SPECIAL REPAIR TO BUILDING No P90 P93 AND P94 AT AIR FORCE STATION BHOWALI UNDER GE AF BAREILLY

Amount

Demolition of cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

Dismantling of floor hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store & rubbish of the premises complete all as specified and directed.

M & L 25 mm thick cement concrete type B-0, 1:2:4 (12.5mm graded stone aggregate) as base coarse for floors complete all as specified and directed.

M & L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in cm 1:6 complete all as specified and directed.

M&L non skid ceramic tiles 7-8mm thick coloured (Square/rectangular) area of each tiles exceeding 0.18 sqm but n exc 0.36 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L non skid ceramic tiles 7-8mm thick coloured (Square / rectangular) joint free area of each tiles exceeding 0.18 sqm but n exc 0.36 sqm in vertical surface such as dado/lkirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing coat in cment mortar 1:4 complete all as specified and directed.

M&L non skid ceramic tiles 7-8mm thick coloured (Square / rectangular) area of each tiles exceeding 0.11 sqm but n exc 0.18 sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

S&F glazed ceramic coloured tiles in vertical surface 350 x 450 x 7 mm thick set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M & L for 75 mm thick cement concrete 1:3:6 type C-2, using 40 mm graded crushed stone aggregate as in plinth protection laid to slop of 1:12, finished surface even and fair without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

M & L for rendering /Screed bed, 15mm thick in CM 1:3 with WPC (mixed as per manufacturer's instruction) complete as specified and directed. Note :- WPC shall be Measured and Paid separately under respective item of BOQ.

M&L for preparation of plaster surfaces /RCC roof surfaces and applying one coat of bituminous primer @0.30 Ltr/sqm complete as specified and directed.

M & L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm icluding cleaning surfaces etc complete as in sunken portion complete as specified and directed.

M&L for polythene film, black 50micron laid in floors/DPC complete as specified and directed.

M & L for providing plain cement concrete 1:5:10, type E-2 (using 40 mm graded crushed stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Removing demolished material to a distance exc.1.5km but nexc. 5km & depositing where directed as in any type of soil complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for brick work with Sub class 'B' brick straight or curved on plan exc. 6m mean radius built in cm 1:6 complete all as specified& as directed by EIC.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L for rendering 15mm thick in cm (1:4) on fair faces of brick work or concrete surfaces finished & even and smooth complete all as specified and directed.

M&L 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces of wall and finished even and fair without using extra cement complete all as specified and directed.

Supply only Intergral Waterproofing compound complete all as specified and directed.

M&L for preparation on new plaster surfaces and applying two coats of Oil bound Distemper over one coat of 1 mm thick wall care putty and a coat of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified & directed.

M & L surface preparation of old and applying one coats of cement base paint on plasterred surface complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of Oil Bound Distemper over one coat of 1-2 mm thick wall care putty and a coat of primer complete all as specified and directed.

M&L prepration of old decorated ceiling surfaces (plastered or unplastered) including cornices, plasters etc. by brooming down with steel wire brushing and applying one coat of white wash on ceiling all as specified and directed

Dismantling of water tank exc. 250 Litre but not exc. 500 Litre capacity complete all as specified and directed.

S & F 500 Litre capacity rotational moulded polyethylene water storage tanks three layered (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part – I and hoisted, fixed in position complete all as specified and directed.

S & F 20 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gram) complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified & directed.

Taking up or down 15 mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified & directed.

S&F 20mm dia steel tubes medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge.

S&F 15mm dia steel tubes medium grade galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engr-in-Charge.

Supply and fixed gun metal globe valves or gate valve, 20 mm dia, with iron wheel head ,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S & F in repairs 15mm Angular stop valves,fancy type and chromium plated cast copper alloy, screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or unions complete all as specified and directed.

S& F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed.

S & F in repair 15mm bib tap cast copper alloy fancy type chromium plated with crutch or butter fly handle screwed down high pressure for iron pipe or brass ferrule etc. fixed complete all as specified and directed.

S&F in repairs Wash basins, vitreous china (flat back or angle back type) any size, including cutting for & pinning in ends of brackets or erecting stand but including of fixing of supply & waste pipe 450x300mm size complete all as specified and directed.

S & F in repair 15mm pillar tap CP cast copper alloy with capstan head screwed down high pressure with or without lettered hot or cold with long shank and fly nuts fancy type complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but n exc 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutter of any description exc. 1.00 Sqm & nexc. 2.00 Sqm each complete all as specified and directed.

