Construction Of New R&B Division & Sub Division Office At Ahwa, Dist: Dang.

No figures

1 Excavation for foundation upto 1.5 m depth including 1091.00 Cumt 125.86

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter

lead.(A) Loose or soft soil

2 Excavation for foundation for depth from 1.5 m to 3.0 618.00 Cumt 309.04

m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto

Meter lead. (D) Soft rock not requiring Blasting

3 Filling in foundation and plinth with sand in layers of 106.00 Cumt 489.28

20 cm. Thickness including watering ramming and

consolidating etc. comp.

4 Filling available excavated Earth (Excluding Rock) in 1048.00 Cumt 137.47

trench plinth side of foundation . in layer not excluding

20 cm in depth consolidation each deposited layer by

ramming and watering etc. complete

soil in layer of 20 cm in thickness including ramming

watering and consolidating etc. complete

6 Applying general insecticide pest control treatment to 497.00 Sqmt 54.04

floors, cupboards etc including labour materials etc.

complete. Using Imidacloprid 30.5 SCas Per IS

part -II( (0.075% concentration by mass) is

recommended 10.5ml chemical diluted with 5 liters of

water application 0.5 litre chemical /Sqm of surface is

recommended as per I.S.

7 Providing and laying controlled cement concrete 189.63 Cumt 4048.90

M.150 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations and plinth pcc

8 Providing and laying controlled cement concrete 300.50 Cumt 5016.67

M.250 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (A) Foundations, footings, and Mass

concrete. footing

9 Providing and laying controlled cement concrete M- 27.00 Cumt 8443.60

250 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in (d) columns Up to Plinth

10 Providing and laying cement concrete 1:3:6 (1-Cement 28.00 Cumt 3106.67

: 3- coarse sand : 6- machine cut stone aggregates

mm nominal size) and curing complete excluding cost

of formwork in (A) Foundation and Plinth

11 Providing and laying controlled cement concrete M- 54.70 Cumt 8362.80

200 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and

struts G.FLOOR

12 Providing and laying controlled cement concrete M- 26.00 Cumt 8362.80

200 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and

struts F.FLOOR

13 Providing and laying controlled cement concrete M- 26.00 Cumt 8405.22

200 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and

struts 2nd.FLOOR

14 Providing and laying controlled cement concrete M- 12.00 Cumt 8446.63

200 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Columns, pillars posts and

struts 3rd.FLOOR

15 Providing and laying controlled cement concrete M- 96.50 Cumt 7058.89

250 and curing complete including the cost of form

work but excluding the cost of reinforcement for

reinforced concrete work in Ground & Plinth BEAMS

16 Providing and laying controlled cement concrete 77.00 Cumt 5427.74

M.150 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Plinth Slabs

17 Providing and laying controlled cement concrete 69.50 Cumt 6482.18

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Ground floor Beams,

18 Providing and laying controlled cement concrete 66.00 Cumt 6482.18

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) First floor Beams,

19 Providing and laying controlled cement concrete 66.00 Cumt 6523.59

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Second floor Beams,

20 Providing and laying controlled cement concrete 6.00 Cumt 6565.00

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Third floor Beams,

21 Providing and laying controlled cement concrete M- 8.00 Cumt 6432.69

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Chhajja for Ground floor

22 Providing and laying controlled cement concrete M- 5.00 Cumt 6432.69

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Chhajja for F floor

23 Providing and laying controlled cement concrete M- 5.00 Cumt 6475.11

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Chhajja for S floor

24 Providing and laying controlled cement concrete M- 1.00 Cumt 6516.52

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Chhajja for T floor

25 Providing and laying controlled cement concrete M- 1.50 Cumt 8972.84

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Lintal for Ground floor

26 Providing and laying controlled cement concrete M- 3.00 Cumt 8972.84

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Lintal for F floor

27 Providing and laying controlled cement concrete M- 3.00 Cumt 9015.26

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Lintal for S floor

28 Providing and laying controlled cement concrete M- 0.50 Cumt 9056.68

200 and curing etc. complete including the cost of form

work and reinforcement for reinforced concrete work

in (c) Lintal for T floor

29 Providing and laying controlled cement concrete 75.00 Cumt 7947.69

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Ground floor Slab

30 Providing and laying controlled cement concrete 62.00 Cumt 7947.69

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) First floor Slab

31 Providing and laying controlled cement concrete 62.00 Cumt 7989.10

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Second floor Slab

32 Providing and laying controlled cement concrete 7.00 Cumt 8031.52

M.200 and curing complete including the cost of

formwork and excluding reinforcement for reinforced

concrete work in (C) Third floor Slab

33 Providing and laying controlled cement concrete M- 5.00 Cumt 6166.05

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in RCC Vertical and horizontal wall for GF

34 Providing and laying controlled cement concrete M- 7.00 Cumt 5961.02

250 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in RCC Vertical and horizontal wall for Up to

35 Providing and laying controlled cement concrete M- 16.50 Cumt 6166.05

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in RCC Vertical and horizontal wall for FF

36 Providing and laying controlled cement concrete M- 5.00 Cumt 6207.46

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in RCC Vertical and horizontal wall for SF

37 Providing and laying controlled cement concrete M- 2.00 Cumt 6248.87

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in RCC Vertical and horizontal wall for TF

38 Providing and laying controlled cement concrete M- 7.00 Cumt 7381.08

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in (E) Stair case up to floor two level for

Ground Floor to first floor

39 Providing and laying controlled cement concrete M- 5.00 Cumt 7381.08

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in (E) Stair case up to floor two level for First

to Second Floor

40 Providing and laying controlled cement concrete M- 5.00 Cumt 7422.49

200 and curing etc. complete including the cost of form

work and excluding the cost of reinforcement etc.

complete in (E) Stair case up to floor two level for

Second to Third Floor

41 Providing and fixing 90 cm high Stainless steel railing 57.00 Rmt 3719.83

made from anticorrocive 316 grade S S pipe of 50 mm

dia (16Gauge) as hand rail with S S 316 grade Baluster

of 38 mm dia (16Gauge) as a vertical support fixed in

RCC slab at 1.2m c/c including three horizontal S S

pipes of 25 mm dia (16Gauge) at eqal distance fixed by

18.75 mm dia (16Gauge) S S pipe with baluster

including accessories as per detailed drawing as

directed etc. complete.

42 Providing and fixing Stainless Steel Hand Railing made 36.00 Rmt 1969.50

from anticorrocive 316 grade S S pipe of 50 mm dia

(16 Gauge) as hand rail with S S 316 grade Baluster of

40 mm dia (16 Gauge) as a vertical support fixed in

RCC member at 1.2m c/c S S pipe with baluster

including accessories as per detailed drawing as

directed etc. complete.

43 Providing IS Mark TMT FE 500D bar reinforcement for 126754.00 Kg 77.77

RCC work including bending & placing in position

complete up to All floor Level

44 Brick work using common burnt clay building bricks 125.00 Cumt 4279.98

having crushing strength not less than 35 Kg./Sq.m. in

foundation and plinth in cement mortar 1:6 (1

cement:6 fine sand) (b) Conventional.

45 Brick work using common burnt clay building bricks 156.00 Cumt 4575.57

having crushing strength not less than 35 Kg./ Sqm. in

cement mortar 1:6 ( 1 cement : 6 Fine sand ) in super

structure above plinth level upto floor two level ( for

G.F ) Conventional

46 Brick work using common burnt clay building bricks 77.00 Cumt 4575.57

having crushing strength not less than 35 Kg/Sq.cm. in

super structure in cement mortar 1:6 (1cement : 6 fine

sand) {First FLoor}

47 Brick work using common burnt clay building bricks 73.00 Cumt 4618.66

having crushing strength not less than 35 Kg/Sq.cm. in

super structure in cement mortar 1:6 (1cement : 6 fine

sand) {SF FLoor}

48 Brick work using common burnt clay building bricks 42.00 Cumt 4661.75

having crushing strength not less than 35 Kg/Sq.cm. in

super structure in cement mortar 1:6 (1cement : 6 fine

sand) {TF FLoor}

49 Half brick masonry in common brunt clay building 142.00 Sqmt 697.93

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional for G

50 Half brick masonry in common brunt clay building 376.00 Sqmt 697.93

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional for

51 Half brick masonry in common brunt clay building 377.00 Sqmt 704.33

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional for

2nd floor.

52 Half brick masonry in common brunt clay building 15.00 Sqmt 710.74

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1-Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional for

3rd floor.

53 Providing 20 mm thick double coat mala cement 641.50 Sqmt 290.72

plaster on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster

in cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2

(1 Cement : 2 Coarse sand) finished with trovel

including scaffolding curing etc. complete.For GF

54 Providing 20mm thick cement plaster in single coat on 1404.00 Sqmt 290.72

single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand)For FF

55 Providing 20mm thick cement plaster in single coat on 1405.00 Sqmt 319.44

single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand)For SF

56 Providing 20mm thick cement plaster in single coat on 257.00 Sqmt 348.17

single or half brick walls for interior plastering upto

floor two level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand)For TF

57 Providing 10 mm. Thick Mala plaster in single coat for 821.50 Sqmt 198.57

plastering on ceiling and soffits of stairs and finished

in : (I) Cement mortar 1:4 (1 cement : 4 sand) with

Mala finished of neat cement slurry etc.

complete.Ground Floor

58 Providing 10 mm. Thick Mala plaster in single coat for 534.00 Sqmt 198.57

plastering on ceiling and soffits of stairs and finished

in : (I) Cement mortar 1:4 (1 cement : 4 sand) with

Mala finished of neat cement slurry etc. complete.F

59 Providing 10 mm. Thick Mala plaster in single coat for 533.00 Sqmt 223.72

plastering on ceiling and soffits of stairs and finished

in : (I) Cement mortar 1:4 (1 cement : 4 sand) with

Mala finished of neat cement slurry etc. complete.S

60 Providing 10 mm. Thick Mala plaster in single coat for 43.00 Sqmt 248.86

plastering on ceiling and soffits of stairs and finished

in : (I) Cement mortar 1:4 (1 cement : 4 sand) with

Mala finished of neat cement slurry etc. complete.T

61 Providing and laying synthetic Granular Texture 2757.00 Sqmt 687.41

plaster of average 2-3 mm thickness on a base of

smooth mala plaster having final coat incorporating

fine filaments made up of polymers and aggregating

natural stone powder as tvaried drection,colour and

shade for all floor approved by architect office.

62 Providing 20 mm thick double coat mala cement 2895.00 Sqm 348.17

plaster on Exterior brick / concrete work for

plastering comprising of base coat of 12 mm thick

cement plaster in cement mortar (1Cement : 4 coarse

sand) in roughfinishing and 8 mm thick top coat of

cement mortar 1:2(1Cement : 2 Coarse sand) finished

with trovel including scaffolding curing etc. complete.

63 Providing throating or plaster drip and moulding to 251.00 Rmt 45.33

R.C.C. Chhajja.

64 Providing and finishing POP PUMMING Plaster of 5043.00 Sqmt 217.35

Paris Punning with necessary groove over plastered

wall surface to be finished in line and plumb with

smooth surface ready to receive paint base.(1)12 mm

Average Thickness (2)19mm Average Thickness

including on Punning applying to give an even shade

including thoroughly brushing the surface free from

mortar droppings and other foreign matter and sand

papered smooth. For all floor

65 Wall painting (three coats) with plastic emulsion paint 3610.50 Sqmt 128.91

of approved brand and manufacture on undecorated

wall surface to give an even shade to colour including

throughly brushing the surface free from mortar

droppings and other foreign matter and sand papered

66 Painting (two coats) with plastic emulsion paint of 1931.50 Sqmt 90.64

approved brand and manufacture on undecorated

ceiling surface to give an even shade to colour

including throughly brushing the surface free from

mortar droppings and other foreign matter and sand

papered smooth.

