ELECTRIFICATION WORKS FOR AIRCARGO AT CIAL

Amount

PART-A

HT EQUIPMENTS Modification of HT Panel Modification of one of the 11kV cubicle in the existing VCB panel inorder to make it suitable for functioning as the incomer to the new 1600 kVA, 11kV/433V 3 Ph, 50Hz, dry type, vector Dyn -11 Transformer. This includes SITC of numerical protection relays viz, O/C, E/F, suitable for 1600 kVA Transformer. The scope shall be inclusive of re-wiring the existing VCB panel with CT's and modification of protection, control and monitoring circuits and testing and commissioning of CT, relays etc. as required.

1600 KVA 11KV DRY TYPE TRANSFORMER Design, fabrication, supply, of DRY type indoor 1600 kVA, 11kV/433V 3 Ph, 50Hz, dry type, vector Dyn -11 Transformer, copper wound, laser scribed core, Class F insulation, indoor distribution Transformer with provision for fixing cooling fans in the base channel. The transformer shall have Delta on HV side and Star on LV side with off load tap changer range: + 5% to -5% in steps of 2.5%. The transformer shall also have suitable thermal relay (49W) and supply, fixing of neutral CT of 500/5A 10VA 5P10 on earthed star point with connector for connection to Earth Fault relay in HT/LT panel and Suitable for terminating busduct of 2500A. The transformer losses shall be as per latest ECBC standards.

Installation, testing and commissioning of DRY type indoor 1600 kVA, 11kV/433V 3 Ph, 50Hz, dry type, vector Dyn -11 Transformer including hoisting to the respective location, bolting the units, checking all the control and power cabling, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

PART - B

LT PANEL BOARDS AND BUSDUCT BUSDUCT Supply of 2500A ,415V, 50 kA, 50Hz AC TPN Sandwich Aluminum Bus Duct with 100% neutral Bus made out of 14 SWG powder coated and painted galvanised sheet steel IP54 enclosure, flexible end termination, fittings & accessories like elbows, offset sections, tees, reducers, adaptor boxes, flanges, flexible connections, expansion joints, ground strips, suitable supporting arrangement with metal suspenders/ brackets, provison for fixing 2 runs of 25x6mm Cu earth strip throughout the length of busduct etc. as required complete. (The rate shall be quoted for running meter and the elbows, bends, adaptor boxes are also measured under running meter and the rate shall be inclusive all associated accessories.) (The scope includes dismantling of existing 1600A busduct and taken back on buy back basis. The bidder shall deduct the buy back cost of existing busduct from the supply price of new 2500A busduct.)

Installation, Testing and Commissioning of 2500A ,415V, 50 kA, 50Hz AC TPN Sandwich Aluminum Bus Duct with 100% neutral Bus made out of 14 SWG powder coated and painted extruded Aluminium IP54 enclosure, flexible end termination, fittings & accessories like elbows, offset sections, tees, reducers, adaptor boxes, flanges, flexible connections , expansion joints, ground strips , suitable supporting arrangement with metal suspenders/ brackets ,provison for fixing 2 runs of 25x3mm Cu earth strip throughout the length of busduct etc. as required complete. (The rate shall be quoted for running meter and the elbows, bends, adaptor boxes are also measured under running meter and the rate shall be inclusive all associated accessories).

Installation, Testing and Commissioning of "MP - Cargo Village" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "MSB - Import Cargo" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "LIGHTING PANEL - Import Cargo" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "EQUIPMENT PANEL - Import Cargo" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "HVAC SB-1 (Import Cargo)" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "HVAC SB-2 - Import Cargo" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "HVAC Pump Panel - Import Cargo" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "SB - Metering" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "Metering Panel-1" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "Metering Panel - 2,3" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "300 kVAR CAPACITOR PANEL" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "ODP - Import Cargo" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

Installation, Testing and Commissioning of "LT Panel- GSE Building" including hoisting to the respective location, assembling of panels, lining up, bolting the units, checking all the control wirings, Calibration of all measuring instruments, precommissioning checks, all the tests at site as per standards etc complete and as detailed in technical specification.

