REPAIRS TO ROOF, FLOOR, JOINERY ETC INCLUDING CONNECTED APPROACH PATH IN CERTAIN SEWAGE SUMP/PUMP HOUSE AT MIL STN JAMNAGAR.

Amount

Taking down all existing roof treatment and demolition of cement concrete padding/levelling course incl wire brushing and cleaning loose dust etc from surfaces of RCC roof incl flashing and juntion of parapet complete all as specified.

Demolition of cement (un-reinforced) in any position not otherwise specifically provided complete all as specified and as directed.

M&L 25mm thick PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course incl finished even and smooth using extra cement complete all as specified an aas diected.

M&L 10mm thick screed bed in cement plaster 1:3 on padding layer for roof treatment with WPC complete all as specified

Supply only liquid waterproofing compound

Water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment / specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 3 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non woven polyester fabric or weight not less 150 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm 9 minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. Note:- (i) Laying of APP based membrane shall be done by torch on method and as per manufacturer's instructions.Sstarting at lowest point in slope roof by using a LPG torch to fuse plastic membrane on bottom face of membrane and applying uniform pressure with a roller/wet cloth to ensure to remove entrapped air, if any. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and all overlaps and joints are properly sealed as per manufacturer's instructions. (iii) Applying two coats of Bituminous aluminium paint on top of APP membrane cover including testing on completion complete all as specified and directed.

Taking down of cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

M&L for rendering 5mm thick in CM 1:3 on ceiling to be finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finishing the surface even and even smooth without using extra cement complete all as specified and as directed.

M&L 15 mm thick rendering in in two layers 5mm thick inCM 1:4,over 10mm thick cement plaster in CM 1:6 on fair face of brick work/Stone or concrete surface to be finished even and smooth without using extra cemen Including WPC compound 3% by weight of cement.(Note :a) Intergial WPC Compound shall be used in sencond layer,b) Intergial WPC shall be paid seperately on supply only.

M&L for preparation and applying three coats of white wash on new plastered surface of celing all as specified and directed

Preparation of newly plastered surfaces of wall incl sweeping clean with brush to remove loose dust, sand, etc and applying two coats of heavy duty waterproofing coat (Dr Fixit Wounderproof-1 or equivalent) by mixing water @ 25-30% to make slurry coating and allow 4 to 6 hrs time for drying up of first coat before application of second coat in perpendicular direction of first coat and further left to dry for 4 hrs complete all as specified and directed as per manufacturer instructions.

M & L for preparation of new plastered surface of wall and applaying two coat of oil bond distemper and 3 mm putty all as specified and directed

M&L preparation of newly plaster surfaces of walls over 10cm width and applying two coats of weather coat exterior paint over a coat of compitible primer pn plastered plastered surfaces complete all as specified and as directed

M&L Preparation of old surfaces of wall removing nails including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc by hand held sander / long handle sander including cornices, pilasters etc (Plastered or unplastered surfaces) , filling undulation and holes with putty and applying one coat of oil bound distemper with roller finish on walls etc. Complete as specified and as directed by Engineer-In-Charge.

M&L preparation of old painted surfaces of wood/ wood based materials of any description over 10Cm width or girth and applying one coat of synthetic enamel paint etc. complete all as specified and directed by Engineer-In-Charge.

M&L preparation of old painted surfaces of steel/ iron of any description over 10Cm width or girth and applying one coat of synthetic enamel paint etc. complete all as specified and directed by Engineer-In-Charge.

Material and labour for complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrapers, any number of coats and any width or girth etc, the area of application should be cleaned thoroughly, remove all dirt, dust and uneven elements from the surface by washing and scraping and all the unevenness in the surface should be corrected by filling the exterior wallcare putty, surface should be sanded down with fine grade sand paper hand held sander for smoothness and applying one coat of exterior primer and 02 coats of Exterior Weather Coat Emulsion Paint of white or tinted shade as per manufacturer instruction complete all as directed and specified.

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls by using chesel/hammar.Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement, clean loose rust from bars manually with brush . fixing new supplymentary bars if required,either by tying it with existing bars or by welding on it. Applying eppoxy bonding agent and making good with polymer modified plaster/micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including formwork complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and as directed.

M&L coloured Non skid ceramic joint free floor tiles 7-8mm thick (Square / rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm set and jointed in neat cement slurry and pointed in coloured cement over and including bedding layer 15 mm thick in cement mortar 1:6 complete all as specified and as directed.

M & L for Glazed ceramic tiles, coloured (light colour as approved), of size 300x 600 OR 350x 250x 7mm/ 450X 350X 7mm thick on vertical surfaces such as in skirting/dado etc s set and jointed in cement slurry over 10mm thick rendering in cement mortar (1:3) and pointed in white cement with pigment to match the colour of tiles complete all as specified and as directed.