Taking down shutters of any description n exc 1 Sqm each, complete all as specified and directed.

S & F pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc., steel ventilator with top hung shutter including hinges, steel peg stay complete all as specified and directed.

S&F for 35mm thick, 2nd Class HW (SAL), plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified and directed.

M&L glazed & skeleton shutters 35mm thick 2nd class Hard wood open rebated & prepared to receive glass, gauge etc. edges of framaing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc. sized of members of shutter with three number of pannels complete all as specified and directed.

M&L 19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F of external teak wood lipping 6mm thick fixed with nails for 18/19mm block board or veneered particle board complete all as specified and directed.

M&L 2nd class hard wood plain fillets, square, rectangular or tringular in section, clean sawn secured with nails or brads, sectional area exc 3 & n exc 6 sq cm complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 95mm made out of 5mm wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheetreinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid PVC Door shutters 30 mm thick (styles )consisting of frame made out of MS tube for top and bottom rails, mild steel frame shall be covered with wood grain printed PVC 'C' channel having a PVC Sheet strip of 20mm with stuck inside with solvent cement for stiles and wood grain printed PVC Sheets for top rail , lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; Panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitabledecorative PVC sheet beading of 10mmx10mm , and joined together with solvent cement at site as per specification and drawing complete all as specified & directed

S & F 100mm butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised , type B-21 complete all as specified & directed

S & F 150mm aluminium handles cast type anodised complete all as specified & directed

S & F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified & directed

S & F butt hinges 100 mm long medium weight cold rolled mild steel complete all as specified & directed

S&F 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F 300mm ordinary rat rail pattern springs including roller and roller plate complete fixed in repairs for steel chowkats welding complete all as specified and directed.

S & F 125mm hasp & staple, safety type, aluminium anodised with mild steel hinge pin inluding bolt to hinge plate sixed with screws complete all as specified and directed.

S&F Aluminium section powder coated of colour as approved openable sliding type three track window/ventilators with sliding shutter and frame with aluminium section of size including 5 mm thick tinted glass and mosquito proofing net as indicated below complete all as specified & directed (i) Frame section 92.00 X 31.75X 1.30MM (ii) Shutter top bottom and side rails 40.00 X 18.00 X 1.29MM (iii) Glass 5 mm thick one side reflective glass and other side visible of with rubber gasket with clips and hold fast 04 nos for each window including necessary handles, tower bolt etc. complete (iv) Aluminium grill 4 to 5 mm dia design no. DG - 102 make DECO grill or design no AL - 103 make fixed to aluminium section 50X20X1.5 mm in existing opening. (v) stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.4mm fixed with tinted tacks or galvanized wire staples complete all as specified and directed..

S&F Anodised aluminium frame powder coated for door, window, vetilators and partition with one or more rebates including joining cleat for fixing etc.complete all as specified and directed.

S&F 4 mm thick figured glass pin headed type,and glazing fixed in aluminium ventilator square n.exc 0.5 sq. m in each complete all as specified and directed.

M & L for providing plain cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

S & F galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of new or previously untreated steel and iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old wooden surfaces not otherwise described, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

S&F in repair 20 mm dia mild steel coloured PVC coated curtain rod complete all as specified and directed.

M&L for mild steel coloured L type brackets including PVC designer dom for curtain rod and plug suitable for fixing complete all as specified and directed.

Dismantling of bricks (laid flat or on edge) or brick tiles bedded and pointed in any mortar as in floors, channels, kerbs, aprons on roof including cleaning for refixing etc complete all as specified and directed. complete.

M&L for roughening existing roof surface and provide PCC 1:2:4 type B-1 (Using 20mm graded stone agg) as in levelling course in terracing or padding over roof complete all as specified and directed

M&L for cleaning of old roof slab surfaces including sweeping clean &washing down with water to remove dust & providing water proofing treatment with polymeric standard water proofing membrane complete all as specified and directed including following provisions: (a) M & L for plaster 10mm thick in CM 1:3 with WPC (b) M&L preparation of plaster surfaces /RCC roof surfaces and applying one coat of bituminous primer @0.30 Ltr/sqm (c) M&L applying bitumen @1.20kg/sqm of grade 85/25 (d) Supplying and laying modified polymeric water proofing membrane super thermo lay STP OR IWL or equivalent of any other standard approved manufcturer 3mm thick of weight not less than 3.00kg /sqm reinforced with polyester non woven fabric weight not less than 150gm/sqm center core including coping on the surfaces with torch application of membrane with 10cm over laps as required all complete all as specified and directed. NOTE :- THE WORK SHALL BE GOT EXECUTED THROUGH EXPERT TEAM OF MANUFACTURER OR AUTHORISED APPLICATOR OR MANUFACTURER.