PART - C

UPS AND ACCESSORIES Supply of 20 kVA, three phase input, Three Phase output, true on-line UPS System with 30 minutes back up, output isolation transformer, including all accessories, SMF batteries VRLA type with powder coated CRCA cabinet including all accessories such as cabling etc as required complete having following specification. RS485 Interface compatibility,Fully digital controlled based on DSP, Power factor corrected from end > 0.9, Pure sine wave output, Full time output voltage & frequency regulation, Auto Phase rotation fault compatible, Auto regulation of battery end voltage, Intelligent interface with LED/LCD display, Static bypass switch and manual by pass switch, Auto temperature compensation, Remote Management Interphase, Back up time 30 minutes at full load.

Installation, Testing and Commissioning including precommissioning checks of 20 kVA, three phase input, Three Phase output, true on-line UPS System with 30 minutes back up. The UPS shall be tested with actual load conditions.

PART -D

CABLES AND CABLING- CABLE SUPPLY Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3.5C 400 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3.5C 300 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3.5C 240 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3.5C 70 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3.5C 50 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 4C 35 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, unarmoured 4C 25 Sq.mm Copper conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 4C 16 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS,armoured 4C 4 Sq.mm Copper conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 2C 4 Sq.mm Copper conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3C 10 Sq.mm Aluminium conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 3C 4 Sq.mm Copper conductor cable conforming to IS 7098 (Part 1) amended upto date.

Supply of 1.1 KV grade XLPE insulated, PVC sheathed, FRLS, armoured 4C 2.5 Sq.mm Copper conductor cable conforming to IS 7098 (Part 1) amended upto date.

Cable Termination Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required. 3C X300 sq.mm.

Making end termination with brass compression gland and aluminium lugs for 3.5C 400 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 3.5C 300 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 3.5C 240 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 3.5C 70 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 3.5C 50 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 4C 35 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and copper lugs for 4C 25 Sq.mm Cu of XLPE insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 4C 16 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and Copper lugs for 4C 4 Sq.mm Cu of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and aluminium lugs for 3C 10 Sq.mm Al of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and Cu lugs for 2C 4 Sq.mm Cu of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and copper lugs for 3C 4 Sq.mm Cu of XLPE insulated and PVC sheathed / XLPE copper conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and copper lugs for 4C 2.5 Sq.mm Cu of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Making end termination with brass compression gland and copper lugs for 4C 1.5 Sq.mm Cu of XLPE insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Cable Laying Laying of one no. PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in recess/ surface/ cable tray/ wall/Open duct with saddles, clamps and all other accessories as required Above 120 sq. mm and upto 400 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. Above 120 sq. mm and upto 400 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable Upto 35 sq. mm (clamped with 1mm thick saddle) of 1.1 KV grade of following size on wall or surface as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp) of 1.1 KV grade of following size on wall or surface as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp) of 1.1 KV grade of following size on wall or surface as required.

Laying of one number PVC insulated and PVC sheathed armoured power cable Upto 35 sq. mm of 1.1kV grade of the following sizes in ground including excavation, sand cushioning , providing protective covering and refilling the trench etc. as required.

Laying of one number PVC insulated and PVC sheathed armoured power cable Above 35 sq. mm and upto 95 sq. mm of 1.1kV grade of the following sizes in ground including excavation, sand cushioning , providing protective covering and refilling the trench etc. as required.

Laying of one number PVC insulated and PVC sheathed armoured power cable Above 95 sq. mm and upto 185 sq. mm of 1.1kV grade of the following sizes in ground including excavation, sand cushioning, providing protective covering and refilling the trench etc. as required.

Laying of one number PVC insulated and PVC sheathed armoured power cable Above 185 sq. mm and upto 400 sq. mm of 1.1kV grade of the following sizes in ground including excavation, sand cushioning, providing protective covering and refilling the trench etc. as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable Upto 35 sq. mm of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable Above 35 sq. mm and upto 95 sq. mm of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable Above 95 sq. mm and upto 185 sq. mm of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable Above 185 sq. mm and upto 400 sq. mm of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable Upto 35 sq. mm of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable Above 35 sq. mm and upto 95 sq. mm of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable Above 95 sq. mm and upto 185 sq. mm of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable Above 185 sq. mm and upto 400 sq. mm of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable Above 185 sq. mm and upto 400 sq. mm of 1.1 KV grade of following size in the existing masonry open duct as required.

