto any height including entire carriage of materials in all leads and lifts as per the direction of Engineer-in- Charge.

In gratings framed guard bars, ladders, railling, brackets and similar works

In trusses and trussed purlins in building complete.

Providing and fixing 75 mm x 60mm (seventy five milimetre into sixty milimetre) rounded hand rails in straight length complete in 2nd (second) class indian teak wood including entire carriage of materials in all leads and lifts as per the direction of Engineer-in- Charge.

Providing and fixing angle iron door,window,clerestory window frame manufactured from mild steel angle iron section of 50X50X6mm (fifty into fifty into six millimetre,thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50X25 mm (fifty into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock observer as specified and applying a coat of approved steel primer after preteatment of the surface including entire carriage of materials in all leads and lifts as per the direction of Engineer-in- Charge.

Providing and fixing 40mm (forty milimetre) thick including black enamelled mild steel butt hinges flush door shutters core of block board construction with frame of first class hard wood and well matched first class indian teak ply veneering with vertical grains or cross band and face vaneers on one face and commercial ply veneering with vertical grains cross band on other face of shutters.

Providing and fixing iron cup board frames manufactured from angle iron section 25x25x5mm (twenty five into twenty five into five milimetres ) thickness including hinges jamb lock,jamb beed and if required angle threshold a of mild steel angles 25x25mm ( Twenty five into twenty five milimetres ) welded or ridgly fixed by mechanical means lugs with split and tail each jamb including stell but hinges 2.5mm ( Two point five milimetres ) with a provision locking arrangement and shock observer as specified and applying a coat of approved steel primer after pretreatment of the surface as directed by the Engineer-in-Charge including carriage complete in all floor level as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals .

Providing and fixing steel glazed doors,windows and ventilators of standerd rolled steel sections standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (sixteen into three point one five milimetre) lugs 10 cm (ten centimetre) long embedded in cement concrete blocks 15cmx10cmx10cm (fifteen centimetre into ten centimetre into ten centimetre) size of 1:3:6(one cement: three sand: six graded stone aggregate 20mm (twenty milimetre) nominal size or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty of approved make complete including applying a priming coat of red lead paint including entire carriage of materials in all leads and lifts as per the direction of Engineer-in- Charge.

Fixed steel windows

Side hung windows

Top hung ventilators

Providing and fixing steel wire guage shutter in Z- section using galvainsed mild steel wire gauge of IS gauge desination 85G with wire of dia 0.56mm (zero point fifty six milimetre) for doors, windows and clearestory windows including metal beading of approved quality and shape section with necessary steel screws inluding applying a priming coat of red lead paint complete as per approved specification / design including entire carriage of materials in all leads and lifts as per the direction of Engineer-in- Charge.

Providing and fixing mild steel round holding down or anchor bolts with nuts and washer plates complete including all leads, lifts and carriage of materials as per entire satisfaction of Engineer-in-charge.

Painting two costs (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foregin matters with enamel paint other than white including carriage of material within all leads, lifts and other incidentals.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting with ready mixed paint brushing wood primer pink including carriage of material within all leads, lifts and other incidentals.

Painting two coats (excluding priming coat) on new wood and wood based surfaces, with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter, sand papering and stopping with enamel paint other than white including carriage of material within all leads and lifts and other incidentals.

6mm (six millimeter) cement plaster to ceiling /slopping surface in cement mortar 1:3 (one cement : three sand) in all floors level complete or as directed by the Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals .

15mm (fifteen millimeters) thick cement plaster in single coat on rough side of brick concrete / stone walls for interior plastering upto all floor level including arrises internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty millimeters) in girth and finished even and smooth in cement mortar 1:6 ( One cement : six sand) and curing complete including entire carriage of material in all leads and lifts as per of the direction Engineer- in- Charge.

15mm (Fifteen millimeters) thick cement plaster in single coat on fair side of brick concrete/ stone walls for interior plastering upto all floor level including arrises internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty millimeters) in girth and finished even and smooth in cement mortar 1:6 ( One cement : six sand) and curing complete including entire carriage of material in all leads and lifts as per of the direction Engineer- in- Charge.

