SPECIAL REPAIR TO BUILDING NO P-119 AT NIAT, NAVAL BASE KOCHI

Amount

Dismantling of single layer Mangalore pattern or similar tiles in roofing laid dry including ridge tiles laid bedded and jointed in CM complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling timber scantlings under 40 Sqcm in section for unframed work in fillets, rails, posts, rafters, purlins etc, in unframed works complete all as specified and as directed.

All as per item No 3 here-in-before but over 40 Sqcm in section.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed.

Dismantling of battens for tiles shingles etc of any size including tilting fillets, spaced at distance exc 15 cm complete all as specified and directed ..

M&L for IInd class HW in wooden scantling clean sawn for unframed work in any position with nails complete all as specified and directed complete all as specified and directed.

All as per item No 7 here-in-before but except timber. Note: The item dismantled vide item No.4 hereinabove shall be re-used.

M&L 2nd class H.W. plain fillets square, rectangular or triangular in section bull nosed, splayed chamfered or rounded on one edge or face in sectional area exc. 13 Sqcm and not exc. 25 Sqcm fixed with nails complete all as specified and directed.

All as per item No 9 here-in-before but except fillets. Note: The item dismantled vide item No.3 hereinabove shall be re-used.

M&L for IInd class HW sectional area exc 5 and n.exc 15 Sq cm clean sawn battens at 30 cm centres for Mangalore pattern tiles complete all as specified and as directed.

All as per item No 11 here-in-before but except timber. Note: The item dismantled vide item No.6 hereinabove shall be re-used.

M&L preparation of surfaces and creosoting to new tiles battens of any size and spacing (measured overall on one side only, spaces not deducted) with two coats of creosote oil complete all as specified and directed.

All as per item No 13 here-in-before but one coat on old surfaces.

S&F for 0.63mm thick class 3 Galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 275 complete all as specified and directed.

All as per item No 15 here-in-before but fixing only Note: The item dismantled vide item No.2 hereinabove shall be re-used.

M&L for Mangalore pattern roof tiles, interlocking at side joints, laid dry complete all as specified and as directed.

All as per item No 17 here-in-before but fixing only Note: The item dismantled vide item No.1 hereinabove shall be re-used.

M&L for ridge or hip tiles to suit Mangalore pattern of roofing tiles, bedded and jointed in cement mortar 1:6 complete all as specified and as directed.

M&L for IInd class hard wood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 to 20mm thick and fixed with 30mm laps complete all as specified and as directed.

Taking down eaves gutters and rain water pipes of any size or any pattern including all fittings

S&F 180 mm dia of half round ready made eaves gutter of pressure rating 6 Kg/cm2 of approved make including necessary fitting like bend WC, clamp/ MS clips etc complete all as specified and as directed.

S&F 150 mm dia of PVC (SWR) pipe single socketed in any length with rubber joints fixed on walls complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for Vitrified tiles 600mm x 600mm x 8 to 10 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

All as per item No: 25 here-in-before but as in skirting over and including 10 mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm tk screed bed of CM 1:6 all as specified and as directed.

M&L for Glazed ceramic tiles in vertical surface 600 x 300x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade over and including 10 mm thick rendering CM 1:4 all as specified and as directed.

Taking down cement plaster on brick/ concrete walls incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 finished even and smooth without using extra cement for internal faces of walls complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:4 over a backing coat of 10mm thick 1:4 using WPC finished even and smooth without using extra cement for external faces of walls complete all as specified and as directed.

Supply only integral water proofing compound.

M&L for preparation of newly plastered internal wall surfaces and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered surface of wall and applying two coats of distemper oil emulsion (Asian paint Royale or equivalent of other make given in list of make) over a coat of alkali resistant primer and 3mm thick wall care putty complete all as specified and as directed. Note :- Application of paint, primer and wall care putty shall be done through authorised applicator of paint manufacturer.

M&L Preparation of newly plastered wall surfaces and applying two coats of Apex Ultima Protek of Asian paint or equivalent of Berger/Nerolac/Dulux over a coat of anti fungal primer duly applied through authorised company applicator using modern tools and techniques of approved make complete all as specified and as directed.

Taking down Chowkhats or frames not exc. 1.5 Sqm each, but with shutters (without taking off shutters from the frames) complete all as specified and as directed.