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable Upto 35 sq. mm (clamped with 1mm thick saddle) of 1.1 KV grade of following size on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable Above 35 sq. mm and upto 95 sq. mm of 1.1 KV grade of following size on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable Above 95 sq. mm and upto 185 sq. mm of 1.1 KV grade of following size on cable tray as required.

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable Above 185 sq. mm and upto 400 sq. mm of 1.1 KV grade of following size on cable tray as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 250 mm dia

Supply of 160MM PN8 PE 80 DN 160 grade suitable for laying as road crossing ducts by Horizontal directional Drilling method in complete as required. 160 mm dia

Conducting Horizontal Directional drilling and reaming it to adequate diameter required for housing 160mm PLB HDPE pipes / ducts at road crossing and laying of the ducts in the opening thus made. The rate should include the welding charges of HDPE ducts and also the cost for back filling the pit made at the starting and ending points.

Providing, laying and fixing following dia RCC pipe NP4 class (Heavy duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling, Road cutting and making good etc as required. 450 mm dia

Fabrication and Supply of 300 MM WIDTH X 50 MM DEPTH X 2 MM THICK Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required.

Fabrication and Supply of 600 MM WIDTH X 50 MM DEPTH X 2 MM THICK Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required.

Installation of 300 MM WIDTH X 50 MM DEPTH X 2 MM THICK Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with metal suspenders and all necessery accessories as required.

Installation of 600 MM WIDTH X 50 MM DEPTH X 2 MM THICK Ladder Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with metal suspenders and all necessery accessories as required.

Fabrication and Supply of 300 MM WIDTH X 50 MM DEPTH X 2 MM THICK Perforated Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required.

Fabrication and Supply of 600 MM WIDTH X 50 MM DEPTH X 2 MM THICK Perforated Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required.

Installation of 300 MM WIDTH X 50 MM DEPTH X 2 MM THICK Perforated Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with metal suspenders and all necessery accessories as required.

Installation of 600 MM WIDTH X 50 MM DEPTH X 2 MM THICK Perforated Type GI cable tray including horizontal and vertical reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with metal suspenders and all necessery accessories as required.

Supply, fabricating and installing MS items such as Tees/ angles/ channels etc. on floor/ ceiling/ wall including necessary civil work such as grouting, finishing etc. and painting with two coats of primer and two coats of synthetic enamel paint as required.

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Providing & fixing Fire Barrier mortar with minimum 2 hours fire rating when tested in accordance with BS 476 part 20 and UL 1479 for horizontal openings in fire rated floors or slabs and vertical openings in walls for passing service shafts. The service lines could be of various types like electrical cables trays, metal pipes, GI Ducts for AC, etc.The mortar shall have minimum hardened density of 0.8 g/cm3 and It should have a compressive strength of 2.9N/Sq mm . The product shall be Smoke & Air Seal and 30 years Age tested as per Dafstb and DIBT standards. The product shall be tested and approved by third party agencies such as UL and FM. The mortar should be tested in accordance with IEC 60068-2-57:1999-11 (Environmental Testing) as per Part 2-57: Test for Vibration-Time-history method and VERTEQII for seismic zone 4. The product shall bear the UL and FM approval logo on the packing where applicable.

PART-E

WIRING AND ACCESSORIES Supply of 20mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes, couplers, saddles etc as detailed in technical specification.

Supply of 25mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes, couplers, saddles etc as detailed in technical specification.

Supply of 32mm dia medium duty ISI marked PVC conduit including all accessories like bends, junction boxes, couplers, saddles etc as detailed in technical specification

Supply of 20mm dia corrugated good quality flexible PVC conduit along with adaptors and all other accessories as required complete.

Supply of 22mm ISI marked casing and capping including all accessories like elbows, tees, junction boxes etc as required complete.

Laying of 20mm dia PVC conduit along with accessories like PVC bends,couplers,junction box,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification.

Laying of 25mm dia PVC conduit along with accessories like PVC bends,couplers,junction boxes,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification.

