PROVISION OF YOGA CENTRE AT CIVILLIAN DEFENCE COLONY (SAGAR) GARHI CANTT, PARKING SHED AT 14 LEADING QUARTER AND ADDITION/ ALTERATION OF CONFERENCE HALL IN BLDG NO. P-41 AT NHO, DEHRADUN

Amount

Surface excavation n.exc 30cm deep avg 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc. Or for shafts, wells, cesspits, manhole, pierholes etc n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed

Returning filling in soil incl spreading, levelling, watering and well ramming in layers n ex25 cm

Removing excavated soil n exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point

M&L for treating the bottom and sides of excavation at the rate of 5 ltrs of emulsion per sqm complete all as specified and directed

M&L for treating the backfill in contact with foundation @ 7.5 ltrs of emulsion per sqm of vertial surface (area of sub structure in contat with backfill to be measured)complete all as specified and directed

M&L for treating the top surface of filled earth @ 5 ltrs of emulsion per sqm complete all as specified and directed

M&L for treating the soil under plinth protection @ 5 ltrs of emulsion per sqm of surface area complete all as specified and directed

M&L for treating the soil alongwith external perimeter of building @ 2.25 ltrs of emulsion per meter of perimeter wall complete all as specified and directed

M&L for cement concrete type D2 1:4:8 (40 mm graded agg) as in foundation filling and mass concrete complete all as specified and directed

M&L for reinforced cement concrete Design Mix M-25 (20 mm graded agg) as in foundation including rafts, footings, foundation beams, bases of columns etc and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete Design Mix M-25 (20 mm graded agg) as in columns, pillers, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete Design Mix M-25 (20 mm graded agg) as in beams, cantilevers, lintels, chajjas complete all as specified and directed.

M&L for reinforced cement concrete M-25 (20 mm graded agg) as in slabs supported on walls, beams and columns in floors, roofs, landingand the like complete all as specified and directed.

M&L for form work to rough finished surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beamssides and soffits of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

M&L for form work to rough finished surfaces of concrete soffits of suspended slab such as roof slabs, floor slabs and similar work n exc 200 mm thick (horizontal or sloping) complete all as specified and directed.

M&L for form work to rough finished surfaces of concrete of sides and soffits of floor or roof beams, lintels etc and similar work complete all as specified and directed.

M&l for Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and ditrected

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide

M&L for mild steel TMT bars 10 m dia and over , cut to length bent to shape required incl necessary cranking, bending spirally for hooping ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed

All as per item No.20 above but 6 to 8 m dia

All as per item No.20 above but 5 mm dia and over upto and incl 10 mm dia in stirrups, spacers and binders

M&L for brick work with old size sub class 'B' bricks , straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as specified and directed

M&L for brick work with old size sub class 'B' bricks , straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed

M&L for rendering 15 mm thick in CM (1:6) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on concrete surface of ceiling in CM 1:4 complete all as specified and directed.

M&L for rendering 15 mm thick in CM (1:4) miixed with and incl liquid water proofing compound as per manufacturer instructions on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n exc 63 mm , deposited , spread and levelled in layers n exc 15 cm thick , watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick cement concrete type D2 1:4:8 (40 mm graded agg) as in sub base to floor complete all as specified and directed

75mm thick PCC 1:2:4 Type B-1 using 20mm graded crushed stone aggregate as in floor/path complete all as specified and as directed.

M&L Vitrified coloured tiles 8-10mm thick any Shade/Double charged (square/rectangular) area of each tiles exc 0.18 Sqm but not exc 0.42 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed of cement mortar 1:6 laying floor finishes, complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick Dark Shade/Double charged (square/rectangular) area of each tiles exc 0.18 Sqm but not exc 0.42 Sqm as in vertical surface such as dado/ skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 to recieve tiles complete all as specified and directed by Engr-in-Charge.

M&L for non skid coloured ceremic tiles 7 to 8 m thick (square/ rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceremic tiles in vertical surface 450x300x7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4

M&L for providing 75 mm thick cement concrete 1:3:6, type C-2 (40 mm graded agg) as in plinth protection incl joints filled with bitumen mastic comlete all as specified and directed.

