PROVISION OF CERTAIN REVENUE/MINOR WORKS PHASE I UNDER GE AF TRIVANDRUM

Amount

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete and stacking old materials for issuing under credit all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete and stacking old materials for issuing under credit all as specified and directed.

Supply ,fabricate and install the cantilever roofing system as shown in drawing consisting of 0.50mm Galvalume (Al-Zn) grade 150 GSM with 15cm overlapping of any colour, with horizon profile as shown on drawings. Gutter shall be manufactured out of 3mm thick GI sheet covered by painting by sigma cover 280 epoxy 120 micron and enamel coat with a final rubber coat. Lintel supports shall be 75x75x1.6mm mm thick MS square pipe and MS support from valley gutter to back side of wall shall be done with 50mm dia MS pipe shall be 1.6 mm thick fixed with 15x15x6mm thick Gusset plates to walls by welding / nut and bolt system. Painting on all pipe/gutter shall be done with a cover (280 epoxy 120 micron and enamel coat). The entire roofing sheeting with gutter and lintel and GI pipe shall be provided with sigma cover painting the entire items shall be supplied fabricate and erected in position with structural stability and true plumbing and level fixed by nut and bolt/ welding etc complete all as specified shown on drawings. Make:- Galvalume sheet/ VALLY GUTTER shall be TATA/JSW/ESSAR and MS pipes of square/round pipe Shall be TATA/ZENITH/PRAKASH/JINDAL/SAIL, the contractor can use GI pipe aternatively and before paiting moderant solution shall be applied for efficiant bondage of zigma painting.

Taking down Chowkhats or frames exc. 1.5 sq. m and n exc 4.0 sqm each (without taking off shutters from the frames) and stacking old materials for issuing under credit

M&L for Brickwork with sub- class ‘B’ bricks straight or curved on plan exc 6 m mean radius in CM 1:6, complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and removal of debris out side MD land

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair surfaces of brick masonry or concrete surface, finished the surface even and smooth with using extra cement incl using WPC as per manufacturers instructions, complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for rendering 10mm thick on fair faces of brick or concrete as in backing coat in CM 1:4 complete all as specified.

Supply only liquid waterproofing compound (ISI grade only)

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs/blankets, any thickness, including any type frame work and cover fillets etc, complete and stacking old materials for issuing under credit all as specified and directed

M&L for providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over GI frame work seamless perimeter 0.55 mm thick with two unequal flangesof 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and including hangers 6mm dia G.I (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I flat 40x3 mm mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified.

M&L for preparation of new treated of ceiling surfaces and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

M&L for preparation of new treated of wall surfaces and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and directed.

M&L prepartion of new steel surface of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc crome complete all as specified.

M&L for preparation of new plastered surface of wall and applying two coats of weather coat paint over a coat of primer complete all as specified.

M&L for preparation of new plasreted surfaces and applying two coats of cement base paint over a coat of primer on newly wall surfaces, complete all as specified and directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge.

Supply and fixing factory made uPVC white colour Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-inCharge. (Rate inclusive of frosted Glass pane or PVC sheet whichever is required) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour Two track two panels sliding window above 1.50 m height made of (big series) fram 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 2.50 sqm. upto 4.00 sqm.) comprising of uPVC multichambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I. fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. ( Rate inclusive of Glass or wiremesh) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Rate inclusive of Glass pane and wiremesh). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, complete all as specified and directed.

M & L 18/19mm thick Prelaminated plywood, prelaminated on both sides with decorative choice laminations, fixed with screws to timber frame work as in cupboards, warddrops, kitchen covered cabinet etc including teak wood beading around the plywood/ teakwood lipping shall be finished with two coats of synthetic enamel paint over a coat of pink primer.

S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete member and section details all as speicified in SSR PT 1 2009 and as directed.

M&L for complete removal of existing treatment from wall surfaces, complete all as specified and directed.

M&L for 3mm thick wall care putty on wall surfaces, complete all as specified and directed.

S&F in repairs venetian blind using cotton/Nylon fabric of size as required for windows/ Ventilators horizontally rolling up and down with double layer cloth including rolling device on top and power coated aluminum double layer pipe at bottom, incl operating rope etc all as specified and directed.