Laying of 32mm dia PVC conduit along with accessories like PVC bends,couplers,junction boxes,fastners, iron staples/saddles/screws,in surface/ recess including cutting the wall/ceiling and making good the same in case of recessed conduit as required complete as detailed in technical specification.

Laying of 20mm dia corrugated good quality flexible PVC conduit along with adaptors and all other accessories as required complete.

Laying of 22mm ISI marked casing and capping along with accessories like elbows, tees, junction boxes, screws,in surface as required complete .

Supply of 25mm ISI marked casing and capping including all accessories like elbows, tees, junction boxes etc as required complete.

Laying of 25mm ISI marked casing and capping along with accessories like elbows, tees, junction boxes, screws,in surface as required complete .

Supply of 1.5sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Supply of 2.5sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Supply of 4sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Supply of 6sqmm FRLSH single core PVC insulated multistranded copper wire as detailed in technical specification.

Supply of 3C 1.5 sq. mm. FRLSH PVC insulated copper conductor stranded cable

Drawing of 1.5sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Drawing of 2.5sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Drawing of 4sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Drawing of 6sqmm FRLSH single core PVC insulated multistranded copper wire in existing conduit as detailed in technical specification..

Drawing of 3C1.5 sq. mm. FRLSH PVC insulated copper conductor stranded cable in existing conduit.

Supply of 6A modular type, one way switch with suitable front plate, metal box and all other accessories as required complete

Supply of 6A modular type two way switch with suitable front plate, metal box and all other accessories as required complete.

Supply of 6A modular type, 5pin plug socket with suitable front plate, metal box and all other accessories as required complete.

Supply of 16A modular type one way switch with suitable front plate, metal box and all other accessories as required complete.

Supply of 16A modular type, 5pin plug socket switch with suitable front plate, metal box and all other accessories as required complete.

Supply of 6A multistandard socket with suitable front plate front plate, metal box and all other accessories as required complete.

Supply of surface or recess mounted type 15A SP weatherproof one way switch with IP66 enclosure and all other accessories as required complete

Supply of blanking plate with suitable front plate, metal box and all other accessories as required complete.

Supply of modular stepped type electronic 2module fan regulator with suitable front plate, metal box and all other accessories as required complete.

Supply of 6A, 1 way bell pushbutton station with IP 65 protection and all other accessories as required complete.(Make:Schneider Cat No: WS226PBGY or equivalent approved make.)

Supply of 230V, one module buzzer along with back box, front cover and all other accessories as required complete.

Fixing 6A modular type one way switch with suitable front plate & metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of 6A modular type two way switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of 6A modular type, 5pin plug socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of 16A modular type one way switch with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of 16A modular type ,5pin plug socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of multistandard socket with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required , making good the surface etc. as required complete.

Fixing of surface or recess mounted type 15A SP weatherproof one way switch with IP66 enclosure including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of blanking plate in existing switch box as required complete.

Fixing of modular stepped type electronic fan regulator with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of bell push with suitable front plate &metal box on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

Fixing of 230V, one module buzzer alongwith backbox, front cover on surface or in recess including inter connections cutting the wall if required, making good the surface etc. as required complete.

PART -F

MCBs AND MCB DISTRIBUTION BOARDS Supply of 12 way double door, single pole and neutral, sheet steel, powder coated, MCB distribution board, 240 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required (IP 42/43 type).

ITC of of 12 way double door, single pole and neutral, sheet steel, powder coated, MCB distribution board, fixing required number of SP/DP MCBs, RCCBs, Blanking plates,cable entry box, etc complete with all other accessories including cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 4 way (8 + 12) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for single phase out goings and separate cut-out for 4P RCCB and 4P MCB for incoming etc. as required and as per specification (IP 42/43 type).

ITC of 4 way (8 + 12) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, fixing required number of TP/FP MCBs, RCCBs, Blanking plates,,cable entry box, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 8 way (8 + 24) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for single phase out goings and separate cut-out for 4P RCCB and 4P MCB for incoming etc. as required and as per specification (IP 42/43 type).

ITC of 8 way (8 + 24) double door, three pole and neutral, sheet steel, powder coated, horizontal MCB distribution board, 415 volts, fixing required number of TP/FP MCBs, RCCBs, Blanking plates,cable entry box, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 8 way (8+ 24), double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required .