S&F in repair powder coated aluminium glazed side hung double door shutters with anodised aluminium frame of section 100x44x1.5mm and shutter having style, top rail, lock rail and bottom rail of 84x44x1.5mm including 5.5mm thick tinted blind sheet glass ordinary quality with all necessary suitable push & pull plate/handle, screw, jointing cleats, rubber packing, aluminium snap beading and 1 No 200mm long Al tower bolt, 100 mm long 3 No Al butt hinges B-21 type, and one No mortice brass lock 100mm size 4 leaver (vertical type) complete all as specified and directed by Engr-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (50mm x 100mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick Moulded WPC Brown Factory made 100% Solid door both side laminated (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F of 100mm long stainless steel butt hinges, medium weight complete all as specified and directed by Engr-in-Charge.

S&F 150mm long, Stainless Steel barrel tower bolts complete all as specified and directed by Engr-in-Charge.

S&F 150mm size Stainless Steel handles, all as directed complete all as specified and directed by Engr-in-Charge.

S&F anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and directed.

S&F anodised aluminium powder coated window and ventilators shutters , fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading , screws etc complete all as specified and directed

M&L for Granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement lurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 15 mm thick screed bed in CM (1:6) complete

M&L for rounding to edges of stone slabs one edge, such as in steps, window cill, cooking platform and other similar situations

S&F sheet glass 4 mm thick ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane complete

S&F figured glass pin headed type 4.0 mm thick glazing with oil putty in squares n exc 0.5 sqm in each pane

S&F water closet vitreous china squatting pan 'Orissa' pattern size 580x440 mm white with integral foot rest (excl flusing cistern and flush pipe)complete incl provision of lime concrete & connection to trap incl trap

S&F PVC valve less , syphonic action type , flushing cistern 10 ltrs capacity, low level, white with inlet , ball valve, float and handle incl brackets complete all as specified and directed

S&F Vitreous China wash down water closet pan (pedestal pattern), white incl seat cover with P or S type trap complete

S&F vitreous china wash basin white flat back size 550x400mm incl 01 No. CP pillar tap fancy type 15 mm, CP waste coupling 32 mm , PVC waste pipe 750 mm long and brackets incl cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed

S&F tubes "Med grade' galvanised 15 mm bore with all fittings and fixed to walls and ceiling or laid in floors incl concealed in walls complete all as specified and directed.

All as per item No.52 above but 20 mm bore

S&F Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore of pipe complete.

S&F Stop valves/ angle cock, cast copper alloy fancy type chromium plated 15 mm bore, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Chromium plated health faucet with connection pipe 1 m long complete all as specified and directed

S&F 20 mm bore gun metal globe gate valve with iron wheel head screwed both ends for iron pipe and fixed complete

S&F 20 mm bore ball valve high pressure of PTMT epoxy coated aluminium rod and high density plastic ball screwed for iron pipe anf fixed complete.

S&F PVC connection 15 mm size of length 450 mm

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints , laid in floors or in trenches or to walls complete

S&F PVC (SWR) bends of 110 mm bore of any radius

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints , laid in floors or in trenches or to walls complete

S&F PVC (SWR) bends of 75 mm bore of any radius complete all as specified and directed

S&F PVC (SWR)floor trap plain with grating incl jointing solvent of 75 mm bore complete all as specified and directed

S&F rortational moulded polythene water storage tanks 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified an directed.

M&L for preparation of newly plastered surfaces and finishing walls with acrylic smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/ 10 sqm over and incl priming coat of primer of exterior primer applied @2.20 kg/10 sqm) complete all as specified an directed.

M&L for coloured Machine pressed precast polished glossy finish concrete interlocking paver block as in road berm, path and hardstanding any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade with pigments over and including 25mm thick sand cushioning complete all as specified and directed by Engr-in-Charge.