67 Wall Painting (Two coats) with weather proof 100 % 2872.00 Sqmt 122.14

acraylic emulsion (Apex or equivalent type)Water

Repllent paint of approved brand and manufacture and

of required shade on exterior wall surface to give an

even shade over and including primery coat with

Alkaly resistance primer of approved brand after

thoroughly brushing surface to remove all dust and

remains of loose powdered material etc. copm. for all

68 Providing and laying controlled cement concrete M- 11.00 Cumt 8379.97

200 for RCC work and curing complete including the

cost of form work but excluding the cost of reinforced

concrete work in coping on Ground Floor

69 Providing and laying controlled cement concrete M- 3.50 Cumt 8379.97

200 for RCC work and curing complete including the

cost of form work but excluding the cost of reinforced

concrete work in coping on First Floor

70 Providing and laying controlled cement concrete M- 3.00 Cumt 8422.39

200 for RCC work and curing complete including the

cost of form work but excluding the cost of reinforced

concrete work in coping on S Floor

71 Providing and laying controlled cement concrete M- 5.00 Cumt 8463.80

200 for RCC work and curing complete including the

cost of form work but excluding the cost of reinforced

concrete work in coping on T Floor

72 Providing & fixing in position standard extruded 133.00 Sqmt 3796.59

Aluminum Four track (4 shutter) with Fix Glass above

an top Standard Extruded Colour Anodied Alluminium

Section Equivalent to Jindal Series E (30mm) Section

Numbered: Frame -Bottom with Weep Holes -20737,

Frame Top & Side-20738 ,Shutter Top & Bottom

20993, Shutter Inter Lock -20550 ,Shutter Side

(handle) -20549 With 5mm thick Transparent Tinted

Float Glass With EPDM Rubber Gasket, Air Lock Stirip

and Finishing , Joint With Section Sealant, With Power

Coated Standard Alluminium Fitting.with as per

window size including all required materials labours

and equipments as per detailed drwg. as directed.

73 Providing & fixing in position standard extruded 22.00 Sqmt 3843.05

Aluminum Three track (3 shutter) with Fix Glass

above an top Standard Extruded Colour Anodied

Alluminium Section Equivalent to Jindal Series E

(30mm) Section Numbered: Frame -Bottom with Weep

Holes -20737, Frame Top & Side-20738 ,Shutter Top &

Bottom 20993, Shutter Inter Lock -20550 ,Shutter Side

(handle) -20549 With 5mm thick Transparent Tinted

Float Glass With EPDM Rubber Gasket, Air Lock Stirip

and Finishing , Joint With Section Sealant, With Power

Coated Standard Alluminium Fitting.with as per

window size including all required materials labours

and equipments as per detailed drwg. as directed.

74 Providing & Fixing in position standard extruded 8.00 Sqmt 3098.68

approved colour anodised Aluminum Ventilator with

outer frame 65.00 x 25.00 x 1.95 mm (of Jindal Section

No.4605,@ Wt 1.094 kg/Rmt ) with 3mm thick Bajari

figure adgesteble tinted louvers glass fixed to

alluminium strip blade including fixtures , fastenning

labours and equipments as per detailed drawing as

directed. For Ventilators

75 Providing and fixing anodized aluminium door frame 9.00 Sqmt 4648.02

equivalent to Jindal door section No. 19552, weighing

not less than 1.10 kg per metre, with wooden inserts

for durable grips at door hinges and hardware,

complete in all respects; and providing and fixing

mm thick solid core wooden flush double shutters with

Side FIX Glass 5 mm thick conforming to IS:2202 and

ISI approved manufacturer, finished with 1 mm thick

laminates on both sides of each shutter, 6 mm thick

S.S. 316 handles on both sides, S.S. fixtures and locking

arrangement of standard make (Kich or equivalent),

fixed with 150 mm high S.S. hinges and floor spring,

including all fittings, fixtures, samples and shade as

approved by the Architect, complete.

76 Providing and fixing anodized aluminium door frame 96.00 Sqmt 6377.14

equivalent to Jindal door section No. 19552, weighing

not less than 1.10 kg per metre, with wooden inserts

for durable grips at door hinges and hardware,

complete in all respects; and providing and fixing

mm thick solid core wooden flush Single shutters

conforming to IS:2202 and ISI approved manufacturer,

finished with 1 mm thick laminates on both sides of

each shutter, 6 mm thick S.S. 316 handles on both

sides, S.S. fixtures and locking arrangement of

standard make (Kich or equivalent), fixed with

mm high S.S. hinges and floor spring, including all

fittings, fixtures, samples and shade as approved by

the Architect, complete.

77 Providing and fixing anodized aluminium door frame 8.00 Sqmt 5387.34

equivalent to Jindal door section No. 19552, weighing

not less than 1.10 kg per metre, with wooden inserts

for durable grips at door hinges and hardware,

complete in all respects; and providing and fixing

mm thick solid core wooden flush Double shutters

conforming to IS:2202 and ISI approved manufacturer,

finished with 1 mm thick laminates on both sides of

each shutter, 6 mm thick S.S. 316 handles on both

sides, S.S. fixtures and locking arrangement of

standard make (Kich or equivalent), fixed with

mm high S.S. hinges and floor spring, including all

fittings, fixtures, samples and shade as approved by

the Architect, complete.

78 Providing and fixing anodized aluminium door frame 5.00 Sqmt 5177.26

equivalent to Jindal door section No. 19552, weighing

not less than 1.10 kg per metre, with wooden inserts

for durable grips at door hinges and hardware,

complete in all respects; and providing and fixing

mm thick solid core wooden flush double shutters with

Above FIX Glass 5 mm thick conforming to IS:2202

and ISI approved manufacturer, finished with 1 mm

thick laminates on both sides of each shutter, 6 mm

thick S.S. 316 handles on both sides, S.S. fixtures and

locking arrangement of standard make (Kich or

equivalent), fixed with 150 mm high S.S. hinges and

floor spring, including all fittings, fixtures, samples and

shade as approved by the Architect, complete.

79 P & L 60x60 cm' Double Charged vitrified Tiles 10 mm 387.00 Sqmt 1406.93

thick tile flooring over 20mm (Average) thick base of

cement mortar 1:6 (1-cement : 6-coarse sand) or L.M.

1.1.5 laid over and jointed with grey cement slurry

including rubbing and polishing etc

80 Providing and laying Vitrified tiles 8 to 10 mm thick , 70.00 Sqmt 1531.82

36'' x 36'' in flooring treads of steps and landing laid

on a bed of 12mm thick cement mortar 1:3 (1-cement :

3-coarse sand ) finishing with flush pointing in white

81 P & L 60x60 cm' antiskid porcelene Tiles 10 mm thick 45.00 Sqmt 1756.39

tile flooring over 20mm (Average) thick base of

cement mortar 1:6 (1-cement : 6-coarse sand) or L.M.

1.1.5 laid over and jointed with grey cement slurry

including rubbing and polishing etc

82 Providing and laying antiskid Ceramic tiles 6mm thick 75.50 Sqmt 1017.30

in flooring treads of steps and landing laid on a bed of

12mm thick cement mortar 1:3 (1 cement : 3-coarse

sand ) finishing with flush pointing in white cement.

83 Providing and laying Ceramic tiles 6mm thick in 498.50 Sqmt 1091.96

skrting risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3-coarse sand) and jointed with

white cement slurry

84 P & L 60x60 cm' GVT Tiles 10 mm thick tile flooring 315.00 Sqmt 1431.17

over 20mm (Average) thick base of cement mortar 1:6

(1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and

jointed with grey cement slurry including rubbing and

polishing etc

85 Providing and fixing readymade full body vitrified tiles 118.00 Sqmt 1913.95

colour in staircase area, including 152 × 30 cm treads

nosing and self-embossed anti-skid strips, 150 × 15 cm

risers, 60 × 60 cm full body vitrified tiles in

landings/rest areas, and 10 cm high skirting of the

same material and colour, laid over prepared surface

using approved tile adhesive, maintaining proper line,

level and alignment, including cutting, edge finishing,

joint filling with matching grout, cleaning and all

incidental works, complete in all respects as directed

by the Engineer-in-Charge.

86 Providing and laying water proofing treatment with 453.00 Sqmt 779.70

broken chine mosaic flooring for terrace using 12 mm

to 20 mm broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to be

tempered to bring mortar creme out upto surface

using white cement including rounding off junctions

and extending them upto 15 cm along the wall,

clearing with water and oxalic acid etc. as directed.

87 Providing and laying cement concrete flooring 1:2:4 (1- 453.00 Sqmt 348.85

cement : 2-coarse sand : 4-graded stone aggregate

20mm nominal size) laid in one layer and finished

with a floating coat of neat cement. (B) 50mm thick.

88 Providing and laying Heavy Duty 10 to 12 mm thick 359.00 Sqmt 1522.47

Parking Vitrified tiles flooring of PAVIT or equivalent

make in required pattern, shape & design, laid on

mm. thick cement mortar 1:6 ( 1 cement : 6 coarse

sand) make with spacer joint of approved quality

cement grout of the make Bal Gold Star, cleaning,

washing & etc. complete. For Parking

89 Providing and fixing Granite 18 to 20 mm with full 214.50 Sqmt 1995.76

round edge and polished of approved quality in clading

on sill and around the doors/ windows/ ventilation

with 12 mm thick cement mortor CM (1:4) and fixing

with cement slurry & adhesive including moulding of

exposed edges as directed by engineering in charge

etc. complete.

90 Providinfg and fixing Safty grills of required pattern for 2904.00 Kg 125.85

windows/ Door using necessary M.S angle/ M.S pipe,

M.S flats and other structural steel at required spacing

including cutting, welding and fabriction etc. including

one coat of primer of approved quality and two coats

of oil painting as per detail drawing etc complete.

91 Providing Erecting and fixing Triple Layer Plastic Pure 10000.00 Litre 12.63

Antibacterial Water White Tank of required capacity

each with all necessary fittings and connection etc.

complete on terrace.

92 Providing laying and jointing in true line and level 60.00 Rmt 195.67

50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

93 Providing laying and jointing in true line and level 190.00 Rmt 148.12

40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

94 Providing laying and jointing in true line and level 330.00 Rmt 91.84

25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

95 Providing laying and jointing in true line and level 240.00 Rmt 72.65

15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold water

including fittings make PRINCE / SUPREME / ASTRAL

/ FINOLEX or equivalent as approved by Engineer In

Charge. Pipe shall be fixed on the wall with the help of

clamp at every two metre C/C or shall be concelled as

directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

96 Providing, laying and jointing in true line and level 160 50.00 Rmt 834.38

diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with

rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of the

size 160 mm diametre x 210 mm length x 196 mm

heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

97 Providing laying (to level or slopes) and jointing 372.00 Rmt 678.03

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with

collars and butt ends prepared for collar joints

including testing of joints complete.(D)

98 Providing, laying and jointing in true line and level 110 100.00 Rmt 899.49

diametre U.P.V.C (Type B) conforming to IS 13592-

1992 with one end plain and other end socketed with

rubber ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe

shall be jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of the

size 110 mm diametre x 149 mm length x 145 mm

heigh at every 2000 mm center to center or shall be

concealed in walls as directed including necessary

fittings such as bends, shoes etc. including testing of

pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

99 Providing, laying and jointing in true line and level 75 30.00 Rmt 779.72

mm dia. UPVC SWRType B pipe conforming to IS

13592-1992 with one end plain and other end

socketed with rubbering and fitting conforming to ISI

14735-1999 of approved make for drainage system

pipe line, pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall using of

PVC clamp at every 2000 mm c/c or shall be conceled

in walss as directed including necessary fittings such

as bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement

including cost of all materials.

100 Providing and fixing in PVC SWR cowel went 75mm 2.00 No 15.66

dia to pipes.(B) 75mm dia.

101 Providing and fixing in PVC SWR cowel went 110mm 10.00 No 28.79

dia to pipes.(B) 110mm dia.

102 Providing and fixing MS Z clamp on Wall or celling for 415.00 No 116.15

Pipe Fitting including all type necessary fittings and

accessory etc. completed as per directed engineer in

103 Providing and fixing PVC SWR Nahni trap IS 14735 for 30.00 No 613.92

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I

scread down or hinged grating including the cost of

cutting and making good the walls.

104 Providing and fixing Tankless Wall Hung WC with 10.00 No 33218.90

Sensor Flush, model ONS-WHT-10961BIUFSMTL or

Jaquar standard company, of size 380 x 625 x 385 mm,

complete with UF soft-close slim seat cover, hinges,

concealed flush system, suitable wall frame support

system ( Jaquar ), exposed part kit of concealed stop

cock & flush cock (model KUP-35083KPM or

equivalent), health faucet (model ALD-577 or

equivalent) with 8 mm dia, 1 meter long flexible tube,

wall hook and N.R.V. (backflow preventer), including

all required fittings, accessories, connection materials,

testing and installation complete as per

manufacturer’s specifications and as directed by the

Engineer-in-Charge.

