Upgradation of Secondary School building at district PORBANDAR.

Excavation for foundation upto 1.5 m depth including sorting out and

stacking of useful materials and disposing off the excavated stuff upto

50 Meter lead.(A)

Loose or soft soil

Filling with the available excavated earth (excluding rock) in

trenches, plinth, sides of foundation etc. in layers not exceeding 20cm

in depth consolidating each deposited layer by ramming and

Filling foundation and plinth with murrum or selected soil in layers

8 of 20 cm. thickness inculding watering, ramming and consolidation 1710.76 307.41 Cmt.

White stone Bela mesonary block in course in foundation and plinth

9 with stone of approved quality in cement mortar 1:6 (1 Cement :6 166.45 6228.87 Cmt.

fine sand) including curing etc. complete

White stone Bela mesonary block in course in superstructure with

10 stone of approved quality in cement mortar 1:6 (1 Cement :6 fine 92.47 6524.01 Cmt.

sand) including curing etc. complete.For all heights and all floors.

Providing & laying Cement Concrete 1:4:8 (1 Cement :4 Coarse sand

:8 hand brocken stone aggregates of 40mm nominal size) in plinth

and curing complete including cost of formwork. (A) Foundation and

Plinth - At plinth level

Providing and laying cement concrete 1:5:10 (1- Cement : 5- Coarse

sand : 10- hand broken stone aggregates 40 mm nominal size) and

curing complete including cost of formwork in (A) Foundation and

Providing & laying Cement Concrete 1:2:4 (1 Cement : 2 Coarse

Sand : 4 graded stone aggregate 20 mm nominal size) & curing

complete including cost of form work (A) Foundation and Plinth -

Below Tie beam, Plinth protection & surface leveling work.

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-

coarse sand : 4-graded stone aggregate 20mm nominal size) laid in

one layer and finished with a floating coat of neat cement. (A) 40mm

Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in (C) Coping Vertical

and horizontal for all floor (Cement Level 360 Kg)

Providing and laying controlled cement concrete M.250 and curing

complete including the cost of formwork and Excluding the cost of

reinforcement for reinforced concrete work in (A) Foundations,

footings, Base of columns and Mass concrete.(Cement Level 380 Kg)

Providing and laying controlled cement concrete M.200 and curing

complete including the cost of formwork and excluding the cost of

reinforcement for reinforced concrete work in (C) Slab all floor

(Cement Level 360 Kg)

Providing I.S.I. T.M.T Bars Fe.500D steel reinfocement (ISI mark)

18 Confirmed to IS-1786 for R.C.C.work including Cutting, bending, 895.10 77.29 Smt.

binding and placing in position etc. complete.For all floors

Description Of Item Quantity Rate Unit Amount

Providing 10mm thick cement plaster in single coat on on

brick/concrete walls & Ceilling & Soffit of stair interior plastering in

cement mortar 1:4(1 cement 4 sand) watering, curing etc.

complete.For all floors

Providing 15mm thick cement plaster in single coat on rough or fair

side of single or half brick wall for interior plastering in cement

mortar 1:4(1 cement 4 sand) watering, curing etc. complete.For all

20mm thick sand faced cement plaster on walls above ground level

consisting of 12mm thick backing coat of cement mortar 1:3(1

cement 3 sand) and 8mm thick finishing coat of cement mortar 1:1(1

cement 1 sand) watering, curing etc.complete for any Height.

Finishing wall with weather proof exterior emulsion paint on wall

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, and remains of

loose powdered materials.etc complete. The rate shall be including of

providing two coats of primer of approved brand and manufacturer

on new wall surfaces to give and even shade including throughly

brushing the surface free from mortar dropping and other foreign

matter and sand papered smooth.

Distempering with dry distemper of approved brand and manufacture

(two coats) and of required shade on wall surfaces to give an even

shade, over and including applying one coats of Birla (White Cement

23 based) or Asian (acrylic lapy) or equivalent and a priming coat of 11719.41 94.32 Smt.

whiting after thoroughly brooming the surface free from mortar

dropping and other foreign matter and sand paper smooth. The rate

shall be including scraping and old deteriorated of existing paint.

Painting two coats (excluding priming coat) on new wood and

wood based surface with ready mixed paint, brushing, oil,

24 gloss, semi gloss to give and even shade including cleaning of 421.73 112.30 Smt.

all dust, dirt and other foreign matter sand papering and

Painting two coats (excluding priming coat) on new steel

and other metal surface with synthetic enamel paint,

brushing to give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

Providing and laying 25mm thick polished Kota stone

flooring/staircase treads (two pieces with three groves in front of

26 steps) over 20mm (average) thcik base of cement mortar 1:6 (1 1961.34 1019.39 Smt.

cement 6 coarse sand) laid over and jointed with grey cement slurry

including curing, rubbing, and polishing etc. complete.