M&L of water proofing treatment to non-accessible roof slab with APP based modified polymeric membrane as per manufacturer's instructions with following course of description below :- (i) Applying a priming one coat of bituminious primer evenly @ 0.30 Kg/Sqm till the surface is properly impregnated. (ii) Providing APP based 5 layer polymeric membrane minimum weighting 3.60 Kg/Sqm and minmum 3mm thick reinforced with polyester non-woven fabric matt (weight not less than 150 gms/Sqm) centre core laid on primed surface by forced applications as per the manufacturer's instructions with side over lap of 75mm and end overlap of 100mm. All overlap joints shall be sealed thoroughly by thermo fusing both the membrane layer (torching overlap by propane or butane gas torch) and sealing it with the help of hot trowel. The overlap joints shall be made as a monolithic layer. (iii) Apply two coat of bituminous aluminium pain @ 0.20 Kg/Sqm over APP Membrance. (Note: the work in respect of water proofing treatment shall be carried out only by authorized/approved applicator of the manufacturer/firms of app membrane. The contractor shall submitted 10 year company back warranty before claiming payments complete all as specified and directed.

M&L for RCC pipes, class NP3, laid in trenches & jointed as specfified for 200 mm bore of pipe including collars complete all as specifed and directed.

M&L for concrete bed in PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.), shelves and similar articles with plain faces including necessary form work, set in cement mortar 1:4 complete all as specified and directed. (Note:- Reinforcement shall be measured and paid for separately under respective item of schedule 'A').

M&L for cutting into existing manholes for connecting new drains 225mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete al as specified and directed.

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone agg ) as in surface channel and drains complete all as specified & directed.

M &L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms moulds mitered/stopped in etc complete all as specified and directed .

S&F SS 304 Grade curtain rod 25 mm dia with brackets and end doms complete all as specified and directed.

Excavation over areas n exc 1.5 m deep and getting out any type of soil complete all as specified and directed.

M&L for fair finished surfaces of formwork to faces of walls, retaining walls, abutments, parapets and stair case railings and similar work incl attached pillasters buttresses, etc vertical or to batter complete all as specified and directed.

M&L for providing reinforced cement concrete M-25 (design Mix) (20 mm graded aggregate) as in walls , retaining walls, and the like any thickness, above top of footings; incl attached pilasters and buttresses complete all as specified and directed.

Supply and filling graded coarse aggregate of 40 mm as in filter media at weep holes of retaining walls complete all as specified and directed.

Dismantling wall & ceiling boards (fibre, insulation etc ) or insulation boards, slabs, blankets any thick ness including cover fillets complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work and barbed wire fixed in any position of any description not other wise specifically provided for

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed by Engr-in-Charge.

M&L Removing old paint by paint removers or burning off by blow lamps and cleaning with scrapers , any number of coats, any width or girth.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base/ levelling course of floor complete all as specified and directed by Engr-in-Charge.

M&L 100mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any shade (Square/Rectangular) double charged area of each tiles n. exc 0.36 sqm over and including 15mm thick screed bed in cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any shade (Square/Rectangular) double charged area of each tiles n. exc 0.36 sqm , as in skirting/dado, over and including 10mm thick rendering in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L Non skid Ceramic tiles (Mat Finish) 7-8 mm thick (rectangle) area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors over and including 15mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge

M&L for 18-20mm thick granite (of any type) work (table rubbed and polished) stone slab as in steps, jambs, pillars, window-cills, cooking platforms and like set in and incl.15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade complete all as specified and directed by Engr-in-Charge.

M&L preparation of new plastered surfaces with 1mm thick wall care putty and applying two coat of acrylic distemper over a coat of primer on walls complete all as specified and directed by Engr-in-Charge.

M&L 1st Class Hardwood 40mm thick Plain,Framed, Half Panelled, Half Glazed shutters(any number of panels), with panels of timber flat on both sides(feather edged), or of veenered particle board medium density, wood particle board with decorative face veeners:suppied and fitted to chowkhats complete all as specified and directed by Engr-in-Charge.

S&F of 100mm long Stainless steel butt hinges, medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

S&F 150mm long, Stainless Steel barrel tower bolts complete all as specified and directed by Engr-in-Charge.

S&F 150mm size Stainless Steel handles, all as directed complete all as specified and directed by Engr-in-Charge.

S&F of 250mm long (Length of bolt) Stainless Steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, and fixing bolts and sliding bolt complete all as specified and directed by Engr-in-Charge.

M&L French polishing on wooden surfaces of any description,width or girth incl cleaning and preparing the surface including a coat od wood filler on new works with two or more coats complete all as specified and directed.

