Special repairs to building No II-2A at ARO Calicut and Provn of certain civil works at Calicut and Kannur under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing including tilting tiles all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

Dismantling old boarding any description fixed in any position with screws complete all as specified and directed.

Demolition of stone slab and tiles of any description and thickness in floors including cement mortar bedding (but not backing), and rubbish off the premises outside MD land and all as directed.

S&F 100 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank of any capacity all as specified in SSR Part I,2009 and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

M&L for structural steel work in tubular trusses including special shaped washer, two coats of synthetic enamel paint over a coat of primer etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade st-240 all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparing surfaces of wood and wood based materials new of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed

S&F mild steel flat clamp as in supports or stays to PVC rain water gutter fixed with self tapping screws all as directed.

S&F PVC (SWR) half round rain water gutter 150 mm bore including connected fittings ie. Drop outlet, Stop end etc fixed and jointed as per manufacturers instructions complete all as directed.

M&L for preparation of new steel surfaces of any description, not otherwise described exc 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

S & F for anodized aluminium snap grid frame work as in clause No. 10.38 of MES Schedule Part I for false ceiling of size 605 mm x 605mm with supporting hanger comprising of 6 mm MS rod / GI flat 40x3mm, ‘J’ bolt with necessary washers, bolts and nuts for securing frame work to ceiling and to the snap grid complete all as specified and directed

M & L for 4mm thick High Pressure Steam Cured ( HPSC ) non asbestos fibre cement building boards fixed or laid/inserted to aluminium snap grid frame work with screws all as specified and directed.

M&L for preparation of new cement concrete ceiling surfaces or non AC ceiling board surfaces and applying two coats of oil bound distemper over a coat of primer all as specified and directed.

Taking down chowkats with shutters n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

S&F powder coated anodised aluminium frame for doors, windows, ventilators, with one or more rebates including joining cleats for fixing etc, complete all as specified and directed Note:- Thickness of powder coating shall not be less than 50 micron.

S&F anodized aluminium door shutters with aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium snap beading, screws, aluminium fittings such as suitable handles 2 Nos in each door, hinges complete all as specified and directed.

S&F anodized aluminium window and ventilator shutters without sash bars, fixed type with aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable handles 1 Nos in each shutter, complete all as specified and directed.

M&L for coloured glazed ceramic tiles 350x350x7mm or 450x350x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

M&L complete removal of existing treatment on surfaces of wall by scrapping down old treatment, preparing surface even and smooth with a coat of wall care putty and applying two coats of oil emulsion distemper over a coat of primer complete all as specified and as directed

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over a coat of primer all as specified and directed.

M&L for preparation of new decorated wall surfaces (plastered or unplastered) and applying two coats of cement based paint over a coat of cement primer all as specified and directed.

M&L complete removal of existing treatment on surfaces of wall by scrapping down old treatment and applying two coats of cement based paint over a coat of cement primer all as specified and directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F stainless steel butt hinges medium weight; 75mm size all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F 75mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

S&F 3mm thick plain sheet glass, ordinary quality, one side froasted and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

Supply and fix sink with draining board, made out of stainless steel sheet 1mm thick with plugs, washer and waste pipe, including fixing cast iron cantilever brackets and connecting union to pipe over all size 915mm x 460mm with bowl size 410mm x330mmx160mm all as specified and directed.

S&F PTMT towel rail, 600mm long, fixed with and including chromium plated brass screws and wooden/ plastic cleats all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes 15mm/20mm bore all as directed.

S&F for 15 mm bore UPVC (ASTM) pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC (ASTM) pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F stop cock 15mm bore PTMT of any colour, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup fixed in repair complete all as specified and directed

S&F 15 mm bore bib taps, cast copper alloy, chromium plated crutch or butter fly handle, screwed down, screwed for iron pipe or for PVC pipe or for brass ferrule, fixed as in repairs all as specified and directed.

S&F in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

M&L for RCC hume pipe septic tank of 10 users of size as per TD drawing No TD/666 sh 1/1 as in earth work excavation in hard dense soil, PCC 1:4:8 foundation, including vent pipe, inlet-oulet pipes, returning filling and removal of earth etc complete all as per TD drg and directed by Engineer in charge.

Excavating in trenches n.exc. 1.5m wide and n.exc. 1.5m in depth for foundation, etc and n exc 10sqm on plan and getting out in hard/dense soil all as specified and directed.

Returning and filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soil obtained from excavation all as directed

Removing surplus excavated materials (soil) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section ) in cement concrete 1:2:4, type B-1, using 20 mm graded stone aggregate, smooth finished, and reforming benching as required, internal dia of pipe in 160 mm all as specified and directed.

M & L for plain cement concrete (1:4:8), type D2 using 40 mm graded stone aggregate as in foundation, filling, mass concrete etc all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar (1:6) on brick or concrete masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M & L for cement concrete (1:3:6), type C1 (using 20 mm graded stone aggregate) as in benching, stops of manholes, coping etc including weathering, slightly rounded or chamfered angles and throating all as specified and directed.

M&L PVC (SWR) pipe 110mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

M&L PCC (1:3:6) type D2 (using 40mm stone aggregate) concrete bed to drain pipe 160 mm bore including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

M&L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. all as specified and directed.

M&L for precast RCC 1:2:4, type B1, using 20 mm graded stone aggregate as in cover slab (for manholes etc) set in cement mortar 1:6 all as specified and directed.

