PROVN OF STORAGE SHED NEAR BLDG NO. DY-10 OF 39 INF DOU AND OTHER SANCTIONED WORKS AT ALHILAL MIL STN

Amount

SCHEDULE 'A' PART-I:- Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed .

Excavating over areas, n exc 1.5m deep and getting out getting out in hard/dense soil complete all as specified and directed.

M&L plain cement concrete 1:3:6 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete, complete all as specified and directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6, complete all as specified and directed.

Returning, filling in (soil), including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n. exc. 50 mtr and depositing where directed at a level n. exc. 1.5 mtr above the starting point, complete all as specified and directed.

M&L reinforced cement concrete, 1:2:4 (Nominal Mix), type B-1(using 20mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams, roof beams, bases for columns, etc.; basement slabs, under reamed piles and mass concrete etc, complete all as specified and directed.

M&L reinforced cement concrete 1:2:4 (Nominal Mix), type B-1(using 20mm graded crushed stone aggregates) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies,canopies, deck slabs ,complete all as specified and directed.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc, complete all as specified and directed.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, andings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc, complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirmaing to TMT bars, complete all as specified and directed.

S&F mild steel TMT bars 6mm to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to TMT bars, complete all as specified and directed.

S&F mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality confirming to TMT bars, complete all as specified and directed.

M&L rendering 10mm thick plaster on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surface fair and even complete all as specified and directed.

M&L rendering 15mm thick cement plaster 1:4, on stone masonry surfaces other than fair face of brick work or on one side lathing and finishing the surface even and smooth w/o using extra cement complete all as specified and directed.

M&L plain cement concrete M-10, nominal mix, 1:3:6 type C-1, using 20mm graded mechanically crushed stone aggregate, 75mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

M&L hardcore of broken stone or boulders of guage n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

M&L 75mm thick plain cement concrete, 1:3:6 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in sub base of floor and path etc, complete all as specified and directed.

M&L 25mm thick plain cement concrete, 1:2:4 (Nominal Mix), type B-0 (using 12.5 mm graded crushed stone aggregates) as in sub base of floors finished rough surface to receive floor finishes, complete all as specified and directed.

M&L non-skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of mortar in cement plaster 1:4, complete all as specified and directed.

M&L glazed ceramic coloured tiles 450 mm x300 mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick backing coat CM 1:4 to receive tiles, complete all as specified and directed.

S&F solid PVC door frame of size 50x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, S&F in opening as per specification & drawing shown in SSR Part-II, complete all as spfd and directed.

S&F factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement S&F in frames at site as per specification and drawing shown in SSR Part-II, complete all as specified and directed.

S&F 150mm long aluminium handle, cast type, anodised complete all as specified and directed.

S&F 150mm size aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S&F 100 mm size butt hinges,medium weight, mild steel cold rolled, complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of walls and applying thtee coats of white wash, complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of ceiling and applying three coats of white wash , complete all as specified and directed.

M&L preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F 3mm thick figured glass pin head type and glazing with oil putty in squares n.exc. 0.50 sqm in each pane, complete all as spfd and directed.

S&F rotational moulded polyethylene water storage tank 500 Ltrs capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, complete all as specified and directed.

S&F bib tap, cast copper alloy with crutch or butterfly handle, fancy type,chromium plated screwed down, screwed for iron pipe, 15 mm bore, complete all as specified and directed.

S&F pillar tap, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe 15 mm bore, complete all as specified and directed.

S&F angle valve PTMT alloy fancy type, chromium plated screwed down for high pressure screwed down for 15mm bore with crutch or butterfly handle both ends screwed for iron pipe or union etc, complete all as specified and directed.

S&F 20mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed.

S&F vitreous china, wash hand basin, (white) of size 550mmx400mm including brass CP waste coupling 32mm dia with long screwed shank and fly nuts, PVC medium grade 32mm dia waste pipe, chain and plug, porcelain stopper , PVC connection 15mm dia, 450mm long with brass CP nuts and washers at both ends, complete all as specified and directed.

S&F vitreous China squatting pan of pattern“long pan”, size 580 mm including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device (excluding flushing cistern and flush pipe), complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring fixed in wall, ceiling, floors etc, complete all as specified and directed.

S&F 110mm bore PVC (SWR) vent cowl complete all as specified.

S&F PVC (SWR) PVC (Singal T) equal and unequal 110 mm bore complete all as specified and directed

S&F PVC (SWR) PVC (Singal T) equal and unequal 75 mm bore complete all as specified and directed.

S&F 10 Litres capacity PVC symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle & PVC flush pipe, fixed in position and connecting complete all as specified and directed

S&F brass chromium plated tubular towel rail, 20mm dia, 60 cm long, CP with a pair of brackets, fixed to wall with CP brass screw and PVC rawl plugs, complete all as specified and directed

S&F CP grating doom 125mm dia with waste hole of PTMT (Minimum weight 40gms), complete all as specified and directed.