ITC of 8 way (8+24) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of SP/TP/FP MCBs, RCCBs, Blanking plates,cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 6 way (8+ 18), double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required .

ITC of 6 way (8+18) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of SP/TP/FP MCBs, RCCBs, Blanking plates,cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 4 way (8+ 12), double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board 415 volts, complete with tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required .

ITC of 4 way (8+12) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of SP/TP/FP MCBs, RCCBs, Blanking plates,cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 8 way (8 + 24), double door, three pole and neutral, sheet steel, powder coated, Vertical MCCB distribution board (LOAD BANK) 415 volts, complete with , tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for upto 160A, 4P, MCCB as incomer.

ITC of 8 way (8+24) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of TP/FP MCBs, RCCBs/MCCBS, Blanking plates, cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 4way (8 + 12), double door, three pole and neutral, sheet steel, powder coated, Vertical MCCB distribution board(LOAD BANK) 415 volts, complete with , tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required suitable for upto 160A, 4P, MCCB as incomer.

ITC of 4 way (8+12) double door, three pole and neutral, sheet steel, powder coated, Vertical MCB distribution board, 415 volts, fixing required number of TP/FP MCBs, RCCBs/MCCBS, Blanking plates ,cable entry box,steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of cable entry adapter box for Horizontal 8Way TPN DBs including all accessories as required complete.

Supply of cable entry adapter box for Vertical, TPN DBs including all accessories as required complete.

Supply of cable entry adapter box for Vertical, TPN DBs with MCCB as incomer including all accessories as required complete.

Supply of 6 amps to 32 amps rating, 240 volts,Single pole “C” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 415 volts,Triple pole “C” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 240 volts,Single pole “D” curve, miniature circuit breaker.

Supply of 40 amps to 63 amps rating, 415 volts,three pole “C” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 415 volts,triple pole “D” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 415 volts, Four pole “C” curve, miniature circuit breaker.

Supply of 6 amps to 32 amps rating, 230 volts, Double pole “C” curve, miniature circuit breaker.

Supply of 40 amps to 63 amps rating, 415 volts, four pole “C” curve, miniature circuit breaker.

Supply of single pole blanking plate for distribution boards .

Supply of 63A, four pole, 415 volts, MCB isolator.

Supply of 40A, four pole, 415 volts, MCB isolator.

Supply of 32A, four pole, 415 volts, MCB isolator.

Supply of 100A, four pole, 415 volts, MCB isolator.

Supply of 125A, four pole, 415 volts, MCB isolator.

Supply of 125Amp,16KA, FPMCCB in existing DB

Supply of 100Amp,16KA, FP MCCB MCCB in existing DB

Supply of 2 pole 25 amps. (240 Volts), 30mA sensitivity. residual current circuit breaker (RCCB).

Supply of 4 pole 25 amps. (415 Volts), 30mA sensitivity. residual current circuit breaker (RCCB).

Supply of 4 pole 25 amps. (415 Volts), 100mA sensitivity. residual current circuit breaker (RCCB).

Supply of 4 pole 40amps. (415 Volts), 100mA sensitivity. residual current circuit breaker (RCCB).

Supply of 4 pole 63amps. (415 Volts), 100mA sensitivity. residual current circuit breaker (RCCB).

Supply of sheet steel enclosure suitable for independent mounting of DP MCB.

Fixing of sheet steel enclosure on surface/ recess along with fixing of DP MCB complete with connections,with all other accessories as required complete.

Supply of sheet steel enclosure suitable for independent mounting of FP MCB/ ISOLATORS .

Fixing of sheet steel enclosure on surface/ recess along with fixing of FP MCB/ ISOLATORS complete with connections,with all other accessories as required complete.

Supply of 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps “C” curve, SP, MCB+RCCB, in sheet steel enclosure with chained metal cover for the socket out let .

ITC of 20 amps, 240 volts, SPN industrial type, socket outlet, alongwith 20 amps “C” curve, SP, MCB+RCCB, on surface or in recess, inter connections, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 32 amps, 240 volts, SPN industrial type interlocked switched sockets and surface mounting box IP 44 socket outlet, with stright plug along with 32 amps “C” curve, SP, MCB in complete.