M&L Powder coated aluminium sliding window shutters, aluminium section including necessary joining cleats, glazing clips, Aluminium grill (decogrill Design no 20) and F/h type frame, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150 mm long (1 No.) or hinges type B-21 100 mm long (2 nos.), suitable handle or Star lock, (1 no.) gasket,Aluminium wire cloth 0.45mm dia of f wire and average width of aperture 1.40mm incl necessary channel frame work and 5mm thick float glass including fixing arrangement and clips complete all as specified and as shown on drawing NOTE : (ii) Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, etc (iii).comprising frames of section No : 20831 three track top, 20832 three track bottom, 20736 top and bottom shutter, 20738 inter lock, incl "C" channel and "L" angle, roller bearing, rubber beading, consealed lock,

S&F powder coated anodised Aluminium ventilator with fixed aluminium frame of size 60mmx40mmx1.98mm fixed in vertical position with aluminium vertical members and half portion to be provided with aluminum heavy duty adjustable loovers and 4mm thick pinhead glass and remaining portion to be louvered using 4mm thick pinhead glass and louvered portion covered with Aluminium wire cloth 0.45mm dia of f wire and average width of aperture 1.40mm incl Aluminium grill (decogrill Design no 20) and F/h type frame, rubber neoprene packing, anodised aluminium snap beading, screws, complete all as specified and as shown on drawing Note : Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading grill loovers etc

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area n.exc 1.5 sqm all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) each area exc 1.5 sqm but n.exc 4.0 sqm all as specified and as directed.

S&F Pressed steel frames for doors size 105 mm X60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, .

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and as directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawingcomplete all as specified and as directed.

S&F factory made 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated.

S&F 100mm butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed,type B1,complete all as specified and as directed.

S&F 250 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium complete all as specified and as directed.

S&F Extruded aluminium alloy handles 150mm long, fabricated type, anodised complete all as specified and as directed.

S&F Aluminium anodised barrel tower bolts, 150 mm long, of extruded section complete all as specified and as directed.

M&L preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer,complete all as specified and as directed.

Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including suface excavation and removing debris outside MD Land complete all as specified and directed.

M&L for cement concrete sub base 75mm thick type D-2 1:4:8(40mm graded aggregate) complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20 mm Graded Stone Aggregate) 40 mm mm thick, as in floors, etc, and finished the Cement Concrete Surfaces Even and fair with outusing Extra Cement, complete all as specified and as directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade A

M & L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

M&L 100mm thick PCC type C-2, 1:3:6 (40mm graded stone aggt) as in path, hard standing, parking floors etc. complete all as specified and as directed.

Demolition of Stone slabs or interlocking tiles of any description or thickness in floors, aprons etc.laid dry complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block (coloured) any shape and size conforming to IS 15658-2006 of 60mm thick M-35 grade etc complete (with grey cement and pigment) over 50 mm thick sand coushioning complete all as specified and directed.

Providing, cement concrete in kerbs type B1, 1:2:4 (20mm rounded or chamfered on edges graded aggregate) having rounded or chamfered on edges including necessary formwork complete all as specified and directed.

S & F Vitreous China Squatting Pan ‘ORISSA’ Pattern, size 580X440 mm White, with , Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan (excluding Flushing Cistern and Flush Pipe), and connected Items, complete all as specified and as directed.

S&F in repairs Vitreous china wash basin, white , flat back , size 550 x400mm excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F 10 litre capacity low level PVC flushing cistern (white), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and directed.

S&F in repairs bib taps cast copper alloy chromium plated, fancy type, long body, concealed type with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule & fixed 15mm bore complete all as specified and directed.

S&F in repairs angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repair 15mm Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, joint with adhesive taflon type screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S &F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts complete all as specified and directed.

Supply, lay, connect and test GI tubing ,medium grade with all fitting, fixed to walls, floors, ceiling etc. complete of size 15mm bore Fixed in repairs, complete all as specified and as directed

Supply, lay, connect and test GI tubing ,medium grade with all fitting, fixed to walls, floors, ceiling etc. complete of size 20mm bore Fixed in repairs, complete all as specified and as directed

S&F Rotational moulded polyethylene water storage tanks (cylindrical, vertical with closed top) 500 Litre capacity, hoisted and fixed in position, with lid, tounge nipple for inlet, outlet connections etc. position with S&F 20mm PTMT float valve fixed in repairs, complete all as specified and directed

SHAM AND CO

jitendra c joisar

S H CONSTRUCTION

Sukhi Electricals

suvidhiconstruction

VINUBHAI P. CHANDRA

fakhrie apostrical

Ravi enterprise