Re-fixing of existing 25mm thick polished Kota stone

flooring/staircase treads over 20mm (average) thcik base of cement

27 mortar 1:6 (1 cement 6 coarse sand) laid over and jointed with grey 202.20 714.89 Smt.

cement slurry including curing, rubbing, and polishing etc. complete.

(As directed by Engineer in charge)

Providing & fixing average 25mm thick Double polished Kota stones

28 for shelves in cup board, seating plat form, including curing, rubbing, 64.00 815.10 Smt.

polishing etc. complete. (As directed by Engineer in charge)

Providing & Fixing 25mm thick double polished vertical Kotah stone

29 for (partion)urinal as par drawing including round edge moulding etc 4.32 1361.60 Smt.

comp. (As directed by Engineer in charge)

Providing and laying 18 mm thick mirror polished black granite stone

machine cut in single piece (Max. available) in sill and jambs laid

over 10 mm thick cemen mortar 1 : 3 (1 cement : 3 coarse sand) and

30 jointed with grey cement slurry with matching pigment incl. rubbing 91.13 2061.46 Smt.

and polishing half rounding edge both side etc. complete colour and

shed as approved by architect engineer in charge. (As directed by

Engineer in charge)

Description Of Item Quantity Rate Unit Amount

Providing & Laying Broken China Mosaic flooring for plain & curve

surface 12mm to 20mm of broken piece of ceramic tiles or Glazed

tiles ( one or more colour as directed by Engg. In charge ) to be laid

over cement mortar bedding of CM 1:3 to plain or and slopes and to

31 be tempered to bring mortar cream up to and colour pigment 2537.17 779.70 Rmt

including rounding of junctions and extending them pu to 15cms

along the wall and curing with bends any patterns of designs as per

deawing or directions including cleaning with water and oxilic acid

using 1 kg / 1 bag of water proofing materials.

Providing cement vata (10 cm X 10 cm size) quartar round in cement

mortar 1:1 including neat cement finishing, watering etc. complete

Respectely plaster acitivity shall be commenced only after completion

Providing & fixing in position mild steel door with ventilation frame

40x40x6 mm and shutter frame 35x35x5mm ,75x5 mm ms flate at

lock rail,10 mm square bar in vent at10 cm c/c coverd with

33 corrugated ms sheet 0.6 mm thick, including applying a priming coat 12.90 3718.05 Smt.

of read lead paint including cleanicn the surface of all dirt, dust and

other foreign matter (As directed by Engineer in charge& approved

drawing and design etc.)

Providing & fixing in position mild steel window with ventilation

frame 35x35x5 mm and shutter frame 25x25x5mm ,10 mm square

bar grill at10 cm c/c coverd with corrugated ms sheet 0.6 mm

thick,including applying a priming coat of read lead paint including

cleanicn the surface of all dirt, dust and other foreign matter (As

directed by Engineer in charge& approved drawing and design etc.)

Providing and fixing FRP frame size 100x50 mm and 28mm thick

FRP depress panel shutter having extra reinforcement on sides &

edges in Gel coat finish. The core of the shutter & frame is to be filed

up with injected fire retardant grade polyurethene foam done in situ

35 alongwith embedded wooden pieces for stiffening & also taking 44.00 2377.76 Smt.

hinges & fintures. The whole FRP frame & shutter is to be water

proof weather proof, termite proof & resistance to mild acid/alkali.

Rates are to be inclusive of S.S hinges with necessary screws &

alluminium fixtures & fastenings & fastener sleeve.

Providing and fixing window having extruded aluminum Colour

Powder Coated section frame main outer size 63.50 x 38.10 x

mm(of Jindal Section no:4605,@ Wt 1.094 Kg / Rmt), horizontal two

track member size 61.85 mm x 31.75 mm x 1.20mm (of Jindal

Section no: 8687 @ wt.of 0.695 Kg/mt), vertical member of size

61.85 mm x 31.75mm x 1.30 mm (of Jindal Section no:8758 @ wt.of

36 0.0.659 Kg/mt) with sliding shutters of horizontal member size 40mm 0.72 1713.70 Kg.

x 18mm x 1.29mm (of Jindal Section no:8949 @ wt.of 0.456Kg/mt),

vertical member of size 40mm x 18mm x 1.29mm (of Jindal Section

no:8947 @ wt.of 0.456Kg/mt/ Section 8948, @ Wt. 0.457 Kg/mt)

with 5 mm thick transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures and transparent silicon

sealant glass fixing to frame as per details etc complete for window.

Steel work, M.S Grill, welded in built up sections framed work

including cutting, hoisting, fixing in position and applying a priming

coat of read lead paint. (A)In beams and joists, channels angles Tees,

flats, with connecting plates or angle cleats as in main and cross

beams. Hip and jack rafters, purlins conneted to common rafters and

Providing & fixing G.I rain water Spout of 65mm dia and 60cm

Painting of logo on front side wall as directed by Engineer in charge

and as per approved drawing.