S&F 12mm thick ply with decorative veneer as in wall panel and fixed over & including 2nd class hard wood, wooden scantling (area exc 6 sqm but n.exc 13 sqm) in grid of size 600mm X 600mm. Decorative ply shall be finished with French polish (any number of coat including preparation of surface) complete all as specified and directed.

S&F false ceiling with Semi perforated 10mm thick Square edged GRG False Ceiling tiles at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595 x 595mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Nomocombustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120grams per Sqm incliuding both sides) comprising of main-T runners of size 15x32mm of length 3000mm, cross-T of size 15x32mm of length 1200mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per Sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod up to 2000 to mm length and L-shape level adjuster os size 85x25x2mm. Galvanized iron perimeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall/ partition with the help of plastic rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engr-in-Charge.

S&F 4mm thick frosted glass with NHO & Navy logo frosted on glass. Incl fixing to wooden shutter with suitable wooden beading complete all as specified and directed.

Excavation in post hole (or similar holes) each n. exc 0.5 cum, getting out, returning filling in any type of soil and ramming earth or broken rubble mixed with earth around in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface in any type of soil complete all as specified and directed

S&F Mild steel in joist, channel, angle, tubular poles, tubular sections fixed independently, conforming to Fe-410W(Gde-E-250) quality-B complete.

S&F mild steel work as in trusses, rafters, purlins etc, and the like made out of MS pipe, flat, angle or hollow sections conforming to Fe-410-W (Gde-E-250) quality-A incl all necessary cleats, gusset plates etc complete all as specified and as directed.

S&F Mild Steel Plates(plain or chequered) channels, square cut or notched (ordinary or counter sunk) forming holes, without any attachment conforming to Fe 410W(Gde-E-250) quality-A complete all as specified and as directed.

M&L for cement concrete 1:3:6 type C1 (Using 20mm graded stone aggregate ) as in foundation of posts, railing and similar work complete all as specified and directed by Engr-in-Charge

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick(AZ-150) of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based plain steel sheet 0.50mm thick (AZ-150) of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and directed

M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

M&L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade(Company depot Tinted) with silicon additives @1.43 litre/10sqm over and incl priming coat of exterior primer [email protected] litre/10 sqm over new surfaces complete all as specified and directed.

Surface dressing not exceeding 15 cm deep and getting out any type of soil complete all as specified and directed by Engr-in-Charge.

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed by Engineer-in-charge.

M&L for Providing, cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) as in coping including formwork (straight or curved), ends of interlocking and finishing Complete all as specified and as directed by Engr-in-charge.

M&L for 40mm thick cement concrete type B-0(12.5mm graded aggregate) as in Damp Proof Course horizontal or vertical surfaces incl WPC @2% incl necessary formwork complete all as specified and directed by Engr-in-Charge.

M&L treating the back fill with ATT in contract with foundation @7.50 ltrs of emulsion per sqm of vertical surface complete all as specified and directed.

M&L treating the top surface of filled earth with ATT @ 5 ltrs of emulsion per sqm complete all as specified and directed.

M&L treating the soil under plinth protection with ATT @ 5 ltrs of emulsion per sqm complete all as specified and directed.

M&L treating the soil alongwith external perimeter of bldg with ATT @ 2.25 ltrs of emulsion per RM complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No 121 above but with 4.0 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing switch modular , one-way 16Amps, 1 module 240 Volts AC all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz all as specified and directed by Engr- in-charge.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz all as specified and directed by Engr- in-charge.

Supply and fixing bell push modular flush type single pole one way 6 Amps, 1 module all as specified and directed by Engr- in-charge.

S&F Bell ding dong Type , 240 Volts complete all as specified and directed.

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals ISI marked all as specified

Supply and fixing step socket type modular fan regulator 120/280 V , 2 module all as specified.

Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittings all as specified & directed.

S& F wall mounted LEDTube light fitting 1 x 20 watt,4 feet with & including LED lamp complete all specified and directed .

S& F wall mounted LEDTube light fitting 1 x 10 watt,2 feet with & including LED lamp complete all specified and directed .

S & F ceiling fan BLDC Type1200 sweep 240 volts Ac 50 Hz complete all as directed.

S & F PVC fresh air fan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as directed.