S & F in repairs alumimum extruted section body door closer hydraulically regulated, designation No 2, universal type, suitable for door shutters of 801 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil, complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in hard and dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm complete all as specified and directed.

M&L for PCC 1:3:6 type C2, using 40mm graded stone aggregate as in Cement concrete in foundations, filling and mass concrete complete all as specified and directed.

M&L, 100mm thick PCC 1:3:6 type-C-2 in under floor 40mm graded aggregate as in floor subbase, complete all as specified and dircted.

M&L, 75mm thick PCC 1:3:6 type C-2 (using 40mm graded aggregate) as in subbase and floor, complete all as specified and directed.

M&L Pre-cast cement concrete block (PCC 1:3:6, 20 mm graded aggregate) masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete built in CM 1:6 complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer, purlins, crane gantries, rails and fastenings etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, Fe 410 -W (GdeE- 250) quality A, complete all as specified and directed.

M&L for Mangalore pattern Roof and ceiling tiles, inter locking at side joints, laid dry, complete all as specified and directed by Engineer-in-Charge.

M&L Ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and pointed in cement mortar 1:6.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m depth; for doundations, etc, or for shafts, wells, cess pits, manhles, pier holes, etc . Not exceeding 10sqm on plan and getting out in soft/ loose soil

M&L, Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm soft/ loose soil, complete all as specified and dircted.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point, complete all as specified and dircted.

M&L, for laying PCC 1:4:8 (40mm graded aggregate) type D-2 Cement concrete in foundations, filling and mass concrete complete all as specified and directed.

M&L, 100mm thick PCC 1:2:4 type B-2 (using 40mm graded aggregate) as in floor, complete all as specified and directed.

M&L for laterite tile size 300x150x19 mm thick as in wall, set and jointed with adhesive/ chemical and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement over and including 10mm thick in CM 1:4, complete all as specified and directed. Note: Tile shade and design approved by Engr -in-Charge/GE.

M&L for Endura tiles/ stone (coloured/ designer) heavy duty of size 400x400mm, 10-12 mm thick, as in floor, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15mm thick screed bed in CM 1:6, complete all as specified and dircted.

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M&L for 15mm thick screed bed or bedding layer in CM 1:6 for laying floor finishes complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm, Broken stone Broken or boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished with grey cement and pigments complete all as specified and directed.

Supply and fixed No Fuel Incinerator size 64cm x 140cm (Pluto platinum models(SS) (30Kg/day), drum thickness 16 gauge -3mm stainless steel, grate- 47cm dia, exhaust pipe height 14 Feet from the floor (SS 304 grade), rain guard (SS), fire wall (3 inch), complete all as specified and directed by Engr-in-Charge.

M&L for Mild steel bars TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with, complete all as specified and directed.

M&L for Mild steel bars TMT Bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

M&L, for Reinforced cement concrete (design mix) RCC M-30 (using 20 mm graded stone aggregate ) in foundation footing , plinth beams, base of column , under reamed piles and mass concrete, complete all as specified and directed.

M&L Reinforced cement concrete (design mix) M-30 (using 20 mm graded stone aggregate ) Columns, pillars, piers, posts and struts, complete all as specified and directed.

M&L Reinforced cement concrete (design mix) M-30 (using 20 mm graded stone aggregate ) in lintels, Beams, cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed. Note for item No 53 to 55:- Being small quantity of design mix involved, the design mix of on going project for M30 shall be followed however in case of change in sourse of aggregate fresh design mix shall be followed.

M&L, Formwork to Rough finished surfaces of concrete , sides of concrete foundations, footings,bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams ; and similar work with rough finished flat surfaces of concrete, complete all as specified and directed.

M&L, formwork to Rough finished surfaces of concrete , sides of pillars, posts, struts, piers, columns and stanchions rough finished square, rectangular or polygonal surfaces of concrete, complete all as specified.

M&L, Form work to Rough finished surfaces of concrete lintels & roof beam, complete all as specified and directed.

M&L for Glazed ceramic coloured wall cladding tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified.