M & L 40mm thick brick tiles laying over bedding layer 20 mm screed bedded in Cement mortar (1:4) and tiles joints grouted flush in Cement mortar (1:3) mixed with 5% of cruide oil by weight of cement complete all as specified and directed.

Fixing only 40 mm thick brick tiles over bedding layer 20mm screed bedded in Cement mortar (1:4) and tiles joints grouted flush in Cement mortar (1:3) mixed with 5% of cruide oil by weight of cement complete all as specified and directed.

M&L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition and breaking up drain pipes of 100 mm bore (salt glazed stoneware, AC or reinforced concrete) set in cement mortar complete all as specified and directed.

M & L for cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in bed to drain pipes of 150 mm bore including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

M & L for 150 mm bore salt glazed stoneware drain pipes grade 'A' laid in trenches and jointed in cement sand mortar 1:1 with spun yarn complete all as specified and directed.

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting out in any type of soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance exc. 1.50 KM and n exc 5.00 KM and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

Supplied and fixed in repair vitteous chinaware EWC padestal type closet with white seat & cover with flat bottom with hinging device complete all as specified and directed.

S & F in repairs water closet vitreous china squatting pan ‘Orrisa’ pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti-syphonic pipe etc. with and including setting the trap and pan in lime concrete bedding (one lime, two sand or surkhi and 5 aggregate) minimum 150 mm thick alround and finished just below level of rim of pan to receive the floor finishes complete including making good floor complete all as specified and directed.

S & F in repair polymer white (polypropylene Delrin and ABS) low level flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, flush pipe, brass screws, handle etc complete having BIS description mark with IS: 7231 with and including 32 mm bore PVC flush pipe of suitable length complete all as specified and directed.

Dismantling of 100 mm bore cast iron or reinforced concrete drain pipe, jointed in cement mortar and taking out of trenches, if required complete all as specified and directed.

S & F in repair 100 mm bore cast iron soil, waste and vent pipe, sand cast, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches complete all as specified and directed.

S & F in repair 75 mm bore cast iron soil, waste and vent pipe, sand cast, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn laid in trenches complete all as specified and directed.

S & F in repair 100 mm bore cast iron soil, waste and vent pipe, sand cast, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn fixed to walls complete all as specified and directed.

S & F in repair 75 mm bore cast iron soil, waste and vent pipe, sand cast, in any length, with or without ears, with cement joints in cement sand mortar 1:1 with spun yarn fixed to walls complete all as specified and directed.

S & F in repair 100 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S & F in repair 75 mm bore cast iron bend (any radius), diminishing piece or taper (larger bore measured) complete all as specified and directed.

S & F 100 mm bore cast iron bend (any radius) with duck’s foot or heel rest complete all as specified and directed.

S & F 100 mm bore cast iron branch piece, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and directed.

S & F stack clamp made of 50 mm X 5 mm flat iron and 16 mm dia round iron stay including nut bolts and securing ends of stay to wall or roof suitable for 100 mm bore pipe complete all as specified and directed.

S & F stack clamp made of 50 mm X 5 mm flat iron and 16 mm dia round iron stay including nut bolts and securing ends of stay to wall or roof suitable for 75 mm bore pipe complete all as specified and directed.

S & F in repairs for 75 mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and directed.

Taking down carefully any type of Point wiring (Light / Fan / Socket,bell or Power Point) complete, removing materials from site and making good the disturbed surfaces of walls, floors etc as per existing specification complete all as specified and as directed by the Engineer-in-Charge.

Taking down carefully old detoriated wooden meter board including all the electric meters, DP/TP switches fuse unit and all connected accessories, dismantling carefully electric meter and keep in safe custody for reuse complete all as specified and directed directed by EIC. Note:- The damaged surfaces to be madeby applying cement plaster, putty and colour wash etc matching with the existing surfacesas directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible.

Taking down old MCCBs/MCBs/Isolator any capacity and any make after disconnecting complete all as specified and directed.