105 Providing and fixing S3030102 Orissa Pan Cello 500 x 5.00 No 3764.25

400 mm CERA or equivalent premium quality awith

'P' or 'S' trap jointed with C.I. pipes in C.M. 1:1

complete for all Floor with all accessories etc.

complete. The BRAND should be as per given

specification or Equivalent or as per directed engineer

106 Providing and fixing stainless steel grab 22 cm x 60 cm 3.00 No 1492.78

for handicapped toilet

107 Providing and Fixing a set of wall mounted 38 mm dia 3.00 No 5090.40

U shaped horizontal stainless steel collapsible grab bar

, 38mm vertical stainless steel fixed grab rail of grade

SS 304 from round pipe supported and 75 mm dia

mm thick SS 304 base flange on wall including anchor

fasteners, nuts, accessories as per detailed drawing

etc. complete as directed by Architect or Engineer in

108 Providing and fixing Bib Cock (Straight Line Model) 25.00 No 2643.17

with Wall Flange (Range: Solo, Code: SOL-CHR-6047)

made of high quality brass with chromium plated

finish, complete with wall flange, nuts, washers and all

necessary fittings, including connection to water

supply line, complete as directed by the Engineer-in-

109 Providing and fixing Full Pedestal Wash basin for CNS- 5.00 No 6806.39

WHT-801 Jaquar brand or equivalent CNS-WHT-801

wall mounted Size: 560x415x200 size snow white with

C.I. or M.S. bracket including cutting holes and making

good the same including fixing Auxiliaries - Waste

coupling full thread, C.P. brass extension nipple 62 mm

long, S.S. flange water super connection pipe 60cm.

long and full thread waste coupling, etc.

complete.The BRAND should be as per given

specification or Equivalent or as per directed engineer

110 Providing and fixing 5 mm thick mirror of approved 12.00 No 993.54

quality and make size 600 x 450 mm with moulding

edge by using 4.0 mm thick hard board and fixing on

wall with C. P.brass studs etc. complete. For all floor

The BRAND should be as per given specification or

Equivalent or as per directed engineer incharge

111 Providing and fixing ball cock of approved. quality as 2.00 No 189.84

directed.(A) Copper Metal (ii) 50mm dia.

112 Providing and fixing Chrome plated Bib Cock with Wall 15.00 No 3049.19

Flange (Make: Opal Prime, Range: Opal Prime, Code:

OPP-CHR-15037PM) of approved quality, made of high

quality brass with chromium plated finish, including

wall flange, complete with all necessary fittings, joints,

nuts, washers and connection to the water supply line,

complete as directed by the Engineer-in-charge.

113 Providing and fixing Single Towel Rail 450 mm long 18.00 No 3165.34

(Range: Continental, Code: ACN-ABR-1111BSM) made

of high quality brass with approved finish, fixed to wall

with necessary screws, rawl plugs and fittings,

complete in all respect as directed by the Engineer-in-

114 Providing and fixing Pillar cock JAQUAR brand 18.00 No 1835.17

FLORENTINE CAT. NO. - 5011N with 15 mm dia with

C.P. brass extension nipple 62 mm long etc.

complete.The BRAND should be as per given

specification or Equivalent or as per directed engineer

115 Providing and fixing in position 300 mm high, 150 mm 100.00 No 707.00

wide English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

116 Providing and laying (two level or slopes) and jointing 70.00 Rmt 531.19

with stiff mixture of Cement Mortar in proportion 1:1,

Salt glazed stone ware pipes of pipes 150mm laying

lime concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-

Graded brick aggregates 40mm nominal size) bedding

for stoneware pipes of following internal diameters

with necessary formwork and curing complete.

117 Providing and fixing S.W. gully trap with C.I. grating 10.00 No 1246.92

brick masonry chamber and water tight C.I. cover with

frame of 300mm x 300mm size (inside) with standard

weight (i) Square mouth traps (B) 150mm x 100mm

size P or R type

118 Constructing brick masonry chamber for underground 12.00 No 3454.80

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal

dimensions with frame (R.C.C. top slabe with 1:2:4 mix

(1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete (i) Inside dimensions 455mmx

610mm and 450mm deep for single pipe line.

119 Constructing brick masonry chamber for underground 11.00 No 4258.97

C.I. Inspection C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg.

Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm

intenal dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3

finished smooth with a floating coat of neat cement on

walls and bed concrete etc. complete (i) Inside

dimensions 500mmx 700mm and 450mm deep for

single pipe line.

120 Extra over items for every additional depth of 0.1M. of 6.00 Each 242.39

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 455mm x 610mm size.

121 Extra over items for every additional depth of 0.1M. of 5.00 Each 264.86

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 500mm x 700mm size.

122 Providing and fixing MS Ladder of required pattern 250.00 Kg 126.76

with MS flats(30x3mm) or round or square bars

(12mm) at required spacing & with round headed

bolts and nuts or screws or welding including primer

coat of approved quality and two coats of oil paintas as

directed by engineer in charge

123 Providing and fixing in position 150 mm high, English 100.00 No 404.00

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools

& plants etc. complete.

124 Constructing drinking/Handwash Platform of 18 mm 7.00 Sqmt 8228.47

thick Polished Black Granite having 0.45m width and

0.60m height including 0.60m support at every 0.7m

c/c with cementing Materials / adhsives including

makeing necessary grooves in walls including Wash

Basin Snow White size 400x400x135mm including

Polyamide braided connection pipe 12mm dia, 450mm

length Wast coupling with ceramic Pop-up push type

(Full thread) 32mm Dia Cat. No. F8050351 with all

fitting inlet and outlet connection and all required

fitting accessories etc. with all labour material of

approved quality incl. full moulded round front edge

granite strip of one side polished and jointed with

grey cement slurry including rubbing and polishing

etc. complete for all floors

125 Providing and fixing Urinal of Jaquar URS-WHT- 9.00 Nos 6864.47

13261H Urinal With Spreader Hole And Fixing

Accessories, Size: 355x340x535 mm including

connection with trap , Auxiliaries Waste coupling full

thread and with integral longitudinal flush pipe with

Quarter turn flush valve Brass etc completed The

BRAND should be as per given specification or

Equivalent or as per directed engineer incharge

126 Providing and fixing polished 18 mm thick black 5.00 Sqmt 2897.69

granite with full round edge and double side polished

of approved quality in between urinal and fixing with

cement slurry & adhesive including moulding of both

exposed edges as directed by engineering in charge

etc. complete.

127 Charges for making holes from 50mm to 160 mm dia 40.00 No 858.50

in RCC wall, slabs or any other RCC members or Brick

work by diamond core cutting machine of HILTI or

equivalent including disposing the debris. For all floors

128 Providing and fixing coloured self adhesive PU-Tactile 54.00 Sqmt 4586.41

tile, ground surface indicators of Polyurethane) of size

300mm x 300mm for guiding/warning to the visually

visitors in the centre/side of the pedestrian/approach

pathway as per specification and guidelines complete

in all respect to the entire satisfaction of in charge.

129 Providing and fixing 150 mm wide, approved quality 544.00 Sqmt 368.65

chicken wire mesh at junction of brick work and RCC

work or two dissimilar surfaces, at all heights fixed by

nails, rowal plugs or tag by cement mortar 1:3 before

applying the plaster, including curing, scaffolding all

complete as directed.

130 Providing and fixing acrylic multilingual Braille (raised 36.00 Nos 1696.80

dots) DIRECTIONAL SIGNBOARDS of size 225 x

150mm designed as per accessibility standards and

having 3.5mm thick acrylic base plate with Upper Case

San Serif words made of white acrylic non glare cut out

letters of height 15mm raised not less than 0.8mm

above base plate and the equivalent word written in

Hindi with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above base

plate and having a non-glare acrylic cut arrow pointing

in the required direction. Each signboard to be fixed as

per manufacturers specifications on the wall at the

approved location and at a height of 1200mm from FFL

complete as per design / specifications and guidelines

as per the entire satisfaction of the Engineer-in-charge

131 Providing And filling with good quality sinder(steam 70.00 cumt 555.50

coal) as directed by engineer in charge in sunks in

layers of 15 cm thick,including watering,placing

,ramming well etc as directed, for all floor.

132 Providing and laying water proofing treatment by 93.00 sqmt 986.77

conventional method including cleaning the slab

surface by wire brush as directed including provding

first layer of C.M. 1:4 of 40 mm thickness mixed with

water proofing compound at rate prescribed by

manufacturer, including putting of brick bats of

average thickness 40 mm Well immerssed in water

laid uniformly on first layer of mortar including

applying cement slurry @ rate of 0.08 bag/sqm. on

fixed layer of brick bats including maintaining

necessary slope, in second layer 40 mm thick C.M 1:4

mixed with water proofing compound as directed,

including finishing smooth with cement slurry as

directed complete.

133 Providing & Fixing tactile layout plan of size 900mm x 1.00 Nos 33027.00

600mm as approved design, made of 3.0mm thick

acrylic non glare base plate and non glare cut out

symbols with Braille on which individual facility

points, like inquiry, reception, restrooms, medical

room / first aid, cafeteria or breakout area, lounge,

meeting room, conference room etc. present the

respective floors with pictograph wherever needed all

in tactile raised by minimum of 1.0mm to 2mm in

various colours to make it legible for seniors, partial

vision impaired etc. All the facility names should be in

Braille, along with English or Hindi. The entire block of

tactile signs should be mounted on wall for easy

reading. The map to be installed at specified locations

and installed at a height of 800mm from ground level

complete in all respect as per Harmonized guideline &

satisfaction of Engineer in charges.

134 Providing and fixing of acrylic, non-glare, tactile audio 1.00 Nos 43480.50

pictorial building layout as per the approved size,

design and make, having 3mm thick acrylic non glare

base plate of the approved colour and non-glare acrylic

cut out symbols raised 3mm above base plate and

Grade 2/ Grade 1 Braille to be integral with the sign

face and be raised 0.5mm above base plate. The map to

be installed at the specified location as per

accessibility standards, shall be oriented to the

position of the viewer and to be installed at a height of

800 mm from the finished ground/ floor level and

using the necessary hardware specified by the

manufacturer and to be installed up to the height of

800 mm from the finished ground/ floor level and

using the necessary hardware specified by the

manufacturer and to be installed complete as per

design/specifications and guidelines as per the entire

satisfaction of the the Engineer-in-charge

135 Providing & fixing Braile indicator of size 170 mm x 90.00 Rmt 820.12

35mm for handrails of the approved design and make

have braile dots raised 0.5 mm above base plate to be

installed at specific locations as per direction of

engineer in charge

136 Providing and fixing of conspectus tape 50mm width 90.00 Rmt 91.91

on of treads in staircase including cutting pasting etc.

As per harmonised guidelines complete in all respect

to the entire satisfaction of engineer in charge.

137 Providing and fixing POP false ceiling including all 367.00 sqmt 972.63

necessary framework, supports, and accessories. The

system consists of main channels, intermediate

channels, and perimeter channels fabricated from

suitable galvanized sections, with hangers (rods,

cleats, and fasteners) and connecting clips/screws for

proper alignment and stability. A wire gauge mesh of

0.71 mm thickness is fixed as required. The false

ceiling is finished with 9 mm thick POP (Plaster of

Paris) powder applied over the framework to achieve a

smooth and level surface. The work includes careful

measurement and execution as per site conditions,

including proper fixing of all channels, accessories, and

POP finishing, complete with labour charges, ensuring

a durable, as approved by the engineer-in-charge.

138 Providing & Fixing 114mm wide G.I. Sheets lovers 17.00 sqmt 5091.41

having weight not less than 490 Gm/m roll formed to

create 84mm wide louver snap fixed on special shaped

GI channel. Fix louvers & channels shall finished with

powder coating of 55 micron (1) 0.55mm thick

139 20mm thick sand faced cement plaster on walls upto 55.00 Sqmt 365.95

height 10 metres above ground level consisting of 12m

thick backing coat of C.M. 1:3 (1-cement : 3-sand) and

8mm thick finishing coat of C.M. 1:1 (1-cement : 1-

sand) etc. complete.

140 Providing and fixing C.I. Manhole cover 0.60 M. x 1.00 Nos 958.17

0.45M. size having weight not less than 35Kg.