ITC of 32 amps, 240 volts, SPN industrial type, interlocked switched sockets and surface mounting box IP 44 socket outlet, with stright plug along with 32 amps “C” curve, SP, MCB on surface or in recess, inter connections, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

Supply of 32 amps, 415 volts, TPN+E industrial type, socket outlet, interlocked switched sockets and surface mounting box IP 44 socket outlet, with stright plug alongwith 32 amps “C” curve, TPN, MCB, in complete .

ITC of 32 amps, 415 volts, TPN+E industrial type, socket outlet, interlocked switched sockets and surface mounting box IP 44 socket outlet, alongwith 32 amps “C” curve, TP, MCB, on surface or in recess, inter connections, steel fasteners etc complete with all other accessories including MS supports or cutting the wall if required ,finishing ,making good the same etc complete.

PART- G

LIGHT FIXTURES AND FANS Supply of symmetric LED Highbay with high pressure die cast aluminium housing,along with driver, system wattage maximum of 80 Watts, lumen output of luminaire greater than or equal to 10800 ,power factor > 0.95,rated life of L70 @ 50,000 hours. system efficacy greater than 135 lumen/watts, CRI >70, 4 kV internal surge protection, including all necessary accessories as required complete.Make:- Wipro LH21-122-060-57-XX or Philips BY515P LED100S 5700 NB PSU GR or equivalent approved makes

Supply of indoor surface mounted LED Batten with Extruded aluminium and Polycarbonate Diffuser ,along with driver,system wattage of maximum 20 Watts, lumen output of luminaire greater than or equal to 2000, power factor >= 0.9,rated life of L70 @ 50,000 hours, system efficacy greater than or equal to 110 lumen/watt, CRI >80, cool day light and including all the necessary accessories as required complete.Make:- Cat No: LL24-311-XXX-57-HE- or Philips BN100C LED20S-6500 PSU L120 GR S4 or equivalent approved make.

Supply of indoor decorative surface mounted LED Batten with Extruded Polycarbonate housing and Polycarbonate Diffuser along with driver,system wattage of maximum 10 Watts,lumen output of luminaire greater than or equal to 1000, power factor >= 0.9,rated life of L70 @ 50,000 hours, system efficacy greater than 100lumen/watt, CRI >80, cool daylight and including all the necessary accessories as required complete.Make:- Cat No: Wipro LL20-111-XXX-65-NE3 or Philips BN021C LED12S 6500 PSU GR orequivalent approved makes.

Supply of 40W High efficient Industrial LED batten surface/wall mounted Specially designed extruded Aluminium housing with PC diffuser. In-built electronic driver duly wired up to terminal block. IP40, CRI >80, Power factor>0.95, THD<10%, Surge protection 2kV, 50000 burning hours as per L70 Criteria, Luminaire lumen ≥ 100 lm/W,lumen output of luminaire greater than or equal to 4000 (Make:Wipro LL24-541-XX-57-XX or Equivelent approved make)

Supply of 2x2 LED fixture with housing made of metallic CRCA powder coated body and a high efficiency diffuser along with driver,system wattage of maximum 36 Watts,lumen output of luminaire greater than 3600 lumens, power factor > 0.9, rated life of L70 @ 50,000 hours, system efficacy greater than 100 lumen/watt, CRI >80, with suitable driver and including all necessary accessories as required complete.Make:- Cat No: LT LUMINOX X03657R000 or Philips RC380B LED36S 6500 PSU or Wipro CRCO10R038HP57G1L5 or equivalent approved make.

Supply of indoor surface mounted Industrial LED mid bay luminaire, system wattage of maximum 40 Watts, power factor > 0.9,rated life of L70 @ 50,000 hours, system efficacy greater than 115 lumen/watt, ,lumen output of luminaire greater than 4600 lumens CRI >70, and including all the necessary accessories as required complete. Wipro Model No. LE09-571-XXX-57-XX or equivalent approved make.

Supply of LED recess mounted down light made of die cast aluminium, along with driver,system wattage of maximum 12 Watts, CCT- 5700K with lumen output of luminaire greater than 1200 lumens, power factor > 0.9, rated life of L70 @ 50,000 hours, system efficacy greater than 100 lumen/watt, CRI >70, and including all necessary accessories as required complete. Make:- Wipro LD06X-151-XX-57-XX or Philips DN296B LED12S 6500 PSE or equivalent approved make.