Material and labor for point wiring with 1.5 sq mm PVC insulated unsheathed single core multi-stranded copper conductor cable 1100 Volts (FRLS) grade, drawn through and including 19 mm / 20 mm dia rigid non-metallic PVC concealed conduit (medium grade) along with 1.5 sq mm continuous PVC insulated unsheathed solid/stranded copper conductor cable (FRLS) for earth continuity wire, connected to earth dolly and to be terminated in pressed steel sunken boxes (having wall thickness not less than 1.22 mm for boxes upto a size of 200 mm x 300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type, covered with 3.0 mm thick bakelite sheet (Make: Hylum or equivalent) for mounting switches, sockets, fan regulators etc including testing on completion complete all as specified and as directed by the Engineer-in-Charge.

(a) One light /ceilingfan/wall fan/exhaust fan /independent socket/bell point controlled by one switch.

(b) One 3 pin socket outlet, 5 Amps on the same board with other switches.

(c) One light point controlled by two 2- way switches

All as per item No. 2 above but with 2.5 sqmm cable for phase/neutral & earth continuity for one three pin 15 Amps socket out let controlled by one switch.

M&L for submain wiring with two run of single core PVC insulated unsheathed multi stranded copper conductor FRLS cable of size 6 Sqmm 1100 volts grade and one run of PVC insulated unsheathed stranded copper conductor FRLS cable of size 6 Sqmm 1100 volts grade as earth continuity conductor drawn in drawn in existing concealed conduit on roof/wall/ceiling including making good the disturbed surfaces of wall etc including complete all as directed. Note : Two run of single core cable and one run of earth wire will be measured as one length.

S&F Socket out let 2 in1,3 pin,5A complete all as specified and directed.Make Anchor/Havells

S&F switch piano,flush type single pole,one way 5 Amps complete all as specified and directed.Make Anchor/Havells

S&F socket outlet 2 in 1 ,3 pin,5 and 15 amp all as specified and directed.Make Anchor/Havells

S&F switch Piano,flush type single pole , one way 15 amps complete all as specified and directed.Make Anchor/Havells

S/F LED Environmental friendly, ultra modern, energy saving, surface mounted, decorative oval bulk head edge-lit LED luminaire comprising of high brightness LEDs of 10W LED complete all as specified and directed. Make Havells / Phillips / Crompton

S&F switch piano,flush type single pole,two way 5 Amps complete all as specified and directed.Make Anchor/Havells

S&F bell Ding Dong AC. 230 volts, single pole all as specified and directed

S & F bell push flush type 5A, 230 volts, single pole all as specified and directed

S&F ceiling rose with earth terminal connection, 3 terminal/ PVC/ polycarbonate, isolated body.

S&F in repair LED 20Watt ,230 volt batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver complete with all accessories .Make Havells/Philips/Crompton

S & F lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings all as directed

S&F in repair Sheet metal enclosure TPN 4 way for DB's phosphatised, powder coated, single door, with 200 Amps rated bus bar, 415 V complete all as specified and directed. Make Havells/Legrand/Scheinider

S&F MCB four pole 63 Amps,240V, including taking down the old unserviceable Isolator of any type complete all as specified and directed. Make Havells/Legrand/L&T

S&F Sheet metal enclosure DB 12 way single door with 100 amps rated bus bar complete all as specified and directed. Make Sicinens/Legrand/Scheinider

S&F Sheet metal enclosure DB 8 way single door with 100 amps rated bus bar complete all as specified and directed. Make Sicinens/Legrand/Scheinider

S&F MCB SPN, 32 Amp,50Hz,240 Volts complete all as specified and directed .Make Havells/Legrand/L&T

S&F MCB SP 6-32 Amp, 10 KA, 230 Volt complete all as specified and directed . Make Havells/Legrand/L&T

M&L for earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to earth lead wire of GI wire 4mm dia by means of nuts/bolts and washers, check nuts of galvanized iron or steel including 15mm dia GI pipe light grade upto 1.5 mtr below GL for protection pipe, excavation and earth work charcoal dust, common salt, PCC 1:3:6 type C-1 chamber with cover and RCC 1:2:4 type B-1 using 20mm graded stone aggregate reinforced with 6mm dia round bars @ 75mm c/c both way with MS handle 12mm dia PGI funnel and wire mesh all as shown in electrical plate No 5 of SSR Part-I connected to ear thing test point all as specified or indicated including testing on completion all as directed by Engr-in-Charge.

Ramsons

M/s J P Traders

rehman construction company

M/s M Aali construction co