Taking down chowkats or frames (wooden / steel/ PVC) of area exc 1.5 sqm but n exc 4 Sqm without taking off shutters from the frame complete all as specified and directed.

S&F for powder coated aluminium frame work for doors, openable / sliding windows, ventilators and partitions with one or more rebates including joining cleat for fixing etc. Complete all as specified (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) (minimum thickness of powder coating 50 micron) complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 3.0 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per SSR specification & drawing complete all as specified and directed

S & F factory made solid panel PVC door shutter 28 to 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, including tarring with a coat of tar and sanding the back or surfaces contacted with concrete or mortar complete all as specified and directed.

S&F 2nd class hard wood framed, panelled factory made shutter 40 mm thick (two panel) with lock rail and panel of 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

S&F 2nd class HW Glazed and skeleton shutters of thickness 35mm , open rebated & prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, fitted with cut and mitred beads for securing glass, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

M&L for M.S Hold fasts of FI 25 x 3 mm confirming to Fe290 Gde E 165 fixed in and including plain cement concrete 1:3:6 type C1 using (20mm graded crushed stone aggregate) including treated with tar or coal tar black paint complete all as specified and directed

M&L Preparation of new wooden surface of any description over 10cm in girth or width and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

M&L for 100 mm size, butt hinges medium weight cold rolled mild steel.

M&L for 200mm long aluminium anodized barrel tower bolt of extruded section complete all as specified.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Dismantling wall and ceiling boards or insulation boards/slabs/ blankets, any thickness, including cover fillets.

S&F aluminium snap grid false ceiling on frame work of angle 25x25x2 mm, Main TEE 38x25x1.5 mm and cross TEE 25x25x1.4 mm and size of grid 605x605 mm with hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.50 mm dia, 40 mm long with and including provn of 4mm thick Non asbestos fibre cement building boards fixed to aluminium frame work with screws including preparation of new ceiling surfaces and applying two coats of oil emulsion distemper over a coat of primer including necessary scaffolding complete all as specified and directed.

S&F in repairs vitreous China wash down water closet pan (pedestal pattern), white incl plastic water closet seat, black, closed pattern with flat bottom, cover and mild steel chromium plated or aluminised hinging device, fixing bolts, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float & handle incl brackets, PVC connections 15mm size with PTMT nuts of length 600 mm and Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern and 15mm bore stop cock complete all as specified and directed. Make of EWC:- Parryware (cat No.C844A white) or Cera (Cat No.3131 white) or Hindware (Cat No.92082 White)

S&F in repairs vitreous China squatting pan, ‘Orissa’ pattern, size 630 x 450 mm white, with integral foot rests incl PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle incl brackets, PVC connections 15mm size with PTMT nuts of length 600 mm and flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern and 15mm bore stop cock complete all as specified and directed.

S&F in repairs 630 X 450 mm Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand including 15mm bore fancy type Brass CP pillar tap, PVC connection 600mm long and 15mm bore stop cock complete all as specified and directed. Make of WHB:- Parryware cat No. C844T or Johnson cat No. P5115MPW or Jaquar Cat No. CNS-WHT-809 Make of Pillat tap:- Parryware cat No. T0802A1 or Johnson cat No.T2601C4 or Jaquar Cat No. ARI-39011.

S&F in repairs 32 mm Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed. Make:- Parryware cat No. T3203A1 or Johnson cat No.T0060C or Jaquar Cat No. ALD-769L300 x 190.

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. Make:- Parryware cat No. T6003A1 or CERA cat No.F5004106 or Jaquar Cat No.CAN-CHR-1131N.

S&F in repairs Tubular towel rail, 20mm dia, D type, 60cm long, stainless steel complete all as specified and as directed. Make:- Parryware cat No. T6401A1 or Jaquar Cat No.ACN-CHR-111SM.

S&F in repairs vitreous china urinals coloured half stall type including all fittings complete all as specified and as directed. Make :- Parryware cat No. T0578 White or Johnson cat No.P0519PW or Jaquar Cat No. URS-WHT-13261.

S&F in repairs vitreous chinaware partition for urinal of size 310 x 700 mm all as specified and as directed.

S&F in repairs Push tap high pressure suitable for urinals complete all as specified and as directed.

S&F in repairs CP urinal spreader for 15 mm bore fixed with urinal including CP pipe complete all as specified and as directed.