Supply of LED recess mounted down light made of die cast aluminium, along with driver,system wattage of maximum 18 Watts, CCT- 5700K with lumen output of lamp greater than 1800 lumens, power factor > 0.9, rated life of L70 @ 50,000 hours, system efficacy greater than 100 lumens/watt, CRI >70 and including all necessary accessories as required complete.Make:- Cat No: Wipro LD06X-221-XX-57-XX or DN296B LED20S 6500 PSE or equivalent approved make.

Supply of 10w LED Bulkhead fitting with die cast aluminium housing, PC diffuser and IP66 Protection suitable for operation on 230V 50Hz AC, wall / ceiling including giving connections with required length of 16/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire and making good the surface as required. (Make:LW07-141-XXX-57-G1 or equivalent approved make)

Supply of 400 mm size full metal body wall mounting oscillating type fan having three speed control, oscillation control at bottom and suitable for operation on single phase 230 volt, 50Hz AC supply complete with continuous duty motor, chrome plated front and rear gaurds and all accessories as required complete. (Make crompton or equivalent approved make).

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019),THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supply of 225 mm sweep, 900 rpm light duty exhaust fan in plastic body with self opening louvers working on 230 V AC supply complete with all accessories as required. (Crompton Brisk Air or equivalant approved make)

Supply of 600 mm size wall mounting oscillating type air circulator with regulator suitable for operation on single phase 230 volt, 50Hz AC supply complete with continuous duty motor, chrome plated front and rear gaurds and all accessories as required complete.(Make: Almonard or equivalent approved make)

Supply of 450 mm sweep,900 rpm heavy duty exhaust fan in metal body with louvers working on 230 V AC supply complete with all accessories as required. (Crompton EXHD 450 -6-1 or equivalant approved make)

Supply of 16 feet diameter, 70 rpm HVLS fan with 5 Aluminium blades, Geared Motor IP 55 with helical gear with gear oil type motor with IE2 efficiency of rating 1.5 HP, 415 V , 3 phase AC, CAT 5 communication cable, with individual digital control panel and VFD controller along with SS Safety cable & minimum 4 no's SSGuy Wires and all accessories as required complete.

ITC LIGHT FITTINGS AND FANS Installation, testing and commissioning of pre-wired, LED fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLSH PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of LED down lighter fittings on false ceiling with all mounting accessories as required complete including interconnections using 3 runs of 1.5 sqmm FRLSH PVC insulated stranded copper conductor as required.

Installation, testing and commissioning of LED fittings with chain and copper wiring - Installation testing and commissioning of prewired fluorescent fittings of all types including LED complete with all accessories, lamps etc. on false ceiling including supplying and fixing of GI chain and hook arrangement, upto 60cm length, and wiring using 3 runs of 1.5 sqmm FRLSH PVC insulated stranded copper conductor cable as required.

Installation, testing and commissioning of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of the above fan, making good the damage, connections, testing & commissioning etc as required.

Installation, testing and commissioning of High bay/LED/ FLOOD type fittings on wall/Column/truss/false ceiling using suitable MS clamps, nuts, bolts/ 20mm heavy duty GI chain/ pipe (upto 50cm)etc including connections with 3C 1.5 Sq.mm PVC insulated flexible copper conductor cable as required.

Installation, testing and commissioning of Wall fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation, testing and commissioning of 16 feet diameter HVLS fan including power cabling from VFD panel to fan,fixing of control panel, guy wire fixing etc and all accessories as required complete.

Numbering of ceiling fan / exhaust fan/ fluorescent fitting as required.

PART - H

EARTHING AND SAFETY EQUIPMENTS Supply and installation of all the materials required for maintenance free earthing system including 3 mtrs length,17.2mm dia or above 250 microns molecularly copper bonded steel rod with stainless steel connectors and fasteners for connecting earth strip, earth enhancing compound (12.5 kg mineral compound / 22.6 kg low resistivity graphite compound) and providing masonry enclosure with heavy duty CI cover plate of 300X300 mm having locking arrangement.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing GI/Cu strip/wire on surface or in recess for connections etc. as required.