Providing and laying white glazed tiles 6mm thick in flooring treads

of steps and landing laid on a bed of 12mm thick cement mortar 1:3

(1-cement : 3-coarse sand ) finishing with flush pointing in white

Providing and laying white glazed tiles 6mm thick in skirting, riser of

41 steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3 374.62 1127.48 Rmt

coarse sand) and jointed with white cement slurry.

Description Of Item Quantity Rate Unit Amount

Providing and fixing Chicken mesh jali (22 gauge) 15cm wide at the

junction of 2 different surfaces of different material component at the

time of plastering to prevent cracking in plaster surface as and where

directed at all floors with all leads and lifts etc.complete.

Providing & Fixing Green board(2400mm x 1200mm) with soft

43 board(1200mm x 1200mm) on wall as per the drawing & design etc. 30.00 10352.50 Smt.

Providing upto floor two level precast cement concrete jali or grill

1:2:4 mix (1- Cement : 2- coarse sand : 4-graded stone aggregate

44 6mm nominal size) reinforced with 1.6 mm dia. Mild steel wire 0.72 809.92 Rmt

including roughening,cleaning, fixing and finishing in cement mortar

1:3 and curing complete.(E) 100mm thick

Providing and fixing 0.90 meter high fencing with 1.20 meter long

M.S. Angle posts 40 mm. X 40 mm. X 6 mm. And oil painting

coats fixed at 2.5 mt. C/c with Three horizontal lines and two

diagonals of galvanised steel barbed wire weighing 9.38 Kg. Per

meter, strained and fixed to posts with G.I. staples, including fixing

posts in compound wall

Providing and fixing of highly durable precoated Roofing Sheets

having high quality color coating throughout the roof and having

minimum 0.6 mm thickness .The Color Coated sheet Roofing fixed

46 with galvanized iron /color powder coated J or L Hooks, Bolts and 100.37 727.13 Smt.

nuts 8mm diameter with bitumen and G.I. limpet washer or color

powder coated limpet washer. filled with white lead complete as per

approved sample and color as directed by engineer in charge

Providing ridges or hips 600 mm overall in precoated G.I. sheet class-

47 3 fixed with G.I.J. or L Hooks and nuts 8mm dia G.I. Limpet and 11.70 641.94 Smt.

bitumen washer complete. (1) 0.60 mm thick sheet.

Carring out plinth treatment to post construction / existing structure

by spraying chemical solution for termite control treatment including

labour and material consistment with I.S.I specification. Using

Chlordene and Chiorpurfiles 20 EC. As Per 6131_paret-II

Consentration Weight one percent is recommended i.e one litre 20 EC

chemical emulsion with 19 liter give 1 % concrentration inclusive of

one litre chemical emulsion appication at the rate of 5 Litre chemical /

Sqm of surface is recommended as per I.S

Provoding and supplying small dust bin (Green,Blue,Red,Black

49 yellow,) 7 Litres as directed by Engineer in charge, Approve Make- 40.00 277.75 No.

Cello, Aristo, Nayasa

Provoding and supplying big dust bin (Green,Blue,Red,Yellow)

50 Litres as directed by Engineer in charge Approve Make- Cello, 24.00 444.40 No.

Provoding and supplying big dust bin ( Green,Blue,Red) 50 Litres as

directed by Engineer in charge Approve Make- Cello, Aristo, Nayasa

Providing and Fixing 5mm thick Acrylic Name Plate for dark zink

glare with braille lippi and fixing with double sided bonding tap and

screws as per direction of Engineer in charge of Size having 12'. X 4 '

Providing and Fixing 5mm thick Acrylic Name Plate for dark zink

glare with braille lippi and fixing with double sided bonding tap and

screws as per direction of Engineer in charge of Size having 12'. X

Painting two coats (including priming coat) on new steel and other

metal surface with synthetic enamel paint, brushing to give an even

shade including cleaning the surface of all dirt, dust and other foreign

Construction of a soak well of as per the approved drawing & design

etc.in all sort of soil complete as directed and approved by engineer

incharge.( The internal In-to-in dimension shall be considered for

Construction of a septic tank as per the approved drawing & design

etc.in all sort of soil complete as directed and approved by engineer

incharge. ( The internal In-to-in dimension shall be considered for

Description Of Item Quantity Rate Unit Amount

RCC GSR ( description of item for turnkey tender)

Preparing structural design of RCC Under Ground / Partially under

ground / above high ground level Reservoir of required capacity as

per relevant I.S.s and constructing the same, including excavation in

all types of soil strata (including rock) including shoring strutting if

required, for loose soil / to protect from collapse due to near by traffic

load, casting 100 mm thick P.C.C. leveling course in M-10, Refilling

the pit with proper soil and disposing of the surplus stuff within a

lead of 50 meters. Including cement plaster in CM 1:2 with approved

water proofing compound to inside water touching surface to

container. Including all types of labour and material charges of

lowering, laying, erecting / hosting and jointing of pipe assembly to

inlet, outlet overflow, washout and bye pass arrangement as per

hydraulic design. Providing and fixing accessories like MS / GI

Ladder, CI Manhole frame and cover, water level indicator, adequate

cowl type ventilators or lantern type ventilator with stainless steel jail.