M&L for modern/ desgin Mural painting exterior or wall tiles for external wall surface set and jointed in neat cement slurry/ adhesive and pointed in white or coloured cement to match, over and including 10mm thick rendering in CM 1:4, complete all as specified and directed. Note: Design and coloured as directed by Engineer-in-Charge/GE.

Surface dressing n exc 15 cm deep in soft/ loose soil, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof overing/ cladding to wall, fixed with self tapping screws as, complete all as specified and directed

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, complete all as specified and directed

Taking down fan, ceiling cable end, fan rod , dismantling cable end , dismantling fan rod all as specified and directed

Supply and fix Ant suicide fan rod ( SMART FAN DOWN ROD ) of length 300 mm (12"), white in colour 19mm OD, 1.8mm +/-0.05mm thick , spring set bgrade 3 carbon steel pipe zinc plated, MSME tested for performance test and opening of impact load of 22 Kgf+ and spring hidden in pipe will expand to about 1 meter or more complete with dafty hole screw all as specified and directed .

All as per item ser No 65 but length 450 mm (18")

Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan ceiling plate, fan canopy , rubber ring shackle, cotter pin and nut- bolts set all as per specified and directed.

M& L for painting of ceiling fan complete with synthetic enamel paint by spraying after cleaning all dust all as specified and directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc all as directed.

M&L for point wiring complete with 1.5 Sqmm single core FRLSH PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through non metallic rigid PVC conduit and accessories in surface of walls/ceilings/ floor including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 1.22 mm thick pressed steel terminal boxes with 3.00 mm thick laminated sheet cover to house switch/regulators etc all as specified and directed.

One fan/light /bell point controlled by one switch/bell push

One switch socket outlet 5 Amps on independent board

All as per Item No 70 here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for power Socket on independent board on the existing/new PVC surface conduit all as directed.

M&L for point wiring complete with 1.5 Sqmm single core FRLSH PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through and including non metallic rigid PVC conduit and accessories concealed in walls/ceilings including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including 2mm Modular metal flush Box and suitable Modular white cover plate with frame and all as specified and directed.

One fan/light /bell point controlled by one switch/bell push

One switch socket outlet 5 Amps on independent board

All as per Item No 72 here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for power Socket on independent board on the existing/new PVC surface conduit all as directed.

Supply and fix modular switch 1 way 6A 1 module

Supply and fix modular socket 6A 2/3 pin combined 2 module

Supply and fix modular socket 6A 2/3 pin combined 2 module including 1.22 mm thick pressed steel terminal boxes with 3.00 mm thick laminated sheet cover to house switch/ socket including connection with existing 5 amps socket points for computer.

Supply and fix modular switch 1way 16 A 1 module

Supply and fix modular socket 6A /16A 2/3 pin combination 3 module

Supply and fix Modular bell push 6 A 1 module

Supply and fix ceiling rose surface Bakelite with three terminals all as directed. Make- Anchor/Havells/Legrand.

Supply and Replace buzzer, AC 230 volts all as specified. Make- Anchor/Havells/Legrand.

Taking down unserviceable sub main wiring and stacking old materials for issuing under credit and M&L for sub main wiring in PVC conduit with two runs of 4 Sq. mm and one run of 4 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLSH grade copper conductor cable single core multistranded drawn through and including 25 mm dia PVC rigid conduit including accessories such as bends, supports etc all as specified

Taking down unserviceable sub main wiring and stacking old materials for issuing under credit and M&L for sub main wiring in PVC conduit with 2 runs of 6 Sq. mm and one run of 6 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLSH grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including PVC conduit of size 25mm dia including accessories such as bends, supports etc all as specified

All as per Item No 83 here-in- before but with 4 Runs 10 Sq. mm and 1 runs of 10 Sqmm earth continuity conductor all as directed

Taking down unserviceable MCB distribution board, and stacking old materials for issuing under credit S & F SPN 8 way of any size and capacity double door with suitable busbar including disconnecting from mains and making good the disturbed surfaces all as directed. Make- Anchor/Havells/Legrand.

S & F SPN 4 way of any size and capacity double door with suitable busbar including disconnecting from mains and making good the disturbed surfaces all as directed. Make- Anchor/Havells/Legrand.