S&F in repairs 75 mm PVC (SWR) floor trap plain with grating incl jointing with solvent cement complete all as specified and as directed.

Demolition and breaking up 100 mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 100 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends single socketed in any length, with rubber rings complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends single socketed in any length, with rubber rings complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) pipes vent cowl complete all as specified and as directed.

S&F 4mm dia Plain mild steel wire, galvanised class 3 in detached work such as mosquito nets / cloth hanging wire and fixing to straining bolts, hooks, eyes, etc. complete all as specified and directed.

S&F Mild steel rag or lewis bolts (dia of neck 25mm), screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, n exc 15cm long complete all as specified and directed.

M&L for 18/19 mm thick Pre-laminated particle board, exterior grade pre-laminated one side with decorative choice lamination & another side balancing white lamination, fixed with screw complete all as specified and as directed.

Extra over rates of particle boards for external teak wood lipping 6 mm thick fixed with nail for 18/19 mm thick boards complete all as specified and as directed.

M&L for 40mm dia cupboard knob fixed with nut screw and washer, fixed as in repair complete all as specified and directed.

S&F 50mm brass lock , 4 lever, grade I for drawer.

Demolition of cement concrete (un-reinforced) in ground floors & pavings n exc 15 cm thickness (below / above ground level) complete all as specified and as directed.

M&L for hardcore of gauge n exc. 63 mm, using broken stone broken or boulders, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for providing 75mm thick cement concrete, Type C1, 1:3:6 (using 20mm graded stone aggregate) for plinth protection complete all as specified and as directed.

M&L Bitumastic gola, with 80/25 bitumen and coarse sand mixture. 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces complete all as specified and as directed.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth , for foundation etc for laying of cable, shaft wells, cesspits manholes, pier holes, etc n.exc 10sqm on plan and n exc 1.5m in depth and getting out in soft/lose soil complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc. 25cm. deep with approved soil obtained from excavation

Removing excavated material to a distance n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Demolition and breaking up of 150 mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M&L for 150mm dia reinforced concrete pipes class NP2 with collars complete all as specified and directed.

M&L for plain cement concrete Type D-2, 1:4:8 (using 40mm graded crushed stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes (150mm bore pipe) after the pipe are laid and tested complete all as specified and directed.

M&L for precast re-inforced cement concrete 1:2:4 Type B1 using 20 mm graded crushed stone aggregate as in cover slabs (for manholes etc) and similar articles with plain face, set in cement mortar 1:6. all as specified and directed. Note:- Reinforcement shall be measured and paid separately.

M&L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in coping on walls, finished even and fair incl necessary form work complete all as specified and directed.

M&L for TMT bars 6 to 8 mm dia cut to length, bent to shape required, including cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips quality conforming complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, or securing with clips quality conforming complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry with solid blocks, Type C1 (1:3:6) using 20mm graded stone aggregate, exc. 10cm in width and setting in cement mortar 1:6 complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement and sand mortar 1:4 finished even and smooth without using extra cement.

S&F Hume pipe septic tank 25 users capacity including necessary earth work in soft/ loose soil, PCC 1:3:6 in bed concrete with accessories like AC vent pipe, cowl manhole cover etc including connecting to the sewer line complete all as shown in drg No.TD/A/57 sheet 1/1 including removal of old septic tank and connected works complete all as specified and as directed by Engineer-in-Charge.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

M&L for providing 75mm thick cement concrete, Type E2, 1:5:10 using 40mm graded stone aggregate as in sub base of floor / hard standing etc complete all as specified and as directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20mm thick screed in CM1:6 complete all as specified and as directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for, Complete all as specified and as directed.

M&L for PCC 1:4:8, Type D2 using 40 mm graded stone aggregate in foundation bed to drain Complete all as specified and as directed.

Supply and laying, 25mm outer dia high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings, fixed to walls/floors /ceiling or concealed in wall and jointed with yellow solvents cement including taking down old unserviceable CPVC/GI tubing complete all as specified and directed.

Supply and laying, 20mm outer dia high pressure CPVC pipes SDR-13.5 & plain CPVC SDR 11 fittings, fixed to walls/floors /ceiling or concealed in wall and jointed with yellow solvents cement including taking down old unserviceable CPVC/GI tubing complete all as specified and directed.