B.B. Masonry chambers for valves. Providing and applying three

coats of cement paint / snowcem to the out side face of structure. It

also includes satisfactory water tightness test as per relevant I.S. code

and painting name of scheme and capacity on the tank as per

direction of engineer in charge. List of Indian Standards for Design of

GSR / SUMP:-The structural design of GSR shall be in accordance

with provisions relevant I.Ss. (1) I.S. 3370 part I & II 2009 or latest

revised (1.1) I.S. 3370 part III & IV 1965 or latest revised (2) I.S.

– 2000 or latest revised. (3) I.S. 1893 – 2000 – 1984 or latest revised.

(4) I.S. 875, Part – 1 to 3, 1987 or latest revised. General

Specifications:-(1) Water depth in container shall be adopted as per

data of tender. If water depth is not specified the suitable water depth

/ acceptable to field engineer in accordance with hydraulic

requirement shall be adopted for capacity. (2) Shape of container (in

plan) specified by in data shall be adopted in absence circular shape

shall be adopted. (3) Size shall be fixed as per availability of space

Providing and fixing washbasin with single hole for pillar tap with

M.S. brackets painted white including sutting holes and making good

58 the same but excluding fittings.(A) Vitreous China:(ii) Flat Back 9.00 2161.44 No.

washbasin 550 mm x v 400mm size. (i) In white colour including CP

Brass west , MI Fisher union and Pillat tap

Providing & fixing Stainless steel 316 Grab Bar 40mm dia.75Cm

long rail.as directed and approved by engineer incharge.

Construction of ICN Chamber as peras directed and approved by

engineer incharge.

Providing and fixing screw down bib taps of following size.(B) Brass

chromium plated screws down Bib Tap. (i) 15mm dia.

Constructing brick masonry chamber for underground C.I. Inspection

chamber and bends with bricks having crushing strength not less than

35Kg/Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x

610mm intenal dimensions total weight of cover with frame to be not

less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15Kg.)

(R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc. complete.(i) Inside

dimensions 455mmx 610mm and 450mm deep for single pipe line.

Providing & fixing urinal of Approved quality including connecting

the urinal with waste pipe, trap etc. complete (A) White earthenware

63 flat back or corner type (including Angle cock,Waste 12.00 1911.91 No.

coupling,connection pipe & waste pipe) as approved by engineer

Providing and fixing wash down water closet (European type W.C

pan) with integral P or S trap including jointing the trap with soil

64 pipe in cement mortar 1:1 (1 cement : 1 fine sand) (seat cover,Jet 5.00 2260.14 No.

spray & Flush Tank to be measured Including) (A) Vitreous China (I)

Long pattern white as directed and approved by engineer incharge.

Description Of Item Quantity Rate Unit Amount

Providing and fixing water closet squatting pan (Indian type W.C

pan) size 580 mm (earthwork, bed concrte, foot rests,Flush Cock and

trap to be measured and including paid) (A) Vitreous China (I) Long

pattern white as directed and approved by engineer incharge.

Providing erecting and fixing double coated ISI water tank of

66 required capacity each with all necessary fittings and connection etc. 20500.00 3.95 No.

complete on terrace

67 Providing & fixing UPVC ball valve(A) 40mm dia. 9.00 1687.71 No.

68 Providing & fixing UPVC ball valve(A) 25mm dia. 21.00 650.84 No.

69 Providing & fixing UPVC ball valve(A) 15mm dia. 8.00 440.56 No.

Providing and fixing S.W. gully trap with C.I. grating brick masonry

chamber and water tight C.I. cover with frame of 300mm x 300mm

size (inside) with standard weight.(i) Square mouth traps.(B) 150mm

x 100mm size P or R type

Providing and fixing PVC SWR Nahni trap IS 14735 for drain -

mm diameter with jali of the following nominal diameter of self

cleansing design with C.I scread down or hinged grating including

the cost of cutting and making good the walls.

Providing & erecting open well horizontal mono block pump set with

cast iron body, compete for three phase submersible motor having (A)

72 For 1.5 HP 3 phase open well horizontal mono block pump set 4.00 12135.15 No.

suitable for 190 LPM @ 20 mtr head suitable for 40 mm dia delivery

73 Providing & fixing 110mm dia PVC cowl vent to pipes. 36.00 19.70 No.

74 Providing & fixing 75mm dia PVC cowl vent to pipes. 13.00 30.81 Rmt

Providing laying and jointing in true line and level 40mm dia.