141 Providing & erecting open well horizontal mono block 1.00 Nos 16483.20

pump set with cast iron body, complete for three phase

submersible motor having [H]For 5 H.P,3 phase open

well horizontal mono block pump set suitable for

LPM to 285 LPM @ 20 to 24 MTR head suitable for

65/80 mm dia delivery pipe

142 Supplying & erecting approvedmake 3 phase motor 1.00 Nos 19695.00

control cubicalpanel (Star-Delta) made from 16G.CRCA

sheet duty painted with epoxy powder painted inside

and outside with hinged doors and locking

arrangement, consisting suitable size of ON-OFF

isolator (AC- 3/23duty) main fuses,single phasing

preventer cum water level, Guard(Compe unit), Toggle

switch to by pass Single phase preventercum

WLG,indicating lamps forR-Y-Bphases, over load

relay.Automatic water level controller, Ammeter

incoming wires duty socket Crimped,Panel to be

erected on angle iron frame grouted on wall as

overload relay,thermal/Electronics star delta cutoff

timer,start-stop push buttons.The isolator overload

relay &cntractors ofL&T,Siemens or Cuttler Hamer

make only.Panel to be erected on angle iron frame

ground on wall (e)S/D upto 2.5 H.P.

143 Applying two coats of Birla or Asian acrylic lapy 132.00 Sqmt 40.59

(putty) & two coats of primer of approved brand and

manufacture on new wall surface to give an even shade

including thoroughly brushing the surface free from

mortar dropping and other foreign matter and sand

papered smooth.

144 Providing and fixing rolling shutters of approved make 5.00 Sqmt 3554.40

made of 80 mm wide M.S laths inter-locked together

through heir entire length and jointed together at the

ends by end locks mounted on specially designed pipe

shaft with bracket plates,guide channels and

arrangement for inside and outside locking with push-

pull operation including the cost of hood cover and

sprig etc.complete(A) Shutters having width below

145 Drilling of min. 250 mm dia. bore hole in all strata 90.00 Rmt 1240.28

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per

directed engineer incharge.

146 Supplying slotted PVC pipes of approved quality at site 90.00 Rmt 555.50

of work confirming to IS. 1239/1974 180mm dia.

147 Bore plug having 100 mm height made from M.S. plate 1.00 Nos 1161.62

with 3 holes at equal distance on circumference for nut-

bolts type, locking arrangement with nuts-bolts & lock

nuts of std. Make complete. For 250mm dia

148 Providing PVC insulated flat submersible cable as per 50.00 rmt 180.79

detailed technical specifications of R/C of GWSSB

conforming to IS 694, IEC 60227 / 60228.d)1 R x 3 C x

149 Suppling and installing 3 Phase Borewell 3.0 HP 1.00 Set 37130.63

Submersible Pump Sets Electric motor driven

conforming to I.S. 8034 and motor conforms to IS-

9283 working at 3 phase 400/440 volt 50 C/S A.C.

supply & 2900 R.P.M. cat

150 Providing and fixing check or non return pully wheel 1.00 Nos 1111.00

valve of 50 mm diameter.

151 Manufacture, supply and delivery of following ISI 45.00 rmt 152.51

marked HDPE pipes (IS:4984/1985 with latest

amendment) having material Grade PE-80 in

approximate 100 meter coil length or as per GWSSB

requirement with SS 316 nipple at both ends having

11 TPI threads as per specifications, press fitted and

bolted having nominal diameter as under as per

detailed technical specifications.

152 Constructing brick masonry chamber for underground 4.00 No. 7180.44

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm

intenal dimensions, total weight of cover with frame to

be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of

frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-

cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(iii) Inside dimensions 600mm

x 850 mm and 450mm deep for pipe lines with three

or more inlets.

153 Providing and fixing and floor 10.0 Kg. F/Cm2 working 110.00 Rmt 339.05

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including

making good the wall ceiling and floor.(G)110 mm

154 Providing and fixing and floor 10.0 Kg. F/Cm2 working 40.00 Rmt 696.90

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including

making good the wall ceiling and floor.(G)180 mm

155 Providing junction for rain water juncton chamber of 2.00 Nos. 9133.43

size 0.60x0.60x0.75m with excavation of size

1.96x1.96 m & 0.15m thick c.c.1:2:4 bed concrete

including brick masonary wall in CM 1:6 of 0.75m

height & 0.23m thick with 15mm thick cement plaster

inside & outside & 1.06x1.06 RCC (1:2:4) slab of

thickness 0.15m with CRS steel and 0.60mx0.45m cast

iron manhole cover with frame weight not less than

kg as per directed by Engineer-in-charge

156 Providing and installation Recharge pit of “RAIWOHA” 1.00 Nos. 109645.60

Make 3 layer RCC Precast Injection well system of size

1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V wire

screen of 0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and required

Air vent including all necessary excavation and

transportation at site including required filter media

for the recharge system as per site requirement.

157 Box cutting the road surface to proper slope and 375.00 Cum. 112.02

camber for making a base for road work including

removing the excavated stuff and depositing on the

road side slope as directed upto upto All lift and lead..

158 Construction of granular sub-base 150 mm thick by 159.00 Cum. 1276.64

providing coarse graded machine crushed B.T.

material satisfying MOST specification of grading I

(B.T. stone aggregate 53 mm to 26.5 mm 35 %, 26.5 to

4.75 mm - 45 % and 2.36 mm below - 20 % )including

spreading in uniform layer with motor grader on

prepared surface, mixing by mix in place method with

rotavator at OMC and compacting with vibratory roller

to achieve the desired density etc. complete.

159 Providing and laying wet mix macadam base course 154.00 Cum. 1313.00

250 mm thick in two layers using machine crushed

B.T. chips as per required gradation mixing with

required optimum quantity of water, conveying the

mix to site of work, spreading in to grade and camber

with mechanical paver and consolidation each layer

with vibratory roller including cost of material labour

plant and equipment etc. complete.

160 Compaction and finishing of cement concrete road by 732.00 Sqm 65.65

trimix process providing extra Labour charges for the

trimix vacume dewatering service process on cement

concrete road sutface by using vacuum dewatering

pump floater surface vibrator including making groves

and rough finish to surface including leveling etc

161 Providing and fixing pre-cast Rubber Dye inter locking 274.00 Sqm 707.55

concrete block 60mm thick with grade of concrete

M300 pnumatic compressed by mechanically pressed

and as per approved design including 75mm Sand

layer for levelling and filling the joint with sand in

proper line and level etc complete.

162 Providing and Laying homoginious Grey cement based 274.00 Rmt 374.92

concrete kerbing of size 30 cm x 30 cm x 10 cm size as

per detailed drawing having grade of concrete M25

grade, including necessary excavation, BBCC 1:5:10

cm as per ddetailed drawing fixing in line and level,

filling joints in CM 1:3 with smooth finished, white

washing three coats etc. complete as directed by

Engineer in charge.

163 Demolition of Brick work and stone masonry including 113.00 Cumt 591.68

stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift.(ii) In

Cement Mortar.

164 Demolition including stacking of serviceable materilas 26.00 Cumt 1137.19

and disposal of unserviceable materials with all lead

and lift. (i) R.C.C. work

165 Steel work, welded in built up sections framed work 750.00 kg 91.08

including cutting, hoisting, fixing in position and

applying a priming coat of read lead paint & two coat

oil paint. (A)In beams and joists, channels angles Tees,

flats, with connecting plates or angle cleats as in main

and cross beams. Hip and jack rafters, purlins

conneted to common rafters and the like.(Gate)

166 Providing and fixing concertina coil fencing with 199.00 Rmt 516.11

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt length,

upto 3mt height of wall with existing angle iron

(50mm x50mm x5mm )requird shaped As per

Directed Engeenier in charge. placed 2.4mt or 3.00mt

apart and with 4 horizontal R.B.T. reinforced barbed

wire(3 mm) , stud tied with G.I. staples and G.I. clips to

retain horizontal, including necessary bolts or

G.I.barbed wire tied to angle iron, all complete as per

direction of Engineer-in-charge, with reinforced

barbed tape (R.B.T.)/Spring core (2.5 mm thick) and

weight 43.478 gm/meter at compound wall for ESR

M4/ intakewell.

167 Constructing providing and fabricating cattle guard 5.00 Sqmt 5194.43

using channel section frame of size ISMC series

mm x 50 mm (Weight 9.20 kg/Rmt) and ISMC section

100 mm x 75mm (weight 11.50 kg/Rmt) intermediate

support for welding G.I.pipe at 12 Cm C/C of size

mm in a frame made of Channel section size 100 mm x

50 mm all round including fixing the unit on prepared

chamber of masonary wall using MS hold fast embeded

in masonary wall top as directed by Engineer in charge

and as per drawing and necessary required

arrangement etc complete.

168 Supplying of well rotted FYM manure with all lead and 16.00 Cum. 378.75

Lift including spreading mixing dressing and rolling

with hand roller etc. complete.

169 Scarifying the surface of Soil including spreading of 629.00 Sqm 26.26

DAP fertilizer mixing with Soil properly levelling gand

dressing of the plot

170 Supplying and planting semi carpet lawn in Gunny Bag 629.00 Sqm 121.42

and Cost of labour And including maintanatce .As per

Eng-in charge

171 Supplying And Planting box hedge Shurbs of Average 15.00 No. 103.01

hight 1ft-2 ft By providing and mixing FYM 2@ rate of

0.06cmt/pit with soil pesticide & Insectiside Plant

should be deisease Free and fungs free in 6inchx 8inch

polythene bag plastric bag or pots should be remove

carefully and soilt around the roots should not be

droped or distrub much bill shall be placed after

completions of maintanace period but not before

stablizing the shurbs.mortality rate to beinclusive .as

directed and approved by ECI. the ground coverage

should be dense and uniform throghout the planting

172 Supplying well Grown Shurbs Plants of Average hight 20.00 No. 103.01

3ft-4 ft and planting in 300x300x300mm size Pits By

Mixing Of FYM & Existing soil in ration 1:3 with soil

,Pesticide & insecticide .plants should be disease free

and fungus free in 8ftx10ft polythene bag plastric bag

or pots should be remove carefully and soilt around

the roots should not be droped or distrub much bill

shall be placed after completions of maintanace period

but not before stablizing the shurbs.mortality rate to

beinclusive .as directed and approved by ECI. the

ground coverage should be dense and uniform

throghout the planting area

173 Supplying well Grown Canna Bulb Plants of Average 15.00 No. 86.75

hight 1ft-2 ft and Providing in 2 row at 300mm/cc in

300x300x300mm size pits by Providing and Mixing Of

FYM @ 0.06cmt/pit with soil pesticide and insecticide

.plants should be disease free and fungus free in

8ftx10ft polythene bag plastric bag or pots should be

remove carefully and soilt around the roots should not

be droped or distrub much bill shall be placed after

completions of maintanace period but not before

stablizing the shurbs.mortality rate to beinclusive .as

directed and approved by ECI. the ground coverage

should be dense and uniform throghout the planting

174 Providing and planting of Khengar tree plants healthy 15.00 No. 961.70

and well-grown, of height not less than 3 ft, in polybags

or earthen pots, including excavation of pit of required

size, arrangement and placing of rubble at bottom for

proper drainage, refilling the pit with good quality

garden soil mixed with FYM, watering, application of

organic and chemical fertilizers, pesticides, all

complete including cost of labour, materials, and as per

direction of Engineer-in-Charge."

175 Bowing and developing flowering plants grown in 8.00 No. 10.10

nusery having approximate height 4 to 5 ft or Height

ad per Landscaps Plan with natural growith and nature

colour planted in alump of soil packed in polithyline

bag or Earthern pot. Including organic & chemical

fertilizer pesticides, fungicides hormones &

maintaining the plants uo to three months as deserted

green mahindi

176 Bowing and developing flowering plants grown in 5.00 No. 15.15

nusery having approximate height 4 to 5 ft or Height

ad per Landscaps Plan with natural growith and nature

colour planted in alump of soil packed in polithyline

bag or Earthern pot. Including organic & chemical

fertilizer pesticides, fungicides hormones &

maintaining the plants uo to three months as deserted

New block ficus.

177 Labour charges for planting various plantsafter proper 78.00 No. 40.40

anti termite treatment in pits including placing

property and filling the pit with requred prepared mix

soil and wetering and dispporting etc complete.

178 Maintance of the garder for 360 days after Complition 1.00 Job. 10100.00

of 3 month stipulated period is completed for

plantation o lawn and plants including applying second

round of proper antitermite tretment.