S & F in replacement Sheet Metal Enclosure for VTPN DBs, Triple Pole & Neutral, 4 Way , 415 Volts with 100 Amps rated neutral bus bar double door vertical type, grouting the DB and making good the disturbed surfaces with extra cement without any additional cost suitable for TP/SP outgoing to accommodate and including MCCB 100A 16 KA as incoming all as directed. Make- ABB/Havells/Legrand.

Disconnecting and removing the existing metal plug and socket and stacking old materials for issuing under credit and provn of 25A Mcb Protected Heavy Duty Combined Board with 16A Big Plug, Modular Box for AC,

Taking down and Refixing of serviceable 2'x 2' LED light fitting

Supply and fix MCB 415V,50Hz,AC with rupturing capacity 10KA of the following capacities all as specified and as directed. Make- Anchor/Havells/Legrand.

MCB TPN 32A-40A

MCB TPN 100A

MCB TP 63A

Supply and fix MCB/RCCB 230V,50Hz,AC with rupturing capacity 10kA of the following capacities all as specified and as directed. Make- Havells/Legrand/ABB.

MCB SP 6A - 32A

RCCB SPN 6A -32A 30mA

RCCB SPN 40A 30mA

Supply and fixing round shape 6 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with sensor with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete. Make Crompton Cat No -LCDSPLN-R-06CDL /Philips Cat No- 929002629701/Havells Cat No LHEAABP5IL1W006

S& F Occupancy sensor switch of min 150W - 2 module round shape fixed in ceiling/switch board compete all as specified. Make: Legrand myrius Cat No 679251/ Schneider Cat No CSS54E_WE / Philips LRM1071

Taking power supply shutdown and disconnecting the all connection pump down the refrigerant and carefully shift the indoor and outdoor units of AC/ Split AC in safe place and refix after complete servicing , testing including new insulation materials, topping up gas of existing type and copper pipe all as specified

M&L for submain wiring in PVC conduit with two runs of 2.5 Sq. mm and one run of 2.5 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLSH grade copper conductor cable single core multistranded drawn through and including 25 mm dia PVC rigid conduit including accessories such as bends, supports etc all as specified

Supply and fixing wall light 10 watt 220 volts AC with suitable capacity of bulb fitting on wall including connecting up with three core flexible copper conductor cable of suitable size complete

Supply Ceiling fan 600 mm sweep 230 volts single phase oscillating 450 mm sweep suitable for wall mounting including fitting accessories all as specified

M& L for 3 core 1.0 Sqmm multistranded copper conductor PVC insulated unsheathed cable to connect from junction box to street light fitting drawn through and including rigid non metallic PVC conduit medium grade fixed on pole by means of clamps made out of MS flat irons and connecting from terminal box to light fitting and testing including taking down perished wiring complete all as directed complete all as specified and directed

Supply and fixing Supply of fully vermin & weather proof 50W LED Flood light fitting IP-66 ,made out of aluminium pressure die cast housing toughened glass cover duly powder coated, external driver operating directly on 160V-240V AC, PF:>0.9 complete etc as reqd. Make: Havells Cat No JET QUANTA PLUS MONO 50/Crompton Cat No TFS-504-50-57-NL-SL-GL-NBK or equivalent in Philips

Supply of 2X20W LED Liner wall washer IP-66 made out of Extruded aluminium housing, heat resistant toughened glass , 3000K power LED with lenses , External driver , powder coated finish complete etc as reqd. Make: Luker/Havells/Wipro/Siemens/Philips

Supply and fixing in replacement HOT moulded (FRP) junction box for street light pole with locking arrangement with IP 65 protection of size 140 mm x 140mmx 95mm ( inside dimension) incl 01x MCB 10 Amps SP, 10 KA and two number of PVC cable entry gland of standard size fix in PCC/ wall complete all as directed. Make: Sintex or equivalent in Hansel

S K ENGINEERS

NRI BUILDERS AND MATERIAL SUPPLIERS

mahadeva traders cotractor and suppliers

U K construction

Dhanyaconstructions

ARCHITRAVE CONSTRUCTIONS