U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall with

75 the help of clamp at every two metre C/C or shall be concealed as 501.00 148.12 Rmt

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent, including cost of all

Providing laying and jointing in true line and level 25mm

dia.U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall with

76 the help of clamp at every two metre C/C or shall be concealed as 855.00 91.84 Rmt

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent, including cost of all

Providing laying and jointing in true line and level 15mm

dia.U.P.V.C. Pipe ( SCH- 40) for cold water including fittings as

approved by Engineer In Charge. Pipe shall be fixed on the wall with

77 the help of clamp at every two metre C/C or shall be concealed as 305.00 72.65 Rmt

directed including necessary fittings etc. including testing of pipe and

joints and fixing the same with adhesive solvent, including cost of all

Providing & fixing to wall ceiling and floor 6.0 kg F/cm2 working

pressure PVC pipes of the following out side dia. Special density

complete with special flange compression type fitting,wall clips etc.

including making good the wall ceiling and floor.(G) 160 mm dia

Providing & fixing to wall ceiling and floor 6.0 kg F/cm2 working

pressure PVC pipes of the following out side dia. Special density

complete with special flange compression type fitting,wall clips etc.

including making good the wall ceiling and floor.(G) 110 mm dia

Providing & fixing to wall ceiling and floor 6.0 kg F/cm2 working

PVC pipes of the following out side dia. Special density complete

with special flange compression type fitting,wall clips etc. including

making good the wall ceiling and floor.(F) 75 mm dia

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in

flooring treads of steps and landing laid on a bed of 12mm thick

81 cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with flush 464.63 1120.36 Smt.

pointing in white cement.

Item Code:14008CA,No:14.29(C1),Pageno:131

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in

82 skrting risers of steps and dedo on 10mm thick cement plaster 1:3 (1- 165.55 1195.02 No.

cement : 3-coarse sand) and jointed with white cement slurry

Description Of Item Quantity Rate Unit Amount

Providing recharge well as per the design approved by Engineer

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS PVC

insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push &

accessories and earth continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame covered with

textured/metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed.(e) in existing pipe erected flushed on

wall/ceiling complete,Cat. III

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of .ISI marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected with 6A Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with earth

continuity of following type erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.(e) in existing

pipe erected flushed on wall/ceiling complete,Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

86 PVC / Metallic/Wooden box covered with appropriate front plate 25.00 364.61 Pt.

modules erected on / in wall / ceiling as per pipe erected with

following type of accessories.[I] For 6A Plug and 6 a switch with 2-

1.5 sq.mm Cu. Wire from nearby switchboard/mcb db board(e) in

existing pipe erected flushed on wall/ceiling complete,Cat. III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on

87 PVC / Metallic/Wooden box covered with appropriate front plate 25.00 499.95 Pt.

modules erected on / in wall / ceiling as per pipe erected with

following type of accessories.[II] For 16A Plug and 16 amp switch

with 2-2.5 sq.mm Cu. Wire from mcb db board.(e) in existing pipe

erected flushed on wall/ceiling complete,Cat. III

Point wiring for on board Looped Plug with 6A Modular type switch

& 5 pin socket erected on PVC / Metallic/Wooden box, single

88 mounting base frame covered with textured / metallic/white front 56.00 241.39 No.

plate modules erected on / in wall / ceiling with following type

accessoriesCat. III

Providing following type of Modular Type Accessories mounted with

PVC / metallic/Wooden box, single mounting base frame covered

89 with textured / metallic/white front plate , modules erected with 5.00 190.89 No.

necessary connections as per site situation directed by Engineer In

charge.(10) 6/16Amp. Universal socket

Providing following type of Modular Type Accessories mounted with

PVC / metallic/Wooden box, single mounting base frame covered

90 with textured / metallic/white front plate , modules erected with 85.00 24.24 Rmt

necessary connections as per site situation directed by Engineer In

charge.(7) Blank Plate Single,Cat.III

Providing and erecting ISI mark embossed Medium class RIGID

PVC PIPES (F.R.L.S.)of following size complete to be erected on/in

91 wall or ceiling erected with necessary PVC fittings & Junction boxes 1530.00 23.23 Rmt

fixed with adhesive solution & Clamps with following dia of pipes,

in approved manner as directed (a) 20 mm

Description Of Item Quantity Rate Unit Amount

Providing and erecting ISI mark embossed Medium class RIGID

PVC PIPES (F.R.L.S.) of following size complete to be erected on/in

92 wall or ceiling erected with necessary PVC fittings & Junction boxes 382.00 32.32 Rmt

fixed with adhesive solution & Clamps with following dia of pipes,

in approved manner as directed (b) 25 mm

Providing & erecting PVC Corrugated Flexible Conduit with

93 required nos. of coupling, PVC bushes, Check-nuts etc. complete of 19.00 20.20 Rmt

following sizes.(2) 25 mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected concealed in /flushed on wall/ceiling, with