179 Providing and fixing brass screw doen stop cock (A) 15 1.00 Nos 287.85

180 Rubber Hose pipe 15 mm dia of approved brand and 120.00 Rmt 80.80

181 Providnig and fixing G I Nipple as directed. 1.00 No. 20.20

182 Earthwork in cuting in all sorts of soil and soft murrum 0.80 Cumt 129.28

including conveying and spreading the stuff,

embankment as and where directed within 200meters

from the end of the cutting with all required lead and

lift.(C) Above 400 Meters

upto 500 Meters.

183 Earthwork for embankment including breaking clods, 1067.80 Cumt 173.31

dressing with all lead and lift (excluding watering and

consolidation)(E) From Borrow area within all lead

184 Rolling of earthwork in layers with power roller 1068.00 Cumt 23.18

including filling in depressions which occur during the

process and Watering of earth work as directed.

185 Supply, installation, testing & commissioning of ISI 1.00 No 98432.21

approved electrical motor driven jockey pump set

having 10.8 m3/hr. @ 70m head. The pump unit shall

be a horizontally direct mounted motor. Unit shall

comprise the following minimum requirements: a)

Pump, b) Electric motor IE2, c) Foundation bolts, d)

Mating flanges with gasket and fasteners, e) Discharge

gauges, etc. complete in all respect, with labour.

186 Supply, installation, testing & commissioning of 1.00 No 25677.97

Priming tank, HDPE type, 1000 litres, with necessary

piping 100 mm size, G.I pipe for priming the pumps,

pipe of with butterfly valves for isolation, Water

Filling to priming tank by piping min. 50 mm size, with

all complete.

187 Supply, installation, testing & commissioning of 1.00 No 55635.60

Manifold (surge vessel) for fire hydrant system, min.

300 mm diameter, made from M.S plate, hydro tested

to 15 kg./cm2. with ball valves, header with couplings

for fitting pressure switches, pressure gauges etc.with

necessary isolation valves with all complete.

188 Supply, fabrication & erection of aboveground G.I. 'C'- 30.00 Mtr 398.01

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 25 mm dia.

189 Supply, fabrication & erection of aboveground G.I. 'C'- 30.00 Mtr 641.95

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 50 mm dia.

190 Supply, fabrication & erection of aboveground G.I. 'C'- 20.00 Mtr 1176.90

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 80 mm dia.

191 Supply, fabrication & erection of aboveground G.I. 'C'- 100.00 Mtr 1690.47

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 100 mm dia.

192 Supply, fabrication & erection of aboveground G.I. 'C'- 6.00 Mtr 2525.00

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 150 mm dia.

193 Supply, fabrication & erection of aboveground G.I. 'C'- 6.00 Mtr 3423.73

Class, ERW piping, conforming to IS:1239, part-I,

Heavy class up to 150 mm dia. and IS:3589, for size

200 mm dia. & above, thickness. G.I. pipe fitting's as

per IS: 1239, part-II, Heavy class for size 150 mm dia.

& below & IS: 3589, for size 200 mm dia. above,

flanges, nuts bolts & washers, 3 mm thick gasket, pipe

hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the system

pressure, hook-up etc.

Painting for piping, fittings & structural pipe support,

shall be two coat of zinc primer and two coats of fire

red conf. to IS: 5, Shade 536. Complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. 200 mm dia.

194 Supply, installtion, testing & commissioing of 10.00 Mtr 2020.00

Underground GI (ERW) piping conforming to IS:1239,

part-I, Heavy class ('C' class) up to 150 mm dia. and

IS:3589 Heavy class ('C' class), for 200 mm dia. &

above, min. 6.35mm thickness including Heavy class

fittings, anti-corrosive tape of size 150 mm wide x

mm thick, wrapping & coating with 13KV holiday

testing . Rates shall include sand bedding of 75mm dia

all around, backfilling of the excavated including

installation of heavy pipe fitting's, flanges, etc. 10 % of

all the welded joints shall be done radiographically

tested and 50% of the joints radiographed shall be the

"Field Joints". Hydrostatic testing for 2 hours at 150%

of the system pressure, hook-up etc., complete with all

accessories as per approved drawings, specicification

and direction of the Engineer-in-Charge, with all

complete. (Road Crossing) 100 mm dia.

195 Design, Supply and installation of Safety Signage made 1500.00 Sq. 9.41

of Zinc Sulphilde based glow in dark , Rigid sheet with inch

High Luminous property enclosed in a transperent

weather proof UV stabilized plastic pasted on 3 mm

thick clear acrylic sheet such as EXITS, EMERGENCY

EXIT, DO NOT USE LIFT DURING FIRE, FLOOR

MARKINGS, FIRE LIFT, STAIRCASE EXIT, FIRE ALARM

CALL POINT, FIRE HOSE REEL, FIRE HYDRANT POINT

196 Supply, Installtion, Testing & Commissioing of 50.00 No 556.36

Standard Response Sprinkler, Pendent Brass Sprinkler,

Quartzoid Bulb type with crome finish, nickel crome

platde, K factor K-80, Temp.- 68 C, 1/2" end connection

including resessed escutcheon. (UL Listed).

197 Supply, installation, testing & commissioning of 2.00 No 2824.58

pressure switch. (Range 0 to 16 kg/cm2)

198 Supply, installation, testing & commissioning of 150 2.00 No 2738.99

mm dia. dial Burdon Type Glycerine Filled pressure

gauge with isolation ball valve arrangements with

necessary isolation valves with all complete.( Range

199 Supply, Installation, Testing & Commissioning of Cast 3.00 No 2011.45

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 50 mm dia.

200 Supply, Installation, Testing & Commissioning of Cast 2.00 No 2567.80

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 80 mm dia.

201 Supply, Installation, Testing & Commissioning of Cast 2.00 No 3124.15

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 100 mm dia.

202 Supply, Installation, Testing & Commissioning of Cast 1.00 No 4493.64

iron body Butterfly valve according to IS: 13095, PN-

1.6, Iron Disc for size 150 mm dia. & below Lever

operated and above 150 mm dia. Gear operated

complete with mating flanges /ANSI class # 150 with

bolts & nuts washers, rubber gaskets 3 mm thick, etc.,

with all complete. 150 mm dia.

203 Supply, installation, testing & commissioning of Cast 3.00 No 1540.67

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 50 mm dia.

204 Supply, installation, testing & commissioning of Cast 2.00 No 2225.42

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 80 mm dia.

205 Supply, installation, testing & commissioning of Cast 3.00 No 3166.95

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 100 mm dia.

206 Supply, installation, testing & commissioning of Cast 1.00 No 5820.34

iron body Dual Plate Wafer Type NRV conf. to IS:

PN-1.6 complete with mating Flanges class # 150 with

bolts & nuts, washers, gaskets 3 mm thick, etc., with all

complete Accessories 150 mm dia.

207 Supply, installation, testing & commissioning of SG 1.00 No 1112.71

iron body SinglePlate Wafer Type NRV conf. to ASTMA

536, PN-1.6 complete with mating Flanges class #

with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories 50 mm dia.

208 Supply, installation, testing & commissioning of SG 1.00 No 1455.09

iron body SinglePlate Wafer Type NRV conf. to ASTMA

536, PN-1.6 complete with mating Flanges class #

with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories 80 mm dia.

209 Supply, installation, testing & commissioning of SG 1.00 No 1797.46

iron body SinglePlate Wafer Type NRV conf. to ASTMA

536, PN-1.6 complete with mating Flanges class #

with bolts & nuts, washers, gaskets 3 mm thick, etc.,

with all complete. Accessories 100 mm dia.

210 Supply, installation, testing & commissioning of Y 1.00 No 5563.55

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 80 mm dia.

211 Supply, installation, testing & commissioning of Y 1.00 No 7275.42

Type Strainer complete with mating flanges with bolts

& nuts, washers, gaskets 3 mm thick, etc., with all

complete accessories. 100 mm dia.

212 Supply, installing, testing and commissioning of 1.00 No 4194.07

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary complete

accessories. 80 mm dia.

213 Supply, installing, testing and commissioning of 1.00 No 6162.71

Normax make CI heavy duty ball type foot valve with

flanges, nut bolts, gaskets etc. with necessary complete

accessories. 100 mm dia.

214 Supply, installation, testing & commissioning of Four 1.00 No 8987.29

way fire brigade Inlet connection with 63 mm dia.

stainless steel (SS304) instantaneous male inlets with

built in non return valve in each inlet with 150 mm dia.

header pipe, suitable rubber cap and GI chain including

nuts, bolts, washers, gasket 3 mm thick, etc. with all

215 Supplying FIRE bucket round bottom of 9 liters 8.00 No 1027.12

capacity made out of 24 gauge G.I Sheet with extra

handle at bottom duly painted white inside and Red

out side with FIRE mark. Filled with dry-sand and kept

on existing stand provided or hung on wall hook.

216 Supplying and erecting floor mounting Stand for 2.00 No 5563.56

keeping four nos. of FIRE buckets comprising

mm in length, 900 mm height frame made out of

30mm x 30 mm x 4 mm angle iron with cross supports

legs, welded with 4 hooks and duly painted with one

coat of primer and two coats of approved enamel PO

red paint.

217 Supply & installation of stainless steel body Orifice 5.00 No 1069.91

Plate of suitable inner bore along with matching flange -

as per specification & requirement as per hydraulic

calculation.

218 Supply, installation, testing & commissioning of 5.00 No 5435.17

Oblique pattern type stainless steel (SS 304) single

headed External Fire Hydrant Valve with 63 mm dia.

female instantaneous outlet conf. to IS: 5290, type - A,

including mating flanges, galvanised nuts, galvanised

bolts/studs, washers & gaskets 3 mm thick with all

219 Supply, installation, testing & commissioning of 63 mm 5.00 No 1754.66

dia. stainless steel (SS 304) Universal Branch Pipe

conf. to IS:

220 Supply & installation, testing & commissioing of Fire 5.00 No 6967.29

Fighting Hose - conf. to IS : 636, type B (type- 3), The

fire hose shall be 15 m long with 63 mm dia. stainless

steel (SS 304) couplings conf. to IS: 903, at both the

ends for connection with the hydrant valve and the

branch pipe.

221 Supply, installation, testing & commissioning of 5.00 No 2525.00

fabricated from 3 mm MS sheet, hose box of size-450

mm x 600 mm x 250 mm - painted with Fire Red as per

IS: 5, shade no. 536 front 3 mm thick transparent glass

with lock & key, handle and brass hinges - to

accommodate one number of 15 mtr long hose and one

number of universal branch pipe, including supporting

arrangement with civil work.

222 Supply, Installation, testing & commissioing of 5.00 No 7403.82

Swinging type mild steel hose reel drum with 20 mm

dia. x 30 mtr. rubber hose as per IS: 884. The mounting

stand shall be of mild steel and the hose shall be fitted

with a SS shut-off nozzle & SS ball valve of 25 mm dia.

including supporting arrangement with all complete.

accessories

223 Supplying, fixing & testing of of CI ball Valve 25mm dia. 15.00 No 706.14

224 Supplying, fixing & testing of New Battery of diesel 1.00 No 15834.75

engine 150 Amp.

225 Supply and installation of Diesel Tank For Diesel 1.00 No 16690.67

Engine With All Accessories 100 Ltrs.

226 Supplying, filling & testing lube oil for diesel engine 20.00 Ltrs 320.98

227 Supply and commissioning of Oil Filter. 1.00 No 706.14

228 Supplying, filling of diesel in diesel engine tank 75.00 Ltrs 89.87

229 Supply and commissioning of Diesel Filter 1.00 No 427.97

230 Supplying, filling & testing coolant to engine cooling for 20.00 Ltrs 239.66

231 Filling Of Gaps Between pipe and Core Cutting Hole 16.00 No 299.58

With Chemical and Cement

232 Steel work, welded in built up sections framed work 150.00 Kg 84.13

including cutting, hoisting, fixing in position and

applying a priming coat of read lead paint & two coat

oil paint. (A)In beams and joists, channels angles Tees,

flats, with connecting plates or angle cleats as in main

and cross beams. Hip and jack rafters, purlins

conneted to common rafters and the like.

