SPECIAL REPAIR TO BLDG NO P-42 OF 611 EME BN AT AHMEDABAD CANTT

Amount

Taking down chowkats or frame with shutters (without taking off shutters from the frame) n exc 1.5 sqm each

Taking down chowkats or frame with shutters (without taking off shutters from the frame) exc 1.5 sqm and n exc 4.0 Sqm each

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Demolition of Brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc., but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for Brick work with sub class 'B' bricks built in CM (1:6) straight or curved on plan & exc 6m mean radius with old size bricks.

S/F coloured plain/printed glazed tiles of size 300 x 450 x 7 mm, on vertical surfaces such as skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10 mm thick rendering in CM 1:4

S/F Non skid coloured plain/printed glazed tiles of size 300 x 300 x 7 mm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Dismantling asbestos cement (corrugated or semi corrugate, etc.,) sheets in roof covering complete all as specified

S&F prepainted galvanized aluminium zinc coating GI base corrugated steel sheet 0.60mm thick of any colour as directed by GE having tensile strength of 550MPa as in roof covring/clading to wall, fixed with self tapping screws as specified. Complete all as spd and directed (Note: Corrugation shape of sheet shall be approved by GE)

S&F prepainted galvanized aluminium zinc coating GI base plain sheeting steel sheet 0.60mm thick of colour as directed by GE for ridge having tensile strength of 550MPa as as in roof covring/clading to wall, fixed with self tapping screws as specified. Complete all as spd and directed (Note: Corrugation shape of sheet shall be approved by GE).

S&F for Butt hinges of size 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21

S&F for Butt hinges of size 75mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21

S&F 0.56mm thick plain aluminium sheeting, Alloy 31000H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed)

Taking down cement or lime plaster of any description from stone or brick walls etc., including raking out joints, hacking for key scrubbing down with water and disposing off the rubbish complete all as specified and directed

M&L for 15mm thick rendering on fair faces of brick/concrete surfaces in CM (1:4) finished even and smooth without using extra cement mixed with water proofing compound (Note :- Supply only WPC will be measured & paid separately)

Supply only integral water proofing compound

M&L for 15mm thick rendering on surfaces other than fair faces of brick/concrete surfaces in CM (1:6) and finished even and smooth without using extra cement

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.,) or insulation boards/slabs/blankets, any thickness, including cover fillets

S&F Tee grid suspension system of size 600 mm x 600 mm type-1 made out of roll framed hot dipped galvanised steel zince coated of not less than 120 gm/Sqm, main runner 0.3 mm thick of section 24 mm x 33 mm crross runner 0.30 mm thick of section 24 mm x 25 mm, wall angle shall be 0.63 mm thick of section 24 mm x 24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod, system exposed portion shall be pre painted polyester coated in off whitee/white in colour complete with material, fixing, jointing etc., with Coloured textured designer ceiling board (Everest) 4mm thick of size 595 x 595 mm fixing with screws/clips complete all as per manufacturers instructions and direction. (Make : METROC or METACIL or any other equivalent as approved by GE)

Supply & fix rolled mild steel in joist, angle ,channel as in purlins, rafters cleats etc conforming to Fe-410- W (Gde-E-250)quality A, all as directed.

Dismantling and Refixing of mild rolled steel straps in joist, angle ,channel as in purlins, rafters cleats , ceiling frame etc conforming to fe410 w all as directed by Engr-in-Charge.

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) conforming to Fe-410-W(Gde-E-250)quality-B including distance pieces, cleats etc, all as directed.

S&F steel window with side hung shutters including box type hinges with steel handles and steel peg stay complete but without glazing bars complete including one coat of shop coat of primer.

S&F Stainless steel wire cloth 0.36mm normal dia of wire and average width of aparture 1.40mm and fixed with tinned tacks or Stainless steel wire stapples complete all as specified and directed.

S&F for Pressed steel frames of size 160x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified and directed.