70 mm X 10mm GI

25mm X 6mm GI

25mm X 3mm Cu

25mm X 6mm Cu

10 SWG Cu

6 SWG Cu

2 SWG Cu

Supplying and laying G.I/Copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

70 mm X 10 GI

25mm X 3mm Cu

25mm X 6mm GI

10 SWG Cu

6 SWG Cu

2 SWG Cu

Supply and providing ISI marked electrical 3.3 kV grade anti-skid synthetic insulated mat as per IS:15652.for the following sizes.

2mx1mx2.5mm thick

Supply of First aid box

Supplying of Rubber hand gloves suitable for 11 KV.

Supply and fixing anodised aluminum glass framed shock treatment chart.

Supply and fixing single line diagram, schematic diagrams etc. of A0 size including lamination etc. as required complete on wall.

Supply and fixing single line diagram, schematic diagrams etc. of A1 size including lamination etc. as required complete on wall.

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

PART- I

LIGHTNING PROTECTION Supply and fixing of 8 mm Aluminum Round Conductor as horizontal air terminal for roofing sheet with the required mounting clamps , cross connectors, expansion piece and other accessories required as per IEC 62305-3 and as required complete.

Supply and Fixing of 8 mm Aluminum Round Conductor as vertical down conductor with the required mounting clamps , cross connectors, T connectors, expansion piece and other accessories required as per IEC 62305-3 and DIN EN 50164-2 suitable for installation on surface as needed and as required complete.

Providing and Fixing of Test Joint, suitable to fix 8 mm Aluminium conductor to 32 X 6 GI strip.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

PART- J

EXTERNAL LIGHTING Supply of 7 Meters Octogaonal Pole made of hot dip galvanised GI sheet 70mm top diameter, 130 mm bottom diameter thickness 3mm base plate dimensions of 200x200x12 mm suitable for wind speed as per IS 875 Part III single arm bracket 0.5mt including connector foundation bolt4 nos fixed in RCC foundation and junction box etc. complete . Along with LED street light with inbuilt driver,system wattage maximum of 60 watts, power factor >0.9, IP 65 compliant, CRI>70, lumen efficacy of 110lumen/watts. The pole shall be with bracket and built in GI control box of same material with service door coated with three stage painting processThe pole shall have provision of connecting the earth wire including all necessary accessories as required complete. (Luminairie Make: Wipro LR02-671-XXX-57-XX or Philips BRP062 LED 68 CW SLC S1 PSU equivalent approved make)

Installation, testing and commissioning of surface mounting octogonal street light poles 7 Mtrs long with 0.5 Mtrs overhang single arm Bracket suitable for mounting 1 No. street light fixture. Along with LED street light inbuilt driver, system wattage maximum of 60 watts including all necessary accessories and civil works for foundation as required complete. Note:Incoming and outgoing cable at termination box shall be terminated with glands properly.

Supply, of LED Street Lighting luminaire of IP66 protected,pressure die cast aluminium housing body with optimal heat sink, with system wattage less than 60W with rated life of L70 @ 50,000 hours, CRI greater than or equal to 80 & with system lumensgreater than 6600 and system efficiency greater than or equal to 110.The Light fitting shall be with allrequired accessories suitable for mounting in (48-60)mm OD pole arm.The luminaire should meet all the technical specifications as mentioned.Make: wipro LR02-671-XXX-57-XX or Philips BRP062 LED 68 CW SLC S1 PSU or equivalent approved make.

Installation, testing and commissioning of LED Street Lighting luminaire of IP66 protected, pressure die cast aluminium housing body with optimal heat sink, with system wattage less than 45 W. The Light fitting shall be with all required accessories suitable for mounting in (48-60)mm OD pole arm.The luminaire should meet all the technical specifications as mentioned. Make: wipro LR02-501-XXX-57-G1 or equivalent approved make.

PART- K

ADDITIONAL CIVIL WORKS 2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.1.4 Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete.

12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand).

Imperial Engineering Company

National Electric Co

HELSA ELECTRICALS PVT LTD

Fathima Engineering Co. Pvt. Ltd.