1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size,(E) in existing

pipe,(a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected concealed in /flushed on wall/ceiling, with

1.5 sq. mm copper conductor FRLS PVC insulated stranded wire of

green colour for earth continuity of following size,(E) in existing

pipe,(b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour

for earth continuity of following size,(E) in existing pipe,(a) 2 wire

providing and erecting Mains with 1.1 KV grade FRLS PVC

insulated ISI marked stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded wire of green colour

for earth continuity of following size,(E) in existing pipe,(b) 2 wire

Supplying and erecting Flexible PVC insulated multi strand multi

98 core 1.1 kv grade ISI marked copper wires of following size to be 58.00 44.44 Rmt

erected as directed.(e) 1.50 Sq.mm 3 core round PVC sheathed

Supplying & erecting approved make LAN cable of following size in

existing pipe as per direction,[C] CAT -

Providing & erecting Switch board for Computer or electric apparatus

consisting of following modular type accessories mounted with PVC

/ Metallic concealed/open box with single mounting base frame

covered with textured/metallic /white front plate,modules erected

with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug ,For Modular Type Accessories ,Cat. III

101 Decorative call bell Ting-tong box type 250 volts complete erected 2.00 68.68 No.

Supplying and erecting LED indoor fittings with LEDs of wattage

0.2 Watt to 0.5 Watt assembled on single MCPCB, with housing used

as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company mark/name 160V to

270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.),(A) Tube Light with integral driver,(ii)

20 Watts, Surge - 2KV,IP-20, conventional 4 feet,Cat-lll

Description Of Item Quantity Rate Unit Amount

Supplying and erecting led lamps with following wattage capacity of

220 to 240 voltage, minimum 15000 burning hours life, 500 V in

built-surge protection,Polycarbonate diffuser, mounting suitable for

E14 / E27 / B22 lamp holders, pf >= 0.5(A) LED Lamps integral

type, with PC diffuser suitable LAMP holder,(ii) 8 watts ,Cat-III

Supplying and erecting LED street light / Flood light fittings with

High power White LEDs wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w and corrosion free

High pressure die cast aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more

104 than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio 4.00 4997.48 No.

>0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE:

Below description have shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any wattage capacity

between the ranges shown.)(A) Street Light (IP-65), Surge protection -

4KV integral and ,Light must have 440VAC line supply with over-

voltage protection.,(ii) 48 to 60 Watts,Cat-lll

Supplying and erecting triple pole & neutral 440V / 500V panel

mounting Copper Busbars with four equal Nos. of electrolyte bus

having current density not more than 1.6 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with colour insulating tape

for phase sequence of following current carrying capacity, erected

with necessary bus bar supports /insulators, main cable socket to each

bar, erected in existing cubical panel with necessary connections. (A)

Suitable for 100 Amp. capacity

providing and erecting Miniature circuit breaker single pole 6A to

25A suitable to operate on 240 V A.C. system and having breaking

capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark , Cat.III

Providing & erecting 240 V MCB double pole switch for lighting

107 Load (B Curve) having 10 KA breaking capacity & confirms to IS : 1.00 278.76 No.

8828 in existing box having following capacity (A) 6 to 32 Amp.

Providing & erecting 240 V MCB double pole switch for motor &

inductive load (C Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following capacity ,(A)

6 to 32 Amp. Cat.III

Sheets steel powder coated enclosure suitable for incorporating

One/Two nos. MCB.

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

110 without MCB to house appropriate nos. of MCBs.(The DBs should 14.00 2913.85 No.

be used of same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type outgoing Per phase

isolation type (PPI) (b) sheet steel double door,(ii)6 way

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

111 without MCB to house appropriate nos. of MCBs.(The DBs should 2.00 885.77 No.

be used of same company of MCB to be used) suitable for (A) single

phase incoming and horizontal single phase outgoing (b) sheet steel

double door,(ii)6 way (IP-43)

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

112 without MCB to house appropriate nos. of MCBs.(The DBs should 2.00 1152.41 No.

be used of same company of MCB to be used) suitable for (A) single

phase incoming and horizontal single phase outgoing (b) sheet steel

double door,(ii)8 way (IP-43)

Description Of Item Quantity Rate Unit Amount

Providing and erecting Sheet Steel powder coated MCB distribution

board - flush / surface mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 &

113 without MCB to house appropriate nos. of MCBs.(The DBs should 2.00 1492.78 No.