M&L cement concrete cast-in-situ 1:2:4 type B0 (12.5mm graded aggregate) providing in roof kerbs or mud stops, rounded or chamfered on edges in inside of preesure steel frames all as directed.

S & F 30mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed by the Engineer-in-Charge

M&L for preparation of old painted steel surface of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

S/F factory made flyproof mesh panel pvc door shutter 30 mm thick (Style) consisting of frame made out of M.S. frame shall be covered with heat moulded wood grain printed PVC 'C' chanel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, all as per specification & drawing and SS wire gauzed i.e. panel will be of SS wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be screwed to M.S. tubes. The wire gauge shall be stretched to tighten firmly, all as directed by Engr-in-charge.

M&L for preparation of new steel surfaces exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified

M&L for preparation of plasterd wall new surfaces and applying two coats of oil bound distemper over one coat of wall care putty all as specified

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over one coat of primer all as specified

M&L for complete removal of existing treatment and applying two coats of cement based paint over one coat of primer all as specified and as directed

M&L for complete removal of existing treatment and applying two coat of oil bound distemper over 2mm thick wall care putty all as specified

S&F solid PVC door frame of size 50mmX47mm made out of 5mm single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening all as per specifications and drawing shown on sl page No 150 of SSR part II (for item-884)

S&F in repair vitreous china wash down water closet pan (Pedestal pattern) coloured including fixing bolt and plastic water closet seat black closed pattern with flat bottom cover with MS chromium plated hinges devices to matching colour

S&F in repairs vitreous china water closet (squatting pan), orissa patern size 580 x 440mm white with integral, foot rests an including 'P' trap and lime bedding making good to floors complete

M&L for taking up or down steel tubing of 15mm bore and connections, including cleaning for re- fixing or removal to store

M&L for taking up or down steel tubing of 20mm bore and connections, including cleaning for re- fixing or removal to store

M&L for taking up or down steel tubing of 20mm bore and connections, including cleaning for re- fixing or removal to store

S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & both side prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of both side prelam PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading & jointed together with solvent cement, supply & fixing in the frame at site as per SSR specifications & diagram/product drawing shown on sl page NO 146 of SSR Part II with the size of door shutter as required & directed by the Engr-in-Charge.

S&F for GI pipes of 15mm bore, 'medium grade' , with all fitting and fixed complete to walls and ceilings or laid in floors as all directed.

S&F for GI pipes of 20mm bore, 'medium grade' , with all fitting and fixed complete to walls and ceilings or laid in floors as all directed.

S&F for GI pipes of 20mm bore, 'medium grade' , with all fitting and fixed complete to walls and ceilings or laid in floors as all directed.

S&F in repairs 15mm dia Bib taps cast copper alloy, with Chromiun plated crutch or butterfly handle screwed down,for iron pipe or brass ferule complete all as specified and directed.

S&F in repairs 15mm dia pillar taps, cast copper alloy with capstan heads chromium plated screwed down, high pressure with long screwed shanks and fly nuts, screwed for iron complete all as specified and directed.

S & F in repairs 15mm dia stop valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.

S & F in repairs 15mm dia angle valves, Chromium plated crutch or butterfly handle screwed down high pressure, screwed both ends for iron pipes or for unions.

M&L cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth all as directed.

S&F in repair 10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets with flush pipe 32mm dia

S&F in repair tubular towel rail 20mm dia D type and 60cm long between flanges including brackets fancy type brass chromium plated

S & F brass CP Soap dish, 125mm any type, fixed to plugs with chromium plated brass screws (conforming to JAINKO Cat no. SDJ-1 or equivalent)

S & F in repair vitreous china urinals, bowl type flat back size 465 x 355 x 265 mm white including providing and fixing plugs bedding urinal against wall CM 1:2 securing urinal with 60mm long brass screws pointing around urinal back in cement, fixing grating and urion for discharge pipe complete fixed in repairs.

S&F in repair vitreous china wash basin, white, flat back, size 550x400mm including waste pipe, brackets and cutting for and pinning in ends of brackets or erecting stand but excluding taps, chain and plug.