M&L, reinforced cement concrete, M-25 (Design Mix), type B-1(using 20mm graded crushed stone aggregates) as in foundations, including footings, plinth beams, etc.; basement slabs, under reamed piles and mass concrete etc, complete all as specified and directed.

M&L, reinforced cement concrete, M-25 (Design Mix), type B-1(using 20mm graded crushed stone aggregates) as in Columns, pillars, piers, posts and struts etc, complete all as specified and directed.

M&L, reinforced cement concrete, M-25 (Design Mix), type B-1(using 20mm graded crushed stone aggregates) as in Beams, chajjas, cantilevers, bressummers, lintels over 1.5m span etc, complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof cover/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof cover/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

M&L for mild steel work as plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, etc., and similar small articles conforming to Fe- 410W, Gde-E-250, complete all as specified and directed.

M&L100mm thick plain cement concrete 1:3:6 (Nominal Mix), type C-2 (using 40mm graded crushed stone aggregates) as in sub base of floor and path etc, complete all as specified and directed.

M&L 40mm thick plain cement concrete 1:2:4 (Nominal Mix), type B-1 (using 20mm graded crushed stone aggregates) as in flooring etc,finished even and smooth without using extra cement complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L machine Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10mm thick backing coat in CM 1:4, complete all as specified and directed.

S&F mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framin (Beams, tee, angle, channel or any flat section) including distance pieces, cleats etc conforming to Fe-410-W,Gde-E-250,quality 'A' , complete all as specified and directed.

M&L preparation of new surface of steel of any description, over 10cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

M&L PCC, 1:3:6 (Nominal Mix) type C-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc, complete all as specified and directed.

M&L mild steel framed work such as in grills, gates and gratings with ends of bars shouldered or reveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar works, conforming to Fe-290, Gde E-165, complete all as specified and directed.

Supply and fixding expanded metal, not exc 4.0 kg per sqm cut to length, bent to shape required and tying with and including anneled mild steel wire not less than 0.9 mm dia or fixing with galvanised steel staples complete all as specified and diredted.

Excavation in trenches n exc 1.5mtr wide and n exc 1.5mtr in depth for foundation etc or for shafts,wells,cesspits,manholes,pier holes,etc,n exc 10sqm on plan and getting out any type of soil, complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161- 1979 grade St.-240 complete all as specified and as directed.

Excavation in post holes (or similar holes) each n.exc. 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to a distance not exceeding 50m, in any type of soil and making good surfaces, complete all as all as specified and directed.

Surface dressing not exceeding 15 cm deep in hard/dense soil, complete all as specified and directed.

M&L Pavement quality control concrete design mix (M-40) using crushed stone aggregates having minimum field flexural strength of 40 Kg/Sq.cm in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less, pavement laid to level , gradient & camber including necessary form work, complete all as specified and directed. NOTE:-cement required for achive flexural is more than 400 kg/cum than no extra amount will be paid for excess use of cement.

M&L forming Constraction(dummy) joints for 65 mm deep x 10 mm wide filled with sealing compound Grade A, complete all as specified and directed.

M&L forming construction joints 30 mm deep X 10 mm wide filled with sealing compound grade 'A', complete all as specified and directed.

S&F steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

S&Fsteel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

SCHEDULE 'A' PART-II:- Point wiring for one light point controlled by one way switch with cable of size 1.5sqmm copper conductor cable multi strand PVC insulated FRLS (unsheathed) concealed type, drawing in and including PVC conduit 25mm dia having wall thickness not less than 2mm with sunk cast iron/pressed steel terminal boxes made out of 1.2mm thick sheet including one coat of red oxide primer on internal and external surface including cover plate for required module for mounting switches, sockets, regulators etc controlled by one, one way switch, including 1.5sqmm PVC insulated copper conductor continuous earth wire complete all as specified and directed. Note: Wiring shall be done using colour code.

All as per the description of Serial item No 74 above but for 3 pin switch socket outlet 6 Amp on same board with other switches, complete all as specified and directed.

All as per the description of Serial item No 74 here-in-before but for 3 pin socket outlet 6 amp independent board complete all as specified and directed.

All as per the description of Serial item No 74 here-in-before but for 3 pin socket outlet 15/16 amp independent board with cable of size 2.5 sqmm in point wiring and 1.5 sqmm in continuous earth wire complete all as specified and directed.

S&F switch piano flush button, 6 Amps, single pole one way complete all as specified and directed.

S&F switch piano flush button, 16 Amps, single pole one way complete all as specified and directed

S&F socket outlet 2 in 1, 3 Pin 6 Amps flush type complete all as specified and directed .

S&F socket outlet 2 in 1 3 pin, 6 and 16 amp flush type all as specified and directed

S&F ceiling rose 3 terminal bakelite 65mm x50mm surface type, PVC/Polycarbonate, isolated body, complete all as specified and directed .

S&F lamp holder, insulated body, with back plate for batten fitting with LED Lamp 3 W, complete all as specified and directed.