S&F in repair, 15mm bore stop valve / angle valve half turn cast copper alloy chromium plated fancy type for fixing with CPVC pipe, complete all as specified and as directed. (Make : Model No: F2004201 of Cera or Jaquar cat No. CON-CHR-059KN or Prayag cat No. 7610)

S&F in repair 25mm bore CPVC Ball brass valve with high pressure with polythene ball of size 6" dia and fly nut including taking down the old unserviceable one complete all as specified and as directed.

S&F in repair 20mm bore CPVC Ball brass valve with high pressure with polythene ball of size 6" dia and fly nut including taking down the old unserviceable one complete all as specified and as directed.

S&F in repairs hand shower (health faucet) ABS body with 15 mm dia 1 Mtr long SS braided rubber hose pipe and wall hook complete all as specified and as directed.(Make : Model No: F8030102 of Cera or equivalent model of other manufacturers from the list)

S&F in repair, 15mm bib tap quarter turn with flange and aerator cast copper alloy chromium plated fancy type short body for fixing with CPVC pipe, complete all as specified and as directed. (Make : Model No: F2004151 of Cera or equivalent model of other manufacturers from the list)

S&F in repair, swivel overhead shower (minimum weight 40grams) of PTMT any colour with shower arm (minimum weight 40 grams) 15mm size, 195mm long with bend of 45 degree with flange for fixing with CPVC pipe, complete and all as specified and as directed. (Make : Model No: F7020104 of Cera or equivalent of prayag/hind ware)

S&F in repair, 15 mm bore, concealed stop cock half turn with sliding flange chromium plated fancy type, complete all as specified and as directed. (Make : Model No: F2002362 of Cera or equivalent model of other manufacturers from the list)

S&F in repair, PVC connection 16mm outer dia, 450mm long for cold water with brass union on both sides to suit 15mm dia GI pipe complete all as specified and as directed.

S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of 2000 litre capacity including making holes for inlet and outlet including taking down old tank complete all as specified and directed .

S&F in repair 25mm dia float valves of synthetic (PVC) high pressure with polythene ball of size 6" dia and fly nut complete all as specified and as directed.

S&F in repair Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position of 200 litre capacity including making holes for inlet and outlet including taking down old tank complete all as specified and directed .

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M&L , point wiring using approved colour coding as per IS (Red, Black and Green for single phase circuits) with 1.5 sqmm nominal cross sectional area, copper conductor unsheathed FRLS cable 1100 Volts grade ISI-694 marked with valid CML No. single core multistranded cable in and including medium grade concealed PVC conduit not less than 20mm dia and accessories ISI marked with valid CML No (IS-9573-1983 for conduits and IS: 3419: 1976 for conduit accessories) and including 2 mm thick MS sheet/ pressed steel sunken boxes depth not less than 50mm (earth dolly) duly painted with two coats of anti corrosive paint / aluminium paint over a coat of red oxide primer internally and two coats of black bituminous paints over a coat of red oxide primer externally covered with 3 mm thick plastic laminated sheet cover for fixing of switches sockets and fan regulators etc including 1.5 Sqmm nominal cross sectional area PVC insulated copper conductor unsheathed FRLS cable single core multistranded cable as earth continuity wire for one light / fan point controlled by one switch, all as specified and as directed.

All as per item No. 119 here in before but one 5 pin 5 Amps socket outlet controlled by one switch on same Board.

All as per item No. 119 here in before but one 5 pin 5 Amps socket outlet controlled by one switch on independent Board.

All as per item No.119 here in before but with 2.5 sqmm (copper conductor) cable for wiring and 2.50 sqmm cable as earth continuity conductor for one 6 pin 16 Amps switch socket outlet on independent board

S&F Switch piano flush type 5 Amps single pole, one way,230 volts all as specified and as directed.

S&F Switch socket combination, 5 pin, 5 Amps ISI marked, flush type all as specified and as directed.

S&F Switch socket combination,6 pin, 16 Amps ISI marked, flush type multi purpose all as specified and as directed.

S &F ceiling rose surface bakelite,65x50mm two/three terminal 240 volts all as specified and as directed..

Supply and fix in repair ceiling fan 1200 mm sweep, 5 star rated white colour including canopy 2 Nos, hanging rod and accessories complete all as specified and directed. Make:- Model ES-40 of Havells or equivalent model of Crompton greaves / Bajaj.

S&F stepped type electronic fan regulator flush socket type suitable for 1200 mm sweep fan all as specified and as directed.