S & F in repair 150mm size brass chromium plated shower rose with sweivel joint, any size, including fixing to steel pipe 15mm dia pipe (conforming to JAINKO Cat no. FSJ-6)

S & F in repair health faucet spray type jet with brass jet, chromium plated, and 1.5m long PVC flexible pipe complete all as specified and directed (conforming to JAINKO Cat no. HFJ-2)

M&L for providing Cast iron floor trap 75mm dia of outlet with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

S&F grating square 150 mm size of PTMT(with waste hole) (Minimum weight 100gms) complete all as specified and directed by Engr-in-charge.

S&F grating square 150 mm size of PTMT(without waste hole) (Minimum weight 100gms) complete all as specified and directed by Engr-in-charge.

M&L 32mm dia Low density poly ethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to wall, ceiling or in floors etc

M&L Low density poly ethylene pipes(LDPE) of pressure rating 6 Kgf/cm2 fixed complete to wall, ceiling or in floors etc 40mm dia

S & F in repair swivel shower rose of PTMT any colour for fixing with 15mm pipe fixed in repairs (minimum weight - 40gms)

S & F in repairs 15mm dia brass CP mixer for mixing hot and cold water screwed down for iron pipe complete all as specified and directed. (conforming to JAINKO Cat no. WCJ-3 or eqivalent)

S&F 150mm long Aluminium anodised, barrel tower bolts of extruded section and fixed

S&F300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Extruded aluminium alloy handles, fabricated type, anodised of size 150mm.

S&F for Curtain rails, of anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc

Figured glass, 3mm thick pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete

M&L 50mm thick PCC of type B-1, 1:2:4 (20mm graded stone aggregate) for padding

M&L for Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes

S&F for Rotational moulded polyethylene water storage tank of 1000 liter capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

M & L for machine cut kota stone slab size as in flooring, stair case landing. treads of steps etc, 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified including 15mm thick screed bed or bedding in cement mortar 1:6. all as specified nd directed

Demolition of cement concrete unreinforced of Concrete of any description and in any position not otherwise specifically provided for where directed.

M&L for machine cut kota stone slab size as in skirting, dado, vertical surfaces etc., 20-25mm thick, laid and jointed with grey cement sluirry mixed with pigment to match the shade of the slab including rubbing and polishing including backing coat of 15mm thick in CM (1:3) complete all as specified

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- ills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite .

M&L for 20mm thick Granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for preparing the existing surface by cleaning thoroughly to make it smooth and free from any foreign matter such as fungus, moss, dust etc by wire brushing and dusting and applying a coat of bitumenous primer conforming to IS : 3384 - 1986 @ 0.30 litre / Sqm and then pressing & laying 3mm thick Atactic Polypropylene Polymer (APP) modified prefabricated with non woven polyester reinforcement five layer water proofing membrane weighing not less than 3.50 Kg/ Sqm comprising of centre core of 160 - 170gsm non - woven polyster matt sandwitched on both sides by APP polymer modified bitumen duly protected on both sides by 20 micron HMHDPE film by torch on application with gas welding torch (Butane torch), and thereover applying a tack coat of 85/25 blown grade bitumen conforming to IS : 702 @ 1.20 Kg / Sqm and finish the top surfaces with aluminium paint (Super Silver Shield) @ 0.150 Ltr / Sqm complete all as specified. as per manufacturer's instructions and as directed. Note :- The WPT work shall be got done through manufacturer's authorised applicator only under strict supervision of manufacturer's technical representative.

M&L for cement concrete (1:3:6), type C2 (using 40mm graded stone aggregate) 50mm thick as in plinth protection inclujding necessary form work and finishing surface even and fair without using extra cement including bitumen joints complete all as specified

Taking down carefully surface aluminium/copper point wiring with PVC casing-capping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.20 mm and white modular mounting cover plates with frame for mounting modular switches, sockets, fan regulators etc. complete for the following :-

One light point controlled by one switch.