233 Supplying & erecting XLPE(IS:7098)(I)-88 ISI 20.00 Mtr 136.35

unarmoured copper cable 1.1 KV grade to be erected

as directed of following size. (E) 3 core 2.5 Sq. mm for

pressure switch

234 Providing and erecting XLPE(IS:7098)(I)-88 ISI 20.00 Mtr 285.83

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump)

(B) 3 core 4 Sq. mm

235 Providing and erecting XLPE(IS:7098)(I)-88 ISI 20.00 Mtr 497.93

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable. (Only Fire Panel to Fire Pump)

(D) 3 core 10 Sq. mm (Only Fire Panel to Fire Pump)

236 Providing and erecting XLPE(IS:7098)(I)-88 ISI 20.00 Mtr 213.11

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe at road crossing or floor of

following size of cable for Diesel Engine Battery

Charger (A) 3 core 2.5Sq. mm

237 Supply, Filling and Fixing of approved make ABC type 6.00 No 1968.64

fire extinguisher - 6 Kg. Capacity as per IS:15683 & IS :

238 Supply, Filling and Fixing of approved make CO2 type 6.00 No 5520.76

fire extinguisher. Capacity 4.5 Kg. (conforming to IS-

239 Supply, Filling and Fixing of approved make ABC 2.00 No 3423.73

Moduler type automatic fire extinguisher. Capacity

Kg. (conforming to IS-15683).

240 Submitting the application to obtain Fire Plan 1.00 No 202000.00

Approval and After Completion of Work Obtain Final

Fire NOC for 3 Year.

241 Supply, Installation and commissioning of Air Release 1.00 No 1412.29

Valve, 25 mm Dia. connection.

242 Supply, Installation and commissioning of Fire Alarm 1.00 No 15150.00

Panel Conventional type, 2 zone, with complete

accessories.

243 Supply, Installation and commissioning of smoke 50.00 No 1027.12

detectors / heat detectors, with complete accessories.

244 Supply, Installation and commissioning of plug in base 50.00 No 256.78

for the smoke detectors, hooters, with complete

accessories.

245 Supply, Installation and commissioning of Audio 5.00 No 1069.91

hooters , with complete accessories.

246 Supply, Installation and commissioning of Manual Call 5.00 No 1010.00

Points, with complete accessories.

247 Providing and erecting XLPE(IS:7098)(I)-88 ISI 600.00 Mtr 176.75

armoured cable multistrand Copper conductor for

KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (A)

core 2.5 Sq. mm for Fire Alarm System

248 Core cutting in wall and in RCC slab with size as below: 6.00 No 342.37

50 mm dia. Hole

249 Core cutting in wall and in RCC slab with size as below: 4.00 No 427.97

80 mm dia. Hole

250 Core cutting in wall and in RCC slab with size as below: 2.00 No 513.56

100 mm dia. Hole

251 Core cutting in wall and in RCC slab with size as below: 2.00 No 599.15

150 mm dia. Hole

252 Core cutting in wall and in RCC slab with size as below: 2.00 No 855.93

200 mm dia. Hole

253 Supplying, installing, testing and commissioning of 1.00 Set 447652.54

Kirloskar make diesel engine driven fire hydrant pump

set, suitable for automatic operation and consisting of

horizontal type centrifugal end suction back pull-out,

top discharge pump with cast iron body and bronze

impeller, mounted on M.S. fabricated common base

plate with coupling, coupling guard, foundation bolts

and all necessary accessories, complete as required.

The pump shall be of Model KFE, having a discharge

capacity of 137 m³/hr at 70 meters head, driven by a

62 HP diesel engine, 3 phase, with suction and delivery

size of 125 mm x 100 mm.

254 Fire Hydrant Panel suitable for 10 HP Jockey Pump, 62 1.00 No 141400.00

HP (137 m³/hr @ 70 m head) Diesel Engine Operated

Pump, consisting of Incomer with MCCB (1 No.), R Y B

Indication (1 Set) and VAF Digital Meter (1 Set);

Outgoing with F2 – 10 HP DOL Starter for Jockey

Pump, F3 – Auto On/Off Diesel Pump with Battery

Charger, Control Circuit with Auto/Manual On/Off,

On/Off Trip Indication and On/Off Push Button;

Fabrication duly powder coated in PO Red Colour,

fabricated from 14/16 SWG GI Sheet with IP-42

Protection, fixed type floor mounted with bottom cable

entry, complete as required.

255 Pay Legal Fees to Concern Authority for Obtaining Plan 1004.00 Sq.mt 12.12

Approval and Final NOC

256 Dismentling of doors, windows, ventilators etc. (wood 56.00 No. 201.79

or steel) shutters including chowkhats architraves,

holdfasts and other attachment etc. complete and

stacking them within all lead and lift (ii) Not Exceeding

3 Sq.M. in area.

257 Dismentaling tiled of stone floors laid in mortar 348.00 Sqm 51.82

including stacking of serviceable materials and

disposal of unserviceable materials with all lead and

258 Dismentling wood work, wrought framed and fixed in 10.00 Cum 1891.33

fram es trusses including stacking the materials with

all lead and lift.

259 Demolition of terrace including stacking of serviceable 191.00 sqm 68.59

materilas and disposal of unserviceable materials with

all lead and lift.(i) Brick tile covering.

260 Demolition including stacking of serviceable materilas 53.50 Cum 1137.19

and disposal of unserviceable materials with all lead

and lift. (i) R.C.C. work

261 Demolition of Brick work and stone masonry including 216.37 Cumt 591.68

stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift.(ii) In

Cement Mortar.

262 Dismentling steel work including distempering and 3439.00 Kg 3.94

stacking the materials with all lead and lift.

263 Dismentling C.I. pipes G.S.W.pipes abd A.C. rain water 147.00 Rmt 80.72

pipes with fittings and clamps including stacking the

materials with all lead and lift ( for any dia, of pipe)

264 Dismantling santtary fittings like wash basin . W.C. pan 6.00 Nos 436.07

Indian and European type, flushing tank etc. including

stacking the materials with all lead and lift.

265 Point wiring for Tissino / Modular secondary light 38.00 Pt. 167.66

point with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires, in below type of

pipe to be erected complete with earth continuity and

necessary connection with primary light with

accessories erected on Metal / PVC / wooden box

covered with 3 mm thick PC(Polycarbonate) / Acrylic

sheet for open / concealed wiring. with necessary

Lamp holder / ceiling rose / H.D.Connector as directed.

Note:- Maximum up to 6 mtrs length, excess will be

considered as Mains for Secondary Point. (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete

266 Point wiring for Light / Bell with 2-1.5 sq.mm & 214.00 Pt. 485.81

earth wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand copper

wires up to 10 mtr length , in below type of pipe

erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type,

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector

as directed.(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat.III

267 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 62.00 Pt. 674.68

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires

up to 10 mtr length, in below type of pipe erected

with 6A Modular type switch and hum free EME step

type electronic fan regulator mounted and

accessories with earth continuity of following type

erected on PVC / Metallic/Wooden box, single

mounting base frame covered with

textured/metallic/white front plate modules erected

on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat.III

268 Point wiring for Individual Plug with & earth wire of 6.00 Pt. 510.05

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete

with Modular type switch & 5 pin Plug erected on PVC

/ Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [I] For 6A

Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from

nearby switchboard/mcb db board (f) with medium

class Rigid PVC pipe and accessories erected concealed

in wall/ceiling complete Cat.III

269 Point wiring for Individual Plug with & earth wire of 15.00 Pt. 871.63

1.5 sq.mm (Green) both are of ISI marked 1.1 KV grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete

with Modular type switch & 5 pin Plug erected on PVC

/ Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe

erected with following type of accessories. [III] For

16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire

with 2.5 sq.mm ( green) earthing wire from mcb d b

board. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat.III

270 Point wiring for on board Looped Plug with 6A 49.00 Pt. 257.55

Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories Cat.III

271 Providing following type of Modular Type Accessories 44.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (3) Two Pin/RJ-11 Telephone

Socket [A] For One Gang Cat.III

272 Providing following type of Modular Type Accessories 29.00 Ea. 25.25

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (7) Blank Plate Single Cat.III

273 Providing following type of Modular Type Accessories 44.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket Cat.III

274 Providing and erecting ISI mark Medium class RIGID 52.00 Mtr. 24.24

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved

manner as directed (a)20 mm

275 Providing and erecting ISI mark Medium class RIGID 1012.00 Mtr. 33.33

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution &

Clamps with following dia of pipes, in approved

manner as directed (b) 25 mm

276 Providing and erecting Mains with 1.1 KV grade FRLS 1395.00 Mtr. 82.82

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed

in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) With

medium class Rigid PVC pipe and accessories (b)

wire 2.5 sq. mm

277 providing and erecting Mains with 1.1 KV grade FRLS 60.00 Mtr. 147.46

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall

/ ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class

Rigid PVC pipe and accessories (b) 2 wire 6 sq. mm

278 providing and erecting Mains with 1.1 KV grade FRLS 200.00 Mtr. 260.58

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall

/ ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class

Rigid PVC pipe and accessories (h) 4 wire 6 sq. mm

279 providing and erecting Mains with ISI marked, 1.5KV 57.00 Mtr. 56.56

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required. (e) One wire 6.00 sq. mm

280 providing and erecting Mains with ISI marked, 1.5KV 51.00 Mtr. 91.91

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required. (f) One wire 10.00 sq. mm

281 providing and erecting Mains with ISI marked, 1.5KV 18.00 Mtr. 142.41

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required. (g) One wire 16.00 sq. mm

282 providing and erecting Mains with ISI marked, 1.5KV 10.00 Mtr. 236.34

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of

following size (Specifically for control panel, relays,

power switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts if

required. (h) One wire 25.00 sq. mm

283 Supplying and erecting Flexible PVC insulated multi 60.00 Mtr. 22.22

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed. (c)

Sq.mm 2 core round/ flat PVC sheathed

284 Supplying and erecting Flexible PVC insulated multi 86.00 Mtr. 46.46

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed. (e)

Sq.mm 3 core round PVC sheathed

285 Supplying & erecting approved make Telephone Cable 1100.00 Mtr. 20.20

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections. [A] Conductor Size

0.5 mm (a) Unarmoured (2) Two Pairs

286 Supplying & erecting approved make Telephone Cable 20.00 Mtr. 199.98

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections. [A] Conductor Size

0.5 mm (b) Armoured [Jelly Filled] (2) Twenty Pairs

287 Supplying & erecting approved make LAN cable of 1100.00 Mtr. 47.47

following size in existing pipe as per direction [C] CAT -

288 Providing & erecting main Distribution (MDF) indoor 1.00 Ea. 1368.55

type, back mounted frame as per DoT standard

approved with krone strips (b) Suitable for 20 pair

289 Providing & erecting main Distribution (MDF) indoor 1.00 Ea. 1747.30

type, back mounted frame as per DoT standard

approved with krone strips (c) Suitable for 50 pair

290 Providing & erecting Switch board for Computer or 44.00 Ea. 1133.22

electric apparatus consisting of following modular

type accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame

covered with textured/metallic /white front

plate,modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories

291 Decorative call bell Ting-tong box type 250 volts 10.00 Ea. 71.71

complete erected

292 Supplying and erecting LED indoor fittings with LEDs 84.00 Ea. 535.30

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

shown.) (A) Tube Light with integral driver (v) 36-40

Watts, Surge-2 KV, IP-20, conventional 4 feet Cat.III

293 Supplying and erecting led lamps with following 14.00 Ea. 112.11

wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting suitable

for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED

Lamps integral type, with PC diffuser suitable LAMP

holder (ii) 5 to 8 watts Cat.III

294 Supplying and erecting LED indoor fittings with LEDs 103.00 Ea. 758.51

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

shown.) (A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision for

spring loaded mounting clips complete.IP20 (iv) 22-24

watts, Surge-2 KV Cat.III

295 Supplying and erecting LED indoor fittings with LEDs 21.00 Ea. 1794.77

of wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be

made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder

coated and high U.V. & corrosion resistance with

diffuser housed in aluminium casted body with

company mark/name

160V to 270V,Power Factor more than 0.95, THD <

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

shown.) (B) LED Panel Light with provision for Plane

front frame with translucent cover fixed to housing

complete.IP20 (vi) 36 watts, 24" x 24", Surge- 2KV

296 Supplying and erecting LED street light / Flood light 21.00 Ea. 4997.48

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die

cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.) (A) Street Light (IP-65),

Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (ii)

above 48 to 60 Watts Cat.III

297 Supplying and erecting LED street light / Flood light 2.00 Ea. 4819.72

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die

cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser

and Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 &

LM-80 certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.) (C) Post Top Lantern LED

fitting comprises of finish cast aluminum spigot and

spun aluminum canopy fixed with opal polycarbonate,

pipe arrangement for vertical mounting driver and

accessories wired upto terminal block.IP 65 (ii)32-

40W Cat.III

298 Providing and erecting Approved make Four pole 17.00 Ea. 6173.12

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100% of ICU

only Cat III

299 Providing and erecting Approved make Four pole 6.00 Ea. 8055.76

moulded case circuit breaker having breaking capacity

ICU of 35 KA. at 415 V. having normal current rating

125A. with Fixed thermal & magnetic release suitable

to work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100% of ICU

only Cat III

300 Providing and erecting Approved make Four pole 2.00 Ea. 20946.39

moulded case circuit breaker having breaking capacity

ICU of 35 KA. and above at 415 V . having normal

current rating 250A. with variable thermal & magnetic

release suitable to work on A.C.supply 50 c/s. with all

internal connections, spreader tinned copper &

complete erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

301 Providing and erecting Approved make Earth fault 1.00 Ea. 5415.62

Relay suitable to mount with inter connection suitable

to following size of moulded case circuit breaker

having CT ratio & MCCB rating as following along with

shunt trip 220V AC. with all internal connections &

complete erected in existing M.S.housing. (3) 250 A -

400 A , CT Ratio 1/400

302 Supplying and erecting triple pole & neutral 440V / 1.60 Rn.Mt 1961.42

500V panel mounting Copper Busbars with four equal r

Nos. of electrolyte bus having current density not more

than 1.6 Amp. / sq.mm (Rated current / cross section

area) duly wrapped with colour insulating tape for

phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators,

main cable socket to each bar, erected in existing

cubical panel with necessary connections. (A) Suitable

for 100 Amp. Capacity

303 Supplying and erecting triple pole & neutral 440V / 1.60 Rn.Mt 3202.71

500V panel mounting Copper Busbars with four equal r

Nos. of electrolyte bus having current density not more

than 1.6 Amp. / sq.mm (Rated current / cross section

area) duly wrapped with colour insulating tape for

phase sequence of following current carrying capacity,

erected with necessary bus bar supports /insulators,

main cable socket to each bar, erected in existing

cubical panel with necessary connections. (B) Suitable

for 200 Amp. capacity

304 providing and erecting Miniature circuit breaker single 21.00 Ea. 270.68

pole 0.5A to 2A system and having breaking capacity

10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III

305 providing and erecting Miniature circuit breaker single 120.00 Ea. 112.11

pole 6A to 25A suitable to operate on 240 V A.C.

system and having breaking capacity 10 KA to be

erected in existing box. confirming to IS 8828/1996

with ISI Mark Cat.III

306 Providing & erecting 240 V MCB double pole switch for 4.00 Ea. 278.76

lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity (A) 6 to 32 Amp. Cat.III

307 Providing & erecting 240 V MCB double pole switch for 10.00 Ea. 295.93

lighting Load (B Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity (B) 40 Amp. Cat.III

308 Providing & erecting 415V MCB Four Pole Switch for 5.00 Ea. 638.32

Lighting Load (B curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (b)40 Amp. Cat.III

309 Providing & erecting 415 V MCB Four Pole for Motor & 12.00 Ea. 668.62

Inductive Load (C Curve) having 10KA breaking

capacity & confirms to IS :8828 in existing box having

following capacity (b)40 Amp. Cat.III

310 Providing and erecting Sheet Steel powder coated MCB 1.00 Ea. 629.23

distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable for (A) single phase incoming and horizontal

single phase outgoing (b) sheet steel double door (IP-

311 Providing and erecting Sheet Steel powder coated MCB 3.00 Ea. 1492.78

distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable for (A) single phase incoming and horizontal

single phase outgoing (b) sheet steel double door (IP-

43) (iv)12 way

312 Providing and erecting Sheet Steel powder coated MCB 8.00 Ea. 2339.16

distribution board - flush / surface mounted fitted

with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without

MCB to house appropriate nos. of MCBs.(The DBs

should be used of same company of MCB to be used)

suitable for (B) three phase incoming and single phase

horizontal type outgoing Per phase isolation type

(PPI) (b) sheet steel double door (i)4 way

313 providing and erecting Approved make RCCBs 28.00 Ea. 1969.50

conforming to IS: 12640 and having sensitivity of

mA and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as

directed (i) 25 Amps.DP Cat.III

314 Providing and erecting Annealed bare Copper wire 8 to 11.00 Kg 794.87

315 Providing and erecting Pipe type earthing having 150 6.00 Ea. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth

pit complete with necessary 8 SWG earth wire.

316 For using salt and charcoal / coke as required for pipe 6.00 Ea. 171.70

type earthing.

317 Supplying & erecting in earthpit of minimum bore dia. 5.00 Ea. 7095.25

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250

Micron galvanising, connection terminal dia of

mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation

suitable for following type of applications with

chamber and heavy duty cover (A)(approved make

OEM has to submit test certificate including value of

earth resistance of installation duly stamped and

signed by agency and officer Incharge has to ensure

the value of earthing resistane mentioned in test

Certificate) & having back filling compound of (B)

Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm

/ meter testing as per IEC 62561-2017, Voltage drop:-

< 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time

Necessary test report must be submitted by Agency.

[B] For Electrical installation up to 11 KV located in

other than normal soil i.e. Soft Rock, Marshy Soil etc.

-Length of Pipe : 2 mtr

-Back filling Compound :1 no. Bag of 25 Kg.

318 Providing & erecting weather proof, dust & vermin 4.00 Sq.Mtr 10468.65

Providing & erecting weather proof, dust & vermin

proof, floor mounted front operated indoor type

cubical panel board necessary IP-42 and above

protection as per approval from engineer incharge

made from 14 SWG thick CRC M.S. sheet for outer body

& doors, 16 SWG thick CRC M.S.sheet for internal

partitions with necessary accesories , supporting

angles/ flats channel including cutting, bending,

drilling, welding, riveting with internal partitions &

cable alley as per requirements & instruction of

engineer-in-charge with erection of supplied switch

gears, BUSBARS, suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for

measuring instruments, earth bus & earth bolts,

foundation flange - bolts-base Plates, sufficient nos. of

hinged doors, handles with locking arrangement and

rubber gasket,heavy duty end terminal

connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter

connecting mains & Copper Aluminium strips, meters,

Fuses etc. The dimension shall be measured excluding

base beams) The panel shall be supplied with

following approved manufacturers with following size.

(A) locally fabricated panel board (i) with 350 mm

319 Providing , erecting , fabricating the M.S. structure as 70.00 Kg. 77.77

per requirement on site incorporating proper size of

M.S. angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing

duly painted with one coat of red oxide with erection

on site as per direction of engineer in charge with

necessary grouting, cementing, plastering & finishing

320 Providing and erecting XLPE(IS:7098)(I)-88 ISI 70.00 Mtr. 92.92

armoured cable Aluminium conductor for 1.1 KV. to

be laid on wall with necessary clamps or in existing

trench / pipe of following size of cables. (B) 2 core

321 Providing and erecting XLPE(IS:7098)(I)-88 ISI 60.00 Mtr. 284.82

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (C)

1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core)

322 Providing and erecting XLPE(IS:7098)(I)-88 ISI 80.00 Mtr. 490.86

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (E)

1/2 core 95 Sq. mm ( 50 Sq. mm 1/2 core)

323 Providing and erecting XLPE (IS:7098)(I)-88 ISI 302.00 Mtr. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (B) 4 core 6 Sq. mm

324 Providing and erecting XLPE (IS:7098)(I)-88 ISI 150.00 Mtr. 140.39

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (C) 4 core 10 Sq. mm

325 Making trench in soft soil of suitable width of 90 cm 410.00 Mtr. 55.55

deep for laying cable or locating the fault all over the

run and back filling the same and making the surface

as normal ground.

326 Supplying following size of Light duty “A” Class G.I . 25.00 Mtr. 471.67

Pipe & erecting as directed by Engineer-in-charge. (C)

80 mm dia.

327 Providing & laying approved make Double walled 365.00 Mtr. 62.62

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting accessories

of same material at required depth in existing trench

for laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

328 Providing & laying approved make Double walled 20.00 Mtr. 95.95

corrugated pipes (DWC) of polyethylene(conforming

to IS 14930 II )with necessary connecting accessories

of same material at required depth in existing trench

for laying of cable. below ground / road surface for

enclosing cable (C))90 mm outer dia

329 Providing and, fixing heavy duty flange type brass 6.00 Ea. 38.38

cable gland with rubber ring for PVC insulated

armoured cable complete with out going tails,

insulating tape etc for following size of cables. (C) 2 to

4 core 10 Sq. mm

330 Providing and, fixing heavy duty flange type brass 6.00 Ea. 75.75

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

cables. (B) 3 & 1/2 core 35/50 Sq. mm

331 Providing and, fixing heavy duty flange type brass 4.00 Ea. 131.30

double compression type cable gland with rubber

ring for PVC insulated armoured cable complete with

out going tails, insulating tape etc for following size of

cables. (D) 3 & 1/2 core 95 Sq. mm

332 Solder less crimping type Aluminium lugs conforming 144.00 Ea. 6.06

to IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

333 Solder less crimping type Aluminium lugs conforming 24.00 Ea. 13.13

to IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (B) 10 Sq.mm

334 Solder less crimping type Aluminium lugs conforming 24.00 Ea. 20.20

to IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (D) 35/50 Sq.mm.

335 Solder less crimping type Aluminium lugs conforming 16.00 Ea. 40.40

to IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (G) 120 Sq.mm.(F) 95 Sq.mm.

336 Providing and erecting Approved make Ceiling fan 62.00 Ea. 1596.81

with double ball bearing ISI mark with condenser A.C.

23OV.50 c/s.1200 mm. sweep complete, canopy

erected on existing hook or clamp with earthing. [Make

shall be approved by Engineer in charge]

337 Replacing old & u/s by Supplying and erecting 19 / 20 62.00 Mtr. 108.07

mm. nominal bore Medium Class M.S. Pipe down rod

erected duly painted for fan complete with proper

insulation without leakage and earthing.

338 Supplying & erecting fan hook box of 10 mm M.S. 62.00 Ea. 108.07

round bar bounded to the RCC bars up to 50mm length

each side and pierced through a 16 Gauge M.S. box /

Heavy Duty PVC box complete erected concealed in

Ceiling with necessary finishing.

339 Providing 2.5mm.thick laminated acrylic sheet to cover 62.00 Ea. 18.18

the fan hook or Fan box.

340 Supplying & erecting approved make low noise 17.00 Ea. 1366.53

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame. 250mm with

RPM Cat.II

341 Supplying and erecting approved make Octagonal pole 9.00 Ea. 6874.06

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as

per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per

details given by manufacturer considering site

requirement. (C) 5 Mtr. Long 70 mm Top X 130 mm

bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M16 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole

weight 46 kg

342 Supplying & erecting approved make SMC press 10.00 Ea. 515.10

moulded composite FRP. loop-in, loop-out approx.

2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements

with mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps& earth

bolt of following size of box. (B) 250mm x 200mm x

100mm [deep]

343 Supplying and erecting Street light pole bracket 7.00 Ea. 491.87

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts

and bolts for fixing the brackets and having spread of

0.5 mtr. Length with 110 deg.with vertical plane and

suitable welded stiffener reducer and nipple with

check nut complete painted with one coat.of Red oxide

/ PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms. [A] Single Arm

bracket 0.5 Mtr

344 Supplying and erecting Street light pole bracket 2.00 Ea. 622.16

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts

and bolts for fixing the brackets and having spread of

0.5 mtr. Length with 110 deg.with vertical plane and

suitable welded stiffener reducer and nipple with

check nut complete painted with one coat.of Red oxide

/ PU base primer and two coats of Aluminium / PU

paint. paint with following nos of arms. [B] Double Arm

Bracket 0.5 Mtr

345 Supplying and erecting B class galvanised iron pipe 32 8.00 Ea. 343.40

mm outside dia 45 cm long duly welded on 20 cm x

cm x 3 mm thick M.S. base plate, erected on wall or

corner for mounting street light luminaire with

necessary hardware materials duly painted.

346 SITC of Digital / PCM / TDM EPABX System having 1.00 Ea. 77077.14

SMT design, system with flexible universal slots.