be used of same company of MCB to be used) suitable for (A) single

phase incoming and horizontal single phase outgoing (b) sheet steel

double door,(ii)12 way (IP-43)

Providing and erecting Approved make RCCBs conforming to IS:

12640 and having sensitivity of 30 mA and Short Circuit withstand

capacity of 10 KA and suitable for operation on 3 phase and neutral

415V,50Hz. having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic component for

following Max. rating erected as directed.,(ii) 40Amps. FP , Cat. III

Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped

G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron

galvanising, Inner pipe dia of 40 mm having 200-250 Micron

galvanising, connection terminal dia of 14 mm with constant ohmic

115 value surrounded by highly conductive compound with high charge 2.00 4591.46 Kg.

dissipation suitable for following type of applications with chamber

and heavy duty cover.(approved make OEM has to submit test

certificate including value of earth resistane of installation.(a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

116 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 5.00 794.87 No.

Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board necessary IP-

42 and above protection as per approval from engineer incharge made

from 14 SWG thick CRC M.S. sheet for outer body & doors,

SWG thick CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel including cutting,

bending, drilling, welding, riveting with internal partitions & cable

alley as per requirements & instruction of engineer-in-charge with

erection of supplied switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-base

Plates, sufficient nos. of hinged doors, handles with locking

arrangement and rubber gasket,heavy duty end terminal

connection,danger notice board,necessary ventilation,earthing strip

complete. The Panel shall be painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus bars, inter connecting

mains & Copper Aluminium strips, meters, Fuses etc. The dimension

shall be measured excluding base beams) The panel shall be supplied

with following approved manufacturers with following size.(B) The

standard companies switch gear shall be used and only manufacturers

at CPRI approved factory ,(i) with 350mm depth

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe of following

size of cables.(B) 4 core 6 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on

wall with necessary clamps or in existing trench / pipe of following

size of cables.(C) 4 core 10 Sq. mm

Making trench in soft soil of suitable width of 90 cm deep for laying

120 cable or locating the fault all over the run and back filling the same 75.00 46.46 Rmt

and making the surface as normal ground.

Making trench in Hard Murrum / Tar Road of suitable width of

cm or required depth for laying any size of cable or locating the fault

all over the run and back filling the same and making the surface as

Description Of Item Quantity Rate Unit Amount

Supplying following size of Light duty “A” Class G.I . Pipe &

erecting as directed by Engineer-in-charge. (B) 50 mm dia

Providing & laying approved make Double walled corrugated pipes

(DWC) of polyethylene(conforming to IS 14930 II )with necessary

123 connecting accessories of same material at required depth in existing 120.00 62.62 No.

trench for laying of cable. below ground / road surface for enclosing

cable (A)50 mm outer dia

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.(B) 2 to

Providing and, fixing heavy duty flange type brass cable gland with

rubber ring for PVC insulated armoured cable complete with out

going tails, insulating tape etc for following size of cables.(C) 2 to

Solder less crimping type Aluminium lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (A) 6 Sq.mm.

Solder less crimping type Aluminium lugs conforming to IS suitable

for cable of following size evenly crimped with high pressure tool &

connected to switchgear terminals with brass/cadmium plated nut

bolts in an approved manner. (B) 10 Sq.mm.

Providing & erecting Approved make Power Saving 50 Watt Ceiling

Fan with double ball bearing ISI mark with Condenser 230 volt A.C.

128 50 Hz 1200 mm sweep complete having 3blades with aluminium 100.00 1948.29 Rmt

blades with , canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

Supplying and erecting 19 / 20 mm. nominal bore Medium Class

129 M.S. Pipe down rod erected duly painted for fan complete with 190.00 108.07 No.

proper insulation without leakage and earthing.

Supplying & erecting single phase approved make industrial exhaust

fan suitable for medium duty ring mounted low noise operation

suitable for medium duty having following dia size and maximum

speed in RPM,[A] 305 mm dia 900 RPM,Cat.II

131 Providing suitable M.S. louver shutter of the Exhaust fan. 9.00 368.65 No.

Providing window frame suitable for erection of Exhaust fan

132 complete covering the remaining portion of window with 15 mm. 9.00 172.71 Each

thick plywood and colour washing to match the colour of the wall.

Supply of approved make FRP Pole having following specifications:

FRP Light Pole made by CNC filament winding machine using

thermoset resin polyester/epoxy resin system) having minimum 62%

glass content. The pole should be in one piece and tapered round in

shape, having smooth finish and should be totally free from corrosion

as well as non conductive & shock proof Pole should be provided

with FRP Anchor Base and it should be heavy duty, or MS Material

duly painted with Epoxy paint. Pole should be flame retardant as per

IS 6746. Resin used shall be UV resistance and pigmented. A highly

weather resistant polyurethane coating shall be applied to the pole

after applying suitable primer system that ensures proper adhesion of

133 the paint. Minimum coating thickness shall be 80 to 100 micron. 12.00 8252.71 No.