S&F tube light fitting 1 x 20 W with T8 LED tube with aluminium extrusion heat sink for optimum performance with high luminous efficiency and batten prewired suitable for use with LED tube with concealed accessories complete all as specified and as directed. Make: Philips cat part No. TMC501 P 20W 1XT LED P3241 + ESSENTIAL LED TUBE 20W 1200 MM 20W 865 T8 or equivalent model of other manufacturers from the list as approved by GE.

Supply & Fix LED street light fittings 35/36 Watt 240 Volts , IP-65 class of protection with accessories including provision of connecting cable and including provn of GI pipe for fixing on wall complete all as specified and directed. Make : Crompton cat part No LSTS-36-CDL-M or equivalent model of other manufacturers from the list as approved by GE.

Supply and fix wall mount type LED bed lamp 1 x 3 W, 230V including 1 x 3 watt LDC white 30 K lamp and connected accessories, flexible copper wire from ceiling rose to light fitting terminal complete all as specified and directed. Make : Philips Cat Part No.48042 / 30 / 31 or equivalent model of other manufacturers from the list as approved by GE.

Taking down old DBs from existing position including MCB's all as specified and as directed.

S&F Sheet metal enclosure SPN for DB's when MCB's to be used 4 way double door with 200 Amps bus bar fixed flush to wall complete all as specified and as directed.

S&F Sheet metal enclosure SPN for DB's when MCB's to be used 8 way double door with 200 Amps bus bar fixed flush to wall complete all as specified and as directed.

S&F Sheet metal enclosure SPN for DB's when MCB's to be used 12 way double door with 200 Amps bus bar fixed flush to wall complete all as specified and as directed.

S&F Sheet metal enclosure TPN for DB's when MCB's to be used 4 way double door with 200 Amps bus bar fixed flush to wall complete all as specified and as directed.

S&F MCB TPN 63 Amps 415 volts 10 KA, ' B ' series all as specified and as directed.

S&F MCB SP 6 to 32 Amps 240 volts 10 KA, 'B ' series all as specified and as directed.

S&F MCB SPN 63 Amps 240 volts 10 KA, 'B ' series all as specified and as directed.

Taking down sub main wiring of any size and type complete

M&L for sub main wiring with two runs of single core 4 Sqmm (FRLS) multistranded copper conductor PVC unsheathed cable drawn through and including PVC conduit medium grade of not less than 20 mm dia concealed in wall/floor for sub main connection including one run of 4.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. Note : Three runs of 4 Sqmm (FRLS) copper conductor and one run of PVC conduit shall be measured as one unit length.

M&L for sub main wiring with four runs of single core 6 Sqmm (FRLS) multistranded copper conductor PVC unsheathed cable drawn through and including PVC conduit of not less than 20 mm dia concealed in wall/floor for sub main connection including 2 runs of 6.0 Sqmm (FRLS) PVC insulated multistranded unsheathed copper conductor used as a earth wire to common earth and connection to earth dolly complete all as specified and directed. Note : Six runs of 6 Sqmm (FRLS) copper conductor and one run of PVC conduit shall be measured as one unit length.

Supplying, laying, testing and commissioning XLPE insulated PVC bedded galvanized steel strip armored electric cable 1100 volt grade heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area 16sqmm 4 core including taking down of old cable Complete all as specified and directed .

M&L in repairs for earthing complete with galvanised steel earth plate electrode 60 cm x 60cm x6 mm thick, buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meters below normal ground level, connected to galvanised iron wire 4.0mm dia upto length 7.5 mtr by means of bolts, nuts and washers of galvanised steel all as shown in electrical plate No. 3 of SSR part I, connected to earthing test point complete all as specified and indicated including testing on completion including taking out old, earthing complete. Note:- The rate is deemed to be inclusive of the cost of complete earth work in any type of soil. PCC 1:3:6 type C-1 for chamber,RCC 1:2:4 type B1 for precast cover slab 50 mm thick, reinforcement 8 mm TMT bars @ 150 mm c/c both way, necessary form work, handle, charcoal dust 20mm dia GI med grade for watering and 15mm dia GI med grade earth lead protection pipes with funnel and wire mesh complete all as specified and directed..

SUKU CONSTRUCTIONS

Albert Rebello and Company

M/s ANTONY THOMAS AND CO

AMRITH ENGINEERS