One fan / exhaust point controlled by one switch.

One socket outlet 6 amp controlled by one switch on independent board.

One socket outlet 6 amp controlled by one switch on same board with other switches.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings/fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2mm covered with 3mm thick phenolic laminated white shite cover for one 16 amp socket outlet controlled by one switch on independent board.

S&F modular switch piano button single pole one way 6 amp 1 module all as per Legrand Mylinc Cat Ref No 675501 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular switch piano button single pole one way 16 amp 1 module all as per Legrand Mylinc Cat Ref No 675511 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular socket outlet 2 in 1, 2 & 3 pin, 6/16 amp, combined 2 module all as per Legrand Mylinc Cat Ref No 675555 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular socket outlet 2 in 1, 2 & 3 pin, 6 amp, combined 2 module all as per Legrand Mylinc Cat Ref No 675550 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular hum free electronic step fan regulator 100 Watt, 2 module all as per Legrand Mylinc Cat Ref No 675530 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F ceiling rose 6 map, 3 plates polycarbonate body complete. Make – Havells Reo / Anchor Penta PC / SSk as approved.

S &F ventilating fan single phase,230 volts,250mm sweep plastic body with mounting rings all as per Havells cat ref no. Ventil Air-DX or equivalent in Almonard / CG/Bajaja as approved

S&F energy efficient recessed mounted LED luminaries suitable got 2'X2' grid ceiling with flat diffuser and lumen output of 5700 having constant current electronic driver duly connected with 0.5 sq mm white PVC insulated and sheathed three core multistranded copper conductor cable as required Make - Wipro Elate LED CRCO 10 Cat No CRC010R038HP57LG or equivalent in Philips or GE lighting as approved.

S&F LED batten (1.2m) made of CRCA sheet housing with a PC glossy difusser duly prewired connection having a nominal system lumen output of 2000 lumes at a minimum system efficacy of 105 lumens per watt and total power consumption not more than 19 watt incl driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete. Make- Philips cat ref no. ENDURALED BATTEN “BN 108C led 20s PSU CDL WH” or equivalent in wipro or GE lighting as approved.

S&F LED fixture 10 watt including connection as per Wipro Tirm LED NEO cat ref No LL20-111-XXX-65-NE 6500 or equivalent in Philips or Havells as approved.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminium housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable as required all as per Philips cat ref no. WT202W LED6S CW PSU S1 PC or equivalent in Wipro or Havells as approved.

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FR multistraned copper conductor cable (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories of following nominal sizes :-

(a) 2x4 sqmm + 1x2.5 sqmm earth continuity conductor in 20 mm dia conduit.

(b) 2x6 sqmm + 1x4 sqmm earth continuity conductor in 20 mm dia conduit.

S&F Power unit for AC or geyser 3.5 KW 4 module including sunken modular GI metal boxes not less than 1.2 mm thick and white modular mounting plates with frame all as Legrand Mylinc cat ref no. 675558 , 689009,675564 & 675584 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F LED 20 Walt street light made up to pressure dia cast housing with prismatic poly carbonate diffuser and indiviual LED's with secondry optics and IP 65 protection complete as specified and directed. Bajaj cat ref No. BCLST 20W LED code 169829 or equivalent in philips or Wipro as approved.

M&L for earthing with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanized earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC 1:3:6 type C1 pit with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 Nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work in any type of soil complete all as specified.

S&F MCB dustribution board SPN.240 volts, 8 ways powder coated, CRCA steel sheet constructed as per IS 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, eath bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F S&F MCBs as per load requirement ‘A’series of breaking capacity 10 KA, ISI marked incl required wiring connection with copper lugs of suitable size provided in MCB DBs of following ratings:

a) Single pole 6 to 16 amp.

(b) Double pole 32 amp.

(c) Four pole 63 amp.

Taking down carefully aluminium submain wiring with PVC surface conduit and making good disturbed surfaces complete.

nirman construction