S&F LED tube light box type batten fitting suitable for 1x20W, 4 FT, 6500 K complete with LED tube rod, fixed complete to wall/ceiling and PVC round block (02 Nos) of suitable size etc provided complete incl provn of flexible wire 3 core of size 23/.0076 from ceiling rose to connector with flexible pipe of suitable size of all complete all as specified and directed. Make -Crompton Cat Part No DMLN1LT8-16 and LED tube & Cat Part No LT8-20-865-2 or equivalent in makes as mentioned in Appx 'C'.

S&F1x10W LED light fitting mirrror type with high out put diffuser 2 feet long 220V AC decorative type with driver holder and LED lamp ,fixed to wall/ceiling with PVC round/square block(02 Nos) of suitable size including connection complete all as specified and directed.

S&F exhaust fan AC single phase 240 V of size 300 mm sweep (PVC body) with louvers shutter and making hole in brick/stone wall if required at site and making good disturbed complete incl provn of flexible wire 3 core of size 23/.0076 from ceiling rose to exhaust fan complete all as specified and directed

Supply and fixing of ceiling fan AC single phase 240 V of size 1200 mm sweep five star rating with all accessories complete incl provn of flexible wire 3 core of size 23/.0076 from ceiling rose to ceiling fan all as specified.

S&F LED Bulk Head 10W with pressure plastic housing with clear prismatic diffuser, high efficient LEDs IP66 complete all as specified and directed.

Supply, fixing, connecting and testing electric water heater storage type 25 ltrs capacity vertical type, BEE 5 star rated complete with stainless steel water tank and all safety devices such as thermostat, pressure release valve, NRV and air release valve etc complete all as specified and directed.

Supply and fixing PVC water connection pipe 15mm size with PTMT nuts of length 450 mm for inlet & outlet connection (cold & hot water ) complete all as specified.

S&F 15mm bore steel water tubing, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work etc, complete all as specified and directed.

Supply and fix 15mm bore stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union etc complete all as specified.

Supply and fix bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified.

S&F sheet metal enclosures distribution board single pole and natural 4 way with 200 Amps rated bus bar 240 Volts, single door type complete all as specified. Note:- distribution board and MCB's should be same make.

Supply and fix MCB SP 240 volts, 10kA, capacity 6-32 Amps 'B' series all as specified.

Supply and fix MCB SPN 240 volts, 10kA, capacity 32 Amps 'C' series all as specified.

Supply and fix MCB SPN 240 volts, 10kA, capacity 40- 63 Amps 'C' series all as specified.

S&F 1100 volts grade heavy duty cable PVC insulated aluminium stranded conductor, served with inner sheathed of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular in section of cross sectional area 10sqmm twin core complete all as specified and directed.

S&F sub main wiring with two single core PVC insulated, FRLS unsheathed multi stranded copper conductor cable confirming to IS 694-1990 of size 6Sqmm (nominal area) and draw in & including PVC conduit of size 25mm dia with all fittings such as Tee, connector pieces, L-junction etc on joints, not less than 2 mm thick and continuous PVC insulated single core copper conductor multi stranded unsheathed 6 Sqmm as earth wire complete all as specified and as directed. Note: Two single core cable and one No earth wire shall be measured together as one length.

Earthing with galvanized steel earth plate electrode 60cmx60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the earth plate not less than 1.5 mtr deep below normal ground level, connected to 4mm dia galvanized iron wire as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel complete with 15mm dia light grade protection pipe, 20mm dia GI light grade watering pipe with funnel including char coal dust, salt, PCC 1:2:4 in pit with precast RCC M-15 cover reinforced with XPM not less then 4.00 Kg per sqm including necessary earth work in any type of soil, removal of surplus soil to a distance not exc 50m, returning filling in complete as shown in electrical plate No 3 of SSR Part-I (2009), and connected to earthing test point all as specified or indicated, including testing on completion. NOTE: The rates for earthing includes the cost of earth lead and protection pipe upto 7.50m length.

Supply and fix LED bulb 3 watt, warm white 2700K, 230 volts complete all as specified.

Supply and laying or fixing or passing through pipe or laid in trenches, 1100 Volt grade heavy duty cable XLPE insulated, armoured electric cable with aluminium conductor ,cross-sectional area 10sq.mm, 2 core,complete all as directed.

S&F 40mm bore galvanised iron, light grade (ISI marked) laid in trenches / fixed on wall/poles etc for protection of cable complete all as specified and as directed.

Excavation in trenches in any type of soil not exc. 1.5m wide and not exc. 1.5m deep for laying cables, foundation of poles, stays etc and getting out, complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers n.exc 25cm thick, complete all as specified and directed.

Removal of excavated material to be distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5m above the starting point, complete all as specified and directed.

M&L sand cushioning to under ground cable with a layer of sand 8 cm before laying the cable and 15 cm after laying the cable (10 cm punned thickness above the top of the upper most cable, total 18 cm), complete all as specified and directed.

M&L sub class “B” brick, old size, brick covering laid dry, flat, transversally along the length of cable on sand cushioning, with width equal to length of the brick complete all as specified and directed.

M/S THAKUR ENTERPRISES

M/S SAI ENGINEER

M/S Bharmouri Construction

VIVEKA ENTERPRISES