Deflection of the pole shall not exceed more than 10% of the length

of pole for the given load“ Pole should be generally made as per the

dimensional data, performance criteria and some interchangeability

features of poles as per standard ANSI C 136.20 latest version or

ASTM D 4923/01 including cable termination box with necessary

accessories . The size of pole and type of installation with foundation

as per manufacturer details and site requirement are as below .(3)

Suitable for direct grouting & Single arm Bracket. [D] Overall length

of 5 Mtr. Average Thickness: 7mm.

Top/ Bottom OD Dia: 90/145 mm ± 3mm approx. approx. Weight of

Pole 25 kg approx.

Providing Aluminium arm bracket of having 2 sets of suitable SS304

134 hardware for fixing the brackets & spread of 1.2 Mtr (Suitable for 89 12.00 2234.12 No.

to 114 mm pole top dia) (A) Single arm bracket

Description Of Item Quantity Rate Unit Amount

Supplying & erecting approved make SMC press moulded composite

FRP. loop-in, loop-out approx. 2mm thick box complete with

Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob

135 & hinged doors as per requirement having locking arrangements with 12.00 515.10 No.

mounting clamp with nuts, bolts & washers suitable for erection on

pole with cable clamps& earth bolt of following size of box. (B)

250mm x 200mm x 100mm [deep]

Providing 1:2:4 cement concrete foundation & 70 % PCC from

bottom including excavation for the pole of size 45 x 45 x 100 cm.

Deep in below ground level with plinth of 45 cm x 45 cm (or 45 cm

dia x 45 cm) high upper ground level with necessary curing and

finishing in approved manner.

( for 4 & 6 mtr pole)

Supplying & erecting approved make Digital time switch having

lithium cell 6 years operative and operate battery backup 1 channel

day clock with 14 memory programme, suitable to operate on 240V +

5%, 16A with, floating contacts Minimum switching setup time

minimum & LCD display. Also comprised permanent ON/OFF

switching. Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover erected as required with

necessary connection erected as directed.

Supplying & erecting Amplifier having following specification:

Power Output :250W (RMS) (300W Max.)

inputs : 6 Misc. & 2 Aux.

frequency Response :50-1500HZ I3db

Tone Controls :Cut & Boost type

LED Meter :5 LED Arrays

The amplifier suitable to operate 240V A.C.& 24volt D.C. (Battery)

with automatic changeover from AC to Battery operation, duly

protected by wrong Battery Polarity connections. [[Approved by

Competent Authority i.e. not Below the rank of Executive Engineer ]

Supplying & erecting recess wall mounting speaker with 5W rated

input power 3.3 K. Ohms / 3W impedance, 100 - 10000 Hz

139 frequency response with 6 inch dia. cone type 8 ohms speakers duly 8.00 591.86 Each

fitted in ABS plastic cabinet of colour match with wall or ceiling of

following size. (b)Square shaped 260 x 260mm size speaker

Supplying, installing and testing approved make microphone for All

purpose, with frequency response of 100 - 11000 Hz, having

sensitivity 2.2mv / Pa & impedance 500 Ohms (LO- Z) supplied with

quick detachable holder, 6 mtr twin core cable & 3 pin XLR

connector. [[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

Supplying and erecting approved make panel mounting type Digital

Ammeter having 3 digits LED display, external CT operated,

141 calibrated for 0 to 1000 Amps suitable to operate on 500 Volt AC , 3.00 1558.43 No.

erected on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range

erected on existing panel board with all connection, wiring etc .with

manufacturers calibration certificate.

Providing & erecting L.T. Current Transformer with bar primary 50/5

143 to 1000/5 ratio 15 VA burden erected in existing CRCA box duly 2.00 274.72 No.

secured with insulating materials connected to the meter

Supplying and erecting approved make suitable panel indicator LED

type lamp, lens cover, complete erected with necessary connections.

Supplying and erecting Ammeter / Voltmeter selector switch for

145 phase AC Supply 500 V on existing panel board with necessary 6.00 317.14 Rmt

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat

146 flexible Submersible copper cable approved make of following Size. 35.00 146.45 Sq.Mtr

(c) 3 Core x 4 Sq. mm

Supplying rubber matting of following thickness as per IS:15652/IEC

Description Of Item Quantity Rate Unit Amount

Providing ABC Type Fire Extinguisher 6 Kg Isi Marked All

Required Fitting Accessories.(M.R.)

149 Major Repair of Doors and Windows 35.00 1069.59

I/We am/are willing to carry out the work at………………….% above/below percent

(Should be written in figures and words) of the estimated rate mentioned above.

Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct……………………… % below Deduct……………………… % Above

In words In words