Inbuilt Auto attendant facility, Minimum 15 Nos.

conference, Analog extension line, Calling GSM, E&M

line, PRI / EI & VOIP program me through Analog

telephone digital key from Ethernet, public address

cord, shall have unrestricted simultaneous dialing

QSIG protocol on PRI, 95 / STD / ISD / Local-Locking,

Class of Service, Quick Dial-Single Digit dialing of any

two external number, Once only ring device, Chairman

/ Secretary - Do not disturb Facility, Power Down

Mode, Hot Line, Hot Outward Dialing, Day Night Mode,

Auto Call Back, Barge-in, Call Pick Up & Call Transfer,

Call transfer while Ringing with Voice Guide System,

(DISA), Caller ID (CLI), CLI Base ECF, CLI Base routing

Internet Ready Port, External Music Port, Call

Budgeting, Call Most Calculation (ASMDR), DID Direct

Inverse Dialing, External Music Input, Fax Homing,

Global Directory Printing with following capacities

[[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ] [C] No of Extension 48, No

of Junctions 9, 8 Port IP Resource in-built, 4 Port Web

base Video Conferencing, No of expandable ports :

Operators Console - 01 Compatible : ISDN

347 Providing & erecting, programming, testing of 1.00 Ea. 5992.33

chairman unit microphone with flexible stem of

mm in length and light ring built in loud speaker ,two

head phone socket ,attractive design ,priority button

for chairman microphone,built in volume control for

head phones,chime tone facility to precede chairman

priority calls,microphone on/off button,red indicates

for microphone is active,frequency response -400Hz to

10kHz,nominal acoustic input -85 dB SPL [[Approved

by Competent Authority i.e. not Below the rank of

Executive Engineer ]

348 Providing & erecting, programming, testing of Delegate 8.00 Ea. 5565.10

unit microphone with flexible stem of 480 mm in

length and light ring built in loud speaker ,two head

phone socket ,attractive design ,built in volume control

for head phones,chime tone facility to precede

chairman priority calls,microphone on/off button,red

indicates for microphone is active,frequency response -

400Hz to 10kHz,nominal acoustic input -85 dB SPL

[[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

349 Supplying & erecting dual channel amplifier ,power 1.00 Ea. 11128.18

handling capacity of 180 watt ,four micro phone inputs

with independent level control ,built in FM tuner,with

preset memories,USB drive & SD card for MP3

playback ,100v /telephone input with priority and

VOX,frequency response-80 Hz to 18k Hz Philips /

/distortion less than 1% @ rated power up to 50 units

[[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

350 Supplying and erecting ceiling speaker with rated 6.00 Ea. 2569.44

power of 30 watt/power tapping 30/15/7.5 watt

available,opening angle 180 degree H * 77 degree V

,sound pressure level 88 dB ,frequency response of

70Hz to 20KHz [[Approved by Competent Authority i.e.

not Below the rank of Executive Engineer ]

351 Providing and erecting Inverter based approved make 2.00 Ea. 48257.80

split air-conditioning unit consisting of condensing

unit with variable speed fan motor, inverter type

hermetically sealed rotary compressor with

accessories etc. duly connected separately erected

evaporating unit and blower motor with its

accessories by means of extra supplied proper

insulated copper tubing,drain PVC pipes suitable for (

cost includes Eco Friendly green gas charging and 15A

plug top & Remote Control & MS Stand) with necessary

core cutting. (1)For ISEER Range (KWH/KWH)(3.1 to

3.99) (B) for 1.5 ton capacity - Premium Cat.

352 Supplying and erecting insulated pair of soft copper 16.00 Rmt 965.56

tubing open or concealed including power and control

cable,necessary PVC drain pipes for Split AC machine

up to 4 TR capacity

353 Providing & erecting water cooler having storage 2.00 Ea. 55893.40

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour

@ an ambient temp of 45˚ C. The outlet temp. of the

water should drop by 15˚C within a hour, The water

cooler should be comprising of hermetically sealed

compressor, fan motor, condensing unit, water tank

surrounded by evaporating, coil, thermostats, relay

etc.complete with necessary inlet & outlet connection.

The body of water cooler will be made from Stainless

354 Supplying & erecting 5 stage single reverse osmosis 2.00 Ea. 29187.99

water purification system with M.S. powder coated

frame, prefilter housing with 'O' ring presediment

filter GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post

carbon filter auto low & high pressure switches with

following size of storage tank & LPH capacity & erected

as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster

355 Supplying and erecting approved make panel 1.00 Ea. 1275.63

mounting type Digital Voltmeter having 3 digits LED

display, 0 to 750 AC Volts range erected on existing

panel board with all connection, wiring etc .with

manufacturers calibration certificate.

356 Supplying and erecting approved make panel 1.00 Ea. 1558.43

mounting type Digital Ammeter having 3 digits LED

display, external CT operated, calibrated for 0 to

Amps suitable to operate on 500 Volt AC , erected on

existing panel board with all connection, wiring etc

.with manufacturers calibration certificate.

switch for 3 phase AC Supply 500 V on existing panel

board with necessary connections.

358 Providing & erecting L.T. Current Transformer with 3.00 Ea. 274.72

bar primary 50/5 to 1000/5 ratio 15 VA burden

erected in existing CRCA box duly secured with

insulating materials connected to the meter

359 Supplying and erecting approved make suitable panel 9.00 Ea. 43.43

indicator LED type lamp, lens cover, complete erected

with necessary connections.

360 SITC of Vertical Air Termination Solid aluminium with 6.00 Ea. 9416.23

Base- 10 mm dia and 1000 mm long. Air Termination

Base tested for conditioning, Ageing Test & Lightning

impulse current withstand test: 100 kA of 10/350µs

waveform in an accredited Third party laboratory as

per 6.3 & 6.4 of IEC 62561-1 2017 protocol with MAST

34mm dia 3000 mm long- Cold Galvanized

361 SITC of 8 mm dia solid Aluminium Conductor for roof 183.00 Mtr. 299.97

top mesh grid and tested as per IEC 62561-

conducted in the Govt. accredited thirty party

laboratory to meet the requirement of IS/IEC

with Required Accessories - Aluminium Holding clamp

at every 1 mtr distance, Aluminium/SS cross splicer at

every crossing of Alu. conductor, Expansion piece with

connectors at every 20 mtr distance, Aluminium

straight Splicer to connect conductors. All Accessories

should be tested as per IEC 62561-1 2018 Cl. 6.3 for

conditioning & Ageing Test & 6.4 for Lightning

impulse current withstand test: 100 kA of 10/350µs

waveform(Ageing & Electrical test ) conducted in a

sequence manner & tested in the Govt. accredited

Third party laboratory to meet the requirements of

IS/IEC

362 SITC of Galvanized Steel Flat 25x6 mm thickness from 88.00 Mtr. 154.53

earth electrode directly in ground as required. Zinc

coating: 500 g/m square (Approx:70 micron coating)

tested and used exclusively for lightning protection

earthing system and ring equipotential bonding.

363 SITC of 14.2 mm dia 3 mtr long Earth electrode of High 6.00 Per 5992.33

tensile steel electrode with 250 micron copper Set

bonding & 1 bag of Carbon fill Based environment

friendly backfill tested as per IEC 62561-7 in NABL

accredited Laboratory and suitable stainless Steel

double sided clamp. Eco Friendly rust proof heavy duty

weather proof Polyethylene Earth Pit Chamber with

following dimensions :254 mm dia (top), 330 mm dia

(bottom) & 260 mm (height).

364 Supplying, Erecting, Testing & Commissioning the 1.00 Ea. 1235286.56

passenger lift having following main features:

(A) GENERAL DESCRIPTION OF LIFTS.

[1] GEAR LESS LIFT DRIVE (MRL) comprising of High

Starting torque Lift 3 phase 440 V A. C. Permanent

Magnet Synchronous motor of proper rating with high

efficiency shall be used.[2] Micro processor based /

PLC, ACVVVF, vector control drive with encoder

feedback closed loop system shall be used for lift car

and door operation which shall be full collective

UP/DOWN hall stops, Main, Up/ Down Contactor with

overload and phase reversal relay and safety controls.

[3] Car with M S platform with bracings of adequate

size and to sustain the impact load cabin + passenger

with safety factor of fire for steel and side panels of

Stainless steel of sheet of grade 304 duty. Car ceiling

will be S.S. finishes with aesthetic appearance with

LED ceiling lights. Car flooring shall be of s/s

chaker plate design sugeested of engineer in charge. of

engineer in charge. Car doors shall be of stainless steel

grade 304, hairline finish with centre opening /

telescopic automatic doors. Car panel will also be S.S.

304 finished with emergency stop device, mechanical

door safety device, facility of auto/ attended mode. All

car panel buttons and all floor switches must be with

brail language as per lift act.

[4] All landing doors must be fire rated for 2 hour shall

be fully automatic centre opening/ telescopic opening

made of hairline finish steel grade of 304 with key

holes and infrared curtains with Unlocking facility

from outside

[5] Appropriate battery operated emergency light in

the car along with alarm switch shall be provided. Also,

Emergency Light & Fan should start immediately

without any Time Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down

arrow along with floor position indicator shall be

provided inside the car and at all floors.

[7] Full height infra red curtain with multiple cross /

crossing light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided

accordingly of passenger capacity with Manual Rescue

Operation ( Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open till

excess load is removed.

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic

sleep timer shall be provided.

[12] Voice annunciator with suitable music shall be

provided in lift car.

[13] Self diagnostics system for operational and safety

parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and

submission of calibration certificate submission, door

key holes in the floor doors, fireman switch shall be

[15] Lift machine hoisting arrangement in the lift

machine room and monkey ladder for lift pit should be

provided by the lift agency, along with the other steel

structure works, foundations for the machine etc…

[16] In the hoist way fascia plate shall be provided

without any extra cost, where ever required as / if

directed by engineer in charge.

[17] Permanent wiring with necessary safety devices

like RCCB in all circuit, Over Voltage Under Voltage

protection and THD eliminator in circuit for lift

machine room and lift well with proper numbers of

light points, with fixtures, exhaust fan and plug points

shall be provided by the agency. Only 3 phase Power

Supply shall be made available by department in lift

machine room. Necessary Earthing as per Lift

Act/Rules shall be arranged by Lift Agency.

[18] Any civil/ electrical works for additional and

alteration in lift shaft and machine room related to

erection of lift shall be made by lift agency without any

extra cost. (granite/marble fixing around all landing

door openings are not in lift agency’s scope.)

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all

necessary permission from lift inspector and other

authorities. [20] acrylic transparent

licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of Gujarat

lift & escalator act 2000, lift agency has to provide

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after

lift erection and provide report by third party

authorized by concern licensing authority 5.agency

has to provide third party insurance upto completion

of free maintenance period and submit the document

for the same.

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly

visible when view from inside cabin.

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should

be provided at appropriate height on the Rear & Side

Wall Panels in Lift Car. [23] With Necessary KVA

rating voltage controlled Stabilizer suitable for your

controller, drive and all equipments of lift.

[24] Necessary rating of DP Elcb and FP Elcb required

for lift is in scope of work which rating is sugested by

CEICED Department (electrical Inspector)

(B) SPECIAL FEATURES DESCRIPTION OF LIFTS for

PREMIUM category

1. Advanced control system dual 64 bit embedded

microprocessor with CANBUS Serial Communication

mode including Regenerative power efficient

operation,on site programming facility, Anti nuisance,

Pte-opening, BMS/RMS with necessary online real

time monitoring system having necessary connectivity

for remote monitoring & other suitable supporting

hardware & software devices to fulfil the purpose.

2. Floor Indication LCD Display with call registration &

brail mark with arrival gong and hall lantern & TFT

Screen in the car with MP3 Voice Announcer.

3. CAR Panel should be Scratch resistive SS Moonrock

finish / Hair Line / Honeycomb for car and all Doors,

All landing doors must have fire rating up to 2 hours

and car door must have multi-level crisscross beam

door protection.

4. To & fro communication system & wiring (i.e. car

control room & guard room ) and Each elevator are

equipped with remote monitoring system.agency has

to provide mobile app and user id and password for

monitoring

6 Passengers, Ground plus 2 upper floors with Rated

Speed of 1.0 m/sec. (C) With General PLUS

ADDITIONAL SPECIAL FEATURES attached herewith.

Prem. Cat.

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and

words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

1 The Credit Value of Dismentalled Materials of Amount Rs. 6,08,800.00 ( Main Building ) + Rs.97,296.00 (

Compound Wall ) = Rs.7,06,096.00 * shall be recovered from the 1st Running Bill of the Contractor . *(

Refer As per Special Condition atteched in SBD).

2 The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

In-Charge for which no extra payment shall be made.

3 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

4 Income tax TDS will be deducted at a source while making payments of bills

5 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

6 GST will be paid Extra as per Govt. amendment