S&F TMT bars 6 to 8mm dia as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, 10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) and refixing in other opening all as directed.

M&L 20mm thick black Granite (table rubbed and polished) including grounding smooth the exposed edges laid with screed 20mm thick cement mortar (1:6) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified and directed. Note (i) Rate quoted shall deem to include for necessary moulding of sharp edges and screed bed as directed by Engineer-in-Charge.

M&L Reinforced cement concrete (1:2:4), type B1, (using 20mm graded stone aggregate) as in beam, lintel over 1.50m span etc etc all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L for use and waste of form work to sides and soffit of beam, lintel etc rough finished surface of concrete flat all as specified and directed.

M&L for Mild steel TMT bars 5mm dia and over and up to and incl 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.90mm dia or securing with clips all as specified and directed.

M&L preparing new wall surface even and smooth with a coat of wall care putty 1mm thick and applying two coats of acrylic emulsion paint over a coat of primer complete all as specified and as directed

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust outside MD land etc. all as specified and directed.

M&L for coloured joint free non-skid ceramic tiles, 7mm to 8mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 20mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

M&L for mild steel flat iron of size 20 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:3:6, type C1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works all as specified and directed.

M&L for pre laminated particle board, 18mm thick interior grade, pre laminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to wooden framework all as specified and directed.

S&F extruded aluminum alloy anodized handle fabricated type 75mm size all as specified.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C2 using 40mm graded stone aggregate as in sub base for floors all as specified and directed.

M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and no pigment all as specified.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate as in coping, lintel band, string coarses etc slightly rounded and chamferred angles and throating etc including necessary form works and finishing all exposed surfaces of concrete all as specified and directed.

Taking down shutters exc. 1 Sqm but n.exc 2 Sqm each easing and adjusting, renewal of builders hardware and refixing in same opening all as directed. Note: Builders hardware shall be measured and paid seperately.

Supply only stainless steel butt hinges medium weight; 100mm size all as specified.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc. all as directed

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit concealed to wall and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

All as per item No 84 here in before but for One 3 Pin, 5 Amps socket on same board with other switches all as specified and directed.

All as per item No 84 here in before but for One 3 Pin, 5 Amps switch socket combination on independent board all as specified and directed.

All as per item No. 84 on here in before but for one 3 pin 15 amp switch socket combination on independent board with 2.5Sqmm unsheathed PVC insulated copper conductor FRLS cable including 2.5 Sqmm PVC insulated copper cable for earth continuity conductor complete all as specified.

Cutting chases on wall of width 30mm and depth 35mm for concealing PVC conduit 20/25mm dia and making good the surface with plastering in cement mortar 1:4 and finish to match the existing surface and treated with existing treatment such as white wash/OBD/cement base paint etc complete all as directed.

All as per item No 88 here in before but width 50mm all as directed.

S & F modular type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F modular type, single pole, one way, 16 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose round shape, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S&F modular socket, 2-in-1, 5 pin, 6 amp, 240V, connecting up electrically all as specified and directed.

S&F modular socket, 2-in-1, 5 pin, 6&16 amp, 240V, connecting up electrically all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for two module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for three module all as specified and directed.

S&F modular type metal box including white modular cover plates with frame for six module all as specified and directed.

S & F sheet metal enclosure factory made for MCB DB, SPN 4 way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up complete all as specified and directed.

S & F MCB SPN, 240 Volt, 32Amps including electrically connecting up using wiring lugs all as specified and directed.

S & F MCB SP, 240 Volt, 6 to 32Amps including electrically connecting up using wiring lugs all as specified and directed.

Taking down unserviceable fluorescent tube light fittings, S & F Decorative ultra slim linear LED light fittings with extruded AI, heat sink, environmental friendly, energy efficient ready to use pack of E-LITE LED of 20 W LED 6000K, model LHEWEBP7IN1W020 of Havells or equivalent of PHILIPS of Crompton Greaves, with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

Taking down unserviceable bulk head fittings from wall, Supply and fixing LED street light fittings of 30 watts on wall/pole of height 3 to 5M of energy saving and environmental friendly long life made up of pressure die cast aluminium housing with high power LEDs as lighting source and lense embedded PC cover having IP 65 protection of model No SL30WLED757SASYBOPC of HAVELLS or equivalant of CG or Philips including suitable type GI bracket, clamps etc and electrically connecting up all as directed.

S&F lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings nd electrically connecting up all as directed.

S&F in repalacement LED ball type lamp 10watt all as directed.

M&L for sub main wiring with two runs of single core 4 Sq mm copper conductor FRLS cable, PVC insulated, unsheathed multistanded, 1100 V grade drawn through and including non metallic rigid PVC all accessories such as bend,elbow,socket,tee saddles etc fixed concealed to wall / fixed to ceiling etc including 4 Sq mm single core copper conductor FRLS cable PVC insulated, unsheathed multistranded 1100 V grade as earth continuity conductor connected to common earth dolly complete all as specified and directed. Note :- 3 runs of 4 Sq mm copper cable and one run of PVC conduit will be measured as one length.

M&L for pre laminated particle board, 12mm thick interior grade, pre laminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to wooden framework all as specified and directed.

Supply and fixing in repair exhaust fan, plastic body suitable for 250 mm dia sweep complete with fixing accessories including making hole as per site requirement for suitable size all as specified and directed. Make Cat part No FHVVEDXOWH08 of Havells or equivalent in CG/Philips.

VIJAY ENTERPRISES

ANAND REFRIGERATION