Supply and fixing LED building security light 1X30 W housing made out of pressure die-cast aluminium alloy with toughened glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.98 having over voltage protection up to 440 volts, Surge protection level ≥ 10 KV, thermal short circuit protection THD < 10% made up of long life LED chips (SMD) in modular with Ra>70, and LED lumen efficiency >140 lumen per watt, beam angle along the drive way, 120 degree, beam angle across the drive way, 80 degree luminior efficiency > 130 Lumens/watt, power LED should be of more than 01 watt CCT should be between 5700° K- 6500° K including fixed on wall with 02 Nos MS clamp made out of 40X6 mm FI and bracket made out of 32 mm dia light grade GI pipe not less than 0.90 mtr long bend to shape complete all as Specified and directed including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from terminal box to light fittings complete all as specified and as directed by Engr-in-Charge (i) the firm has to give warranty for street light fittings including driver minimum for 03 years for any defects developed during the period. (ii) The contractor shall submit the third party LM 79 report from any NABL approved laboratory. (iii) The fitting should have BIS, CRS no.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 12 way with 200 Amps rated bus bar all as specified and directed .

Supply and fixing MCB SP 5 to 32 Amp 'B' series 10 KA repturing capacity complete all as specified.

Supply and fixing MCB SPN 40 Amp 240 V AC 10 KA repturing capacity complete all as specified.

Supply and fixing in repair sub main wiring two single core 4 sq mm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and as directed. Note:- Two runs of multi stranded copper conductor cable and one run of earth wire including PVC conduit will be measured as a one length.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

All as per item No.144 above but with 2.5 Sqmm PVC insulated FRLS cable for 15 Amps power point,modular type switch complete all specified and directed .

S&F only round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S& Fled luminaire 600mm x 600mm,35/36 watt,220 v AC recessed / surface type with high efficiency PMMa diffuser soft glare free light complete with driver ,holders and LED lamp suitable for roof ceiling incuding connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fixing in repair sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated busbar all as specified and directed .

Supply and fixing in repair sheet metal enclosure single door type for MCBs DB TPN(Tripal pole and neutral) 240V AC 4 way with 200 Amps rated busbar all as specified and directed .

Supply and fixing Vertical type TPN DB, 4 way ( DPX 125+12), as per IS 8623, IP - 43 protection, universal mounting with 200A Copper bus bar with neutral bar, earth bar and cable ties for cable management, top and bottom removable gland plate suitable for MCCB 125 Amps as incomer and SP MCBs 12 Nos & making necessary electrical connection for incoming and outgoing cables, with copper lugs complete all as specified and directed

Supply and fixing MCCB 160 Amp, TPN, 415 volts, ultimate breaking capacity (ICU) - 36 KA, confirm to ICU 100 % ICS

Supply and fixing in repair MCB SPN 32 to 63Amp 'B' series 10 KA repturing capacity complete all as specified.

Supply and fixing in repair MCB SP 6 to 63 Amp Amp 240 V AC 10 KA repturing capacity all as specified.

M&L in repair sub main wiring two single core 6 sq mm PVC insulated unsheathed stranded copper conductor cable ( FRLSH) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade cassig caping / concealed in wall along with 6.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion all as specified and directed.

M & L PVC trunking profile of size 30mm x 35mm for any type of wiring / cable,complete with all accessories like fiexible cover ,end caps cable tie base ,angles,junctionsetc & all fitting matetials required as per site , complete all as specified and directed.

M&L sand cushioning 8cm below and 15cm above the U/G cable for protection of cable with approved sand.

Supply & laying fly ash bricks in layers perpendicular to the axis of U/G cable for protection of cable complete all as specified and directed.

Supply and laying PVC insulated armoured heavy duty elect cable with STRANDED aluminium conductor 1100 V grade, cross sec area 10sqmm 2 core and connected with aluminium lugs,& properly crimped in trenches/duct/fix on pole complete all as specified and directed.

Supply and install commis - sioning of water cooler partially stainless steel ,electric driven single phase having approx storage and nominal cooling capacity 40/80 Ltrs complete all as specified

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

ANANYA CONSTRUCTION CO. (BID ID -3483744)

M/S C S AITHANI (BID ID -3484248)