15mm (fifteen millimeters) thick cement plaster in single coat on rough side of brick concrete/stone walls for interior plastering upto all floor level including arrises internal rounded angles, chamfers and / or rounded angles not exceeding 80mm (Eighty millimeters) in girth and finished even and smooth in cement mortar 1:3 ( One cement : three sand) and curing complete including entire carriage of material in all leads and lifts as per of the direction Engineer- in- Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equivalent on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete including entire carriage of material in all leads and lifts as per of the direction Engineer- in- Charge.

Wall painting (two coats) with plastic emulsion paint of approved brand and manufacture on undacorated wall surfaces to give an even shade including throughly brushing the surface free from mortar dropings and other foreign matter and sand papered smooth including applying a putty required for making the surface including entire carriage of material in all leads and lifts as per of the direction Engineer- in- Charge.

Distempering two coats with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surface to give an even shade over and including a priming coat distemper primer of approved brand and manufracture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth complete including entire carriage of materials in all leads and lifts as per the direction of Engineer -in-Charge.

White washing with lime on decorated wall surfaces (two coats)to give an even shade including thoroughly brooming the surface to remove all dirt dust mortar dirt and other foregien matter including entire carriage of materials in all leads and lifts as per the direction of Engineer -in-Charge.

Provding plinth protection 50mm (Fifty millimeters) thick in cement concrete 1:3:6(One cement:three sand:Six graded/crushed stone aggregate)20mm(Twenty millimeters) nominal size including finishing the top surface complete including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Provding under layer for plinth protection of 75mm (Seventy five millimeters) thick(unconsolidated )bed dry brick/aggregate 40mm(Forty millimeters) nominal size well rammed and consolidated and grouted with fine sand including preparation of ground complete including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Constructing course rubble hammer dressed U-Shape open surface drain with side wall 15x22cm (fifteen into twenty two centimetre) in cement mortar 1:6 (one cement : six sand) and inside plastering with cement plaster 1:3 (one cement : three sand) including earth work and laying 10cm (ten centimetre) thick cement concrete 1:5:10 (one cement : five sand : ten graded crushed stone aggregate 40mm (forty millimetre) nominal size) and 7.5cm (seven point five centimetre) cement concrete 1:2:4 (one cement : two sand : four graded crushed stone aggregate twenty millimetre) nominal size) and finished with a floating coat of neat cement complete as per standard drawing/design including carriage of material within all leads, lifts and other incidentals.

WATER SUPPLY AND SANITARY INSTALLATION Providing and fixing 20mm ( twenty millimeter nominal size) to wall, ceiling and floor galvanized mild steel tubes (medium grade) tube fitting and clamps including making good the walls, ceiling and floor complete in all respect including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing 15mm (fifteen millimeter nominal size) to wall, ceiling and floor galvanized mild steel tubes (medium grade) tube fitting and clamps including making good the walls, ceiling and floor complete in all respect including carriage of materials within all leads and lifts and other incidentials.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm (twenty millimetre) to 40mm (forty millimetre) nominal bore by providing and fixing tee including cutting and threading the pipes complete including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing vitreous Orissa Pattern china wash down, water closet squatting pan (Indian type W.C. pan) size 580mm (five hundred eighty milimetre) (earth work, bed concrete, foot rest and trap to be measured and paid for separately) including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Providing and fixing 110mm ( one hundred ten milimetre ) dia PVC 'P' or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement : one sand) (Seat and cover to be measured and paid for separately) (i) Ordinary closet including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Providing and fixing G.I. inlet connection for flush pipe with W.C pan including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing Solid type white plastic seat and cover for wash down water closet with C.P. brass hinges and rubber buffers including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing white vitreous china flat bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for seprately Flate back type of size 430mmx260mm x350mm (four hundred thirty milimetre into two hundred sixty milimetre into three hundred fifty milimetre) including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing 15mm (fiteen millimetre) nominal bore chromium plated brass flush pipes/ spreaders for urinal with fitting such as unions, clamps, etcetra (all in chromium plated brass ) including cutting holes and making good the same including carriage of material within all leads, lifts and other incidentals.

Providing and fixing vitreous China wash basin with single hole for pillar tap with cast iron or mild steel brackets painted white including cutting holes and making good the same but excluding fittings circular 460mm ( four hundred sixty milimetre) dia (countertop) including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Providing and fixing viterous China 600mmx450mmx250mm (six hundred milimetre into four hundred fifty milimetre into two hundred fifty milimetre) labouratory sink with cast iron or mild steel brackets painted white including cutting holes in walls and making good the same but excluding fitting including entire carriage of materials in all leads and lifts as per the diretion of Engineer- in-Charge.

