Supply, Laying, Erection, Testing and commissioning of 220kV 1Cx1200 sq. mm D/C (2*(3+0)) Cu. conductor U/G cable laying from prop. 220kV M/C cable termination Monopole Loc. No. 1C/0 to 220kV Khoraj SS with 4.20RKM UG Cable for M/s Maruti Suzuki India Limited (MSIL)

Estimated Cost of laying of two equal lengths of FOAC (Fiber Optic Approach Cable) ( DWSM - Dual window single mode, 48F) - with installation hardware like ties / clips /

cleats, conduits, HDPE ducts, supports, fittings, accessories, Fiber Optic Distribution Panel(FODP), FOAC joint box (Continuous length of FOAC is preferred, however due

to limitation of laying continuous long length of FOAC, one joint may be provided only if required) etc with required arrangement to lay along side of U/G cable -

(Annexure-B1 (Supply) & B2 (Erection))

Estimated Cost (Supply Part) (Annexure-B1)

Sr.No. Name of Line FOAC Single Length (DWSM 48F) Nos. of such sigle length of FOAC Total length of FOAC (DWSM

(meter) required 48F) (meter)

1 220kV Khoraj S/S to M/s Maruti Suzuki India Ltd Line 4300 2

Estimated Cost (Erection Part) (Annexure-B2)

Sr.No. Name of Line FOAC Single Length (DWSM 48F) Nos. of such sigle length of FOAC to Total length of FOAC (DWSM

(meter) be laid 48F) (meter)

1 220kV Khoraj S/S to M/s Maruti Suzuki India Ltd Line 4300 2

Following points are important from work execution perspective, same may please be noted.

i) Fiber optic approach cable (FOAC) shall be laid with 220kV cable system strictly as per approved method of construction i.e MOC.Continuous length of FOAC is preferred, however due to

limitation of laying continuous long length of FOAC, one joint may be provided only if required

ii) Two to Three rings of extra loop length shall be kept buried underground at foot of both end termination tower after laying FOAC cable with 220kV cable as per MOC.

iii) FOAC cable length remain outside and above the ground level shall be 2 times the height of each termination tower at both end. Each run of FOAC cable coming out after laying in underground

section should be brought up to third cross arm of termination tower after passing it through HDPE pipes and properly tying up with tower. Also, each run of FOAC cable shall be terminated in

individual joint box on each termination tower.

iv) Balance length of each FOAC cable (i.e. Approximately half of tower height) after bringing out the FOAC cable above from ground level and up to third cross arm of termination tower, it shall be

managed in rings properly with fixing clamp arrangement to hold up it on end termination tower.

v) As per standard GETCO format of "End to End test.pdf" , after laying FOAC cable, each length shall be tested for end to end test using power meter and OTDR. Original copy of Test report duly

sealed and signed with date, name & designation of testing person, executing contractor and witnessing officer one each from telecom as well as TR/Const. nominated from respective EE(Telecom)

and EE(TR)/EE(const.) respectively, shall be submitted to under signed & one copy to respective telecom unit, invariably without fail

vi) Only after getting clearance on validity of test report submitted to this office, filed officer will take further necessary action on commercial part.

vii) DRS (Data requirement sheet) and drawing approval shall be taken for FOAC & joint box before kick starting any erection activity. The work executing contractor must have to do

correspondence on eamil to concern EE (Const.) with copy to project & engineering department, corporate office, GETCO for necessary concurrence and intimation about to start erection/laying.