PROVISION OF WIRE MESH FOR EIGHT STATIC WATER TANK (SWT) AT AWS AREA AND FACTORY AREA OF NAD ALWAYE UNDER AGE B/R ALWAYE

Amount

Supply and fix steel tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade ST-240 complete all as specified and as directed.

Supply and fix plain channels/ angles/ bars square cut or notched Fe-410- W (Grade-E-250) quality-A ordinary and counter sunk forming holes, with riveted, bolted or welded attachment complete all as specified and as directed.

Supply and fix aluminium alloy wire mesh 4mm nominal dia of wire and average width of aperture 20mm and fixed with aluminium wire staples complete all as specified and as directed.

Supply and fixing mild steel rag bolt or lewis bolt, screwed one end with hexagonal or square nut and washers, other end enlarged and jagged or lewised, not exceeding 15 cm long, 12mm dia neck all as specified and as directed.

Supply and fix powder coated aluminium frame for windows, doors & ventilators with one or more rebates including joining cleats for fixing etc. complete all as specified and as directed.

Supply and fix powder coated aluminium window and ventilators shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No), hinges type B-21 100mm long (2 No) suitable handle (1 No) complete all as specified and as directed. Note: Glass panel and wire mesh shall be measured and paid separately.

Supply and fix Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) grade Fe-410-W(Gde E-250) complete all as specified and as directed.

Supply and fix hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 with bracing aluminium mesh to lower skeleton complete all as specified and as directed.

Material and labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

Demolition of cement concrete, unreinforced, in ground floor and paving not exceeding 15cm thickness above or below ground level complete all as specified and as directed.

Material and labour for plain cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate in foundations, filling and mass-concrete complete all as specified and as directed

Supply and fixing 2mm dia galvanised steel chicken wire mesh complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate complete all as speciifed and as directed.

Material and labour for 15mm thick rendering in cement mortar 1:4, on fair faces of brick work/ concrete surfaces using water proofing compound @3% by weight of cement finished even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound shall be measured separately.

Supply only liquid water proofing compound complete all as specified and as directed.

Material and labour for RCC design mix M-30 in foundaions including rafts, footings, foundation beams, plinth beams, bases for columns etc, basement slabs and mass concrete all as specified and as directed.

Use and waste of formwork to sides of concrete footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc rough finished surfaces complete all as specified and as directed.

Material and labour for TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending, spirally hooping for columns hooking ends and binding with mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

Material and labour for TMT bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length bent to shape required including cranking, bending, spirally hooping for columns hooking ends and binding with mild steel wire annealed not less than 0.9mm dia complete all as specified and as directed.

Material and labour for applying 3 coats of white wash to newly plastered surfaces including preparation of new surface of wall complete all as specified and as directed.

ZOOM ENTERPRISES (BID ID -3143734)

St George Engineering Works (BID ID -3142769)

M/s Antony Kallarakkal (BID ID -3143863)

SOORYA ASSOCIATES (BID ID -3143974)

Kuriako Mathai and company (BID ID -3150520)

ELSOL ENGINEERS (BID ID -3150577)

LALA CONSTRUCTION (BID ID -3138266)

M/S V ASSOCIATES (BID ID -3144460)