Providing and fixing 32mm (thirty two milimetre) dia rubber plug for sink/wash basin including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing 32mm (thirty two milimetre) dia chromium plated brass waste for wash basin or sink including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing 32mm (thirty two milimetre) dia M.I. union for wash basin or sink including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing 100mm ( one hundred milimetre) sand cast iron griting for gully , floor or Nahni trap including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing 600x450mm (Six hundred into four hundred fifty millimeters) beveled edge mirror of superior glass mounted on 6mm (Six millimeters) thick A.C. sheet or plywood sheet and fixed to wooden plug chromium plated brass and washers complete including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing chromium plated brass towel rail complete with chromium plated brass bracket fixed to wooden plugs with chromium plated brass 600x 20mm ( six hundred into twenty milimetre) including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing division plate for urinals 600mm x 300mm (six hundred milimetre into three hundred milimetre) vitreous china including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing brass bib tap ( Superior or heavy type ) 15mm (fifteen millimetre) diametre including all leads, lifts and carriage of materials as per entire satisfaction of Engineer-in-charge.

Providing and fixing chromium plated brass bib tap with capastan head 15mm ( fifteen milimetre ) dia including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing chromium plated stop cocks 15mm ( fifteen milimetre ) dia including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing PVC connections pipe with brass unions 300/450mm (three hundred obluique four hundered fifty milimetre ) lenght 15mm ( Fifteen milimetres ) nominal bore complete upto all floor level including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing brass full way valve with wheel including carriage of materials within all leads and lifts and other incidentials.

15mm (fifteen milimetre ) nominal bore

20mm (twenty milimetre ) nominal bore

Providing and fixing 2000 (two thousand) litre net capacity PVC water storage tank of ISI : 12701 marked, inlet and outlet connection of galvanised iron, 15mm (fifteen millimetre) nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing 110mm x 75mm ( one hundred ten milimetre into seventy five milimetre ) PVC floor trap ISI marked self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etc. complete including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing PTMT jet spray of approved quality and colour with 1.5 mtr. ( one point five metre ) tube including carriage of materials within all leads and lifts and other incidentials.

Providing, laying (to level or slopes) and joining with stiff mixture of cement mortor in the proportion of 1:1 (one cement : one sand) salt glazed stone ware pipes grade "A" of the following internal diametres including testing of pipes and joints complete 100mm (one hundred milimetre) including carriage of materials within all leads and lifts and other incidentials.

Providing and laying cement concrete 1:4:8 (one cement : four sand : eight graded stone aggregate 40mm (forty milimetre) nominal size for surrounding or encasing stone ware pipes of the following internal diametre including concrete for bedding necessary form work and curing complete 100mm (one hundred milimetre) including carriage of materials within all leads and lifts and other incidentials.

Providing salt glazed stone ware fittings grade (A) bends of required degree (any radious of the following internal diametres 100mm (one hundred milimetre) including carriage of materials within all leads and lifts and other incidentials.

Providing salt glazed stone ware fittings grade (A) Single junction for required angle of 100mm (one hundred milimetre) diametres including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing stone ware gully trap grade 'A' complete with cast iron Grating, brick masonary chamber in cement mortar 1:5 (one cement : five sand) and water tight cast iron Cover with frame of 300mmx300mm (three hundred milimetre into three hundred milimetre) size (inside) the weight of cover to be not less than 4.53 kg (four point fifty three kilograme) and frame to be not less than 2.72 kg. (two point seventy two kilograme) round mouth traps 100mmx100mm (one hundred milimetre into one hundred milimetre) size P or S type including carriage of materials within all leads and lifts and other incidentials.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts and other incidentials.

110mm ( one hundred ten milimetre ) dia.

75mm ( seventy five milimetre ) dia

Providing and fixing PVC single equal branch plain ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts and other incidentials.

110mm ( one hundred ten milimetre ) dia.

75mm ( seventy five milimetre ) dia

Providing and fixing PVC collars ISI marked complete including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts and other incidentials.

110mm ( one hundred ten milimetre ) dia.

75mm ( seventy five milimetre ) dia

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts and other incidentials.

110mm ( one hundred ten milimetre ) dia.

75mm ( seventy five milimetre ) dia

Constructing manhole with reinforcement cement concrete top slab in 1:2:4 mix in one cement : two sand : four crushed stone aggregate 20mm (twenty millimetre) size, foundation concrete 1:4:8 (One cement : four sand : eight crushed stone aggregate 40mm (forty millimetre) nominal size with inside plastering 15mm (fifteen millimetre) thick in cement mortar 1:3 (one cement : three sand) finished with afloating coat of neat cement and making channnels in cement concrete 1:2:4 mix (one cement : two sand ; four crushed stone aggregate 20mm (twenty millimetre) nominal size) finished smooth complete including curing and testing, inside size 800mmx800mm (eight hundred millimetre into eight hundred millimetre) size and 500mm (five hundred millimetre) deep with frame ) light duty single seat pattern-I) 455mmx610mm (four hundred fifty five millimetre into six hundred ten millimetre) internal dimensions having total weight of cover and frame to be not less than 38 kg. (thirty eight kilogramme) (weight of cover 23kg (twenty three kilogramme) and weight of frame 15 kg. (fifteen kilogramme) with 200mm (two hundred millimetre) thick walls of second class common burnt clay building bricks in cement mortar 1:3 (one cement : three sand) including entire carriage of material within all leads, lifts and other incidentals.

Construction chamber 300mm x 300mm x 500mm (three hundred milimetre into three hundred milimetre into five hundred milimetre) inside size for stop cock with cast iron surface box 100mm x 100mm x 75mm (one hundred milimetre into one hundred milimetre into seventy five milimetre)inside size with hinged cover fixed in cement concrete slab 1:2:4 ( one cement: two sand: four graded stone aggregate 20mm (twenty millimetre) (twenty milimetre) nominal size ) 75mm (seventy five milimetre) thick foundation concrete 1:5:10 ( one cement:five sand:ten graded stone aggregate 40mm(forty milimetre) nominal size and insideplastering with cement mortar 1:3( One cement: three sand)finished with a floating coat of neat cement including curing complete with 100mm (one hundred milimetre) thick walls of brick masonry in cement mortar 1:5 ( One cement:fivesand )including all leads, lifts and carriage of materials as per entire satisfaction of Engineer-in-charge.

Supplying and fixing cast iron Cover 300mm x 300mm (three hundred milimetre into three hundred milimetre) with frame for gully trap (standard pattern) the weight of cover not less than 4.53kg (four point fifty three Kilogramme) including entire carriage of materials in all leads and lifts as per the direction of Engineer-in-Charge.

Construction chamber 600mm x 600mm x 750mm (six hundred milimetre into six hundred milimetre into seven hundred fifty milimetre) inside for fire hydrants with cast iron surface box 350mmx550mm (three hundred fifty milimetre into five hundred fifty milimetre) top and 165mm (one hundred sixty five milimetre) deep (inside) with chained lid and RCC top slab 1:2:4 (one cement : two sand : four graded stone aggregate 20mm (twenty milimetre) nominal size 100mm (one hundred milimetre) thick foundation concrete 1:5:10 (one cement : five sand : ten graded stone aggregate 40mm (forty milimetre) nominal size and inside plastering with cement mortar 1:3 (one cement : three sand) finished with a floating coat of neat cement including curing complete with 200mm (two hundred milimetre) thick walls of brick masonry in cement mortar 1:5: (one cement : five sand) including entire carriage of material within all leads, lifts and other incidentals.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of materials within all leads and lifts and other incidentials.

110mm ( one hundred ten milimetre ) dia.

75mm ( seventy five milimetre ) dia

Providing and fixing PVC double equal branch with oval acess door, incerstion rubber washer 3mm thick bolts and nuts ISI marked complete i/c fixing with approved adhesive etc. complete 110mm ( one hundred ten milimetre ) dia including carriage of materials within all leads and lifts and other incidentials as per the direction of Engineer-in-charge.

Supplying cast iron cover with out frame for man holes for frame of internal diamensions 455mmx610mm (four hundred fifty five milimetre into six hundred ten milimetre) rectangular cast iron Cover (light duty) single seat pattern (i) the weight of cover to be not less than 23 kg (twenty three kilogramme) including carriage of materials within all leads and lifts and other incidentials as per the direction of Engineer-in-charge.

Kumar Associates